FCC ID: 2AIYW-E550 Smart Home Controller

Smart Home Controller User Guide Table of contents Chapter 1 Introduction Package contents Features LEDs Chapter 2 Initial Installation Requirements Procedure Chapter 3 Configuration Configuration Program Appendix A Specifications Regulatory Approvals User Guide 2 Chapter 1 Introduction This chapter provides an overview of the Ezlo Secure Gateways features and capabilities An always-on solution that works even in the event of a power or internet outage, the Ezlo Secure is a feature-rich control hub that keeps users in control of their home from anywhere, at any time. It offers control for Z-Wave, Zigbee, and 2GIG devices while also enabling control of Wi-Fi devices paired to Amazon Alexa or Google Assistant. It features local control for fast responsiveness, and through the Vera app gives customers remote access, personalized notifications, and scene creation ability. Package content The Ezlo Secure comes with an ethernet cable, power adapter, and quick start guide. Each Ezlo Secure is shipped under a unique serial number shown on the packaging. Users should retain packaging for reference. Features CPU: Quad-Core Cortex-A7 ARM Memory: 16GB EMMC Flash and 512MB DDR3 LAN: 10/100 Ethernet port with RJ45 connector Z-Wave Plus, 700 Series ZigBee 3.0 345MHz 2GIG receiver 802.11g/n/ac Dual Band WiFi 2.4 & 5GHz 4G/LTE supporting bands B2/B4/B5/B12/B13/B14/B66/B71 Bluetooth Low Energy 5.0 Host USB 2.0 port Reset button Top surface RGB LED 5V/3A power User Guide 3 LEDs Top-mounted LEDs Booting / Power ON Booting recovery partition Slow blinking Booting application partition Green Blue Slow waving Red Red System has booted but firmware not started Yellow Firmware has started Blue Rear/Top Panel Power port Connect the supplied power adapter here Ethernet port USB Port Reset Use a standard LAN cable (RJ45 connector) to connect your router to the port. The connector is a USB host with support for mass storage devices. Resetting the device to Factory Settings will remove all the information about included devices, scenes created, House modes settings, etc. Push and hold the RESET button at least 5 sec (on Ezlo Secure LED starts blinking RED), After that your Ezlo controller will be reset to factory defaults. Button on the top Multifunctional user button LAN Power Reset User Guide 4 Chapter 2 Initial Installation This chapter covers the software installation of the Ezlo Secure Gateway. Requirements Use a standard 10/100/1000 BaseT network (UTP) cable with RJ45 connector Procedure LAN Power Reset LAN Power Reset Connect the AC Power Adapter to your Ezlo Secure. Connect your Ezlo Secure to your internet gateway using an Ethernet cable. 1. Choose an Installation Site Select a suitable place to install the Ezlo Secure Gateway. 2. Connect LAN Cable Use a standard LAN cable to connect the device to the Ethernet port on the Ezlo Secure Gateway. 3. Power Up Connect the supplied power adapter to the Ezlo Secure Gateway. Use only the power adapter provided. Using a different one may cause hardware damage. 4. Check the LEDs The LED should be ON. User Guide 5 Chapter 3 Configuration Configuration Program This chapter provides Setup details of the System. The Ezlo Secure Gateway can offer customers seamless communication between devices while at home or away. This gateway is designed to provide complete connectivity with all certified devices including, security systems and ZigBee/ZWave/2GIG devices. Preparation iOS Android 1. Install the VeraMobile application on your phone Go to App store Search for VeraMobile app and install it Go to Google Play store Search for VeraMobile app and install it 2. Connect the AC Power Adapter to your Ezlo Secure 3. Connect your Ezlo Secure to your internet gateway using a LAN cable Using the mobile application 1. Open the VeraMobile app on your mobile phone 2. If you dont have an account after you open the app select New to Vera option and select from the list Ezlo Secure. 3. Select Wired setup. The app will walk you through the rest steps. 4. Select Scan Barcode you will see the screen with a camera and Add manually button. 5. Tap Add manually and enter the serial number and MAC address

(printed on the sticker) 6. You will see the congratulations screen with Ezlo Secure. 7. Ezlo Secure is ready to use. User Guide 6 Appendix A Specifications Ezlo Secure Model Dimensions Buttons Operating Temperature 0 C to 40 C Ezlo Secure 194x164x46 mm Functional button on the top surface and reset button on the back surface Network protocol TCP/IP Network Interface LEDs Power adapter 1 * 10/100 BaseT (RJ45) LAN connection RGB led 5V, 3A User Guide 7 Regulatory Approvals Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, includin g interference that may cause undesired operation. For indoor use only. Device does not operate in Band 5600-5650MHz. This equipment has been tested and found to comply with the limits for a Class Bdigit al device, pursuantto Part 15 of the FCC Rules. These limits are designed to provide reasonable protec- tion against harmful interference in ar esidential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in apar ticular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correctthe interference by one of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help. Changes or modications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. User Guide 8 Industry Canada Licence Exemption This device complies with Industry Canada licence-exempt RSS

(1) this device may not cause interference, and

(2) this device must accept any interference, including interference that ma y cause undesired operation of the device. For indoor use only. Device does not operate in Band 5600-5650MHz. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes :

(1) l'appareil ne doit pas produire de brouillage, et

(2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique fonctionnement. Pour usage intrieur uniquement. Lappareil ne fonctionne pas dans la bande 5600-5650 MHz. User Guide 9

EZLO INC. Request for Permanent Confidentiality Federal Communications Commission Equipment Authorization Division 7435 Oakland Mills Road Columbia, MD 21048 Date: 08/18/2020 Subject:

To Whom It May Concern:

In accordance with 0.457(d) and 0.459 of CFR 47, and KDB 726920, EZLO INC. hereby requests permanent confidentiality for documents filed under the following exhibit types:

(remove non-relevant exhibits from below standard list) FCC ID: 2AIYW-E550 1. Block Diagram 2. Schematic Diagram 3. Part List 4. Operational Description These items contain detailed system and equipment description and related information about the product which EZLO INC. considers to be proprietary, confidential and a custom design which otherwise would not be released to the general public. Since this design is a basis from which future technological products will evolve, EZLO INC. also feels that this information would be of benefit to its competitors, and that the disclosure of the information in these exhibits would give our competitors an unfair advantage in the market. We are aware that exhibit types cover letters, attestations, label document, test reports, RF exposure information (SAR and MPE reports), cannot be requested to be classified confidential and are thus subject to publication, as will be documents of all other exhibits types for which we have not requested a confidentiality classification. Best Regards, _______________________________ Signature Name: Roger Gregory Title: VP Product Management Company Name: EZLO INC. Address: 1255 Broad Street, Suite 100, Clifton, New Jersey 07013, USA

EZLO INC. Federal Communications Commission Equipment Authorization Division 7435 Oakland Mills Road Columbia, MD 21048 Date: 08/18/2020 Subject:

To Whom It May Concern:

FCC-ID: 2AIYW-E550 Request for Short Term Confidentiality In accordance with 0.457(d) and 0.459 of CFR 47, EZLO INC. hereby requests short term confidentiality for documents filed under the following exhibit types:

(remove non-relevant exhibits from below standard list) 1. External Photographs 2. Internal Photographs 3. User / Instruction Manual 4. Test Set-up Photographs until the product will be publicly announced. Short term confidentiality release date / period: 180 days from grant issue date These items contain detailed system and equipment description and related information about the product which EZLO INC. considers to be proprietary, confidential and a custom design which otherwise would not be released to the general public. Since this design is a basis from which future technological products will evolve, EZLO INC. also feels that this information would be of benefit to its competitors, and that the disclosure of the information in these exhibits would give our competitors an unfair advantage in the market. We are informed and aware of our obligation that we have to inform the involved TCB in written and in due time if we intend to market the product prior to the above specified confidentiality release date so that the short term confidentiality classification can be reset prior to product launch. We are aware that exhibit types cover letters, attestations, label document, test reports, RF exposure information (SAR and MPE reports), cannot be requested to be classified confidential and are thus subject to publication, as will be documents of all other exhibits types for which we have not requested a confidentiality classification. Best Regards, ____________________________________ Signature Name: Roger Gregory Title: VP Product Management Company Name: EZLO INC. Address: 1255 Broad Street, Suite 100, Clifton, New Jersey, 07013