Security camera ModelName:ECM-CL25A Product structure 1. Time display 2. Blue status indicator 3. Night light 4. Camera lens 5. Clock setting key 6. UP 12/24 shift key 7. DOWN 8. ON/OFF key 9. Start key 10. Motion detection 11. Video recording 12. Continuous photograph mode 13. Sound recording 14. Charge indicator 15. USB 16. TF card 17. Battery Quick operation guidance I. Time setting 1. Press SET once to set up hour, press UP/DOWN to select current time, press SET to set up minutes, press UP/DOWN to select current minutes, then press SET again to finish setting. (As shown in the figure below) II. Device installation III. Video operation 1. Open battery cover to remove battery insulation piece. Turn switch to ON, insert TF card, plug charger on. 1. To start up, press constantly on. once, the device enters standby mode, blue light is 2. For video recording, press once by pointing remote control to the device, blue light flashes three times, then the device starts to record video. again to save, blue light is constantly on, device enters standby Press mode. Then you may switch to the next mode. 3. For motion detection video recording, press once by pointing remote control to the device, blue light flashes four times, then start motion detection video recording. Press enters standby mode, then you may switch to the next mode. again to save, blue light is constantly on. Device once by pointing remote 4. For continuous photograph operation, press control to the device, blue light flashes twice, then the device starts to take pictures. Press standby mode, then you may switch to the next mode. again to save, blue light is constantly on, the device enters 5. For sound recording, press once by pointing the remote control to device, blue light flashes five times, then the device starts to record sound. again to save, blue light is constantly on. The device enters Press standby mode, you may switch to the next mode. 6. For night light operation, press once in any mode, night light starts, again, you may turn off the night light. blue light flashes once. Press 7. Key operation is the same remote operation. IV. Video time setting and function setting 1. For first use, you need to insert TF card to start up, the device will generate a document automatically. Turn off the device, open setting document in TF card by data line or card reader, setting image will appear
(specific operations are as below).
*Function introduction 1.VERSION = 2015090101 # DO NOT CHANGEDevice version No. 2.RESOLUTICON = 0 # (0=1080p@30fps, 1= 720p@60fps) Selection of resolution ratio 3.VIDEO_TIME = 3 # (0=1mins, 1=2mins, 2=3mins,3=5mins,4=10mins,5=15mins) recording interval timeSelection of video sections 4. QUALITY = 0 # (0=fine, 1=good, 2=normal)Selection of video result.0=Good 1=Medium 2=Poor 5. LOOP_RECORD = 1 # (0=off, 1=on)Selection of circulating video 6. DATE_STAMP = 1 # (0=off, 1=on)Selection of time mark 7. AUDIO_RECORD = 1 # (0=off, 1=on) Sound recording0= video with sound1=video without sound 8. AUTO_POWER_OFF = 1 # (0=Off, 1=3min,2=5min,3=10min)select automatic turnoff time without any operation 9. TIME_SET = N2015.01.01.00:00:00 # (Y=change N=No changetime settingwhen change, turn N to Y 10. DEFAULT_SETTING = 0 # (0=false, 1=true)Restore factory setting 11. MOTIONDETECT_LEVEL = 0 # (0=high, 1=mid, 2=low)motion detection sensitivity0=high 1=medium 2=low
* Note: When set up, please observe original format and value modification in the document to avoid invalid setting (as shown in the figure below).
* Save after modification, and then start up again. Settings are done. V. Parameters. 90*64.5*50.2MM 1920*1080 500W H.264 140 degree AVI TF 64G Device dimension Resolution ratio Pixel Compressed format Angle Video format Type of memory card Maximum capacity of memory card Player USB interface Operation system Distance of remote control Scope of sound recording 40 6M Motion detection camera distance Power consumption Adapter Batter capacity Video time frame 300MA/3.7V 5V/2A 2400MA 5 minutes Media player/KMplayer USB1.1/2.0 note:It couldn't transfer data with PC 2000/XP/Visat32 8M 30 s Photograph interval Sound record time frame 30 minutes Motion detection time frame Video recording consumption Picture consumption 1 minute 5 minutes/677MB 1 sheet/1.41MB VI. Notes 1. For first use of 64G TF card, please format the TF card in computer first. 2. After continuous photographing is full, clean up contents in the card. Blue light flashes continuously to indicate card is full. 3. When charge, red light is on; when charged full, red light is off. VII. Precautions Application occasions: please observe national laws and regulations strictly. Do not use this product for other illegal purposes, otherwise it will be at your own risk. Software upgrade: for better performance of the product, factory will continue to improve product software. This product allows upgrading software by customers themselves. Please consult local dealers for latest software information and upgrade method. Operating temperature: please use it under natural temperature. Do not work under temperature which is not suitable for human body. Operating humidity: please use it under humidity suitable for human life. Do not put it under humid environment. The product is not water proof. Shooting illumination: please use it under sufficient light source. Do not put camera under highlight source such as sun so as to prevent optical devices from being damaged. Cleaning requirements: do not use it under environment with oversize dust density so as to prevent camera lens and other parts from being contaminated by dust and to protect camera shooting results. You may swipe clean the camera lens gently by lens paper or cloth. Keep it clean. Other matters: this is precision electronic products. Keep it away from strong impact or vibration; do not use it under high-intensity magnetic field or electrical field. FCC NOTE This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS OR CHANGE TO THIS EQUIPMENT. SUCH MODIFICATIONS OR CHANGE COULD VOID THE USERS AUTHORITY TO OPERATE THE EQUIPMENT.