USER MANUAL
VERSION 1.0 October 2020
Panel PC
Hardware System
Copyright 2020
All Rights Reserved
Manual Version 1.0
The information contained in this document is subject to change without notice.
We make no warranty of any kind with regard to this material, including, but not limited
to, the implied warranties of merchantability and fitness for a particular purpose.
We shall not be liable for errors contained herein or for incidental or consequential
damages in connection with the furnishing, performance, or use of this material.
This document contains proprietary information that is protected by copyright. All rights
are reserved. No part of this document may be photocopied, reproduced or translated
to another language without the prior written consent of the manufacturer.
TRADEMARK
Intel®, Pentium® and MMX are registered trademarks of Intel® Corporation.
Microsoft® and Windows® are registered trademarks of Microsoft Corporation.
Other trademarks mentioned herein are the property of their respective owners.
Safety
IMPORTANT SAFETY INSTRUCTIONS
1. To disconnect the machine from the electrical power supply, turn off the power switch
and remove the power cord plug from the wall socket. The wall socket must be easily
accessible and in close proximity to the machine.
2. Read these instructions carefully. Save these instructions for future reference.
3. Follow all warnings and instructions marked on the product.
4. Do not use this product near water.
5. Do not place this product on an unstable cart, stand, or table. The product may fall,
causing serious damage to the product.
6. Slots and openings in the cabinet and the back or bottom are provided for ventilation
to ensure reliable operation of the product and to protect it from overheating. These
openings must not be blocked or covered. The openings should never be blocked by
placing the product on a bed, sofa, rug, or other similar surface. This product should
never be placed near or over a radiator or heat register or in a built-in installation
unless proper ventilation is provided.
7. This product should be operated from the type of power indicated on the marking label.
If you are not sure of the type of power available, consult your dealer or local power
company.
8. Do not allow anything to rest on the power cord. Do not locate this product where
persons will walk on the cord.
9. Never push objects of any kind into this product through cabinet slots as they may
(cid:87)(cid:82)(cid:88)(cid:70)(cid:75)(cid:3)(cid:71)(cid:68)(cid:81)(cid:74)(cid:72)(cid:85)(cid:82)(cid:88)(cid:86)(cid:3)(cid:89)(cid:82)(cid:79)(cid:87)(cid:68)(cid:74)(cid:72)(cid:3)(cid:83)(cid:82)(cid:76)(cid:81)(cid:87)(cid:86)(cid:3)(cid:82)(cid:85)(cid:3)(cid:86)(cid:75)(cid:82)(cid:85)(cid:87)(cid:3)(cid:82)(cid:88)(cid:87)(cid:3)(cid:83)(cid:68)(cid:85)(cid:87)(cid:86)(cid:3)(cid:87)(cid:75)(cid:68)(cid:87)(cid:3)(cid:70)(cid:82)(cid:88)(cid:79)(cid:71)(cid:3)(cid:85)(cid:72)(cid:86)(cid:88)(cid:79)(cid:87)(cid:3)(cid:76)(cid:81)(cid:3)(cid:68)(cid:3)(cid:192)(cid:85)(cid:72)(cid:3)(cid:82)(cid:85)(cid:3)(cid:72)(cid:79)(cid:72)(cid:70)(cid:87)(cid:85)(cid:76)(cid:70)(cid:3)
shock. Never spill liquid of any kind on the product.
10. To avoid the risk of electric shock, this equipment must only be connected to a supply
mains with protective earth.
11. (cid:49)(cid:82)(cid:3)(cid:80)(cid:82)(cid:71)(cid:76)(cid:192)(cid:70)(cid:68)(cid:87)(cid:76)(cid:82)(cid:81)(cid:3)(cid:82)(cid:73)(cid:3)(cid:87)(cid:75)(cid:76)(cid:86)(cid:3)(cid:72)(cid:84)(cid:88)(cid:76)(cid:83)(cid:80)(cid:72)(cid:81)(cid:87)(cid:3)(cid:76)(cid:86)(cid:3)(cid:68)(cid:79)(cid:79)(cid:82)(cid:90)(cid:72)(cid:71)(cid:17)
12. (cid:51)(cid:82)(cid:90)(cid:72)(cid:85)(cid:3)(cid:86)(cid:88)(cid:83)(cid:83)(cid:79)(cid:92)(cid:3)(cid:76)(cid:86)(cid:3)(cid:86)(cid:83)(cid:72)(cid:70)(cid:76)(cid:192)(cid:72)(cid:71)(cid:3)(cid:68)(cid:86)(cid:3)(cid:83)(cid:68)(cid:85)(cid:87)(cid:3)(cid:82)(cid:73)(cid:3)(cid:80)(cid:72)(cid:71)(cid:76)(cid:70)(cid:68)(cid:79)(cid:3)(cid:72)(cid:84)(cid:88)(cid:76)(cid:83)(cid:80)(cid:72)(cid:81)(cid:87)(cid:17)
ii
13. The medical PC can be cleaned in accordance with normal clinical cleaning practices,
including wiping with water or medical grade wipes, provided no substance containing
acids or cleaning alkali liquids is used.
14. Medical grade wipes must not contain more than 80% alcohol content measured
against the total content of the wipe.
15. Operator shall not contact patient simultaneously when in use with the medical
Sécurité
INSTRUCTIONS IMPORTANTES RELATIVES À LA SECURITE
1. Pour débrancher la machine de l’alimentation électrique, éteignez l’interrupteur
d’alimentation et retirez le cordon d’alimentation de la prise murale. La prise murale
doit être facilement accessible et à proximité de la machine.
2. Lisez attentivement ces instructions. Conservez ces instructions pour une référence
computer.
future.
3. Suivez tous les avertissements et les instructions indiquées sur le produit.
4. Ne pas utiliser ce produit à proximité de l’eau.
5. Ne pas placer ce produit sur un chariot, un support ou une table. Le produit peut
tomber,causant de graves dommages à l’appareil.
6. Les fentes et les ouvertures dans le boîtier, l’arrière ou le fond sont prévues pour
(cid:79)(cid:68)(cid:3)(cid:89)(cid:72)(cid:81)(cid:87)(cid:76)(cid:79)(cid:68)(cid:87)(cid:76)(cid:82)(cid:81)(cid:3)(cid:68)(cid:192)(cid:81)(cid:3)(cid:71)(cid:183)(cid:68)(cid:86)(cid:86)(cid:88)(cid:85)(cid:72)(cid:85)(cid:3)(cid:88)(cid:81)(cid:3)(cid:73)(cid:82)(cid:81)(cid:70)(cid:87)(cid:76)(cid:82)(cid:81)(cid:81)(cid:72)(cid:80)(cid:72)(cid:81)(cid:87)(cid:3)(cid:192)(cid:68)(cid:69)(cid:79)(cid:72)(cid:3)(cid:71)(cid:88)(cid:3)(cid:83)(cid:85)(cid:82)(cid:71)(cid:88)(cid:76)(cid:87)(cid:3)(cid:72)(cid:87)(cid:3)(cid:79)(cid:72)(cid:3)(cid:83)(cid:85)(cid:82)(cid:87)(cid:112)(cid:74)(cid:72)(cid:85)(cid:3)(cid:71)(cid:72)(cid:3)(cid:79)(cid:68)(cid:3)
surchauffe. Ces ouvertures ne doivent pas être obstruées ou couvertes. Les ouvertures
ne doivent jamais être bloquées en plaçant l’appareil sur un lit, un canapé, un tapis
ou autre surface similaire. Ce produit ne doit jamais être placé : à proximité ou sur un
radiateur, sur un registre de chaleur ou dans une installation intégrée à moins qu’une
ventilation adéquate soit prévue.
7. Ce produit doit être utilisé avec le type d’alimentation indiqué sur l’étiquette.Si
vous n’êtes pas sûr du type d’alimentation disponible, consultez votre revendeur ou
représentant local de l’entreprise.
8. Ne laissez rien reposer sur le cordon d’alimentation. Ne placez pas ce produit là oùdes
personnes peuvent marcher sur le cordon.
9. N’introduisez jamais d’objets d’aucune sorte dans ce produit à travers les fentes du
coffret car ils pourraient entrer en contact avec des points sous tension dangereux ou
court-circuiter des pièces. Ne renversez jamais de liquide d’aucune sorte sur le produit.
10. Pour éviter tout risque de choc électrique, cet équipement ne doit être branché que sur
une prise secteur avec terre.
11. (cid:36)(cid:88)(cid:70)(cid:88)(cid:81)(cid:72)(cid:3)(cid:80)(cid:82)(cid:71)(cid:76)(cid:192)(cid:70)(cid:68)(cid:87)(cid:76)(cid:82)(cid:81)(cid:3)(cid:71)(cid:72)(cid:3)(cid:70)(cid:72)(cid:87)(cid:3)(cid:112)(cid:84)(cid:88)(cid:76)(cid:83)(cid:72)(cid:80)(cid:72)(cid:81)(cid:87)(cid:3)(cid:81)(cid:183)(cid:72)(cid:86)(cid:87)(cid:3)(cid:68)(cid:88)(cid:87)(cid:82)(cid:85)(cid:76)(cid:86)(cid:112)(cid:72)(cid:17)
(cid:20)(cid:21)(cid:17)(cid:47)(cid:183)(cid:68)(cid:79)(cid:76)(cid:80)(cid:72)(cid:81)(cid:87)(cid:68)(cid:87)(cid:76)(cid:82)(cid:81)(cid:3)(cid:72)(cid:86)(cid:87)(cid:3)(cid:86)(cid:83)(cid:112)(cid:70)(cid:76)(cid:192)(cid:112)(cid:72)(cid:3)(cid:70)(cid:82)(cid:80)(cid:80)(cid:72)(cid:3)(cid:73)(cid:68)(cid:76)(cid:86)(cid:68)(cid:81)(cid:87)(cid:3)(cid:83)(cid:68)(cid:85)(cid:87)(cid:76)(cid:72)(cid:3)(cid:71)(cid:88)(cid:3)(cid:80)(cid:68)(cid:87)(cid:112)(cid:85)(cid:76)(cid:72)(cid:79)(cid:3)(cid:80)(cid:112)(cid:71)(cid:76)(cid:70)(cid:68)(cid:79)(cid:17)
13.L’ordinateur médical peut être nettoyé conformément aux pratiques de nettoyage
cliniques habituelles, notamment en essuyant avec de l'eau ou des lingettes de qualité
médicale, à condition qu'aucune substance contenant des acides ou des liquides de
nettoyage alcalins ne soient utilisés.
14.Les lingettes de qualité médicale ne doivent pas contenir plus de 80% d'alcool par
rapport au contenu total de la lingette.
15.L’opérateur ne doit pas toucher le patient lorsqu’il utilise l’ordinateur médical.
iii
This device complies with the requirements of the EEC directive 2014/30/EU with
(cid:85)(cid:72)(cid:74)(cid:68)(cid:85)(cid:71)(cid:3)(cid:87)(cid:82)(cid:3)(cid:180)(cid:40)(cid:79)(cid:72)(cid:70)(cid:87)(cid:85)(cid:82)(cid:80)(cid:68)(cid:74)(cid:81)(cid:72)(cid:87)(cid:76)(cid:70)(cid:3)(cid:70)(cid:82)(cid:80)(cid:83)(cid:68)(cid:87)(cid:76)(cid:69)(cid:76)(cid:79)(cid:76)(cid:87)(cid:92)(cid:181)(cid:3)(cid:68)(cid:81)(cid:71)(cid:3)(cid:21)(cid:19)(cid:20)(cid:23)(cid:18)(cid:22)(cid:24)(cid:18)(cid:40)(cid:56)(cid:3)(cid:180)(cid:47)(cid:82)(cid:90)(cid:3)(cid:57)(cid:82)(cid:79)(cid:87)(cid:68)(cid:74)(cid:72)(cid:3)(cid:39)(cid:76)(cid:85)(cid:72)(cid:70)(cid:87)(cid:76)(cid:89)(cid:72)(cid:181)(cid:17)
CE MARK
FCC
This device complies with part 15 of the FCC rules. Operation is subject to the following
two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may
cause undesired operation.
CAUTION ON LITHIUM BATTERIES
There is a danger of explosion if the battery is replaced incorrectly. Replace only
with the same or equivalent type recommended by the manufacturer. Discard used
batteries according to the manufacturer’s instructions.
Battery Caution
Risk of explosion if battery is replaced by an incorrectly type. Dispose of used battery
according to the local disposal instructions.
Safety Caution
Note: To comply with IEC60950-1 Clause 2.5 (limited power sources, L.P.S) related
(cid:79)(cid:72)(cid:74)(cid:76)(cid:86)(cid:79)(cid:68)(cid:87)(cid:76)(cid:82)(cid:81)(cid:15)(cid:3)(cid:83)(cid:72)(cid:85)(cid:76)(cid:83)(cid:75)(cid:72)(cid:85)(cid:68)(cid:79)(cid:86)(cid:3)(cid:86)(cid:75)(cid:68)(cid:79)(cid:79)(cid:3)(cid:69)(cid:72)(cid:3)(cid:23)(cid:17)(cid:26)(cid:17)(cid:22)(cid:17)(cid:21)(cid:3)(cid:180)(cid:48)(cid:68)(cid:87)(cid:72)(cid:85)(cid:76)(cid:68)(cid:79)(cid:86)(cid:3)(cid:73)(cid:82)(cid:85)(cid:3)(cid:192)(cid:85)(cid:72)(cid:3)(cid:72)(cid:81)(cid:70)(cid:79)(cid:82)(cid:86)(cid:88)(cid:85)(cid:72)(cid:181)(cid:3)(cid:3)(cid:3)(cid:3)(cid:3)(cid:70)(cid:82)(cid:80)(cid:83)(cid:79)(cid:76)(cid:68)(cid:81)(cid:87)(cid:17)
(cid:23)(cid:17)(cid:26)(cid:17)(cid:22)(cid:17)(cid:21)(cid:3)(cid:48)(cid:68)(cid:87)(cid:72)(cid:85)(cid:76)(cid:68)(cid:79)(cid:86)(cid:3)(cid:73)(cid:82)(cid:85)(cid:3)(cid:192)(cid:85)(cid:72)(cid:3)(cid:72)(cid:81)(cid:70)(cid:79)(cid:82)(cid:86)(cid:88)(cid:85)(cid:72)(cid:86)
For MOVABLE EQUIPMENT having a total mass not exceeding 18kg.the material of a
(cid:41)(cid:44)(cid:53)(cid:40)(cid:3)(cid:40)(cid:49)(cid:38)(cid:47)(cid:50)(cid:54)(cid:56)(cid:53)(cid:40)(cid:15)(cid:3)(cid:76)(cid:81)(cid:3)(cid:87)(cid:75)(cid:72)(cid:3)(cid:87)(cid:75)(cid:76)(cid:81)(cid:81)(cid:72)(cid:86)(cid:87)(cid:3)(cid:86)(cid:76)(cid:74)(cid:81)(cid:76)(cid:192)(cid:70)(cid:68)(cid:81)(cid:87)(cid:3)(cid:90)(cid:68)(cid:79)(cid:79)(cid:3)(cid:87)(cid:75)(cid:76)(cid:70)(cid:78)(cid:81)(cid:72)(cid:86)(cid:86)(cid:3)(cid:88)(cid:86)(cid:72)(cid:71)(cid:15)(cid:3)(cid:86)(cid:75)(cid:68)(cid:79)(cid:79)(cid:3)(cid:69)(cid:72)(cid:3)(cid:82)(cid:73)(cid:3)(cid:57)(cid:16)(cid:20)(cid:3)(cid:38)(cid:47)(cid:36)(cid:54)(cid:54)(cid:3)
MATERIAL or shall pass the test of Clause A.2.
For MOVABLE EQUIPMENT having a total mass exceeding 18kg and for all STATIONARY
EQUIPMENT, the material of a FIRE ENCLOSURE, in the thinnest significant wall
thickness used, shall be of 5VB CLASS MATERIAL or shall pass the test of Clause A.1
AVERTISSEMENT SUR LES BATTERIES AU LITHIUM
Il y a un danger d’explosion si la batterie n’est pas remplacée correctement.
Remplacez-la uniquement par une batterie identique ou de type équivalent
recommandée par le fabricant.les batteries usagées doivent être mises au rebut
conformément aux instructions du fabricant.
iv
Avertissement Batterie
Risque d’explosion si la batterie est remplacée par un élément incompatible.
Jetez les batteries usagées selon les instructions des dispositions locales .
Avertissement de sécurité
Remarque: Pour répondre à la norme IEC60950-1 alinéa 2.5 (sources d’énergie limitées,
LPS) liés la législation, les périphériques doivent être conforme 4.7.3.2 “Matériaux pour
enceinte coupe-feu»
4.7.3.2 “Matériaux pour équipements coupe-feu»
Pour les équipements mobiles ayant une masse totale n’excédant pas 18kg :
Les matériaux d’un équipement coupe-feu, dans l’épaisseur de paroi retenue la plus
(cid:86)(cid:76)(cid:74)(cid:81)(cid:76)(cid:192)(cid:70)(cid:68)(cid:87)(cid:76)(cid:89)(cid:72)(cid:80)(cid:72)(cid:81)(cid:87)(cid:3)(cid:80)(cid:76)(cid:81)(cid:70)(cid:72)(cid:15)(cid:3)(cid:71)(cid:82)(cid:76)(cid:89)(cid:72)(cid:81)(cid:87)(cid:3)(cid:114)(cid:87)(cid:85)(cid:72)(cid:3)(cid:71)(cid:72)(cid:86)(cid:3)(cid:80)(cid:68)(cid:87)(cid:112)(cid:85)(cid:76)(cid:72)(cid:79)(cid:86)(cid:3)(cid:71)(cid:72)(cid:3)(cid:38)(cid:47)(cid:36)(cid:54)(cid:54)(cid:40)(cid:3)(cid:57)(cid:16)(cid:20)(cid:3)(cid:82)(cid:88)(cid:3)(cid:71)(cid:82)(cid:76)(cid:89)(cid:72)(cid:81)(cid:87)(cid:3)(cid:83)(cid:68)(cid:86)(cid:86)(cid:72)(cid:85)(cid:3)(cid:79)(cid:72)(cid:3)
test de l’article A.2.
Pour équipements mobiles ayant une masse totale supérieure à 18 kg et pour tous les
équipements FIXES :
Les matériaux d’un équipement coupe-feu dans l’épaisseur de paroi retenue la plus
(cid:86)(cid:76)(cid:74)(cid:81)(cid:76)(cid:192)(cid:70)(cid:68)(cid:87)(cid:76)(cid:89)(cid:72)(cid:80)(cid:72)(cid:81)(cid:87)(cid:3)(cid:80)(cid:76)(cid:81)(cid:70)(cid:72)(cid:15)(cid:3)(cid:71)(cid:82)(cid:76)(cid:89)(cid:72)(cid:81)(cid:87)(cid:3)(cid:114)(cid:87)(cid:85)(cid:72)(cid:3)(cid:71)(cid:72)(cid:86)(cid:3)(cid:80)(cid:68)(cid:87)(cid:112)(cid:85)(cid:76)(cid:72)(cid:79)(cid:86)(cid:3)(cid:71)(cid:72)(cid:3)(cid:38)(cid:47)(cid:36)(cid:54)(cid:54)(cid:40)(cid:3)(cid:57)(cid:16)(cid:20)(cid:15)(cid:3)(cid:71)(cid:82)(cid:76)(cid:89)(cid:72)(cid:81)(cid:87)(cid:3)(cid:114)(cid:87)(cid:85)(cid:72)(cid:3)(cid:71)(cid:72)(cid:3)
classe Matériel 5VB ou doivent passer le test de l’article A.1
LEGISLATION AND WEEE SYMBOL
2012/19/EU Waste Electrical and Electronic Equipment Directive on the treatment,
collection, recycling and disposal of electric and electronic devices and their
components.
The crossed dust bin symbol on the device means that it should not be disposed of
with other household wastes at the end of its working life. Instead, the device should
be taken to the waste collection centers for activation of the treatment, collection,
recycling and disposal procedure.
To prevent possible harm to the environment or human health from uncontrolled waste
disposal, please separate this from other types of wastes and recycle it responsibly to
promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this product,
(cid:82)(cid:85)(cid:3)(cid:87)(cid:75)(cid:72)(cid:76)(cid:85)(cid:3)(cid:79)(cid:82)(cid:70)(cid:68)(cid:79)(cid:3)(cid:74)(cid:82)(cid:89)(cid:72)(cid:85)(cid:81)(cid:80)(cid:72)(cid:81)(cid:87)(cid:3)(cid:82)(cid:73)(cid:192)(cid:70)(cid:72)(cid:15)(cid:3)(cid:73)(cid:82)(cid:85)(cid:3)(cid:71)(cid:72)(cid:87)(cid:68)(cid:76)(cid:79)(cid:86)(cid:3)(cid:82)(cid:73)(cid:3)(cid:90)(cid:75)(cid:72)(cid:85)(cid:72)(cid:3)(cid:68)(cid:81)(cid:71)(cid:3)(cid:75)(cid:82)(cid:90)(cid:3)(cid:87)(cid:75)(cid:72)(cid:92)(cid:3)(cid:70)(cid:68)(cid:81)(cid:3)(cid:87)(cid:68)(cid:78)(cid:72)(cid:3)(cid:87)(cid:75)(cid:76)(cid:86)(cid:3)(cid:76)(cid:87)(cid:72)(cid:80)(cid:3)(cid:73)(cid:82)(cid:85)(cid:3)
environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of
the purchase contract.
This product should not be mixed with other commercial wastes for disposal.
v
Troubleshooting
For your own safety and that of your equipment, always take the following precautions.
Disconnect the power plug (by pulling the plug, not the cord), from your computer if any
of the following conditions exists:
• The power cord or plug becomes frayed or otherwise damaged.
• You spill something into the system.
• Your computer has been dropped or damaged.
• You suspect that your computer needs service or repair.
• You want to clean the computer or screen.
• You want to remove/install any parts.
Repair of the device may only be carried out by the manufacture.
We recommend that a service contract be obtained with supplier and
that all repairs also be carried out by them. Otherwise the correct
functioning of the device may be compromised.
vi
Revision History
Changes to the original user manual are listed below:
Revision
1.0
•
Initial release
Description
Date
October, 2020
vii
Table of Contents
1. Intended Use ................................. 1
2. Packing List .................................. 2
2-1. Standard Items ................................................................2
3. System View .................................. 3
3-1. Front & Side View ............................................................3
3-2. Rear & Bottom View ........................................................4
3-3. I/O View ...........................................................................4
3-4. Dimension ........................................................................5
4. Basic Operation ............................ 6
4-1. Powering On & Off ...........................................................6
4-2. Charging the Battery .......................................................7
4-3. Battery Level Indication ..................................................8
4-4. Battery Discharging Mode Flowchart .............................9
5. System Assembly ........................ 10
5-1. Removing the Cable Cover ............................................10
5-2. Replacing the Battery ....................................................10
5-3. Removing the Rear Cover ..............................................11
5-4. Replacing the RAM .........................................................11
5-5. Replacing the SSD .........................................................12
viii
(cid:25)(cid:17)(cid:3) (cid:54)(cid:83)(cid:72)(cid:70)(cid:76)(cid:192)(cid:70)(cid:68)(cid:87)(cid:76)(cid:82)(cid:81) ................................ 13
(cid:26)(cid:17)(cid:3) (cid:38)(cid:82)(cid:81)(cid:192)(cid:74)(cid:88)(cid:85)(cid:68)(cid:87)(cid:76)(cid:82)(cid:81) ............................... 15
7-1. D87U Motherboard Layout ............................................15
7-2. Connectors & Functions ................................................16
7-3. Jumper Setting ...............................................................17
ix
1. Intended Use
The Medical Computer is a computing device capable of storing, retrieving and sending data
electronically. This Medical Computer, including its user interface, RTC battery, PCB and
power supply, is intended to be fixed to a VESA wall mount in medical care environment.
This Medical Computer Hardware System must be operated by professional personnel (i.e.,
doctor, nurse...).
Application: Access to patient records / Hospital administration system / Bed management.
Cleaning method
• Turn off the system and disconnect the power cord and remove batteries before cleaning
the system.
• Use non-alcohol and non-abrasive liquid to clean the touch screen.
• Spread the cleaning liquid onto a sponge or cloth and then wipe the touch screen gently.
1
2. Packing List
2-1. Standard Items
a.
c.
b.
d.
a. System
b. Power adapter
c. Power cord
d. Battery
Note: Power cord will be supplied differently according to various region or country.
2
3. System View
3-1. Front & Side View
1
2
3
4
Item No.
1
2
3
4
Description
(cid:21)(cid:20)(cid:17)(cid:24)(cid:181)(cid:3)(cid:87)(cid:85)(cid:88)(cid:72)(cid:3)(cid:193)(cid:68)(cid:87)(cid:3)(cid:51)(cid:38)(cid:36)(cid:51)(cid:3)(cid:80)(cid:88)(cid:79)(cid:87)(cid:76)(cid:16)(cid:87)(cid:82)(cid:88)(cid:70)(cid:75)
batteries status
capacitive sensor touch function keys
(from left to right: Volume down /Volume up /Brightness darker /
Brightness lighter)
Power button
3
3-2. Rear & Bottom View
1
2
3
4
Item No.
1
2
3
4
Description
100 x 100 VESA mounting holes
75 x 75 VESA mounting holes
Battery door
Cable cover
3-3.
I/O View
a b c
d
e f
g h
Item No.
a
b
c
d
e
f
g
h
Description
COM
LAN
USB 1.1/ USB 1.0
USB 3.0
HDMI
DC in
COM
USB 1.1 (x2)
4
3-4. Dimension
533.13mm
m
m
4
6
4
2
3
.
59mm
5
4. Basic Operation
4-1. Powering On & Off
To activate the system, push 2-3 seconds and release the power button, the
display will come on in a few seconds. NOTE: The system must be plugged into
power adapter or battery charged before turning on for the first time.
To turn off the system, power off the device safely using software function that
(cid:180)(cid:86)(cid:75)(cid:88)(cid:87)(cid:86)(cid:3)(cid:71)(cid:82)(cid:90)(cid:81)(cid:3)(cid:70)(cid:82)(cid:80)(cid:83)(cid:88)(cid:87)(cid:72)(cid:85)(cid:181)(cid:3)(cid:83)(cid:85)(cid:82)(cid:89)(cid:76)(cid:71)(cid:72)(cid:71)(cid:3)(cid:76)(cid:81)(cid:3)(cid:87)(cid:75)(cid:72)(cid:3)(cid:82)(cid:83)(cid:72)(cid:85)(cid:68)(cid:87)(cid:76)(cid:81)(cid:74)(cid:3)(cid:86)(cid:92)(cid:86)(cid:87)(cid:72)(cid:80)(cid:17)
6
4-2. Charging the Battery
1. The system is equipped with 2 hot-
swappable batteries. The batteries
may be charged by connecting the
supplied power adapter directly to
the DC-in port on the system.
2. The system will charge in the order
of battery 1 to battery 2.
Status will show the capacity
of each battery.
NOTE: The battery status is detected
automatically by the system when the
battery cover is closed. Make sure
the battery cover is properly closed
before checking your battery status.
7
4-3. Battery Level Indication
Each battery provides an battery level indicator LED on the front of the system. The
signals charge status are as follows:
Battery
Battery full charged
Battery charging
Battery standby
Battery error
GREEN
GREEN blilnk slowly
GREEN
RED blink quickly
DC in Mode
Without battery
No signal
Battery / Power off
Battery full charged
Battery charging
Battery standby
GREEN
GREEN blilnk slowly
GREEN
Battery discharging ORANGE blink slowly
Battery standby
Battery lower 12%,
higher 6%
Battery 6%
Battery error
GREEN
RED blink slowly
RED
RED blink quickly
Without battery
Batery / Power off
No signal
No signal
Batery / Power off all batteries lower 6%
RED lights up for 6
seconds
Battery
Battery Mode
8
4-4. Battery Discharging Mode Flowchart
Battery discharging will be started from Battery 1 when system boot on battery
discharging mode.
Battery 1
Battery 2
When Battery 1 lock been released
Battery 2
capacitive is
higher than 6%
Battery 2
capacitive is
lower than 6%
Battery 2 slot
is empty
Start to drain from
Battery 2
Follow power
management
setting to do action
Follow power
management
setting to do action
If Battery 2 capacitive is lower than 3%, the system will be forced to shut down
9
5. System Assembly
5-1. Removing the Cable Cover
1. Place the system face down, make
sure not to scrath the screen.
2. Press and pull the cable cover
outwards to release it from the
system.
5-2. Replacing the Battery
1. Place the system face down, make
sure not to scrath the screen.
2. Remove the rubber pads (x6) and
screws (x6) to relesae the battery door.
3. Slide the latch down as shown to unlock.
4. Pull the plastic puller (see picture) to
release the battery out of the system.
10
5-3. Removing the Rear Cover
1. To open the rear cover of the system,
please follow the steps described in
Chapter 5-1 and 5-2 to remove the
cable cover and batteries first.
2. Remove the rubber pads (x9) and
loosen the screws (x10) of the rear
cover.
3. Gently lift the cover aside, the
power button at the bottom left
corner is connected to its cable
inside, be careful not to pull off
the cable while lifting the rear
cover.
5-4. Replacing the RAM
1. To replace the RAM module, please remove the cable cover, batteries, and
rear cover first (see Chapter 5-1, 5-2 and 5-3).
2. The motherboard is secured by the metal housing, remove the screw (x1) to
release the insulation cover located on top of the metal housing.
11
Installing a RAM moudle
Slide the memory module into the
memory slot anvd press down until the
ejector clips snaps in place.
3. Find the RAM module and flip the ejector clips outwards to remove the memory
module from the memory slot.
5-5. Replacing the SSD
1. Remove the cable cover, batteries, and rear cover first (see Chapter 5-1, 5-2 and
2. Remove the screw (x1) and slide the SSD module outwards to release it from the
5-3).
SATA cable.
3. Remove the screws (x2) that fix the SSD to the bracket.
12
6. (cid:54)(cid:83)(cid:72)(cid:70)(cid:76)(cid:192)(cid:70)(cid:68)(cid:87)(cid:76)(cid:82)(cid:81)
Model Name
Mainboard
CPU
System memory
LCD/Touch Panel
LCD size
Brightness
Maximal resolution
Touch screen type
Storage
Flash memory
Peripherals
RFID
Expansion
Mini PCIe socket
M.2
External I/O Ports
USB
HDMI
DC jack
Power switch
Isolation I/O Ports
COM
USB
LAN
Control/ Indicate
Power button
LED indicator
Audio
Speaker
Power
Wide range voltage
Power adapter
Battery
Battery
Communication
Wireless LAN + Bluetooth
Environment
(cid:38)(cid:72)(cid:85)(cid:87)(cid:76)(cid:192)(cid:70)(cid:68)(cid:87)(cid:76)(cid:82)(cid:81)
Operating temperature
13
K959 w/isolation
D87U
Intel SKYLAKE U CPU
i5-6300U 2.4GHz, LLC 3M
DDR4 2133 MHz (32GB Max) ; 2 Channel
21.5" LED LCD
250 nits
1920 x 1080
(cid:55)(cid:85)(cid:88)(cid:72)(cid:3)(cid:193)(cid:68)(cid:87)(cid:3)(cid:83)(cid:85)(cid:82)(cid:77)(cid:72)(cid:70)(cid:87)(cid:72)(cid:71)(cid:3)(cid:70)(cid:68)(cid:83)(cid:68)(cid:70)(cid:76)(cid:87)(cid:76)(cid:89)(cid:72)(cid:3)(cid:87)(cid:82)(cid:88)(cid:70)(cid:75)
SATA SSD Flash memory card
1
1 x M.2 slot half size ; Key ID- E (1 x USB & PCIe)
2 x DB-9
1 x USB1.0 / 3 x USB1.1
1(1x INTEL WG1211AT)
1 (w/LED indicator)
3 dual color LED indicators for 3 battery status
RFID (USB)
1 x USB3.0
1
1 (Lock type)
N/A (hidden)
1 x 2W
12V ~ 48V
DC 19V / 120W
2 x hot swappable battery with 160WHrs capacity
802.11 a/b/g/n/ac, 2.4G/5GHz, BT4.2
FCC/CE Class B, LVD
UL/EN60601-1
EN60601-1-2 4th edition
0°C ~ 35°C (32°F ~ 95°F)
Model Name
Mainboard
Storage temperature
Operating altitude range
Storage altitude range
Humidity
Dust & Water proof
Dimensions (W x D x H)
Weight (N.W.)
Mounting
K959 w/isolation
D87U
-20° ~ 60°C (-4°F ~ 140°F)
0-3000m
0-3000m
10% - 90% RH non-condensing
IP 65 (front panel) / IP X1 (back cover)
533 x 59 x 325 mm
7kg
VESA mount holes (M4) 75 x 75 mm /100 x 100 mm
*Recommended length of screw (L): Thickness (VESA mount) + 5mm
OS support
*(cid:55)(cid:75)(cid:76)(cid:86)(cid:3)(cid:86)(cid:83)(cid:72)(cid:70)(cid:76)(cid:192)(cid:70)(cid:68)(cid:87)(cid:76)(cid:82)(cid:81)(cid:3)(cid:76)(cid:86)(cid:3)(cid:86)(cid:88)(cid:69)(cid:77)(cid:72)(cid:70)(cid:87)(cid:3)(cid:87)(cid:82)(cid:3)(cid:70)(cid:75)(cid:68)(cid:81)(cid:74)(cid:72)(cid:3)(cid:90)(cid:76)(cid:87)(cid:75)(cid:82)(cid:88)(cid:87)(cid:3)(cid:83)(cid:85)(cid:76)(cid:82)(cid:85)(cid:3)(cid:81)(cid:82)(cid:87)(cid:76)(cid:70)(cid:72)(cid:17)
Windows IOT 10 (64-bit)
Manufactory information:
Factory: Flytech Technology Co., Ltd.
Address: NO.36 Huaya 3rd Rd., Guishan Township, Taoyuan County 33383, Taiwan
Tel No: 886-3-272-9688 Fax No: 886-3-272-9666
Adaptor Manufacturer: MEAN WELL ENTERPRISES CO., LTD.
Model: GSM120A20-R7B
14
7. (cid:38)(cid:82)(cid:81)(cid:192)(cid:74)(cid:88)(cid:85)(cid:68)(cid:87)(cid:76)(cid:82)(cid:81)
7-1. D87U Motherboard Layout
CN16
CN4
CN11
CN28
CN27
JP4
CN22
JP5
JP6
CN21
CN23
CN14
CN5
MINI-PCIE1
JP3
CN3
SKT2
DIMM_A1
DIMM_B1
SKT1
CN15
CN17
CN19
CN18
CN12
CN20
CN13
CN6
CN26
CN8
CN9
CN25
CN10
PCIE1
BAT1
JP2
CN2
FAN1
JP1
P
W
R
2
R
W
R
1
15
SW1
S
A
T
A
0
S
A
T
A
1
C
N
1
U
S
B
3
U
S
B
2
U
S
B
1
C
O
M
1
R
J
4
5
_
3
A
U
X
1
C
N
2
4
R
J
4
5
_
1
R
J
4
5
_
2
H
D
M
1
I
7-2. Connectors & Functions
Function
Connector
SATA power connector
CN1/2
EC debug port
CN3
Printer connector
CN4
M.2 WiFi socket
CN5
SDV connector
CN6
USB2.0 connector
CN8/9/10
COM4 connector
CN11
Inverter connector
CN12
eDP connector
CN13
Bedside connector
CN14
DP/HDMI Connector
CN15
DICOM Connector
CN16
DICOM for LVDS_VDD_EN
CN17
LVDS connector
CN18
SDR connector
CN19
ON/OFF & Power LED connector
CN20
Build in Speaker/MIC connector
CN21
Build in speaker(left)
CN22
Build in speaker(right)
CN23
Audio jack
CN24
Charger board power connector
CN25
Charger board function connector
CN26
LAN2 LED connector for by pass no isolator
CN27/28
PCIE X4 slot connector
PCIE1
FAN connector
FAN1
HDMI connector
HDMI
MIC in jack
AUX1
DC Jack
PWR1/PWR2
Cash drawer connector
RJ11_1
LAN1 connector
RJ45_1
COM1/COM2_RS232/422/485
RJ45_2
RJ45_3
LAN2 connector
DiMM_A1 / DIMM_B1 DDR4 SO-DIMM
SATA0/SATA1
BAT1
USB1/USB2
USB3
COM1
SW1
MINI_PCIE1
JP1
JP2
JP3
JP4/5
JP6
SATA connector
Battery socket
USB3.0
Isolator USB connector
CRT connector
Power button
Mini PCIe WiFi socket
LCD ID setting
Clear CMOS
Hareware reset
isolator USB speed select
Audio Mono setting
16
7-3.
Jumper Setting
Isolator USB (up port) speed select
Isolator USB (down port) speed select
JP4
1 3
4
2
1 3
4
2
JP4
1 3
4
2
1 3
2
4
JP5
1 3
4
2
1 3
4
2
JP5
1 3
4
2
1 3
2
4
Function
USB1.0
(cid:634)(cid:3)(cid:56)(cid:54)(cid:37)(cid:20)(cid:17)(cid:20)
Function
(cid:3)(cid:634)(cid:3)(cid:56)(cid:54)(cid:37)(cid:20)(cid:17)(cid:19)
USB1.1
Mono
(cid:634)(cid:3)(cid:54)(cid:87)(cid:68)(cid:81)(cid:71)(cid:68)(cid:85)(cid:71)
Audio Mono select
Function
JP6
1
2
1
2
LCD ID Setting
Resolution
LVDS
Bits
Channel
Output Interface
JP1
1920 x 1080
24
Dual
LVDS Panel
1 3
4
2
5
6
7
8
9
10
1
2
1
Jumper open 2
(cid:3)(cid:3)(cid:45)(cid:88)(cid:80)(cid:83)(cid:72)(cid:85)(cid:3)(cid:86)(cid:75)(cid:82)(cid:85)(cid:87)(cid:3)(cid:3)(cid:3)(cid:3)(cid:3)(cid:3)(cid:634)(cid:3)(cid:32)(cid:3)(cid:48)(cid:68)(cid:81)(cid:88)(cid:73)(cid:68)(cid:70)(cid:87)(cid:88)(cid:85)(cid:72)(cid:85)(cid:3)(cid:39)(cid:72)(cid:73)(cid:68)(cid:88)(cid:79)(cid:87)(cid:3)(cid:54)(cid:72)(cid:87)(cid:87)(cid:76)(cid:81)(cid:74)
17
Isolation Board Layout
JP1
CN1
CN3
CN2
Function
USB1.0
(cid:634)(cid:3)(cid:56)(cid:54)(cid:37)(cid:20)(cid:17)(cid:20)
USB1.0
(cid:634)(cid:3)(cid:56)(cid:54)(cid:37)(cid:20)(cid:17)(cid:20)
JP2
USB1
COM1
Isolator USB (up port) speed select (on isolation board)
Isolator USB (down port) speed select (on isolation board)
JP2
Function
JP1
JP1
1 3
4
2
1 3
4
2
1 3
4
2
1 3
4
2
JP2
1 3
4
2
1 3
4
2
1 3
4
2
1 3
4
2
(cid:3)(cid:3)(cid:3)(cid:3)(cid:3)(cid:3)(cid:3)(cid:3)(cid:3)(cid:3)(cid:3)(cid:3)(cid:3)(cid:3)(cid:3)(cid:3)(cid:3)(cid:56)(cid:54)(cid:37)(cid:20)(cid:17)(cid:20)(cid:3)(cid:70)(cid:68)(cid:81)(cid:3)(cid:82)(cid:81)(cid:79)(cid:92)(cid:3)(cid:75)(cid:68)(cid:89)(cid:72)(cid:3)(cid:81)(cid:82)(cid:85)(cid:80)(cid:68)(cid:79)(cid:3)(cid:73)(cid:88)(cid:81)(cid:70)(cid:87)(cid:76)(cid:82)(cid:81)(cid:86)(cid:3)(cid:73)(cid:82)(cid:85)(cid:3)(cid:87)(cid:75)(cid:72)(cid:3)(cid:73)(cid:82)(cid:79)(cid:79)(cid:82)(cid:90)(cid:76)(cid:81)(cid:74)(cid:3)(cid:86)(cid:83)(cid:72)(cid:70)(cid:76)(cid:192)(cid:70)(cid:68)(cid:87)(cid:76)(cid:82)(cid:81)(cid:86)(cid:29)
• USB1.1
• USB2.0 (reduction of speed)
• USB3.0 (reduction of speed))
The USB setting for Keyboard:
USB1.0 Keyboard -> Setting USB1.0
USB2.0 Keyboard -> Setting USB1.1
1
2
1
Jumper open 2
(cid:3)(cid:3)(cid:45)(cid:88)(cid:80)(cid:83)(cid:72)(cid:85)(cid:3)(cid:86)(cid:75)(cid:82)(cid:85)(cid:87)(cid:3)(cid:3)(cid:3)(cid:3)(cid:3)(cid:3)(cid:634)(cid:3)(cid:32)(cid:3)(cid:48)(cid:68)(cid:81)(cid:88)(cid:73)(cid:68)(cid:70)(cid:87)(cid:88)(cid:85)(cid:72)(cid:85)(cid:3)(cid:39)(cid:72)(cid:73)(cid:68)(cid:88)(cid:79)(cid:87)(cid:3)(cid:54)(cid:72)(cid:87)(cid:87)(cid:76)(cid:81)(cid:74)
18