Specifications Model Description MP-1311 Main System Processor Display Touch Panel Memory Storage Micro-SD Slot Communication Webcam Speaker Sensor I/O Interface USB Po-go Pin Peripherals Intel Atom x5-Z8350 Quad Core 1.44GHz, up to 1.92GHz 10.1-inch IPS, 1280 x 800, 300nits True-Flat Projected-Capacitive Multi Touch (PCAP) 4GB DDR3L 1600MHz 64GB eMMC Up to 128GB Wi-Fi IEEE 802.11 b/g/n, Bluetooth and GPS 2M Front Camera (FF) and 5M Rear Camera (AF) 2 x 0.8W Speakers Light Sensor, G Sensor and Gyroscope 1 x USB 3.0 Type A 1 x Pogo Pin (for charging and data transmission) External Modules Power Management Internal Battery Power Adapter Mechanical & Environmental MSR 2D Barcode Scanner Finger Print Lithium Polymer Battery 4800mAh 5V@3A 15W AC Power Adapter (option) Dimension Weight Operation System Certification Main Tablet : 310 (W) x 187.2 (H) x 25.9 (D) mm Dock Station : 220.5 (W) x 160.8 (H) x 125.8 (D) mm Main Tablet : 0.95kg (w/o accessories) Dock Station : 1.23kg (w/o power adapter) Windows 10 IoT Ent LTSB Entry EPKEA CE / FCC Class B Operation Condition 0C to +40C / 10 to 85% without condensation Charging Condition 0C to +40C / 10 to 85% without condensation Storage Condition
-10C to +50C / 10 to 85% without condensation MP-1311 10.1 Inch Mobile Point of System Quick Installation Guide IMPORTANT SAFETY INFORMATION Read following instructions carefully. Use only parts, especially power adapter, recommended by the manufacturer;
unapproved parts may be hazardous. Make sure that the voltage applied to the power outlet is within the specified range (100VAC ~240VAC). Improper power source voltage range will cause damage. Power off the system and remove the power adapter while cleaning the system. Before powering on the system, make sure all the peripherals are firmly installed. MP-1311 is required to be charged over 8 hours when used for the first time. Ver. 1.0 Copyright Fametech Inc. (TYSSO), 2019 Parts Descriptions A. Main Tablet Volume Up / Down Power Button MPOS Installation 1. Charge Your Tablet A. Power Adapter via Main Tablet B. Main Tablet via Charging Cradle Light Sensor LED Indicator Front Camera MSR Alignment Mark 5VDC Input Finger Print AC Power Adapter Pogo Pin
(to Dock Station or Charging Cradle) 2. Start Your POS System Dock Station or Charging Cradle 12VDC Input AC Power Adapter Rear Camera Hand Strap Press 3 Sec To Start the System:
Power Button To Shut Down the System:
BEEP!
Forced Shut Down:
10 Sec MP-1311 is required to be charged over 8 hours when used for the first time. 5VDC Input 2D Barcode Scanner Scan Trigger External Module Sku*
FCC Statement This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipmnet generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is lik ely to cause harmful required to correct the interference at his own expense. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference and
(2) this device must accept any interference received, including interference that may cause undesired operation. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. The transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.