Installing the ExtremeWiNG Outdoor AP-
7662i/e Access Point Overview of the AP-7662i/e The AP-7662 is an IP67 rated outdoor Access Point with 802.11ac dual band 2:2 radios. The AP-7662 is easy to install, lightweight, and is available in an internal
(AP-7662i) and external (AP-7662e) antenna model. Each model includes 802.11 radios, an IoT radio, and a GPS radio. The AP-7662 model comes in two models: AP-7662i and AP-7662e. In this document, the functionality, feature, and the procedure applies to both the models when AP-7662i/e is used. Note: The AP-7662i/e requires a minimum base firmware of WiNG 5.9.1. The AP-7662i/e model has the following features:
Radios: 2 radios (2.4GHz and 5GHz); 1 IoT/BLE/802.15.4 Radio (2.4 GHz) Console Port: RJ45 One RJ45, 10/100/1000 Ethernet Port (GE1) with PoE One RJ45, 10/100/1000Mb Ethernet port (GE2) LEDs: 4 (see Figure 1) One Reset button Power: PoE 802.3af or 802.3at GPS Receiver (will be supported via a future firmware release) Antennas:
IP67 Connectors on all ports AP-7662i - Five internal antennas (four band locked antennas and one BLE antenna) AP-7662e- Five external antennas (four single band antennas and one BLE antenna) Temperature: -40 to 70*C ambient temperature Enclosure: Cast Aluminum base and Top In Figure 1, the top image indicates AP-7662i. Figure 2 shows the top and side views of AP-7662e. Figure 1 Top and Side Views of AP-7662i 1 IoT/BLE Radio 2 Radio - 5 GHz 3 Radio - 2.4 GHz 4 Status 5 GE1 (PoE IN) 6 GE2 7 Console/Reset 8 Vent Figure 2 Top and Side Views of AP-7662e 1 IoT/BLE Radio 2 Radio - 5 GHz 3 Radio - 2.4 GHz 4 Status 5 GE1 (PoE IN) 6 GE2 7 Console/Reset 8 2.4 G - Antenna 1 and 2 9 Vent 10 5G - Antenna 1 11 BLE/802.15.4 Antenna 12 5 G - Antenna 2 LEDs on the Front of the AP Amber LEDs indicate 5 GHz Wi-Fi Radio, Green LEDs indicate 2.4 GHz Wi-Fi Radio, and Blue LED indicates the IoT Radio. The Status LED is ON only during bootup. For detailed installation information about the AP-7662i/e, see the ExtremeWireless AP-7662i/e Installation Guide. Table 1 shows ways to power the AP-7662i/e. Table 1 Powering the AP-7662i/e Power Source Description Power over Ethernet
(PoE) Power is provided through the RJ45 Ethernet port (GE1 port). Verifying the AP-7662i/e Box Contents Verify the contents of the box and ensure that the following items are available:
Table 2 Contents of the AP-7662i/e Box Quantity Item AP-7662i/e Quick Reference Guide Cloud Quick Start Card 1 1 The following hardware is included:
1 1 M4 screw assembly with star washer Ring terminal Mounting and Connecting the AP Electrical Hazard: Only qualified personnel should perform installation procedures. Use these instructions as guidelines for mounting and connecting the AP-
7662i/e easily and safely. The AP-7662i/e mounting brackets are sold separately. For more information about installing the optional bracket and the adapter, see the ExtremeWireless AP-7662i/e Installation Guide. For installation videos of the AP, see www.extremenetworks.com/support/
Mounting the AP-7662i/e Use these instructions as guidelines for mounting and connecting the AP-
7662i/e easily and safely. The installation of the AP-7662i/e should be performed by a professional installer to ensure proper operation and compliance with local safety guidelines. Attach the AP-7662i/e to a surface that can support the AP and in an environment it can withstand. It can be mounted to a wall, girder, ceiling, or pole, and the surface material can be concrete, brick, wood, metal, or plastic. Positioning the AP for Installation Mount the AP so that the glands are on the side of the AP closest to the ground, and not above the plastic cover. You must provide a 3-inch drip loop on all cables. Note: Do not remove the dust cap until you need to install the BLE/
IoT antennas. Attach the Ground Wire Use the M4 ground screw assembly, with the star washer, to attach the ground wires ring terminal to the back of the AP. The wire should be as close to the AP bottom as possible. Tighten the screw to a torque of 13.0-13.5 in-
lbs. Note: Attach the H bracket after attaching the ground wire onto the AP. Tighten the torque, tighten the screws, and attach the LAN cable. Mounting the AP-7662i/e to a Wall 1 Determine the diameter of the pole. Note: The H type Mounting Bracket (WS-MBO-H01) is sold as a separate accessory (ordering part #30519). 1 Using the mounting bracket as a guide, mark the location for the mounting screws. The wall bracket provides eight attachment holes. Use four (one in each corner). Place the bracket and mark the four hole centers. 2 Drill four holes into the wall as follows:
for installing the AP on a masonry wall, use a 5/16 diameter bit. for other materials, use the appropriate drill for the screws being used. 3 For masonry installations, drill at least 1/8 (3mm) past the depth of the screw, or bolt, being used, and place four anchor assemblies into the holes. 4 Attach the AP to the H Bracket:
a Use four M4 screw assemblies to attach the AP to the H bracket on the side that does not have the PEM stand-offs. b Tighten the four screws to a torque of 13.0-13.5 in-lbs. Figure 3 Attaching the H Bracket to the AP 5 Secure the anchors to the wall, then secure the bracket to the anchors. 6 If using #10 screws, tighten them to a torque of 25 in-lbs. If using screws, tighten them to 45 in-lbs. Figure 4 AP-7662i Wall Mount H Bracket Figure 5 AP-7662e Wall Mount H Bracket Pole Diameter
<= 2.5 (63.5mm) 5 - 7 (178mm) Cable Clamp Size Use small cable clamp. Use large cable clamp For other pole diameters, provide your own stainless steel cable clamp. The band must be (12.7mm) wide. 2 Attach the AP to the Pole Mount bracket using 4 M4 screws. Tighten the four screws to a torque of 13.0-13.5 in-lbs. Figure 6 Attaching a Pole Bracket to the AP 3 Attach the cable clamp to the pole bracket. Open the cable clamp by turning a flat bladed screwdriver counterclockwise. Then, insert the non-
clamp end into the pole bracket through the holes. Note: It is easier to install both clamps before attaching to the pole. 4 Put the metal band around the pole and insert it into the clamp. Turn the clamp screw clockwise, tightening the band around the pole. Figure 7 AP with Mounting BracketVertical Pole Mounting the AP-7662i/e to a Wall/Pole using the WS-MBO-ART01 2 Axis Extension Arm You can mount the to AP-7662i/e to a wall or a pole using a 10 extension arm
(WS-MBO-ART01, ordering part #30514). For mounting and installation instructions, refer to the ExtremeWireless AP-7662i/e Installation Guide. Installing External Antennas 1 Professionally install the external antennas intended for area coverage. For information about antenna selection and installation, refer to the External Antenna Site Preparation and Installation Guide. 2 Attach the external antenna cables to the Standard Polarity Type-N connectors on the AP-7662i/e. Mounting the AP-7662i/e to a Pole Note: The Pole Mounting Bracket (WS-MBO-POLE01) is sold as a separate accessory (ordering part #30520). Connecting a Power Supply to the AP-7662i/e If you need to power the AP-7662i/e, you can do so my using the GE1 port on the AP. The power LED on the front face of the AP illuminates when the device is powered on. Refer to the ExtremeWireless AP-7662i/e Installation Guide for more information. LAN/Console Connections The AP-7662i/e has two LAN (Ethernet) ports and a Console port. Refer to Figure 1 and Figure 2 for the location of these ports. During administration and maintenance through the LAN or Console, the AP must still have a power connection through either an Ethernet PoE cable or a DC power supply. Professional Installation Instruction Installation personnel This product is designed for specific application and needs to be installed by a qualified personnel who has RF and related rule knowledge. The general user shall not attempt to install or change the setting. Installation location The product shall be installed at a location where the radiating antenna can be kept 20 cm from nearby person in normal operation condition to meet regulatory RF exposure requirement. External antenna Use only the antennas which have been approved by the applicant. The non-
approved antenna(s) may produce unwanted spurious or excessive RF transmitting power which may lead to the violation of ISED limit and is prohibited. Installation procedure Please refer to users manual for the detail. Warning: Please carefully select the installation position and make sure that the final output power does not exceed the limit set force in relevant rules. The violation of the rule could lead to serious federal penalty. Instructions d'installation professionnelle Installation Ce produit est destine a un usage specifique et doit etre installe par un personnel qualifie maitrisant les radiofrequences et les regles s'y rapportant. L'installation et les reglages ne doivent pas etre modifies par l'utilisateur final. Emplacement d'installation En usage normal, afin de respecter les exigences reglementaires concernant l'exposition aux radiofrequences, ce produit doit etre installe de facon a respecter une distance de 20cm entre l'antenne emettrice et les personnes. Antenn externe Utiliser uniiquement les antennes approuvees par le fabricant. L'utilisation d'autres antennes peut conduire a un niveau de rayonnement essentiel ou non essentiel depassant les niveaux limites definis par ISED, ce qui est interdit. Procedure d'installation Consulter le manuel d'utilisation. Warning: Avertissement: Choisir avec soin la position d'installation et s'assurer que la puissance de sortie ne depasse pas les limites en vigueur. La violation de cette regle peut conduire a de serieuses penalites federales. Regulatory and Compliance Information Safety Guidelines This section contains notices that are intended to protect your personal safety and prevent damage to the equipment. Qualified Personnel:
Electrical Hazard: Only qualified personnel should perform installation procedures. Within the context of the safety notes in this documentation, qualified persons are defined as persons who are authorized to commission, ground and label devices, systems, and circuits in accordance with established safety practices and standards. A qualified person understands the requirements and risks involved with installing outdoor electrical equipment in accordance with national codes. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Operations in the 5.15-5.25GHz frequency range, it is restricted to indoor environment. This device meets all the other requirements specified in Part 15E, Section 15.407 of the FCC Rules. Warning: FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Industry Canada Notice This device complies with ISEDs licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Le prsent appareil est conforme aux CNR d ISED applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes : (1) le dispositif ne doit pas produire de brouillage prjudiciable, et
(2) ce dispositif doit accepter tout brouillage reu, y compris un brouillage susceptible de provoquer un fonctionnement indsirable. Caution :
1 The device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems;
2 The maximum antenna gain permitted for devices in the band 5725-5850 MHz shall be such that the equipment still complies with the e.i.r.p. limits specified for point-to-point and non-point-to-point operation as appropriate; and 3 Users should also be advised that high-power radars are allocated as primary users (i.e. priority users) of the bands 5650-5850 MHz and that these radars could cause interference and/or damage to LE-LAN devices. Avertissement:
1 les dispositifs fonctionnant dans la bande 5150-5250 MHz sont rservs uniquement pour une utilisation lintrieur afin de rduire les risques de brouillage prjudiciable aux systmes de satellites mobiles utilisant les mmes canaux;
2 le gain maximal d'antenne permis (pour les dispositifs utilisant la bande de 5725 5 850 MHz) doit tre conforme la limite de la p.i.r.e. spcifie pour l'exploitation point point et lexploitation non point point, selon le cas;
3 De plus, les utilisateurs devraient aussi tre aviss que les utilisateurs de radars de haute puissance sont dsigns utilisateurs principaux (c.--d., quils ont la priorit) pour les bandes 5650-5850 MHz et que ces radars pourraient causer du brouillage et/ou des dommages aux dispositifs LAN-
EL. Warning: IC Radiation Exposure Statement: This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Warning: Dclaration d'exposition aux radiations: Cet quipement est conforme aux limites d'exposition aux rayonnements ISED tablies pour un environnement non contrl. Cet quipement doit tre install et utilis avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps. Federal Communications Commission (FCC) Notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
Reorient or relocate the receiving antenna. Connect the equipment into an outlet on a circuit different from that to Increase the separation between the equipment and receiver. which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. European Waste Electrical and Electronic Equipment
(WEEE) Notice In accordance with Directive 2012/19/EU of the European Parliament on waste electrical and electronic equipment (WEEE):
1 The symbol above indicates that separate collection of electrical and electronic equipment is required. 2 When this product has reached the end of its serviceable life, it cannot be disposed of as unsorted municipal waste. It must be collected and treated separately. 3 It has been determined by the European Parliament that there are potential negative effects on the environment and human health as a result of the presence of hazardous substances in electrical and electronic equipment. 4 It is the users responsibility to utilize the available collection system to ensure WEEE is properly treated. For information about the available collection system, please contact Extreme Customer Support at +353 61 705500 (Ireland). Hazardous Substances This product complies with the requirements of Directive 2011/65/EU of the European Parliament and of the Council of 8 June 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment. Declaration of Conformity in Languages of the European Community English Finnish Dutch Hereby, Extreme Networks, declares that this Radio LAN device is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. Valmistaja Extreme Networks vakuuttaa tten ett Radio LAN device tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja sit koskevien direktiivin muiden ehtojen mukainen. Hierbij verklaart Extreme Networks dat het toestel Radio LAN device in overeenstemming is met de essentile eisen en de andere relevante bepalingen van richtlijn 1999/5/EG. Bij deze verklaart Extreme Networks dat deze Radio LAN device voldoet aan de essentile eisen en aan de overige relevante bepalingen van Richtlijn 1999/5/EC. French Par la prsente Extreme Networks dclare que l'appareil Radio LAN device est conforme aux exigences essentielles et aux autres dispositions pertinentes de la directive 1999/5/CE. Swedish Danish German Greek Icelandic Italian Spanish Portuguese Malti Par la prsente, Extreme Networks dclare que ce Radio LAN device est conforme aux exigences essentielles et aux autres dispositions de la directive 1999/5/CE qui lui sont applicables. Hrmed intygar Extreme Networks att denna Radio LAN device str I verensstmmelse med de vsentliga egenskapskrav och vriga relevanta bestmmelser som framgr av direktiv 1999/5/EG. Undertegnede Extreme Networks erklrer herved, at flgende udstyr Radio LAN device overholder de vsentlige krav og vrige relevante krav i direktiv 1999/5/EF. Hiermit erklrt Extreme Networks die bereinstimmung des "WLAN Wireless Controller bzw. Access Points" mit den grundlegenden Anforderungen und den anderen relevanten Festlegungen der Richtlinie 1999/5/EG. Extreme Networks Radio LAN device 1999/5/
. Extreme Networks lysir her med yfir a thessi bunadur, Radio LAN device, uppfyllir allar grunnkrofur, sem gerdar eru i R&TTE tilskipun ESB nr 1999/5/EC. Con la presente Extreme Networks dichiara che questo Radio LAN device conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE. Por medio de la presente Extreme Networks declara que el Radio LAN device cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE. Extreme Networks declara que este Radio LAN device est conforme com os requisitos essenciais e outras disposies da Directiva 1999/5/
CE. Hawnhekk, Extreme Networks, jiddikjara li dan Radio LAN device jikkonforma mal-htigijiet essenzjali u ma provvedimenti ohrajn relevanti li hemm fid-Dirrettiva 1999/5/EC. ExtremeWiNGTM Access Points Quick Reference P/N 37121 AP-7662-680B30-US P/N 37122 AP-7662-680B30-WR P/N 37123 AP-7662-680B40-US P/N 37124 AP-7662-680B40-WR Notice Copyright 2017 Extreme Networks, Inc. All Rights Reserved. Legal Notices Extreme Networks, Inc., on behalf of or through its wholly-owned subsidiary, Enterasys Networks, Inc., reserves the right to make changes in specifications and other information contained in this document and its website without prior notice. The reader should in all cases consult representatives of Extreme Networks to determine whether any such changes have been made. The hardware, firmware, software or any specifications described or referred to in this document are subject to change without notice. Trademarks Extreme Networks and the Extreme Networks logo are trademarks or registered trademarks of Extreme Networks, Inc. in the United States and/or other countries. All other names (including any product names) mentioned in this document are the property of their respective owners and may be trademarks or registered trademarks of their respective companies/owners. For additional information on Extreme Networks trademarks, please see:
www.extremenetworks.com/company/legal/trademarks/
Documentation & Support For product support, including documentation, visit:
www.extremenetworks.com/support/
P/N 9035167-01