FCC ID: SQK-FTP628WSL211A Mobile Printer

Mobile Printer FTP-628WSL210 Series User's Guide FUJITSU COMPONENT LIMITED IInnttrroodduuccttiioonn Thank you for purchasing the FTP-628WSL210 Series Mobile Printer

(hereafter referred to as this product). This User's Guide (hereafter referred to as this guide) contains precautions to use it safely and correctly. Before using this product, please be sure to read complete this guide to use it correctly. In addition, please keep this guide handy for future reference. If you have any suggestions or comments on this guide, please do not hesitate to let us know. Bluetooth is registered trademark of Bluetooth SIG.. Apple is registered trademark of Apple Inc., registered in the U.S. and other countries. iPhone and iPad are registered trademarks of Apple Inc. Android is trademarks of Google Inc. All other product names and servis names are trademarks or registered trademarks of their respective companies. All Rights Reserved, Copyright FUJITSU COMPONENT LIMITED 2012 1 PPrreeccaauuttiioonnss Change of contents The contents of this guide and this product are subject to change without notice for the improvement. Use to high safety application This product was designed and manufactured assuming general purpose use, such as standard industrial, general, personal and home use. This product was not designed and manufactured for a high safety application, that is, an application which demands extremely high safety and which may have a serious influence on society and expose individuals to serious danger if high safety is not assured (nuclear reaction control in a nuclear facility, aircraft automatic flight control, air traffic control, transport control in a mass transport system, medical equipment for life support, missile launch control of a weapons system), or an application which requires extremely high reliability (submarine relay, space satellite), Therefore do not use this product for a high safety application. If you are not certain whether this device is in a high safety application category, contact Fujitsu Component Ltd. sales personnel prior to use. We shall take no responsibility for any damage caused by the use of this product in a high safety application. Copyright This product and this guide are copyrighted works of FUJITSU COMPONENT LIMITED. This product and this manual must not be reproduced, duplicated, used, or modified, partially or in full, without permission. 2 Regulatory Compliance For Customers in USA (FCC) This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1) This device may not cause harmful interference, and 2) This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help. To assure continued compliance, any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate this equipment. (Example- use only shielded interface cables when connecting to computer or peripheral devices). 3 For Customers in CANADA (Industry Canada) This equipment complies with Industry Canada RSS210 rules. Operation is subject to the following two conditions:

1) This device may not cause harmful interference, and 2) this device must accept any interference received, including interference that may cause undesired operation. For Customers in EU (CE Marking) This product is in conformance with the requirements of European Council Directive:

R&TTE Directive 1995/5/EC Applied standards:

EN 60950-1 EN 300 328 EN 301 489-1 EN 301 489-17 Export Warranty This device may contain commodities, technology or software subject to export laws and regulations from the US and other countries. Diversion contrary to the country law is prohibited. We shall take no responsibility for any failure caused with wrong operation or wrong environment. Moreover, we cannot take responsibility of the loss, of the passive damages or of the claim of the third party, even if it is caused by using or breakdown of this product. In addition, the range of the guarantee of the failure of this product will never exceed the amount of money paid as a price of this product in any case. 4 SSaaffeettyy PPrreeccaauuttiioonnss Meaning of Symbols Caution Warning The following symbols are used in this guide. Please understand well the meaning of each symbol and read this guide. Indicates possibility of causing severe personal injury or death if not used properly. Indicates that a minor or some personal injury may occur or that the product itself or other users property may be damaged. Indicates danger, warning and caution. A concrete content is described on the side of this symbol. Indicates an action that must not be performed. A concrete content is described on the side of this symbol. Indicates an action that must be performed. A concrete content is described on the side of this symbol. Important Indicates important points by using this product. 5 Generic Precautions Warning in a hot

- Do not burn or heat. Failure to observe this may cause smoke or fire or breakdown.

- Do not pour water. This equipment is not waterproof. Failure to observe this may cause fire or burst or breakdown.

- Do not use or store the equipment environment. Failure to observe this may cause smoke or fire or breakdown.

- Do not throw or drop. Failure to observe this may cause fire or burst or breakdown.

- Do not use with wet hand. Do not drip or drop liquid such as drinking waters, clips or other foreign matter. Failure to observe this may cause fire or electric shock.

- In the event of the occurrence of heat or unusual smells or smoke or excessive noise during use, please stop using it immediately. Unplug the power cable, remove the battery and please sales representative or maintenance engineer.

- Do not use in locations of corrosive gas or salt wind. Failure to observe this may cause failure. contact your

- Do not modify or disassemble. Failure to observe this may cause fire or burst or breakdown. Fire Fire Fire Fire Fire Break-

down Break-

down Modify 6 Caution

- Do not use direct sun or dusty place that contains the oil and iron. Failure to observe this may cause heat, fire, or failure.

- If charging is not completed beyond the predetermined charging time, unplug the charger, please stop the charge. The battery may leak by overcharging.

- Do not apply force to the cable. Failure to observe this may cause fire or electric shock.

- Do not use while driving a vehicle or walking. Failure to observe this may cause traffic accidents and injuries caused by falls.

- Install the printer as far as possible from equipment having large radiation noise, such as a high voltage device and a large motor. Failure to observe this may cause malfunction or breakdown.

- Separate the power line from other devices which generate noise. (Large motor etc.) Failure to observe this may cause malfunction or breakdown.

- Before using this product, be sure to read complete user's guide to use it correctly. It may cause the failure by wrong use. Fire Fire Fire Injury Break-

down Break-

down Failure 7 Printer Warning Fire Accident Burn Burn

- Do not put metal objects or flammable objects into the gaps of the case. Failure to observe this may cause fire, or electric shock.

- Do not use the printer in a location that is prohibited the generation of radio waves. Might be in an accident by the malfunction of the instrument.

- Surely turn off the printer power and check that the printer head is sufficiently cooled down before cleaning. Failure to observe this may cause burn injury.

- During or immediately after operation, do not touch the print head and the support plate and the motor. Heat is not immediately discharged after the stop. Failure to observe this may cause burn injury. Caution

- Be careful not to get a hand or hair caught in moving part. Failure to observe this may cause burn injury.

- Never insert fingers or metal into the paper insertion and eject slots of the paper cutter. Failure to observe this may cause equipment failure or injury.

- When printing continuously at a rate high printing, head temperature warning may occur and printing may stop. Injury Injury Stop 8 Battery Fire Fire Fire Fire Fire Break-

down Modify Break-

down Break-

down Warning

- Do not use other than the specified battery. Failure to observe this may cause fire, or electric shock.

- Do not charge the battery in the charger other than the specified. Failure to observe this may cause fire, destruction.

- Do not short-circuit the electrode of the battery. Failure to observe this may cause heat, fire, destruction.

- Do not solder the terminal of battery. Failure to observe this may cause heat, fire, destruction.

- Do not make impact or pressure. Failure to observe this may cause heat, fire, destruction.

- Do not use the battery for another device or purpose. Failure to observe this may cause destruction.

- Do not disassemble the battery. Failure to observe this may cause heat, fire, destruction. Caution

- Turn off the power of printer before the battery removed. Failure to observe this may cause destruction.

- If you do not want to use for a long time, remove the battery from the body to store printer. Failure to observe this may cause deterioration of the battery and over-discharge state. 9 AC Adaptor Warning

- Do not connect other than the specified voltage or/and frequency. Failure to observe this may cause fire or electric shock due to cable disconnection.

- Do not use other than the specified AC adaptor. Failure to observe this may cause heat, fire, or destruction.

- Do not use the AC adaptor for another device or purpose. Failure to observe this may cause damaging printer or/and battery. Caution

- Please connect or remove the AC adaptor after the power is turned off. Failure to observe this may cause breakdown.

- If you do not want to be used for a long time, please keep the power cable is unplugged. Failure to observe this may cause electric shock or fire due to dust and moisture. Fire Fire Break-

down Fire Break-

down 10 Warning Label of Product This product is stuck label on the following alarm displays. This label must not peel off or erase the displays. Moreover, please contact the distributor when becoming difficult to see the display due to dirt etc. Warning display Contents HEAD GEAR, HOOK Since the print head and its support plate get a high temperature during printing, do not touch them directly. Pay attention to fingers and hairs not to be caught in the moving part such as a gear or hook because it may cause an injury. CAUTION Please do not touch the cutter blade when you exchange the roll paper because it may cause an injury by the contact of the blade. 11 TTaabbllee ooff CCoonntteennttss 1 Kinds of Product..............................................................13 2 Preparation to print .........................................................14 2.1 Packing item ...........................................................14 2.2 Option Items...........................................................15 2.3 Part Names.............................................................16 2.4 Inserting the Battery................................................19 2.5 Connecting AC Adaptor(Charging)..............................20 2.6 Connecting AC Adaptor(Operating) ............................21 2.7 Setting Paper...........................................................22 2.8 Setting Belt Fixture ..................................................23 3 Operating Procedures ......................................................24 3.1 Turning On..............................................................24 3.2 Test Print ................................................................25 3.3 USB Communication.................................................27 3.4 Bluetooth Communication.........................................28 3.5 Printer Error............................................................29 4 Indicator Lights...............................................................31 4.1 Normal Operation ....................................................31 4.2 Printer Error............................................................32 4.3 Charging.................................................................33 4.4 Maintenance Mode ...................................................33 5 Maintenance...................................................................34 5.1 Thermal Head .........................................................34 5.2 Platen Roller............................................................35 5.3 Paper Sensor...........................................................35 5.4 Paper Cover ............................................................36 5.5 POWER/FEED Switch................................................37 6 Troubleshooting ..............................................................38 7 Specifications .................................................................42 7.1 Printer specifications ................................................42 7.2 Paper specifications..................................................43 8 Recycle..........................................................................44 9 Appendix .......................................................................45 9.1 Product Support ......................................................45 9.2 Bluetooth Communication.........................................46 12 11 KKiinnddss ooff PPrroodduucctt 1 Kinds of Product There are the following kinds of the product. Please note that the printer may not support the function by the printer model, even if there is a description in this guide. MODEL NAME F TP-628WSL210#20-R a : Supply item

(Refer to Table 1-1) b : Interface

(Refer to Table 1-2) Table 1-1. Supply items Contents Printer Battery 20 AC Adaptor AC Cable Belt Fixture Table 1-2. Interface Contents 10 11 12 Bluetooth Bluetooth

(iOS supported) USB 13 2 Preparation to print 22 PPrreeppaarraattiioonn ttoo pprriinntt 2.1 Packing item The following are attached to this product. Please open the box and confirm to item in the box. If it is insufficient, please ask the distributor. Printer Battery AC adaptor Precautions Guide 14 2 Preparation to print 2.2 Option Items To use this product better, the following and optional parts are prepared. Please confirm how to buy to the Acquisition origin of this product. Paper Battery AC adaptor AC cable

(PSE or UL/CSA) USB cable Belt Fixture 15 2 Preparation to print 2 1 2.3 Part Names Front Side (Cover Close) 4 3 5 6 7 8 1 2 3 4 5 6 7 8 Paper Cover Paper Cutter Status LED POWER Switch FEED Switch Cover Open Lever USB Connector Battery Cover

: This is opened and paper is set.

: To cut paper.

: The state of printer is displayed.

: To turn the power supply on or off.

: To feed paper.

: To open the cover.

: This is opened and it connects PC etc.

: This is opened and the battery is set. 16 2 Preparation to print 9 Front Side (Cover Open) 10 9 10 Platen Roller Warning Label

: To feed paper.

: This shows warning when using printer. 12 11 11 12 Thermal Head Paper Sensor

: This applies heat to paper.

: This sensor detects the state of paper. 17 2 Preparation to print Rear Side 13 14 15 13 14 15 Screw for Belt Fixture : This fixes Belt Fixture. AC Adaptor Connector : This is opened and AC adaptor is connected. Product Label

: Printer Type and etc are displayed. 18 2.4 Inserting the Battery 2 Preparation to print Caution Life of the battery charging is about 500 times. (At the normal temperature) If the degradation battery is used, not only the equipment malfunctions but also destruction might be caused. 1. Please open the battery cover by pushing the lock of the battery cover and pulling the cover forward. 2. Please turn the label surface of the battery below and insert the surface of the electrode. 3. Please hook the lock of the battery cover to the battery insertion entrance and close the cover. Battery cover Cover lock Battery 19 2 Preparation to print 2.5 Connecting AC Adaptor(Charging) The battery is charged by the charger capability with built-in this printer. Caution Please stop charging at once if an abnormal charge is generated. 1. Please connect the AC cable with the AC adaptor, and connect the AC plug with the outlet. 2. Please open the connector cover for the AC adaptor, and connect the DC output terminal of the AC adaptor with the connector for the AC adaptor. AC adaptor AC cable Connector for AC adaptor Cover

[Side view]

3. When the charge starts, the LED becomes lighting red, and when the battery becomes a full charge, the LED is turned off. Please refer to chapter 4.3 for the LED display of charging status. 4. Please close the battery cover by hanging the hook of cover, and pushing the center of cover. Important charge. When the printer power supply is turned on, it is not able to 20 2 Preparation to print 2.6 Connecting AC Adaptor(Operating) This product can be operated also with the AC adaptor. 1. Please connect the AC cable with the AC adaptor, and connect the AC plug with the outlet. 2. Please open the connector cover for the AC adaptor, and connect the DC output terminal of the AC adaptor with the connector for the AC adaptor. AC cable AC adaptor Connector for AC adaptor Cover

[Side view]

3. Please turn on the power supply of the printer. Please refer to chapter 3.1 for how to turn on the power supply. Important

- The battery must be putted in the printer though it operates with only the AC adaptor.

- When the power supply is turning off, it is possible to charge it. When the power supply is turning on, it is not possible to charge it. 21 Cover Open Lever Thermal Paper

(Thermosensitive Side) 2 Preparation to print 2.7 Setting Paper 1. Please open the paper cover by pushing the cover open lever in the direction of the arrow and going up. 2. Please set the paper in the printer. 3. Please put out the edge of the paper and close the paper cover. Please push the center of the paper cover firmly when closing. 22 2 Preparation to print 2.8 Setting Belt Fixture The printer can be attached to the waist belt with belt fixture of optional parts. The belt fixture is recommended to be attached with the following directions. How to attach it 1. Please remove the screw for the belt fixture on the printer bottom surface. 2. Please tighten the screw for the belt fixture after disposing it in the direction of the favorite. Important it correctly. different depending on the direction of the installation.

- If the belt fixture runs aground in the stopper, it cannot install to

- There are two tapped holes in the belt fixture. The hole used is 23 3 Operating Procedures 33 OOppeerraattiinngg PPrroocceedduurreess 3.1 Turning On 1. Please keep pushing the POWER Switch until lighting to green the State LED. 2. It is possible to turn off power by keeping pushing the POWER Switch until the State LED is turned off. 24 3 Operating Procedures 3.2 Test Print This product has the test print function. The setting of the printer can be confirmed in this test print. 1. Please turn off the power and push the FEED switch. 2. Please turn on power with the FEED switch pushed. Then, the test print starts. 3. When the test print ends, the printer automatically turns off the power supply. 4. Please turn off power when you want to stop the test print. 5. Please refer to the next page for the content of the test print. (The content of the test print is different depending on the model) Important It does not execute the test print in the state of the printer error like the paper end or the paper cover open, etc. Please execute it after releasing the state of the error. 25 3 Operating Procedures Checked pattern The thermal head open circuit etc. can be confirmed. Version The firmware version can be confirmed. Setting information etc The setting information etc can be confirmed. This print example is the following content.

- Printer serial number

- Printer ID

- Firmware sam value

- Auto power off transition duration

- Auto power down transition duration Voltage and Temperature The power voltage and the temperature of thermal head can be confirmed. Interface Available interface and protocol can be confirmed. Bluetooth information The Bluetooth information can be confirmed. Installing font Installing font can be confirmed.

628AD Ver 1.00

Serial No : 22000001 Printer ID : 01 PrinterSUM : 00000001 Power OFF : 30 min Power Down : 1.0 sec HD VOLT: 5.0 V HD TEMP: 25 C INTERFACE : Bluetooth/USB HAND SHAKE : Non process BT FIRM: 0000D1000000000437 BD ADDR: 00 11 22 33 44 55 BT NAME: 628WSL210_000001 BT LINK: 0 sec

!"#$%&'()*+,-./0123456789:;<=>?

@ABCDEFGHIJKLMNOPQRSTUVWXYZ[\]^_

'abcdefghijklmnopqrstuvwxyz{|}~

!"#$%&'()*+,-./0123456789:;<=>?@ABCDEFGHIJKLMNO PQRSTUVWXYZ[\]^_'abcdefghijklmnopqrstuvwxyz{|}~

26 3 Operating Procedures 3.3 USB Communication It explains the example of the connection method in the USB communication to print it from the terminal like a personal computer as follows. 1. Please prepare the USB cable. The plug on the printer side (device side) is mini B type. 2. Please open the USB connecter cover and connect the plug of cable to the USB connector. 3. Please connect the plug of host side to the host terminal connecter. 4. Please start the application in the host terminal (The communication port is opened). Then, the display of the Status LED becomes the state of the USB connecting. Important When other interfaces connect it, it is not possible to connect it. 27 3 Operating Procedures 3.4 Bluetooth Communication It explains the example of the connection method in the Bluetooth communication to print it from the terminal like a personal computer as follows. 1. Please turn on the power of printer. 2. Please search the Bluetooth device by the application in the host terminal. 3. The device name of the connected printer is displayed. Then, please select the device and connect it. 4. Please input "9999" when the PIN code is demanded.

(At the setting of the state of the factory shipment) 5. The display of the Status LED becomes the state of the Bluetooth connecting. Important

- There is a product that does not supporting to this communication. Please refer to the C.1 for the supporting product. tablet PC.

- Please refer to chapter 9.2 for the connection with a general

- When other interfaces connect it, it is not possible to connect it. 28 3 Operating Procedures 3.5 Printer Error The error occurs when the printer cannot print/work normally. The category of error is notified by the LED and the communication when the error is occurring. Please return to normally status by removing the cause when the error is occurring. The following example explains the cause and way to release of each error. Error Paper End Paper Cover Open Thermal Head Temperature Error Cause Solution

- There is no paper in the paper cover.

- It is not correctly set though there is a paper

- Garbage has collected on the paper sensor.

- The paper cover is open.

- The thermal head is high temperature.

- Please clean the paper to

- Please correctly set paper referring to chapter 2.7. sensor referring chapter 5.3.

- Please correctly close the paper cover referring to chapter 2.7.

- Please do not print it for a while. The temperature of the thermal head falls and it returns from the error. Important

- It is not abnormal operation that the temperature goes up because this printer is printing it by heating the temperature of the thermal head.

- The Thermal Head Temperature Error is generated easily by the high ambient temperature. 29 3 Operating Procedures Error Supply Voltage Error Mark Undetection Cause

- The residual quantity of the battery has decreased.

- The AC adaptor is out of order. (At the AC adaptor operation)

- The mark of paper is not correctly printed.

- Garbage has collected in the paper sensor.

- The printer is out of order. Hardware Error MCU Operation Error RAM Error Bluetooth Error Charge Error Solution

- Please charge

- Please exchange the battery. the AC adaptor.

- Please use the paper on which the mark is correctly printed.

- Please clean the paper sensor referring to chapter 5.3.

- Please send this printer to the repair. The battery is out of order. The AC adaptor used for the charge is out of order. The control board of the printer is out of order.

- Please exchange

- Please exchange

- Please send the battery. the AC adaptor. this printer to the repair. Important When Supply Voltage Error or Low Battery is generated at once after full charging, this battery may be deteriorating. Please stop the use of this battery, and exchange it for a new battery. 30 44 IInnddiiccaattoorr LLiigghhttss 4 Indicator Lights The state of the printer error and the battery residual quantity is confirmed by the LED display. Important It may be difficult to see the LED display in a bright place under direct sunshine etc. 4.1 Normal Operation Printer Status Standby USB Connecting Bluetooth Connecting Power Off Low Battery LED Indications (LED Symbol:Lighting, :Blinking) Green Orange Red Blink Cycle(Unit [msec]) 1time 1000 125 125 ON OFF 2times 3times ON OFF ON OFF ON OFF ON OFF 125 125 250 1000 125 125 125 250 250 1000 1000 Power off 500 500 Green Red 500 500 Green Red 31 4 Indicator Lights 4.2 Printer Error Printer Status LED Indications (LED Symbol:Lighting, :Blinking) Green Orange Red Blink Cycle(Unit [msec]) 1000 125 125 125 250 125 125 125 250 250 125 125 250 125 125 250 125 125 250 125 125 250 125 125 250 Blink 4 times Blink 5 times Blink 6 times Blink 7 times Blink 8 times 1000 1000 125 125 125 125 125 1000 1000 1000 1000 1000 Paper End Paper Cover Open Thermal Head Temperature Error Supply Voltage Error Hardware Error Mark Undetection MCU Operation Error /

RAM Error Bluetooth Error 1time 2times 3times 4times 5times 6times 7times 8times ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF 32 4.3 Charging 4 Indicator Lights LED Indications (LED Symbol:Lighting, :Blinking) Green Orange Red Blink Cycle(Unit [msec]) Printer Status Chargeing Full Charge ON OFF ON OFF Charging Charging Full charge 950 950 Charge Error

(Over charge, Over discharge, Over time) 4.4 Maintenance Mode ON OFF LED Indications (LED Symbol:Lighting, :Blinking) Green Orange Red Blink Cycle(Unit [msec]) 1time ON OFF 125 Red 1000 Orange Printer Status Printer Firmware Downloading 33 5 Maintenance 55 MMaaiinntteennaannccee Please maintain this printer regularly. Caution battery or connecting the AC adaptor. explaining in this chapter.

- Do not do the maintenance task for the printer with including the

- Do not absolutely maintain, disassemble and repair the part not 5.1 Thermal Head Please maintain the thermal head once a month. 1. Please open the paper cover. (Refer to chapter 2.7) 2. Alcohol is soaked into the soft one such as cotton buds, and it wipes it gently until the thermal head is cleaned. Please use IPA on the market for alcohol. (Isopropyl alcohol) 3. Please wipe off with a cloth that dries and is soft, and please close the paper cover after it waits until naturally drying. 34 5 Maintenance 5.2 Platen Roller Please maintain the platen roller once a month. 1. Please open the paper cover. (Refer to chapter 2.7) 2. Alcohol is soaked into the soft one such as cotton buds, and it wipes it gently until the thermal head is cleaned. Please use IPA on the market for alcohol. (Isopropyl alcohol) 3. Please wipe off with a cloth that dries and is soft, and please close the paper cover after it waits until naturally drying. 5.3 Paper Sensor Please maintain the paper sensor once a month. 1. Please open the paper cover. (Refer to chapter 2.7) 2. Please remove the dust garbage with a soft nylon brush etc. Important The paper sensor is an optical sensor. This lens might scar by strongly rubbed. As a result the printer might become to not detect the paper correctly. 35 5 Maintenance 5.4 Paper Cover If the paper cover came off, please repair according to the following procedures. 1. Please push the opening and closing fulcrum of the paper cover to the printer with the paper cover opened, and it connects the printer. Opening and closing fulcrum 2. Please confirm the correct connection by opening and of paper cover closing the paper cover 2-3 times. 36 5 Maintenance 5.5 POWER/FEED Switch If the Power switch or the FEED switch came off, please repair according to the following procedures. 1. Please push and fix the switch to be suitable for a quadrangle on the switch side and for hole of the case side. Please fix the FEED switch to be suitable of the oval. Switch

[Front view]

2. Please confirm that the repaired switch works correctly.

[Side view]

37 6 Troubleshooting 66 TTrroouubblleesshhoooottiinngg Power Problem Cause Is there a battery? or Isn't it reversed?

Is the battery charged enough?

Is the POWER Switch correctly pushed?

Is the battery old?

Is there a battery? or Isn't it reversed?

Is the battery old?

Is the AC adaptor correctly connected?

Have the battery already been a full charge?

Is not the power turned on? It is not possible to charge, when the power is turned on. Is not the printer used at an incorrect ambient temperature?

Is not auto power off set?

(C. 3.2) Isn't the remainder of the battery a little?

Does not the error occur?

(C. 4) Is the battery old?

Printer does not turn on Battery does not be charged or Charge error occurs Power supply cuts suddenly Battery discharge early 38 Solution Please set the battery correctly. (C. 2.4) Please charge the battery. (C. 2.5) Please push the POWER Switch correctly. (C. 3.1) Please exchange it to new battery. Please set the battery correctly. (C. 2.4) Please exchange it to new battery. Please connect the AC adaptor correctly.

(C. 2.5) The charge is unnecessary. Please turn off the power. (C. 3.1) Please charge it at a correct ambient temperature. (C. 7.1) Auto power off can be set by the command. Please charge the battery. (C. 2.5) Please treat it according to each error. (C. 3.5) Please exchange it to new battery. Communication Problem Cause Printer does not communicate Printer does not communicate

(with USB) Printer does not communicate

(with Bluetooth) Is not the power turned off?

Is the application or the driver for this product used?

Is USB cable correctly connected?

Does not USB cable have the breakdown of the open circuit etc?

Is not Bluetooth connected?

Is USB COM driver correctly installed?

Is the link correctly connected?

Is not USB connected?

Does the transmitter correspond to the SPP profile?

Isn't there equipment that causes the radio interference to be near?

Isn't there shield that interfere the radio between the transmitter and the printer?

6 Troubleshooting Solution Please turn on the power. (C. 3.1) Please use the application or the driver for this product. Please connect the cable correctly.

(C. 3.3) Please use the cable without the breakdown. Please communicate USB after cutting Bluetooth. Please install the COM driver correctly. Please connect the link correctly. (C. 3.4) Please connect Bluetooth linking after cutting USB. Please use the transmitter corresponding to the SPP profile. Please stop the device that causes the radio interference or keep away the transmitter and the printer from the device. Please use it in the place without the shield. 39 6 Troubleshooting Print Problem Cause Printer does not paper feed or Paper jam occurrs Printer does not print Print is so light or Print is smudging Is not the power turned off?

Is the paper correctly set?

Is the paper cover closed?

Does not the printer error occur? (C. 4) Isn't the platen roller dirty?

Is not the power turned off?

Is the paper correctly set?

Is the paper cover closed?

Does not the printer error occur? (C. 4) Isn't the platen roller dirty?

Is the paper correctly set?

Is the paper cover closed?

Isn't the platen roller dirty?

Is a correct paper used?

Is the battery old?

40 Solution Please turn on the power. (C. 3.1) Please set the paper correctly. (C. 2.7) Please close the paper cover firmly. (C. 2.7) Please recover the printer error. (C. 3.5) Please clean the platen roller. (C. 5.2) Please turn on the power. (C. 3.1) Please set the paper correctly. (C. 2.7) Please close the paper cover firmly. (C. 2.7) Please recover the printer error. (C. 3.5) Please clean the platen roller. (C. 5.1) Please set the paper correctly. (C. 3.1) Please close the paper cover firmly. (C. 2.7) Please clean the platen roller. (C. 5.1) Please use a correct paper. (C. 7.2) Please exchange it to new battery. Others Problem Print starting location is incorrect Printing is slow Paper cover does not open or close 6 Troubleshooting Cause Does the mark detection operate correctly?

(C. 4.2) Isn't the remainder of the battery a little?

Is the battery old?

Is not the print of many blacks printed?

Isn't the ambient temperature low?

Does not the paper cover come off?

Solution Please remove the cause of the mark detection error.

(C. 3.5) Please charge the battery. (C. 2.5) Please exchange it to new battery. It is not a breakdown though the print slows when there are many blacks. It is not a breakdown though the print slows when the ambient temperature is low. Please set the paper cover.

- Please consult a technical support when not solving it by these

- In parentheses (C. **) in the table, it indicates a chapter number of Important methods. the relevant. 41 7 Specifications 77 SSppeecciiffiiccaattiioonnss 7.1 Printer specifications Items Print Method Resolution Dimensions Weight Max Print Width Print Speed Character Barcode Interface Conformity Standerds Operating Temperature Contents Thermal Line-dot Printing 8dot/mm203dpi 84136.543.6mm About 220g Including a battery, Excluding a paper About 48mm Max 40mm/sec Battery full charge, Print ratio 12.5%

Alphanumeric, Katakana Kanji UPC-A, UPC-E, JAN13(EAN13), JAN8(EAN8), CODE39, ITF, CODABAR, CODE128, GS1 DataBar, QR code, MAXI code, PDF417 USB,Bluetooth (Depends on model) TELEC, VCCI, FCC, IC, CE marking

: 8x16, 16x16, 12x24, 24x24

: 16x16, 24x24 0 to 50 deg C 5 to 40 deg C (Print Quality assurance) 0 to 40 deg C (with AC adaptor) Operating umidity 30 to 85%RH (no dew condensation) Storage Temperature Storage Humidity 5 to 90%RH (no dew condensation)

-20 to 60 deg C 42 7.2 Paper specifications 7 Specifications Contents Thermal Roll Paper 58+0 Up to 36mm

-1mm 8mm or more Items Type Type Widht Outer Diameter Inner Diameter Thickness 60 to 80m Specified Paper Long Term Storage Important Name Manufacture High Sensitive TF50KS-E4 Nippon Paper Group Standard Paper TF60KS-E Nippon Paper Group Medium Term Storage PD150R TP60KS-F1 Nippon Paper Group PD170R Oji Paper Group P220VBB-1 Mitsubishi Paper Oji Paper Group HA220AA Mitsubishi Paper Mills Limited Mills Limited sun-light. Thermal paper will get colored due to chemical reaction. When handling it, pay attention to the following points:

Do not store it at high-temperature, high-humidity place. Do not store for a long time at a place exposed to direct Do not use solvent type glue for pasting. Do not let it get in touch with plastic film containing plasticiser Do not stick it together with diazotype copying paper. Do not wet and scratch. for a long time. 43 8 Recycle 88 RReeccyyccllee This symbol means:

Do not dispose of this product together with your household waste!

Please refer to the information of your local community or contact our dealers regrading the proper handling of end-of-life electric and electronic equipments. Recycling of this product will help to conserve natural resources and prevent potential negative consequences for the environment and human health caused by inappropriate waste handling. 44 9 Appendix 99 AAppppeennddiixx 9.1 Product Support If you have the question on the product, please inquire of the distributor or the following. Moreover, when you request the breakdown and the repair, please tell us the model name and the product serial number in addition to information on the symptom etc. Technical Support Section FUJITSU COMPONENT LIMITED (Japan) Global Marketing Dept.2 Tel: +81-3-5449-7014 Fax: +81-3-5449-2628 E-mail: promothq@fcl.fujitsu.com 45 9 Appendix 9.2 Bluetooth Communication

(1) Android Terminal 1. Please turn on the power of printer. 2. Please open "Settings" - " WIRELESS NETWORKS"

from the menu of terminal, and turn on Bluetooth. 3. Please open the "Bluetooth, and tap "FTP-628WSL".

(Please tap "SEARCH FOR DEVICES", if it does not appear) 4 Please input the PIN code, and tap "OK". PIN code is "9999" in the state of the factory shipment.

(The PIN code input is unnecessary at the connection of second and subsequent) 5. When the connection with the printer succeeds, it is displayed in "FTP-628WS" in "PAIRED DEVICES". 6. Please connect and print by using the application. 46

(2) iOS Terminal 1. Please turn on the power of printer. 2. Please open "Settings" - "General" - "Bluetooth" from 9 Appendix the menu of terminal, and turn on Bluetooth. 3. Please tap "FTP-628WS" from "Devices". 4. Please input the PIN code, and tap "Pair". PIN code is "9999" in the state of the factory shipment.

(The PIN code input is unnecessary at the connection of second and subsequent) 5. When the connection with the printer succeeds,

"Connected" is displayed to "FTP-628WS". 6. Please connect and print by using the application. 47 MMEEMMOO Mobile Printer FTP-628WSL210 Series User's Guide L0NA02265-L11802RS Pablished by FUJITSU COMPONENT LIMITED Aug, 2012 Rev 1