Figure 2 Bottom ports on AP302W access point 2 Insert the screws into the mounting bracket wall installation holes as shown in Figure 3, and use the screw-in anchors, if needed. Figure 5 Desk stand Figure 3 Wall installation holes The AP302W access point has the following features:
Radios:
Two 802.11ax radios (one 2x2 2.4 GHz and 5 GHz radio, and one 2x2 5 GHz radio) One IoT Radio (2.4 GHz/IEEE 802.15.4 Zigbee) Table 2 Bottom ports on AP302W access point Callout Description ExtremeWireless 802.11ax AP302W Indoor Access Point AP302W Overview The AP302W access point is an indoor model 802.11ax wallplate access point. The access point supports Wi-Fi 6, features built-in dual-band radios, three WiFi internal antennas, and one Bluetooth Low Energy (BLE) antenna. The AP302W access point can be mounted on a flat surface such as a wall, to a junction box, and can be installed on a desk stand. Note: The AP302W requires a minimum base firmware of WiNG 7.6.0 or IQEngine 10.3r0. Console port: custom micro-USB cable Six, 10/100/1000 Mbps ports:
Rear ports:
One Ethernet (ETH) port with Power over Ethernet (PoE) in One pass through port Bottom ports:
Two ETH ports One ETH port with power-sourcing-equipment (PSE) One pass through port LEDs: One The LED indicator will be on during reset One software reset button One Kensington lock One USB 2.0 type A connector, supports up to 2.5W Power: PoE 802.3at and 802.3af (see Table 1 for details) Antennas: four internal antennas Temperature:
Operating temperature: 0 C to +40 C (32 F to +104 F) Non-operating temperature: -40 C to +70 C (-40 F to +158 F) Enclosure: Plastic Table 1 AP302W Power source Power source Description PSE port (up to 12.5 W) USB port
(2.5 W) PoE at 802.3at 802.3at is provided through ETH0 Yes 802.3af 802.3af is provided through ETH0 No External 12 VDC power supply
(optional; ordering part #37215- PWR 12 VDC, 2A, 2.5 mm x 5.5 mm connector) Power is provided through an external DC power supply plugged into an AC source No Yes Yes Yes Note: PoE power is disabled when external power supply is used. Figure 1 Front and back views of AP302W 1 2 3 4 5 6 1 1 1 1 2 2 2 1 12 VDC power supply Pass through port ETH1 and PoE out port ETH2 port ETH3 port Status LED Status LED Amber color indicates non-operational status Green color indicates normal operational status Light Sensor The light sensor is located on the front face of the access point but is not visibly marked. AP302W Box Contents Ensure that the following items are available:
Table 3 Contents of the AP302W Box Quantity Item AP302W Quick Reference Access point Flat head T8 locking screw Flat pan head 6-32, 14 mm long black screws for USA junction box attachment Pan head M3.5x16 mm long screws for solid wall or anchor attachment 25 mm long white plastic screw-in anchors 100 mm RJ45 cable (not including connectors), CAT.5E flat LAN cable All optional brackets and accessories are sold separately. For detailed installation instructions about all mounting procedures, refer to the ExtremeWireless AP302W Access Point Installation Guide in the Extreme Networks Documentation Support site. Install the Access Point Electrical Hazard: Only qualified personnel must perform installation procedures. Use these instructions as guidelines for mounting and connecting the AP302Waccess points easily and safely. The AP302W comes with a stainless-steel mounting bracket that can be used to mount the access point on flat surfaces such a wall or solid ceiling, or to a junction box. An optional desk stand is available for mounting the access point to a desk. Note: For system Ethernet lines with receptacle, use the included RJ45 to RJ45 cable to connect the Ethernet cable to the access point. For system Ethernet lines without receptacle, connect the system Ethernet cable into the access point back ETH0 port. Tools Required One < 1/4 in. flat-head or #1 Phillips head screwdriver One torx screwdriver with T8 or VT8 bit Install the Access Point on a Wall Pre-installation checklist:
The mounting surface, item, and hardware must be able to support the access point in all environmental conditions. The mounting surface must be flat. 1 Using the stainless-steel mounting bracket as a template, mark and drill the wall installation holes on the wall. Insert the Ethernet cable into the ETH0 port. 3 4 Insert the access point onto the bracket locking tab and slide it down until it is fully 5 Attach the security locking screw to the security locking tab on the wall bracket, and seated onto the bracket. lock the access point in place. If you want to install the access point on a solid ceiling or a dry wall, you need to create a hole from behind the wall to run the RJ45 cable. For more information, refer to the ExtremeWireless AP302W Access Point Installation Guide. Install the Access Point on a Junction Box Use the stainless steel mounting bracket to mount the access point on a junction box. 1 2 Remove the screws from the box. Line up the bracket holes with the large hole on the box. Note: When you line up the holes, the bracket locking tab must be pointing up and the box must be fully covered by the bracket. 3 Using the aligned holes, attach the bracket to the box using the screws removed from the box earlier. Mounting bracket for wall or junction box or solid ceiling Figure 4 Stainless-steel mounting bracket for wall or junction box Note: The installer must supply the required tools for installation. Large hole to place on the junction box and run the RJ45 cable through Table 4 Stainless-steel mounting bracket parts Callout Description Security locking tab Bracket locking tab Junction box installation hole 1 2 3 4 4 Connect the Ethernet cable or the RJ45 flat cable to the access point. 5 Align the keyhole slots and posts, and then slide the access point onto the bracket 6 Using a security torx T-8 or a VT-8 screw, secure the bracket locking tab for physical until it is fully seated in place. security. Install the Access Point on a Desk Stand Use the optional desk stand, that need to be purchased separately, for this installation. 1 Line up the access point on the mounting tabs of the desk stand. 2 Slide the access point on the desk stand until it is fully seated and lock it in place. 3 Attach the security locking tab screw to the security locking tab on the desk stand, and lock the access point in place. 4 Insert the RJ45 cable into the access point. Connect a Power Supply If you need to power theAP302W access point with an external 12 VDC power supply, you can plug the power cord into the power connector on the back of the access point. There is no wall mount for the 12 VDC power supply. The power LED on the front face of the access point is lit when the power supply is connected. For information about optional power supplies, refer to the ExtremeWireless AP302W Access Point Installation Guide. Professional Installation Instruction Installation personnel This product is designed for specific application and needs to be installed by a qualified personnel who has RF and related rule knowledge. The general user shall not attempt to install or change the setting. Installation procedure Refer to the ExtremeWireless AP302W Access Point Installation Guide. Warning: Select the installation position and ensure that the final output power does not exceed the limit set forth in relevant rules. The violation of the rule could lead to serious federal penalty. Instructions d'installation professionnelle Installation Ce produit est destine a un usage specifique et doit etre installe par un personnel qualifie maitrisant les radiofrequences et les regles s'y rapportant. L'installation et les reglages ne doivent pas etre modifies par l'utilisateur final. Procedure d'installation Consulter le manuel d'utilisation ExtremeWireless AP302W Access Point Installation Guide. Warning: Avertissement: Choisir avec soin la position d'installation et s'assurer que la puissance de sortie ne depasse pas les limites en vigueur. La violation de cette regle peut conduire a de serieuses penalites federales. GE and Console Connections The AP302W has four GE (Ethernet) ports and a Console port. During administration and maintenance through the Console, the access point must still have a power connection through either an Ethernet PoE cable or an external DC power supply. Internal Antenna Configuration Information Table 5 AP302W antenna configuration Software mode Radio 1 Radio 2 Description Mode 1 Mode 2 Mode 3 2.4 GHz 5 GHz - full Dual-band dual concurrent 2 GHz/ 5 GHz - full 5 GHz - full R1 unlocked sensor 5 GHz - low 5 GHz - high Dual 5 GHz band dont le gain est suprieur au gain maximal indiqu pour tout type figurant sur la liste, sont strictement interdits pour l'exploitation de l'metteur. European Waste Electrical and Electronic Equipment
(WEEE) Notice Regulatory and Compliance Information Safety Guidelines This section contains notices that are intended to protect your personal safety and to prevent damage to the equipment. Qualified Personnel:
Electrical Hazard: Only qualified personnel must perform installation procedures. Within the context of the safety notes in this documentation, qualified persons are defined as persons who are authorized to commission grounding devices, systems, and circuits in accordance with established safety practices and standards. A qualified person understands the requirements and risks involved with installing outdoor electrical equipment in accordance with national codes. Warning: MPE Statement - Mobile device: This equipment complies with EU radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 23 cm between the radiator and your body. Federal Communications Commission (FCC) Notice Warning: This device is restricted for indoor use. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
Reorient or relocate the receiving antenna. Connect the equipment into an outlet on a circuit different from that to which the Increase the separation between the equipment and receiver. receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Warning: FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 23 cm between the radiator and your body. Industry Canada Notice Warning: For indoor use only. Pour une utilisation en intrieur uniquement. This device complies with ISEDs licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Le prsent appareil est conforme aux CNR d ISED applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes : (1) le dispositif ne doit pas produire de brouillage prjudiciable, et (2) ce dispositif doit accepter tout brouillage reu, y compris un brouillage susceptible de provoquer un fonctionnement indsirable. Caution: The device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems. Caution: Avertissement: les dispositifs fonctionnant dans la bande 5150-
5250 MHz sont rservs uniquement pour une utilisation lintrieur afin de rduire les risques de brouillage prjudiciable aux systmes de satellites mobiles utilisant les mmes canaux. Warning: IC Radiation Exposure Statement: This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 23 cm between the radiator and your body. Warning: Dclaration d'exposition aux radiations: Cet quipement est conforme aux limites d'exposition aux rayonnements ISED tablies pour un environnement non contrl. Cet quipement doit tre install et utilis avec un minimum de 23 cm de distance entre la source de rayonnement et votre corps. This radio transmitter [IC: 4141B-AP302W] has been approved by Innovation, Science and Economic Development Canada to operate with the antenna types listed in ExtremeWireless AP302W Access Point Installation Guide, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device. Le prsent metteur radio [IC: 4141B-AP302W] a t approuv par Innovation, Sciences et Dveloppement conomique Canada pour fonctionner avec les types d'antenne rpertoris dans le Guide d'installation des points d'accs sans fil extrmes AP302W, avec le un gain admissible maximal. Les types d'antenne non inclus dans cette liste, et Australia Notice Warning: AU co-location MPE Statement: This equipment complies with AU radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 24 cm between the radiator and your body. Other Countries Japan 5 GHz band (W52, W53). Indoor use only, except for communication with high power radio. Brazil Este produto est homologado pela ANATEL, de acordo com os procedimentos regulamentados pela Resoluo n. 242/2000 e atende aos requisitos tcnicos aplicados. Este equipamento no tem direito proteo contra interferncia prejudicial e no pode causar interferncia em sistemas devidamente autorizados. Para maiores informaes, consulte o site da ANATEL www.anatel.gov.br Hazardous Substances This product complies with the requirements of Directive 2011/65/EU of the European Parliament and of the Council of 8 June 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment. NCC Statement The device is restricted to indoor use only when operating in the 5150 to 5350 MHz frequency range. CE Information Warning: CE co-location MPE Statement: This equipment complies with CE radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 20 cm between the radiator and your body. AT EE IT PT BE FI LV RO BG FR LT SK HR DE LU SI CY EL MT ES CZ HU NL SE DK IE PL UK AP302W All Operational Modes 2.4GHz: 802.11b, 802.11g, 802.11n (HT20), 802.11n (HT40), 802.11ax (HEW20), 802.11ax
(HEW40), 802.15.4 (Thread), Bluetooth (LE) 5GHz: 802.11a, 802.11n (HT20), 802.11n (HT40), 802.11ac (VHT20), 802.11ac (VHT40), 802.11ac (VHT80), 802.11ac (VHT160), 802.11ax (HEW20), 802.11ax (HEW40), 802.11ax
(HEW80), 802.11ax (HEW160) The frequency and the maximum transmitted power in EU are listed below:
2412-2472 MHz: 19.98 dBm 2402-2480 MHz (LE): 7.78 dBm 5180-5240 MHz: 22.99 dBm 5260-5320 MHz: 22.99 dBm 5500-5700 MHz: 29.99 dBm 2405-2480 MHz: 7.79 dBm In accordance with Directive 2012/19/EU of the European Parliament on waste electrical and electronic equipment (WEEE):
1 The symbol above indicates that separate collection of electrical and electronic equipment is required. 2 When this product has reached the end of its serviceable life, it cannot be disposed of as unsorted municipal waste. It must be collected and treated separately. 3 It has been determined by the European Parliament that there are potential negative effects on the environment and human health as a result of the presence of hazardous substances in electrical and electronic equipment. 4 It is the users responsibility to utilize the available collection system to ensure WEEE is properly treated. For information about the available collection system, please contact Extreme Environmental Compliance at Green@extremenetworks.com. 5 Declaration of Conformity in Languages of the European Declaration of Conformity in Languages of the European Community English Finnish Dutch French Swedish Danish German Greek Icelandic Italian Spanish Hereby, Extreme Networks declares that the radio equipment type
(AP302W) is in compliance with Directive 2014/53/EU. For full text of the EU Declaration of Conformity, please contact Extreme Regulatory Compliance at compliancerequest@extremenetworks.com Tten Extreme Networks vakuuttaa, ett Radio laite tyyppi (AP302W) on direktiivin 2014/53/EU mukainen.EU vaatimustenmukaisuusvakuutuksen tydellisest tekstist ota yhteytt rimmisiin viranomais sdksiin osoitteessa compliancerequest@extremenetworks.com Extreme Networks verklaart hierbij dat het type radioapparatuur
(AP302W) in overeenstemming is met richtlijn 2014/53/EU.Voor de volledige tekst van de EU-conformiteitsverklaring u contact opnemen met extreme regelgeving op compliancerequest@extremenetworks.com Par la prsente, Extreme Networks dclare que le type d'quipement radio (AP302W) est conforme la directive 2014/53/UE.Pour le texte intgral de la Dclaration de conformit de l'UE, veuillez communiquer avec Extreme Regulatory Compliance compliancerequest@extremenetworks.com Hrmed intygar Extreme Networks att radioutrustning typ (AP302W) verensstmmer med direktiv 2014/53/EU.Fr fullstndig text av EU-
frskran om verensstmmelse, vnligen kontakta Extreme regelefterlevnad p compliancerequest@extremenetworks.com Herved erklrer Extreme Networks, at radioudstyrs typen (AP302W) er i overensstemmelse med direktiv 2014/53/EU.For den fulde ordlyd af EU-
overensstemmelseserklringen bedes du kontakte Extreme Regulatory Compliance p compliancerequest@extremenetworks.com Dabei erklrt Extreme Networks, dass der Funkgertetyp (AP302W) mit der Richtlinie 2014/53/EU im Einklang steht.Fr den vollstndigen Wortlaut der EU-Konformittserklrung wenden Sie sich bitte an extreme Regulatory Compliance unter compliancerequest@extremenetworks.com
(AP302W) 2014/53/
. , compliancerequest@extremenetworks.com Hrlendis, Extreme Networks, lsa v yfir a tvarpsbnaargerin
(AP302W) s samrmi vi tilskipun 2014/53/ESB.Fyrir fullan texta ESB yfirlsingu um samrmi, vinsamlegast hafu samband vi Extreme Reglufylgni compliancerequest@extremenetworks.com Di conseguenza, Extreme Networks dichiara che il tipo di apparecchiature radio (AP302W) conforme alla direttiva 2014/53/EU.Per il testo integrale della Dichiarazione di conformit dell'UE, contattare Extreme Regulatory Compliance presso compliancerequest@extremenetworks.com Por la presente, Extreme Networks declara que el tipo de equipo radioelctrico (AP302W) cumple con la Directiva 2014/53/UE.Para obtener el texto completo de la Declaracin de conformidad de la UE, pngase en contacto con Extreme Regulatory Compliance en compliancerequest@extremenetworks.com Portuguese Por este meio, a Extreme Networks declara que o tipo de equipamento de rdio (AP302W) est em conformidade com a Diretiva 2014/53/UE.Para obter o texto integral da Declarao de Conformidade da UE, contacte o cumprimento regulamentar extremo em compliancerequest@extremenetworks.com Malti B ' dan, netwerks estremi, jiddikjara li t-tip ta ' tagmir tar-radju
(AP302W) huwa konformi mad-Direttiva 2014/53/UE.Gat-test si tad-
dikjarazzjoni ta ' konformit tal-UE, jekk jogbok ikkuntattja lill-
konformit regolatorja compliancerequest@extremenetworks.com ExtremeWirelessTM Indoor Access Point Quick Reference AP302W Copyright 2020 Extreme Networks, Inc. All Rights Reserved. Notice Legal Notices Extreme Networks, Inc. reserves the right to make changes in specifications and other information contained in this document and its website without prior notice. The reader should in all cases consult representatives of Extreme Networks to determine whether any such changes have been made. The hardware, firmware, software or any specifications described or referred to in this document are subject to change without notice. Trademarks Extreme Networks and the Extreme Networks logo are trademarks or registered trademarks of Extreme Networks, Inc. in the United States and/or other countries. All other names (including any product names) mentioned in this document are the property of their respective owners and may be trademarks or registered trademarks of their respective companies/owners. For additional information on Extreme Networks trademarks, please see:
www.extremenetworks.com/company/legal/trademarks/
Documentation, Installation Videos, and Support For product support, including Documentation and Installation Videos, visit:
www.extremenetworks.com/documentation P/N 9036814-01 Rev AA