FCC ID: SQK-MBH7BTZXXC2 Bluetooth Module

Bluetooth SPP Module Operation Manual Rev.01 JUN 6, 2012 Fujitsu Component Limited Page 2 1. INTRODUCTION ....................................................................................................................... 3 2. COPYRIGHT NOTICE AND DISCLAIMER ............................................................................... 3 3. NECESSARY ITEM.................................................................................................................... 3 3.1 MBH-SAKURA2 CIRCUIT DIAGRAM..........................................................................................4 4. SET-UP FOR BLUETOOTH SPP CONNECTION ...................................................................... 5 5. REQUIRED SOFTWARE............................................................................................................ 6 6. SETTING OF TERA TERM ........................................................................................................ 6 7. OPERATING PROCEDURE FOR TX/RX MODE CONTROL..................................................... 7 7.1 7.2 MODE CHANGE OF THE SPP BLUETOOTH MODULE ....................................................................7 OPERATION OF TEST TOOL BY CSR ............................................................................................8 8. TEST COMMANDS .................................................................................................................. 10 8.1 TX MODE COMMAND .................................................................................................................10 8.1.1 8.1.2 8.1.3 8.1.4 Tx Unmodulated wave setting.........................................................................................10 Tx Modulated wave setting .............................................................................................10 Tx 79 channels frequency hopping setting......................................................................11 Tx AFH 20 channels AFH (Adaptive Frequency Hopping) setting.................................11 RX MODE COMMAND .................................................................................................................12 8.2 Copyright FUJITSU COMPONENT LIMITED 2012 Page 3 1. INTRODUCTION This document describes the method of Tx/Rx mode control for Bluetooth SPP Module provided by FCL

(Fujitsu Component Limited) 2. Copyright Notice and Disclaimer Copyright 2012 FUJITSU COMPONENT LIMITED. All rights reserved BLUETOOTH, The Bluetooth Figure Mark, and the Bluetooth Combination Mark are registered trademarks owned by Bluetooth SIG, Inc. Windows is a registered trademark of Microsoft Corporation in the United States and other countries. Linux is a registered trademark of Mr. Linus Torvalds in Japan and other countries Other third-party brands and names are the property of their respective owners. This document is subject to change without any prior notice. 3. Necessary item MBH-SAKURA2: Bluetooth SPP Module Evaluation board

USB Cable PC Bluetooth SPP Module with Daughter Board MBH7BTZ42-DAUGHTER MBH7BTZ52-DAUGHTER Or Bluetooth SPP Module with connector MBH7BTZ40 MBH7BTZ43 MBH7BTZ50 MBH7BTZ53 Copyright FUJITSU COMPONENT LIMITED 2012 Page 4 3.1 MBH-SAKURA2 Circuit diagram Copyright FUJITSU COMPONENT LIMITED 2012 Page 5 4. SET-UP for Bluetooth SPP connection Connect CN2 connector on MBH-SAKURA2 and the USB port on PC with USB cable to control Bluetooth SPP module (Figure 4-1). To work with the USB serial port (UART over USB), first download the FTDI FT232R driver (D2XX and VCP) from:

http://www.ftdichip.com/Drivers/VCP.htm Install the driver according to the installation guide available on the FTDI web site. After the driver is installed, go to My Computer->Properties->Hardware->Device Manager->Ports to identify the COM port to which the USB serial port is assigned.

-The baud rate is set to 115.2kbps (Default setting) USB port CN2 Figure 4-1: Hardware Setup Copyright FUJITSU COMPONENT LIMITED 2012 Page 6 5. Required Software BlueSuite test tool by CSR. Account registration is required to download from the support website of CSR. When there is no account, please contact your local sales. Tera Term is terminal software to control Bluetooth SPP module. Tera Term is downloadable from the following website. http://ttssh2.sourceforge.jp/

6. Setting of Tera Term When you use Tera Term, please change the setting as below. Select COM Port No which is assigned USB Serial port Copyright FUJITSU COMPONENT LIMITED 2012 Page 7 7. Operating Procedure for Tx/Rx mode control 7.1 Mode change of the SPP Bluetooth module Connect CN2 connector on MBH-SAKURA2 and the USB port on PC witha USB cable to control Bluetooth SPP Module. And, launch the Tera Term. Input the BCSP_MODE command to change from SPP mode to BCSP mode.

*Note: Since it is temporary, this module will operate SPP mode after reset (or power on). Copyright FUJITSU COMPONENT LIMITED 2012 Page 8 7.2 Operation of Test tool by CSR Close Tera Term after changing SPP Bluetooth module to BCSP mode. And, execute BtCLI from Windows start menu. Set up as follows and click "OK.". Select COM Port No which is assigned USB Serial port Copyright FUJITSU COMPONENT LIMITED 2012 Page 9 The command prompt window is opend as follows. SPP Bluetooth module is controlled by command line interface. Refer to the following page for the details of a command. (The following is example for the setup of unmodulated, BasicRate, DH5 packet.) Copyright FUJITSU COMPONENT LIMITED 2012 8. Test Commands Page 10 8.1 Tx mode command 8.1.1 Tx Unmodulated wave setting Transfer NameSetting item 1 Select "TX/RX interval Value" using rt command

<"cfg_frq">

2 Select "Packet Type"

using rt command

<"cfg_pkt">

3 Select "Output Power"

using rt command

<"txstart">

rate

-

Basic Rate EDR 2M EDR 3M Basic Rate EDR 2M/3M Packet type Ch The command to input DH1 DH3 DH5 DH1 DH3 DH5 DH1 DH3 DH5 DH1 DH3 DH5

-

-

-

-

-

-

-

-

-

-

-

-

-

-

Ch0 Ch39 Ch78 Ch0 Ch39 Ch78 rt0x160x4e20x0 rt0x160x9c40x0 rt0x160xea60x0 rt0x170x40x1b rt0x170xb0xb7 rt0x170xf0x153 rt0x170x140x36 rt0x170x1a0x16f rt0x170x1e0x2a7 rt0x170x180x53 rt0x170x1b0x228 rt0x170x1f0x3fd rttxstart0x9620x35 rttxstart0x9890x35 rttxstart0x9b00x35 rttxstart0x9620x5f rttxstart0x9890x5f rttxstart0x9b00x5f 8.1.2 Tx Modulated wave setting NameSetting item 1 Select "TX/RX interval Value" using rt command

<"cfg_frq">

2 Select

"Packet Type"

using rt command

<"cfg_pkt">

3 Select "Output Power"

using rt command

<"txdata1">

Transfer rate Packet type Ch The command to input DH1 DH3 DH5 DH1 DH3 DH5 DH1 DH3 DH5 DH1 DH3 DH5

-

-

-

Basic Rate EDR 2M EDR 3M Basic Rate EDR 2M/3M

-

-

-

-

-

-

-

-

-

-

-

-

Ch0 Ch39 Ch78 Ch0 Ch39 Ch78 rt0x160x4e20x0 rt0x160x9c40x0 rt0x160xea60x0 rt0x170x40x1b rt0x170xb0xb7 rt0x170xf0x153 rt0x170x140x36 rt0x170x1a0x16f rt0x170x1e0x2a7 rt0x170x180x53 rt0x170x1b0x228 rt0x170x1f0x3fd rttxdata10x9620x35 rttxdata10x9890x35 rttxdata10x9b00x35 rttxdata10x9620x5f rttxdata10x9890x5f rttxdata10x9b00x5f Copyright FUJITSU COMPONENT LIMITED 2012 8.1.3 Tx 79 channels frequency hopping setting Page 11 NameSetting item 1 Select "TX/RX interval Value" using rt command

<"cfg_frq">

2 Select

"Packet Type"

using rt command

<"cfg_pkt">

3 Select "Output Power"

using rt command

<"txdata2">

Transfer rate Packet type Ch The command to input DH1 DH3 DH5 DH1 DH3 DH5 DH1 DH3 DH5 DH1 DH3 DH5

-

-

-

Basic Rate EDR 2M EDR 3M Basic Rate EDR 2M/3M

-

-

-

-

-

-

-

-

-

-

-

-

-

-

rt0x160x4e20x0 rt0x160x9c40x0 rt0x160xea60x0 rt0x170x40x1b rt0x170xb0xb7 rt0x170xf0x153 rt0x170x140x36 rt0x170x1a0x16f rt0x170x1e0x2a7 rt0x170x180x53 rt0x170x1b0x228 rt0x170x1f0x3fd rttxdata20x00x35 rttxdata20x00x5f 8.1.4 Tx AFH 20 channels AFH (Adaptive Frequency Hopping) setting NameSetting item 1 Select "TX/RX interval Value" using rt command

<"cfg_frq">

2 Select

"Packet Type"

using rt command

<"cfg_pkt">

3 Select "Necessary frequency range of AFH"

using rt command 4 Select "Output Power"

using rt command

<"txdata2">

Transfer rate Packet type Ch The command to input

-

EDR 2M Basic Rate DH1 DH3 DH5 DH1 DH3 DH5 DH1 DH3 DH5 DH1 DH3 DH5 Low (Ch 0-19) Middle (Ch 28-47) High (Ch 59-78) Basic Rate EDR 2M/3M EDR 3M

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

rt0x160x4e20x0 rt0x160x9c40x0 rt0x160xea60x0 rt0x170x40x1b rt0x170xb0xb7 rt0x170xf0x153 rt0x170x140x36 rt0x170x1a0x16f rt0x170x1e0x2a7 rt0x170x180x53 rt0x170x1b0x228 rt0x170x1f0x3fd rt0x002d0xffff0x000f0x00000x00000x0000 rt0x002d0x00000xf0000xffff0x00000x0000 rt0x002d0x00000x00000x00000xf8000x7fff rttxdata20x00x35 rttxdata20x00x5f Copyright FUJITSU COMPONENT LIMITED 2012 Page 12 8.2 Rx mode command NameSetting item 1 Select "TX/RX interval Value" using rt command

<"cfg_frq">

2 Select

"Packet Type"

using rt command

<"cfg_pkt">

3 Set rt command

<" rxstart1">

Transfer rate Packet type Ch The command to input

-

-

-

-

-

-

-

-

rt0x160xea60x0 rt0x170xf0x153 Ch0 Ch39 Ch78 rtrxstart10x962 rtrxstart10x989 rtrxstart10x9b0 Copyright FUJITSU COMPONENT LIMITED 2012 Note to users in the United States of America Notice:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Caution:

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Declaration of Conformity Product Name: Bluetooth Module Model Number: MBH7BTZ53 Responsible party: Fujitsu Components America, Inc. Address: 250 E. Caribbean Drive, Sunnyvale, CA 94089 U.S.A. Telephone number: 408-745-4900 This device complies with part 15 of FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. Note to users in Canada Note:

Remarque concernant les utilisateurs au Canada Avertissement:

This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numrique de la classe B est conforme la norme NMB-003 du Canada. Note to users It is strictly forbidden to use antenna except designated. This equipment must not be co-located or operated in conjunction with any other antenna or transmitter. This equipment complies with FCC/IC radiation exposure limits set forth for uncontrolled equipment and meets the FCC radio frequency (RF) Exposure Guidelines in Supplement C to OET65 and RSS-102 of the IC radio frequency (RF) Exposure rules. Cet quipement est conforme aux limites dexposition aux rayonnements nonces pour un environnement non contrl et respecte les rgles dexposition aux frquences radiolectriques (RF) CNR-102 de lIC. Cet quipement met une nergie RF trs faible qui est considre conforme sans valuation de lexposition maximale autorise. Note to users in Canada This device complies with RSS-Gen of IC Rules. Operation is subject to the following two conditions;

1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. Remarque concermant les utilisateurs au Canada Ce dispositif est conforme la norme CNR-Gen dIndustrie Canada. Lutilisation de ce dispositif est autorise seulement aux deux conditions suivantes:

(1)il ne doit pas produire de brouillage et (2) lutilisateur du dispositif doit tre prt accepter tout brouillage radiolectrique reu, mme si ce brouillage est susceptible de compromettre le fonctionnement du dispositif. Note to users in the United States of America Notice:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Caution:

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Declaration of Conformity Product Name: Bluetooth Module Model Number: MBH7BTZ52 Responsible party: Fujitsu Components America, Inc. Address: 250 E. Caribbean Drive, Sunnyvale, CA 94089 U.S.A. Telephone number: 408-745-4900 This device complies with part 15 of FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. Note to users in Canada Note:

Remarque concernant les utilisateurs au Canada Avertissement:

This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numrique de la classe B est conforme la norme NMB-003 du Canada. Note to users It is strictly forbidden to use antenna except designated. This equipment must not be co-located or operated in conjunction with any other antenna or transmitter. This equipment complies with FCC/IC radiation exposure limits set forth for uncontrolled equipment and meets the FCC radio frequency (RF) Exposure Guidelines in Supplement C to OET65 and RSS-102 of the IC radio frequency (RF) Exposure rules. Cet quipement est conforme aux limites dexposition aux rayonnements nonces pour un environnement non contrl et respecte les rgles dexposition aux frquences radiolectriques (RF) CNR-102 de lIC. Cet quipement met une nergie RF trs faible qui est considre conforme sans valuation de lexposition maximale autorise. Note to users in Canada This device complies with RSS-Gen of IC Rules. Operation is subject to the following two conditions;

1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. Remarque concermant les utilisateurs au Canada Ce dispositif est conforme la norme CNR-Gen dIndustrie Canada. Lutilisation de ce dispositif est autorise seulement aux deux conditions suivantes:

(1)il ne doit pas produire de brouillage et (2) lutilisateur du dispositif doit tre prt accepter tout brouillage radiolectrique reu, mme si ce brouillage est susceptible de compromettre le fonctionnement du dispositif. Note to users in the United States of America Notice:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Caution:

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Declaration of Conformity Product Name: Bluetooth Module Model Number: MBH7BTZ50 Responsible party: Fujitsu Components America, Inc. Address: 250 E. Caribbean Drive, Sunnyvale, CA 94089 U.S.A. Telephone number: 408-745-4900 This device complies with part 15 of FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. Note to users in Canada Note:

Remarque concernant les utilisateurs au Canada Avertissement:

This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numrique de la classe B est conforme la norme NMB-003 du Canada. Note to users It is strictly forbidden to use antenna except designated. This equipment must not be co-located or operated in conjunction with any other antenna or transmitter. This equipment complies with FCC/IC radiation exposure limits set forth for uncontrolled equipment and meets the FCC radio frequency (RF) Exposure Guidelines in Supplement C to OET65 and RSS-102 of the IC radio frequency (RF) Exposure rules. Cet quipement est conforme aux limites dexposition aux rayonnements nonces pour un environnement non contrl et respecte les rgles dexposition aux frquences radiolectriques (RF) CNR-102 de lIC. Cet quipement met une nergie RF trs faible qui est considre conforme sans valuation de lexposition maximale autorise. Note to users in Canada This device complies with RSS-Gen of IC Rules. Operation is subject to the following two conditions;

1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. Remarque concermant les utilisateurs au Canada Ce dispositif est conforme la norme CNR-Gen dIndustrie Canada. Lutilisation de ce dispositif est autorise seulement aux deux conditions suivantes:

(1)il ne doit pas produire de brouillage et (2) lutilisateur du dispositif doit tre prt accepter tout brouillage radiolectrique reu, mme si ce brouillage est susceptible de compromettre le fonctionnement du dispositif. Note to users in the United States of America Notice:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Caution:

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Declaration of Conformity Product Name: Bluetooth Module Model Number: MBH7BTZ43 Responsible party: Fujitsu Components America, Inc. Address: 250 E. Caribbean Drive, Sunnyvale, CA 94089 U.S.A. Telephone number: 408-745-4900 This device complies with part 15 of FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. Note to users in Canada Note:

Remarque concernant les utilisateurs au Canada Avertissement:

This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numrique de la classe B est conforme la norme NMB-003 du Canada. Note to users It is strictly forbidden to use antenna except designated. This equipment must not be co-located or operated in conjunction with any other antenna or transmitter. This equipment complies with FCC/IC radiation exposure limits set forth for uncontrolled equipment and meets the FCC radio frequency (RF) Exposure Guidelines in Supplement C to OET65 and RSS-102 of the IC radio frequency (RF) Exposure rules. Cet quipement est conforme aux limites dexposition aux rayonnements nonces pour un environnement non contrl et respecte les rgles dexposition aux frquences radiolectriques (RF) CNR-102 de lIC. Cet quipement met une nergie RF trs faible qui est considre conforme sans valuation de lexposition maximale autorise. Note to users in Canada This device complies with RSS-Gen of IC Rules. Operation is subject to the following two conditions;

1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. Remarque concermant les utilisateurs au Canada Ce dispositif est conforme la norme CNR-Gen dIndustrie Canada. Lutilisation de ce dispositif est autorise seulement aux deux conditions suivantes:

(1)il ne doit pas produire de brouillage et (2) lutilisateur du dispositif doit tre prt accepter tout brouillage radiolectrique reu, mme si ce brouillage est susceptible de compromettre le fonctionnement du dispositif. Note to users in the United States of America Notice:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Caution:

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Declaration of Conformity Product Name: Bluetooth Module Model Number: MBH7BTZ42 Responsible party: Fujitsu Components America, Inc. Address: 250 E. Caribbean Drive, Sunnyvale, CA 94089 U.S.A. Telephone number: 408-745-4900 This device complies with part 15 of FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. Note to users in Canada Note:

Remarque concernant les utilisateurs au Canada Avertissement:

This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numrique de la classe B est conforme la norme NMB-003 du Canada. Note to users It is strictly forbidden to use antenna except designated. This equipment must not be co-located or operated in conjunction with any other antenna or transmitter. This equipment complies with FCC/IC radiation exposure limits set forth for uncontrolled equipment and meets the FCC radio frequency (RF) Exposure Guidelines in Supplement C to OET65 and RSS-102 of the IC radio frequency (RF) Exposure rules. Cet quipement est conforme aux limites dexposition aux rayonnements nonces pour un environnement non contrl et respecte les rgles dexposition aux frquences radiolectriques (RF) CNR-102 de lIC. Cet quipement met une nergie RF trs faible qui est considre conforme sans valuation de lexposition maximale autorise. Note to users in Canada This device complies with RSS-Gen of IC Rules. Operation is subject to the following two conditions;

1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. Remarque concermant les utilisateurs au Canada Ce dispositif est conforme la norme CNR-Gen dIndustrie Canada. Lutilisation de ce dispositif est autorise seulement aux deux conditions suivantes:

(1)il ne doit pas produire de brouillage et (2) lutilisateur du dispositif doit tre prt accepter tout brouillage radiolectrique reu, mme si ce brouillage est susceptible de compromettre le fonctionnement du dispositif. Note to users in the United States of America Notice:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Caution:

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Declaration of Conformity Product Name: Bluetooth Module Model Number: MBH7BTZ40 Responsible party: Fujitsu Components America, Inc. Address: 250 E. Caribbean Drive, Sunnyvale, CA 94089 U.S.A. Telephone number: 408-745-4900 This device complies with part 15 of FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. Note to users in Canada Note:

Remarque concernant les utilisateurs au Canada Avertissement:

This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numrique de la classe B est conforme la norme NMB-003 du Canada. Note to users It is strictly forbidden to use antenna except designated. This equipment must not be co-located or operated in conjunction with any other antenna or transmitter. This equipment complies with FCC/IC radiation exposure limits set forth for uncontrolled equipment and meets the FCC radio frequency (RF) Exposure Guidelines in Supplement C to OET65 and RSS-102 of the IC radio frequency (RF) Exposure rules. Cet quipement est conforme aux limites dexposition aux rayonnements nonces pour un environnement non contrl et respecte les rgles dexposition aux frquences radiolectriques (RF) CNR-102 de lIC. Cet quipement met une nergie RF trs faible qui est considre conforme sans valuation de lexposition maximale autorise. Note to users in Canada This device complies with RSS-Gen of IC Rules. Operation is subject to the following two conditions;

1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. Remarque concermant les utilisateurs au Canada Ce dispositif est conforme la norme CNR-Gen dIndustrie Canada. Lutilisation de ce dispositif est autorise seulement aux deux conditions suivantes:

(1)il ne doit pas produire de brouillage et (2) lutilisateur du dispositif doit tre prt accepter tout brouillage radiolectrique reu, mme si ce brouillage est susceptible de compromettre le fonctionnement du dispositif.

Bluetooth SPP Module Operation Manual Rev.01 JUN 6, 2012 Fujitsu Component Limited Page 2 1. INTRODUCTION ....................................................................................................................... 3 2. COPYRIGHT NOTICE AND DISCLAIMER ............................................................................... 3 3. NECESSARY ITEM.................................................................................................................... 3 3.1 MBH-SAKURA2 CIRCUIT DIAGRAM..........................................................................................4 4. SET-UP FOR BLUETOOTH SPP CONNECTION ...................................................................... 5 5. REQUIRED SOFTWARE............................................................................................................ 6 6. SETTING OF TERA TERM ........................................................................................................ 6 7. OPERATING PROCEDURE FOR TX/RX MODE CONTROL..................................................... 7 7.1 7.2 MODE CHANGE OF THE SPP BLUETOOTH MODULE ....................................................................7 OPERATION OF TEST TOOL BY CSR ............................................................................................8 8. TEST COMMANDS .................................................................................................................. 10 8.1 TX MODE COMMAND .................................................................................................................10 8.1.1 8.1.2 8.1.3 8.1.4 Tx Unmodulated wave setting.........................................................................................10 Tx Modulated wave setting .............................................................................................10 Tx 79 channels frequency hopping setting......................................................................11 Tx AFH 20 channels AFH (Adaptive Frequency Hopping) setting.................................11 RX MODE COMMAND .................................................................................................................12 8.2 Copyright FUJITSU COMPONENT LIMITED 2012 Page 3 1. INTRODUCTION This document describes the method of Tx/Rx mode control for Bluetooth SPP Module provided by FCL

(Fujitsu Component Limited) 2. Copyright Notice and Disclaimer Copyright 2012 FUJITSU COMPONENT LIMITED. All rights reserved BLUETOOTH, The Bluetooth Figure Mark, and the Bluetooth Combination Mark are registered trademarks owned by Bluetooth SIG, Inc. Windows is a registered trademark of Microsoft Corporation in the United States and other countries. Linux is a registered trademark of Mr. Linus Torvalds in Japan and other countries Other third-party brands and names are the property of their respective owners. This document is subject to change without any prior notice. 3. Necessary item MBH-SAKURA2: Bluetooth SPP Module Evaluation board

USB Cable PC Bluetooth SPP Module with Daughter Board MBH7BTZ42-DAUGHTER MBH7BTZ52-DAUGHTER Or Bluetooth SPP Module with connector MBH7BTZ40 MBH7BTZ43 MBH7BTZ50 MBH7BTZ53 Copyright FUJITSU COMPONENT LIMITED 2012 Page 4 3.1 MBH-SAKURA2 Circuit diagram Copyright FUJITSU COMPONENT LIMITED 2012 Page 5 4. SET-UP for Bluetooth SPP connection Connect CN2 connector on MBH-SAKURA2 and the USB port on PC with USB cable to control Bluetooth SPP module (Figure 4-1). To work with the USB serial port (UART over USB), first download the FTDI FT232R driver (D2XX and VCP) from:

http://www.ftdichip.com/Drivers/VCP.htm Install the driver according to the installation guide available on the FTDI web site. After the driver is installed, go to My Computer->Properties->Hardware->Device Manager->Ports to identify the COM port to which the USB serial port is assigned.

-The baud rate is set to 115.2kbps (Default setting) USB port CN2 Figure 4-1: Hardware Setup Copyright FUJITSU COMPONENT LIMITED 2012 Page 6 5. Required Software BlueSuite test tool by CSR. Account registration is required to download from the support website of CSR. When there is no account, please contact your local sales. Tera Term is terminal software to control Bluetooth SPP module. Tera Term is downloadable from the following website. http://ttssh2.sourceforge.jp/

6. Setting of Tera Term When you use Tera Term, please change the setting as below. Select COM Port No which is assigned USB Serial port Copyright FUJITSU COMPONENT LIMITED 2012 Page 7 7. Operating Procedure for Tx/Rx mode control 7.1 Mode change of the SPP Bluetooth module Connect CN2 connector on MBH-SAKURA2 and the USB port on PC witha USB cable to control Bluetooth SPP Module. And, launch the Tera Term. Input the BCSP_MODE command to change from SPP mode to BCSP mode.

*Note: Since it is temporary, this module will operate SPP mode after reset (or power on). Copyright FUJITSU COMPONENT LIMITED 2012 Page 8 7.2 Operation of Test tool by CSR Close Tera Term after changing SPP Bluetooth module to BCSP mode. And, execute BtCLI from Windows start menu. Set up as follows and click "OK.". Select COM Port No which is assigned USB Serial port Copyright FUJITSU COMPONENT LIMITED 2012 Page 9 The command prompt window is opend as follows. SPP Bluetooth module is controlled by command line interface. Refer to the following page for the details of a command. (The following is example for the setup of unmodulated, BasicRate, DH5 packet.) Copyright FUJITSU COMPONENT LIMITED 2012 8. Test Commands Page 10 8.1 Tx mode command 8.1.1 Tx Unmodulated wave setting Transfer NameSetting item 1 Select "TX/RX interval Value" using rt command

<"cfg_frq">

2 Select "Packet Type"

using rt command

<"cfg_pkt">

3 Select "Output Power"

using rt command

<"txstart">

rate

Basic Rate EDR 2M EDR 3M Basic Rate EDR 2M/3M Packet type Ch The command to input DH1 DH3 DH5 DH1 DH3 DH5 DH1 DH3 DH5 DH1 DH3 DH5

Ch0 Ch39 Ch78 Ch0 Ch39 Ch78 rt0x160x4e20x0 rt0x160x9c40x0 rt0x160xea60x0 rt0x170x40x1b rt0x170xb0xb7 rt0x170xf0x153 rt0x170x140x36 rt0x170x1a0x16f rt0x170x1e0x2a7 rt0x170x180x53 rt0x170x1b0x228 rt0x170x1f0x3fd rttxstart0x9620x35 rttxstart0x9890x35 rttxstart0x9b00x35 rttxstart0x9620x5f rttxstart0x9890x5f rttxstart0x9b00x5f 8.1.2 Tx Modulated wave setting NameSetting item 1 Select "TX/RX interval Value" using rt command

<"cfg_frq">

2 Select

"Packet Type"

using rt command

<"cfg_pkt">

3 Select "Output Power"

using rt command

<"txdata1">

Transfer rate Packet type Ch The command to input DH1 DH3 DH5 DH1 DH3 DH5 DH1 DH3 DH5 DH1 DH3 DH5

Basic Rate EDR 2M EDR 3M Basic Rate EDR 2M/3M

Ch0 Ch39 Ch78 Ch0 Ch39 Ch78 rt0x160x4e20x0 rt0x160x9c40x0 rt0x160xea60x0 rt0x170x40x1b rt0x170xb0xb7 rt0x170xf0x153 rt0x170x140x36 rt0x170x1a0x16f rt0x170x1e0x2a7 rt0x170x180x53 rt0x170x1b0x228 rt0x170x1f0x3fd rttxdata10x9620x35 rttxdata10x9890x35 rttxdata10x9b00x35 rttxdata10x9620x5f rttxdata10x9890x5f rttxdata10x9b00x5f Copyright FUJITSU COMPONENT LIMITED 2012 8.1.3 Tx 79 channels frequency hopping setting Page 11 NameSetting item 1 Select "TX/RX interval Value" using rt command

<"cfg_frq">

2 Select

"Packet Type"

using rt command

<"cfg_pkt">

3 Select "Output Power"

using rt command

<"txdata2">

Transfer rate Packet type Ch The command to input DH1 DH3 DH5 DH1 DH3 DH5 DH1 DH3 DH5 DH1 DH3 DH5

Basic Rate EDR 2M EDR 3M Basic Rate EDR 2M/3M

rt0x160x4e20x0 rt0x160x9c40x0 rt0x160xea60x0 rt0x170x40x1b rt0x170xb0xb7 rt0x170xf0x153 rt0x170x140x36 rt0x170x1a0x16f rt0x170x1e0x2a7 rt0x170x180x53 rt0x170x1b0x228 rt0x170x1f0x3fd rttxdata20x00x35 rttxdata20x00x5f 8.1.4 Tx AFH 20 channels AFH (Adaptive Frequency Hopping) setting NameSetting item 1 Select "TX/RX interval Value" using rt command

<"cfg_frq">

2 Select

"Packet Type"

using rt command

<"cfg_pkt">

3 Select "Necessary frequency range of AFH"

using rt command 4 Select "Output Power"

using rt command

<"txdata2">

Transfer rate Packet type Ch The command to input

EDR 2M Basic Rate DH1 DH3 DH5 DH1 DH3 DH5 DH1 DH3 DH5 DH1 DH3 DH5 Low (Ch 0-19) Middle (Ch 28-47) High (Ch 59-78) Basic Rate EDR 2M/3M EDR 3M

rt0x160x4e20x0 rt0x160x9c40x0 rt0x160xea60x0 rt0x170x40x1b rt0x170xb0xb7 rt0x170xf0x153 rt0x170x140x36 rt0x170x1a0x16f rt0x170x1e0x2a7 rt0x170x180x53 rt0x170x1b0x228 rt0x170x1f0x3fd rt0x002d0xffff0x000f0x00000x00000x0000 rt0x002d0x00000xf0000xffff0x00000x0000 rt0x002d0x00000x00000x00000xf8000x7fff rttxdata20x00x35 rttxdata20x00x5f Copyright FUJITSU COMPONENT LIMITED 2012 Page 12 8.2 Rx mode command NameSetting item 1 Select "TX/RX interval Value" using rt command

<"cfg_frq">

2 Select

"Packet Type"

using rt command

<"cfg_pkt">

3 Set rt command

<" rxstart1">

Transfer rate Packet type Ch The command to input

rt0x160xea60x0 rt0x170xf0x153 Ch0 Ch39 Ch78 rtrxstart10x962 rtrxstart10x989 rtrxstart10x9b0 Copyright FUJITSU COMPONENT LIMITED 2012 Note to users in the United States of America Notice:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Caution:

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Declaration of Conformity Product Name: Bluetooth Module Model Number: MBH7BTZ40 Responsible party: Fujitsu Components America, Inc. Address: 250 E. Caribbean Drive, Sunnyvale, CA 94089 U.S.A. Telephone number: 408-745-4900 This device complies with part 15 of FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. Note to users in Canada Note:

This Class B digital apparatus complies with Canadian ICES-003. Remarque concernant les utilisateurs au Canada Avertissement:

Cet appareil numrique de la classe B est conforme la norme NMB-003 du Canada. Note to users It is strictly forbidden to use antenna except designated. This equipment must not be co-located or operated in conjunction with any other antenna or transmitter. This equipment complies with FCC/IC radiation exposure limits set forth for uncontrolled equipment and meets the FCC radio frequency (RF) Exposure Guidelines in Supplement C to OET65 and RSS-102 of the IC radio frequency (RF) Exposure rules. This equipment should be installed and operated with at least 20cm more between the radiator and person's body(excluding extremities:hands, wrists, feet and ankles). Cet quipement est conforme aux limites dexposition aux rayonnements nonces pour un environnement non contrl et respecte les rgles dexposition aux frquences radiolectriques (RF) CNR-102 de lIC. Cet quipement met une nergie RF trs faible qui est considre conforme sans valuation de lexposition maximale autorise. Cependant, cet quipement doit tre install et utilis en gardant une distance de 20 cm ou plus entre le dispositif rayonnant et le corps ( lexception des extrmits : mains, poignets, pieds et chevilles). Note to users in Canada This device complies with RSS-Gen of IC Rules. Operation is subject to the following two conditions;

1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. Remarque concermant les utilisateurs au Canada Ce dispositif est conforme la norme CNR-Gen dIndustrie Canada. Lutilisation de ce dispositif est autorise seulement aux deux conditions suivantes:

(1)il ne doit pas produire de brouillage et (2) lutilisateur du dispositif doit tre prt accepter tout brouillage radiolectrique reu, mme si ce brouillage est susceptible de compromettre le fonctionnement du dispositif. Note to users in the United States of America Notice:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Caution:

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Declaration of Conformity Product Name: Bluetooth Module Model Number: MBH7BTZ42 Responsible party: Fujitsu Components America, Inc. Address: 250 E. Caribbean Drive, Sunnyvale, CA 94089 U.S.A. Telephone number: 408-745-4900 This device complies with part 15 of FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. Note to users in Canada Note:

This Class B digital apparatus complies with Canadian ICES-003. Remarque concernant les utilisateurs au Canada Avertissement:

Cet appareil numrique de la classe B est conforme la norme NMB-003 du Canada. Note to users It is strictly forbidden to use antenna except designated. This equipment must not be co-located or operated in conjunction with any other antenna or transmitter. This equipment complies with FCC/IC radiation exposure limits set forth for uncontrolled equipment and meets the FCC radio frequency (RF) Exposure Guidelines in Supplement C to OET65 and RSS-102 of the IC radio frequency (RF) Exposure rules. This equipment should be installed and operated with at least 20cm more between the radiator and person's body(excluding extremities:hands, wrists, feet and ankles). Cet quipement est conforme aux limites dexposition aux rayonnements nonces pour un environnement non contrl et respecte les rgles dexposition aux frquences radiolectriques (RF) CNR-102 de lIC. Cet quipement met une nergie RF trs faible qui est considre conforme sans valuation de lexposition maximale autorise. Cependant, cet quipement doit tre install et utilis en gardant une distance de 20 cm ou plus entre le dispositif rayonnant et le corps ( lexception des extrmits : mains, poignets, pieds et chevilles). Note to users in Canada This device complies with RSS-Gen of IC Rules. Operation is subject to the following two conditions;

1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. Remarque concermant les utilisateurs au Canada Ce dispositif est conforme la norme CNR-Gen dIndustrie Canada. Lutilisation de ce dispositif est autorise seulement aux deux conditions suivantes:

(1)il ne doit pas produire de brouillage et (2) lutilisateur du dispositif doit tre prt accepter tout brouillage radiolectrique reu, mme si ce brouillage est susceptible de compromettre le fonctionnement du dispositif. Note to users in the United States of America Notice:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Caution:

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Declaration of Conformity Product Name: Bluetooth Module Model Number: MBH7BTZ43 Responsible party: Fujitsu Components America, Inc. Address: 250 E. Caribbean Drive, Sunnyvale, CA 94089 U.S.A. Telephone number: 408-745-4900 This device complies with part 15 of FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. Note to users in Canada Note:

This Class B digital apparatus complies with Canadian ICES-003. Remarque concernant les utilisateurs au Canada Avertissement:

Cet appareil numrique de la classe B est conforme la norme NMB-003 du Canada. Note to users It is strictly forbidden to use antenna except designated. This equipment must not be co-located or operated in conjunction with any other antenna or transmitter. This equipment complies with FCC/IC radiation exposure limits set forth for uncontrolled equipment and meets the FCC radio frequency (RF) Exposure Guidelines in Supplement C to OET65 and RSS-102 of the IC radio frequency (RF) Exposure rules. This equipment should be installed and operated with at least 20cm more between the radiator and person's body(excluding extremities:hands, wrists, feet and ankles). Cet quipement est conforme aux limites dexposition aux rayonnements nonces pour un environnement non contrl et respecte les rgles dexposition aux frquences radiolectriques (RF) CNR-102 de lIC. Cet quipement met une nergie RF trs faible qui est considre conforme sans valuation de lexposition maximale autorise. Cependant, cet quipement doit tre install et utilis en gardant une distance de 20 cm ou plus entre le dispositif rayonnant et le corps ( lexception des extrmits : mains, poignets, pieds et chevilles). Note to users in Canada This device complies with RSS-Gen of IC Rules. Operation is subject to the following two conditions;

1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. Remarque concermant les utilisateurs au Canada Ce dispositif est conforme la norme CNR-Gen dIndustrie Canada. Lutilisation de ce dispositif est autorise seulement aux deux conditions suivantes:

(1)il ne doit pas produire de brouillage et (2) lutilisateur du dispositif doit tre prt accepter tout brouillage radiolectrique reu, mme si ce brouillage est susceptible de compromettre le fonctionnement du dispositif. Note to users in the United States of America Notice:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Caution:

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Declaration of Conformity Product Name: Bluetooth Module Model Number: MBH7BTZ52 Responsible party: Fujitsu Components America, Inc. Address: 250 E. Caribbean Drive, Sunnyvale, CA 94089 U.S.A. Telephone number: 408-745-4900 This device complies with part 15 of FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. Note to users in Canada Note:

This Class B digital apparatus complies with Canadian ICES-003. Remarque concernant les utilisateurs au Canada Avertissement:

Cet appareil numrique de la classe B est conforme la norme NMB-003 du Canada. Note to users It is strictly forbidden to use antenna except designated. This equipment must not be co-located or operated in conjunction with any other antenna or transmitter. This equipment complies with FCC/IC radiation exposure limits set forth for uncontrolled equipment and meets the FCC radio frequency (RF) Exposure Guidelines in Supplement C to OET65 and RSS-102 of the IC radio frequency (RF) Exposure rules. This equipment should be installed and operated with at least 20cm more between the radiator and person's body(excluding extremities:hands, wrists, feet and ankles). Cet quipement est conforme aux limites dexposition aux rayonnements nonces pour un environnement non contrl et respecte les rgles dexposition aux frquences radiolectriques (RF) CNR-102 de lIC. Cet quipement met une nergie RF trs faible qui est considre conforme sans valuation de lexposition maximale autorise. Cependant, cet quipement doit tre install et utilis en gardant une distance de 20 cm ou plus entre le dispositif rayonnant et le corps ( lexception des extrmits : mains, poignets, pieds et chevilles). Note to users in Canada This device complies with RSS-Gen of IC Rules. Operation is subject to the following two conditions;

1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. Remarque concermant les utilisateurs au Canada Ce dispositif est conforme la norme CNR-Gen dIndustrie Canada. Lutilisation de ce dispositif est autorise seulement aux deux conditions suivantes:

(1)il ne doit pas produire de brouillage et (2) lutilisateur du dispositif doit tre prt accepter tout brouillage radiolectrique reu, mme si ce brouillage est susceptible de compromettre le fonctionnement du dispositif. Note to users in the United States of America Notice:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Caution:

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Declaration of Conformity Product Name: Bluetooth Module Model Number: MBH7BTZ50 Responsible party: Fujitsu Components America, Inc. Address: 250 E. Caribbean Drive, Sunnyvale, CA 94089 U.S.A. Telephone number: 408-745-4900 This device complies with part 15 of FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. Note to users in Canada Note:

This Class B digital apparatus complies with Canadian ICES-003. Remarque concernant les utilisateurs au Canada Avertissement:

Cet appareil numrique de la classe B est conforme la norme NMB-003 du Canada. Note to users It is strictly forbidden to use antenna except designated. This equipment must not be co-located or operated in conjunction with any other antenna or transmitter. This equipment complies with FCC/IC radiation exposure limits set forth for uncontrolled equipment and meets the FCC radio frequency (RF) Exposure Guidelines in Supplement C to OET65 and RSS-102 of the IC radio frequency (RF) Exposure rules. This equipment should be installed and operated with at least 20cm more between the radiator and person's body(excluding extremities:hands, wrists, feet and ankles). Cet quipement est conforme aux limites dexposition aux rayonnements nonces pour un environnement non contrl et respecte les rgles dexposition aux frquences radiolectriques (RF) CNR-102 de lIC. Cet quipement met une nergie RF trs faible qui est considre conforme sans valuation de lexposition maximale autorise. Cependant, cet quipement doit tre install et utilis en gardant une distance de 20 cm ou plus entre le dispositif rayonnant et le corps ( lexception des extrmits : mains, poignets, pieds et chevilles). Note to users in Canada This device complies with RSS-Gen of IC Rules. Operation is subject to the following two conditions;

1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. Remarque concermant les utilisateurs au Canada Ce dispositif est conforme la norme CNR-Gen dIndustrie Canada. Lutilisation de ce dispositif est autorise seulement aux deux conditions suivantes:

(1)il ne doit pas produire de brouillage et (2) lutilisateur du dispositif doit tre prt accepter tout brouillage radiolectrique reu, mme si ce brouillage est susceptible de compromettre le fonctionnement du dispositif. Note to users in the United States of America Notice:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Caution:

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Declaration of Conformity Product Name: Bluetooth Module Model Number: MBH7BTZ53 Responsible party: Fujitsu Components America, Inc. Address: 250 E. Caribbean Drive, Sunnyvale, CA 94089 U.S.A. Telephone number: 408-745-4900 This device complies with part 15 of FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. Note to users in Canada Note:

This Class B digital apparatus complies with Canadian ICES-003. Remarque concernant les utilisateurs au Canada Avertissement:

Cet appareil numrique de la classe B est conforme la norme NMB-003 du Canada. Note to users It is strictly forbidden to use antenna except designated. This equipment must not be co-located or operated in conjunction with any other antenna or transmitter. This equipment complies with FCC/IC radiation exposure limits set forth for uncontrolled equipment and meets the FCC radio frequency (RF) Exposure Guidelines in Supplement C to OET65 and RSS-102 of the IC radio frequency (RF) Exposure rules. This equipment should be installed and operated with at least 20cm more between the radiator and person's body(excluding extremities:hands, wrists, feet and ankles). Cet quipement est conforme aux limites dexposition aux rayonnements nonces pour un environnement non contrl et respecte les rgles dexposition aux frquences radiolectriques (RF) CNR-102 de lIC. Cet quipement met une nergie RF trs faible qui est considre conforme sans valuation de lexposition maximale autorise. Cependant, cet quipement doit tre install et utilis en gardant une distance de 20 cm ou plus entre le dispositif rayonnant et le corps ( lexception des extrmits : mains, poignets, pieds et chevilles). Note to users in Canada This device complies with RSS-Gen of IC Rules. Operation is subject to the following two conditions;

1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. Remarque concermant les utilisateurs au Canada Ce dispositif est conforme la norme CNR-Gen dIndustrie Canada. Lutilisation de ce dispositif est autorise seulement aux deux conditions suivantes:

(1)il ne doit pas produire de brouillage et (2) lutilisateur du dispositif doit tre prt accepter tout brouillage radiolectrique reu, mme si ce brouillage est susceptible de compromettre le fonctionnement du dispositif.