Introduction FTr16S AFHDS 3 PPM i-BUS Receiver overview VCC PPM i-BUS GND SENS The FTr16S is a double antenna bidirectional receiver using the AFHDS 3 protocol. It's compact, easy to install and can output using a standard PPM or i-BUS signal. VCC 3.5~8.4V PPM PPM i-BUS i-BUS SENS:
GND These ports connect the receiver to various models, component's and flight controllers. VCC: Power supply voltage from 3.5 8.4V. PPM signal port: Outputs standard PPM signal. i-BUS signal port: Outputs i-BUS signal. SENS: Sensor. GND: Connect to ground wire. 1 NV14, FS-i10Paladin (PL18) Attention:
Make sure the product is installed and calibrated correctly, failure to do so may result in serious injury. Make sure the receiver's battery is disconnected before turning off the transmitter, failure to do so may lead to unintended operation or loss of control. Make sure the receiver is mounted away from motors, electronic speed controllers or any device that emits excessive electrical noise. Keep the receiver's antenna at least 1cm away from conductive materials such as carbon or metal. Do not power on the receiver during the setup process to prevent loss of control. The receiver can receive at distances further than it can transmit from. When the receiver goes out of its transmission range, some transmitter's will sound the lost signal alarm. This is normal, the lost signal alarm can be turned off in the settings for transmitters such as the NV14, FS-i10 and Paladin (PL18). Binding 1. 2. LED LED LED LED 3. 1. First put the transmitter into bind mode (see the transmitter's user manual for instructions on how to activate bind mode.) 2. Press receiver's bind key and connect the receiver to power at the same time. The receiver's green LED will start to flash quickly indicating that it has entered bind mode. When the receiver's green LED stops flashing the transmitter and receiver have successfully bound. When the receiver's red LED flash slowy indicating losing signal. FTr16S Receiverhttp://www.flysky-cn.comCopyright 2019 Flysky Technology co., ltd Binding If there is a critical hardware error the LED will remain red. 3. Check to make sure that the transmitter and receiver are working as expected, if there are any issues or unexpected operation follow the steps above to bind again. Product specification 16 PPM/i-BUS 2.402-2.480GHz
<20dBmEU RF AFHDS 3 20ms 3.5 8.4V LED 1 1000m 1500us900 2100us 20*12*3.1mm
<2g CEFCC IDN4ZFTR16S00 Certification FCC Compliance Statement Channels: 16 Model Type: Racing Drone Data Output: PPM/i-BUS Frequency Range: 2.402-2.480GHz Transmission Power: <20dBm(EU) RF Standard: AFHDS 3 Channel Latency: <20ms Antenna: Double Antenna Input Power: 3.5-8.4V Display: LED Indicator Online Update: Yes Range without interference 1m from the ground :
more than 1000m Channel Data: 1500usRange900 2100us Dimensions: 20*12*3.1mm Weight: <2g Certification: CEFCC ID: N4ZFTR16S00 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Warning: changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. DoC Declaration Hereby, [Flysky Technology co., ltd] declares that the Radio Equipment [FTr16S] is in compliance with RED 2014/53/EU. The full text of the EU DoC is available at the following internet address: www.flysky-cn.com. CE Warning The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20cm from all persons and must not be co-located or operating in conjunction with any other transmitter. End-users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. Environmentally friendly disposal Old electrical appliances must not be disposed of together with the residual waste, but have to be disposed of separately. The disposal at the communal collecting point via private persons is for free. The owner of old appliances is responsible to bring the appliances to these collecting points or to similar collection points. With this little personal effort, you contribute to recycle valuable raw materials and the treatment of toxic substances. CAUTION RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS FCC ID: N4ZFTR16S00 FTr16S Receiverhttp://www.flysky-cn.comCopyright 2019 Flysky Technology co., ltd