FCC ID: XHM-220808 Intel WiFi 6E AX210 Module

USER MANUAL Version 2.1 August 2022 M276 & M278 Copyright Copyright 2022 All Rights Reserved Manual Version 2.1 The information contained in this document is subject to change without notice. We make no warranty of any kind with regard to this material, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. We shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material. This document contains proprietary information that is protected by copyright. All rights are reserved. No part of this document may be photocopied, reproduced or translated to another language without the prior written consent of the manufacturer. TRADEMARK The material in this manual is subject to change without notice. Bluetooth is a registered trademark of Bluetooth SIG. Microsoft , Windows and ActiveSync are either registered trademarks or trademarks of Microsoft Corporation. All other product or service names are the property of their respective owners. ii Safety Regulatory Information Caution: Only use approved and UL Listed accessories, battery packs and battery chargers. Do NOT attempt to charge damp/wet mobile computers or batteries. All components must be dry before connecting to an external power source. Power Supply Use only the approved power supply output rated 12 Vdc and minimum 3 A. The power supply is certified to EN60950-1 or EN62368-1 with SELV outputs. Use of alternative power supply will invalidate any approval given to this device and may be dangerous. Warning for Use of Wireless Devices Please observe all warning notices with regard to the usage of wireless devices. Potentially Hazardous Atmospheres You are reminded of the need to observe restrictions on the use of radio devices in fuel depots, chemical plants etc. and areas where the air contains chemicals or particles

(such as grain, dust, or metal powders) and any other area where you would normally be advised to turn off your vehicle engine. Safety in Aircraft Switch off your wireless device whenever you are instructed to do so by airport or airline staff. Pacemakers Pacemaker manufacturers recommended that a minimum of 15cm (6 inches) be maintained between a handheld wireless device and a pacemaker to avoid potential interference with the pacemaker. These recommendations are consistent with independent research and recommendations by Wireless Technology Research. Persons with Pacemakers Persons with Pacemakers should ALWAYS keep the device more than 15cm (6 inches) from their pacemaker when turned ON and hence they should not carry the device in a breast pocket . Should use the ear furthest from the pacemaker to minimize the potential for interference. If you have any reason to suspect that interference is taking place, turn OFF your device. iii Hearing Aids The wireless device may interfere with some hearing aids. In the event of interference you may want to consult your hearing aid supplier to discuss solutions. Other Medical Devices Please consult your physician or the manufacturer of the medical device, to determine if the operation of your wireless product may interfere with the medical device. FCC/EU RF Exposure Guidelines FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Connect the equipment into an outlet on a circuit different from that to which the Increase the separation between the equipment and receiver. receiver is connected. Consult the dealer or an experienced radio/TV technician for help. This device complies with FCC SAR exposure limits set forth for an uncontrolled environment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC RF Radiation Exposure Statement:

This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. For body worn operation, this device has been tested and meets FCC RF exposure guidelines. When used with an accessory that contains metal may not ensure compliance with FCC RF exposure guidelines. iv Caution!

Any changes or modifications not expressly approved by the party responsible for compliance could void t he user's authority to operate the equipment. CE Marking and European Economic Area The use of 2.4GHz WLAN's, for use through the EEA, have the following restrictions:

Maximum radiated transmit power of 100 mW EIRP in the frequency range 2.400 -2.4835 GHz France, outside usage is restricted to 2.4 - 2.454 GHz. Italy requires a user license for outside usage. For class 2 device (supporting WLAN 5GHz: 5150-5350 MHz) The device is restricted to indoor use only when operating in the 5150 to 5350 MHz frequency range in the following countries:

AT BE BG HR CY CZ DK EE IT FI LV FR DE EL HU IE LT LU MT NL PL PT RO SK SI ES SE UK BLE Wireless Technology for use through the EEA has the following restrictions:

Maximum radiated transmit power of 100mW EIRP in the frequency range 2.400 -2.4835 GHz France, outside usage is restricted to 10mW EIRP Italy requires a user license for outside usage. Battery Information Our rechargeable battery packs are designed and constructed to the highest standards within the industry. However, there are limitations to how long a battery can operate or be stored before needing replacement. Many factors affect the actual life cycle of a battery pack, such as heat, cold, harsh environmental conditions and severe drops. When batteries are stored over six (6) months, some irreversible deterioration in overall battery quality may occur. Store batteries discharged in a dry, cool place, removed from the equipment to prevent loss of capacity, rusting of metallic parts and electrolyte leakage. When storing batteries for one year or longer, they should be charged and discharged at least once a year. If an electrolyte leakage is observed, avoid any contact v with affected area and properly dispose of the battery. Batteries must be charged within the 32 to 95 F (0 to +35 C) ambient temperature range. Replace the battery when a significant loss of run time is detected. Battery Caution Risk of explosion if battery is replaced by an incorrectly type. Dispose of used battery according to the local disposal instructions. Waste Electrical and Electronic Equipment (WEEE) English: For EU Customers: All products at the end of their life must be returned to the reseller for recycling. Notational Conventions The following conventions are used in this document:

Italics are used to highlight specific items in the general text, and to identify chapters and sections in this and related documents. bullets () indicate:

action items lists of alternatives lists of required steps that are not necessarily sequential Sequential lists (e.g., those that describe step-by-step procedures) appear as numbered lists. NOTE This symbol indicates something of special interest or importance to the reader. Failure to read the note will not result in physical harm to the reader, equipment or data. CAUTION This symbol indicates that if this information is ignored, the possibility of data or material damage may occur. WARNING! This symbol indicates that if this information is ignored the possibility that serious personal injury may occur. vi Revision History Version Date Description 1.0 2.0 2.1 April 2021 Initial release June 2021 August 2022 Add FCC RF Radiation Exposure Statement Specification update F33 motherboard added vii Table of Contents 1 Item Checklist ............................................. 9 1-1 1-2 Standard Items ................................................................................... 9 Optional Items .................................................................................. 10 2 System View .............................................. 11 2-1 2-2 2-3 Front View ......................................................................................... 11 Rear View .......................................................................................... 12 Specification ..................................................................................... 13 3 Getting Started ......................................... 15 3-1 3-2 3-3 3-4 Power On/Off the System ................................................................ 15 Installing the Peripheral Kits ........................................................... 15 Using the Premium Docking Station ............................................... 16 Attaching the Shoulder Strap .......................................................... 18 4 Configuration ............................................ 19 4-1 4-2 4-3 COM Port Power ............................................................................... 19 Cash Drawer COM Port .................................................................... 20 USB over IP ....................................................................................... 21 viii 1 Item Checklist 1-1 Standard Items a. Tablet (11.6" or 13.3") b. Premium docking station c. 19V/120W or 19V/65W power adapter (standard, for premium docking station) d. Power cord e. 12V/36W power adapter (optional, for tablet only) 9 1-2 Optional Items a. MSR b. RFID c. Fingerprint d. iButton e. Shoulder strap 10 2 System View 2-1 Front View No. 1 2 3 4 5 6 7 8 Description Speaker Trigger key (middle) Power On/Off 2D scanner Trigger key (right) Full HD P-CAP multi-touch screen Mic Battery status indicator 11 2-2 Rear View No. 9 10 11 12 13 14 15 16 Description MSR/RFID/Fingerprint/iButton dummy cover Hand strap 5MP AF camera Trigger key (left) DC-in Should strap screw Docking connector USB type C 12 2-3 Specification System Motherboard F63 M276 F12 F33 F63 M278 F12 F33 CPU Whiskey Lake Celeron 4305U SNM758L-3308

(SnapDragon450) Elkhart Lake J6412 System memory DDR4 4GB LPDDR3 3GB DDR4 8GB Whiskey Lake Celeron 4305U DDR4 4GB Whiskey Lake Core i3-8145U DDR4 8GB SNM758L-3308

(SnapDragon450 Elkhart Lake J6412 LPDDR3 3GB DDR4 8GB Flash memory 128G eMMC 32G eMMC 128G eMMC 128G eMMC 32G eMMC 128G eMMC LCD Touch Panel LCD size Brightness Resolution Wireless Networking Wireless LAN + BLE Expansion I/O Ports USB type-C Mic DC POGO I/O port 2D scanner Extension Port Kits Full I/O Stand (Optional) 11.6"

13.3"

250 nits 1920*1080 802.11 a/b/g/n/ac 2.4G/5GHz, BLE*

1 (data transfer only) 1 1 16 Pin POGO 1 (Option : Honeywell 3601) 1 MSR / iButton / Fingerprint / RFID (either one) Full Function Full Function Front USB2.0 x 1 (Type A) Rear COM(RS232, 0V/5V/12V) x 2 LAN(RJ-45) x 1 USB2.0 x 0 (Type A) USB3.0 x 2 (Type A) Type C x 1 (data only 3.0) PUSB 24V x 1 PUSB 12V x 1 Cash drawer x 1 Front USB2.0 x 1 (Type A) Rear COM(RS232, 0V/5V/12V) x 2 LAN(RJ-45) x 1 USB2.0 x 0 (Type A) USB3.0 x 2 (Type A) Type C x 1 (data only 3.0) PUSB 24V x 1 PUSB 12V x 1 Cash drawer x 1 I/O ports Normal Normal Front USB2.0 x 1 (Type A) Rear COM(RS232, 0V/5V/12V) x 2 LAN(RJ-45) x 1 USB2.0 x 2 (Type A) USB3.0 x 0 (Type A) Type C x 1 (data only 2.0) PUSB 24V x 1 PUSB 12V x 1 Cash drawer x 1 Front USB2.0 x 1 (Type A) Rear COM(RS232, 0V/5V/12V) x 2 LAN(RJ-45) x 1 USB2.0 x 2 (Type A) USB3.0 x 0 (Type A) Type C x 1 (data only 2.0) PUSB 24V x 1 PUSB 12V x 1 Cash drawer x 1 13 System Motherboard F63 M276 F12 F33 F63 M278 F12 F33 Audio Speaker Control / Indicator Sensor LED indicator Camera (Optional) Rear camera Battery & Power Battery Hot swap battery Power adapter Peripherals Hand strap Certificate EMC & Safety Environment Operating temperature (none charging mode) Operating temperature

(charging mode) Storage temperature Humidity Size Dimension Weight OS Support Windows Android 1x 1W G-sensor 1 5MP 7268mAh, 3.85V (Max. Charging Power=27.98Wh) N/A Tablet only - 12V/36W 1 FCC Class B, CE Mark Class B, LVD, RF 0C ~ 40C (32F ~104 F) 0C ~ 35C (32 F ~ +95 F)

-10C ~ 45C (14F ~ 114F) 20% - 80% RH non-condensing 276 x 179 x 15.4 mm 312.5 x 200 x 15.4 mm 800g N/A 9 Windows10_20 19X64 N/A Windows 10_21H2X64 Windows10_20 19X64 N/A N/A 980g N/A 9 Windows 10_21H2X64 N/A

*Note: Disable DSS function 14 3 Getting Started 3-1 Power On/Off the System 1. Press the power button for 2 seconds to turn on the system and press it for 6 seconds to turn off the system. Note: For best touch performance, remove the protective plastic overlay from the touch screen by peeling it away from one of the corners. Be sure to use a soft pointing device or finger tip to avoid scratching the screen during normal use. 3-2 Installing the Peripheral Kits 1. Remove the dummy cover first. Remove the rubber pads (x2) and screws (x2)to release the top cover of the MSR module. 2. Connect the cable to the connector on the system side. Then position the MSR module over the system as shown and fasten with the screws (x2). Finally place the top cover of the MSR module back. NOTE: The variety of peripheral kits like RFID/Fingerprint and iButton all follow the same installation method. 15 3-3 Using the Premium Docking Station The premium docking station provides additional connectors and interfaces to support other devices and is also designed to allow the tablet to charge its battery via the dock. 1. To use the premium docking station, firstly connect the AC adapter to the DC-in input and connect the other end to the power outlet. Always plug in the AC adapter first to enable the locking/unlocking function.

* You can also charge the battery via the optional 36W power adapter. Plug in the AC adapter cable directly into the connector located on the bottom right of the tablet. Then plug the other end to the AC outlet. Attaching the tablet to the dock 2. After plugging in the AC adapter to the power outlet, align the rear of the tablet with the top of the docking station, and place the tablet onto the dock. The tablet automatically locks to the dock when attached. 16 Removing the tablet from the dock 3. Press the lock release button on the front of the docking station, and then lift the tablet off the dock. NOTE: The tablet will be locked again if it is not removed from the dock after pressing the release button in 10 seconds. The light on the docks lock release button indicates the locking status:

Blue - The tablet is locked Green - The tablet is unlocked and can be removed. Adjusting the tablet angle 4. The premium docking station offers adjustment of viewing angle. You can tilt and swivel the tablet to set it to angle you preferred. The tilt angle can be set between 0 and 17 and the swivel angle can be set to 180 in either direction. 17 3-4 Attaching the Shoulder Strap 1. Align and attach the shoulder strap to the tablet as shown and fasten the screws (x2) to secure it. 18 4 Configuration 4-1 COM Port Power 1. Double click P-2DK10_ConfigTool.exe to run the setup tool. 2. By default, both left and right COM port power are 0V. To change the default COM port power, select power and tap on Write COM Port Power to confirm.

* L/R COM port power can be set to different voltage individually, e.g., L:5V and R:12V. 19 4-2 Cash Drawer COM Port 1. Click on New Port COM and enter 7 in the column. 2. Tap on Set COM Port to confirm. 3. Double click P-2DK10_ConfigTool.exe to run the setup tool. 4. By default, both left and right COM port power are 0V. To change the default COM port power, select power and tap on Write COM Port Power to confirm. 20 5. You can check the current setup condition by tapping on Read.

* If the device is not connected or the setup process hasnt been completed yet, the Read /

Write column will be highlighted. 4-3 USB over IP The Premium Docking Station P-2DK10 is designed with the feature of USB over IP that offers a convenient way to extend and share a USB device over long distance, and it also works with multiple tablet-dock pairs. When the tablet docks on the premium docking station P-2DK10, it is connected via LAN and will be automatically switched to WLAN while releasing from the docking station. Prior to installing the USB client software, ensure that the WLAN is on the same network. 1. In the VirtualHere folder, double click Install.bat to install the software. Once it is completely installed, the program will launch automatically after you log into the computer.

* To remove the software, double click Uninstall.bat 21 2. Double click P-2DK10_ConfigTool.exe to run the setup tool. 3. Specify the MAC address of the server in your VirtualHere by clicking on Setp IP. The process may take up to 2~3 minutes showing the message Set IP....If all was done correctly, a popup window should appear indicating Set IP success!

4. The default setting of the system is Mode 1: POS Mode. To change the de-

fault mode, select Mode 2: All USB over IP and tap on Write USB over IP. 5. Restart your computer to confirm changes.

*Always dock your tablet on the premium docking station before changing the Mode.

** USB over IP Mode is not recommended for the use of mass storage devices. 22

Label & Location Host Model Name: M276EHL Back Side 100.00 mm 20.00 mm aiming FE CE X BK FLYTECH TECHNOLOGY CO.,LTD Address:No. 168, Sing-ai Rd.,Neihu District, Taipei City 11494, Taiwan This device complies with part 15 of the FCC rules: RoHS Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2)This device must accept any interference received, including interference that may cause undesired operation. Contains FCC ID:XHM-220808 P/N:3LEM27600100 MADE IN TAIWAN

FLYTECH Date: 2022-10-05 Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 Requesting Class II permissive change To Whom It May Concern:

The purpose of this letter is to request a Class II Permissive change for FCC ID: XHM-220808, Original grant date: 10/03/2022 The major change filed under this application is :

1. The subject approved module is being used in different host. (Tablet, Host Model:

M276EHL) SAR Test report is provided to demonstrate RF exposure Compliance. 3. The hardware design of this transmitter that may affect compliance is remained unchanged in this permissive change application. The RF parameters of this transmitter that may affect compliance are remained unchanged in this permissive change application. The security mechanism according to section Il of KDB 594280 DO2 is remained unchanged as it reported to the FCC at the initial certification. The master and client modes operate in each frequency band are same as it is in the original grant conditions. Sincerely,

(Signature) Aun Zan Company Name : FLYTECH TECHNOLOGY CO., LTD Address : No. 168, Sing-ai Rd., Neihu District, Taipei City, Taiwan Name and Job Title. : 9 Avin Zhan E-mail : avinchan@flytech.com.tw Tel. : 886-2-8791-4988 Extension:3461

FCC, Request for non-disclosure Date: 21-Nov-2018 RF_501, Issue 8 Page 1 of 1 Company Name: FLYTECH TECHNOLOGY CO., LTD Address: No. 168, Sing-ai Rd., Neihu District, Taipei City, Taiwan City: Taipei City Country: Taiwan To: Telefication B.V., Dept. FCC TCB Edisonstraat 12A 6902 PK ZEVENAAR The Netherlands Subject: Request for confidentiality FCC ID: XHM-220808 Reference number: ##HHHHt Dear FCC TCB, 1. Long-Term Confidentiality Pursuant to 47 CFR Section 0.459(a) & (b), we hereby requests non-disclosure and confidential treatment of the following materials submitted in support of FCC certification application:

CO Bill(s) of Material 1 Block Diagrams EJ Operational Description EX] Schematic Diagrams (J Tune-up Procedure Above materials contain secrets, proprietary and technical information, which would customarily be guarded from competitors under 47 CFR, section 0.457(d)(2). Disclosure or publication or any portion of this company confidential material to other parties could cause substantial competitive harm and provide unjustified benefits for competitors. 2. Short-Term Confidentiality (STC) Pursuant to Public Notice DA 04-1705 of the Commission's policy, in order to comply with the marketing regulations in 47 CFR 2.803 and the importation rules in 47 CFR 2.1204, applicant hereby requests Short-

Term Confidential treatment of the following materials (See notes below):

CJ Internal Photos [] Users Manual CL] Test Set-up Photos J External Photos Justification:

Date: 05 October 2022 Name and signature of applicant: Avin Zhan _ Vin > OM Notes:

1) A document or type of document can only have ONE type of confidentiality!

2) Short-Term confidentiality is in principle for 45 days from date of grant; it can be extended max 3 times (total time 180 days max.)!

The planned date should stated in the RF731 application form. 3) FCC must be informed when marketing begins earlier. 4) Release takes place automatically thus extension must be requested in time. Telefication does not remind you of this!

5) Request for extension or for release must be received by Telefication at least 7 days before date of actual marketing or before expiration of the STC period

RF_160, Issue 04 Declaration of Authorization We Name:

Address:

City:

Country:

Declare that:

FLYTECH Technology Co., Ltd. No. 168, Sing-Ai Rd., Neihu District 11494, Taipei City, Taiwan Taipei City Taiwan Name Representative of agent:

Agent Company name:

Address:

City:

Country Kevin Tsai (1) Compliance Certification Services Inc. No. 11. Wugong 6th Road New Taipei City Taiwan is authorized to apply for Certification of the following product(s):

Product description: Intel WiFi 6E AX210 Module Type designation: AX210NGW Trademark:

Intel Wi-Fi 6E AX210 Validity/ expiry date:

on our behalf. Date:

City:

Name:

Oct. 14, 2022 Taipei Avin Zhan (2) Function:

Manager Signature:

. Notes:

(1): Required for FCC application

(2): For FCC it must be the Grantee Code owner or the authorized agent.

FLYTECH Federal Communications Commission Date: 2022-09-13 Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Attention: Application Examiner/ Review Engineer Subject: Request to change in identification per section 2.933 of FCC rules Reference: FCC ID: XHM-220808 To Whom It May Concern:

This Change of Identification request applies for a new FCC ID as established in 47CFR 2.933(b) for a currently approved device. This application by FLYTECH TECHNOLOGY CO., LTD will establish a new FCC ID : XHM-220808 for purpose of marketing. The original grant to Intel Corporation with FCC ID: PD9AX210NG) will remain in effect. An authorization letter by Intel Corporation is attached. Per 2.933(b) 1. The original identification is PD9AX210NG 2. The original grant date is 02/18/2021 3. The equipment is elecirically identical. Only the model name, trade name, and FCC ID number are different. 4. The original test results are applicable and representative of this changed device. 5. Exterior photographs are included in this application. The following files are electronically submitted as attachments:

Cover Letter External Photos FCC ID label format and location Sincerely, Aura Drown Company Name : FLYTECH TECHNOLOGY CO., LTD Address : No. 168, Sing-ai Rd., Neihu District, Taipei City, Taiwan Name and Job Title. : Avin Zhan E-mail : avinchan@flytech.com.tw Tel. : 886-2-8791-4988 Extension:3461

Federal Communications Commission 7435 Oakland Mills Road Columbia, Maryland 21046 USA Re: Change of Identification Authorization, FCC ID: PD9AX210NG Date: August 29, 2022 To Whom It May Concern:

This letter grants authorization for representatives FLYTECH TECHNOLOGY CO., LTD to apply to the FCC for a change in identification as specified under 47CFR2.933 of the FCC rules. This authorization applies to the Intel Corporation, Intel WiFi 6E AX210, 802.11a/b/g/n/ac/ax+ BT M.2 form factor, model: AX210NGW, FCC ID: PD9AX210NG, approved on 10/19/2020(for 15b, BT, BLE, Wifi 2.4GHz and WiFi 5GHz) and 02/18/2021(for Wifi-6E). We are aware that FLYTECH TECHNOLOGY CO., LTD intends to market the above referenced product under their FCC ID: XHM-220808, part number AX210NGW. Sincerely, Steven C. Hackett Wireless Product Regulatory Engineer Mobile Wireless Group Intel Corporation Date: August 29, 2022 Intel Corporation S.A.S. 425 Rue de Goa Le Cargo B6 06600 Antibes France Tel. +33 (0)4 93 00 14 00 - Fax +33 (0)4 93 00 14 01 SAS au capital de 5 208 026,16 Euros RCS Nanterre 302 456 199 Siret 302 456 199 00256 - TVA FR54302456199

HIYTECH Federal Communications Commission Date: 2022-09-13 Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 SUBJECT: FCC Authorization Letter for FCC ID: XHM-220808 To Whom It May Concern:

We, the undersigned, hereby authorize following person to act as our agent on our behalf, to apply to the Federal Communications Commission on our equipment. Any and all acts carried out by the agent on our behalf shall have the same effect as acts of our own. Compliance Certification Service Address : No. 11. Wugong 6th Road, New Taipei City, Taiwan Name : Kevin Tsai Job Title : Manager e-mail : Kevin-Tw.Tsai@sgs.com This is to advise that we are in full compliance with the Anti- Drug Abuse Act. We, the applicant, are not subject to a denial of federal benefits pursuant to Section 5301 of the Anti-Drug Act of 1988, 21 USC853a, and no party to the application is subject to a denial of federal benefits pursuant to that section. Sincerely, Auru Z li Qn Company Name : FLYTECH TECHNOLOGY CO., LTD Address : No. 168, Sing-ai Rd., Neihu District, Taipei City, Taiwan Name and Job Title. : Avin Zhan E-mail : avinchan@flytech.com.tw Tel. : 886-2-8791-4988 Extension:3461