This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Compliance Statement Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-- Consult the dealer or an experienced technician for help. 900MHz STATIONARY AUDIO GUIDE TRANSMITTER Thanks for purchasing our Stationary Audio Guide Transmitter. It allows the user to transmit the audio wirelessly in a certain range, up to 32G memory capacity for audio files storage. Connect the audio source to the bal./unbal. Input on the back of the transmitter. Hook up the antenna to the rear antenna jack. You can monitor the audio via the headphone jack in front of the panel. Save the GPS stations to free your hands. 1. ON/OFF SWITCH 2. LOCK BUTTON 3. CHANNEL UP/CHANNEL DOWN 4. BACKWARD/FORWARD 5. PLAY/PAUSE 6. VOLUME CONTROL FOR MONITORING 7. HEADPHONE OUTPUT 8. AUDIO INPUT 9. LINE/MIC SWITCH 10. PHANTOM POWER SWITCH 11. RF LEVEL SWITCH OPERATIONS 1. POWER ON Switch to ON. It takes a few seconds for the transmitter to read the mp3 files. After reading the mp3 files, the display will show the current mp3 file number then you may start use the transmitter. In case the GPS is turned on, then it takes 3 to 5 minutes for the GPS to do the positioning (there is a digit 1 ahead of GPS). If there are stations stored and the transmitter is sitting in one of the station, the display will show the station number and play the file number that is saved under this station. 2. NORMAL SETUP (under lock status) Press the LANGUAGE button to scroll through the language list. Press the or button to adjust the mp3 volume (00-16). Press digits 0-9 to input the mp3 number (001-999). Press the >II (play/stop) button to play or stop a mp3 file. Press the>>I or I<<(forward or backward) button to forward or backward. 3. GPS Setup (under unlock status) Turn on the GPS function on the transmitter in unlock status. Connect the GPS antenna to the transmitter and make sure that the external GPS antenna receiver is in the open air (best on top of the boat or buildings). Press and hold the LOCK button and switch on the transmitter. Wait till the GPS positioning is done, which takes about 3 to 5 minutes. There will be a digit 1 icon shown on the display right in front of the icon GPS, otherwise it is not successful. To save or rewrite a station needs to receive the GPS signal, erasing the stations doesnt need it. Press digit 7 or 8 to edit station number (max. can save 50 stations, the station number needs to match the mp3 file number so we need to save the files that need to be saved in the stations in the number from 001 to 050. If there are more than 50 files in the mp3, for the files that are played manually, we can number it from 051.). Press digit 9 to save or rewrite the current station. There will be ok icon that flashes once on the display. With the movement of transmitter, the user can save and rewrite other stations (It will save the latest GPS data if it is rewritten). To delete stations, press digit 9 to rewrite the station and then press digit 6 to delete, and there will be ERASE OK icon that flashes once on the display after five seconds. If you want to delete all stations, press digit 3 to delete, and there will be ERASE OK icon that flashes once on the display after five seconds. Technical Specifications Frequency Range: 903MHz 927MHz Modulation: GFSK Audio sampling: 24bit/32KHz up to mp3 file type Frequency Response: 20Hz-16KHz SNR: >90dB THD at 1KHz: <1%
Channels: 25 Channel spacing: 1MHz Current Draw: 260mA Troubleshooting 1) When there is STATIC INTERFERENCE or NO SOUND, please go through the following procedures to eliminate the problems. a. Make sure that the transmitter and receiver are set on the same channel. b. Check whether two transmitters are set at the same channel. Avoid two transmitters to be on the same channel. c. Sound level on the line input source may be too high. 2) When a NOISY SOUND occurs, please go through the following procedures to eliminate the problems. a. Make sure that the transmitter and receiver are within the distance range. b. Make sure that the sound level on the transmitter and audio sources are set at a reasonable level. c. Try changing the transmitter to a different frequency to see if the sound quality improves. In case the problem persists, please consult your dealer or FLUENT AUDIO.