FOURING DA1010-1066/1066(A) Wireless Charger Instruction Manual Safety Instructions Read and follow all safety instructions. 1. Applicable operation temperature range is from 0 to 30 and can be stored at ambient temperature between 0to50 with ambient humidity less than or equal to 90%. Pad or battery of the charging mobile device may be damaged if Pad is not being used properly. 2. Avoid Pad receiving violent impact or intentional pressing, exposing to the sun and rain, or getting contact with corrosive substances. Keep away from fire. 3. Use Pad with certified adapter ONLY or those applied to international standard rules (5V/2A, 9V/1.67A). 4. Do not disassemble, modify or repair Pad yourself. Contact your distributor for after sale service if there's any questions. 5. Avoid children and pets chewing or swallowing Pad. 6. Recycle Pad properly for environmental protection. Hazardous substance test result:
Mercury / Cadmium / Chromium 6 / PB / PBDEs (O) O: Content of the hazardous substances in all homogenous materials of the part is below the prescribed limits in accordance with GB/T26572 standard. Lead (X) X: Content of the hazardous substances in a homogeneous material of the part is exceeding the prescribed limits in accordance with GB/T26572 standard. Parts A. Wireless charger RX B. Wireless charger cable User Guide 1. Plug in USB to power with certified adapter (QC 2.0 or 3.0 adapter is required). 2. Place mobile device (with wireless receiver built-in or attached) onto Pad's surface evenly and properly. 3. Remove mobile device from Pad's surface when it is fully charged. Troubleshooting 1. Pad is not working. Check and make sure Pad's USB plug-in is well connected to proper power and/or adapter. 2. Mobile device is power off during charging or not being fully charged. Check and make sure the adapter is a certified product or those applied only to international standard rules. One Year Warranty Shenzhen Qitian Taiyi Technology Company Limited (hereinafter referred to "Company") warrants this product (see Exclusions below) to the original purchaser against defective material and workmanship that occurs during normal use for one year. Company will, at Company's option, either repair or replace same without charge (but no cash refunds will be made). 1. Damage resulting from accident, misuse, abuse, lack of reasonable care, subjecting the product to any but the specified electrical service, other than normal and ordinary use of the product, subjecting the product to abnormal working conditions or any other failure not resulting from defects in materials or workmanship. 2. Damage resulting from modification, tampering with or attempted repair by anyone other than the Company or designated repair representative by the Company. 3. Transfer of product to someone other than the original consumer purchaser. 4. The warranty is not valid for components subject to wear and/or to counterfeits. FCC ID: 2AT9V-DA1010 FCC Requirement changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.