FCC ID: 2AL7F-Y28 Smart bird feeder

V1.0 Whats in the box Bird feeder Bracket Anchors*4 Micro-usb Charging cable Screws for wood*4 screw washers*4 Screws for wall*4 Pin Bird feeder structure Bird feeder cover Bracket Solar panel Camera Bird Stand Hummingbird feeder

- 1 -

Camera structure Microphone Light sensor Camera bracket Speaker Power ON/OFF Infrared led Lens PIR mounng sensor TF card slot LED indicator light Charging port Sync/Reset Camera Specicaon Y28 Product model 2W Watts(max.) Power Consumption Standby current Battery life Pixel Viewing angle Night visual range Wireless connection Anti-flicker

<500uA 4-6 months 2 megapixel 1080P 170 8m(max) 2.4G 50HZ 60HZ Operating temperature

-20.5~48 Operating humidity 10%~95% non-condensing

- 2 -

Battery capacity Maximum capacity of 4500mAh 128G memory card solar charging Power supply 5V/200mAh DC 5V2A STATUS LED 1.Power on: Blue light on 2.Charging: Red light on 3.Connecng to network: Blue light ashing 4.Connected to network successfully: Blue light on constantly 5.Fully charged: Red light o Read Before Installaon:

1.Please keep the bird feeder and all accessories out of the reach of children and pets. and seng it up. 2.Ensure that the camera has been fully charged before connecng 3.Operang temperature range: -5F to -120F (-20 to 48.5). 4.Operang relave humidity range: 10% to 95%. 5.Do not expose the camera lens to direct sunlight. 6.The camera has an IP65 waterproof rang, and can operate normally in rainy and snowy weather condions, but should not be submerged in water. NOTE:

1.The bird feeder supports 2.4G WiFi networks. 2.When connecng to WiFi for setup and using the camera, try to stay within range of a strong WiFi signal to avoid weak signal issues that may aect camera setup and use. 3.Avoid placing the device near furniture or other products that generate electromagnec interference, such as microwaves.

- 3 -

Installing a bird feeder: wall and wood surface installaon I. Wall Installaon:

1.Begin by marking the locaons for the screw holes on the wall according to the bracket holes, then drill four holes using the drill bit (Note: the narrow end of the bracket hook should face upwards). 2.Place four anchors into the drilled holes, then place the larger wall screws into the bracket's grooves and use the iron wrench provided with the product to ghten the screws and secure the bracket. 3.Use two iron wrenches to ghten the screws on the adjustable parts of the bracket up and down to adjust the bird feeder's direcon. When the bird feeder's direcon is set, ghten the screws as much as possible to support the bird feeder and prevent it from lng. 4.Adjust the ghtness of the screws as needed and x the bird feeder bracket in the le and right direcons.

- 4 -

5.Align the slot on the back of the bird feeder with the card holder on the bracket, and insert it to complete the installaon. If needed, you can ghten the small screw next to the card holder to secure the connecon between the bird feeder and the bracket. II. Wood surface installaon:

1.Start by marking the four screw posions on the wood surface according to the small screw holes on the bracket base (Note: the narrow end of the bracket hook should face upwards). Then, insert the screw washers onto the screws and use a screwdriver or electric screwdriver to secure the bracket to the wood surface.

- 5 -

2.Use the two wrenches to ghten the screws on the moving parts of the bracket to adjust the up and down direcon of the bird feeder. Once the direcon is set, rmly ghten the screws to support the bird feeder and prevent lng. 3.Depending on the required ghtness, adjust the screws to x the bird feeder bracket in the le and right direcons. 4.Align the slot on the back of the bird feeder with the card holder on the bracket, and insert it to complete the installaon. If needed, you can ghten the small screw next to the card holder to secure the connecon between the bird feeder and the bracket.

- 6 -

Installing the app Download the iWFCam from APP Store or Google Play.The iWFCam App connects your camera to your Android or iOS mobile device ensuring you are always connected to what maers most. To get the App, search for "iWFCamin the Google Play or App Store and download it.You can also use your mobile to scan the QR-Code to download the "iWFCam" App. 1.Aer opening the app and entering itPlease click"agree"

[user agreement and privacy policy] and allow the iWFCam app to access your pictures and video, or it may lead to fail to connect to wi.

- 7 -

2.Click on the '+' to add a device."

3.Click 'OK' to proceed to the next step."

4.Click 'ALLOW ONLY WHILE IN USE' to proceed to the next step."

- 8 -

5.Click 'ALLOW' to proceed to the next step."

6.Select the rst opon "Setup Device WIFI connecon"

and proceed to the next step. 7.If the camera blue light is ashing slowly, it means that the camera is ready to be connected to the network. Click "Light is slow ashing(1 sec)->Next". 8.Click "I want to connect my phone to the AP now" to proceed to the next step.

- 9 -

9.Select the WiFi hotspot with the prex "KCKJA**********". 10.Click "CONNECT" to connect and once the connecon is successful, click the arrow () on the top le corner to return to the app interface. Note: The Android system will prompt you with the following content. Please select "CONNECT" to proceed.

- 10 -

11.Select your home WiFi (if not displayed, please click the double arrow on the right to refresh), enter the WiFi password

(you can click the icon on the right to show the input content to ensure that the password is entered correctly), and click

"Start conguring WIFI" and then "OK" to enter the camera's connecon sengs. 12.When the camera enters the network conguraon seng, there will be a "beep" sound. Aer waing for a while, there will be two "beep beep" sounds, indicang that the camera has been successfully set up for networking. Click "OK" to proceed.

- 11 -

13.Once the camera is set up successfully, a green "Onling" icon will appear. Then click the middle triangle icon in the camera to refresh the camera image. 14.Aer clicking refresh, a popup window will appear. Please select "SKIP". The camera will display the image. "CHANGE" is for password modicaon, the camera's default password is: 8888. 15.When the camera image appears, the setup is successful.

- 12 -

Camera interface features:

1 2 3 4 5 8 7 6 9 1.Display of four devices on one screen 2.Mul-device display 3.Device search 4.QR code scanning 5.Device addion 6.Live video 7.Video recording and photo storage folder 8.Alarm push nocaons 9.App informaon

- 13 -

3 2 1 7 8 10 4 5 6 9 11 12 1.Brightness 2.Contrast 3.Saturaon 4.Image vercal adjustment 5.Night vision light control 6.Landscape switch 7.Speaker 8.Microphone 9.Deterrent ringtone 10.Screen recording 11.Camera capture 12.AI recognion

- 14 -

Quesons and Answers:

1.What to do if the connecon setup fails a. Please ensure that the camera is within a strong WiFi network coverage area (recommended around 10 meters or 33 feet). b. Verify if the WiFi name and password are correct. If not, press and hold the "RESET" buon for 6 seconds unl you hear a "beep"

sound to reset the camera. Wait for approximately 20 seconds for the camera to reboot and emit the "beep" prompt sound before aempng the connecon setup again. 2.What to do if the bird recognion fails and displays a 0% similarity?

If the bird is not clear or the angle, clarity, or completeness of the bird's physical features is poor, the camera might not be able to recognize the bird accurately or at all. Try to recognize the bird again when it appears from a more suitable angle and with clearer features. If the bird sll cannot be recognized or is misidened, it could be because the database is missing informaon on that parcular bird species. Please send us the image or name of the bird, and we will add its informaon to our database and improve it. 3.How to get more informaon about the recognized bird?

Aer the bird is successfully recognized, click "More Details" in the boom le corner to view the bird's encyclopedia informaon. If you encounter any issues while using the smart bird feeder, please feel free to contact us via email. We will provide you with comprehensive aer-sales service!

- 15 -

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

C5266091_X24_Ed.2 Attestation Statements that prohibit equipment authorization TO:

Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 The Commission adopted rules for covered telecommunications equipment and video surveillance equipment produced by entities identified on the Commissions Covered List1, which is periodically updated. See the Covered List for more details. This Attestation Statement is to confirm that we follow the Section 2.911(d)(5)(i)-(ii) Applicant Company name: Focus Industrial (HongKong) Development CO.,LIMITED Grantee code: 2AL7F FCC ID:

FRN: 0026541342 Contact Name:

Tony hu Address: Room 803, Chevalier House, 45-51 Chatham Road South, Tsim Sha Tsui, Kowloon , Hong Kong Telephone: 13923806817 E-mail: tonyhu@focusfirebox.com Fax: 0755-29963133 2AL7F-Y28 i. ii.

[Focus Industrial (HongKong) Development CO.,LIMITED] (the applicant) certifies that the equipment for which authorization is sought is not covered equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. The applicant must sign this certification.

[Focus Industrial (HongKong) Development CO.,LIMITED] (the applicant) certifies that, as of the date of the filing of the application, the applicant [is not] (as a specifically named entity or any of its subsidiaries or affiliates) identified on the Covered List as an entity producing covered equipment. The applicant must sign this certification.

[Focus Industrial (HongKong) Development CO.,LIMITED] (the applicant) certifies that, as of the date of the filing of the application, the applicant [ is not] identified on the Covered List as an entity producing coveredequipment . Date: 2024/04/02 Applicants Name: Tony hu Title: Manager Signature 1 The Commissions Covered List is published by the Public Safety and Homeland Security Bureau and posted on the Commissions website. This Covered List, which is periodically updated, identifies particular equipment, produced by particular entities, that constitutes covered equipment. https://www.fcc.gov/supplychain/coveredlist 1/1

Shenzhen Kechuang Technology Co., Ltd. Date: 2024-04-02 Federal Communications Commission To Whom It May Concern:

The letter grants authorization for representative of _ Focus Industrial (HongKong) Development CO.,LIMITED __ to apply the FCC for a change in identification. This authorization applies to _ Shenzhen Kechuang Technology Co., Ltd. _, FCC ID: _ 2BB2F-Y28A _, granted on _ 07/19/2023 __. The equipment is electrically identical. The only applicant name address, model name and FCC ID differ. The original test results, technical information and relevant documents continue to be representative of and applicable to the changed equipment. Should there be any question, please feel free to contact us. Sincerely, Clients name / title : Jason lu / Manager Contact information / address: 8/F,Building C10,Fuyuan Mill Town,Jiuwei Village,Xixiang Street,Baoan District Page 1 of 1

C5266091_X4_Ed.1 Focus Industrial (HongKong) Development CO.,LIMITED Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 2024-04-02 Subject:

Request for 2.933 Change in identification of equipment Reference:

FCC ID: 2BB2F-Y28A (new ID: 2AL7F-Y28) Gentlemen,

(Focus Industrial (HongKong) Development CO.,LIMITED) requests a Change in Identification for a currently approved device. This application will establish a new FCC ID for purpose of marketing. The original Grant for (Shenzhen Kechuang Technology Co., Ltd.), under FCC ID: 2BB2F-Y28A with a Grant Date of (07/19/2023) will remain in effect. An authorization letter from the original Grantee is attached. We attest that the equipment is electrically identical. Only applicant name address, model name and FCC ID differ. The original test results are applicable and continue to be representative of this device. The following files are provided as attachments:

Cover letter giving permission from original Applicant for Change in ID External photos showing no physical changes to this device New FCC identification label and its location. Thanks and Best Regards, Signature:

Tony hu Focus Industrial (HongKong) Development CO.,LIMITED Room 803, Chevalier House, 45-51 Chatham Road South, Tsim Sha Tsui, Kowloon , Hong Kong

(New Applicant phone) 13923806817

(New Applicant Email) tonyhu@focusfirebox.com 1/1

Focus Industrial (HongKong) Development CO.,LIMITED Product Similarity Declaration Company: Focus Industrial (HongKong) Development CO.,LIMITED Address: Room 803, Chevalier House, 45-51 Chatham Road South, Tsim Sha Tsui, Kowloon , Hong Kong Product Name: Smart bird feeder Model Number: Y28 Y28-A,Y28-B,Y29,Y29-A,Y29-B FCC Identifier: 2AL7F-Y28 We (Focus Industrial (HongKong) Development CO.,LIMITED) hereby state that all the models are electrical identical including the same software parameter and hardware design (i.e., circuit design, PCB Layout, RF module/circuit, antenna type(s) and antenna location, components on PCB, etc.,), same mechanical structure and design (including product enclosure, materials, etc.,), the only difference is the model name and appearance color. Clients signature Name: Tony hu Title: Manager Date: 2024-04-02 Signature of applicant:

Focus Industrial (HongKong) Development CO.,LIMITED Letter of Authorization Company: Focus Industrial (HongKong) Development CO.,LIMITED Address: Room 803, Chevalier House, 45-51 Chatham Road South, Tsim Sha Tsui, Kowloon , Hong Kong Product Name: Smart bird feeder Model Number: Y28 Y28-A,Y28-B,Y29,Y29-A,Y29-B FCC Identifier: 2AL7F-Y28 We authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, to act on our behalf on all matters concerning the above named equipment. Any individual within LGAI Technological Center S.A. is authorized to act on our behalf and take action on the application. We declare that authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, is allowed to forward all information related to the approval project to the Federal Communication Commission and to discuss any issues concerning the approval application. Any and all acts carried out by LGAI Technological Center S.A. on our behalf shall have the same effect as acts of our own. Name: Tony hu Title: Manager Date: 2024-04-02 Signature of applicant:

1/1

US Agent for Service of Process LETTER OF ATTESTATION 2AL7F-Y28 Jimmychen 001-323-51 04660 ugk-lvm@hotmail.com TO:

Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 US Agent for Service of Process:

Company Name: UGK-LVMUNITEDINC FRN: 0033476375 Contact Name:

Address: 6547NAcademyBlvd#2266,ColoradoSprings,CO80918 Telephone No:

Email:

Applicant:

Company name: Focus Industrial (HongKong) Development CO.,LIMITED Grantee code: 2AL7F FCC ID:

FRN: 0026541342 Contact Name:

Tony hu Address: Room 803, Chevalier House, 45-51 Chatham Road South, Tsim Sha Tsui, Kowloon , Hong Kong Telephone: 13923806817

[Focus Industrial (HongKong) Development CO.,LIMITED] certifies that, as of the date of this filing of the application with the TCB, [UGK-LVMUNITEDINC] is our designated US agent for service of process for the above referenced FCC ID. [Focus Industrial

(HongKong) Development CO.,LIMITED] accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any commission related proceeding involving equipment. [UGK-

LVMUNITEDINC] accepts, as of the date of the filing of the application, the obligation of the designated US agent for service of process for the above reference FCC ID. The US Agent for Service of Process is aware of and agrees to comply with the requirements outlined in the FCC Equipment Authorization Program, Report and Order FCC 22-84, and clause 2.911. The Applicant is aware of and agrees to comply with the requirements outlined in the FCC Equipment Authorization Program, Report and Order FCC 22-84, and clause 2.911. Date: 2024/04/02 E-mail: tonyhu@focusfirebox.com Fax: 0755-29963133 Applicants Name: Tony hu Title: Manager US Agent for Service of Processs Name:

Jimmychen Title: Manager Signature Signature 1/1