FCC ID: T8I-CONEKT2 CONEKT MOBILE-READY CONTACTLESS SMARTCARD READER

QUICK START GUIDE CONEKT MOBILE-READY CONTACTLESS SMARTCARD READERS This Quick Start Guide is intended for experienced installing technicians. It is a basic reference to ensure all connections are properly made. Models include Conekt CSR-35, CSR-6.2 and CSR-6.4. For additional information please reference Farpointe Datas website www.farpointedata.com. 1.0 Introduction A key component of a physical security electronic access control system, a mobile-ready reader combining BLE and contactless smartcard technologies is based on RFID technology. In operation it is capable of reading data stored on a contactless smartcard credential via high frequencyor reading data from mobile credential stored in a smartphones wallet app via BLE technologyand without physical contact, and then passing the data obtained to the physical access control system. Access control systems typically manage and record the movement of individuals through a protected area, such as a locked door. 2.0 Mounting Provisions Each reader may be installed either indoors or outdoors. Mounting options shown in the table below. Use supplied #6 mounting screws, or equivalent security screws, for installation. CSR-35 CSR-6.2 CSR-6.4 Mullion Mount Single-gang Wall Mount*

*Plastic or metal. 3.0 Reader Wiring Red Black Green White Brown Orange Yellow Blue Violet Drain Ground Data 0 Data 1 Red LEDa Green LEDb Not Used Beeper Read Modec Shield Ground Red Black Green White Brown Orange Yellow Blue Violet Drain Ground Clock Data Red LED Green LED Not Used Beeper Read Mode Shield Ground Wiegand Magstripe aSingle Line LED: This is the standard operating mode and does not make use of the Conductor Function Conductor Function Orange conductor. The LED is Red when the reader is idle and flashes when a card is DC (8-14 VDC) DC (8-14 VDC) presented. The LED turns Green when the Brown Conductor is pulled low by the access NOTES:

control panel. bDual Line LED: This mode makes use of both the Brown and Orange conductors. The Brown conductor controls the Red LED and the Orange conductor controls the Green LED. LED states are determined by the access control system option and capability. cRead Mode: In regards to contactless smartcard credentials, the reader will only read and output the credentials Card Serial Number (CSN) when the Violet conductor is pulled low (connected to ground). Otherwise, the reader will only read and output the credentials programmed Sector data. Unused conductors should be trimmed, isolated and taped back to prevent unintended current flows. Apply positive voltage only to the Red DC Conductor. 4.0 Cable Requirements 24 AWG minimum, multi-conductor stranded with an overall foil shield, for example Belden 9535 or similar, supporting the five conductors comprising the physical layer of the Wiegand interface (power, ground, data 0, data 1, and/or beeper and LED). Alternatively, Belden 9539 or similar, for all reader functions. Contact your access control system manufacturer for their specific requirements. Per the SIAs Wiegand specification, maximum cable length is 500 feet (152 m). 5.0 Output Formats Wiegand (industry standard 26-bit Wiegand and custom Wiegand formats) Magnetic Stripe (ABA Track II, clock and data, with card present) 6.0 Grounding Shield (drain) continuity must run from the reader to the access panel. Shield (drain) and reader ground must be tied together at the access panel and connect to an earth ground at one point. 7.0 Power Reader may be powered by the access panel. A linear power supply is recommended for best operation. QUICK START GUIDE CONEKT MOBILE-READY CONTACTLESS SMARTCARD READERS 8.0 Voltage 8 to 14 VDC. 12 VDC at the reader is recommended for best operation. 9.0 Read Mode For sector data reads, do not connect the Violet conductor (leave it high). For CSN reads, pull the Violet conductor low (connect the Violet conductor to ground). 10.0 Connection Connection must be done in accordance with NFPA 70. Do not connect to a receptacle controlled by a switch. Connect to a power limited DC voltage source. 11.0 Troubleshooting 1. When the reader is first powered on it will beep 4-times, and the LED will shine red. 2. Presenting a supported access credential will result in the reader beeping and the LED flashing once. 3. Mobile operation is optimized for smartphones supporting BLE (Bluetooth LE) version 4.2 or newer. Further, for the downloading of mobile access credentials, a stable, high-quality internet connection is recommended. NOTE: The access panel controls LED functionality, such as switching the LED to green. If the reader does not recognize the mobile credential or card or tag (no beep, no LED flash) or exhibits short read range, please see the table below for possible causes and solutions. Possible Cause Incorrect cabling Not enough power Corrective Action Verify gauge, connections and cabling length 12 VDC recommended Incorrect credential used Verify if credential technology is supported Reader/access panel not properly grounded Earth ground neededverify shield and reader ground are tied at access panel and connect to ground at one point Supply generating interference Linear power supply recommended, verify switching power supply before use Should any of the corrective actions mentioned above not improve performance, disconnect the reader from the access panel and power it with a separate power supply or 9VDC battery, and re-test card functionality. By powering the readers separately, most variables that may lead to reduced performance can be eliminated. Should the problem persist, please contact Farpointe directly. Many Farpointe Data Readers carry the following certifications:

FCC Compliance Statement: This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Caution: Changes or modifications not expressly approved by Farpointe Data could void the user's authority to operate the equipment. Product can be used without license conditions or restrictions in all European Union coun-tries, including Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Poland, Portugal, Romania, Slovakia, Spain, Sweden, United Kingdom, as well as other non-EU countries, including Iceland, Norway, and Switzerland. This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device. Lmetteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes : (1) Lappareil ne doit pas produire de brouillage; (2) Lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. 0 2 7 0

. v e R 1 0 0

2 0 4 1 0

N P

Farpointe Data reserves the right to change specifications without notice. 2018-2020 Farpointe Data, Inc. All rights reserved. Farpointe Data, Pyramid Series Proximity, Delta, Ranger, and CONEKT are the registered U.S. trademarks of Farpointe Data, Inc. All other trademarks are the property of their respective owners. Farpointe Data, Inc. 2195 Zanker Road San Jose, CA 95131 USA Office: +1-408-731-8700 Fax: +1-408-731-8705 support@farpointedata.com www.farpointedata.com

Serial Number Label Specification Label P/N: 05566-001SCNSL Date: 29MAY2020 Product P/N: 05566-001SCN Rev.1 Label Stock:

Label 1.5" x 1.0" - REF: Quote Number Q261583 Genuine Zebra-Z-Ultimate 4000T White Polyester Label, 3" core, 5240 labels per roll. Dimensions: 1.5" wide x 1" long Ribbon - Part Number: 1150-00215 Zebra 5095 Performance Resin Ribbon Case, 1.57" x 1476 Ft. Usage: 3:1 Labels to Ribbon Serial Number Label Specification Label P/N: 05567-001SCNSL Date: 29MAY2020 Product P/N: 05567-001SCN Rev.1 Label Stock:

Label 1.5" x 1.0" - REF: Quote Number Q261583 Genuine Zebra-Z-Ultimate 4000T White Polyester Label, 3" core, 5240 labels per roll. Dimensions: 1.5" wide x 1" long Ribbon - Part Number: 1150-00215 Zebra 5095 Performance Resin Ribbon Case, 1.57" x 1476 Ft. Usage: 3:1 Labels to Ribbon

Farpointe Data Readers Credentials May 27, 2020 Federal Communications Commission 445 12" Street SW Washington, DC 20554 Subject: Limited Agency Agreement Farpointe Data, Inc. FCC ID: T8I-CONEKT2 To Whom It May Concern, We Farpointe Data, Inc., hereby authorize Intertek Testing Services to act as our Agent for the purpose of preparing the application for FCC ID number T8I-CONEKT2 under all applicable parts of the FCC rules and regulations. The effective date of this limited agency agreement is May 1, 2020. The Limited Agency Agreement expires on May 1, 2030, unless sooner terminated or extended by written notice to Intertek Testing Services and the Federal Communications Commission. This is to advise that we are in full compliance with the Anti-Drug Abuse Act. The applicant is not subject to a denial of federal benefits pursuant to Section 5301 of the Anti-Drug Act of 1988, 21 U.S.C.862, and no party to the application is subject to denial of federal benefits pursuant to that section. Sincerely, Kirk Bierach Director of Engineering Farpointe Data, Inc. 2195 Zanker Road, San Jose, CA 95131 USA +1-408-73 1-8700 www.farpointedata.com

Farpointe Data Readers = Credentials May 27, 2020 Attention: Application Examiner RE: Request for Confidentiality Applicant: Farpointe Data, Inc. FCC ID: T8I-CONEKT2 To Whom It May Concern:

Permanent Confidentiality Request is hereby submitted by Farpointe Data, Inc. to withhold permanently from public review certain portions of the application for equipment certification for the referenced FCC identifiers. This request for confidentiality is made pursuant to 47 CFR 0.457(d) and 0.459 of the FCC Rules. In particular, the following sections of the application are to be kept permanently confidential:

e Schematics e Detailed Block Diagrams e Detailed Operational/Functional Description e Parts list e Internal Photos (Circuit board covered with epoxy. Please see photos with and without epoxy. Farpointe Data, Inc. has invested considerable time and materials in research and development to produce the referenced product. Disclosure of the permanently confidential portions of this application to competitors would not only give them significant competitive advantages in developing similar products, but would also disclose successful implementation of unpublished, leading edge technology developed by us. The fee for confidentiality has been submitted along with the fee for certification.] If you have questions or need further information, please contact the undersigned. Sincerely, eb s /

Farpointe Data, Inc. Kirk Bierach 2195 Zanker Road San Jose, CA 95131 USA Director of Engineering Office: +1-408-731-8700 Fax: +1-408-731-8705 Farpointe Data, Inc. www.farpointedata.com