O BID i-scan Montageanleitung / Mounting Instruction ID ISC.MR100-A /
ID ISC.PR100-A
(deutsch / english) M10202-2de-ID-B.DOC Identifikation System OBID i-scan deutsche Version ab Seite 3 english version from page 19 H C S T U E D H S I L G N E Seite 2 von 34 FEIG ELECTRONIC GmbH Montageanleitung ID ISC.MR100-A / ID ISC.PR100-A H C S T U E D Ausgabe: cf/01/09/24 - m10202-2de-id-b.doc Copyright 2001 by FEIG ELECTRONIC GmbH Weitergabe sowie Vervielfltigung dieses Dokuments, Verwertung und Mitteilung ihres Inhalts sind nicht gestat-
tet, soweit nicht ausdrcklich zugestanden. Zuwiderhandlung verpflichtet zu Schadenersatz. Alle Rechte fr den Fall der Patenterteilung oder Gebrauchsmuster-Eintragung vorbehalten. Die Angaben in dieser Montageanleitung knnen ohne vorherige Ankndigung gendert werden. Alle frheren Ausga-
ben verlieren mit dieser Montageanleitung ihre Gltigkeit. Die Zusammenstellung der Informationen in dieser Montageanleitung erfolgt nach bestem Wissen und Gewissen. FEIG ELECTRONIC GmbH bernimmt keine Gewhrleistung fr die Richtigkeit und Vollstndigkeit der gemachten Angaben. Insbesondere kann FEIG ELECTRONIC GmbH nicht fr Folgeschden aufgrund fehlerhafter oder unvollstndiger An-
gaben haftbar gemacht werden. Die in diesem Handbuch gemachten Installationsempfehlungen gehen von gnstigsten Rahmenbedingungen aus. FEIG ELECTRONIC GmbH bernimmt keine Gewhr fr die einwandfreie Funktion einer OBID-Anlage in systemfremden Umgebungen. Da sich Fehler, trotz aller Bemhungen nie vollstndig vermeiden lassen, sind wir fr Hinweise jederzeit dankbar. FEIG ELECTRONIC GmbH bernimmt keine Gewhrleistung dafr, dass die in diesem Dokument enthaltenden Infor-
mationen frei von fremden Schutzrechten sind. FEIG ELECTRONIC GmbH erteilt mit diesem Dokument keine Lizenzen auf eigene oder fremde Patente oder andere Schutzrechte. OBID ist ein eingetragenes Warenzeichen der FEIG ELECTRONIC GmbH FEIG ELECTRONIC GmbH Seite 3 von 34 Identifikation System OBID i-scan H C S T U E D Europa (CE) Funkzulassungen Die Funkanlage entspricht, bei bestimmungsgemer Verwendung den grundlegenden Anforde-
rungen des Artikels 3 und den brigen einschlgigen Bestimmungen der R&TTE Richtlinie 1999/5/E6 vom Mrz 99. USA (FCC) FCC ID: PJMMR100-PR100 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation. Unauthorized modifications may void the authority granted under Federal communications Commission Rules permitting the operation of this device. ID ISC.MR100 :
Die Zulassung nach FCC 47 CFR CH. I Part 15 gilt im Zusammenhang mit der Antenne ID ISC.ANT340/240A. Seite 4 von 34 FEIG ELECTRONIC GmbH H C S T U E D Montageanleitung ID ISC.MR100-A / ID ISC.PR100-A Inhalt 1. Sicherheits- und Warnhinweise ................................................................................ 6 2. Leistungsmerkmale der Reader ................................................................................ 7 2.1 Leistungsmerkmale ........................................................................................................... 7 2.2 Verfgbare Readertypen.................................................................................................... 7 3. Montage und Anschlu .............................................................................................. 8 3.1 Spannungs- und Schnittstellenanschlu X2.................................................................... 8 3.2 Versorgungsspannung...................................................................................................... 9 3.3 Antennenanschlu X4 (nur ID ISC.MR100)..................................................................... 10 3.4 Asynchrone Schnittstelle ................................................................................................ 11 3.4.1 Schnittstellenkonfiguration mittels Jumper .................................................................. 11 3.4.2 RS232-Schnittstelle .................................................................................................... 12 3.4.3 RS485 Schnittstelle..................................................................................................... 13 3.4.4 Adresseinstellung fr Busbetrieb................................................................................. 13 4. Bedien- und Anzeigeelemente................................................................................. 14 4.1 LED.................................................................................................................................... 14 5. Technische Daten..................................................................................................... 15 6. Anhang ...................................................................................................................... 17 6.1 Zubehr ............................................................................................................................ 17 6.1.1 Serielles Datenkabel ID CAB.RS-A............................................................................. 18 6.1.2 Netzteil ID NET.12VDC............................................................................................... 18 FEIG ELECTRONIC GmbH Seite 5 von 34 H C S T U E D Identifikation System OBID i-scan 1. Sicherheits- und Warnhinweise Vor Inbetriebnahme unbedingt lesen !
Das Gert darf nur fr den vom Hersteller vorgesehenen Zweck verwendet werden. Die Bedienungsanleitung ist zugriffsfhig aufzubewahren und jedem Benutzer auszuhndigen. Unzulssige Vernderungen und die Verwendung von Ersatzteilen und Zusatzeinrichtungen, die nicht vom Hersteller des Gertes verkauft oder empfohlen werden, knnen Brnde, elektri-
sche Schlge und Verletzungen verursachen. Solche Manahmen fhren daher zu einem Aus-
schlu der Haftung und der Hersteller bernimmt keine Gewhrleistung. Fr das Gert gelten die Gewhrleistungsbestimmungen des Herstellers in der zum Zeitpunkt des Kaufs gltigen Fassung. Fr eine ungeeignete, falsche manuelle oder automatische Ein-
stellung von Parametern fr ein Gert bzw. ungeeignete Verwendung eines Gertes wird keine Haftung bernommen. Reparaturen drfen nur vom Hersteller durchgefhrt werden. Anschlu-, Inbetriebnahme-, Wartungs-, Messungs- und Einstellungsarbeiten am Gert drfen nur von Elektrofachkrften mit einschlgiger Unfallverhtungsausbildung erfolgen. Vor dem ffnen des Gertes ist stets die Versorgungsspannung abzuschalten und durch Nachmessen sicherzustellen, da das Gert spannungslos ist. Das Verlschen einer Betriebsanzeige ist kein Indikator dafr, da das Gert vom Netz ge-
trennt und spannungslos ist. Alle Arbeiten am Gert und dessen Aufstellung mssen in bereinstimmung mit den nationalen Bestimmungen und den rtlichen Vorschriften durchgefhrt werden. Der Benutzer ist dafr verantwortlich, da das Gert nach den anerkannten technischen Re-
geln im Aufstellungsland sowie anderen regionalen gltigen Vorschriften aufgestellt und ange-
schlossen wird. Dabei sind Kabeldimensionierung, Absicherung, Erdung, Abschaltung, Tren-
nung, Isolationsberwachung und der berstromschutz besonders zu bercksichtigen. Seite 6 von 34 FEIG ELECTRONIC GmbH H C S T U E D Montageanleitung ID ISC.MR100-A / ID ISC.PR100-A 2. Leistungsmerkmale der Reader 2.1 Leistungsmerkmale Der Reader ist fr das Lesen von passiven Datentrgern, sogenannten Smart Labels, mit einer Betriebsfrequenz von 13,56 MHz entwickelt worden. Der ID ISC.MR100 eignet sich fr alle Anwendungen, bei denen mittlere Lesereichweiten bentigt werden. Zustzlich wird noch eine externe Antenne bentigt, die an dem Reader angeschlossen werden mu. Der ID ISC.PR100 eignet sich fr alle Anwendungen, bei denen keine groen Lesereichweiten bentigt werden. Der Reader verfgt ber eine interne Antenne, so da keine externe Antenne bentigt wird. Eine Anticollision-Funktion ermglicht das gleichzeitige Lesen von bis zu 30 Transpondern pro Sekunde. Die Elektronik des Readers ist in einem Kunststoffgehuse untergebracht, welches die Schutzart IP30 besitzt. Der Reader verfgt ber eine asynchrone Schnittstelle, die wahlweise als RS232 oder RS485 konfiguriert werden kann. Durch die Konfigurierbarkeit der Schnittstelle kann der Reader auch am Datenbus mit RS485 Schnittstelle betrieben werden. Die Adresse des Readers kann dabei per Software vorgegeben werden. 2.2 Verfgbare Readertypen Folgende Reader sind z.Z. verfgbar:
Readertyp Beschreibung ID ISC.MR100-A Asynchrone Schnittstelle und externe Antenne ID ISC.PR100-A Asynchrone Schnittstelle und interne Antenne FEIG ELECTRONIC GmbH Seite 7 von 34 H C S T U E D Identifikation System OBID i-scan 3. Montage und Anschlu Der Reader ist fr die Broumgebung konzipiert. Es ist eine Wandmontage mglich. Der Wand-
montagesatz ist zustzlich zu bestellen. ( Siehe Anhang: 6.1 Zubehr). 3.1 Spannungs- und Schnittstellenanschlu X2 Zum Anschlu der Spannungsversorgung und der asynchronen Schnittstelle befindet sich auf der Leiterplatte ein 9-poliger D-Subminiatur-Steckverbinder (Buchse). Siehe auch Abbildung 3-1: Lei-
terplatte mit Jumpern und Anschlusteckern. X2 1 2 3 4 5 6 7 8 9 Schnittstelle
Spgsversorgung n.c. A-
B+
n.c. GND n.c. AGND n.c.
+12 V DC Tabelle 3-1: Anschlubelegung des Steckers X2 Fr den Reader ist ein serielles Datenkabel mit integriertem Spannungsanschlu erhltlich.
(Siehe 6.1 Zubehr und 6.1.1 Serielles Datenkabel ID CAB.RS-A). Feig Artikel Nr. 1690.000.00.00 Bezeichnung ID CAB.RS-A Tabelle 3-2: Serielles Datenkabel Seite 8 von 34 FEIG ELECTRONIC GmbH Montageanleitung ID ISC.MR100-A / ID ISC.PR100-A 3.2 Versorgungsspannung Die Versorgungsspannung von 12 V DC ist an der Klemme X2 der Leiterplatte anzuschlieen. Hinweis:
Eine Verpolung der Versorgungsspannung kann zur Zerstrung des Gertes fhren. H C S T U E D Klemme Kurzzeichen Beschreibung X2 / Pin 9 X2 / Pin 7
+12V AGND
+ 12 V DC Versorgungsspannung Ground Versorgungsspannung Tabelle 3-3: Anschlu der Versorgungsspannung Netzteilempfehlungen :
Zur Ausnutzung der vollstndigen Leistungsfhigkeit des Reader-Moduls sollte auf eine ausrei-
chend stabilisierte und rauschfreie Spannungsversorgung geachtet werden. Bevorzugt wird ein lineares Netzteil mit 12V DC / 580 mA. Bei der Verwendung eines Schaltnetzteils ist darauf zu achten, da die liegt.
(Siehe: 6.1 Zubehr und 6.1.2 Netzteil ID NET.12VDC). interne Schaltfrequenz des Netzteils unterhalb von 300 kHz Feig Artikel Nr. 1688.000.00.00 Bezeichnung ID NET.12VDC Tabelle 3-4: Empfohlenes Netzteil FEIG ELECTRONIC GmbH Seite 9 von 34 H C S T U E D Identifikation System OBID i-scan 3.3 Antennenanschlu X4 (nur ID ISC.MR100) Zum Anschlu der externen Antenne befindet sich auf der Leiterplatte eine SMA-Buchse. Das maximale Anzugsdrehmoment der SMA-Buchsen betrgt 0,45 Nm.
(Achtung: Hhere Anzugsdrehmomente fhren zur Zerstrung des Steckers.) Klemme X4 Beschreibung Anschlu der externen Antenne
(Eingangsimpedanz 50W
) Tabelle 3-5: Anschlu der externen Antenne Hinweise:
Die Eingangsimpedanz der Antenne ist auf einen Wert von 50 W (3 W 3) abzugleichen. Die optimale Betriebsgte der Antenne sollte im Bereich QB = 10...20 liegen. Zur Ermitt-
lung der Betriebsgte mu die Antenne mit einer 50W -Quelle, z.B. einem Network Analy-
zer oder einem Frequenzgenerator, versorgt werden. Fr das Erreichen optimaler Lesereichweiten sollte die Lnge der Antennenzuleitungen 3,6 m 0,1 m betragen. Beim Anschlu einer Antenne ist darauf zu achten, da diese die zulssigen Grenzwerte der nationalen Vorschriften bezglich Funkanlagen nicht berschreitet. Installation mit FCC Zulassung:
In Lnden, in denen eine FCC-Zulassung bentigt wird, darf der Reader nur mit den in Tabelle 3-6 aufgefhrten Antennen in Betrieb genommen werden. Aufgrund von nderungen oder Modifi-
zierungen, die nicht ausdrcklich von der zustndigen Zulassungsbehrde genehmigt wurden, kann die Betriebserlaubnis des Anwenders erlschen. Artikel Nr. Bezeichnung 1663.000.00.00 ID ISC.ANT340/240 Tabelle 3-6: Antennen mit FCC Zulassung Die Anschlu-, Inbetriebnahme-, Wartungs-, Messungs- und Einstellungsarbeiten am Gert drfen nur von Elektrofachkrften oder Personen mit quivalenter Ausbildung erfolgen. Seite 10 von 34 FEIG ELECTRONIC GmbH Montageanleitung ID ISC.MR100-A / ID ISC.PR100-A 3.4 Asynchrone Schnittstelle Die asynchrone Schnittstelle kann wahlweise als RS485 oder RS232 konfiguriert werden. Hinweis:
Der gleichzeitige Betrieb von RS232 und RS485 Schnittstelle ist nicht mglich. H C S T U E D 3.4.1 Schnittstellenkonfiguration mittels Jumper 4 7 J 7 7 J 3 7 J 1 1 2 J 2 7 J X2 3 2 J 4 2 J X4 1 2 3 4 5 6 7 8 9 Abbildung 3-1: Leiterplatte mit Jumpern und Anschlusteckern ber den Jumper J21 kann die asynchrone Schnittstelle als RS232- oder RS485-Schnittstelle konfiguriert werden. Jumper J21 RS232 1 - 2 RS485 2 - 3 Tabelle 3-7: Konfiguration RS232/RS485 Schnittstelle FEIG ELECTRONIC GmbH Seite 11 von 34 H C S T U E D Identifikation System OBID i-scan Im Fall der RS485-Schnittstelle knnen die eventuell bentigten Abschluwiderstnde mit den Jumpern J73, J74 und J77 zugeschaltet werden. Jumper geschlossen offen J73 J74 J77 Pull-Up an RS485 - B ohne Pull-Up an RS485 - B Pull-Down an RS485 - A ohne Pull-Down an RS485 - A Abschluwiderstand RS485 - A RS485 - B ohne Abschluwiderstand RS485 - A RS485 - B Tabelle 3-8: Konfiguration RS485 Schnittstelle J73 J77 J74 RS485 - B+
RS485 - A-
Abbildung 3-2: Jumper der RS485 Schnittstelle 3.4.2 RS232-Schnittstelle Der Anschlu der RS232-Schnittstelle erfolgt ber X2. Die bertragungsparameter knnen per Softwareprotokoll konfiguriert werden. Anschlubelegung X2 (RS232-Schnittstelle):
Klemme Kurzzeichen Beschreibung 2 3 5 TxD RxD GND RS232 TxD RS232 RxD RS232 GND Tabelle 3-9: Anschlubelegung der RS232 Schnittstelle Seite 12 von 34 FEIG ELECTRONIC GmbH H C S T U E D Montageanleitung ID ISC.MR100-A / ID ISC.PR100-A 3.4.3 RS485 Schnittstelle Der Anschlu der RS485-Schnittstelle erfolgt ber X2. Die bertragungsparameter knnen per Softwareprotokoll konfiguriert werden. Anschlubelegung X2 (RS485-Schnittstelle):
Pin Kurzzeichen Beschreibung 2 3 5 A-
B+
GND RS485 (A -) RS485 (B +) RS485 GND Tabelle 3-10: Anschlubelegung der RS485 Schnittstelle 3.4.4 Adresseinstellung fr Busbetrieb Fr den Busbetrieb bietet der Reader die Mglichkeit die bentigte Busadresse per Software zu vergeben. Die Adressvergabe erfolgt ber den Host-Rechner. Mit Hilfe der Software knnen dem Reader die Adressen "0" bis "254" zugewiesen werden. Hinweis:
Da alle Reader werksseitig die Adresse 0 eingestellt haben, mssen sie nacheinander an-
geschlossen und konfiguriert werden. FEIG ELECTRONIC GmbH Seite 13 von 34 H C S T U E D Identifikation System OBID i-scan 4. Bedien- und Anzeigeelemente 4.1 LED Die LED des Readers kann per Software konfiguriert werden. Tabelle 4.1-1 zeigt die Standard-Konfiguration der LED. Kurzzeichen LED grn LED rot Beschreibung
"RUN "
- Signalisiert den ordnungsgemen Ablauf der internen Reader-Software. Leuchet, wenn der Reader betriebsbereit ist.
LABEL
Leuchtet, wenn ein Label erkannt wird. LED orange INITIALISIERUNG
- Blinkt whrend der Reader-Initialisierung nach dem Einschal-
ten. Tabelle 4.1-1: Standard-Konfiguration der LED Seite 14 von 34 FEIG ELECTRONIC GmbH H C S T U E D Montageanleitung ID ISC.MR100-A / ID ISC.PR100-A 5. Technische Daten Mechanische Daten Gehuse Kunststoff ABS geschlossen Abmessungen ( B x H x T ) 85 x 145 x 31 mm Gewicht Schutzart Farbe 200 g IP 30 RAL 9018 Elektrische Daten Spannungsversorgung Leistungsaufnahme Betriebsfrequenz Sendeleistung Antennenanschlu
(nur ID ISC.MR100) Schnittstellen typisch 12 V DC max. Spannungsbereich 12 24 V DC 15 %
ID ISC.MR100: max. 8 VA ID ISC.PR100: max. 5 VA 13,56 MHz ID ISC.MR100: 1,0 W ID ISC.PR100: 0,5 W SMA Buchse (50W
) RS232 und RS485 (wahlweise einstellbar) Funktionelle Eigenschaften Untersttzte Transponder ICode1, Tag-it-HF, ISO 15693 Adreeinstellung fr Schnittstelle Software (bis zu 254 Adressen) Signalgeber optisch 1 LED ( mehrfarbig rot / grn) FEIG ELECTRONIC GmbH Seite 15 von 34 Identifikation System OBID i-scan H C S T U E D Umgebungsbedingungen Temperaturbereich
- Betrieb
- Lagerung Angewendete Normen Zulassung Funk
- Europa
- USA EMV Sicherheit
- Europa
-25C bis +60C
-25C bis +70C EN 300 330 FCC 47 CFR Part 15 EN 300 683 EN 60950 Seite 16 von 34 FEIG ELECTRONIC GmbH 6. Anhang 6.1 Zubehr Montageanleitung ID ISC.MR100-A / ID ISC.PR100-A H C S T U E D Zu dem Reader ist folgendes Zubehr zu erhalten. Artikel Nr. 1688.000.00.00 Bezeichnung ID NET.12VDC 1690.000.00.00 ID CAB.RS-A Beschreibung 12 V DC Netzteil mit passendem Stecker fr ID CAB.RS-A. Serielles Datenkabel mit integrierter Ver-
sorgungsleitung 1691.000.00.00 ID ISC.MS.MR/PR-A Wandmontagesatz fr 1687.000.00.00 ID CO.RS232/485 1663.000.00.00 ID ISC.ANT340/240 1451.000.00.01 ID ISC.ANT300/300 ID ISC.MR100 und ID ISC.PR100. Externer RS232/RS485 Umsetzer Externe Antenne Abm.:
Schutzart.:
340mm x 240mm x 9mm IP30 Externe Antenne Abm.:
Schutzart.:
300mm x 300mm x 30mm IP65 FEIG ELECTRONIC GmbH Seite 17 von 34 H C S T U E D Identifikation System OBID i-scan 6.1.1 Serielles Datenkabel ID CAB.RS-A PC:
9-pol D-Sub Buchse Versorgung:
DC-Kupplung 2,5mm*5,5mm Reader:
9pol. D-Sub Stecker Abbildung 6-1: Serielles Datenkabel mit Spannungsanschlu
+ 12 V DC AGND Abbildung 6-2: Belegung der DC-Kupplung 6.1.2 Netzteil ID NET.12VDC Bei dem Netzteil mu noch der Kupplungsteil mit der korrekten Polaritt auf das Netzteil gesteckt werden. Achtung: Der Kupplungsteil ist nicht mehr abtrennbar, wenn er einmal eingerastet ist !
Eine Verpolung kann zur Zerstrung des Gertes fhren. minus - auen AGND plus - innen
+12 V DC Abbildung 6-3: Polaritt der Kupplung Seite 18 von 34 FEIG ELECTRONIC GmbH Mounting Instruction ID ISC.MR100-A H S I L G N E _________ Edition: cf/01/09/24 - m10202-2de-id-b.doc Copyright 2001 by FEIG ELECTRONIC GmbH Copying of this document, and giving it to others and the use or communication of the contents thereof are forbidden without express authority. Offenders are liable to the payment of damages. All rights are reserved in the event of the grant of a patent or the registration of a utility model or design. Indications made in this manual may be changed without previous notice. With the edition of this manual, all previous editions become void. Composition of the information in this manual has been done to the best of our knowledge. FEIG ELECTRONIC GmbH does not guarantee the correctness and completeness of the details given in this manual and may not be held liable for damages ensuing from incorrect or incomplete information. Since, despite all our efforts, errors may not be completely avoided, we are always grateful for your useful tips. The installation instructions given in this manual are based on advantageous boundary conditions. FEIG ELECTRONIC GmbH does not give any guarantee promise for perfect function of an OBID-system in cross surroundings. FEIG ELECTRONIC GmbH assumes no responsibility for the use of any information contained in this manual and makes no representation that they free of patent infringement. FEIG ELECTRONIC GmbH does not convey any license under its patent rights nor the rights of others. OBID is a registered trademark of FEIG ELECTRONIC GmbH. FEIG ELECTRONIC GmbH Page 19 of 34 Identifikation System OBID i-scan Type approval Europe (CE) When used according to regulation, this radio equipment conforms with the basic requirements of Article 3 and the other relevant provisions of the R&TTE Guideline 1999/E6 dated March 99. H S I L G N E USA (FCC) FCC ID: PJMMR100-PR100 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation. Unauthorized modifications may void the authority granted under Federal communications Commission Rules permitting the operation of this device. ID ISC.MR100:
Approval per FCC 47 CFR CH. I Part 15 applies to use with the antenna ID ISC.ANT340/240. Page 20 of 34 FEIG ELECTRONIC GmbH Mounting Instruction ID ISC.MR100-A Contents 1. Safety Instructions / Warning .................................................................................. 22 H S I L G N E 2 Performance Features of the Reader...................................................................... 23 2.1 Performance features ...................................................................................................... 23 2.2 Available Reader-Types................................................................................................... 23 3 Assembly and Wiring ............................................................................................... 24 3.1 Power and interface terminal X2..................................................................................... 24 3.2 Supply voltage.................................................................................................................. 25 3.3 Antenna terminal X4 (only ID ISC.MR100) ...................................................................... 26 3.4 Asynchronous interface .................................................................................................. 27 3.4.1 Interface configuration using jumpers ......................................................................... 27 3.4.2 RS232 interface .......................................................................................................... 28 3.4.3 RS485 interface .......................................................................................................... 29 3.4.4 Setting the address for bus mode ............................................................................... 29 4 Control and Display Elements................................................................................. 30 4.1 LED.................................................................................................................................... 30 5 Technical Data .......................................................................................................... 31 6 Appendix ................................................................................................................... 33 6.1 Accessories...................................................................................................................... 33 6.1.1 Serial data cable ID CAB.RS-A ................................................................................... 34 6.1.2 Power supply ID NET.12VDC ..................................................................................... 34 FEIG ELECTRONIC GmbH Page 21 of 34 Identifikation System OBID i-scan 1. Safety Instructions / Warning Please read before startup !
H S I L G N E The device may be used only for the purpose intended by the manufacturer. The Mounting Instruction should be kept in an accessible location and handed out to every user and maintenance person. Non-approved modifications and the use of replacement parts and accessories which have not been purchased or recommended by the manufacturer of the device may cause fires, electrical shocks and injury. This will furthermore result in exclusion of liability and loss of warranty on the part of the manufacturer. The warranty conditions in effect at the time of purchase shall be considered valid. No liability is assumed for inappropriate, improper manual or automatic setting of parameters for a device or for improper use of a device. Repairs are to be performed only by the manufacturer. Hookup, startup, maintenance, measuring and calibration work on the device must be per-
formed only by electrical specialists who have received the relevant accident prevention train-
ing. Before opening the device always turn off the supply voltage and use a test instrument to verify that the device is unpowered. The fact that the indicator lamp is off does not necessarily mean that the device has been dis-
connected from the power supply or that it is without power. All work on the device including installation must be in conformance with national electrical regulations as well as with local code. The user has to make sure that the appliance is installed and operated according to the tech-
nical rules of the country of installation as well as other regional regulations. Cable dimensions, protection, earthing, disconnection, insulation control and excess current protection should be especially considered. Page 22 of 34 FEIG ELECTRONIC GmbH Mounting Instruction ID ISC.MR100-A 2 Performance Features of the Reader 2.1 Performance features The Reader is designed for reading passive data carriers, so-called Smart Labels at an operating frequency of 13.56 MHz. The reader ID ISC.MR100 is suitable for all applications in which moderate reading distances are required. Also required is an external antenna connected to the Reader. H S I L G N E The ID ISC.PR100 is suitable for all applications which dont require wide reader ranges. The reader contains of an internal antenna, so that is no external antenna necessary. An anti-collision function enables simultaneous reading of up to 30 transponders per second. The Reader electronics is contained in a plastic housing having an IP30 enclosure rating. The Reader comes with an asynchronous port which can be configured for RS232 or RS485. The ability to configure the port means that the Reader can also be operated on a databus with RS485 interface. The address of the Reader is configured via software. 2.2 Available Reader-Types Following Reader-Types are available at present:
Reader-Types Description ID ISC.MR100-A asynchronous interface and external antenna ID ISC.PR100-A asynchronous interface and internal antenna FEIG ELECTRONIC GmbH Page 23 of 34 Identifikation System OBID i-scan 3 Assembly and Wiring The Reader is designed for an office environment. It can be wall-mounted, in this case the wall-
mount kit should be ordered separately. ( see Appendix: 6.1Accessories). H S I L G N E 3.1 Power and interface terminal X2 A 9-pin D-sub female socket is located on the circuit board for connecting the supply voltage and asynchronous interface. See also Fig. 3-1: Circuit board with jumpers and sockets. X2 1 2 3 4 5 6 7 8 9 Interface
Supply voltage n.c. A-
B+
n.c. GND n.c. AGND n.c.
+12 V DC Table 3-1: Pin configuration X2 A serial data cable with integrated power connection is available for the Reader.
(see 6.1 Accessories and 6.1.1 Serial data cable ID CAB.RS-A). Feig Article No. 1690.000.00.00 Part No. ID CAB.RS-A Table 3-2: Serial data cable Page 24 of 34 FEIG ELECTRONIC GmbH Mounting Instruction ID ISC.MR100-A 3.2 Supply voltage Connect the 12 V DC supply voltage to terminal X2 on the circuit board. Note:
Reversing the polarity of the supply voltage may destroy the device. Terminal Name Description X2 / Pin 9 X2 / Pin 7
+12V AGND
+ 12 V DC supply voltage Ground supply voltage Table 3-3: Connecting the supply voltage H S I L G N E Power supply recommendations :
To take full advantage of the Reader module performance, you must use a sufficiently regulated and noise-free power supply. Preferred is a linear power supply with 12V DC / 580 mA. When us-
ing a switching power supply, be sure that its internal switching frequency is less than 300 kHz.
(see: 6.1 Accessories and 6.1.2 Power supply ID NET.12VDC). Feig Article No. 1688.000.00.00 Part No. ID NET.12VDC Table 3-4: Recommended power supply FEIG ELECTRONIC GmbH Page 25 of 34 Identifikation System OBID i-scan 3.3 Antenna terminal X4 (only ID ISC.MR100) An SMA socket is provided on the circuit board for connecting the external antenna. The maximum tightening torque for the SMA socket is 0.45 Nm.
(Caution: Higher tightening torque will damage the connector.) H S I L G N E Terminal Description X4 Connecting the external antenna
(input impedance 50W
) Table 3-5: Connecting the external antenna Note:
The input impedance for the antenna should be calibrated to a value of 50 W (3 W 3). The optimum operating Q factor of the antenna should be in a range of Qoper = 10...20. To determine the operating Q the antenna must be supplied with a 50 Ohm source such as a network analyzer or frequency generator. To achieve optimum read distances, the length of the antenna lines should not exceed 3.6 m 0.1 m. When connecting an antenna, ensure that it does not exceed the permissible limits pre-
scribed by the national regulations for radio frequency devices. Installation with FCC Approval:
In countries where FCC approval is required, the ID ISC.MR100 Reader may only be operated using the antennas listed in Table 3-6. Changes or modifications not expressly authorized by the relevant approval body may result in revocation of the users operating permission. Article No. Part No. 1663.000.00.00 ID ISC.ANT340/240 Table 3-6: Antennas with FCC Approval Electrical connection, commissioning, maintenance, measurement and calibration work on the unit is to be performed only by electrical specialists or persons with equivalent training. Page 26 of 34 FEIG ELECTRONIC GmbH Mounting Instruction ID ISC.MR100-A 3.4 Asynchronous interface The asynchronous interface can be configured as either RS232 or RS485. Note:
It is not possible to run both RS232 and RS485 at the same time. 3.4.1 Interface configuration using jumpers H S I L G N E 4 7 J 7 7 J 3 7 J 1 1 2 J 2 7 J X2 3 2 J 4 2 J X4 1 2 3 4 5 6 7 8 9 Fig. 3-1: Circuit board with jumpers and sockets Jumper J21 is used to configure the asynchronous interface as RS232 or RS485. Jumper J21 RS232 1 - 2 Table 3-7: Configuring as RS232/RS485 RS485 2 - 3 FEIG ELECTRONIC GmbH Page 27 of 34 Identifikation System OBID i-scan In the case of the RS485 configuration, the termination resistors which may be required can be inserted using jumpers J73, J74 and J77. Jumper in out J73 J74 J77 Pull-Up on RS485 - B out Pull-Up on RS485 - B Pull-Down on RS485 - A out Pull-Down on RS485 - A Termination resistor RS485 - A RS485 - B no termination resistor RS485 - A RS485 - B Table 3-8: Configuring the RS485 interface H S I L G N E J73 J77 J74 RS485 - B+
RS485 - A-
Fig. 3-2: Jumper of the RS485 interface 3.4.2 RS232 interface The RS232 interface is connected through X2. The transmission parameters can be configured using software protocol. Pin assignments X2 (RS232 interface):
Terminal Abbrev. Description 2 3 5 TxD RxD GND RS232 TxD RS232 RxD RS232 GND Table 3-9: Wiring assignments for the RS232 Page 28 of 34 FEIG ELECTRONIC GmbH Mounting Instruction ID ISC.MR100-A 3.4.3 RS485 interface The RS485 interface is connected through X2. The transmission parameters can be configured using software protocol. Pin assignments X2 (RS485 interface):
Pin Abbrev. Description 2 3 5 A-
B+
GND RS485 (A -) RS485 (B +) RS485 GND Table 3-10: Wiring assignments for the RS485 interface H S I L G N E 3.4.4 Setting the address for bus mode For bus operation the Reader can be assigned a bus address using software. Addresses are assigned by the host computer. Using the software, addresses 0 to 254 can be assigned to the Reader. Note:
Since all Readers are factory set with Address 0, you must connect and configure them one after the other. FEIG ELECTRONIC GmbH Page 29 of 34 H S I L G N E Identifikation System OBID i-scan 4 Control and Display Elements 4.1 LED The Readers LED can be configured through software. Table 4.1-1 shows the standard configuration of the LED. Abbreviation LED green LED red Description
"RUN "
LABEL Indicates the Reader software is running properly. Turns on when the Reader is ready.
Turns on when a label is detected. LED orange INITIALIZING
Flashes during Reader initialization after power-up. Table 4.1-1: Standard configuration of the LEDs Page 30 of 34 FEIG ELECTRONIC GmbH H S I L G N E Mounting Instruction ID ISC.MR100-A 5 Technical Data Mechanical Data Housing ABS plastic Enclosed Dimensions (W x H x D) 85 x 145 x 31 mm Weight Enclosure rating Color Electrical Data Supply voltage Power consumption Operating frequency Transmitting power Antenna connection
(only ID ISC.MR100) Interfaces Functional properties 200 g IP 30 RAL 9018 typical. 12 V DC max. voltage range 12 24 V DC 15 %
ID ISC.MR100:
ID ISC.PR100:
13.56 MHz max. 8 VA max. 5 VA ID ISC.MR100:
ID ISC.PR100:
SMA female (50W
) 1,0 W 0,5 W RS232 and RS485 (configurable) Supported transponders ICode1, Tag-it-HF, ISO 15693 Address setting for interface Software (up to 254 addresses) Visual indicators 1 LED ( multicolor red / green) FEIG ELECTRONIC GmbH Page 31 of 34 Identifikation System OBID i-scan H S I L G N E Ambient conditions Temperature range
- Operation
- Storage Applicable Norms Radio approval
- Europe
- USA EMC Safety
- Europe
-25C to +60C
-25C to +70C EN 300 330 FCC 47 CFR Part 15 EN 300 683 EN 60950 Page 32 of 34 FEIG ELECTRONIC GmbH Mounting Instruction ID ISC.MR100-A 6 Appendix 6.1 Accessories H S I L G N E The following accessories are available for the Reader. Article No. Part No. Description 1688.000.00.00 ID NET.12VDC 1690.000.00.00 ID CAB.RS-A 12 V DC power supply with suitable con-
nector for ID CAB.RS-A Serial data cable with integrated supply voltage line 1691.000.00.00 ID ISC.MS.MR/PR-A Wall mounting kit for 1687.000.00.00 ID CO.RS232/485 1663.000.00.00 ID ISC.ANT340/240 1451.000.00.01 ID ISC.ANT300/300 ID ISC.MR100. and ID ISC.PR100. External RS232/RS485 converter External antenna Dimensions: 340mm x 240mm x 9mm Enclosure rating.:
IP30 External antenna Dimensions: 300mm x 300mm x 30mm Enclosure rating.:
IP65 FEIG ELECTRONIC GmbH Page 33 of 34 Identifikation System OBID i-scan 6.1.1 Serial data cable ID CAB.RS-A PC:
9-pin D-sub female Supply:
DC adapter 2.5mm*5.5mm Reader:
9-pin D-sub male H S I L G N E Fig. 6-1: Serial data cable with supply voltage connection
+ 12 V DC AGND Fig. 6-2: DC adapter configuration 6.1.2 Power supply ID NET.12VDC The AC adapter must be plugged into the power supply while observing the correct polarity. Caution:
The AC adapter can no longer be unplugged once it has been inserted !
Reversing the polarity may destroy the device. minus - outside AGND plus - inside
+12 V DC Fig. 6-3: Polarity of the adapter Page 34 of 34 FEIG ELECTRONIC GmbH