Filser Electronic GmbH GewerbestraBe 2 86875 Waal ATR 57 COM e MEM. VOL /SQ ON User manual IRE ElectroniGmbH Gewerbestrake 2 86875 Waal Contents USER INTERFACE DISPLAY INSTALLATION Panel installation 3.2 Installation of the antenna KK) Pin-layout 4 PUTTING INTO OPERATION 4.1 ON-switch 4.2 Volume regulation rR) Squelch level regulation 4.4 Memory selector 4.5 SOCCER ete Beet Ad 4.6 Low-battery 7 a Pim eect CaCl 5 TRANSMITTING 7 TECHNICAL REFERENCE mesma caennne OTe cya el=cci t8- | (Xo 86875 Waal 1 User interface B122T17-
aaah
. Volume / squelch push-button
. ON/ OFF switch
. MHz/ kHz push-button
. Tuningknob for volume, squelch and selected frequency
. Change selected frequency to active frequency Ams) (o)i-m ole lice) g
. Select stored frequency tL X=1m ElectroniGmbH GewerbestraRe 2 86875 Waal Re aeeye-lireliteya 3.1 Panel installation The ATR 57 is fixed in the panel with the four screws in instrument head. The cut-out diameter for placing the ATR 57 in the panel is standard 57mm. Tip: One should lookout for a place in the panel which provides easy installing, a good view and reachability for the pilot sitting in normal position. Avoid mounting near hot places. So you do not need any external cooling device like a fan or similar. One should pay attention having enough space behind the backside of the ATR 57 for connectors and cables. The cable harness should be as short as possible. Avoid cable run near strong noise sources like the ignition coil, light dynamo or battery charger. This can cause a low frequency noise on the speaker. Your service company provides all needed cables, the connectors are delivered with your ATR 57. ai scam =a (=Xeske) 0) (OMe 100]) a OTe - Ve el =s- 08-1 (C2 86875 Waal 3.2 Installation of the antenna The ATR 57 works with a normal 500Q-COM-antenna. Polarization must be vertical. A whip antenna (aerial) is not necessary. Using a broad band COM-antenna provides a higher efficiency over the frequency band. One should fix the antenna corresponding to manufacturers advises. Some important things are listed below:
e Unsymmetrical antennas. (e.g. 4/4-Antenna) should be mounted on plane metal surfaces or metal plates of at least 50 x 50cm. e The antenna should have the maximal possible distance to motor, propeller and so on. This avoids getting modulation on your signal. Again the COM-antenna should have the maximal possible distance to the NAV-antenna in order to avoid inter-
iicalalecton
@ aa vcyT ers Lid 14 ates mlecelereloteyiay og augydposy}
real ra oy ore]
ETe [evel ero) =) 3 V4 FA Uole elope ETON Jaxpeds Toob > tee aL Kol ElectronitGmbH Gewerbestrafe 2 86875 Waal 3.3 Pin-layout arise Electroni@mbH GewerbestraBe 2 86875 Waal 4 _ Putting into operation One will find all elements for operating the radio on the frontplate. 4.1__ON-switch The ,ON-OFF*-switch (2) is on the left side in the middle. The radio is active, when the switchposition is ,ON (upper side). 4.2 Volume regulation Push one time the Volume/Squelch push-button (1) (located on the upper left side) to get into the volume mode. By turning the tuning knob (4) one can change the volume. The device will leave the volume mode, when there is no change for some seconds. The selected level is active only until the ATR 57 is switched off. To use this level as switch on default, push the store button (6) while the device is in the volume mode. For confirmation the ATR 57 shows ,ST* in its display. 4.3__Squelch level requlation Push two times the Volume/Squelch push-button (1), to get into the squelch mode, then follow the instructions, listed in chapter 4.2.. mice Electroni GmbH GewerbestraBe 2 86875 Waal 4.4 Memory selector The memory selector (7) is located in the upper middle. It is used for selecting previous stored frequencies or for saving a frequency on one of the 9 possible places. Between place 9 and 1 (the white line on the memory selector shows downward) one will find the operation mode for selecting a frequency and changing it to active. 4.5 Selecting and storing a frequency Turn the memory selector in the position between memory place 1 (M1) and 9 (M9) (the white line on the memory selector shows downward). In the first line of the display one can read the actual active frequency, in the second line is displayed the changeable frequency. To change between the MHz- and kHz-range use button (3), this is the down left-handed button. A small arrow (9) shows the actual changed range. Now you can change the value of the selected range by using the tuning knob (4). With the down right-handed button (5) this new frequency can be activated. Now it is displayed in the first line, the old active frequency is disactivated and written in the second line. Turn the memory selector (7) onto the place, you want the new frequency to be saved, press the store button (6), ready. 4.6 Low-battery If the battery voltage comes below 10,5V a blinking ,B will be shown in upper left corner of the display. Now a regular operation of the device can not longer be warrented. Filser ElectroniGmbH GewerbestraBe 2 86875 Waal 4.7__Losing frequency If the actual used frequency has an untolerable difference to the displayed frequency a "-" (12) will appear in the upper right corner of the display. In this case the ATR 57 is working not properly and must be returned to the manufacturer. Notice:
Sometimes the "-" may be shown, but it disappears when the frequency is changed or the device is switched off and on. This effect is due to strong noise from outside the ATR 57. This is eM e mem ww ia wey A 5 Transmitting By using the transmitting key (PTT), the ATR 57 will change to the transmitting mode on the actual frequency shown in the upper line of the display. As long as the transmission takes place a "T" will be shown instead of the decimal point between the MHz- and kHz-value of the actual frequency (upper line), to control the proper function of the device. If the actual used frequency has an untolerable difference to the displayed frequency a "-" (12) will appear in the upper right corner of the display. In this case there will be no transmission. ati eictan oi (ave: (rele (eMeTanleyal GewerbestraBe 2 86875 Waal YM Xo ala lier: macy ices Frequency range: 118,000 .... 136,975 MHz Quantity of channels: 760
-Channel spacing: Pree V4 Modulation: _ AMDSB, 70% modulation Operation modus: alternate talking on one frequency HF-output power: > 1 Watt NF-output power: sel Voltage: 10,5 Vupto16V Current carrying: recieving 100 mA, transmitting 1A Dynan cae Ree en Weight: 500 g Certification: Reg TP 321 ZV 034