FCC ID: 2A9OS-YW-0199TX wireless backup camera

Congratulations on purchasing our Backup Camera System!

USER MANUAL Digital Wireless Camera System SPLIT VIEW FOR ( 2) CAMERA IN NO EVENT SHALL SELLER OR MANUFACTURER BE LIABLE FOR ANY DIRECT OR CONSEQUENTIAL DAMAGES OF ANY NATURE, OR LOSSES OR EXPENSES RESULTING FROM ANY DEFECTIVE PRODUCT OR THE USE OF ANY PRODUCT. We recommend doing a benchmark test before installaon to ensure that all components are working properly. If you have quesons about this product, contact :

FORSAFE CO., LTD info@51forsafe.com www.51forsafe.com YW-0199TX Normally you do not need to pair the camera and monitor, we defaulted and paired them well to the rst channel before delivery. What you need to do are as follow:

1. Find out the installaon place of the camera and the power of reversing light( or ACC). 2. Install the monitor to a suitable place and connect it to the cigaree lighter. Contact us by email "info@51forsafe.com" or via our web: www.51forsafe.com "Contact Us"

may any quesons during operaon. Package contents Wireless camera x 1 5" wireless monitor x 1 Mount Bracket x 1 Antenna x 1 Screw Kit for Camera Installaon x 1 Installaon Electric shock or product malfuncon may occur if this product is installed incorrectly. Use this product within the voltage range specied. Failure to do so can cause electronic shock or product malfuncon. Take special care when cleaning the monitor, no wet hands touch during installaon. Make sure to rmly ax the product before use. If smoke or a burning smell is detected, disconnect the system immediately. Where the power cable may touch a metal case, cover the cable with fricon tape. A short circuit or disconnected wire may cause a re. While installing the System be careful with the wire posioning in order to avoid wire damage. Do not watch movies or operate the monitor while driving; as it may cause an accident. Do not install the monitor where it may obstruct drivers view or obstruct an air bag device. Dropping the unit may cause possible mechanical failure. Do not hard press on the camera lens. Do not crush or damage the power cable. Do not use the device during a lightning storm. Operang Precauons 1. The device may be powered by a 12/32 volt baery or the vehicle's electrical system. 2. Make sure all cables are connected properly. Improper cable connecons may damage the monitor. Remove the power cable connecons when not using the device. Monitor Installaon Upward locking bracket FAQ 1. Is the signal between the camera and the receiver encrypted?

Yes. 2. How many cameras does the system support?

2 cameras. 3. Why does the frame rate somemes drop when I am driving?

When driving the signal recepon might drop somemes. This occurs as the signal to the receiver is constantly transmied from dierent angles. This is considered normal when transming wirelessly. 4. Is the camera water resistant?

The camera is Ip69k classed. This means that the camera is well protected from both dust and humidity. It can be placed outside and can be cleaned using a pressure washer. 5. Can I hear sound from the camera?

No, the camera does not have a microphone. 6. I am using the camera for reversing, how do I mirror the image?

Please see the instrucons in the Operaon secon. 7. What do I do if I have bad recepon on the LCD-monitor?

Start by reading through the troubleshoong. If troubleshoong doesnt help, welcome to contact us: info@51forsafe.com 8. Will the camera break at very low temperatures?

No, at very low temperatures the picture might tone red. At extremely low temperatures the camera might turn o. However, when the temperature gets higher again the camera will regain its funconality. 1 6 Picture-Image Sengs PAIRING PICTURE MIR-FLIP SYSTEM CH1 BRIGHTNESS CONTRAST HUE 6 6 6 The image can be modied to the driver's specicaons. Easily adjust the Brightness, Contrast, and Color to create the opmal brightness. 1) Press Menu 2) Press / & OK to Select Picture 3) Press OK & / to adjust picture image sengs Mir-ip Screen Rotaon Sengs CH1 PAIRING PICTURE MIR-FLIP SYSTEM NORMAL MIRROR FLIP MIR-FLIP Rotaon Opons (Vercal + Horizontal) There are many advantages to rotang a screen vercally or horizontally. Dierent views include :

Normal Standard Display Display in classic view Mirror Horizontal Reverse Display ipped horizontally Flip Vercal Reverse Display ipped vercally Mir Flip Hand V Revers Display ipped vercally + horizontally System - Sengs PAIRING PICTURE MIR-FLIP SYSTEM CH1 ENGLISH 5 20 LANGUAGE DELAYTIME 45 SCANTIME AUTOSCAN ON OFF 1. Press Menu , ChooseSYSTEM Press OK 2. Press , to adjust 3. Press OK to select Language: Language Selecon Delayme: Interval Time when reversing camera displays Scanme: Interval me when autoscan is on Autoscan: Auto displays CH1 & CH2 on/o Autoscan means system displays CH1 & CH2 by turns 5 Technical Specicaon Monitor 4.3" LED Digital Panel PAL/NTSC auto 480 x 3(RGB) x 272 400cd/m2 NO 0.077(W) x 0.231(H)mm 500:1 16:9 Top: 50, Boom 70, L/R 70 Monitor Panel Size Video System Resoluon Brightness Contrast Rao Screen Mode Field of View Audio Dot Pitch Acve Area 110.000(W) x 62.832(H)mm Power Input DC 10V-32V Operang Temperature Frequency Transmission Type Video Input 2 Channel Video Source 1vp-p75 Pairing About 4W Power Cosumpon Transmission Distance 328 Display Mode Single / Autoscan / Split View 2412-2462 MHz Digital Wireless CH1 Camera Paired

-4F to approx. 176F F=2.7 mm 1/4' CMOS 512x492 700 TV LINES 0.1 LUX 260mA 1/4 inch Camera Sensor Eecve Pixel Array Sync. System Minuminaon Working Current Opcal Format Lens Viewing Angle Waterproof Rang Power Consumpon Power Input DC12 -32V Operang Temperature Frequency Transmission Type Transmission Distance S/N Rao Digital Wireless 328 More than 48dB 170 IP69K About 2.5W (IR on) 2400-2483.5 MHz

-4F to approx. 176F 2 Wiring The System Monitor Operaon 1 2 3 4 5 Connect to cigaree lighter socket in the car DC 12V-32V Main Menu 1 2 3 4 5 6 7 UP Arrow Menu / Selection button Down arrow Parking Line on/off and Adjust Parking Line Position Confirm / CH Selection Antenna Connection Bracket mount 7 6

(RED) ACC DC 12V-24V

(BLACK) Ground Pairing System has been paired, connect power and it works. Use pairing unless you need to add more cameras or replace a camera. CAMERA CONNECTION: Locate the clearance lights wiring on your vehicle. You may need to remove the interior panel in order to locate. Connect the power cables for camera: Red wire to light's posive;

Black wire to chassis ground. MONITOR CONNECTION: Cigaree lighter adapter: rmly insert the lighter plug to the cigaree lighter socket. DO NOT INSTALL monitor where it may obstruct driver view or obstruct air bag devices. PAIRING PICTURE MIR-FLIP SYSTEM PAIRING START 20 Posion Camera 3 Monitor Camera Pairing:

1. Un-plug camera's power connecon 2. Keep monitor is power connected 3. Press monitor buon " Menu", press " " or " " scroll to Pairing 4. Press "OK", monitor appears countdown 20 seconds 5. Connect camera to its power source 6. Camera signal appears on monitor Note: no need to press any buon on camera

(RED) ACC DC 12-24V

(BLACK) Ground 4 FCC Warning Statement: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Radiation Exposure Statement The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be colocated for operating in conjunction with any other antenna or transmitter.

C5266091_X24_Ed.1 Attestation Statements TO:

Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 The Commission adopted rules covered telecommunications equipment and video surveillance equipment produced by entities identified on the Commissions Covered List1, which is periodically updated. See the Covered List for more details. This Attestation Statement is to confirm that we follow the Section 2.911(d)(5)(i)-(ii) that prohibit equipment authorization for Applicant Company name: Forsafe Co.Ltd Grantee code:2A9OS FCC ID:2A9OS-YW-0199TX Contact Name: Owen meng Address: NO.1 Xinglong Four Street, Dahua, Huacheng, HuaDu District, Guangzhou, China 510800 Telephone No: 0086-20-36915586 Fax No: 0086-20-36915586 Email: owen@51forsafe.com i.

[Forsafe Co.Ltd] (the applicant) certifies that the equipment for which authorization is sought is not covered equipment prohibited from receiving an equipment authorization pursuant to sectio n 2.903 of the FCC rules. The applicant must sign this certification. ii.

[Forsafe Co.Ltd] (the applicant) certifies that, as of the date of the filing of the application, the applicant [is not] identified on the Covered List as an entity producing covered equipment. The applicant must sign this certification. Date: 2023/02/09 Applicants Name:Owen Meng Title:Manager Signatur e 1 The Commissions Covered List is published by the Public Safety and Homeland Security Bureau and posted on the Commissions website. This Covered List, which is periodically updated, identifies particular equipment, produced by particular entities, that constitutes covered equipment. https://www.fcc.gov/supplychain/coveredlist 1/1

C5266091_X10_Ed.1

< Forsafe Co.Ltd >

Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Subject: Request for Confidentiality FCC ID:2A9OS-YW-0199TX To Whom It May Concern, Date: 2023-01-06 Pursuant to the provisions of Sections 0.457 and 0.459 of Commission's rules

(47CFR0.457, 0.459), we are requesting the Commission to withhold the following attachment(s) as confidential document from public disclosure. Exhibits ID Label/Location Attestation Statement External Photos Block Diagram Schematics Test Report Test Setup Photos Users Manual Internal Photos Parts List / Tune Up RF Exposure Info Operational Description Cover Letter(s) SDR Software / Security Info Long-Term Confidentiality No No No Short-Term Confidentiality No No No No No No No No Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature:

Name: Owen Meng Title: N/A 1/1

Forsafe Co.Ltd Model Difference Product description: wireless backup camera Model name:YW-0199TX YW-088, YW-34132TX, YW-0669TX Trade Name: yuwei FCC ID:2A9OS-YW-0199TX All the model are the same circuit and RF module, only for model name. Regards Sincerely Clients signature:

Clients name / title : Owen Meng (N/A) Contact information / address:NO.1 Xinglong Four Street, Dahua, Huacheng, HuaDu District, Guangzhou, China 510800

C5266091_X8_Ed.1 Letter of Authorization

<Forsafe Co.Ltd >

Company:Forsafe Co.Ltd Address:6F NO.1 Xinglong Four Street, Dahua, Huacheng, HuaDu District,Guangzhou, China 510800 Product Name: wireless backup camera Model Number: YW-0199TX YW-088, YW-34132TX, YW-0669TX FCC Identifier:2A9OS-YW-0199TX We authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, to act on our behalf on all matters concerning the above named equipment. Any individual within LGAI Technological Center S.A. is authorized to act on our behalf and take action on the application. We declare that authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, information related to the approval project to the Federal Communication Commission and to discuss any issues concerning the approval application. Any and all acts carried out by LGAI Technological Center S.A. on our behalf shall have the same effect as acts of our own is allowed to forward all

. Name: Owen Meng Date: 2023-01-06 Title: N/A Signature of applicant:

1/1

C5266091_X23_Ed.1 US AGENT LETTER OF ATTESTATION US Agent:

Company Name:

Contact Name:

Address:

Telephone No:

Fax No:

Email:

Ttriton Signal Jean Howard 1025 N. LOMBARD ROAD LOMBARD, IL 60148 USA 877 874 3744 jean.h@triton-signal.com TO:

Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 the Forsafe Co.Ltd noted below for This letter is to confirm that we have accepted the responsibility to act as US agent future FCC representative on behalf of certification/registrations obtained during the period of this agreement, which ends at the specified date below. As per US agent, we are aware of the requirements involved as outlined in FCC Equipment Authorization Program in their Report and Order FCC 22-84 and the clause 2.911 Application requirements. all Applicant Company name: Forsafe Co.Ltd Grantee code: 2A9OS FCC ID: 2A9OS-YW-0199TX Contact Name: Owen Meng Address: NO.1 Xinglong Four Street, Dahua, Huacheng, HuaDu District, Guangzhou, China 510800 Telephone No: 0086-20-36915586 Fax No: 0086-20-36915586 Email: owen@51forsafe.com TheApplicantacknowledgetheacceptanceofitsobligationtomaintainanagentfor service of process in the United States for no less than one year after either the granteehaspermanentlyterminatedallmarketingandimportationoftheapplicable equipment within the U.S., or the conclusion of any Commission-related administrativeorjudicialproceedinginvolvingtheequipment,whicheverislater. Date: 2023/02/09 Applicants Name:Owen Meng Title:Manager Signature US Agents Name:Jean Howard Title:Manager Signature 1/1 C5266091_X23_Ed.1 1/1