Quick Start Guide FS-G7P www.flyskytech.com. VR2 SW3 TR1 AA AA 1. 2. 4 3. SW2
(4*AA ) 2.4GHz Flysky Technology co., ItdFS-G7P RED2014/53/EU. DoC FCC www.flysky-cn.com 20cm RF SW1 VR1 TR
LED
Copyright 2021 Flysky Technology co., ltd
(ON/OFF) VR2 1. > >
USB Type C USB 2. 3. 1. 2. [ON] LED 1. / [ ] ;
2. / [ ] [ANT 2 WAY], ;
1. 3. / [ ] / [ ]
2. [OFF]
4. 5. LED 6. 1. [ ] [ANT 1 WAY]
LED 2. FLYSKY FS-G7P 4. VR2 VR2 5.
i-BUS/PPM/PWM [ ][ ] [ ]
[ ] PWM ;
[ ] 1~7 1. PPM/i-BUS/S.BUS [ ]
2. S.BUS 3. PPM/i-BUS [ ] [
4. FS-G7P 7
<20dBm ANT AA <4.2V 1.5AA*4
-10 ~ +60 20% ~ 95 2.4GHz ISM 128*64 LCD 1024 136.4*111.8*197.5mm PWM/PPM/i-BUS/S.BUS 305g CEFCC ID: N4ZG7P00 300m( ) Thank you for purchasing the products of Flysky! To find out more about our products, visit our website at www.flysky-
cn.com. If you encounter any problems during using,Please refer to the manual first. If the problem is still not resolved, contact your local dealer directly or contact the customer service staff via Flysky official website. Precautions Read the safety messages listed below before operation!
Do not use the product at night or during bad weather conditions, like rain or thunderstorms. It can cause erratic operation or loss of control. Do not use the product when visibility is limited. Do not expose the product to rain or snow. Any exposure to moisture (water or snow) may cause erratic operation or loss of control. Interference may cause loss of control. To ensure the safety of you and others, do not operate in the following places:
Transmitter Overview VR2 Three-position Knob SW3 Three-position Switch TR1 Button Steering Wheel Throttle Trigger SW2 Button Basic Operations Install the AA Battery Follow the steps below to install the AA batteries:
1. Open the battery compartment cover as illustrated. 2. Insert 4 fully-charged AA batteries into the compartment. Make sure that the batteries are well set according to the polarities marked on the battery compartment. 3. Replace battery compartment cover. Battery Compartment
(4*AA Battery) Press to slide as illusrtated. Remove the cover. Digital Proportional Radio Control System FCC ID: N4ZG7P00 ManufacturerFLYSKY Technology Co., Ltd Address: 16F, Huafeng Building, 6006 Shennan Road, Futian District, Shenzhen Figures and illustrations in this manual are provided for reference only and may differ from actual product appearance. Product design and specificatiions may be changed without notice. Near any sites where other radio control activity may occur Near people or roads On any pond/lake when passenger boats are present Near power lines or communication broadcasting antennas Do not use this product when you are tired, uncomfortable, or under the influence of alcohol or drugs. Doing so may cause serious injury to yourself or others. The 2.4GHz radio band is limited to line of sight. Always keep your model in sight as a large can block the RF Never grip the transmitter antenna during operation. It significantly degrades signal quality and strength and signal and lead to loss of control. may cause loss of control. Do not touch any part of the model that may generate heat during operation, or immediately after use. The engine, motor or speed control, may be very hot and can cause serious burns. Misuse of this product may lead to serious injury or death. To ensure the safety of you and your equipment, read this manual and follow the instructions carefully. Make sure the product is properly installed in your model. Failure to do so may result in serious injury. Make sure that the receiver's battery is disconnected before turning off the transmitter. Failure to do so may lead to unintended operation and cause an accident. Ensure that all motors operate in the correct direction. If not, adjust the direction first. Make sure that the model stays within range in order to prevent loss of control. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-lacated or operating in conjunction with any other transmitter.End-users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. Hereby, [Flysky Technology co., ltd] declares that the Radio Equipment [FS-G7P] is in compliance with RED The full text of the EU DoC and Appendix 1 of the FCC Statement are available at the following internet 2014/53/EU. address: www.flysky-cn.com CAUTION!
RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS. Changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment. SW1 Button VR1 Knob Five-way Switch (TR) Left/Right: Steering trim Front/Back: Throttle trim Display LED Indicator Five-way Switch
( menu navigation) Up/Down: Page Up/Down Right: To enter the next level menu Left: To return to the previous menu Center: To confirm Power Switch
(ON/OFF) Lanyard Hole Cell Phone Holder Connection Hole USB Port (Type C) Firmware updating/USB emulator/
Power supply for the transmitter Power on Follow the steps below to turn on the transmitter:
1. Check to make sure that the batteries are fully charged and installed correctly. 2. Toggle the switch to the [ON] position. The LED indicator will be lit. For safety, power on the transmitter first, then the receiver. Binding The transmitter and receiver have been pre-bound before delivery. If you are going to use another receiver, follow the steps below to rebind. The transmitter supports two-way binding and one-way binding. The transmitter will display the information returned from the receiver after the two-way binding is completed. 1. Turn on the transmitter, then press Center to enter the main menu. Press Up/Down to select the [RX SETUP]
and press Center to enter [RX SETUP] menu. 2. Press Up/Down to navigate to the [RF Standard], then press Center to enter and set the RF standard to [ANT Press Left to return to the previous menu. 2 WAY]
. 3. Press Up/Down to navigate to the [RX SETUP] and press Center to enter [RX SETUP] menu. Then press Up/Down to navigate to the [BIND SETTING] and press Center to enter. Press Up/Down to navigate to the
[BINDING : START] and press Center to put the transmitter to enter bind mode. 4. Put the receiver to enter bind mode. 5. The binding process is completed when the LED of the receiver stops flashing and is solid on ( The 6. Check to make sure the transmitter and receiver are working correctly, if there are any issues or unexpected transmitter will exit the bind mode automatically). operation arise, follow the steps above to bind again. Notes:
1. If the transmitter that has its radio frequency (RF Standard) set to ANT 1 WAY enters bind mode, the LED of the receiver will be in slow flashing state. You need to put the transmitter to exit bind mode manually and if the LED of the receiver stops flashing and is solid on, indicating that the binding is completed. 2. The binding steps may vary according to the receiver model. Visit the Flysky official website to check the manual of the receiver or other relevant information. Stick Calibration To calibrate the Max/Min range of the throttle trigger, steering wheel and VR2 knob. The transmitter is calibrated before leaving the factory, however if recalibration is required, please follow these steps:
Digital Proportional Radio Control System FS-G7P 1. Put the transmitter to enter the [ Stick Calibration] mode.(Main menu> SYSTEM SETTING>STICK ) 2. Steering wheel calibration: Turn the wheel to the Max/Min endpoint in a clockwise/counterclockwise direction. 3. Throttle Trigger calibration: Push/pull the trigger forward/backword to the Max/Min endpoint. 4. VR2 calibration: Turn the VR2 knob to the Max/Min endpoint in a clockwise/counterclockwise direction. 5. Press Left to save and exit. Failsafe The failsafe function is used to output the channel value according to the out-of-control protection value set by the user after the receiver loses its signal and is out of control to protect the model and personnel. For i-BUS/PPM/PWM. It can be set to [NOT SET], [ON] or [OFF].
[OFF] It is no output for the interface of PWM.
[NOT SET] Failsafe is not set.
[ON] CH1-CH7 are respectively set with a fixed failsafe value. By default, this value is the reading of current channel output value. You can toggle the corresponding control to the desired position and hold it. After pressing Left to return, the setting is saved. Notes:
1. For bus signal types such as PPM/i-BUS/S.BUS, a single or several of these channels are not allowed to be in [OFF] mode. The actual signal is held at the last output value when the channel is set to [OFF] mode. 2. Because the S.BUS signal information contains failsafe flag bits, the failsafe settings of each channel are communicated to subsequent devices by the failsafe flag bits. If the connected devices support the failsafe flag bit analysis, the failsafe values set for each channel are output after out of control. 3. For the signal PPM/i-BUS without failsafe flag bits, it supports the setting of the signal to [OFF] mode in case of out of control. After setting to [OFF] mode, regardless of the setting of the failsafe of each channel, each channel will be in [No output] mode after out of control. The failsafe function has no default set at the factory and as such must be set manually. If no failsafe setting has been set, then the receiver will not output anything when signal is lost. 4. Power Off Follow the steps below to turn off the transmitter:
1. Turn off the receiver first. 2. Toggle the transmitter's power switch to the [OFF] position to turn off the transmitter. Make sure to disconnect the receiver power before turning off the transmitter. Failure to do so can result out of control. Unreasonable setting of the Failsafe may cause accidents. Specifications Product Name Channels RF Adaptive Model Maximum Power 2.4GHz system Display Resolution Data Output Charging Jack Distance FS-G7P 7 2.4GHz ISM Cars, boats
<20dBm (e.i.r.p.) (EU) ANT 128*64 LCD(Black and white dot matrix screen) Color 1024 PWM/PPM/i-BUS/S.BUS NO 300m (Ground distance without interfence) Dimension Weight Langages Certifications Low Voltage Alarm AA battery: <4.2V 1.5AA*4 Battery Built-in single coaxial cable antenna Antenna Online Update Yes Temperature Range -10 Humidity Range
~ +60 20% ~ 95 Black 136.4*111.8*197.5mm 305g Chinese, English CE, FCC ID: N4ZG7P00 Http://www.flysky-cn.comCopyright 2021 Flysky Technology co., ltdRelease date: 2021-09-12