AI-WIRELESS ROBOTIC POOL CLEANER USER MANUAL X80,X60X45X30W80W60 W45W30M80M60M45M30 THANK YOU FOR PURCHASING X80,X60X45X30W80W60W45W30M80 M60M45M30 AI-WIRELESS ROBOTIC POOL CLEANER Please read the manual carefully before installing or using it and keeping it for subsequent use. EN TIPS How to achieve the most efficient cleaning It is recommended to place the robot at the pool corner, which will facilitate quick coverage of the entire pool floor area. How to let the water drain out while removing robot from the pool Place the robot on the edge of the pool for a while and let the water drain out. How to open the filter box For battery protection, it is recommended that the robot should be fully charg ed every 3 months and magnetic cap should be inserted back if the robot not be used for more than 14 days. WARNINGS Information contained in this warnings page will help you operate the robot safely, protect yourself and others from hazards, and prevent damage to the robot and other property. GENERAL WARNINGS Read the instructions before operating the robot. The robot is designed for pool cleaning; do not use it for other purposes. Keep the robot out of the reach of children or persons with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction. Children should not play with the robot. The robot must be maintained by dealer except for simple routine maintenance written in this manual. Installers must follow manufacturers instruction and keep in compliance with national or local standards for installation. Under no circumstances will the manufacturer be held responsible for any outcome incurred by failure to comply with applicable standards or local regulations. Incorrect installation or use of the robot may cause serious damage to property or injuries to people. Do not enter pool while the robot is in water. WARNINGS ON USE For the purposes of recharging the battery, only use the detachable supply unit provided with this appliance, and operated this power supply at least 3.5 meters from the edge of the pool. Disconnect the robot from the power supply and insert back the magnetic cap before any maintenance on the robot. Do not operate the robots with wet hands. Disconnect the robot from the supply mains before carrying out user maintenance such as cleaning the filter. Do not try to repair the robot yourself or open engine box in case of malfunction, please contact your dealer. If there is any malfunction or release of odor from the robot when charging, disconnect it from the power supply immediately and contact your dealer. Use only original replacement parts supplied by the manufacturer for service and repair. SPECIAL CONDITIONS APPLICABLE TO ROBOT The robot is intended for swimming pools with a depth less than 3 meters and a water temperature between 0C ~ 35C. (Below 15C the endurance time may be affected) The robot will automatically stop running if the water depth is less than 40 centimeters for the purpose of motor protection. Do not use the robot during shock chlorination. Do not use the robot in thunder storm or stormy weather. Do not charge the robot outdoors Do not expose the robot to direct rainfall or sunlight for an extended period. Optimum storage temperature between -20-60 and storage humidity betw een 35%-85%/RH. CAUTIONS Rest/hold the robot by the pool edge for water to drain out before lifting the robot out of water, do it slowly so as to prevent back injury. Clean the filter basket after each cleaning cycle. Do not lift the robot out of water by track. When the robot battery is below 30%, it will clean the floor of the pool only. REMINDER Table of Contents SECTION 1. PRODUCT OVERVIEWS ............................................................................................. 1 1.1 Packaging content ................................................................................................................. 1 1.2 Technical specification ..........................................................................................................2 1.3 Preparation .............................................................................................................................. 3 SECTION 2. OPERATION ....................................................................................................................5 2.1 Introduction of button ......................................................................................................... 7 2.2 Operation on the display of the unit ............................................................................. 9 2.3 Cleaning filter basket .........................................................................................................10 2.4 Charging the robot ............................................................................................................. 11 2.5 WIFI matching for the robot .......................................................................................... 12 SECTION 3. MAINTENANCE .......................................................................................................... 13 3.1 Filter maintenance ............................................................................................................. 14 3.2 Impeller maintenance ........................................................................................................14 3.3 Replace the worn brushes ................................................................................................ 16 3.4 Replace the worn tracks .................................................................................................. 17 SECTION 4. TROUBLE SHOOTING ..............................................................................................18 SECTION 1. PRODUCT OVERVIEWS 1.1 Packaging content The following items are included in the packaging of robot. Please contact your dealer if any damage or loss. The robot Charger Hook Magnetic cap*2 User manual Note:
1. Remove the Magnetic cap when using or charging. Insert Magnetic cap to machine's bottom for battery protection when not using the robot for more than 14 days. 2. If software exception happens, insert Magnetic cap to machine's bottom for 2 seconds, then remove it to restart. 1 1.2 Technical specification Model X80,M80,W X60 X45,M45,W X30,M30,W 80 M60,W60 45 30 Performance condition reference*: Floor mode Endurance time 8h 6h 4.5h Performance condition reference*: Floor/wall/waterline mode Endurance time Charging time 4.5h 5h 3.5h 4h 2.5h 3h 3h 2h 2h Battery Optimum pool temperature 14Ah 10.4Ah 7.8Ah 5.2Ah
(352wh)
(262wh)
(196wh)
(131wh) 0~35 Cleaning mode Floor/Floor and Wall and Waterline Multiple cycle option 0.5h/1h/2h AI mode App application Filter capacity YES YES 3.2L Filtration accuracy 180 m(80mesh) Pump flow rate Running power Moving speed 20~10m
/h 30-110W 12m/min 2 Number of motors 3 Charger input 100-240VAC ~ 50/60Hz 1.5A Charger output 29.4Vdc, 2A Running voltage/current Robot NW/GW Robot dimension
(L*W*H) Robot packaging dimension (L*W*H) 25.2V/1.2A 12 / 17kg 495*395*265 mm 580*448*330 mm
* Reference: Above working time is based on 2 hours cleaning each time at floor mode in the liner pool. Note: The manufacturer reserves the right to modify these specifications without notice. 1.3 Preparation 3 Remove the Magnetic cap from the Remove the plug cover. After fully bottom of the robot and store it well. charged, the plug should be covered back. Connected to 90-265V power supply Install the configured hook on the rod through charger.
(Rod is exclusive). The red light of the power indicator is on:
charging The green light is of the power indicator is on: fully charged already. Please fully charge the robot before the first use. 4 SECTION 2. OPERATION CAUTION To prevent possible damages to the robot or people, be sure to follow these guidelines:
After cleaning is completed, put the robot in the cooling dry place against direct sunlight. The robot becomes heavier when filled with water. Pay special attention when lifting it out of the water, wait till water drains out from it. 5 IMPORTANT After settings are done, please drop the robot into the water within 3 minutes, or the robot will enter into the sleeping mode. Clean the filter basket after cleaning cycle, please avoid cleaning the surface of the filter box directly with your hands. The robot has a safety feature that automatically stops if a dry run happens. Move the robot slightly in all directions so that the air contained in the robot escapes, and the robot can go down into the water easily. (As showed in the pic below) 6 2.1 Introduction of button On/Off Cleaning Cleaning time mode AI Mode Error code Battery Wifi indicator signal Type of button Power switch Cleaning time setup Icon Display Status Description Green light flashes Setup status Running Green light being on status/Inspection status under water 1 green light being on Cleaning time: 0.5H 2 green lights being on Cleaning time: 1.0H 7 Cleaning mode AI Mode Error code 3 green lights being on Cleaning time: 2.0H*
All lights being off Cleaning until low battery Triangle green light in the floor being on Floor cleaning mode Both Triangle green lights being on Overall cleaning mode Floor, wall, waterline 1 green light being on Cleaning every 24 hours 2 green lights being on Cleaning every 48 hours 3 green lights being on Cleaning every 72 hours All lights being off Do not need AI Mode 1 2 3 4 5 6 Left drive failure Right drive failure Abnormal water pump Abnormal Control panel communication Infrared sensor anomalies Abnormal water sensor Battery light 1 green light being on Battery level: 20-50%
(Non-chargin 2 green lights being on Battery level: 50-75%
g status 3 green lights being on Battery level: 75-100%
Low battery 1 red light flashes Battery level: 15-20%
8 Battery light
(Charging status 1 green light flashes Battery level: 0-50%
1 green light being on, 1 green light flashes Battery level: 50-75%
2 green lights being on, 1 green light flashes Battery level: 75-100%
3 green lights being on Battery level: 100%
Green light flashes Network matching Signal light Green light on Network matched Red light flashes Failure Connection
*Note: If the cleaning time is set to be more than 2 hours via App, there will also be 3 lights on. 2.2 Operation on the display of the unit 1. Holding for 3 seconds to activate the device, then flashes, you can start setup the robot. After setup, press once* again for confirmation your settings. Then put the robot into the water, the robot will start cleaning automatically after it reaches to the floor. Please noted that if there is no operation on robot within 3 minutes as the in flashing status, the robot will shut down and enter into sleeping status.
*Note: There are 2 different situations when set up the AI Mode:
(Take set of " Cleaning every 24 hours" in AI Mode for example) a. If press once and then put the robot into the water, the robot will start work immediately. After once cleaning cycle, the robot will enter sleeping mode and 9 automatically wake up and work after 24 hours. b. If press for 3s and then put the robot into the water, the robot will enter sleeping mode at first. After 24 hours, it will start cleaning automatically. 2. If the battery is less than 15% during its cleaning, will keep flashing 1 red light, the robot will automatically go to the nearby poolside and shut down, then enter into sleep mode after 5 minutes. 2.3 Cleaning filter basket When cleaning is done, the robot will stop by the wall of pool. Please use the hook to catch the handle and lift the robot out of the water, then clean the filter basket as below operation:
Note:
There is a risk of being scratched by surface debris when cleaning the filter basket with your hands, it is recommended to wear rubber gloves for protection. 10 2.4 Charging the robot 1. Plug the adapter into power supply and make sure that indicator light is being red. 2. Open the cover of the robot's plug to expose the plug charging port. 3. Align the adapter plug post with the robot socket. When the robot is charging, the battery light of the robot flashes in green and the indicator light of the adapter is being on in red. 4. If battery light is full with 3 green lights on, and indicator light of the power adapter goes green, then the robot is fully charged. 5. Before charging, make sure charging port is dry. 6. It is recommended to disconnect the charger after charging completed to protect the battery. 11 7. If the robot needs to be stored for long time, it should be fully charged at least every three months to protect the battery. 8. It is not recommended to charge outdoors. Note: the robot must use original power adapter. 2.5 WIFI matching for the robot Hold for 3s, then the robot will have a beep sound, the robot enters matching mode, start flashing, then open the AI-BOT APP to search device and go matching, the robot will have three beep sounds and will be in green lights after matching done. After matching, setup of the robot can be operated by APP through Wifi or Bluetooth. Setup of the robot cannot be operated by APP if the robot is in the pool. (Due to the physical limitation of radio signal penetration in water). Note: download the AI-BOT APP in iOS App Store/ Google Play Store. 12 SECTION 3. MAINTENANCE WARNING 1. To avoid electric shock and other hazards which could result in major injuries, disconnect the adapter from the power source before performing any cleaning and maintenance. 13 2. Before any maintenance operation, be sure to insert back the magnetic cap at the bottom of the robot to avoid injuries caused by impeller rotation!
3.1 Filter maintenance 1. Clean the filter thoroughly and regularly for a better cleaning and climbing performance. Otherwise, the cleaning and climbing performance may be affected when the filter if full or clogged. 2. Clean the clogged filter with mild acidic detergent, and it is recommended to clean it at least once a year. 3.2 Impeller maintenance Visually check whether the impeller or impeller shaft is entangled with hair or other debris when the robot has a reduced suction or climbing performance, clean the debris trapped in the impeller.
* Magnetic cap MUST be inserted back before any operations on the impeller. 14 The steps are as follows:
Take out the filter box, remove the fixing screws of the inflow ring cover, and take out the inflow ring cover. Remove the deflector fixing screws and take out the deflector. Remove the impeller screw, then take out the impeller. (PS: impeller edge is sharp, please wear gloves while operating. Clean the impeller debris and reassemble the all the parts mentioned above in 15 order. PS: If you have any difficulties performing impeller maintenance, please contact your dealer for assistance. 3.3 Replace the worn brushes Remove the worn brushes and position the new brushes:
Remove the tabs from the holes inside which they are fastened, then remove the brushes. Fit the side without tabs under the brush holder. Roll the brush around its support, slide the tabs into the attachment holes and pull 16 on the end of each tab until its edge passes through the slit. 3.4 Replace the worn tracks Remove the worn tracks:
Position the new tracks:
17 SECTION 4. TROUBLE SHOOTING Failure Possible reason Solution Charging failure Debris on the electrode of charging head (Non-failure) Clean debris The bottom Magnetic cap isnt removed (Non-failure) Remove the Magnetic cap Charger is damaged Replace charger The Magnetic cap isnt removed
(Non-failure) Water spots on the robot Remove the Magnetic cap Switch on display or peoples hand Keep the display and hands dry, then try again failure
(Non-failure) Wrong operation (Non-failure) Hold the power button for 3 seconds No power in the battery
(Non-failure) Get the robot fully charged Not working Low battery (Non-failure) Get the robot fully charged not moving, not pumping Out of water (Non-failure) Make sure the robot under water and indicator lights being on 18 No pressing the on/off button Press the on/off button after the settings are done, after settings are done make sure indicator lights being on before putting
(Non-failure) the robot into water Full load of filter basket
(Non-failure) Clean filter basket Check whether there are too many debris in the guide ring, affecting the rotation of the impeller. The impeller gets stuck
(Please insert back the magnetic cap before operation, to avoid injuries caused by the impeller Moving but rotation. not pumping Full load of filter basket Clean filter basket
(Non-failure) Water inlet is blocked(Non-failure) Take out of filter basket and clean water inlet Battery low (Non-failure) Get the robot fully charged The moving motor gets stuck Please contact the dealer for replacement Track is deviated and stuck Turn the robot upside down and roll the track
(Non-failure) forward and backward to restore the track Pumping but not moving Track is damaged Replace track Scrubber gets stuck
(Non-failure) Clean scrubber The robot gets stuck by obstacle Remove obstacle and restart 19 and shut down for auto-protection (Non-failure) Full load of filter basket
(Non-failure) Under floor cleaning mode
(Non-failure) Clean filter basket Turn to overall cleaning mode Check whether there are too many debris in the guide ring, affecting the rotation of the impeller. The impeller is stuck
(Please insert back the magnetic cap before Not climbing operation, to avoid injuries caused by the impeller Full load of filter basket
(Non-failure) Water inlet is blocked
(Non-failure) rotation). Clean filter basket Take out of filter basket and clean the water inlet Battery low (Non-failure) Get the robot fully charged The impeller is stuck Remove any debris or hair in the guide ring Poor cleaning capability. Full load of filter basket
(Non-failure) Water inlet blocked
(Non-failure) Clean filter basket Take out of filter basket and clean water inlet. Scrubber is damaged Replace scrubber 20 Filter basket is damaged Replace filter basket Unusual non-stop Software failure Insert the magnetic cap back to bottom for 5s, then remove it and restart 21 Note:
1. Do not use the robot when people or animals are in the pool. 2. Charger MUST BE DISCONNECTED before conducting any maintenance on the robot. 3. Contact your dealer for problems not covered in Trouble Shooting Guide. 4. Normally, the robot will stop at the poolside when it encounters any failure or when the battery level is less than 15%. 5. In case of robot anomalies, the LED indicators on the control panel flash, and the Error Code will be displayed, please see chapter 2.1 to check the reason of malfunction. 6. By clicking the button or charging the robot, the Error Code may be cleared. If the Error Code cannot be cleared, please contact your dealer for technical support. Indoor Recycling For switch power supply indoor use only. When disposing the product, please hand it over to a designated 22 collection point for the recycling of waste electrical and electronic equipment. The separate collection and recycling of waste equipment at the time of disposal will help ensure that it is recycled in a manner that protects human health and the environment. For more information about where you can drop off your waste for recycling, please contact your local authority FCC Caution:
Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. IMPORTANT NOTE:
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. 23 This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 24 ISED Warning This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause undesired operation of the device. Lmetteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :
1) Lappareil ne doit pas produire de brouillage;
2) Lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptibleden compromettre le fonctionnement. This equipment complies with FCCs and ICs RF radiation exposure limits set forth For an uncontrolled environment. The antenna(s) used for this transmitter must be installed and operated to provide a separation distance of at least 20 cm from all persons and must not be collocated or operating in conjunction with any other antenna or transmitter. Installers must ensure that 20cm separation distance will be maintained between the device (excluding its handset) and users. 25 Cet appareil est conforme aux limites dexposition au rayonnement RF stipules par la FCC et lIC pour une utilisation dans un environnement non contrl. Les antennes utilises pour cet metteur doivent tre installes et doivent fonctionner au moins 20 cm de distance des utilisateurs et ne doivent pas tre places prs dautres antennes oumetteurs ou fonctionner avec ceux-ci. Les installateurs doivent sassurer quune distance de 20 cm spare lappareil ( lexception du combin) des utilisateurs. Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. Version: AX-FLR-A1 26
