FCC ID: T2X-V3-CLESS contactless system of validation, payment or identification

Parc Lafayette 6 rue Isaac Newton 25075 Besanon France

+33 3 81 54 56 00 Contact@flowbird.group V3 CLESS User Manual V3 CLESS User Manual www.flowbird.group Parc Lafayette 6 rue Isaac Newton 25075 Besanon France

+33 3 81 54 56 00 Contact@flowbird.group FOREWORD INSTALLATION. We recommend you to read these instructions very carefully. They are included with your V3 CLESS Reader in order to explain its installation. USE. Once it is installed and equipped with the application you case use your V3 CLESS reader. GUARANTEE AND SAFETY. In order to benefit from the guarantee on this equipment and in order to follow the safety instructions, only authorized person shall entrust assembly or disassembly procedures and installed the reader. CONTENTS 1- SAFETY INSTRUCTIONS .................................................................................................................................... 3 2- UNPACKING. PRODUCT CONTENTS ................................................................................................................ 4 3- DESCRIPTION OF THE RF READER ................................................................................................................. 5 4- INSTALLING THE V3 CLESS ................................................................................................................................. 13 4.1 CLESS reader ................................................................................................................................................... 13 4.2 Antenna ............................................................................................................................................................. 14 INSTALLING AND REMOVING SECURITY ACCESS MODULES .................................................................... 15 5-

6- DAILY USE ......................................................................................................................................................... 16 7- V3 CLESS CHARACTERISTICS........................................................................................................................ 16 8- EC STANDARD COMPLIANCE MARKING ....................................................................................................... 17 9- FCC COMPLIANCE STATEMENT ..................................................................................................................... 17 V3 CLESS User Manual www.flowbird.group Parc Lafayette 6 rue Isaac Newton 25075 Besanon France

+33 3 81 54 56 00 Contact@flowbird.group 1- SAFETY INSTRUCTIONS A- In order to power down your V3 CLESS :

Disconnect the V3 CLESS power supply block from the electric power supply network B- Electrical power supply Only use Flowbird CLESS reader cable Only use Flowbird antenna cable with its Ferrite for EMI protection The V3 CLESS input voltage should be +12VDC +/- 10%

C- Reader cover Flap The cover flap located on the side ( see chapter installation and removal of Sams) must be in place during normal operation D- Warning Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. This device must be professionally installed V3 CLESS User Manual www.flowbird.group Parc Lafayette 6 rue Isaac Newton 25075 Besanon France

+33 3 81 54 56 00 Contact@flowbird.group 2- UNPACKING. PRODUCT CONTENTS Carefully preserve the packaging of the V3 CLESS and the antenna. It must be re-used whenever the reader is shipped. V3 CLESS User Manual www.flowbird.group Parc Lafayette 6 rue Isaac Newton 25075 Besanon France

+33 3 81 54 56 00 Contact@flowbird.group 3- DESCRIPTION OF THE RF READER Reminder of Safety Instructions :

Select the recommended electrical Power from Excelsys RF antenna connectors USB Power supply V3 CLESS User Manual www.flowbird.group Parc Lafayette 6 rue Isaac Newton 25075 Besanon France

+33 3 81 54 56 00 Contact@flowbird.group Diagram of connection Central Unit CLESS power supply cable CLESS USB cable CLESS reader Power supply converter IMS Antenna CAR_1000006460 or IML5 Antenna CAR_1000000081 Gate Antenna ELM_404304686 Paypass Antenna ELM_1000008317 Unstacker Antenna ELM_1000004108 V3 CLESS User Manual www.flowbird.group Parc Lafayette 6 rue Isaac Newton 25075 Besanon France

+33 3 81 54 56 00 Contact@flowbird.group Only 5 different antennas can be integrated ( ref ELM_404304686/ ELM_1000004108 /

CAR_10000000081 / CAR_1000006460 / ELM_1000008317) Gate antenna Top (ELM_404304686) Gate antenna Bot (ELM_404304686) V3 CLESS User Manual www.flowbird.group Parc Lafayette 6 rue Isaac Newton 25075 Besanon France

+33 3 81 54 56 00 Contact@flowbird.group IML5 antenna Top (CAR_1000000081) IML5 antenna Bot (CAR_1000000081) V3 CLESS User Manual www.flowbird.group Parc Lafayette 6 rue Isaac Newton 25075 Besanon France

+33 3 81 54 56 00 Contact@flowbird.group Unstacker antenna Top (ELM_1000004108) Unstacker antenna Bot (ELM_1000004108) V3 CLESS User Manual www.flowbird.group Parc Lafayette 6 rue Isaac Newton 25075 Besanon France

+33 3 81 54 56 00 Contact@flowbird.group IMS antenna Top (CAR_1000006460) IMS antenna Bot (CAR_1000006460) V3 CLESS User Manual www.flowbird.group Parc Lafayette 6 rue Isaac Newton 25075 Besanon France

+33 3 81 54 56 00 Contact@flowbird.group Paypass antenna Top (ELM_1000008317) Paypass antenna Bot (ELM_1000008317) V3 CLESS User Manual www.flowbird.group Parc Lafayette 6 rue Isaac Newton 25075 Besanon France

+33 3 81 54 56 00 Contact@flowbird.group Contactless reader cabling Power cable The CLESS reader is supplied with the connection card via a cable marked "PARAGON READER". Communications cable The connection between the CLESS reader and the PC is made with a USB/mini USB cable Antenna cable The connection between the reader module and the different antennas is made with a coaxial cable V3 CLESS User Manual www.flowbird.group Parc Lafayette 6 rue Isaac Newton 25075 Besanon France

+33 3 81 54 56 00 Contact@flowbird.group 4- INSTALLING THE V3 CLESS 4.1 CLESS reader Tools required: an 8 mm open-end spanner Time required for the intervention: 2 min Other components to remove/Preliminaries: switch off the power to the devices in EMS mode or with the button on the front of the CPU. Screw the two bolts holding the CLESS READER. Connect the cables on CLESS reader. Communication cable Power supply cable Antenna cable Fixing nut (x2) Press the power button device of the CPU. Perform a functional test using the "test connection map" from the menu EMS "travel card reader. V3 CLESS User Manual www.flowbird.group Parc Lafayette 6 rue Isaac Newton 25075 Besanon France

+33 3 81 54 56 00 Contact@flowbird.group 4.2 Antenna Tools required: none Clip the antenna into the bracket Connect the antenna cable. V3 CLESS User Manual www.flowbird.group Parc Lafayette 6 rue Isaac Newton 25075 Besanon France

+33 3 81 54 56 00 Contact@flowbird.group 5- INSTALLING AND REMOVING SECURITY ACCESS MODULES Tools required: an 5.5 mm open-end spanner Time required for the intervention: 2 min Unscrew the nut that secures the SAM access panel. Remove the cover. Insert the SIM cards. Replace the cover. Tighten the nut that locks the door. Trappe d'accs aux SAMs V3 CLESS User Manual www.flowbird.group Parc Lafayette 6 rue Isaac Newton 25075 Besanon France

+33 3 81 54 56 00 Contact@flowbird.group 6- DAILY USE No specific care shall be done. Clean the antenna each year with Isopropanol 7- V3 CLESS CHARACTERISTICS Physical Characteristics Mass : approximately 300g without cable Dimensions : approximately 109x93x32 mm (LxWxH) Standards See EC standard compliance marking in appendix Operating conditions Class II equipement Electric supply network : 12VDC +/- 10%

Max. consumption : 0.5 A Ambiant temperature : from -20C to +60C Max. relative humidity : 90% at +60C Communication : USB2.0 full speed interface Storage conditions Storage temperature : -40C, +70C Max relative humidity : 90% at +60C V3 CLESS User Manual www.flowbird.group Parc Lafayette 6 rue Isaac Newton 25075 Besanon France

+33 3 81 54 56 00 Contact@flowbird.group 8- EC STANDARD COMPLIANCE MARKING This product complies with the rules for CE marking. The applicable directives depend on the presence of the radio communication option:

The product complies with the following directives:

Directive 2014/53/EU of the European Parliament and of the Council of 16 April 2014 on the harmonisation of the law of the Member States relating to the making available on the market of radio equipment and repealing Directive 1999/5/EC Council Recommendation 1999/519/EC of 12 July 1999 on the limitation of exposure of the general public to electromagnetic fields (0 Hz to 300 GHz) 9- FCC COMPLIANCE STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Connect the equipment into an outlet on a circuit different from that to Increase the separation between the equipment and receiver. which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help This equipment with its antenna complies with FCCs radiation exposure limits set forth for an uncontrolled environment. To maintain compliance, follow the instructions below :

1. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 2. Avoid direct contact to the antenna, or keep contact to a minimum while using this equipment. V3 CLESS User Manual www.flowbird.group Parc Lafayette 6 rue Isaac Newton 25075 Besanon France

+33 3 81 54 56 00 Contact@flowbird.group FCC label placed on the CLESS reader V3 CLESS User Manual www.flowbird.group Parc Lafayette 6 rue Isaac Newton 25075 Besanon France

+33 3 81 54 56 00 Contact@flowbird.group POSITION OF THE FCC ID V3 CLESS User Manual www.flowbird.group

Parc Lafayette 6 rue Isaac Newton 25075 Besanon France

+33 3 81 54 56 00 Contact@flowbird.group V3 CLESS ID label/Location information FCC ID T2X-V3-CLESS Axio Touch - ID label/Location information www.flowbird.group Parc Lafayette 6 rue Isaac Newton 25075 Besanon France

+33 3 81 54 56 00 Contact@flowbird.group POSITION OF THE FCC ID Axio Touch - ID label/Location information www.flowbird.group Parc Lafayette 6 rue Isaac Newton 25075 Besanon France

+33 3 81 54 56 00 Contact@flowbird.group FCC label placed on the CLESS reader Axio Touch - ID label/Location information www.flowbird.group

Parc Lafayette 6 rue Isaac Newton 25075 Besanon France

+33 3 81 54 56 00 Contact@flowbird.group V3 CLESS FCC label sample FCC ID T2X-V3-CLESS V3 CLESS - FCC label sample www.flowbird.group Parc Lafayette 6 rue Isaac Newton 25075 Besanon France

+33 3 81 54 56 00 Contact@flowbird.group MODELE OF THE FCC ID LABEL V3 CLESS - FCC label sample www.flowbird.group

Parc Lafayette 6 rue Isaac Newton 25075 Besanon France

+33 3 81 54 56 00 Contact@flowbird.group Attn: TIMCO Engineering Inc. 849 N.W. State Road 45 P.O. Box 370 Newberry, Florida 32669 Authority to Act as Agent FCC ID: T2X-V3-CLESS On our behalf, I appoint M. Mathieu DUMESNIL from Emitech Angers, 21 rue de la Fuye PA de Lanserre, 49610 Juign sur Loire FRANCE, to act as our agent in the preparation of this application for equipment certification. I certify that submitted documents properly describe the device or system for which equipment certification is sought. I also certify that each unit manufactured, the Federal Communications Commissions regulations will have affixed to it a label identical to that submitted for approval with this application. imported or marketed, as defined in For instances where our authorized agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for certification, as specified by TIMCO Engineering Inc., still resides with FLOWBIRD. This authorization is valid until further written notice from FLOWBIRD. Date : February 19, 2023 By Eric EPENOY Qualification and conformity test technician Signature

Attn: TIMCO Engineering Inc. 849 N.W. State Road 45 P.O. Box 370 Newberry, Florida 32669 FCC ID: T2X- V3-CLESS Justification statement for antenna I confirm that all measurements were performed radiated (as might be the case for Part 15.249 devices) and therefore additional antenna gain documentation is not required. Date : 09 March 2023 By Mathieu Dumesnil Radio Technical Manager Sige Social : Emitech 3 avenue des Coudriers - Z.A. de lObservatoire - 78180 MONTIGNY LE BX - France Siret : 344 545 645 00022 - Tl. : 33 (0)1 30 57 55 55 - Fax : 33 (0)1 30 43 74 48 - E-mail : contact@emitech-group.com - URL : www.emitech.fr SAS au capital de 1 560 000 - R.C.S. VERSAILLES B 344 545 645 - APE 7112B

Parc Lafayette 6 rue Isaac Newton 25075 Besanon France

+33 3 81 54 56 00 Contact@flowbird.group Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: February 19, 2023 Ref: Attestation Statements Part 2.911(d)(7) Filing FCC ID: T2X-V3-CLESS FLOWBIRD (the applicant) certifies that, as of the date of the filing of the application, Benoit RELIQUET is our designated U.S. agent for service of process for the above referenced FCC ID. FLOWBIRD accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. Benoit RELIQUET accepts, as of the date of the filing of the application, the obligation of the designated U.S. agent for service of process for the above referenced FCC ID. Designated U.S. Agent Information:

Name: FLOWBIRD FRN: 0033617978 Address: Unit 7 - 40 Twosome Drive | Moorestown New Jersey | 08057 | USA Contact Person: Benoit RELIQUET President FLOWBIRD NAM Tel.: 856-813-6255 Email: benoit.reliquet@flowbird.group FLOWBIRD NAM Benoit RELIQUET Sincerely, FLOWBIRD Eric EPENOY Rev 1/26/2023

Parc Lafayette 6 rue Isaac Newton 25075 Besanon France

+33 3 81 54 56 00 Contact@flowbird.group Attn: TIMCO Engineering Inc. 849 N.W. State Road 45 P.O. Box 370 Newberry, Florida 32669 Confidentiality Request regarding application for certification of FCC ID: T2X- V3-CLESS Pursuant to Sections 0.457 and 0.459 of the Commissions Rules, we hereby request confidential treatment of information accompanying this application as outlined below:

Exhibit Type Block Diagram Schematics CPL Schematics MUX Schematics Gate_Antenna_ELM_404304686 Schematics IML5_Antenna_CAR_1000000081 Schematics IMS_Antenna_CAR_1000006460 Schematics PAYPASS_Antenna_ELM_1000008317 Schematics UNSTOCKER_Antenna_ELM_1000004108 Operational Description Parts List Gate_Antenna_ELM_404304686 Parts List IML5_Antenna_CAR_1000000081 Parts List IMS_Antenna_CAR_1000006460 Parts List PAYPASS_Antenna_ELM_1000008317 Parts List UNSTOCKER_Antenna_ELM_1000004108 File Name T2X-V3-CLESS_BlkDia.pdf RD-PL-10040-41.pdf RD-PL-18044-10.pdf SCE_404003724_A.pdf SCE_1000000081_C.pdf SCE_1000006460_D.pdf SCE_1000007972_C.pdf SCE_1000004102_A_Evolut1.pdf T2X-V3-CLESS _OpDes.pdf BOM_ELM_404304686.pdf BOM_CAR_1000000081.pdf BOM_CAR_1000006460.pdf BOM_ELM_1000008317.pdf BOM_ELM_1000004108.pdf The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, Date : February 19, 2023 By Eric EPENOY Qualification and conformity test technician Signature

Parc Lafayette 6 rue Isaac Newton 25075 Besanon France

+33 3 81 54 56 00 Contact@flowbird.group Date: February 19, 2023 Federal Communications Commission Authorization and Evaluation Division 1435 Oakland Mills Road Columbia, MD 21046 SUBJECT: FCC Application for FCC ID: T2X-V3-CLESS To Whom It May Concern:

We, the undersigned, hereby attest to the fact that we will apply the supplier Declaration of Conformity procedure to the Class B digital devices portion of this composite filing. Note:

We understand that devices subject to the SDoC procedure are required to be tested to show compliance with the FCC technical regulations by a recognized accredited testing laboratory. The testing laboratory must be accredited by a Commission approved accreditation body or designated under the terms of a government-to-government Mutual Recognition Agreement (MRA). A listing of those accredited testing laboratories that have been recognized by the Commission is published on the FCC Webpage: https://apps.fcc.gov/oetcf/eas/reports/TestFirmSearch.cfm Select the "accredited" option to search for FCC recognized accredited test firms. Test facilities located in countries, where the U.S. does not have an operational Telecom MRA are not recognized by the FCC to test for the SDoC procedure. Regards, Date : February 19, 2023 By Eric EPENOY Qualification and conformity test technician Signature