Digital propotional radio control systemRED I3 7. Transmitter specifications Transmitter specifications:
Channels: 2 Model type: car/boat RF range:2.405-2.475GHz Bandwidth:500KHz Band:142 RF power: less than18 dBm 2.4G system: AFHDS2A and AFHDS Code type: GFSK Sensitivity: 1024 Low voltage warning: less than 4.2V DSC port: Micro-USB PPM ST range:70 L:35 R:35 TH range:45 F:35 B:15 Charger port: no ANT length: 26mm Weight: 323g Power: 6V DC 1.5AA*4 Display mode:LED indicator Size: 150*80*196mm Color: blacK 2
/
2.405-2.475GHz 500KHz 142 18dBm 2.4G(
GFSK 1024 4.2V Micro-USB PPM 453515 26 323 6V DC 1.5AA*4 LED 150*80*196 8.Receiver specifications MODEL: FS-A3 SPECIFICATIONS Channels: 3 Model type: car/boat RF range: 2.405-2.475GHz Bandwidth: 500KHz Band sum: 142 RF.receiver sensitivity: -105dBm 2.4G system: AFHDS 2A Code type: GFSK Sensitivity: 1024 Power: 4.0-6.5V DC ANT lenght: 26mm Weight: 5g Size: 35*22*12mm Color: black Certificate: CE FCC RED I3 3
/
: 2.405-2.475GHz 500KHz 142
-105dBm 2.4G GFSK 1024 4.0-6.5V DC 26 5 35*22*12 CE FCC 9.Receiver and servo connections 9.01. Installation when a motor controller is used Remark: Place the receiver antenna upright and perpendicular to the horizontal plane Keep the receiver antenna away from any metal objects to ensure max sensitivity. (See pic1) 1 ANT Receiver Figure1(1 Digital propotional radio control systemRED I3 9.02. Installation for gas powered models 9.03. Suggestions for RX fail safe setting. 1 2 1 2 It is set in the middle of the trigger, which fits the electric vehicle. It is set in brake, which fits the gas vehicle. 2.4G 10. 2.4GHz Operation notes 10.01. Matching(code)/Binding All receivers are already paired with their respective transmitter during production. If you wish to bind it with another transmitter, please follow the instructions below. Remark: FS - brand system are not compatible with other brands Steps:
1. Ensure you are using AFHDS2A system 2. Correctly install the battery inside 2.4G transmitter w/o powering it on. 3. Insert the binding plug into the BIND channel slot on the receiver. (Figure.1). 4. Using a correct receiver battery pack, plug it in to VCC channel slot on the receiver. At this time, the LED on receiver should flash, indicating receiver has entered bind status. 5. Press and hold the binding button on transmitter, and then switch on the transmitter. 6. Observe the LED light on the receiver. If LED stops flashing, and stays lit permanently, the binding procedure is completed.
(This process takes approximately 5S.) 7. Release hold the binding button on the transmitter, and unplug the bind cable. 8. Install the servos to test. 9. If the system does not work properly, repeat the procedure.
(The above binding instruction is only suitable for any FLYSKY 2.4G products) 1.AFHDS2A 2.2.4G 3.BIND1) 4.VCCLED 5.BIND) 6.LEDLED5S 7. 8. 9.NG FLYSKY2.4G Bind key LED Battery Match line Receiver Figure1(1 Digital propotional radio control systemRED I3 10.02 Power on A. Connect every part. B. Switch on the power supply of the transmitter. C. Connect the power supply of the receiuer. D. Receive LED light solid. E. Finish and use. 1. 2. 3. 4.LED 5. Tx power ON Rx power ON 10.3 Shut down A. Connect every part. B. Cut off the transmitter power supply. 1. 2. Rx power off Tx power off 11. each part of the transmitter Front 10 11 4 2 8 9 6 5 12 13 14 1 7 3 1 2 3 4 5 6 7 BIND Key POWER LED Ch1 CH1 REV POWER ON/OFF LED Ch1 CH1 TRIM Ch2 CH2 REV 8 Ch2 CH2 TRIM 9 Ch1 CH1 D/R 10 POWER CHECK 11 Ch2 CH2,M,P 12 STEERING WHEEL 13 THROTTLE TRIGGER 14 BAT BOX TH,M,P On some model, the travel of the throttle is not equal to the travel of the brakes.This function sets the position of the middle point between the throttle and the brakes.Throttle proportion can be set from 5:5 to 7:3 when mechanical angle of the radio is not modified. 5:57:3 Digital propotional radio control systemRED I3 13. Failsafefunction 13.01 Failsafe Instruction FAIL SAFE FUNCTION 1.Function Failsafe aims to prevent out-of-control driving of RC car orRC boat.If the Receiver is not able to receive any signal,from the control to throttle,the parameter of throttle on receiver will turn back to its original setting. 2.Setting a.Turn on the Transmitter switch;
b.Turn on the Receiver switch.the LEDwill be lighting;
c.Adjust Transmitter's Throttle,make the car/boat to stop or flameout,then keep still. d.Press the "Setting"button on Receiver(as the pic below).the LEDwill be flashing,then stop after 3seconds around,which means setting finished. 3.Testing a.Turn on the Transmitter switch;
b.Turn on the Receiver switch;
c.Turn off the transmitter switch;
d.Servo of throttle will turn back to its original setting automaticlly'
e.Setting is successful if above procedures finished completely. 1. 2. a. b. c. d. LED3 e. 3. a. b. c. d. e. OK FCC Statement FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or televison reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help. To assure continued compliance, any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate this equipment. (Example use only shielded interface cables when connecting to computer or peripheral devices). This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be collocated or operating in conjunction with any other antenna or transmitter Caution!
The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user authority to operate the equipment. 6