FCC ID: 2ABRJ-228S Satellite Communications Device

 

AFIRS 228 Series Installation Manual Record of Revisions Rev. Issue Date Description Pages By

--

22 April 2013 Initial issue. All S. Harke /

M. Preston Copyright 2013 by FLYHT Aerospace Solutions Ltd. This document is company confidential and contains information that is proprietary to FLYHT Aerospace Solutions Ltd. It may not, in whole or part, be copied, photocopied, translated, reduced or transferred to any electronic medium or machine-readable form without prior consent in writing from FLYHT Aerospace Solutions Ltd. The following names are trademarks of FLYHT Aerospace Solutions Ltd.: FLYHT, FLYHTStream, AFIRS and UpTime. AFIRS 228 Series Installation Manual Table of Contents 1. Introduction ............................................................................................................................. 1 1.1 Applicability ..................................................................................................................... 1 1.2 Model Designations ........................................................................................................ 1 1.2.1 AFIRS 228B ....................................................................................................... 1 1.2.2 AFIRS 228S ....................................................................................................... 1 1.3 Part Numbers .................................................................................................................. 1 1.4 Reference Documents .................................................................................................... 2 1.5 Definitions of Acronyms and Terms ................................................................................ 3 2. Description and Operation ...................................................................................................... 5 2.1 System Overview ............................................................................................................ 5 2.2 System Architecture ........................................................................................................ 6 2.3 External System Interfaces ............................................................................................. 6 3. Equipment Specifications ........................................................................................................ 9 3.1 Data Management Unit ................................................................................................... 9 3.1.1 General .............................................................................................................. 9 3.1.2 Mechanical Specifications .................................................................................. 9 3.1.3 Environmental Specifications AFIRS 228B ................................................... 10 3.1.4 Environmental Specifications AFIRS 228S ................................................... 10 3.2 Aircraft Configuration Module ....................................................................................... 11 3.2.1 General ............................................................................................................ 11 3.2.2 Mechanical Specifications ................................................................................ 11 3.2.3 Environmental Specifications ........................................................................... 11 3.3 AFIRS Antenna ............................................................................................................. 12 Interface Specifications ......................................................................................................... 13 4.1 DMU Rear Connector (J1) ............................................................................................ 13 4.1.1 Power Input Primary and Alternate ............................................................... 15 4.1.2 Chassis Ground ............................................................................................... 16 4.1.3 ARINC 573/717 Digital Serial Bus Input ........................................................... 16 4.1.4 ARINC 429 Digital Serial Bus Input .................................................................. 16 4.1.5 ARINC 429 Digital Serial Bus Output ............................................................... 16 4.1.6 RS-232/422 Digital Serial Bus .......................................................................... 16 4.1.7 Ethernet ............................................................................................................ 17 4.1.8 Discrete Inputs ................................................................................................. 17 4.1.9 Discrete Outputs .............................................................................................. 17 4. 250-0019 Rev. --

22 April 2013 Confidential and Proprietary to FLYHT Aerospace Solutions Ltd. Page iii AFIRS 228 Series Installation Manual 4.1.10 Two-Wire Phone .............................................................................................. 18 4.1.11 Microphone Input ............................................................................................. 19 4.1.12 Interphone Output ............................................................................................ 19 4.1.13 Iridium and GPS Antenna ................................................................................ 19 4.2 DMU Maintenance Connector (J2) ............................................................................... 19 4.3 Aircraft Configuration Module ....................................................................................... 20 4.4 ARINC 429 Receiver Protocols .................................................................................... 20 4.4.1 ACARS Communications Management Unit ................................................... 20 4.4.2 Airbus Centralized Fault Display System (CFDS) ............................................ 20 4.4.3 Flight Management System ARINC 702/A .................................................... 21 4.4.4 Flight Management System GAMA 429 ........................................................ 23 4.4.5 Flight Management System CMA-9000 ........................................................ 24 4.4.6 Basic DTP ........................................................................................................ 25 4.4.7 Pro Line 4/21 I/O Concentrator (GP Bus 5) .................................................. 25 4.4.8 Multi-Purpose Control Display Unit .................................................................. 26 4.4.9 Mode S Transponder ....................................................................................... 26 4.5 ARINC 429 Receiver Activity Status ............................................................................. 27 4.6 ARINC 429 Transmitter Protocols ................................................................................ 27 4.6.1 ACARS Output Bus .......................................................................................... 27 4.6.2 General Purpose Output Bus ........................................................................... 27 4.6.3 A739 MCDU Output Bus .................................................................................. 28 4.6.4 Airbus Centralized Fault Display System (CFDS) Output Bus ......................... 28 Installation Considerations .................................................................................................... 29 5.1 Data Management Unit (DMU) ..................................................................................... 29 5.2 Aircraft Configuration Module (ACM) ............................................................................ 30 5.3 AFIRS Antenna System ................................................................................................ 30 5.3.1 Antenna............................................................................................................ 30 5.3.2 Antenna Location ............................................................................................. 30 5.3.3 Antenna Mounting ............................................................................................ 30 5.3.4 Coaxial Cable................................................................................................... 31 INMARSAT Filter ............................................................................................. 32 5.3.5 Installation Materials ............................................................................................................. 33 6.1 Required Materials ........................................................................................................ 33 6.2 Additional Materials ...................................................................................................... 34 7. System Interface Wiring ........................................................................................................ 35 6. 5. Page iv Confidential and Proprietary to FLYHT Aerospace Solutions Ltd. 250-0019 Rev. --

22 April 2013 AFIRS 228 Series Installation Manual 7.1 General ......................................................................................................................... 35 7.2 Primary Power, Antenna, and ACM .............................................................................. 35 7.3 Alternate Power ............................................................................................................ 36 7.3.1 Redundant Power Supply ................................................................................ 36 7.3.2 Remote Start .................................................................................................... 36 7.4 Fault Indicator ............................................................................................................... 37 7.4.1 Fault Output (N/C) ............................................................................................ 37 7.4.2 Fault Output (N/O) ............................................................................................ 37 7.5 Flight Data Monitoring ................................................................................................... 38 7.6 ARINC 429 Interfaces ................................................................................................... 38 7.6.1 Receiver Protocols ........................................................................................... 38 7.6.2 Transmitter Protocols ....................................................................................... 39 7.7 MCDU ........................................................................................................................... 39 7.8 ICAO Address ............................................................................................................... 40 7.8.1 ACARS CMU .................................................................................................... 41 7.8.2 Mode S Transponder ....................................................................................... 42 7.9 Date, Time and Position ................................................................................................ 42 7.10Generic ARINC 429 Interfaces ..................................................................................... 43 7.11RS-232/422 Databus .................................................................................................... 43 7.12Ethernet ........................................................................................................................ 44 7.13Discrete Inputs .............................................................................................................. 46 7.13.1 Weight-On-Wheels Input .................................................................................. 46 7.13.2 Signal Level Configuration ............................................................................... 46 7.13.3 Logic Configuration .......................................................................................... 46 7.13.4 Function Assignment ........................................................................................ 47 7.14Discrete Outputs ........................................................................................................... 49 7.14.1 Logic Configuration .......................................................................................... 50 7.14.2 Function Assignment ........................................................................................ 50 7.15Satcom .......................................................................................................................... 51 7.15.1 Audio Integrating System ................................................................................. 51 7.15.2 DTMF Dialing Source ....................................................................................... 54 7.15.3 Satcom Handsets ............................................................................................. 55 8. System Configuration ............................................................................................................ 57 8.1 Connecting to the Maintenance Port ............................................................................. 58 8.1.1 Home Page Tab Descriptions .......................................................................... 59 8.1.2 Faults Page ...................................................................................................... 60 250-0019 Rev. --

22 April 2013 Confidential and Proprietary to FLYHT Aerospace Solutions Ltd. Page v AFIRS 228 Series Installation Manual 8.1.3 Part Numbers Page ......................................................................................... 60 8.2 Accessing Maintenance Mode ...................................................................................... 60 8.2.1 Maintenance Mode Menu Descriptions ............................................................ 61 8.3 Configuring the AFIRS 228 System .............................................................................. 62 8.3.1 Configuring the Address Book ......................................................................... 62 8.3.2 Configuring the Owner Requirements Table .................................................... 63 8.3.3 Configuring the Installation Configuration Table .............................................. 68 8.3.4 Calibrating SLIC ............................................................................................... 69 8.4 Upgrading AFIRS 228 Software ................................................................................... 69 8.4.1 Upgrade Materials ............................................................................................ 69 8.4.2 Upgrade Procedure .......................................................................................... 69 8.5 Exiting Maintenance Mode ........................................................................................... 73 9. Maintenance and Checkout .................................................................................................. 75 9.1 Post-Installation Checkout ............................................................................................ 75 9.1.1 Before Power-On Tests ................................................................................... 75 9.1.2 Power-On Tests ............................................................................................... 75 9.1.3 Aircraft Systems Interface Tests ...................................................................... 76 9.1.4 Operational System Tests ................................................................................ 77 9.1.5 EMI Tests ......................................................................................................... 79 Instructions for Continued Airworthiness ...................................................................... 79 9.2 List of Figures Figure 2-1 AFIRS Operational Concept ..................................................................................... 5 Figure 2-2 AFIRS System Block Diagram .................................................................................. 6 Figure 2-3 AFIRS External Interfaces ........................................................................................ 7 Figure 3-1 DMU Outline Drawing ............................................................................................... 9 Figure 3-2 ACM Outline Drawing ............................................................................................. 11 Figure 4-1 DMU Connector Map .............................................................................................. 15 Figure 5-1 2MCU Mounting Tray ............................................................................................. 29 Figure 7-1 Primary Power, Antenna and ACM Interface .......................................................... 35 Figure 7-2 Alternate Power Interface ....................................................................................... 36 Figure 7-3 Fault (N/C) Interface ............................................................................................... 37 Figure 7-4 Fault (N/O) Interface ............................................................................................... 37 Figure 7-5 ARINC 717 Interface .............................................................................................. 38 Figure 7-6 MCDU Interface ...................................................................................................... 40 Page vi Confidential and Proprietary to FLYHT Aerospace Solutions Ltd. 250-0019 Rev. --

22 April 2013 AFIRS 228 Series Installation Manual Figure 7-7 ACARS Interface .................................................................................................... 41 Figure 7-8 Mode S Transponder Interface ............................................................................... 42 Figure 7-9 Serial Port Interface ................................................................................................ 44 Figure 7-10 Ethernet Interface ................................................................................................. 45 Figure 7-11 Discrete Input and Output Interfaces .................................................................... 49 Figure 7-12 Switched PTT Audio Interface .............................................................................. 53 Figure 7-13 Latched ACP Audio Interface ............................................................................... 54 Figure 7-14 Dial Pad Interface ................................................................................................. 55 Figure 7-15 Handset Interface ................................................................................................. 56 Figure 8-1 Maintenance Port Location ..................................................................................... 57 Figure 8-2 Home Page General Tab ..................................................................................... 58 Figure 8-3 Entering Maintenance Mode Message ................................................................... 60 Figure 8-4 Maintenance Mode Initial Display Screen ............................................................... 61 Figure 8-5 Address Book Screen ............................................................................................. 63 Figure 8-6 ORT Screen ............................................................................................................ 64 Figure 8-7 Installation Configuration Table Screen .................................................................. 68 Figure 8-8 SLIC Calibration Screen ......................................................................................... 69 Figure 8-9 Upgrade Progress ................................................................................................... 70 Figure 8-10 Software Loading Progress Screens .................................................................... 71 Figure 8-11 Exit Message ........................................................................................................ 71 Figure 8-12 Exit Maintenance Mode Progress Bar .................................................................. 72 Figure 8-13 Exiting Prompt Message ....................................................................................... 73 Figure 8-14 Save Prompt ......................................................................................................... 73 Figure 8-15 Exit and Restart Progress Screen ........................................................................ 74 Figure 8-16 Software Part Number Status Screen ................................................................... 74 List of Tables Table 1-1 Part Numbers ............................................................................................................. 1 Table 1-2 References ................................................................................................................. 2 Table 1-3 Acronyms and Terms ................................................................................................. 3 Table 4-1 J1A Top Plug (TP) Insert ......................................................................................... 13 Table 4-2 J1B Middle Plug (MP) Insert .................................................................................... 14 Table 4-3 J1C Bottom Plug (BP) Insert .................................................................................... 15 Table 4-4 ACM Connections .................................................................................................... 20 Table 4-5 ARINC 429 Receiver Port Monitoring ...................................................................... 27 Table 5-1 Coaxial Cable Types ................................................................................................ 31 Table 6-1 Installation Materials ................................................................................................ 33 Table 7-1 Serial Port Pin Assignments .................................................................................... 43 Table 7-2 Discrete Input Configurable States .......................................................................... 47 250-0019 Rev. --

22 April 2013 Confidential and Proprietary to FLYHT Aerospace Solutions Ltd. Page vii AFIRS 228 Series Installation Manual Appendices Appendix A ICT Worksheet...................................................................................................... 81 Appendix B ORT Worksheet .................................................................................................... 87 Appendix C Environmental Qualification Forms ...................................................................... 91 Page viii Confidential and Proprietary to FLYHT Aerospace Solutions Ltd. 250-0019 Rev. --

22 April 2013 AFIRS 228 Series Installation Manual INTRODUCTION 1. This section provides a general introduction to the AFIRS 228 Series system and its applicable standards and references. 1.1 Applicability This Installation Manual provides the information necessary to plan the AFIRS 228 system installation and integration in the aircraft. It defines the mechanical and electrical interfaces for each Line Replaceable Unit (LRU) and provides the procedures required to properly configure, test, and maintain the AFIRS 228 system. This manual is applicable to the following software version(s):

SCN: 2.0.0 and later 1.2 Model Designations There are two model designations for the AFIRS 228 Series system. 1.2.1 AFIRS 228B The AFIRS 228B is the Baseline model version of the AFIRS 228 Series. It has a single Iridium link shared between voice and data non-safety services. 1.2.2 AFIRS 228S The AFIRS 228S will be certified to TSO C-159a for voice and data safety-services. It has a dual-channel Iridium link, one dedicated for safety-services data and the other prioritized for safety-services voice. Only the AFIRS 228B is available at this time. However, this manual does provide additional planning information for the future AFIRS 228S system. Throughout this document, any reference to the AFIRS 228B applies only to the non-TSOd AFIRS 228B model, while references to AFIRS 228S apply only to the TSOd AFIRS 228S model. References to AFIRS 228 or AFIRS 228 Series apply to both model variants. 1.3 Part Numbers The following part numbers are defined for the LRUs of the AFIRS 228 Series systems. Table 1-1 Part Numbers Description AFIRS 228S Data Management Unit (DMU) AFIRS 228B Data Management Unit (DMU) AFIRS 228 Aircraft Configuration Module (ACM) Part Number 502-1001-x 502-2001-x 502-3001-x 250-0019 Rev. --

22 April 2013 Confidential and Proprietary to FLYHT Aerospace Solutions Ltd. Page 1 AFIRS 228 Series Installation Manual 1.4 Reference Documents Table 1-2 References Ref. Document Number Description 1. ANSI/TIA/EIA-232-

F-1997 2. ARINC 429-19 3. ARINC 573-7 4. ARINC 600-16 5. ARINC 619-3 6. ARINC 664-2 7. ARINC 702-6 8. ARINC 702A-3 9. ARINC 717-14 10. ARINC 718-4 11. ARINC 718A-2 12. ARINC 739A-1 13. ARINC 741-13 14. ARINC 758-2 15. ARINC 761-4 16. FAA TSO C-159a 17. GAMA Publication No. 11, Ver. 5.1 IEEE 802.3-2008 18. 19. RTCA/DO-160F Interface Between Data Terminal Equipment and Data Circuit-

Terminating Equipment Employing Serial Binary Data Interchange Mark 33 Digital Information Transfer System (DITS) Mark 2 Aircraft Integrated Data System (AIDS Mark 2) Air Transport Avionics Equipment Interfaces ACARS Protocols For Avionic End Systems Aircraft Data Networks Flight Management Computer System Advanced Flight Management Computer System Flight Data Acquisition and Recording System Mark 3 Air Traffic Control Transponder (ATCRBS/MODE S) Mark 4 Air Traffic Control Transponder (ATCRBS/MODE S) Multi-Purpose Control And Display Unit Aviation Satellite Communication System Communications Management Unit (CMU) Mark 2 Second Generation Aviation Satellite Communication System, Aircraft Installation Provisions Technical Standard Order, Avionics Supporting Next Generation Satellite Systems (NGSS) ARINC 429, General Aviation Subset IEEE Standard for Information Technology-Specific Requirements

- Part 3: Carrier Sense Multiple Access with Collision Detection

(CMSA/CD) Access Method and Physical Layer Specifications Environmental Conditions and Test Procedures for Airborne Equipment Page 2 Confidential and Proprietary to FLYHT Aerospace Solutions Ltd. 250-0019 Rev. --

22 April 2013 AFIRS 228 Series Installation Manual Ref. Document Number Description 20. RTCA/DO-214 21. RTCA/DO-262A 22. TIA/EIA-422-B Audio Systems Characteristics and Minimum Operational Performance Standards for Aircraft Audio Systems and Equipment Minimum Operational Performance Standards for Avionics Supporting Next Generation Satellite Systems (NGSS) Electrical Characteristics of Balanced Voltage Digital Interface Circuits 1.5 Definitions of Acronyms and Terms Table 1-3 Acronyms and Terms Acronym ACARS ACM ACP AFIRS ANSI APU ARINC BPRZ CFDS CMC CMU DCU DITS DMU EFB EIA EWIS FAA Definition Aircraft Communications Addressing and Reporting System Aircraft Configuration Module Audio Control Panel Automated Flight Information Reporting System American National Standards Institute Auxiliary Power Unit Aeronautical Radio Incorporated Bipolar Return To Zero Centralized Fault Display System (Airbus) Central Maintenance Computer Communications Management Unit Data Concentrator Unit Digital Information Transfer System Data Management Unit Electronic Flight Bag Electronics Industry Association Electrical Wire Interconnection System Federal Aviation Administration 250-0019 Rev. --

22 April 2013 Confidential and Proprietary to FLYHT Aerospace Solutions Ltd. Page 3 AFIRS 228 Series Installation Manual Definition Flight Data Monitoring Flight Data Acquisition Unit Flight Management Computer Flight Management System General Aviation Manufacturers Association Global Positioning System Ground Service Equipment Harvard Bi-Phase Interface Control Document Iridium Certified Equipment Institute of Electrical and Electronics Engineers Line Replaceable Unit Multi-Purpose Control Display Unit Minimum Operational Performance Specifications Next Generation Satellite Systems Owner Requirements Table Public Branch Exchange Personal Computer Public Switched Telephone Network Push To Talk Radio Technical Commission for Aeronautics Satellite Communications Subscriber Identity Module Telecommunications Industry Association Technical Standard Order Weight on Wheels Word Per Second Confidential and Proprietary to FLYHT Aerospace Solutions Ltd. 250-0019 Rev. --

22 April 2013 Acronym FDM FDAU FMC FMS GAMA GPS GSE HBP ICD ICE IEEE LRU MCDU MOPS NGSS ORT PBX PC PSTN PTT RTCA Satcom SIM TIA TSO WOW WPS Page 4 AFIRS 228 Series Installation Manual 2. DESCRIPTION AND OPERATION This section describes the system operation and architecture. 2.1 System Overview The AFIRS 228 Series Automated Flight Information Reporting System provides multiple voice and data communications functions in the aircraft. The AFIRS provides a satellite voice communications (Satcom) link with the Public Switched Telephone Network (PSTN) via the Iridium satellite network. The system uses a standard ARINC 741/761 Satcom interface to the flight crews Audio Integrating System and ARINC 739A Multi-Purpose Control Display Units

(MCDUs) in the cockpit, as well as providing 3-extension PBX capability for up to 2 handsets in the cabin. For cockpits not capable of supporting the ARINC 741/761 interface, a dedicated AFIRS Dialer Pad can be installed in the cockpit. Figure 2-1 AFIRS Operational Concept Data capabilities include the monitoring, recording, and reporting of aircraft flight and system data which consists of aircraft movement and position reports, Flight Data Monitoring (FDM) data collection, system (e.g. engine) health and trend reports, and monitored parameter exceedance and exception reports. The AFIRS also provides an interface for Electronic Flight Bags (EFBs), which can provide real-time data connectivity to the Uptime server for various third-party EFB applications. This includes the ability to send and receive text messages. The AFIRS 228S adds a dedicated safety-services data channel that provides the capability to send and receive standard ACARS messages between the aircrafts Communications Management Unit (CMU) and a safety-services certified terrestrial service provider. 250-0019 Rev. --

22 April 2013 Confidential and Proprietary to FLYHT Aerospace Solutions Ltd. Page 5 AFIRS 228 Series Installation Manual 2.2 System Architecture The AFIRS 228 Series systems consist of modular avionics components that can be tailored to meet customer needs. The core system components are the Data Management Unit (DMU), the Aircraft Configuration Module (ACM), and the Iridium/GPS Antenna (see Figure 2-2). Optional components include the following:

Cockpit Dialer Pad Cabin Handset(s) (Wired or Cordless) Figure 2-2 AFIRS System Block Diagram 2.3 External System Interfaces The AFIRS system has a number of external interfaces which are listed below and described in detail in this section. Audio System Interface (1) ARINC 573/717 Receiver (1) ARINC 429 Transmitters (6) and Receivers (16) RS-232/422 Serial Ports (4) Ethernet Ports (4) Discrete Outputs (11) and Inputs (17) User Media Interfaces SIM (1), CF (1) Maintenance Interfaces Ethernet (1), ATE Serial (1) Figure 2-3 illustrates the interfaces that the AFIRS system provides to external aircraft systems or to the user. Iridium/GPS Antenna (1) Page 6 Confidential and Proprietary to FLYHT Aerospace Solutions Ltd. 250-0019 Rev. --

22 April 2013 AFIRS 228 Series Installation Manual Figure 2-3 AFIRS External Interfaces 250-0019 Rev. --

22 April 2013 Confidential and Proprietary to FLYHT Aerospace Solutions Ltd. Page 7 AFIRS 228 Series Installation Manual Audio System Interface (1) This interface consists of a Microphone Input to the DMU and an Interphone Output from DMU to connect to a standard (DO-214) Audio Integrating System (e.g. Audio Panel) in the aircraft. Software selectable discrete inputs and outputs can be configured to support this interface (e.g. Mic On, Chime, Chime Reset, End Call functions). ARINC 573/717 Receiver (1) This interface can be used to collect data from the Flight Data Acquisition Unit (FDAU), Data Concentrator Unit (DCU), or equivalent system in the aircraft. ARINC 429 Transmitters (6) and Receivers (16) These interfaces can be software-configured to connect to various aircraft systems to support both the display and control functions of the AFIRS system, as well as the data collection activities. Typical interfaced systems include MCDUs, Flight Management Systems (FMSs), ACARS CMUs, Mode S Transponders, Central Maintenance Computers

(CMCs), etc. RS-232/422 Serial Ports (4) These interfaces can be software-configured to connect to different aircraft systems. Typical interfaced systems include EFBs, Global Positioning Systems (GPSs), etc. Ethernet Ports (4) These interfaces can be used to connect to several different systems. Typical interfaced systems include EFBs, CMCs, etc. One of these ports can also be used to provide a remote maintenance port interface (e.g. in the flight compartment). Discrete Outputs (11) and Inputs (17) Discrete inputs and outputs can be used to provide or supplement various flight crew control and display interactions, particularly for voice functions. Discrete inputs can also be used to determine the states of various aircraft systems when this information is not available on a databus (e.g. Weight-on-Wheel, Doors Closed, etc.). Iridium/GPS Antenna (1) An antenna mounted on the top of the fuselage is used to communicate with both the Iridium satellite network and the GPS satellite network. User Media Interfaces SIM (1), CF (1) There are two types of media available for the user to insert or remove from the AFIRS system. The ACM contains a user accessible Subscriber Identity Module (SIM) card slot for storage of the Iridium communications management information. The DMU contains a front panel accessible Compact Flash card which is used to store Quick Access Recorder (QAR) data. Maintenance Interfaces Ethernet (1), ATE Serial (1) An RJ45 jack on the front panel provides Maintenance Port access using an Ethernet connection. Additional low-level access is also available to factory repair personnel via the ATE Serial Debug port. Page 8 Confidential and Proprietary to FLYHT Aerospace Solutions Ltd. 250-0019 Rev. --

22 April 2013 AFIRS 228 Series Installation Manual 3. EQUIPMENT SPECIFICATIONS This section describes the mechanical and environmental specifications of the components of the AFIRS 228 Series system. 3.1 Data Management Unit This section describes the mechanical and environmental specifications of the components of the Data Management Unit (DMU). 3.1.1 General The DMU is housed in an ARINC 600 2MCU enclosure, which is designed to be mounted in a standard ARINC 600 mounting tray. See Figure 3-1 for an outline of this component. Figure 3-1 DMU Outline Drawing 3.1.2 Mechanical Specifications Dimensions:

Weight:

Material/Finish:

Mounting:

7.81 x 2.27 x 15.02 (See Figure 3-1) 7.7 lbs. (3.49 kg.) Max. Aluminum Alloy with Blue Polyurethane Finish ARINC 600 2MCU Mounting Tray 250-0019 Rev. --

22 April 2013 Confidential and Proprietary to FLYHT Aerospace Solutions Ltd. Page 9 AFIRS 228 Series Installation Manual Rear Mating Connector: Size 2 ARINC 600 Receptacle Radiall P/N: NSXN2P201S0004 ITT P/N: BKAD2-313-300-04 Maintenance Connector: RJ45 (8P8C) Modular Connector Jack Flash Card:

CompactFlash (Type I or Type II) 3.1.3 Environmental Specifications AFIRS 228B Temperature (Operating): -55C to +70C (Without Iridium Satellite Communication) Temperature (Survival):

Altitude:

Vibration:

Humidity:

DO-160F Categories:

-40C to +70C (With Iridium Satellite Communication)

-55C to +85C 55,000 ft. DO-106F Cat. SCL and U2

<95% Non-Condensing (DO-106F Cat. A)

[(A2)(F2)X]BAD[(SCL)(U2)]XXXXXXZZ(XI)AZ[ZW][ST]MXXXAC Note:

Satellite voice and data communications functions in the AFIRS 228B are not operational below

-40C. At elevated temperatures (>60C), the voice modem has a maximum duty cycle of 60%. 3.1.4 Environmental Specifications AFIRS 228S Temperature (Operating): -55C to +70C

-55C to +85C Temperature (Survival):

Altitude:

55,000 ft. DO-160G Cat. SCL and U2 Vibration:

<95% Non-Condensing (DO-160G Cat. A) Humidity:

DO-160G Categories:

[(A2)(F2)X]BAD[(SCL)(U2)]XXXXXXZZ(XI)AZ[ZW][TT]MXXXAC Note:

DO-160G Categories for the AFIRS 228S are as specified by the design. Qualification tests on the AFIRS 228S DMU have not been completed to date. Page 10 Confidential and Proprietary to FLYHT Aerospace Solutions Ltd. 250-0019 Rev. --

22 April 2013 AFIRS 228 Series Installation Manual 3.2 Aircraft Configuration Module This section describes the mechanical and environmental specifications of the components of the Aircraft Configuration Module (ACM). 3.2.1 General The ACM is housed in small enclosure, which is designed to be mounted within 24 of the DMU rear connector. Typically, the ACM will be mounted on or near the ARINC 600 mounting tray used for the DMU. See Figure 3-2 for an outline of this component. Figure 3-2 ACM Outline Drawing 3.2.2 Mechanical Specifications Dimensions:

Weight:

Material/Finish:

1.75 x 1.75 x 0.63 0.2 lbs. (0.09 kg.) Max. Aluminum Alloy 3.2.3 Environmental Specifications Temperature (Operating): -55C to +70C Temperature (Survival):

-55C to +85C 55,000 ft. Altitude:

DO-160F Cat. SCL and U2 Vibration:

Humidity:

<95% Non-Condensing (DO-160F Cat. A)

[(A2)(F2)X]BAD[(SCL)(U2)]XXXXXXZZ(XI)AZ[ZW][ST]MXXXAC DO-160F Categories:

250-0019 Rev. --

22 April 2013 Confidential and Proprietary to FLYHT Aerospace Solutions Ltd. Page 11 AFIRS 228 Series Installation Manual 3.3 AFIRS Antenna The AFIRS Antenna is to be selected by the system integrator to be suitable for the installed aircraft environment. FLYHT has evaluated the following antennas and found them to function properly with the AFIRS 228 system, and generally they will meet most aircraft operating environments:

Sensor Systems P/N S67-1575-109 Sensor Systems P/N S67-1575-409 Sensor Systems P/N S67-1575-165 Sensor Systems P/N S65-8282-101 Aero Antenna AT2775-110GA Aero Antenna AT2775-110 When selecting an alternate antenna for use with the AFIRS 228 system, the antenna must meet the following criteria:

Be suitable for the installed aircraft environmental conditions. Note that in addition to the temperature, altitude, fluids susceptibility, considerations etc., the antenna must be approved for the expected aircraft lightning environment. Be approved by Iridium Communications Inc. as Iridium Certified Equipment (ICE). Meet the following antenna performance specifications:

Type:

Frequency Iridium:

Frequency GPS:

Coverage Volume:

VSWR (Max.):

Polarization:

Impedance (Nom.):

Power Handling (Min.):

Gain (Min.):

Passive Patch or Helical 1616 1626.5 MHz 1575 10 MHz 8.2 90 Elevation; 360 Azimuth 1.8:1 RHCP 50 Ohms 20W CW

+3 dBic @ Zenith

+0 dBic Weighted Average per DO-262A If the operator plans to upgrade to the AFIRS 228S in the future, the selected antenna should be qualified to TSO C-159a so that the system can then be approved for safety services use. Note:

Proper antenna selection and installation are critical to proper system operation. See 5.3 for antenna installation criteria and recommendations. Page 12 Confidential and Proprietary to FLYHT Aerospace Solutions Ltd. 250-0019 Rev. --

22 April 2013 AFIRS 228 Series Installation Manual INTERFACE SPECIFICATIONS 4. This section describes the interface specifications of the AFIRS 228 Series system components. 4.1 DMU Rear Connector (J1) Table 4-1 J1A Top Plug (TP) Insert 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 A B Ethernet 1A Tx+

Ethernet 1A Rx+

Ethernet 1A Rx-

Ethernet 1A Tx-

O O O O Ethernet 4B Tx+

Ethernet 4B Rx+

Ethernet 4B Rx-

Ethernet 4B Tx-

O O O O O O O O O O O O O O O O O O C O O O O O O O O O O O O O O D O O O O O O O O O O O O O O O E F Ethernet 2B Tx+

Ethernet 2B Rx+

Ethernet 2B Rx-

Ethernet 2B Tx-

O O O O O O O O O O O O O O O O O O O O O O O O O O G O O O O O O O O O O O O O O O H O O O O O O O O O O O O O O O J Ethernet 3B Tx+

Ethernet 3B Rx-

K Ethernet 3B Rx+

Ethernet 3B Tx-

O O O O O O O O O O O O O O O O O O O O O O O O O O 250-0019 Rev. --

22 April 2013 Confidential and Proprietary to FLYHT Aerospace Solutions Ltd. Page 13 AFIRS 228 Series Installation Manual 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Table 4-2 J1B Middle Plug (MP) Insert A O B O C O D O Ext. 1 Ext. 1 Ext. 1 Mic Audio Mic Audio Audio Out Hi Lo Ext. 1 Audio Out Lo No. 2 A429Rx B Hi No. 2 A429Rx A E O O F O O G No. 1 A429Rx A H No. 1 A429Rx B J No. 1 A429Tx A K No. 1 A429Tx B O O O O O O No. 1 Discrete Output No. 5 A429Rx A No. 10 A429Rx A No. 8 Discrete Input No. 2 RS232 Com No. 2 RS422Rx+

RS232RXD No. 11 Discrete Input No. 14 A429Rx A O O WOW 1 Discrete Input No. 5 A429Rx B No. 10 A429Rx B No. 2 Discrete Output No. 3 RS232 Com No. 2 RS422Rx-

RS232CTS No. 12 Discrete Input No. 14 A429Rx B No. 3 A429Rx A No. 3 A429Rx B No. 4 A429Rx A No. 4 A429Rx B O O O O O O No. 2 Discrete Input No. 6 A429Rx A No. 3 Discrete Input No. 6 A429Rx B No. 4 Discrete Input No. 7 A429Rx A No. 3 A429Tx A No. 12 A429Rx A No. 5 A429Tx A No. 3 A429Tx B No. 12 A429Rx B No. 5 A429Tx B No. 4 A429Tx A No. 3 Discrete Output No. 1 RS422Tx-

RS232TXD No. 5 Discrete Input No. 7 A429Rx B No. 4 A429Tx B No. 9 Discrete Input No. 1 RS422Tx+

RS232RTS No. 6 Discrete Input No. 8 A429Rx A No. 11 A429Rx A No. 4 Discrete Output No. 1 RS422Rx+

RS232RXD No. 7 Discrete Input No. 8 A429Rx B No. 11 A429Rx B No. 10 Discrete Input No. 1 RS422Rx-

RS232CTS No. 3 RS422Tx-

RS232TXD No. 3 RS422Tx+

RS232RTS No. 3 RS422Rx+

RS232RXD No. 3 RS422Rx-

RS232CTS No. 4 RS422Tx-

RS232TXD No. 4 RS422Tx+

RS232RTS No. 13 Discrete Input No. 6 A429Tx A No. 14 Discrete Input No. 6 A429Tx B No. 5 Discrete Output No. 15 A429Rx A No. 6 Discrete Output No. 15 A429Rx B No. 2 A429Tx A ACM Power ACM Data No. 9 A429Rx A No. 1 RS232 Com No. 13 A429Rx A No. 2 A429Tx B ACM Ground ACM Clock No. 9 A429Rx B No. 4 RS232 Com No. 13 A429Rx B No. 2 RS422Tx-

RS232TXD No. 2 RS422Tx+

RS232RTS No. 4 RS422Rx+

RS232RXD No. 4 RS422Rx-

RS232CTS No. 7 Discrete Output No. 16 A429Rx A No. 8 Discrete Output No. 16 A429Rx B No. 15 Discrete Input WOW HPP A717Rx A717Rx A O O O B O O O Fault Output N/C O O Fault Output N/O Chime Output O O O O O O O O O O O O O O O Phone Ext. 2 Tip Phone Ext. 2 Ring Phone Ext. 3 Tip Phone Ext. 3 Ring Page 14 Confidential and Proprietary to FLYHT Aerospace Solutions Ltd. 250-0019 Rev. --

22 April 2013 AFIRS 228 Series Installation Manual Table 4-3 J1C Bottom Plug (BP) Insert Description Pin Size 1 2 3 4 5 6 7 8 9 10 11 12 13 20 Not Used 12 Primary 28 VDC Power Input 12 Power Ground 20 Not Used 20 Remote Start Input 20 Not Used 12 Not Used 12 Chassis Ground 16 Alternate 28 VDC Power Input 16 Not Used 16 Not Used 5 Not Used 5 Iridium/GPS Antenna Figure 4-1 DMU Connector Map 4.1.1 Power Input Primary and Alternate 27.5 VDC 18.0 to 32.2 VDC Nominal Input:

Voltage Range:

Input Current Standby/Data (Typical): 228B: 585 mA (16.1 W) 228S: 640 mA (17.6 W) 228B: 725 mA (19.9 W) 228S: 725 mA (19.9 W) Input Current Max. Cont. (at 32.2 V): 228B: 1.40 A (45.1 W) 228S: 1.20 A (38.6 W) Input Current Voice Call (Typical):

Recommended Power Control Device: 3 to 5 Amp delayed action circuit breaker Note:

This is not a floating input. 28 VDC must be applied to the 28 VDC Power input and airframe ground to Power Ground input. 250-0019 Rev. --

22 April 2013 Confidential and Proprietary to FLYHT Aerospace Solutions Ltd. Page 15 AFIRS 228 Series Installation Manual 4.1.2 Chassis Ground For redundant chassis ground connection only. Not to be used as a normal current carrying conductor. Quantity:

Format:

1 DC Chassis Ground 4.1.3 ARINC 573/717 Digital Serial Bus Input Quantity:

Format:

Data Rate:

1 ARINC 573/717, HBP and BPRZ 64/128/256/512/1024 WPS 4.1.4 ARINC 429 Digital Serial Bus Input 16 DITS, ARINC 429 Low or high speed 12.5 Kbps 1%

100 Kbps 1%

Software Selectable Protocols Quantity:

Format:

Low Speed Data Rate:

High Speed Data Rate:

SSM/SDI/Data Definition:

4.1.5 ARINC 429 Digital Serial Bus Output Quantity:

Format:

Low Speed Data Rate:

High Speed Data Rate:

SSM/SDI/Data Definition:

6 DITS, ARINC 429 Low or high speed 12.5 Kbps 1%

100 Kbps 1%

Software Selectable Protocols 4.1.6 RS-232/422 Digital Serial Bus Four bi-directional serial ports are provided at the rear connector. Each serial port is individually software configurable for RS-232 or RS-422, and the following parameters:

Bus Speed (Min.):

Parity:

Data Bits:

Stop Bits:

Flow Control:

Up to and Including 19.2 Kbps None, Odd, Even 5, 6, 7, 8 1, 2 None, Xon/Xoff, RTS/CTS Page 16 Confidential and Proprietary to FLYHT Aerospace Solutions Ltd. 250-0019 Rev. --

22 April 2013 AFIRS 228 Series Installation Manual When a port is configured to RS-232, it conforms to the ANSI/TIA/EIA-232-F standard. When a port is configured to RS-422, it conforms to the TIA/EIA-422-B standard with the following additions:

Cable termination not required for typical applications (See TIA/EIA-422-B Annex A) Maximum Transceivers on Bus:

Receiver Input Impedance:

20 12 K 4.1.7 Ethernet Quantity:

Format:

4.1.8 Discrete Inputs Quantity:

Input Impedance:

Fault Current:

DIN+ Voltage Range:

Pulse Width (Min):

4 802.3 10BASE-T/100BASE-TX, half- and full-

duplex modes (auto-negotiated) ARINC 664P2 Physical Layer 16 Configurable

>10 k

<15 mA Logic High: 7.0 36.0 VDC Logic Low: 0 3.5 VDC 100 ms 4.1.8.1 Configurable Inputs Each configurable discrete input is individually software-configurable for the following:

Signal Level: Open-Ground (Negative-Seeking) or Open-28V (Positive-Seeking) Logic Assignment: Active Low or Active High Function: Selected from list. Refer to 7.13 for additional information on use of configurable inputs. 4.1.8.2 Remote Start Input In addition to the configurable discrete inputs, a Remote Start discrete input (J1C-5) is provided as a Negative-Seeking (Open/Ground) Active Low input with appropriate internal pull-up functionality. Refer to 7.3 for a description of the Remote Start functions. 4.1.9 Discrete Outputs Each discrete output transitions between an Open Circuit (high-impedance-to-ground) and a Closed Circuit (low-impedance-to-ground) state to indicate a change in output logic. Quantity:

Open Circuit Impedance:

Open Circuit Voltage (Max.):

8 Configurable

>100 k 36 VDC 250-0019 Rev. --

22 April 2013 Confidential and Proprietary to FLYHT Aerospace Solutions Ltd. Page 17 AFIRS 228 Series Installation Manual Closed Circuit Current Limit (Min.):

Voltage Across Closed Circuit:

500 mA

<1.25 V 4.1.9.1 Configurable Outputs The Discrete Outputs use Open-Closed signal levels, where the output is either high-

impedance to ground (Open) or low-impedance to ground (Closed). Each configurable discrete output is individually software-configurable for the following:

Logic Assignment: Active Low (Closed) or Active High (Open) Function: Selected from list. Refer to 7.14 for additional information on use of configurable outputs. 4.1.9.2 Fault Output The FAULT output is assigned to two rear connector pins, each meeting the same electrical criteria as a configurable output with the following functions:

The Normally Closed (N/C) FAULT output (J1B-13A) is Closed Circuit to Ground whenever any system fault is identified, including when the system is not powered. The Normally Open (N/O) FAULT output (J1B-13B) is Open Circuit (high impedance) whenever any system fault is identified, including when the system is not powered. 4.1.9.3 Chime Output The CHIME output goes to the Closed Circuit to Ground active state whenever the system is providing an aural alert in the cockpit (e.g. incoming voice call). The CHIME output is assigned to one aircraft interface connector pin (J1B-14B) meeting the following criteria:

Open Circuit Impedance:

Open Circuit Voltage (Max.):

Closed Circuit Current Limit (Min.):

Voltage Across Closed Circuit:

>100 k 36 VDC 2 A

<1.25 V 4.1.10 Two-Wire Phone Quantity:

Format:

Loop Battery:

Ring Signal:

Hook Flash:

Load Impedance (Nom.):

Polarity Sensitivity:

Audio Band Pass:

2 Standard 2-Wire Tip and Ring Loop 48 4 VDC 20 Hz 10%, 90 10 VAC RMS

<700 ms 600 None 300 3400 Hz Page 18 Confidential and Proprietary to FLYHT Aerospace Solutions Ltd. 250-0019 Rev. --

22 April 2013 AFIRS 228 Series Installation Manual 4.1.11 Microphone Input Quantity:

Format:

Dynamic Range:

Input Impedance:

Mic. Bias (No Load):

Mic. Bias Ripple:

Sidetone:

Sidetone Level:

Audio Band Pass:

Interphone Output Quantity:

Format:

Rated Output Impedance:

4.1.12 Rated Load Impedance:

Output Power Capability:

1 Standard DO-214 Microphone Input 20 mV to 1.5 V RMS 150 20%

16 0.5 V

<1 mV RMS in the 300 3400 Hz band Provided by System to Interphone Output Software Configurable 300 3400 Hz 1 Standard DO-214 Interphone Output

<30 across the frequency range 250 without system powered 50 across the frequency range

(capable of driving unbalanced load)

>40 mW RMS into 600

(software adjustable from 0.1 mW to max.)

>210 mW RMS into 50 10 mW RMS into 600 300 3400 Hz Output Power (As Shipped):

Audio Band Pass:

Iridium and GPS Antenna 4.1.13 Coaxial Cable Insertion Loss (Max.):

4.2 DMU Maintenance Connector (J2) The AFIRS DMU provides an RJ-45 Maintenance Port connector on the front panel which provides for Ethernet connection to Ground Service Equipment (GSE) e.g. a laptop or Personal Computer with a standard web browser. 3 dB @ 1626.5 MHz 250-0019 Rev. --

22 April 2013 Confidential and Proprietary to FLYHT Aerospace Solutions Ltd. Page 19 AFIRS 228 Series Installation Manual 4.3 Aircraft Configuration Module The ACM provides a 24-inch, color-coded, 4-conductor flying lead, which is terminated at the DMU rear connector (J1B) as per the following table:

Table 4-4 ACM Connections Termination J1B (MP) Function Color Orange/Violet Violet Green/Violet Blue/Violet 4.4 ARINC 429 Receiver Protocols ACM Power ACM Ground ACM Data ACM Clock 4J 4K 5J 5K 4.4.1 ACARS Communications Management Unit Source: ARINC 758 CMU Label 172 214 216 270 276 377 Parameter Subsystem Identifier ICAO 24-Bit Aircraft Address Word 1 ICAO 24-Bit Aircraft Address Word 2 Status Output 1 Status Output 2 Equipment Identifier Format SAL DISC DISC DISC DISC BCD Speed: Configurable Transmit Rate Core 1 s 1 s 1 s 1 s 1 s 1 s Parameter 4.4.2 Airbus Centralized Fault Display System (CFDS) Source: CFDIU Label 125 126 155 156 157 233 Time Flight Phase Aircraft Configuration Aircraft Type Aircraft Options Flight Number 1, 2 Format BCD BNR DISC DISC DISC BNR/BCD Speed: Configurable (Lo) Transmit Rate Core 1 s 1 s 1 s 1 s 1 s 4 s (SA)1 5 s (LR) Page 20 Confidential and Proprietary to FLYHT Aerospace Solutions Ltd. 250-0019 Rev. --

22 April 2013 AFIRS 228 Series Installation Manual 4.4.2 Airbus Centralized Fault Display System (CFDS) Source: CFDIU Label 234 Format BNR/BCD Flight Number 3, 4 Parameter 235 236 Flight Number 5, 6 Flight Number 7, 8 BNR/BCD BNR/BCD Speed: Configurable (Lo) Transmit Rate Core 4 s (SA)1 5 s (LR) 4 s (SA)1 5 s (LR) 4 s (SA)1 5 s (LR) 5 s (LR)1 BNR/BCD Flight Number 9,10 237 260G Date 301 302 303 304 Notes:

1. Airbus Single Aisle (SA) aircraft transmit Labels 233-236 every 4 seconds. Airbus Long Range (LR) Aircraft Identification 1-3 Aircraft Identification 4-6 Aircraft Identification 7-9 Fleet Identification, Aircraft Type BCD ISO 5 ISO 5 ISO 5 ISO 5 1 s 4 s 4 s 4 s 4 s aircraft transmit Labels 233-237 every 5 seconds. 4.4.3 Flight Management System ARINC 702/A Source: ARINC 702/A FMC Parameter Present Position Latitude Present Position Longitude Ground Speed Track Angle True Label 010 011 012 013 015 Wind Speed 016 Wind Direction True 061 062 063 074 075 125 Departure/Destination Airports (Dep1,2,3) Departure/Destination Airports (Dep4/Des1) Departure/Destination Airports (Des2,3,4) Zero Fuel Weight Gross Weight Universal Coordinated Time (UTC) Format BCD BCD BCD BCD BCD BCD BNR BNR BNR BNR BNR BCD Speed: Configurable Transmit Rate 500 ms 500 ms 500 ms 500 ms 500 ms 500 ms 1 s 1 s 1 s 1 s 200 ms 200 ms Core 2 2 2 2 250-0019 Rev. --

22 April 2013 Confidential and Proprietary to FLYHT Aerospace Solutions Ltd. Page 21 AFIRS 228 Series Installation Manual 4.4.3 Flight Management System ARINC 702/A Source: ARINC 702/A FMC Speed: Configurable Transmit Rate Parameter 1 s 1 s 1 s 1 s 1 s 1 s 1 s 200 ms 125 ms 500 ms 500 ms Format BNR BNR BNR BNR BNR/BCD BNR/BCD BNR/BCD BNR/BCD BNR/BCD Universal Coordinated Time (UTC) Computed Airspeed Total Air Temperature Static Air Temperature Flight Number (Characters 1,2) Flight Number (Characters 3,4) Flight Number (Characters 5,6) Flight Number (Characters 7,8) Flight Number (Characters 9,10) Label 150 206 211 213 233 234 235 236 237 2601 Date / Flight Leg Flight Number 261 Status Discretes 270 Present Position Latitude 310 Present Position Longitude 311 Ground Speed 312 Track Angle True 313 314 True Heading 315 Wind Speed 316 Wind Direction True 317 320 Magnetic Heading Flight Information 360 Notes:

1. Because of the potential conflict between systems that could output either the year or the flight leg Core 2 2 2 2 200 ms 200 ms 200 ms 50 ms 50 ms 50 ms 100 ms 50 ms 50 ms 50 ms BCD BCD DISC BNR BNR BNR BNR BNR BNR BNR BNR BNR BNR Track Angle Magnetic 1 s number in this word, only the day and month portions of the date are used. 2. Either the BNR or BCD label (not both) is required for Latitude, Longitude, Groundspeed and UTC. Page 22 Confidential and Proprietary to FLYHT Aerospace Solutions Ltd. 250-0019 Rev. --

22 April 2013 AFIRS 228 Series Installation Manual Parameter Pressure Altitude Baro Corrected Altitude True Airspeed Static Air Temperature 4.4.4 Flight Management System GAMA 429 Source: GAMA 429 FMC Label1 012 Ground Speed 074G Data Record Header 075G Active WPT From/To Data 113G Message Checksum 125 Universal Coordinated Time (UTC) 150 Universal Coordinated Time (UTC) 203 204 210 213 260G Date 275G Status Word 300G Station Magnetic Dec. Type & Class 301G Message Characters 7-9 302G Message Characters 10-12 303G Message Length / Type / Number 304G Message Characters 1-3 305G Message Characters 4-6 306G NAV/WPT/AP Latitude 307G NAV/WPT/AP Longitude 310 311 312 Ground Speed Track Angle True 313 314 True Heading 315 Wind Speed 316 Wind Direction True 320 Magnetic Heading 352G Estimated Time to Destination 371G Equipment Identifier Present Position Latitude Present Position Longitude Format BCD BNR DISC BNR BCD BNR BNR BNR BNR BNR BCD DISC BNR BNR BNR BNR BNR BNR BNR BNR BNR BNR BNR BNR BNR BNR BNR BNR BNR DISC Speed: Configurable Transmit Rate 500 ms Note 2 Note 2 Note 3 200 ms 100 ms 1 s 62.5 ms 125 ms 500 ms 1 s 400 ms Note 3 Note 3 Note 3 Note 3 Note 3 Note 3 Note 3 Note 3 200 ms 200 ms 50 ms 50 ms 50 ms 100 ms 100 ms 50 ms 1 s 1 s Core 4 4 4 4 250-0019 Rev. --

22 April 2013 Confidential and Proprietary to FLYHT Aerospace Solutions Ltd. Page 23 AFIRS 228 Series Installation Manual 4.4.4 Flight Management System GAMA 429 Notes:

1. Labels with a G suffix are defined in GAMA Publication No. 11. 2. These labels are transmitted once at the beginning of each flightplan/graphics map data transfer. Refer to GAMA Publication No. 11 for further information. 3. These labels are used to make up the individual records that comprise a flightplan/graphics map data transfer. Not all labels are transmitted with each record. Ten records are transmitted in one second. Refer to GAMA Publication No. 11 Addendum 3 for further information. 4. Either the BNR or BCD label (not both) is required for Groundspeed and UTC. 4.4.5 Flight Management System CMA-9000 Source: FMC General Broadcast Output Bus Parameter ETA At Destination Departure/Destination Airports (Dep1,2,3) Departure/Destination Airports (Dep4/Des1) Departure/Destination Airports (Des2,3,4) Zero Fuel Weight Label 056 061 062 063 074 075 Gross Weight 076 GPS Altitude 150 203 204 205 Mach Number 206 210 213 233 234 235 236 237 260 261 Universal Coordinated Time (UTC) Pressure Altitude Baro Corrected Altitude Computed / Indicated Airspeed True Airspeed Static Air Temperature Flight Number (Characters 1,2) Flight Number (Characters 3,4) Flight Number (Characters 5,6) Flight Number (Characters 7,8) Flight Number (Characters 9,10) Date / Flight Leg Flight Number Format BCD BNR BNR BNR BNR BNR BNR BNR BNR BNR BNR BNR BNR BNR BNR/BCD BNR/BCD BNR/BCD BNR/BCD BNR/BCD BCD BCD Speed: Configurable Transmit Rate Core 1 s 1 s 1 s 1 s 1 s 1 s 1 s 500 ms 500 ms 500 ms 1 s 1 s 500 ms 1 s 1 s 1 s 1 s 1 s 1 s 1 s 1 s Page 24 Confidential and Proprietary to FLYHT Aerospace Solutions Ltd. 250-0019 Rev. --

22 April 2013 AFIRS 228 Series Installation Manual 4.4.5 Flight Management System CMA-9000 Source: FMC General Broadcast Output Bus Parameter FMS Status Word 1 Present Position Latitude Present Position Longitude Label 270 310 311 312 Ground Speed Track Angle True 313 True Heading 314 315 Wind Speed 316 Wind Direction True 317 320 Magnetic Heading Track Angle Magnetic 4.4.6 Basic DTP Source: Generic Date/Time/Position Source Parameter Universal Coordinated Time (UTC) Label 150 260G Date 310 311 Present Position Latitude Present Position Longitude Speed: Configurable Transmit Rate Core 1 s 500 ms 500 ms 500 ms 500 ms 500 ms 500 ms 500 ms 500 ms 500 ms Format DISC BNR BNR BNR BNR BNR BNR BNR BNR BNR Speed: Configurable Transmit Rate Core 1 s 1 s 200 ms 200 ms Format BNR BCD BNR BNR Parameter IOC GPBUS 5 Universal Coordinated Time (UTC) Pressure Altitude 4.4.7 Pro Line 4/21 I/O Concentrator (GP Bus 5) Source:

Label 151 203 205 Mach Number 206 211 261 310 Computed / Indicated Airspeed Total Air Temperature Date Present Position Latitude Format BNR BNR BNR BNR BNR BCD BNR 250-0019 Rev. --

22 April 2013 Confidential and Proprietary to FLYHT Aerospace Solutions Ltd. Speed: High Transmit Rate Core 1 s 50 ms 100 ms 50 ms 400 ms 1 s 200 ms Page 25 AFIRS 228 Series Installation Manual IOC GPBUS 5 4.4.7 Pro Line 4/21 I/O Concentrator (GP Bus 5) Source:

Label Parameter 311 Present Position Longitude 312 Ground Speed 313 Track Angle True 314 True Heading 315 Wind Speed 320 Magnetic Heading Format BNR BNR BNR BNR BNR BNR Speed: High Transmit Rate Core 200 ms 200 ms 100 ms 100 ms 500 ms 19 ms 4.4.8 Multi-Purpose Control Display Unit Source: ARINC 739A MCDU Label 270 MCDU Normal Discrete Word 377 Equipment Identifier Parameter 4.4.9 Mode S Transponder Source: ARINC 718A Mode S Transponder Label 203 204 233 234 235 236 237 275 276 Parameter Altitude Baro Corrected Altitude Flight ID (Characters 1,2) Flight ID (Characters 3,4) Flight ID (Characters 5,6) Flight ID (Characters 7,8) Flight ID (Characters 9,10) TCAS Control (Mode S Address Part 1) TCAS Control (Mode S Address Part 2) Speed: Configurable Transmit Rate Core 1 s 1 s Format DISC DISC Format BNR BNR BNR/BCD BNR/BCD BNR/BCD BNR/BCD BNR/BCD DISC DISC Speed: Configurable Transmit Rate Core 100 ms 100 ms 1 s 1 s 1 s 1 s 1 s 100 ms 100 ms Page 26 Confidential and Proprietary to FLYHT Aerospace Solutions Ltd. 250-0019 Rev. --

22 April 2013 AFIRS 228 Series Installation Manual 4.5 ARINC 429 Receiver Activity Status Table 4-5 defines the criteria the AFIRS 228 Series uses for determining whether a receiver port is active. A bus is generally declared active when 4 consecutive words at the specified rate are received and declared inactive when 4 consecutive samples fail. Table 4-5 ARINC 429 Receiver Port Monitoring Receiver ACARS Airbus CFDS FMS (A702/A, CMA-9000) FMS (GAMA 429) Basic DTP PL4/21 GPBus5 A739 MCDU Mode S Transponder Activity Label Min. Update Rate 270 125 / 260 270 / 275 275 310 / 311 310 / 311 270 / 377 275 1 Hz 1 Hz 1 Hz 1 Hz 1 Hz 1 Hz 1 Hz 1 Hz 4.6 ARINC 429 Transmitter Protocols 4.6.1 ACARS Output Bus Destin: ARINC 758 CMU Label 172 270 Parameter Subsystem Identifier Status Word 4.6.2 General Purpose Output Bus Destin: Various Label 172 270 377 Parameter Subsystem Identifier Status Word Equipment Identifier Speed: Configurable Transmit Rate Update Rate 1 s 1 s 1 s Format SAL DISC Speed: Configurable Transmit Rate Update Rate 1 s 1 s 1 s 1 s Format SAL DISC BCD 250-0019 Rev. --

22 April 2013 Confidential and Proprietary to FLYHT Aerospace Solutions Ltd. Page 27 AFIRS 228 Series Installation Manual 4.6.3 A739 MCDU Output Bus Destin: ARINC 739A MCDU Label 172 377 Parameter Subsystem Identifier Equipment Identifier Speed: Configurable Transmit Rate Update Rate 1 s 1 s Format SAL BCD 4.6.4 Airbus Centralized Fault Display System (CFDS) Output Bus Destin: Airbus CFDIU Speed: Configurable Parameter Label 354 3561 377 Notes:

1. Label 356 is only transmitted when the system is in Operational or Maintenance mode and there are Format Transmit Rate Update Rate ISO-5 ISO-5 BCD LRU Identification Fault Status Equipment Identifier 500 ms 200 ms 1 s 1 s no active failures or faults. Page 28 Confidential and Proprietary to FLYHT Aerospace Solutions Ltd. 250-0019 Rev. --

22 April 2013 AFIRS 228 Series Installation Manual INSTALLATION CONSIDERATIONS 5. This section provides information on the installation considerations for each of the AFIRS 228 Series system components. 5.1 Data Management Unit (DMU) The DMU is housed in an ARINC 600 2MCU enclosure, which is designed to be mounted in a standard ARINC 600 mounting tray. Figure 5-1 shows a typical ARINC 600 2MCU tray used for the AFIRS DMU. Figure 5-1 2MCU Mounting Tray While the DMU does not require forced-air cooling, every attempt should be made to place the DMU in a benign and well-ventilated environment. Placing the DMU on a plenum shelf in the Electronics Bay of the aircraft and using a mounting tray that provides cooling air to the DMU is preferred. The DMU tray should be electrically bonded to the airframe (<10 milliohms). It is recommended that the DMU be located where easy front panel access is available to facilitate replacing the flash card or connecting to the Maintenance Port. 250-0019 Rev. --

22 April 2013 Confidential and Proprietary to FLYHT Aerospace Solutions Ltd. Page 29 AFIRS 228 Series Installation Manual 5.2 Aircraft Configuration Module (ACM) The ACM can be mounted on or near the DMU tray within 24 inches of the DMU rear connector. The ACM should be electrically bonded to the airframe (<10 milliohms). It is recommended that the ACM be located to provide easy access to the cover if ever the SIM card requires replacement. Refer to Figure 3-2 for the ACM mounting footprint. 5.3 AFIRS Antenna System The AFIRS 228 Series system has a single combined Iridium/GPS RF connection on the rear interface connector, which is to be connected to a single combined Iridium/GPS Antenna. The antenna system is comprised of all the components from the rear interface connector up to and including the antenna. The total gain of the antenna system must be greater than 0 dB at 1626.5 MHz (measured at the antenna zenith). Most Iridium antennas have a gain of +3 dBic at the zenith; therefore the maximum attenuation in the rest of the antenna system must be less than 3 dB. If an antenna with a different gain is selected, the maximum loss of the rest of the antenna system must be adjusted accordingly. 5.3.1 Antenna The antenna is to be selected by the system integrator to be suitable for the installed aircraft environment. See 3.3 for antenna selection criteria. 5.3.2 Antenna Location The antenna must be mounted in a location with a clear view of the sky. The typical mounting location is on top of the fuselage as close to the AFIRS DMU as possible. The AFIRS antenna should be kept a minimum of 5 feet from GPS antennas and a minimum of 3 feet from all other antennas, unless analyses and tests demonstrate that there is no mutual interference when separation is reduced. If the aircraft is equipped with a high-gain INMARSAT Satcom system (e.g. Aero-I, Aero-H, etc.), the separation between the high-gain INMARSAT antenna and the AFIRS antenna must be maximized, preferably >45 feet. Typically, a filter is also required to mitigate the interference from the INMARSAT system (ref. 5.3.5). If the aircraft is equipped with a low-gain INMARSAT Satcom system (e.g. Aero-C, Sat-AFIS, etc.), the separation between the low-gain INMARSAT antenna and the AFIRS antenna should be at least 10 feet. Typically, a filter is also required to mitigate the interference from the INMARSAT system (ref. 5.3.5). 5.3.3 Antenna Mounting The system integrator is responsible to mount the antenna to the airframe using methods that meet all of the applicable airworthiness requirements. If the antenna is mounted off the centerline of the fuselage (e.g. to avoid a stringer) or on a surface that is not parallel with the longitudinal axis of the aircraft (e.g. a fairing), a shim should be used to keep the antenna tilt angle to 5 or less in both the lateral and longitudinal axes for optimal performance. The antenna must be installed in a manner that prevents harmful levels of lightning energy from entering the AFIRS system through the coaxial cable. This is can be accomplished by selecting Page 30 Confidential and Proprietary to FLYHT Aerospace Solutions Ltd. 250-0019 Rev. --

22 April 2013 AFIRS 228 Series Installation Manual an antenna that has been tested for direct lightning effects in accordance with DO-160, and then electrically bonding the antenna to the airframe (<10 milliohms). For metal airframes, this can be accomplished by direct metal-to-metal contact between the antenna, the mounting shim (if used) and the airframe. The airframe structure should not be painted, and fay sealing should not be used between the antenna, the shim, and airframe. For mounting on non-metallic fairings, a low-impedance ground plane (minimum 6-inches wide) should be provided to the adjacent metallic structure. For composite airframes, refer to the airframe manufacturers instructions for acceptable methods to install the AFIRS antenna. 5.3.4 Coaxial Cable The coaxial cable used between the rear interface connector and the antenna is a critical component of the antenna system. The coaxial cable must meet all the environmental and flammability requirements applicable to the Electrical Wiring Interconnection System (EWIS) of the given aircraft. It must also minimize signal attenuation. Large diameter low-loss cables cannot be connected directly to the ARINC 600 Size 5 contact on the AFIRS rear electrical connector, so a stub coaxial cable is often required. Shelf disconnect panels on modern transport category aircraft provide a convenient location to transition from the stub coaxial cable to the low-loss cable. It is recommended that cable breaks be kept to a minimum, as each connection typically adds approximately 0.1 dB of insertion loss. FLYHT recommends the following coaxial cable types be used in aircraft installations. Alternate cables and connectors that meet the attenuation and EWIS requirements are also acceptable. Table 5-1 Coaxial Cable Types Cable Part Number Vendor Attenuation

(dB/100 ft) 310701 310801 311201 311501 S22089 S55122 S33141 ECS ECS ECS ECS PIC PIC PIC 3.9 4.6 6.7 9.1 4.5 6.6 8.6 Size 5 Contact P922 190303 TNC Bulkhead BTS002 BTS022 BTS122 BTS922 190421 190621 190321 TNC Connector CTS002 CTS022 CTS122 CTS922 190409 190609 190308 90 TNC Connector CTR002 CTR022 CTR122 CTR922 190408 190608 190309 250-0019 Rev. --

22 April 2013 Confidential and Proprietary to FLYHT Aerospace Solutions Ltd. Page 31 AFIRS 228 Series Installation Manual Cable Part Number Vendor Attenuation

(dB/100 ft) TFLX480-100 Emteq TFLX410-100 Emteq TFLX295-100 Emteq TFLX165-100 Emteq 4.8 5.2 7.6 17.0 Size 5 Contact A65165-1 TNC Bulkhead TFS488-2 TFS410-2 TFS295-2 TFS165-2 TNC Connector TMS488-1 TMS410-1 TMS295-1 TMS165-1 90 TNC Connector TMR488-1 TMR410-1 TMR295-1 TMR165-1 For example, a cable installation consisting of a P922 contact, 2 feet of 311501 cable, a BTS922 connector mated to a CTS022 connector, 30 feet of 310801 cable, and a CTR022 connector would result in:

0.10 + 0.18 + 0.10 + 1.38 + 0.10 = 1.86 dB attenuation INMARSAT Filter FLYHT recommends that every effort be made to minimize cable attenuation, as this improves the link margin and performance of the satellite system. When the aircraft is also equipped with an INMARSAT Satcom system, keeping the antenna system attenuation below 2.0 dB (1.0 dB for the filter and 1.0 dB for the coaxial cable) significantly improves the mitigation of interference. 5.3.5 When the aircraft is also equipped with an INMARSAT Satcom system, a filter is generally required to be installed in the AFIRS antenna system to mitigate the interference from the INMARSAT system. These filters generally have an insertion loss of 1.0 1.2 dB and this must be taken into account in the total antenna system attenuation calculation. Due to the complexities associated with concurrent Iridium and INMARSAT system installations, FLYHT recommends that system integrators who are planning these types of installations contact FLYHTs Engineering Department for guidance and assistance. Page 32 Confidential and Proprietary to FLYHT Aerospace Solutions Ltd. 250-0019 Rev. --

22 April 2013 AFIRS 228 Series Installation Manual INSTALLATION MATERIALS 6. In addition to the AFIRS 228 Series LRUs (DMU and ACM), the materials described in this section are generally required as part of a typical AFIRS 228 Series system installation. Note:

The system integrator is responsible to ensure that all installation materials used meet the regulatory requirements for the intended aircraft installation environment. 6.1 Required Materials ARINC 600 2MCU mounting tray ARINC 600 Size 2 connector, with contacts ARINC 600 ground block, with contacts AFIRS antenna (ref. 3.3) Antenna coaxial cable(s) (ref. 5.3.4) System interface wiring (ref. 7) The following table provides typical part numbers for installation materials. Table 6-1 Installation Materials Description Mounting Tray, No Cooling Mounting Tray, Plenum Connector, ARINC 600 Connector1, ARINC 600, With #6-32 Clinch Nuts Contact, #12 Reduced Barrel Contact, ARINC 600 Size 5 Ground Block1, ARINC Part Number 6012-102 6064-102 NSXN2P201S0004 NSXN2P201S0104 Vendor Qty. ECS Radiall 1 1 620 341 P922 RBGP48-116N (Souriau) S280W601-116 (Boeing) M39029/1-101 5 1 Radiall ECS Burndy

(Souriau) 1 50 Contact, Ground Block Notes:

1. Connector with clinch nuts cannot be used in conjunction with ARINC ground block. 250-0019 Rev. --

22 April 2013 Confidential and Proprietary to FLYHT Aerospace Solutions Ltd. Page 33 AFIRS 228 Series Installation Manual 6.2 Additional Materials Depending on the architecture of the systems being interfaced to, the following materials may be required. AFIRS FAULT Annunciator (ref. 7.4) AFIRS Status Annunciators (ref. 7.14 and 7.15) AFIRS Control Switches (ref. 7.13 and 7.15) Page 34 Confidential and Proprietary to FLYHT Aerospace Solutions Ltd. 250-0019 Rev. --

22 April 2013 AFIRS 228 Series Installation Manual 7. SYSTEM INTERFACE WIRING This section provides information on the system interface wiring required for the AFIRS 228 Series System. 7.1 General All wire types and installation practices must comply with the EWIS requirements for the aircraft

(ref. FAR 26 Subparts B & D). Unless otherwise noted, minimum wire size is 22 AWG for standard copper wire or 24 AWG for high strength copper alloy wire. Terminate all shields at ground block or ground stud on DMU tray. Keep shield drains and unshielded conductor lengths as short as practicable (<3). 7.2 Primary Power, Antenna, and ACM The primary power, antenna, and ACM connections shown in Figure 7-1 are required for all AFIRS 228 system installations. The system will start and continue to operate whenever power

(20.5 32.2 VDC) is available at the Primary Power Input pin (J1C-2). Figure 7-1 Primary Power, Antenna and ACM Interface 250-0019 Rev. --

22 April 2013 Confidential and Proprietary to FLYHT Aerospace Solutions Ltd. Page 35 AFIRS 228 Series Installation Manual 7.3 Alternate Power Alternate Power and Remote Start are optional connections (see Figure 7-2). When power is applied to the Alternate Power Input pin (J1C-9) and the Remote Start Input pin (J1C-5) is held in the Active Lo state for >100 ms, the system will run on the Alternate Power. If both the Primary and Alternate power sources are available, the system will use the Primary Power Input. Figure 7-2 Alternate Power Interface 7.3.1 Redundant Power Supply One use of the Alternate Power Input is to provide redundant power supply to the AFIRS system. In this scenario, the Primary Power Input can be connected to a 28 VDC Main Bus and the Alternate Power Input connected to a Secondary Bus, Battery Bus, or dedicated AFIRS battery pack. The Remote Start Input is connected to ground. The AFIRS will operate on the Primary Power Input, but if Primary Power is lost, the system will continue to operate from the Alternate Power Input. A software-configurable timer can be used to automatically shut the AFIRS system down after a specified time (0 30 minutes). The timer can also be set to Always On. 7.3.2 Remote Start Another use of the Alternate Power Input is to provide remote start capability to the AFIRS system. In this scenario, the Primary Power Input can be connected to a 28 VDC Main Bus and the Alternate Power Input connected to a Battery Bus or dedicated AFIRS battery pack. When a Page 36 Confidential and Proprietary to FLYHT Aerospace Solutions Ltd. 250-0019 Rev. --

22 April 2013 AFIRS 228 Series Installation Manual momentary ground (<100 ms) is applied to the Remote Start Input, the system will start and operate from the Alternate Power Input. The software-configurable timer can be used to automatically turn the system off if Primary Power is not provided in the specified time. One use of this configuration is to monitor Auxiliary Power Unit (APU) start times. If the Remote Start Input is connected to the APU start logic, the AFIRS will start when the APU starts. Even if the main aircraft power is not turned on, the AFIRS can log the APU start event and advise operators if an APU is left running for an extended time. 7.4 Fault Indicator The system integrator should provide an AFIRS FAULT indication in the cockpit. This may be provided by an ARINC 429 interface to a centralized crew alerting system, or by using a discrete Fault output from the AFIRS. The AFIRS 228 provides two separate fault outputs, a normally closed (N/C) and a normally open (N/O). 7.4.1 Fault Output (N/C) The N/C fault output provides a ground whenever there is a system fault, including if the system is not powered. This is the preferred output for most installations. See Figure 7-3. Figure 7-3 Fault (N/C) Interface 7.4.2 Fault Output (N/O) The N/O fault output provides an open circuit whenever there is a system fault, including if the system is not powered, and provides a ground when there is no fault. This interface is primarily intended for backwards compatibility for retrofit of existing AFIRS 220 systems. See Figure 7-4. Figure 7-4 Fault (N/O) Interface 250-0019 Rev. --

22 April 2013 Confidential and Proprietary to FLYHT Aerospace Solutions Ltd. Page 37 AFIRS 228 Series Installation Manual 7.5 Flight Data Monitoring The AFIRS 228 may be connected to an ARINC 573/717 databus in the aircraft for monitoring and recording information on this databus. This interface is software-configurable to support 64, 128, 256, 512, and 1024 WPS data rates, as well as Harvard Bi-Phase or Bipolar-Return-To-

Zero encoding. See Figure 7-5. Figure 7-5 ARINC 717 Interface 7.6 ARINC 429 Interfaces The AFIRS 228 has 16 ARINC 429 receive ports and 6 ARINC 429 transmit ports. Each port is software-configurable for high or low speed, and the receive ports are also individually software-

configurable for odd, even or no parity checking. (The transmit ports always transmit odd parity.) 7.6.1 Receiver Protocols Each of the ARINC 429 receivers can be configured in software for the proper protocol of the external aircraft system to which it is interfaced. Below is a list of the available ARINC 429 receiver protocols. (See 4.4 for the label specifications for each receiver protocol.) Once a protocol (except None or Generic 429) is selected for any given receive port, it is no longer available for assignment to any of the other ports. None Generic 429 ACARS 1 ACARS 2 Airbus CFDS FMS 1 A702/A, GAMA 429, CMA-9000, Basic DTP FMS 2 A702/A, GAMA 429, CMA-9000, Basic DTP FMS 3 A702/A, GAMA 429, CMA-9000 PL4/21 GPBUS5 1 PL4/21 GPBUS5 2 A739 MCDU 1 Page 38 Confidential and Proprietary to FLYHT Aerospace Solutions Ltd. 250-0019 Rev. --

22 April 2013 AFIRS 228 Series Installation Manual A739 MCDU 2 A739 MCDU 3 Mode S Transponder 1 Mode S Transponder 2 When an input is not connected to an active system (e.g. no connection, or wiring provisions only are installed), the port should be configured as None to avoid triggering nuisance bus inactivity faults. 7.6.2 Transmitter Protocols Each of the ARINC 429 transmitters can be configured in software for the proper protocol of the external aircraft system to which it is interfaced. Below is a list of the available ARINC 429 transmitter protocols. (See 4.6 for the label specifications for each transmitter protocol.) Once a protocol (except None) is selected for any given port, it is no longer available for assignment to any of the other ports. None ACARS (AFIRS 228S Only) GP Bus 1 GP Bus 2 GP Bus 3 GP Bus 4 A739 MCDU Airbus CFDS 7.7 MCDU If an ARINC 739A MCDU is installed, MCDU 1 should be connected to ARINC 429 Tx 1 and ARINC 429 Rx 1. For MCDU 2 and 3, ARINC 429 Rx ports 2 and 3 are used in Figure 7-6 below, but any Rx port from 2 to 16 may be used. 250-0019 Rev. --

22 April 2013 Confidential and Proprietary to FLYHT Aerospace Solutions Ltd. Page 39 AFIRS 228 Series Installation Manual J1B (MP) ARINC 429 Rx 1 ARINC 429 Tx 1 ARINC 429 Rx 2 A B A B A B 1G 1H 1J 1K 3C 3D ARINC 429 Rx 3 A B 3E 3F DMU Figure 7-6 MCDU Interface ARINC 429 Tx ARINC 429 Rx ARINC 429 Tx ARINC 429 Rx ARINC 429 Tx ARINC 429 Rx A B A B MCDU 1 A B A B MCDU 2 A B A B MCDU 3 ICAO Address 7.8 The AFIRS 228 uses the aircrafts ICAO address as the primary method of identifying the originating aircraft for non-safety services reports it sends to Uptime. It is therefore important that the correct ICAO address be available from one of the following sources. (The sources are listed in the order of priority used by the AFIRS 228.) ACARS CMU 1 ACARS CMU 2 Mode S Transponder 1 Mode S Transponder 2 Owner Requirements Table (ORT) stored in the ACM Page 40 Confidential and Proprietary to FLYHT Aerospace Solutions Ltd. 250-0019 Rev. --

22 April 2013 AFIRS 228 Series Installation Manual While it is not required for the AFIRS 228 to receive the ICAO address from a CMU or Mode S Transponder (manually programming the ORT with the correct ICAO address will provide proper system functionality), using at least one of these interfaces ensures that the AFIRS 228 is using the same ICAO address that is programmed into the other aircraft systems. Whenever the AFIRS 228 detects that the ICAO address from the interfaced system is different than that stored in the ORT and that the new address is valid (i.e. not 000000 or FFFFFF), it will automatically update the ICAO address stored in the ORT with the new address. If the aircrafts registration is ever changed (and the CMU and/or Mode S Transponder addresses are re-

strapped accordingly), no additional maintenance tasks are then required for the AFIRS 228 to use the new ICAO address. The system integrator may use none or any combination of the four external system interface options, depending on the availability of compatible system interfaces and the degree of redundancy desired. 7.8.1 ACARS CMU The ACARS ARINC 429 Tx interface will provide safety-services data functionality for the AFIRS 228S, but it is provisions-only for AFIRS 228B. It is recommended that the wires be capped and stowed near the connectors as shown. ARINC 429 Rx ports 4 and 5 are shown in Figure 7-7 below, but any Rx port from 2 to 16 may be used. Figure 7-7 ACARS Interface 250-0019 Rev. --

22 April 2013 Confidential and Proprietary to FLYHT Aerospace Solutions Ltd. Page 41 AFIRS 228 Series Installation Manual 7.8.2 Mode S Transponder ARINC 429 Rx ports 6 and 7 are shown in Figure 7-8 below, but any Rx port from 2 to 16 may be used. Figure 7-8 Mode S Transponder Interface 7.9 Date, Time and Position The AFIRS 228 uses date, time and position information for numerous purposes, including information tags attached to various reports and events. Date, time and position information can be provided by the following sources. (The sources are listed in the order of priority used by the AFIRS 228.) External Source 1 (FMS, GPS, etc.) External Source 2 (FMS, GPS, etc.) External Source 3 (FMS, GPS, etc.) While it is not required for the AFIRS 228 to receive date, time and position information from any external sources, doing so provides a more robust system design and it is recommended that at least one external position source be connected if a compatible system interface is available. The system integrator may use none or any combination of the three external system interface options, depending on the availability of compatible system interfaces and the degree of redundancy desired. The ARINC 429 Receiver table in Appendix A identifies the ARINC 429 receiver protocols that AFIRS can use for DTP information. Internal GPS Page 42 Confidential and Proprietary to FLYHT Aerospace Solutions Ltd. 250-0019 Rev. --

22 April 2013 AFIRS 228 Series Installation Manual 7.10 Generic ARINC 429 Interfaces The Generic 429 protocol allows customizable software components in the AFIRS to access raw ARINC 429 data from systems whose label definitions are not predefined. Connection and use of generic ARINC 429 interfaces should only be done in conjunction with FLYHT engineering support. The General Purpose Output Bus protocol may be used to provide AFIRS 228 status information to other aircraft systems (e.g. EICAS, ECAM, CMC, etc.) Presently, none of these interfaces have been tested by FLYHT, and the system integrator must coordinate with FLYHT engineering support prior to using this transmitter protocol. 7.11 RS-232/422 Databus The AFIRS 228 has four serial ports (transmit and receive). Each port is software-configurable for RS-232 or RS-422 mode. The speed, data bits, parity, stop bits, and flow control settings for each port are also software-configurable. See Figure 7-9. Each serial port is assigned 5 pins on the rear connector. The function of these pins is dependent on whether RS-232 or RS-422 mode is being used. Table 7-1 Serial Port Pin Assignments Port 3 10C 10D 10E 10F 9B Port 2 9J 9K 10A 10B 9A Port 1 9E 9F 9G 9H 7J Port 4 10G 10H 10J 10K 7K RS-422 Tx-

Tx+

Rx+

Rx-

Not Used RS-232 TXD RTS RXD CTS Com When configured for RS-232 mode, the serial ports support software (Xon/Xoff) and hardware

(RTS/CTS) handshaking. If hardware handshaking is not being used, the RTS and CTS pins do not need to be connected. Each of the serial ports can be configured in software for the proper protocol of the external aircraft system to which it is interfaced. Below is a list of the available protocols. Once a protocol

(except None or Generic) is selected for any given port, it is no longer available for assignment to the other ports. Unused serial ports should be configured as None. None Generic EFB 1 EFB 2 EFB 3 250-0019 Rev. --

22 April 2013 Confidential and Proprietary to FLYHT Aerospace Solutions Ltd. Page 43 AFIRS 228 Series Installation Manual Figure 7-9 Serial Port Interface 7.12 Ethernet The AFIRS 228 has four Ethernet ports (see Figure 7-10). Each port can auto-negotiate the best speed (10/100) and mode (full/half duplex). Port 1A is reserved for future use and is currently not configurable. Ports 2B, 3B, 4B and the Maintenance Port are connected to a second subnet through an internal managed switch. The installation design should consider that the IP settings for Port 1A will be different than those for Ports 2B, 3B, and 4B. Therefore, when identical configuration settings for a group of devices are desired, they should all be connected to Ports 2B, 3B and 4B. For example, if EFB 1 and EFB 2 were connected to Ports 1A and 2B respectively, they would need to be configured with different IP settings. If the device locations were exchanged (which would be common for Class 2 EFBs), neither EFB connections would work until the EFBs were reconfigured. In this scenario, the preferred design would be to connect the EFBs to Ports 2B and 3B, making their IP configurations identical. Now if the device locations were swapped, both EFBs connections would still work without the need to reconfigure the devices. A 4-conductor Ethernet cable that meets the aircrafts EWIS requirements must be used. The rear connector pin layout provides slightly better noise immunity with a star-quad cable construction, but a twisted-pair cable construction can generally also be used. For star-quad Page 44 Confidential and Proprietary to FLYHT Aerospace Solutions Ltd. 250-0019 Rev. --

22 April 2013 AFIRS 228 Series Installation Manual cables, the conductor lay order should be maintained without crossing the conductors when terminating. For twisted-pair construction, the conductor twists should be maintained right up to the rear connector. In either case, the best noise immunity is obtained by keeping the strip length of the shield as short as physically possible, preferably <0.25 inches. PIC P/N E51424 and ECS P/N 422404 are examples of aircraft-quality star-quad Ethernet cables that are typically suitable for use. PIC P/N E40424 and ECS P/N 922404 are examples of aircraft-quality twisted-pair Ethernet cables that are typically suitable for use. Each of the Ethernet ports can be configured in software for the proper protocol of the external aircraft system to which it is interfaced. Below is a list of the available protocols. None Not Monitored Monitored Unused Ethernet ports should be configured as None. A Monitored port is one where the AFIRS expects to see an active link and it will generate an error report if the Ethernet link to the external system is not available. For example, if the AFIRS is connected by Ethernet to a Class 2 EFB that is routinely turned off and stowed for take-off and landing, the port should be configured as Not Monitored or the AFIRS will generate a nuisance fault whenever the EFB is not powered. Figure 7-10 Ethernet Interface 250-0019 Rev. --

22 April 2013 Confidential and Proprietary to FLYHT Aerospace Solutions Ltd. Page 45 AFIRS 228 Series Installation Manual 7.13 Discrete Inputs The AFIRS has 14 configurable Discrete Inputs, each of which is software-configurable for Open-Ground or Open-28V signaling levels, Active High or Active Low logic, and the assigned function. 7.13.1 Weight-On-Wheels Input Discrete Input No. 1 (Din 1) is dedicated for use as a Weight on Wheels (WOW1) input. When there is only one WOW input (i.e. the WOW2 function is not assigned to a Discrete Input; see 7.13.4) and the WOW1 input transitions to the active state, the AFIRS is signaled that the aircraft is on the ground, and the inactive state indicates that the aircraft is in the air. WOW1 (Din 1) is only an Open-Ground input; it cannot be configured as an Open-28V input. A Hardware Programming Pin (HPP) is provided to set whether the WOW1 input is Active High or Active Low. If the WOW HPP pin (J1B-11F) is not connected, WOW1 is configured as an Active Low input, i.e. Ground = On Ground. If the WOW HPP pin is connected to ground, WOW1 is configured as an Active High input, i.e. Ground = In Air. If one of the configurable Discrete Inputs is configured for the WOW2 function (see 7.13.4), the following logic is used to determine the aircrafts Air-Ground status:

When the WOW1 discrete input is in the active state (as configured by the WOW HPP strapping) and the WOW2 discrete input is in the active state (as defined by the ICT setting for the discrete input configured as WOW 2), the aircraft is considered as Weight On Wheels. When any of the WOW discrete inputs are in the inactive state, the aircraft is considered as Weight Off Wheels. 7.13.2 Signal Level Configuration Each configurable Discrete Input is software-configurable for Open-Ground or Open-28V signaling levels. When configured as Open-Ground, the input is pulled-up to 28V internally (High State) and applying a ground input (<3.5 V) transitions the input to the Low State. When configured as Open-28V, the input is pulled-down to 0V internally (Low State) and applying a voltage signal to the input (>7.0 V) transitions the input to the High State. 7.13.3 Logic Configuration Each configurable Discrete Input is software-configurable for Active Low or Active High signaling levels. See Table 7-2. When configured as Active Low, the function is considered to be active when the input is in the Low State (<3.5V). When configured as Active High, the function is considered to be active when the input is in the High State (>7.0V). Page 46 Confidential and Proprietary to FLYHT Aerospace Solutions Ltd. 250-0019 Rev. --

22 April 2013 AFIRS 228 Series Installation Manual Table 7-2 Discrete Input Configurable States Electrical Characteristic Logic Assignment Description Negative-Seeking

(Open-Ground) Pulled Up to 28 V Active Low The input function is considered to be in its active state when the input is in the Logic Low voltage range (<3.5 V). Active High The input function is considered to be in its active state when the input is in the Logic High voltage range (>7.0 V). Positive -Seeking

(Open-28 V) Pulled Down to 0 V Active High The input function is considered to be in its active state when the input is in the Logic High voltage range (>7.0 V). The input function is considered to be in its active state when the input is in the Logic Low voltage range (<3.5 V). Active Low 7.13.4 Function Assignment Each configurable Discrete Input can be configured in software to assign the inputs function. Once a function (except None and Generic Discrete) is selected for any given input, it is no longer available for assignment to any of the other inputs. See Figure 7-11. The Mic On, End Call, and Chime Reset functions are used in conjunction with the Extension 1 audio interface and are discussed in 7.15.1.1 below. Discrete Input No. 1 (Din 1) is dedicated as a Weight on Wheels (WOW1) input. Only Discrete Inputs Din 2 through Din 15 are software-configurable. None When an input is not connected to an active system (e.g. no connection, or wiring provisions only are installed), the input should be configured as None. Generic Discrete The Generic Discrete function allows customizable software components in the AFIRS to access raw discrete input data from systems whose input functions are not predefined. Connection and use of generic discrete input interfaces should only be done in conjunction with FLYHT engineering support. Cabin Lock When Cabin Lock is selected, cabin voice extensions are prevented from initiating a voice call, and if any voice call is in progress on a cabin extension, it is terminated. This input is only needed if there are cabin extensions being installed (Extensions 2 and/or 3) and the system integrator wants to provide the flight crew with the means to disable them. The Cabin Lock discrete will toggle the cabin lock function between the inactive and active states only when the discrete input transitions from the inactive state to the active state, e.g. this would be accomplished by a momentary switch used to turn the Cabin Lock function on and off on subsequent button presses. At system power up in this mode, the input resets to the inactive state (Cabin Active). 250-0019 Rev. --

22 April 2013 Confidential and Proprietary to FLYHT Aerospace Solutions Ltd. Page 47 AFIRS 228 Series Installation Manual Note:

Cabin Lock functionality is also provided on the MCDU interface. A Cabin Lock discrete input is only required if the system integrator wants to provide Cabin Lock functionality and there is no MCDU, or if the system integrator wants to use a discrete input instead of the MCDU interface. Event When the Event input transitions to the active state (momentary switch), it provides an indication to the AFIRS system that a noteworthy event has been identified by the flight crew. The AFIRS system can use the Event input to perform custom pre-defined functions, so its use needs to be coordinated with FLYHT engineering support. Iridium Off The functionality of this discrete input can be configured by the operator to be either All Off or Data Off. When configured for All Off and the Iridium Off input goes active, all voice and data transmissions over the Iridium modems are inhibited (all Iridium voice and data services are turned off and the AFIRS does not emit any RF energy). When configured for Data Off and the Iridium Off input goes active, only data transmissions over the Iridium modems are inhibited

(Iridium voice services and data receipt functions remain operational). When Iridium Off is deselected, normal Iridium functions will occur. The Iridium Off discrete will toggle the Iridium Off function between the inactive and active states only when the discrete input transitions from the inactive state to the active state, e.g. this would be accomplished by a momentary switch used to turn the Iridium Off function on and off on subsequent button presses. At system power up in this mode, the input resets to the inactive state (Iridium On). Note:

Iridium Off functionality is also provided on the MCDU interface. Iridium Off discrete input is only required if the system integrator wants to provide Iridium Off functionality and there is no MCDU, or if the system integrator wants to use a discrete input instead of the MCDU interface. Park Brake A Park Brake input should be provided to the AFIRS whenever possible, either from one of the digital databuses or using a discrete input. For the discrete input, when the Park Brake input transitions to the active state, the AFIRS is signaled that the aircrafts park brake is set, and the inactive state indicates that the aircrafts park brake is released (not set). System Reset When the System Reset input transitions to the active state (momentary switch), it commands the system to perform a reset. This function is not commonly used in aircraft installations, but it is available if needed. Page 48 Confidential and Proprietary to FLYHT Aerospace Solutions Ltd. 250-0019 Rev. --

22 April 2013 AFIRS 228 Series Installation Manual Weight on Wheels (WOW2) A second Weight-On-Wheels input may optionally be provided to the AFIRS system. Refer to 7.13.1 for the logic used when a WOW2 input is provided. Figure 7-11 Discrete Input and Output Interfaces 7.14 Discrete Outputs The AFIRS has 8 configurable Discrete Outputs, each of which is software-configurable for Active High or Active Low logic and the assigned function. The Discrete Outputs use Open-

Closed signal levels, where the output is either high-impedance to ground (Open) or low-

impedance to ground (Closed). Once a function (except None) is selected for any given output, it is no longer available for assignment to any of the other outputs. 250-0019 Rev. --

22 April 2013 Confidential and Proprietary to FLYHT Aerospace Solutions Ltd. Page 49 AFIRS 228 Series Installation Manual 7.14.1 Logic Configuration Each Discrete Output is software-configurable for Active Low or Active High signaling levels. When configured as Active Low and the assigned function goes active, the output will be in the Low State (<1.25V to ground). When the assigned function goes inactive, the output will be in the High State (Open Circuit). When configured as Active High and the assigned function goes active, the output will be in the High State (Open Circuit). When the assigned function goes inactive, the output will be in the Low State (<1.25V to ground). 7.14.2 Function Assignment Each Discrete Output can be configured in software to assign the outputs function. Once a function (except None) is selected for any given output, it is no longer available for assignment to any of the other outputs. The Call Light function is used in conjunction with the Extension 1 audio interface and is discussed in 7.15.1.1 below. The Ext 2 Call and Ext 3 Call functions are used in conjunction with the Extension 2 and 3 audio interfaces and are discussed in 7.15.3 below. None When an output is not connected to an active system (e.g. no connection, or wiring provisions only are installed), the output should be configured as None. Cabin Lock The Cabin Lock output reports the state of the Cabin Lock function. This output can be used to illuminate an annunciator when the Cabin Lock function is active. GPS Link The GPS Link output reports the loss of valid data from all of the systems Date-Time-Position

(DTP) sources. This includes the external DTP sources (e.g. FMSs) as well as the internal GPS satellite link. This output can be used to illuminate an annunciator whenever there are no DTP sources available. Note that this output may be active whenever the AFIRS antenna does not have a clear view of the sky and the external DTP sources are not able to provide valid DTP information (e.g. the aircraft is in a hangar). Iridium Off The Iridium Off output reports the state of the Iridium Off function. This output can be used to illuminate an annunciator when the Iridium Off function is active. ISVM Link The ISVM Link output reports the status of the internal Iridium voice modem satellite link. This output can be used to illuminate an annunciator whenever the ISVM cannot receive satellite signals. Note that this output will be active whenever the AFIRS antenna does not have a clear view of the sky (e.g. the aircraft is in a hangar). Page 50 Confidential and Proprietary to FLYHT Aerospace Solutions Ltd. 250-0019 Rev. --

22 April 2013 AFIRS 228 Series Installation Manual ISDM Link The ISDM Link applies only to the AFIRS 228S. This output reports the status of the internal Iridium safety-service data satellite link. This output can be used to illuminate an annunciator whenever the ISDM cannot receive satellite signals. Note that this output will be active whenever the AFIRS antenna does not have a clear view of the sky (e.g. the aircraft is in a hangar). Text Msg The Text Msg output indicates that the AFIRS text messaging service has received a new message. This output can be used to illuminate an annunciator when a new text message is received. 7.15 Satcom This section describes the interface and integration requirements for the AFIRS 228 Series system with a Satcom system. 7.15.1 Audio Integrating System Extension 1 is generally intended to be connected to the aircrafts audio integrating system for flight crew use. The interfaces required to fully support this functionality vary significantly depending on the design of the audio integrating system. Generally, the MCDUs are used for control and display of the Satcom functions for Extension 1. 7.15.1.1 Audio Discrete Signals There are 3 discrete inputs and 2 discrete outputs that can be used to support the integrated audio interface. Mic On Input The Mic On function can be configured for either Switched PTT (momentary switch) or Latched ACP (alternate action switch) mode. When the Mic On input is configured for Switched PTT, Voice Extension 1 (Mic/Phone input) will answer an incoming call when the Mic On input transitions to the active state. Once a call is in progress, the microphone audio channel will function as long as the Mic On input is in the active state. If a call is in progress and the Mic On input toggles to the inactive state, the microphone audio input will be muted. In this mode, the Mic On input does not terminate a call in progress. When the Mic On input is configured for Latched ACP, Voice Extension 1 (Mic/Phone input) will answer an incoming call when the Mic On input transitions to the active state. Once a call is in progress, the microphone audio channel will function as long as the Mic On input is in the active state. If a call is in progress and the Mic On input toggles to the inactive state, the call will be terminated. 250-0019 Rev. --

22 April 2013 Confidential and Proprietary to FLYHT Aerospace Solutions Ltd. Page 51 AFIRS 228 Series Installation Manual For outgoing calls when the Mic On input is configured for Latched ACP, the function is dependent on which control source is configured for Extension 1. When an MCDU is the Extension 1 dialing control, setting the Mic On input to the active state will initiate the dialing process using the phone number preselected on the MCDU. When a DTMF Dial Pad is the Extension 1 dialing control, setting the Mic On input to the active state indicates an off-hook event so that DTMF dialing can begin. End Call Input When a call is in progress and the End Call input transitions to the active state (momentary switch), Voice Extension 1 (Mic/Phone input) will terminate the call in progress. This input is often used to terminate a call when the Mic On input is configured for Switched PTT mode. Additionally, the End Call input can be used to reject an incoming call, regardless of whether the Mic On input is configured for Switched PTT or Latched ACP. Call Light Output The Call Light output is software configurable for either steady or flashing lights. When an incoming voice call is ringing, the Call Light output will transition to the active state; either in a steady state or flashing at approximately a 1 Hz rate. When the incoming call is subsequently answered, the Call Light output will remain active in the steady state as long as the call is in progress. When the call in progress is terminated, the Call Light output will go inactive. Chime Output The Chime output is software configurable for either single-stroke or multi-stroke. When an incoming voice call starts ringing, the Chime output will transition to the active state and then the inactive state; either once (single-stroke) or on and off until the call is answered or the Chime Reset input goes active (multi-stroke). The time that the Chime output is active and inactive is configurable in the ICT. The default settings of 500 ms on and 500 ms off provide an ARINC 741/761 compliant output. However, if a chime device such as a Sonalert is being used, the default times are too short. A chime active setting of 2.5 to 3.0 seconds and a corresponding inactive setting that produces the desired repetition rate may be more suitable, depending on the characteristics of the actual device being used. Chime Reset Input When an Iridium voice call is ringing and the Chime Reset input transitions to the active state

(momentary switch), the Chime output will be reset (i.e. transition to the inactive state) for the remainder of the time that the incoming call is ringing. This input is typically only required if the Chime output is used and it is configured for multi-stroke chime. Note:

When Chime Reset is applied, the chime is silenced but the function of the Call Light output is unaffected. 7.15.1.2 Switched PTT Configuration If the Audio Integrating System provides a momentary Push-To-Talk (PTT) output, the following interface can be used. When an incoming call is ringing and the PTT is keyed, the call will be answered. Once the call is established, the PTT must be keyed for the microphone audio to be Page 52 Confidential and Proprietary to FLYHT Aerospace Solutions Ltd. 250-0019 Rev. --

22 April 2013 AFIRS 228 Series Installation Manual transmitted. The End Call switch is used to end the call. Calls can also be answered and terminated on the MCDU screen, if available. The Call Light, Chime and Chime Reset interfaces can be used to provide visual and aural annunciations in the cockpit. The system integrator should design the visual and aural call indications to be consistent with the aircrafts cockpit design philosophy. See Figure 7-12. Figure 7-12 Switched PTT Audio Interface 7.15.1.3 Latched ACP Configuration If the Audio Integrating System provides a latched Mic On output, the following interface can be used. When an incoming call is ringing and the Satcom switch on the Audio Control Panel is pressed, the call will be answered and microphone audio will always be live. The Satcom switch on the Audio Control Panel is pressed a second time to end the call. Calls cannot be answered and terminated on the MCDU screen in this configuration. The following diagram also shows how the Call Light output can be interfaced to an Audio Integrating System that provides Satcom visual and aural call indications. In this case, a Call Light, Chime and Chime Reset switch are not required. See Figure 7-13. 250-0019 Rev. --

22 April 2013 Confidential and Proprietary to FLYHT Aerospace Solutions Ltd. Page 53 AFIRS 228 Series Installation Manual Figure 7-13 Latched ACP Audio Interface 7.15.2 DTMF Dialing Source If a compatible MCDU is not available in the aircraft, a 2-wire dial pad may be used to provide control and display of the Satcom functions for Extension 1. The following figure shows a typical dial pad installation. Refer to the applicable dial pad manufacturers installation instructions for proper wiring connections. The Call Light, Chime and Chime Reset interfaces are optional, and can be used to provide visual and aural annunciations in the cockpit. The system integrator should design the visual and aural call indications to be consistent with the aircrafts cockpit design philosophy. See Figure 7-14. Page 54 Confidential and Proprietary to FLYHT Aerospace Solutions Ltd. 250-0019 Rev. --

22 April 2013 AFIRS 228 Series Installation Manual Figure 7-14 Dial Pad Interface 7.15.3 Satcom Handsets The AFIRS 228 can connect with up to two handsets. Any aviation-quality handset with a 2-wire POTS interface (meeting the specifications of 4.1.10) may be used. The handsets are generally intended for cabin crew use. A handset is not recommended for use in the cockpit, as the integrated audio interface is preferred. The following diagram shows a typical cordless base station interfaced to Extension 2 and a regular handset to Extension 3, but either handset type may be used at either extension. Refer to the applicable handset manufacturers installation instructions for proper wiring connections. If Extension 3 is used as a DTMF dialing source for the Extension 1 audio interface, then only Extension 2 is available for connection to a handset. 250-0019 Rev. --

22 April 2013 Confidential and Proprietary to FLYHT Aerospace Solutions Ltd. Page 55 AFIRS 228 Series Installation Manual Call Lights for Extensions 2 and 3 may be located near the respective handset to provide an additional visual indication that the extension is ringing. Their use is optional and at the system integrators discretion. Discrete outputs 4 and 5 are shown, but any of the configurable discrete outputs may be used. See Figure 7-15. Ext 2 Call The Ext 2 Call output can be configured for either steady or flashing lights. When a voice call on Extension 2 is ringing, the Ext 2 Call output will transition to the active state; either in a steady state or flashing at a 1 Hz rate. When the incoming call is subsequently answered, the Ext 2 Call output will remain active in the steady state as long as the call is in progress on Extension 2. When the call in progress is terminated, the Ext 2 Call output will go inactive. Ext 3 Call The Ext 3 Call output can be configured for either steady or flashing lights. When a voice call on Extension 3 is ringing, the Ext 3 Call output will transition to the active state; either in a steady state or flashing at a 1 Hz rate. When the incoming call is subsequently answered, the Ext 3 Call output will remain active in the steady state as long as the call is in progress on Extension 3. When the call in progress is terminated, the Ext 3 Call output will go inactive. 2 20 AWG 20 AWG J1B (MP) 15G 15H Tip Ring Ext. 2 Ext 2 Call (Dout 4)

(500 mA Max.) 8G Ext. 3 Tip Ring 15J 15K 2 20 AWG 20 AWG Ext 3 Call (Dout 5)

(500 mA Max.) 11G DMU Figure 7-15 Handset Interface 28 VDC Power In Power Ground Tip Ring Shield Cordless Base Station Annunciator Power 28 VDC Power In Tip Ring Power Ground Jetphone Handset Annunciator Power P1 1 2 P2 1 3 2 CALL

(Opt.) P1 9 1 3 7 CALL

(Opt.) Page 56 Confidential and Proprietary to FLYHT Aerospace Solutions Ltd. 250-0019 Rev. --

22 April 2013 AFIRS 228 Series Installation Manual 8. SYSTEM CONFIGURATION You configure the AFIRS system via the Maintenance Port using a laptop, web browser, and the AFIRS 228 Series maintenance program which has a graphical user interface (GUI). IMPORTANT: This manual provides information on how to connect to the Maintenance Port and access the AFIRS maintenance program. It also provides general information on the steps required to configure and update the AFIRS system. Detailed information on how to operate the maintenance program and troubleshoot the operation of the AFIRS system is provided in the AFIRS 228 Series, Automated Flight Information Reporting Systems Operators Manual, document number 250-0022. The AFIRS 228 Series has an Ethernet interface for the Maintenance Port connection. An RJ-45 Maintenance Port jack is located behind the access door on the front panel of the DMU as shown in Figure 8-1. Figure 8-1 Maintenance Port Location Note:

When performing the initial configuration of an installed system, perform and complete the Before Power-On Tests in section 9.1 before applying power to the AFIRS system. 250-0019 Rev. --

22 April 2013 Confidential and Proprietary to FLYHT Aerospace Solutions Ltd. Page 57 AFIRS 228 Series Installation Manual 8.1 Connecting to the Maintenance Port You access the AFIRS 228 Maintenance Program by connecting an Ethernet cable to the Maintenance Port of the AFIRS 228 unit. Alternatively, as described in section 7.12, one of the rear connector Ethernet ports can be used to provide an additional Maintenance Port connection in the aircraft (e.g. in the cockpit) so that system maintenance activities can be performed in a location remote from the AFIRS 228 Data Management Unit (DMU). Also, if an Electronic Flight Bag (EFB) with a supported web browser installed is connected to one of the rear Ethernet port connections, the EFB can be used as an AFIRS maintenance terminal and a laptop is not required. To connect to the Maintenance Port and access the Maintenance Program:

1. On the AFIRS 228 unit, open the front panel access door. 2. Connect an Ethernet cable to the Maintenance Port. AFIRS 228 system power may be on or off. 3. Connect the other end of the Ethernet cable to a laptop that is running a web browser. Note:

The laptop network adapter must be set to DHCP to access the IP address. FLYHT has tested Internet Explorer 8, Firefox 7 and 9, and Google Chrome 16 (or later versions) with the AFIRS 228. 4. If not already powered, apply power to the AFIRS DMU. 5. Confirm that the green link light (adjacent to Maintenance Port RJ45 connector) is illuminated, either steady or flashing (a flashing link light indicates that data is being transmitted). 6. Open a web browser on the laptop and in the Address bar type the following IP address:

192.168.128.1 The AFIRS 228 Home page appears with the General tab information displayed. Figure 8-2 Home Page General Tab Page 58 Confidential and Proprietary to FLYHT Aerospace Solutions Ltd. 250-0019 Rev. --

22 April 2013 AFIRS 228 Series Installation Manual The Home page (see Figure 8-2) displays three main areas of information:

1 Login area 2 Menu of available links to pages accessible in current login mode of operation 3 Status tabs: General, ARINC, and Discrete In Upon login, the default view opens to the General tab (see Figure 8-2) which displays the following information:

4 System status data display area 5 System information data display area 6 Link test (user activated) used to test the connection to the Uptime Server For information on the other two Home page tabs (ARINC and Discrete In) see section 8.1.1. 8.1.1 Home Page Tab Descriptions The General tab page displays:

UTC Date and Time: This is correlated to a GPS clock if you have a fixed GPS link. If no link is available a default date will be displayed. Position: This is the AFIRS GPS position. If no GPS is fixed, No GPS will be displayed. ICAO Address: This field displays the aircrafts ICAO address. The address is configured at system setup by the installer (must be in Maintenance Installer mode). ISVM IMEI: Iridium Satellite Voice Modem International Mobile Equipment Identity. ISDM IMEI: Iridium Satellite Data Modem: Not available in this release. Phone Number: Displays the aircraft phone number. Link Test: This is an active selection which is used to verify a link between a registered AFIRS 228 unit and the FLYHT Uptime Server. When Link Test is selected a packet of information transmitted to the FLYHT Uptime Server. If the information is received the Uptime Server will reply with an acknowledgement. Successful communication is confirmed by a RECEIVED message, unsuccessful communication is confirmed by a TIME OUT message. AFIRS 228 Status Indicators:

System: Yellow (INIT) initializing, Green (OK), Yellow (FAULT), Red indicates Aircraft Configuration Module (ACM) or Data Management Unit (DMU) Hardware failure - critical ISVM LINK: Yellow (NO FIX) no iridium link, Green (OK) ISDM LINK: N/A, future functionality GPS LINK: Yellow (NO FIX), Green (OK) The ARINC tab displays the state of the 16 ARINC 429 RX channels and the 1 ARINC 717 RX channel. The status of a configured function is either ACTIVE or FAULT. 250-0019 Rev. --

22 April 2013 Confidential and Proprietary to FLYHT Aerospace Solutions Ltd. Page 59 AFIRS 228 Series Installation Manual The DISCRETE IN tab displays the state of the 16 discrete inputs. The state of the configured functional input is either ACTIVE or INACTIVE. 8.1.2 Faults Page The Faults page provides access to the AFIRS system fault log and history. 8.1.3 Part Numbers Page The Part Numbers page provides the status of the software and hardware configuration of the AFIRS system. 8.2 Accessing Maintenance Mode To make changes to the configuration tables, you need to access the Maintenance Mode function of the AFIRS maintenance program. Current versions of the maintenance program do not require a user name and password for access to Maintenance Mode. This functionality may be available in later versions of the software. Before accessing Maintenance Mode, you need to be connected to the AFIRS Maintenance Port and have the Maintenance Program open. To access and login to Maintenance Mode:

1. Once connected to the AFIRS 228 Maintenance Port and Maintenance Program GUI, from the Home page, click Login. You do not need a Username and Password. The AFIRS 228 Home page appears and the status fields will reflect your current system health. The AFIRS 228 Home page now indicates that you are logged in as an Installer, which provides you with the capability to enter Maintenance Mode. 2. To enter Maintenance Mode, on the top right corner of the screen, click Enter Maintenance Mode. A confirmation prompt message appears (see Figure 8-3) reminding you that if you enter Maintenance Mode key AFIRS services will be turned off. You will need to reboot the system

(full system reset) to turn the services back on and return to normal Operational Mode. Figure 8-3 Entering Maintenance Mode Message 3. To enter Maintenance Mode, select OK. Page 60 Confidential and Proprietary to FLYHT Aerospace Solutions Ltd. 250-0019 Rev. --

22 April 2013 AFIRS 228 Series Installation Manual The Home screen appears as shown in Figure 8-4. The SYSTEM status indicates that the system is in fault and appears illuminated in yellow. This SYSTEM fault status is indicated as the AFIRS system turns off when you are in Maintenance Mode. When you exit Maintenance Mode, and the system restarts, the SYSTEM status will appear green. Figure 8-4 Maintenance Mode Initial Display Screen In Maintenance Mode, the Home page provides the following additional left-hand menu items:

Address Book, ORT, ICT, Discrete, SLIC Calibration, and Upgrades. The following sections describe the functionality of the additional menu items available in Maintenance Mode. Detailed information on how to use the Maintenance Mode program are provided in the AFIRS 228 Series Operators Manual, document number 250-0022. 8.2.1 Maintenance Mode Menu Descriptions The links available from the left-hand menu enable the Maintenance Installer to check, test, verify, and configure the AFIRS system as follows:

Click Address Book to add, delete, or edit contact information, set call priorities and extension dialing, and enable/disable protection. Click ORT (Owner Requirements Table) to configure customized settings for specific aircraft and or operator requirements. Refer to the Appendix for a worksheet to help you define your requirements before editing the ORT information. Click ICT (Installation Configuration Table) to define how the AFIRS system interfaces to the aircraft. Refer to the Appendix for a worksheet to help you define your system requirements before editing the ICT information. Click Discrete to display the configuration of the Discrete Outs for testing purposes. You can verify the function of systems interfaced to the various discrete outputs by toggling the state from ACTIVE to INACTIVE and verify the expected response. 250-0019 Rev. --

22 April 2013 Confidential and Proprietary to FLYHT Aerospace Solutions Ltd. Page 61 AFIRS 228 Series Installation Manual Click SLIC Calibration to calibrate the interface for phone extensions 2 and 3. You need to calibrate the SLIC interface at time of installation and system configuration to improve noise immunity on the twisted pairs connected to additional handsets (if they are installed and operational). Click Upgrades to upgrade and update the software of the AFIRS 228 system. 8.3 Configuring the AFIRS 228 System This section provides basic information on how to configure the AFIRS 228 system as a Maintenance Installer logged into the Maintenance Mode of the AFIRS maintenance program. Detailed information about how to operate and use the maintenance program accessed via the AFIRS 228 maintenance port is provided in the AFIRS 228 Operators Manual (document number 250-0022) which is available from FLYHTs product support department. The following sections are intended to provide you with information on the configuration process and data inputs required to install and verify a system as operational. Worksheets for the ORT and ICT data are provided in the Appendix of this manual and the AFIRS 228 Series Operators Manual. Aircraft specific information required to configure the system should be provided to the installer by the aircraft specific documentation and the Instructions for Continued Air-Worthiness. For the purposes of installation, system configuration and verification, the following steps should be completed:

1. Configure the Address Book and set call priorities. 2. Configure the ORT data. 3. Define the ICT for aircraft and system interface requirements. 4. Calibrate SLIC for extensions 2 and 3 (if installed). 8.3.1 Configuring the Address Book The Address Book can only be edited if you are logged into Maintenance Mode. If you are in Operational Mode, you can view the Address Book content, but not edit the information or change the settings. The address book entries can also be viewed by a MCDU; however, you can only edit the information or change settings from within the AFIRs Maintenance Program. To access the Address Book:

1. From the left-hand menu, click Address Book. The Address Book screen appears (see Figure 8-5). Page 62 Confidential and Proprietary to FLYHT Aerospace Solutions Ltd. 250-0019 Rev. --

22 April 2013 AFIRS 228 Series Installation Manual Figure 8-5 Address Book Screen 2. Add contact information or edit information as required after reviewing the configuration tips provided below. Important tips for configuring the Address Book:

Order#: If you are not using an MCDU, but are using a dialer pad, you can use the Order

# for speed dialing of the address entries. Phone Number: Enter the phone number for each contact. Contact Name: Use uppercase letters in the Contact Name text field. Lower case letters will not be accepted by the system as a valid entry. Default Call Priority: You can set the Default Call Priority to match the terminology of either Airbus or Boeing categories. Airbus options are Emergency, Safety, Non-Safety, and Public. Boeing options are Emergency, Operational High, Operational Low, and Public. Protected: Under Protected if you select YES, you protect the Address Book entry so that it cannot be edited from the MCDU. If you select NO, the Address Book entry will be unprotected and therefore editable from the MCDU. Extension 2 and 3 Speed Dial: Used to configure speed dialing to extensions on the aircraft. When using a MCDU, you will have access to Extension 2 and 3. When using an AFIRS Keypad, you will only have access to one extension: Extension 2. 8.3.2 Configuring the Owner Requirements Table The Owner Requirements Table (ORT), shown in Figure 8-6 contains the configuration items that may be customized by the individual aircraft operator. These settings may be changed as required to meet operational requirements or preferences. 250-0019 Rev. --

22 April 2013 Confidential and Proprietary to FLYHT Aerospace Solutions Ltd. Page 63 AFIRS 228 Series Installation Manual Figure 8-6 ORT Screen Page 64 Confidential and Proprietary to FLYHT Aerospace Solutions Ltd. 250-0019 Rev. --

22 April 2013 AFIRS 228 Series Installation Manual Note:

An ORT Configuration Worksheet is provided in Appendix B to assist the operator in selecting and documenting the correct ORT configuration settings. To access and edit the ORT:

1. Click the ORT link on the left-hand side of the screen. The ORT page appears. 2. Enter the AIRCRAFT INFO: REGISTRATION or FLEET IDENTIFICATION NUMBER (FIN). The content of this field is typically used in AFIRS reports that are sent off the aircraft. This entry is a free text field that can be up to 24 characters long. The character set for this field is limited to those characters that can be entered and displayed on an MCDU, which are the uppercase alpha-numeric characters plus five special characters: [Space] + - . /

3. Enter the aircrafts 24-bit ICAO address. The content of this field is typically used in AFIRS reports that are sent off the aircraft. The address can be entered and displayed in hexadecimal, octal, or binary format. Note:

If the aircraft installation includes an interface to a system that provides the ICAO address to the AFIRS, this parameter may be automatically updated to the value supplied by the external system. 4. Set the FDM data size reserve space. Space is reserved for FDM data on the CompactFlash card so that other data does not overwrite the FDM data before the operator has had the opportunity to download the FDM data. The default setting is 1.0 GB, but this can be set between 0.1 GB and 4.0 GB as required. 5. Set the POWER MANAGEMENT option. When the AFIRS has power sources connected to both the Main and Alternate power inputs, the SHUTDOWN DELAY TIME sets how long the system will continue to operate on the Alternate power source once the Main power source has been removed. The default is ALWAYS ON. 6. Configure the MCDU options:

a) SYSTEM NAME: Enter the preferred MCDU display name for the AFIRS system. The system name that is displayed on the MCDU can be selected from the list shown in Appendix A. The default is AFIRS. b) CALL PRIORITY NAME 1 4: Select the label used to identify the four call priorities. The label options can be selected from the sets shown in Appendix A. The default is EMERGENCY, SAFETY, NON-SAFETY, and PUBLIC. c) ALLOW IRIDIUM OFF: The AFIRS system can be configured to provide an ALLOW IRIDIUM OFF selection on the MCDU. The default is NO; if set to NO, Iridium activity will not display on the MCDU. If you select YES, the IRIDIUM activity does appear on the MCDU. This setting affects only the MCDU functionality. If the system is configured to 250-0019 Rev. --

22 April 2013 Confidential and Proprietary to FLYHT Aerospace Solutions Ltd. Page 65 AFIRS 228 Series Installation Manual provide an ALLOW IRIDIUM OFF discrete input, the function of that discrete input is unaffected by this configuration setting. 7. Select the IRIDIUM data reporting options. When the AFIRS system is in the IRIDIUM OFF MODE, the system can be configured to either disable only data reporting to the MCDU, or to disable all Iridium satellite voice and data transmissions. The default is ALL OFF. 8. Set the options for AIR TO GROUND CALLS. a) CHIME ON CONNECT: The AFIRS system can be configured to trigger the chime output when an Air-to-Ground call connects. The default is NO. b) CIP TRANSITION: The AFIRS system can be configured to communicate (and display) the Call in Progress (CIP) transition state to the MCDU either when an Air-to-Ground call is initiated, or when it is connected. The default is CONNECTED. c) CALL PROGRESS TONES: The AFIRS system can be configured to use either CALL PROGRESS TONES that are North American or European. The default is NORTH AMERICAN. 9. Configure the DEFAULT CALL PRIORITY. The default call priority can be configured for Extension 1. The default setting is 2. Priority 1 is reserved for emergencies. The default call priority can be configured for Extensions 2 and 3. The default setting is 3. Note:

The call priority for any individual call dialed from an MCDU can be changed at the time of placing the call. The call priority for any outgoing calls dialed using a Dual Tone Multiple Frequencies (DTMF) dial pad will be set to the priority configured in the ORT. The call priority for any outgoing calls dialed from Extension 2 or 3 is set to the priority configured in the ORT. Extensions 2 and 3 should not be set to priority 1 unless they will only ever be used to place an Emergency call. Placing an Emergency call can trigger ATC alarms and emergency responses, so extreme caution should be exercised whenever an extension is configured to allow making an Emergency call. 10. Configure the DIRECTORY COUNT. The speed dial entries for Extension 1 are grouped into directories. The AFIRS system can be configured to provide between 1 to 10 different directories. The default setting is 4. 11. Name DIRECTORY 1, 2, 3, 4, 5, 6, 7, 8, 9 & 10. The name of each directory is configurable. The DIRECTORY NAME is a free text field that can be up to 10 characters long. The character set for this field is limited to those characters that can be entered and displayed on an MCDU, which are the uppercase alpha-numeric characters plus five special characters; [Space] + - . /

Page 66 Confidential and Proprietary to FLYHT Aerospace Solutions Ltd. 250-0019 Rev. --

22 April 2013 AFIRS 228 Series Installation Manual Note:

The default settings provide four directories named EMERGENCY, SAFETY, NON-SAFETY, and PUBLIC. Only the Directory Names for the number of directories set in the DIRECTORY COUNT field are used by the system. 12. Configure ALLOW MANUAL DIALING. Each extension can be configured to ALLOW MANUAL DIALING, or to permit the user to only select a number for the directories or speed dial lists. The default setting is YES for each extension. IMPORTANT! To obtain operational approval for safety-services voice in accordance with FAA AC20-150A, Extension 1 must be configured YES to allow manual dialing for the flight crew. 13. Configure GROUND TO AIR CALLS. You can configure the system to ALLOW LOW PRIORITY CALLS IN COCKPIT (Priority 4) to ring. The default setting is YES. You can configure the RING TYPE for incoming calls can be configured to either ring all three extensions concurrently, or to ring one extension at a time (sequencing through the extensions). The default setting is SEQUENTIAL. 14. Configure the SEQUENTIAL RING order. RING ORDER: You can configure the sequential ring order to be Extension 1 first, then extension 2, and then extension 3 (which is the default) or you may configure the ring sequence in any order. RING COUNT: Each extension can be configured as to how many times it will ring when it is the active extension in the ring sequence. The default is 5 for each extension. Using the default settings, an incoming call will ring (until answered) for 5 times on Extension 1, then 5 times on Extension 2, and then 5 times on Extension 3. If unanswered by this time, the system will terminate the incoming call. 15. Set the CONCURRENT RING amount. If the Ring Type is set to CONCURRENT RING, the number of times the extensions will ring before the system terminates the incoming call can be configured. The default is 5. 16. Configure the ring options for Extension 1, 2, and 3 RING. Each extension can be configured as to whether or not it will RING on an incoming call. The default is YES for all extensions. If an extensions location is configured as NONE, the extension will not ring regardless of this setting. 17. Configure the CALL LIGHT and CHIME (cockpit/extension 1 only). The behavior of the CALL LIGHT and CHIME discrete outputs can be configured. The default setting is STEADY/SINGLE-STROKE. 250-0019 Rev. --

22 April 2013 Confidential and Proprietary to FLYHT Aerospace Solutions Ltd. Page 67 AFIRS 228 Series Installation Manual a. FLASHING/MULTI-STROKE: When there is an incoming call, both the Call Light output and the Chime output will toggle between active and inactive states. b. FLASHING/SINGLE STROKE: When there is an incoming call, the Call Light output will toggle between active and inactive states. The Chime output will transition only once to the active state. c. STEADY/SINGLE STROKE: When there is an incoming call, the Call Light output will toggle to the active state and remain there. The Chime output will transition only once to the active state. For an incoming call, the system can be configured to output a RING TONE on the audio output of Extension 1 (Cockpit). The default setting is YES. When Extension 2 (cabin) or Extension 3 (cabin) is placed on hold and the call remains active, the system will re-ring that extension to remind the operator that a call is still holding. You can set the RE-RING TIME from 1 to 10 minutes. The default setting is 5. When re-ringing Extension 2 or Extension 3, the system will ring that extension a number of times before terminating the call; you can set the number of rings from 1 to 10. The default setting for the field RE-RING COUNT is 5. For an incoming call, you can define the behavior of the CALL LIGHT for the Extension 2 and Extension 3 to be either STEADY or FLASHING. The default is STEADY. 18. Select a service provide for SAFETY SERVICE. Choose the service provider ARINC or SITA. 8.3.3 Configuring the Installation Configuration Table The Installation Configuration Table (ICT) (see Figure 8-7) contains the configuration items that define how the AFIRS system interfaces to the aircraft. When in Maintenance Installer Mode, you can update the installation configuration data as required for your specific installation requirements. Figure 8-7 Installation Configuration Table Screen An ICT Configuration Worksheet is provided in Appendix A to assist the installer in selecting and documenting the correct ICT configuration settings. Page 68 Confidential and Proprietary to FLYHT Aerospace Solutions Ltd. 250-0019 Rev. --

22 April 2013 AFIRS 228 Series Installation Manual 8.3.4 Calibrating SLIC The SLIC calibration page (see Figure 8-8) is used to set longitudinal balance. The measurement is made at installation time to improve noise immunity on the twisted pairs connected to the handsets (extensions 2 and 3). Figure 8-8 SLIC Calibration Screen 8.4 Upgrading AFIRS 228 Software The AFIRS 228 system software is field-upgradeable using the Upgrade function of the Maintenance Port program. You can access the software upgrade functionality when logged into the AFIRS maintenance program in Maintenance Mode, by clicking the Upgrades link available on the left-hand menu of the AFIRS maintenance program screen. 8.4.1 Upgrade Materials Make sure you have the following materials available before beginning the upgrade procedure. A notebook computer with an Ethernet port, running the Microsoft Windows operating system and a web browser such as Internet Explorer. NOTE: The Ethernet port (TCP/IPv4) must be configured to obtain an IP address automatically. Instructions for Continued Airworthiness applicable to the AFIRS Installation. A standard, straight through Ethernet patch cable. A copy of the software upgrade file (upgrade.tgz) applicable to the software release. A copy of the software release notes to identify any changes to functionality or special upload instructions. A P-Touch, Label Maker or equivalent with black type on silver/white background labels. 8.4.2 Upgrade Procedure Before beginning the upload procedure, make sure you have saved the applicable software file

(.tgz) to an accessible location on your laptop. Make sure you review the software release notes 250-0019 Rev. --

22 April 2013 Confidential and Proprietary to FLYHT Aerospace Solutions Ltd. Page 69 AFIRS 228 Series Installation Manual and air worthiness instructions for the specific software upgrade you are planning on installing. Special instructions, specific to each install, are provided in the software release notes. To upgrade the AFIRS 228 software:

1. From the left-hand menu, click Upgrades. The Upgrades screen appears. 2. Click Browseto locate the software file you want to upload to the system. 3. Once you have selected the software file you want to upload, click Upload to start the upgrade process. A progress bar appears indicating the file uploading status and lists the image files that are loading into volatile memory. When the upload is complete the progress bar changes color from blue to green (see Figure 8-9). Figure 8-9 Upgrade Progress IMPORTANT! If you upload the incorrect file, but have not yet clicked Apply, click Reset to clear uploaded software. Reset clears the volatile memory of the software. If you have already applied the software, you will have to repeat the upgrade to upload and apply the correct software files. 4. To load the software into non-volatile memory and complete the software upgrade procedure, click Apply. A progress bar appears indicating that the software file is being installed into the non-

volatile memory of the AFIRS 228 unit. When the progress bar appears green, the software upgrade has been applied to the unit (see Figure 8-10). Page 70 Confidential and Proprietary to FLYHT Aerospace Solutions Ltd. 250-0019 Rev. --

22 April 2013 AFIRS 228 Series Installation Manual Figure 8-10 Software Loading Progress Screens IMPORTANT: To activate the new software load you need to exit Maintenance Mode and restart the AFIRS 228 unit. 5. To exit Maintenance mode, from the top-right corner of the screen, click Exit Maintenance Mode. A confirmation message appears that asks you to confirm that you want to exit Maintenance Mode (see Figure 8-11). Figure 8-11 Exit Message 6. Click OK. The AFIRS 228 unit automatically restarts and applies the newly installed software. A progress bar appears indicating the status of the reboot (restart) process. 250-0019 Rev. --

22 April 2013 Confidential and Proprietary to FLYHT Aerospace Solutions Ltd. Page 71 AFIRS 228 Series Installation Manual Figure 8-12 Exit Maintenance Mode Progress Bar 7. When the restart is complete, verify that the AFIRS unit is functioning as expected and verify that correct version of software has been loaded. To verify functionality and check the software version:

a. Log in to the AFIRS maintenance program. b. From the Home page, open the General and ARINC tabs to review the system status to confirm that no faults are displayed. c. From the left-hand menu, click ORT and review the ORT settings to confirm they are correct as per the Instructions for Continued Airworthiness (ICA). d. From the left-hand menu, click ICT and review the ICT settings to confirm they are correct as per the ICA. e. From the left-hand menu, click Part Numbers to verify that the part number displayed for each component matches the required software version and part number as noted in the release notes or upgrade instructions. Page 72 Confidential and Proprietary to FLYHT Aerospace Solutions Ltd. 250-0019 Rev. --

22 April 2013 AFIRS 228 Series Installation Manual 8.5 Exiting Maintenance Mode To save your changes and configuration data you need to exit maintenance mode. To exit maintenance mode:

1. In the top-right hand corner of the screen, click Exit Maintenance Mode. A Message appears notifying you of the number of changes that you have made and asks you for confirmation (see Figure 8-13). IMPORTANT! If you click Cancel, your changes are still active but not saved. Figure 8-13 Exiting Prompt Message 2. To save your changes, click OK. A confirmation message appears asking you to confirm that you want to save the changes that you made (see Figure 8-14). If you click Cancel, you exit maintenance mode and your changes are NOT saved (i.e. changes are deleted). Figure 8-14 Save Prompt 250-0019 Rev. --

22 April 2013 Confidential and Proprietary to FLYHT Aerospace Solutions Ltd. Page 73 AFIRS 228 Series Installation Manual 3. To save your changes and exit maintenance mode. Click OK. You exit maintenance mode and the AFIRS 228 restarts. If you try to access the maintenance interface during this restart, the following message and progress indicator appears. Figure 8-15 Exit and Restart Progress Screen 4. To verify your changes and confirm that you have installed the correct software, from the Maintenance Program Home page, open the tab Part Numbers. The Part Numbers screen appears as shown in Figure 8-16. You can check the software part number status by opening the SOFTWARE tab on the Part Numbers screen. Figure 8-16 Software Part Number Status Screen Page 74 Confidential and Proprietary to FLYHT Aerospace Solutions Ltd. 250-0019 Rev. --

22 April 2013 AFIRS 228 Series Installation Manual 9. MAINTENANCE AND CHECKOUT This section provides instructions on post-installation checkout procedures and information on Instructions for Continued Airworthiness. For detailed operating procedures and additional system troubleshooting information, refer to the AFIRS 228 Series Operators Manual, document number 250-0022. 9.1 Post-Installation Checkout 9.1.1 Before Power-On Tests 1. Before installing the AFIRS DMU in the mounting tray, confirm that all aircraft interface wiring is correct as per the aircraft wiring integration design. 2. Confirm that a valid SIM card is installed in the Aircraft Configuration Module (ACM). 3. Set the AFIRS circuit breaker for the Main power source and confirm that 28 VDC power is available between pins J1C-2 and J1C-3. Pull the circuit breaker and ensure that Main power is removed. 4. If an Alternate power source is connected, set the AFIRS circuit breaker for the Alternate power source and confirm that 28 VDC power is available between pins J1C-9 and J1C-3. Pull the circuit breaker and ensure that Alternate power is removed. 5. Place the AFIRS DMU in the mounting tray and secure the front hold-down. 6. Open the front panel door and confirm that a flash card is installed in the DMU. Note:

Only FLYHT P/N 502-1180-x flash cards should be used in the AFIRS system. These cards have been tested to ensure they function correctly in all expected operating environments. 9.1.2 Power-On Tests 1. The cockpit AFIRS FAULT indication should be illuminated when power is not applied to the AFIRS system. 2. Set the AFIRS circuit breaker for the Main power source. The SYSTEM STATUS indicator on the front panel of the DMU will illuminate amber indicating that the system is initializing. Note:

The first time a DMU is installed in an aircraft, the SYSTEM STATUS indicator will typically remain amber even after it has initialized. This indicates that the system is not fully operational, in this case because the proper configuration settings have not yet been made. 3. Configure the ICT and ORT in accordance with the procedures contained in section 8. Keep the laptop connected to the Maintenance Port after finishing the configuration procedure. 4. Once the system resets, the SYSTEM STATUS indicator on the front panel of the DMU will illuminate amber while the system is initializing; it will then turn green once the system is operational. The cockpit AFIRS FAULT annunciator should remain illuminated whenever the SYSTEM STATUS indicator is amber, and extinguish when the SYSTEM STATUS indicator turns green. 250-0019 Rev. --

22 April 2013 Confidential and Proprietary to FLYHT Aerospace Solutions Ltd. Page 75 AFIRS 228 Series Installation Manual Note:

If the SYSTEM STATUS indicator doesnt turn green after 60 seconds, the system is not fully operational. This may be because of an incorrect configuration setting, or one of the configured interfaces is not operational. 9.1.3 Aircraft Systems Interface Tests Note:

The tests listed in this section are generic in nature and are not intended to be used as a test plan for any specific aircraft installation. They should only be used by the aircraft systems integrator as a guide in developing the correct and complete aircraft-specific integration tests. The aircraft systems integrators test plan should ensure that the aircraft and its systems are in a safe condition for each test to be performed. 9.1.3.1 Alternate Power Test 1. Confirm 28 VDC power is available at both the Main and Alternate power inputs, and that the AFIRS system is initialized and operating. 2. Remove power from the Main input. Confirm AFIRS continues to operate. Note:

If AFIRS is configured to provide a shutdown delay, this step can be extended and timed to verify the AFIRS automatically shuts down at the correct delay time. 3. Remove power from the Alternate input to power down the unit. 4. Apply 28 VDC power to the Alternate power input only. If the Remote Start input pin (J1C-5) is jumpered to ground, confirm the system initializes properly. 5. If the Remote Start input pin (J1C-5) is connected to an aircraft system, manipulate that system to provide a ground on the Remote Start input. Confirm the AFIRS system initializes properly. 6. Restore 28 VDC power to the Main power input. 9.1.3.2 ARINC Databus Interface Tests 1. Using the maintenance terminal, display the AFIRS Home page. 2. Confirm the aircraft system connected to the databus port being tested is operational and transmitting on the databus. 3. Confirm that the following databuses are shown as operational, as applicable:

a. ARINC 717 Rx Bus b. ARINC 429 Rx Bus (1-16) 9.1.3.3 MCDU Tests If installed, confirm AFIRS functionality on each MCDU as follows:

1. On the MCDU Main Menu, AFIRS (or SATCOM) should be available at one of the Line Select Keys (LSKs). Press the AFIRS LSK and the AFIRS MAIN page should be displayed. Page 76 Confidential and Proprietary to FLYHT Aerospace Solutions Ltd. 250-0019 Rev. --

22 April 2013 AFIRS 228 Series Installation Manual 2. Press the <STATUS LSK. The AFIRS STATUS page should be displayed. 3. Press the <RETURN LSK. The AFIRS MAIN page should be displayed. 9.1.3.4 Serial Port Tests If installed, confirm AFIRS connectivity to each serial port device as follows:

1. Perform any tests specific to the connected system to confirm that it is communicating with the AFIRS over the serial port. 9.1.3.5 Ethernet Tests If installed, confirm AFIRS connectivity to each Ethernet device as follows:

1. Confirm the DMU front panel ETHERNET indicator for the connected port is green. Flashing green indicates data is being transferred. 2. Perform any tests specific to the connected system to confirm that it is communicating with the AFIRS over the Ethernet port. 9.1.3.6 Discrete Input Tests For each discrete input connected, confirm the correct state is detected as follows:

1. Monitor the Discrete Inputs on the maintenance terminal Home page. Manipulate the system providing the discrete input as required to output the inactive state. Confirm proper display on the Home page. 2. Manipulate the system providing the discrete input as required to output the active state. Confirm proper display on the Home page. 9.1.3.7 Discrete Output Tests For each discrete output connected, confirm the correct aircraft system interface as follows:

1. Using the maintenance terminal, place the AFIRS system in the Maintenance Mode. Click on the Discrete Output link on the left hand side of the screen. 2. Select the discrete output to its inactive state. Confirm proper operation of the interfaced aircraft system. 3. Select the discrete output to its active state. Confirm proper operation of the interfaced aircraft system. 4. Exit Maintenance Mode and allow the AFIRS system to restart. 9.1.4 Operational System Tests Note:

The tests in this section require the aircraft to be powered and outside the hangar in a location that has a clear view of the Iridium and GPS satellites. Aircraft systems that interface with the AFIRS must be installed and operational. These tests also require the AFIRS system to have been activated on the Iridium network by FLYHT, and for a valid SIM card to be installed in the ACM. 250-0019 Rev. --

22 April 2013 Confidential and Proprietary to FLYHT Aerospace Solutions Ltd. Page 77 AFIRS 228 Series Installation Manual 9.1.4.1 Date, Time, and Position Tests 1. Using the AFIRS maintenance terminal (ref. section 8.1), navigate to the AFIRS Home page. 2. Confirm the correct date, time, and position (DTP) information is displayed. 3. Note the DTP source being used. If it is an external source, disable that source and confirm that a different source is being used. Repeat until the system is using the internal GPS source (if configured active). 4. Restore all disabled DTP sources. 9.1.4.2 Satcom Tests 1. Confirm Iridium satellite network availability (e.g. Ready to Connect indication on the MCDU or ISVM indicator on DMU front panel is green). 2. Using an MCDU or Dial Pad, place a voice call to a ground station. Confirm proper cockpit indications for a call in progress. 3. Terminate the call from the cockpit. Confirm proper cockpit indications for the Ready to Connect state. 4. Place a call from a ground station to the aircraft. Confirm proper cockpit indications for an incoming call. Answer the call and confirm proper cockpit indications for a call in progress. 5. Conference in each other extension available in the aircraft. Confirm proper extension ringing function, conference call functionality, and cockpit indications. 6. Leave the conference call from Extension 1. Confirm the call is still in progress from the remaining extension(s). Confirm proper cockpit indications for a cabin call in progress. 7. Preempt the cabin call and confirm that the cockpit now has control of the voice channel. Confirm proper cockpit indications. 8. Place a call from a ground station to the aircraft. Reject the call. Confirm proper cockpit indications. 9. Place a call from a ground station to the aircraft. Allow call to go unanswered. Confirm proper ring sequencing, eventual call termination, and proper cockpit indications. 10. Place a call from a cabin extension to a ground station. Confirm proper cockpit indications for a cabin call in progress. Set up a camp-on call from the cockpit. Terminate the call in the cabin and confirm that the camped-on call is automatically initiated. Confirm proper cockpit indications. 11. Terminate call at the ground station. Confirm proper cockpit indications. 12. Select the Cabin Lock function and confirm proper cockpit indications. Confirm that cabin extensions cannot place a voice call. 13. If configured to be able to turn Iridium Off with the All Off option, turn Iridium Off and confirm proper cockpit indications. Confirm that a voice call cannot be made to or from the aircraft. Turn Iridium back on and confirm proper operation and cockpit indications. Page 78 Confidential and Proprietary to FLYHT Aerospace Solutions Ltd. 250-0019 Rev. --

22 April 2013 AFIRS 228 Series Installation Manual 9.1.4.3 Datalink Tests 1. If Uptime access is available, confirm the power-on report has been received from the aircraft. 2. Confirm EFB datalink functionality is available. 3. If so configured, turn Iridium Off and confirm proper cockpit indications. Confirm that data transmissions cease from the aircraft. Turn Iridium back on and confirm proper operation and cockpit indications. 9.1.5 EMI Tests Each AFIRS aircraft installation should be tested for electromagnetic interference in accordance with procedures developed by the aircraft systems integrator. The tests should be developed to ensure that there is no objectionable interference between the AFIRS and other aircraft systems. This can include ground tests with engine running and flight tests as required. 9.2 The aircraft systems integrator is responsible to provide Instructions for Continues Airworthiness

(ICA) for the AFIRS system specific to the aircraft installation. The general content in this Installation Manual may be referenced by the aircraft systems integrator when developing the ICA. Instructions for Continued Airworthiness 250-0019 Rev. --

22 April 2013 Confidential and Proprietary to FLYHT Aerospace Solutions Ltd. Page 79 AFIRS 228 Series Installation Manual THIS PAGE INTENTIONALLY LEFT BLANK Page 80 Confidential and Proprietary to FLYHT Aerospace Solutions Ltd. 250-0019 Rev. --

22 April 2013 AFIRS 228 Series Installation Manual Appendix A ICT Worksheet ICTGroup AircraftInfo Iridium ICTParameterName Model/Type(Text24Characters) SerialNumber(Text24Characters) SDUNo. IridiumDataMode GPS InternalGPS ARINC717 Format BusSpeed Value SDU1 SDU2 DEDICATED MULTIPLEXED ACTIVE INACTIVE NONE HBP BPRZ 64STD 64REV 128 256 512 1024 ICAO 1 Function DTP NONE GENERIC429 ACARS1 ACARS2 AIRBUSCFDS A702/AFMS1 A702/AFMS2 A702/AFMS3 GAMA429FMS1 GAMA429FMS2 GAMA429FMS3 CMA9000FMS1 CMA9000FMS2 CMA9000FMS3 250-0019 Rev. --

22 April 2013 ICTARINC429Receivers 8 2 3 4 5 6 7 9 10 11 12 13 14 15 16 Confidential and Proprietary to FLYHT Aerospace Solutions Ltd. Page 81 AFIRS 228 Series Installation Manual Function BASICDTP1 BASICDTP2 PL4/21GPBUS51 PL4/21GPBUS52 A739MCDU1 A739MCDU2 A739MCDU3 MODES1 MODES2 Speed Parity DTP LO HI ODD EVEN NONE ICAO 1 ICTARINC429Receivers 2 8 3 4 5 6 7 9 10 11 12 13 14 15 16 Function NONE A739MCDU ACARS(228SOnly) GPBUS1 GPBUS2 GPBUS3 GPBUS4 ICTARINC429Transmitters 3 1 2 LO HI Speed 4 5 6 Page 82 Confidential and Proprietary to FLYHT Aerospace Solutions Ltd. 250-0019 Rev. --

22 April 2013 AFIRS 228 Series Installation Manual ICTSerialPorts Parameter 5 6 7 8 NONE ODD EVEN 1 2 NONE XON/XOFF RTS/CTS 1 2 3 4 DataBits Parity StopBits FlowControl ICTSerialPorts Function Receive 3 2 4 1 NONE GENERIC EFB1 EFB2 EFB3 Type Speed 232 422 2.4 4.8 9.6 19.2 Transmit 2 3 4 1 ICTEthernetPorts Function NONE NOTMONITORED MONITORED 1A 2B 3B 4B 250-0019 Rev. --

22 April 2013 Confidential and Proprietary to FLYHT Aerospace Solutions Ltd. Page 83 AFIRS 228 Series Installation Manual Function NONE GENERIC CABINLOCK CHIMERESET ENDCALL EVENT IRIDIUMOFF MICON PARKBRAKE SYSRESET WOW2 Signal Logic OPEN/GND OPEN/28V ACTIVELO ACTIVEHI 2 ICTDiscreteInputs 7 3 4 5 6 8 9 10 11 12 13 14 15 Function NONE CABINLOCK CALLLIGHT EXT2CALL EXT3CALL GPSLINK IRIDIUMOFF ISVMLINK ISDMLINK(228SOnly) TEXTMSG ICTDiscreteOutputs 3 ACTIVELO ACTIVEHI ActiveTime(100to6,000ms) InactiveTime(100to6,000ms) 1 2 4 5 7 8 6 ______ms ______ms Logic Chime Page 84 Confidential and Proprietary to FLYHT Aerospace Solutions Ltd. 250-0019 Rev. --

22 April 2013 AFIRS 228 Series Installation Manual Satcom Extension1 Location ICTParameterName SidetoneLevel(20to3dB) NoiseCancelling MicOnConfig ControlSource Extension2 MicGain(PreADC)(0to59dB) Location Volume(1to5dB) SidetoneLevel(20to3dB) NoiseCancelling Extension3 Location Volume SidetoneLevel(20to3dB) NoiseCancelling Value NONE COCKPIT CABIN ____dB ENABLED DISABLED SWITCHEDPTT LATCHEDACP MCDU EXT3DTMF ____dB NONE COCKPIT CABIN ____dB ____dB ENABLED DISABLED NONE COCKPIT CABIN ____dB ____dB ENABLED DISABLED 250-0019 Rev. --

22 April 2013 Confidential and Proprietary to FLYHT Aerospace Solutions Ltd. Page 85 AFIRS 228 Series Installation Manual THIS PAGE INTENTIONALLY LEFT BLANK Page 86 Confidential and Proprietary to FLYHT Aerospace Solutions Ltd. 250-0019 Rev. --

22 April 2013 AFIRS 228 Series Installation Manual Appendix B ORT Worksheet ORTGroup AircraftInfo FDM Power Management MCDU ORTParameterName Registration/FIN(Text24Characters) ICAO24BitAddress ReservedSpace(0.1to4.0GB) ShutdownDelayTime(0to60min.) SystemName CallPriorityName(14) AllowIridiumOff Iridium IridiumOffMode AirToGround Calls ChimeonConnect CIPTransition CallProgressTones DefaultCall Priority Extension1 Extension2 Extension3 DirectoryCount(1to10) Directory1Name

(Text10Characters) Directory

(Ext1Only) 250-0019 Rev. --

22 April 2013 Value ______GB ALWAYSON ______min. AFIRS SATCOM AFIR/SATCM EMERGENCY,SAFETY,NONSAFETY, PUBLIC EMERGENCY,OPERATIONALHIGH, OPERATIONALLOW,PUBLIC YES NO ALLOFF DATAOFF YES NO INITIATED CONNECTED NORTHAMERICAN EUROPEAN 1 2 3 4 1 2 3 4 1 2 3 4 Confidential and Proprietary to FLYHT Aerospace Solutions Ltd. Page 87 AFIRS 228 Series Installation Manual ORTGroup ORTParameterName Value Directory2Name

(Text10Characters) Directory3Name

(Text10Characters) Directory4Name

(Text10Characters) Directory5Name

(Text10Characters) Directory6Name

(Text10Characters) Directory7Name

(Text10Characters) Directory8Name

(Text10Characters) Directory9Name

(Text10Characters) Directory10Name

(Text10Characters) Ext1 Ext2 Ext3 AllowManual Dialing GroundtoAir Calls AllowLowPriorityCallsinCockpit RingType SequentialRing RingOrder Ext1RingCount(3to10) Ext2RingCount(3to10) Ext3RingCount(3to10) ConcurrentRing RingCount(3to10) YES NO YES NO YES NO YES NO CONCURRENT SEQUENTIAL 123 132 213 231 312 321 Page 88 Confidential and Proprietary to FLYHT Aerospace Solutions Ltd. 250-0019 Rev. --

22 April 2013 AFIRS 228 Series Installation Manual ORTGroup ORTParameterName Value Ext1Ring Ring Call_Light/Chime RingTone Ext2Ring Ring ReRingTime(1to10) ReRingCount(1to10) Call_Light Ext3Ring Ring ReRingTime(1to10) ReRingCount(1to10) Call_Light ServiceProvider SafetyServices

(228SOnly) YES NO FLASHING/MULTISTROKE FLASHING/SINGLESTROKE STEADY/SINGLESTROKE YES NO YES NO FLASHING STEADY YES NO FLASHING STEADY ARINC SITA 250-0019 Rev. --

22 April 2013 Confidential and Proprietary to FLYHT Aerospace Solutions Ltd. Page 89 AFIRS 228 Series Installation Manual THIS PAGE INTENTIONALLY LEFT BLANK Page 90 Confidential and Proprietary to FLYHT Aerospace Solutions Ltd. 250-0019 Rev. --

22 April 2013 AFIRS 228 Series Installation Manual Appendix C Environmental Qualification Forms The following two forms are provided for the AFIRS 228B DMU and AFIRS 228 ACM respectively. 250-0019 Rev. --

22 April 2013 Confidential and Proprietary to FLYHT Aerospace Solutions Ltd. Page 91 AFIRS 228 Series Installation Manual RTCA DO-160F Environmental Qualification Form Nomenclature: Data Management Unit (DMU) Model:

Part Number:

Manufacturer:

AFIRS 228B 502-2001-01 FLYHT, 200W, 1144 29 Avenue NE, Calgary, AB, Canada T2E 7P1 Conditions Section Description of Tests Conducted Temperature and Altitude In-Flight Loss of Cooling Temperature Variation Humidity Operational Shock & Crash Safety Vibration Explosive Atmosphere Waterproofness Fluids Susceptibility Sand & Dust Fungus Salt Fog Test Magnetic Effect Power Input Voltage Spike Audio Frequency Susceptibility Induced Signal Susceptibility Radio Frequency Susceptibility Radio Frequency Emission Lightning Induced Transient Susceptibility Lightning Direct Effects Icing Electrostatic Discharge Fire, Flammability Remarks:

4.0 4.5.5 5.0 6.0 7.0 8.0 9.0 10.0 11.0 12.0 13.0 14.0 15.0 16.0 17.0 18.0 19.0 20.0 21.0 22.0 23.0 24.0 25.0 26.0 Categories A2, F2 Category X (not tested) Category B Category A Category D Categories S (Curves C & L), U2 Category X (not tested) Category X (not tested) Category X (not tested) Category X (not tested) Category X (not tested) Category X (not tested) Category Z Category Z (XI) Category A Category Z Category ZW Category ST Category M Category X (not tested) Category X (not tested) Category X (not tested) Category A Category C 1. Section 26.0 was tested as per DO-160G; all other tests as per DO-160F. Page 92 Confidential and Proprietary to FLYHT Aerospace Solutions Ltd. 250-0019 Rev. --

22 April 2013 AFIRS 228 Series Installation Manual RTCA DO-160F Environmental Qualification Form Nomenclature: Aircraft Configuration Module (ACM) Model:

Part Number:

Manufacturer:

AFIRS 228 502-3001-01 FLYHT, 200W, 1144 29 Avenue NE, Calgary, AB, Canada T2E 7P1 Conditions Section Description of Tests Conducted Temperature and Altitude In-Flight Loss of Cooling Temperature Variation Humidity Operational Shock & Crash Safety Vibration Explosive Atmosphere Waterproofness Fluids Susceptibility Sand & Dust Fungus Salt Fog Test Magnetic Effect Power Input Voltage Spike Audio Frequency Susceptibility Induced Signal Susceptibility Radio Frequency Susceptibility Radio Frequency Emission Lightning Induced Transient Susceptibility Lightning Direct Effects Icing Electrostatic Discharge Fire, Flammability Remarks:

4.0 4.5.5 5.0 6.0 7.0 8.0 9.0 10.0 11.0 12.0 13.0 14.0 15.0 16.0 17.0 18.0 19.0 20.0 21.0 22.0 23.0 24.0 25.0 26.0 Categories A2, F2 Category X (not tested) Category B Category A Category D Categories S (Curves C & L), U2 Category X (not tested) Category X (not tested) Category X (not tested) Category X (not tested) Category X (not tested) Category X (not tested) Category Z Category Z (XI) Category A Category Z Category ZW Category ST Category M Category X (not tested) Category X (not tested) Category X (not tested) Category A Category C 1. Section 26.0 was tested as per DO-160G; all other tests as per DO-160F. 250-0019 Rev. --

22 April 2013 Confidential and Proprietary to FLYHT Aerospace Solutions Ltd. Page 93 AFIRS 228 Series Installation Manual FLYHT Aerospace Solutions Ltd. 200W, 1144 29th Avenue NE Calgary, Alberta, Canada T2E 7P1 Telephone: 1-403-250-9956 Toll Free: 1-866-250-9956 Fax: 1-403-291-9717 E-mail: support@flyht.com Website: http://flyht.com Page 94 Confidential and Proprietary to FLYHT Aerospace Solutions Ltd. 250-0019 Rev. --

22 April 2013