FCC ID: SYW-FLR42RGBBK FLOOR42/RGB/BLK/AG

FCC Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation. Warning: Any Changes or modications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:

(1) Reorient or relocate the receiving antenna.

(2) Increase the separation between the equipment and receiver.

(3) Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.

(4) Consult the dealer or an experienced radio/TV technician for help. FCC Radio Frequency Exposure Statement The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be collocated or operating in conjunction with any other antenna or transmitter, End-Users must be provided with transmitter operation conditions for satisfying RF exposure compliance. IC Statement This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:

(1) this device may not cause interference, and

(2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes:

(1) l'appareil nedoit pas produire de brouillage, et

(2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numrique de la classe B est conforme la norme NMB-003 du Canada. IC RF Statement:

When using the product, maintain a distance of 20cm from the body to ensure compliance with RF exposure requirements. Lors de l'utilisation du produit, maintenez une distance de 20 cm du corps an de vous conformer aux exigences en matire d'exposition RF.

25 mm

65 mm 160 mm 80 mm 80 mm

FRONT 160 mm 80 mm 80 mm 25 mm BACK Label Location Label Location The adapter label 29 mm 260-21-50 24 mm 5009611 Made in China

Ningbo Sunpu Led Co.,Ltd Federal Communications Commission, Date: February 18, 2022 Authorization & Evaluation Division, 7435 Oakland Mills Road, Columbia, MD. 21046 Attention: Equipment Authorization Branch CHANG IN IDENTIFICATION OF EQUIPMENT We, Ningbo Sunpu Led Co.,Ltd , declare on our sole responsibility that FEIT ELECTRIC CO,INC may apply Change in FCC Identifier as established in 47CFR2.933(b) for currently approved devices listed below. FCC ID: 2A3ZE-FLD20X11 Regards, Signed by original applicant V1.0

LECTIIC Manufacturers of Light Bulbs FEIT ELECTRIC COMPANY 4901 Gregg Road Pico Rivera, CA 90660

(862) 463-BULB (2852) Date: March 10, 2022 (800) 543-FEIT (3348) Federal Communications Comission, Authorization & Evaluation Division, 7435 Oakland Mills Road, Columbia, MD. 21046 Attention: Equipment Authorization Branch CHANG IN IDENTIFICATION OF EQUIPMENT We, FEIT ELECTRIC COMPANY , request to apply for a new FCC ID as established in 47CFR 2.933(b) for a currently approved device. This application will establish a new FCC ID: SYW-FLR42RGBBK. Per 2.933(b) 41. The original identification is FCC ID: 2A3ZE-FLD20X11 2. The original grant date is January 20,2022 ;

3. The equipment is electrically identical. There is no change in design, circuitry or construction, 4. The original test results are applicable and representative of this changed device. 5. Exterior photographs are included in this application. External photos with label location and type label sample drawing are electronically submitted as attachments. Sincerely, Signed by new applicant Vi.0

LECTIVIE Manufacturers of Light Bulbs FEIT ELECTRIC COMPANY 4901 Gregg Road Pico Rivera, CA 90660

(662) 463-BULB (2852)

(800) 543-FEIT (3348) Fax: (562) 908-6360 E-mail: info@feit.com Authority to Act as Agent wy feit.com Date: March 10, 2022 American Certification Body, Inc. 6731 Whittier Avenue Suite C110 McLean, VA 22101 To Whom It May Concern:

Intertek Testing Service Shanghai is authorized to act on our behalf, until otherwise notified, for applications to American Certification Body, Inc. (ACB). We certify that we are not subject to denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Further, no party, as defined in 47 CFR 1.2002 (b), to.the-application is-subject-to.denial.of federal.benefits,-that-includes.ECC benefits. We also declare that the information provided to the FCC is true and correct to the best of our knowledge (47 CFR 2.911(d)) and we have been informed of the grantee responsibilities (47 CFR 2.909) with regard to certified equipment. Thank you, Agency Agreement Expiration Date: February 31, 2023 By: Aaron Feit

(Sigyfature) (Print name) Title: Chief Executive Officer On behalf of: FEIT ELECTRIC COMPANY

(Company Name) Telephone: (562) 463-2852

'_ Must be signed by applicant contact given for applicant on the FCC site, or by the authorized agent if an approprlate authorized agent letter has been provided, Letters should be placed on appropriate letterhead. 041521-14