FCC ID: 2A7JJWFJH103 Automatic drip Irrigation kit

Instructions for WiFi Intelligent Double-path watering device This manual only applies to WD-01ADE. Please read the instructions carefully before using the product. Connection method Operation process Download app Download app registration&login connection device setting parameters Search "ewelink" by mobile phone, download and install the app. Users in the mainland of China can register with their mobile phone numbers, while users in other regions can register and log in by email. If you have already registered an e-micro account, you can enter your account to log in. registration&login connection device Power on the watering device and keep it in the same WiFi signal with the mobile phone, and ensure that the WiFi is 2.4GHz. At this time, the blue signal indicator lights up, and different flashing modes represent different states, as follows:

2short and 1 long: pairing mode continuous flash: compatible pairing mode slow flash: offline / unconnected normally on: Networking When the unpaired device is powered on, it is in pairing mode by default (2 short and 1 long). Long press any setting button for 5 seconds to switch to compatible pairing mode (continuous flash); when offline (slow flash), long press any setting button for 5 seconds to enter pairing mode (2 short and 1 long). Select add a device Device addition complete Product introduction WD-

Thank you for choosing the WiFi dual-way automatic flower sprayer produced by our company. This product has a novel appearance, suitable for home, office and other scenarios; Selected high quality ABS+PP raw materials, anti-brittle cracking oxidation performance is good. The product is developed based on the Internet of Things platform. It is connected to WiFi and can be controlled remotely after setting through mobile APP. You can set the watering time and frequency in the APP according to your needs. The chip has built-in clock function, and the flower sprayer will also work on time according to your setting when offline. This product is equipped with domestic famous brand miniature diaphragm pump, with high efficiency, low noise, small vibration, high suction, high head, long life and many other advantages. 4 AA batteries and adapter dual-mode uninterrupted power supply, high quality WIFI module with SMT process control module, safe and reliable, let you easily, carefree. Function introduction When you click Set / MA, pump a will run manually; when you click Set / MB, pump B will run manually; long press the key for 5 seconds to switch the matching mode. Product parameters Rated voltage5 V Size 83*83*95L*W*H) Lift 2.5 m Rated current720 mA net weight 240g Suction2m Power3.6 W Body material: >ABS< Wifi: 2.4GHz Connection caliber 4.8 mm Water pipe4/6 ,4/7 Maximum pressure:30psi(200kpa) Battery model 4-AA 1.5v Water flow0.3-0.8 LPM AdapterDC 5V 2A DC002 3.5/1.3 Noise range65 db(30cm Ambient temperature0-50 Enter app, click + to add device. Choose quick add Select the WiFi you want to connect to and enter the password Make sure the device is in pairing mode (2 short and 1 long) Please note that 1.The mobile phone and flower watering device should be close to the router as far as possible to obtain stronger WiFi signal; WiFi must be 2.4GHz. 2. During pairing, please make sure that the device is in pairing mode (signal light status is 2 short and 1 long). If it is not in pairing mode, you can press any key for 5 seconds to switch modes. 3. In case of pairing failure, please check the software permission settings to ensure that the app has WiFi and location access rights. 4. Pairing always fails. Please try compatible pairing mode. compatible pairing mode When pairing mode fails to connect normally, you can select compatibility mode to connect. When connecting, please adjust the matching mode of flower watering device to "compatible matching mode", and the signal indicator light is continuous flash. At this time, according to the hot spot name and password prompted by the mobile phone, select to connect to the hot spot. In the pop-up dialog box, allow ewelink to join WLAN. Pumb A working time Pumb B working time Timing scheme setting click the timing icon --- add a new timing scheme --- select time, date and channel (action mode is open) -- please click save after setting. Hotspot name and password After adding, click here to modify the device name Click compatibili ty mode Select this device hotspot Click timing Device addition complete Please note that setting parameters After adding the device, click to enter the device to set the working time and frequency of the flower watering device according to your needs. plugging in and out. Watering working time setting: enter the equipment interface --- click option setting (three points in the upper right corner) -- inching setting. Turn on the inching state of channel 1 and channel 2, and set the watering time you need (channel 1 is pump a, channel 2 is pump B). After setting, please click the top right corner to save. Under the manual or automatic state, the water pump will run according to the inching time you set, and stop after reaching the set time. Click to enter the device interface Click options inching setting 1. Channel 1 corresponds to pump a; channel 2 corresponds to pump B. the starting time of the two pumps is set separately, and the user can set multiple groups of watering schemes. 2. After setting, whether the device is online or offline, the built-in chip will execute the setting procedure on time according to the setting. matters needing attention 1. Large capacity and small caliber containers (such as pure water bucket) should be selected as far as possible to meet the capacity demand and reduce water evaporation;

2. The position of the water container is relatively lower than the flowerpot to prevent the water in the bucket from directly flowing into the flowerpot without starting up in the sealed pipeline. 3. When it is difficult to plug in and out the pipeline, hot water can be used to soften it before 4. Correctly use the inlet pipe filter, and do not use the sewage with large particle impurities as the water source to prevent blocking the water pipe or pump. 5. Before setting the watering time, test the water flow and time manually. 6. The host has built-in circuit control board. Please do not place it in the open air. Rain, soaking and other harsh environment will cause fatal damage to the host. 7. When not in use for a long time, pull out the adapter, take out the battery, and properly place the host in a dry environment. 8. Under the condition of only using battery power supply, the endurance depends on the working frequency, working intensity, battery performance and other comprehensive conditions. When replacing batteries, 4 batteries need to be replaced at the same time. 9. The automatic watering device is only used for intermittent watering, and can not be used as a pump to continuously transport fluid medium for a long time, otherwise it will seriously reduce the service life of the main engine diaphragm pump. FCC WARNING This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-- Reorient or relocate the receiving antenna.

-- Increase the separation between the equipment and receiver.

-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-- Consult the dealer or an experienced radio/TV technician for help. To maintain compliance with FCCs RF Exposure guidelines, This equipment should be installed and operated with minimum 20cm distance between the radiator and your body: Use only the supplied antenna.

FesmTek Technology Limited Agent Authorization Company: FesmTek Technology Limited Ltd.Address: 2nd Floor, Building A3, Shamin Industrial Park, Wan'an Road, Ma'anshan Community, Shajing Street, Bao'an District, Shenzhen, China Product Name: Automatic drip Irrigation kit Model Number(s): FESMWFJH103 Product Description: Automatic drip Irrigation kit We authorize MiCOM Labs Inc., 575 Boulder Court, Pleasanton, California 94566, USA, to act on our behalf on all matters concerning the certification of above named equipment. We declare that MiCOM Labs Inc. is allowed to forward all information related to the approval and certification of equipment to the regulatory agencies as required and to discuss any issues concerning the approval application. Any and all acts carried out by MiCOM Labs on our behalf shall have the same effect as acts of our own. Jerry zhang Date: 2022-06-24 Manager 2nd Floor, Building A3, Shamin Industrial Park, Wan'an Road, Ma'anshan Community, Shajing Street, Bao'an District, Shenzhen, China Signature:

Name:

Title:

Company:

FesmTek Technology Limited Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 2022/06/24 Subject; Request for Confidentiality FCC ID: 2A7JJWFJH103 To Whom It May Concern, Pursuant to the provisions of the Commissions rules Title 47 Sections 0.457 and 0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. Schematic Diagram Block Diagram Operational Description In additional to above mentioned documents, in order to comply with the marketing regulations in Title 47 CFR 2.803 and the importation rules in Title 47 CFR 2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices, we request Short Term Confidentiality of the following attachment(s);

User Manual OR For 45 days, pursuant to Public Notice DA 04-1705. For 180 days pursuantto KDB 726920 D01. It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature:

Name: Jerry zhang Title: Manager