FCC ID: AZPT10J-24G Radio Control

 

Common function The setting screens are called from the following menu. All the functions common to airplane, helicopter, glider, and multi-copter model types are shown here. First set the throttle to slow. Then turn on the power. Home screen To menu screen by holding down the + key When the END key is pressed, the display returns to the home screen. END MENU MENU 1/3 MENU 2/3 MENU 3/3

1

12

123

1 2 3

C o m m o n f u n c t i o n 38 1 second When the + key is pressed for 1 second, the menu screen is displayed. Selection M o v e t h e c u r s o r

(highlighted) up and down and to the left and right with the Jog key and select the function. The cursor can be moved over several pages. Calling the setting screen Press the Jog key to open the setting screen. key LCD key key END key Jog key MENU2/3 TELEMETRY

(P.66) Telemetry Display Alarm setup

(P.83) SENSOR Telemetry sensor SBUS LINK

(P.89) S.BUS servo set up MDL-TRANS

(P.92) Data transfer of another 10J or 8J TRAINER

(P.93) Trainer Function MENU1/3 MDL-SEL

(P.40) Model select Model Copy Data reset RX Link

(P.43) MDL-NAME Model name User name FAIL SAFE

(P.45) Fail safe

(P.47) REVERSE Servo reverse TIMER

(P.48) Timer

(P.49) SERVO Servo monitor Servo test END POINT

(P.50) End point

(P.51) TRIM Trim reset Trim step SUB TRIM

(P.52) Sub trim

(P.53) P.MIX1-6 Program mixing 1 6 AUX-CHAN

(P.56) AUX channel PARAMETER

(P.58) Data reset Model type ATL-

trim LCD contrast Back light :

mode, time, adjustment Home display Battery alarm Battery vibration Buzzer tone Jog navi Jog light Jog time Telemetry : mode, unit Speech :

language, volume Stick position alarm C o m m o n f u n c t i o n 39 MDL-SEL Model selectselect copy reset RX type link Function This function is used when calling and copying model data stored in the transmitter. The selected model data can also be reset. System changes

(T-FHSS Air, S-FHSS) matched to the receiver type and linking with the receiver are also done here.

(Common) Model selectSELECT The model data of up to 30 models can be stored in the transmitter. This function is used when calling saved model data. Model copyCOPY This is the model data copy function. It is convenient when you want to store model data as backup or build a number of models with the same data settings. The data of the model memory currently in use can be copied to another model memory. Data reset RESET The model data currently in use can be reset to its initial value. However, it does not Reset other than the following of a parameter.

[ The function reset in a parameter : ATL trim, TELEMETRY mode, STK POSI ALRM ]

Receiver selectionRX The R3008SB supplied with the transmitter, employs the T-FHSS Air system. When you want to use an S-FHSS receiver, switch to S-FHSS here. However, the telemetry function cannot be used with the S-FHSS system. LinkLINK When linking with the receiver, the transmitter is set to the link mode here. The ID number of the currently linked receiver is displayed. Method C o m m o n f u n c t i o n Calling the setting screen Call the menu screen from the home screen by pressing the + key for 1 second. 1 second

"MDL-SEL"

Select from the menu with the Jog key. Open the setting screen by pressing the Jog key. MDL-SEL

XXXXXXXXX Model number1 30 Original data : Model type Copy place : Model type Model SystemT-FHSS Air or S-FHSS) Link receiver ID Model name name Model select Model copy Data reset RX system Link Select the setting item with the Jog key. 40 Model select Select the SELECT item and then select the model number by pressing the + key or key. or Selection range1 30 Press the Jog key for 1 second. Select the model by pressing the Jog key. 1 second Conrmation message

"sure?" blinks. A confirmation "beep beep" sounds to show that selection is complete. For safety, a double setting system is used. When a change is cancelled after the confirmation message is displayed, the change is not made when moved to another setting item by Jog key. Model copy Select the COPY item and the select the model number of the copy destination by pressing the + key or key. or Selection range1 30 Press the Jog key for 1 second. Copy the model by pressing the Jog key. 1 second Conrmation message

"sure?" blinks. A confirmation "beep"

sounds and "COMPLETE"

is displayed on the screen to show that copying is complete. For safety, a double setting system is used. When a change is cancelled after the confirmation message is displayed, the change is not made when moved to another setting item by Jog key. Date reset key for 1 second. Select the REST item and then press the Jog Date reset by pressing the Jog key. 1 second Conrmation message "sure?" blinks. A confirmation "beep" sounds and

"COMPLETE" is displayed on the screen is complete. For safety, a double setting system is used. When a change is cancelled after the conrmation message is displayed, the change is not made when moved to another setting item by Jog key. CAUTION Only the throttle channel (CH3) initial setting is REV (reverse). Thoroughly check the Hi and Low directions of the engine or motor used and be careful that they do not suddenly run at full speed.Even after data reset, CH3 is reversed. C o m m o n f u n c t i o n 41 RX type Select the RX item and then select T-FHSS Air or S-FHSS by pressing the + key or key. or Selection rangeT-FHSS Air, S-FHSS Conrmation message

"sure?" blinks. RX type change by pressing the Jog key. A confirmation "beep"

sounds is complete. For safety, a double setting system is used. When a change is cancelled after the confirmation message is displayed, the change is not made when moved to another setting item by Jog key. Link for 1 second. Select the LINK item and then press the Jog key 1 second T-FHSS Air only. S-FHSS does not enter the link mode. Use the receiver link button to link the receiver. Enters the link mode for about 20 seconds. During this time, bring the receiver near the transmitter and turn on the receiver power. When linking, the receiver ID is displayed. In the link mode, a confirmation "beep beep beep" sounds and the time remaining is displayed on the screen. When 20 seconds have elapsed, a continuous beep sounds and the link mode is exited. For safety, linking must not be performed while the drive motor or engine is running. When linking is complete, turn the power o and on and check operation. C o m m o n f u n c t i o n 42 MDL-NAME Model name User name Function A model name is inputted into each model in T10J. User name is inputted into T10J.

(Common) Model name settingMDL NAME This function assigns a name to the model data. The model name is displayed on the top row of the home screen. This serves to prevent model memory mistakes if the current aircraft name or other name is entered. Up to 10 characters can be set. User name settingUSR NAME The user name displayed on the home screen can be set. (When a user name is not set, the Futaba logo is displayed) When the home screen display is changed to USR-NAME by PARAMETER, the set user name is displayed on the home screen. Up to 10 characters can be set. Method Calling the setting screen Call the menu screen from the home screen by pressing the + key for 1 second. 1 second

"MDL-NAME"

Select from the menu with the Jog key. Open the setting screen by pressing the Jog key. MDL-NAME Reset Model name User name Model name Move the cursor to the model name digit you want to change by pressing the + key or key. or Candidate characters Characters that can be entered ;

Numeric/upper case alphabet/

lower case alphabet Move the cursor to the candidate character you want to change with the Jog key. Change the character by pressing the Jog key. Set the model name by repeating steps to above. Reset methodWhen the cursor is moved to any digit of the model name by + key or key and the Jog key is pressed in the state in which the cursor was moved to RESET by Jog key, the model name returns to its initial setting. C o m m o n f u n c t i o n 43 User name Move the cursor to the user name digit you want to change by pressing the + key or key. or Move the cursor to the candidate character you want to change with the Jog key. Change the character by pressing the Jog key. Set the user name by repeating steps to above. Reset method: When the cursor is moved to any digit of the user name by + key or key and the Jog key is pressed in the state in which the cursor was moved to RESET by Jog key, the user name returns to its initial setting (Futaba logo). Displaying the user name on the home screen The set user name can be displayed on the home screen. (When a user name is not set, the Futaba logo is displayed.) When the home screen display is changed to USR-NAME by PARAMETER, the set user name is displayed. C o m m o n f u n c t i o n Calling the setting screen Call the menu screen from the home screen by pressing the + key for 1 second. 1 second

"PARAMETER"

Select from the menu with the Jog key. Open the setting screen by pressing the Jog key. Parameter Select "HOME-DSP" from the parameter 2 page with the Jog key. Select "USR-NAME" by pressing the + key or key. End setting by pressing the END key. END 44 FAIL SAFE Fail safe Function When normal radiowaves cannot be received due to noise and interference, the NOR mode, which holds the servo of each channel in its position immediately before reception was lost, or F/S (Fail Safe) mode, which moves the servo of each channel to a preset position, can be selected. When T-FHSS Air is selected, the battery fail safe voltage can be set.

Method Calling the setting screen Call the menu screen from the home screen by pressing the + key for 1 second. 1 second

(Common)

Reset methodThe battery fail safe function can be temporarily disabled by moving the throttle stick to the slowest side. However, after 30 seconds the battery fail safe function will return to the battery fail safe state. WARNING For safety, always set the fail safe functions.

the servo moves to the maximum slow side for airplanes and to the slow side from the hovering position for helicopters. Crashing of the model at full high when normal radio waves cannot be received due to interference, etc., is very dangerous.

be mistaken for an engine malfunction and will be reset at

any doubts, immediately land.

"Fail safe"

Select from the menu with the Jog key. Open the setting screen by pressing the Jog key. F/S Position Mode select Select the setting item with the Jog key. FAIL SAFE 1 2 3 TFHSS B-F/S : ON/OFF MODE. POSI B-F/S 1: AIL 2: ELE 3: THR 4: RUD 5: GER

NOR

20% ACT Fail safe Mode selection Select the mode by pressing the + key or key at the MODE item of each channel. or Range NOR, F/S When F/S mode was selected F/S position In the mode selected state, set the F/

S position by holding the stick of that channel in the position you want to set and press the Jog key for 1 second. A conrmation beeping sounds to show that the servo position was set. When using the B-F/S mode Select ACT by pressing the + key or key at the B-F/S item. or Range Default INH, ACT INH C o m m o n f u n c t i o n 45 Battery fail safe voltage setting Select BATTERY F/S VOLTAGE on page 3 of the fail safe screen with the Jog key. S e t t h e v o l t a g e b y pressing the + key or key. End setting by pressing the END key. END Set up range 3.8V 4.0V 4.2V 4.4V 4.6V 4.8V 5.0V 5.3V 5.6V 5.9V 6.2V 6.5V 6.8V 7.1V 7.4V C o m m o n f u n c t i o n 46 REVERSE Servo reverse Function Servo reversing (REVERSE): changes the direction an individual servo responds to a

For CCPM helicopters, be sure to read the section on SWASH AFR before reversing any servos. With the exception of CCPM helicopters, always

(Common) complete your servo reversing prior to any other programming. When using ACRO functions that control

may be confusing to determine whether the servo needs to be reversed or a setting in the function needs to be reversed. Refer to the instructions for each specialized function for further details. CAUTION Only the throttle channel (CH3) initial setting is REV (reverse). Thoroughly check the Hi and Low directions of the engine or motor used and be careful that they do not suddenly run at full speed. Since the direction of the ailerons of an airplane can be easily mistaken, be very careful. Method Calling the setting screen Call the menu screen from the home screen by pressing the + key for 1 second. 1 second

"REVERSE"

Select from the menu with the Jog key. Open the setting screen by pressing the Jog key. To prevent erroneous setting, after the servo reverse screen was called as described above, the channel will not be selected if the Jog key is not pressed at the left and right. Channel select Select the channel with the Jog key. Servo Reverse Channel is Select by Jog key. REVERSE E L E A I L REV NOR T H R R U D G E R F L P A U X A U X A U X A U X 1 2 3 4 5 6 7 8 9 10 The currently selected channel is highlighted. Display Reverse/Normal REVReverse NORNormal Channel number NOR or REV is chosen by Jog key. Reverse the servo by pressing the Jog key. Selection range1 10ch The confirmation message "sure?"

blinks on the screen. (Not displayed if the same as before.) A confirmation beeping sounds and the direction of operation is reversed. For safety, a double setting system is used. When a change is cancelled after the confirmation message is displayed, the change is not made when moved to another setting item by Jog key. C o m m o n f u n c t i o n 47 Timer TIMER Function The timer is convenient during a competition to

on a full tank of fuel.

(Common)

Method Calling the setting screen Call the menu screen from the home screen by pressing the + key for 1 second. 1 second C o m m o n f u n c t i o n

"TIMER"

Select from the menu with the Jog key. Open the setting screen by pressing the Jog key. Select the item with the Jog key. Time set up Mode selection ON Switch selection Switch direction Reset Switch selection Switch direction TIMER Timer1 Timer2 When the throttle switch is selected at switch selection, hold the throttle stick in the position you want to set the ON/OFF point at ON direction setting and set the ON/OFF position by pressing the Jog key for 1 second. The timer is turned ON at points higher than this position. The ON direction can be switched by pressing the +

key or key. Timer TMR1TMR2 Mode selection Select timer mode from the "MODE"

with the orkey. or Timer time setting S e t t h e t i m e b y pressing the + key or key at each TIME

(minutes):(second) item. Range Default 0 99 minutes 59 seconds/10 minutes 00 second Range Default UP, DOWN, DN-STP/UP 48 Switch selection and ON direction setting Select the switch by pressing the + key or key at the ON-SW or RS-SW item and set the ON direction by pressing the + key or key at the ON direction setting item.

(Switch setting range/Default) ON-SW: SwA H, ST-THR, PWR-SW/SwA RS-SW: SwA H/SwA

(Switch ON direction/Default) 3P SW: NULL (normally o), UP, UP&DWN, UP&CNT, CENTER, 2P SW: NULL, UP, DOWN/NULL CNT&DN, DOWN/NULL Servo monitor Servo test

(Common) SERVO Function The servo display/servo test function displays the CH1 to CH10 servo output bar graph and tests servo operation.

Method

CAUTION Using the servo test will move the servos to their full throw. Do not use this with linkages installed. Using it may damage the servo and linkage. Calling the setting screen Call the menu screen from the home screen by pressing the + key for 1 second. 1 second

"SERVO"

Select from the menu with the Jog key. Open the setting screen by pressing the Jog key.

(Servo Monitor

12

Select the setting item with the Jog key.

(Servo Test Servo test ON/OFF

12

Channel Select

C o m m o n f u n c t i o n Switching to the servo test screen Switch the screen by selecting TEST and operating the jog key to the left and right. The servo operating position of each channel is displayed on a bar graph. Screen change Where "GRPH" is chosen, a Jog key is pressed in right or left. Type Select Cycle Select Speed setting Operation of a servo test Servo test Type/cycle/speed setting Select the setting item (TYPE, CYCL, SPD) with the Jog key and set the item by pressing the + key or key. or Range Default TYPELNR, JMP LNR CYCL1 100 10full speed at 1 SPD1 100 7full speed at 100 Channel selection Select the channel you want to test with the Jog key and select ACT/INH by pressing the + key or key. or Selection rangeACT, INH DefaultINHonly CH1 is ACT Servo test start/stop Select the "TEST" item with the Jog key and start/stop the servo test by pressing the + key or key. or Selection rangeON, OFF DefaultOFF 49 END POINT End point Function The End Point function adjusts the left and right servo throws, generates differential throws, and will correct improper linkage settings.

(Common) Servo throw At 100% setting the servo throw of each channel is about 40 for channels 1 to 4 and about 55 for channels 5 to 10. However, the maximum servo travel for channels 5 to 10 is about 110%.

*When channels 5 to 8 were mixed by aperon, dierential or ailvator, the throw becomes the same (about 40 ) as channels 1 to 4. Method Calling the setting screen Call the menu screen from the home screen by pressing the + key for 1 second. 1 second

"END POINT"

Select from the menu with the Jog key. Open the setting screen by pressing the Jog key. C o m m o n f u n c t i o n Select the channel with the Jog key. END POINT 1 2

1: AIL 2: ELE 3: THR 4: RUD 5: GER 100 /100 100 /100 100 /100 100 /100 100 /100 CH1 : AIL

100 100 The setting rate of each channel Left Down rate display Right Up rate display ChannelDisplay ACROBATIC HELICOPTER GLIDER (AF4) MULTICOPTER 1: AILAileron 6: FLPFlap1: AILAileron 6: PITPITCH1: AILAileron 6: FL2Flap2 1: AILAileron 6: AUX 2: ELEElevator7: AL2Aileron22: ELEElevator7: AUX 2: ELEElevator7: AUX 3: MOTMotor 8: FL3Flap3 3: THRThrottle8: AUX 3: THRThrottle8: AUX 4: RUDRudder9: FL4Flap4 4: RUDRudder9: AUX 4: RUDRudder9: AUX 5: GERGear 10: AUX 5: FLPFlap 10: AUX 10: AUX 2: ELEElevator7: AUX 3: THRThrottle8: AUX 4: RUDRudder9: AUX 5: GYRGYRO 10: AUX 5: MOD End point A channel is chosen by Jog key. Operate the stick or knob of the selected channel fully to the left (down) or right (up) and adjust the rate by pressing the + key or key. Selection range1 10ch or Range 0 140%

Default100%

When you want to return the set value to the initial value, press the + key and key simultaneously. Adjust the rate of each direction of the stick and VR by repeating step . 50 Trim reset Trim step

(Common) TRIM Function Trim Reset This function returns the trim of the model memory in use to the center (initial state). However, at this time, sub trim and trim step amount are not reset. Method Trim Step The amount of trim change per step can be changed between 1 and 40 according to the aircraft capacity and trim application. Set it to match the application. With ordinary aircraft, a setting of about 2 to 10 should be fine.

Calling the setting screen Call the menu screen from the home screen by pressing the + key for 1 second. 1 second

"TRIM"

Select from the menu with the Jog key. Open the setting screen by pressing the Jog key. Trim Reset TRIM The numbers in ( ) indicate the current trim position. (The trim operating range is 120 100[DT5,DT6]

Trim step Select the item with the Jog key. Trim reset Trim step rate Select the RESET item and press the Jog key for 1 second. 1 second For example, when the step size is the initial value (4), trim movement from center to end is 30 steps. If the step size is made 40, the trim moves 3 steps. A "beep" sounds to indicate that resetting is complete. At this time, the trim position number returns to 0. Trim step Select the trim you want to set from the STEP item and set the step size by pressing the + key or key. or Range1 40 Default4 When you want to return the set value to the initial value, press the + key and key simultaneously. C o m m o n f u n c t i o n 51 SUB TRIM Sub trim Function The Sub-Trim function is used to set the servo neutral position, and may be used to make fine adjustments to the control surface after linkages and pushrods are hooked up. When you begin to set up a model, be sure that the digital trims are set to their center position. Method

(Common) Setting precautions If sub trim is too large, the servo operating range may be exceeded at maximum control surface angle and generate a dead band in which the servo does not operate. First connect the linkage so that the amount of sub trim used is held to a minimum. Calling the setting screen Call the menu screen from the home screen by pressing the + key for 1 second. 1 second

"SUB TRIM"

Select from the menu with the Jog key. Open the setting screen by pressing the Jog key. C o m m o n f u n c t i o n Select the channel with the Jog key. SUB TRIM 1 2 CH1 : AIL 0

1: AIL 2: ELE 3: THR 4: RUD 5: GER 0 0 0 0 0 SUB trim rate of the selected channel. SUB trim rate of each channel. ChannelDisplay ACROBATIC HELICOPTER GLIDER (AF4) MULTICOPTER 1: AILAileron 6: FLPFlap1: AILAileron 6: PITPITCH1: AILAileron 6: FL2Flap2 1: AILAileron 6: AUX 2: ELEElevator7: AL2Aileron22: ELEElevator7: AUX 2: ELEElevator7: AUX 3: MOTMotor 8: FL3Flap3 3: THRThrottle8: AUX 3: THRThrottle8: AUX 4: RUDRudder9: FL4Flap4 4: RUDRudder9: AUX 4: RUDRudder9: AUX 5: GERGear 10: AUX 5: FLPFlap 10: AUX 10: AUX 2: ELEElevator7: AUX 3: THRThrottle8: AUX 4: RUDRudder9: AUX 5: GYRGYRO 10: AUX 5: MOD Sub trim A channel is chosen by Jog key. Selection range

(page 1) 1 5ch

(page 2) 6 10ch Select the SUB trim you want to set from channel item and set the rate by pressing the + key or key. or Range

-120 +120%

Default0%

When you want to return the set value to the initial value, press the + key and key simultaneously. 52 P.MIX1-6 Program mixing 16 Function Mixing that can independently customize 6 functions can be used. Programmable mixing is used to remove bad tendencies of the aircraft and

between arbitrary channels, this function includes

(Common) linking (linking with another mix), trim addition, offset, and switch setting functions. temporary combination. rate is set, slave servo operation is oset by that amount. P.MIX 1 4 (normal type) The following functions can be set for programmable mixing 1 to 4:

Mixing Channel Use this function by changing the channel because the master channel and slave channels initial setting is a When OFS was selected as the master channel, the mixing rate setting applies to slave only. When a mixing A knob (VR) or digital trim (DT5, DT6), as well as a channel, can be selected as the master channel. Trim selection Whether or not mixing includes master channel trim operation can be selected. Mixing reference point change The master channel mixing reference point can be shifted. Switch selection The programmable mixing ON/OFF switch can be selected. The switches that can be selected are switches A to H and the throttle stick. The switch operating direction can be set. When a 2 position switch was selected, up /down can be set, and when a 3 position switch was selected, up/up and down /up / and center/center/center and down /down can be selected. When the throttle stick was selected, the ON/OFF position and operation direction can be set. When "NULL" is selected, mixing is always ON. P. MIX 5 6curve type Programmable mix 5 to 6 allows setting of the mixing rate by 5 point curve. OFS and knob/digital trim use and trim selection by normal type master channel setting described above are impossible, but switch selection is possible. Method Calling the setting screen Call the menu screen from the home screen by pressing the + key for 1 second. 1 second

"P.MIX1-6"

Select from the menu with the Jog key. Open the setting screen by pressing the Jog key. C o m m o n f u n c t i o n 53 P.MIX Selection Calling the setting screen Use the Jog key to select the P.MIX Call the setting screen by pressing number you want to use. the Jog key. P.MIX1 4normal type P.MIX5 6curve type P.MIX 1-6 P.MIX1 4 set up screen Mixing rate adjustment Oset Master CH selection Slave CH selection Select the item with the Jog key. P.MIX1 4 Master CH Current position to P.MIX1 4 set up screen to P.MIX5 6 set up screen Function activation When INH is selected, the function cannot be used. When ON or OFF is selected, the function is activated. ON and OFF changes are linked to the switch. Trim ON/OFF Switch selection Switch direction or C o m m o n f u n c t i o n Function activation Select the MIX item and select ON or OFF by pressing the + key or key. Master/slave channel selection Select the MASTR channel you want to use by pressing the + key or key. Select the Slave channel you want to or When you do not want to use the function select INH. us by pressing the + key or key. A knob VR or digital trim DT5/DT6, as well as channels 1 to 10, can be specied as the master channel. In addition, when OFS was selected as the master channel, slave servo operation is oset. Mixing rate adjustment Select the RATE item and adjust the mixing rate by pressing the + key or key for each direction of the stick, etc. selected at the master channel. or Range-100 +100%

Default0%

When you want to return the set value to the initial value, press the + key and key simultaneously. Changing the ON/OFF Switch ON/OFF Switch selection Select the "SW" item and then select the switch by pressing the +

key or key. or Selection rangeSwA SwHTHR 54 or Switch ON direction setting Select the "POSI" item and select the switch ON direction by pressing the + key or key. 2P SWNULLalways ON, UP, DOWN 3P SWNULLalways ON, UP, UP&D, UP&C, CNTR, C&DN, DOWN THR stick: Hold the stick at the ON/OFF point and set the ON/OFF position by pressing the Jog key for 1 second. (If the Jog key is pressed for 1 second when the position was set, it returns to the NULL state.) The switch ON direction can also be selected by pressing the + key or key. 1 second Changing the mixing reference point Mixing reference point setting Select the "OFFST" item and hold the master side stick or knob in the position you want to set and set the new reference point by pressing the Jog key. Range-100 +100%

THR only 0 100%

Default0%

1 second Including trim operation Trim ON/OFF setting Select the "TRM" item and select ON or OFF by pressing the + key or key. RangeOFFON or DefaultOFF When you do not want to include trim in mixing select OFF. CAUTION At the end of setting, check that the mixing function is performed normally. Select the item with the Jog key. P.MIX5 6 set up screen 5Point curve setting Function activation Master CH select Slave CH select Switch selection Switch ON direction The set curve is displayed on a graph. When INH is selected, the function cannot be used. When ON or OFF is selected, the function is activated. ON and OFF changes are linked to the switch. P.MIX5 6 Refer to the P.MIX1 4 setting method described previously for settings other than the 5 point curve setting described below. 5point curve setting Select the setting item (P-1 P-5) of each point with the Jog key and set the amount of or movement of each point by pressing the + key or key. Range-100 +100%

Default0%

CAUTION At the end of setting, check that the mixing function is performed normally. C o m m o n f u n c t i o n 55 AUX-CHAN AUX Channel Function Auxiliary channel function (AUX-CH): defines the relationship between the transmitter controls and the receiver output for channels 5-10.

(Common) Remember that if you assign primary control of a channel to a switch which you later use for other functions (like dual/triple rates or airbrakes), every time you use that other function you will also be moving the auxiliary channel. Method Calling the setting screen Call the menu screen from the home screen by pressing the + key for 1 second. 1 second

"AUX-CHAN"

Select from the menu with the Jog key. Open the setting screen by pressing the Jog key. AUX-CHAN

SwG

HELICOPTER CH5 SwFSwitchF CH6 ----PITCH CH7 SwCSwitchC CH8 VRVolume CH9 SwA(SwitchA) CH10 SwD(SwitchD) AUX Channel Default ACROBATIC CH5 SwGSwitchG CH6 VRVolume CH7 DT5Trim5 CH8 DT6Trim6 CH9 SwA(SwitchA) CH10 SwD(SwitchD) GLIDER MULTICOPTER SwGSwitchG CH5 SwESwitchE CH5 CH6 SwCSwitchC CH6 VRVolume CH7 VRVolume CH7 DT5Trim5 CH8 DT6Trim6 CH8 DT6Trim6 CH9 SwA(SwitchA) CH9 SwA(SwitchA) CH10 SwD(SwitchD) CH10 SwD(SwitchD) AUX Channel A channel is chosen by Jog key. Select the "SW" item and then select the switch by pressing the + key or key. Selection range5 10ch or Selection rangeNULL, SwA SwH, VR, DT5, DT6 C o m m o n f u n c t i o n 56 WARNING The priority of AUX Don't assign two or more functions to one channel. Priority may be given to a higher rank function and a low rank function may be canceled. higher rank Priority low rank GYRO FLAPERON GYRO SW-G VR DT5 THR NEEDLE PITCH GYRO DT6 ACRO HELI GLIDER MULTICOPTER CH5 CH6 CH7 CH8 CH9 CH10 CH5 CH6 CH7 CH8 CH9 CH10 CH5 CH6 CH7 CH8 CH9 CH10 CH5 CH6 CH7 CH8 CH9 CH10 PITCH FLAP TRIM AIL DIFF AILVATOR SW-A SW-D GYRO PITCH GYRO ELE2 GOVERNOR SW-D FLAP1 FLAP2 AILERON2 FLAP3 FLAP4 CAMBR MIX GYRO SW-C GYRO GYRO SW-A SW-D GOVERNOR THR NEEDLE GYRO GYRO GYRO GYRO SW-F SW-C GOVERNOR SW-A VR DT5 SW-G SW-D DT6 SW-A VR SW-E VR DT6 C o m m o n f u n c t i o n 57 PARAMETER Parameter function Function PARAMETER submenu: sets those parameters you would likely set once, and then not disturb again.

(Common) Once you have selected the correct model you wish to work with, the next step is setting up the

Data reset RESET The present model data is reset. Data Reset does NOT reset, ATL Trim, TELEMETRY mode, or STK POSI Alarm. Model typeTYPE SWASH : Only helicopter WING : Only glider MODEL TYPE: sets the type of programming used for this model. The T10J has 30 model memories, which can each support:

One powered aircraft (ACRO) memory type (with multiple wing and tail congurations. See twin aileron servos, twin elevator servos, ELEVON, and V-TAIL for further information.) Eight helicopter swashplate types, including CCPM. See Helicopter MODEL TYPE for details. If you use CGY750, the swash type should choose H-1.( Swash type is chosen by setup in CGY750. Five glider wing types. See glider WING TYPE for details. Multicopter type. Before doing anything else to set up your aircraft, rst you must decide which MODEL TYPE best ts this particular aircraft. (Each model memory may be set to a dierent model type.) If your transmitter is a T10JA, the default is ACRO. If it is a T10JH, the default is HELI(H1). ATL TrimATL Adjustable travel limit (ATL): makes the channel 3 TRIM LEVER (THROTTLE TRIM) eective only at low throttle, disabling the trim at high throttle. This prevents pushrod jamming due to idling trim changes. This function defaults to ON. If you are not using channel 3 for throttle, you may want trim operation the same as on all other channels. To do so, set ATL to OFF. If you need the ATL to be eective at the top of the stick instead of the bottom, reverse the THR-REV setting. Note that this aects all models in the radio, not just the model you are currently editing. LCD contrastCONTRAST Contrast adjustment LCD screen. You adjust to legible contrast. set up range -10 +10 Back lightBACK-LIT Back light mode of a LCD screen can be chosen. ALWAYS / KEY-ON (Shines for a denite period of time after key operation.) / OFF Light timeLIT-TIME Sets the length of time the backlight will stay on. Set up range 1 30 Light adjustmentLIT-ADJS Light volume adjustment of a back light. Set up range 1 30 Home display HOME-DSP Item selection displayed on a home screen Futaba logo (Default), USR-NAME , RX BATT, DT5/DT6, THR/PIT (Case of helicopter, the position of a throttle and pitch.) C o m m o n f u n c t i o n 58 Battery alarmBATT-ALM Select the battery alarm voltage according to the battery to be used. 4 dry cell batteries 4.2V DRY4 HT5F1800B (NiMH battery) 5.0V NiMH5 FT2F2100B (Lithium ferrite battery) 5.8V LiFe2 Battery alarm vibrationBATT VIB Battery alarm is told with vibration. Buzzer tone BUZ-TONE The tone of buzzer sound when a key is pressed. Set up range : OFF,1(low) 100(high) Jog key navigation Jog-NAVI Blink at the time of Jog key operation, Display of the operation direction. Jog lightJog-LIT ON/OFF of a Jog key light. Jog light timeJog-TIME Time setting in which a Jog key light shines. Set up range : 1 30(s) Telemetry mode settingTELEMETRY MODE Sets whether or not telemetry is activated. When using 2 receivers with 1 transmitter, select INH. RangeACT / INH Telemetry display units settingTELEMETRY UNIT Sets whether the telemetry display is in meters or yards/pounds. RangeMETER / YARD /

Speech language settingSPEECH LANGUAGE Sets the speech language when listening to telemetry information through earphones. RangeJapanese (JPN), English (English), German (Deutsch) Speech volume settingSPEECH VOLUME Sets the volume when listening to telemetry information through earphones. RangeLOW / HIGH Stick position alarm settingSTK POSI ALRM Can be set so that an audible alarm sounds once when the throttle stick reaches the set position. C o m m o n f u n c t i o n 59 Method Calling the setting screen Call the menu screen from the home screen by pressing the + key for 1 second. 1 second

"PARAMETER"

Select from the menu with the Jog key. Open the setting screen by pressing the Jog key. PARAMETER 1 2 3 4 5 Data reset Model type Swash type Wing type ATLTrim

Execute

(In the case of a helicopter )

(In the case of a glider )

Next page 2 5 LCD contrastCONTRAST Back lightBACK-LIT Light timeLIT-TIME Light adjustmentLIT-ADJS Home display HOME-DSP Battery alarmBATT ALM Buzzer tone BUZ-TONE Battery alarm vibrationBATT VIB Jog key navigation JOG-NAVI Jog light timeJOG-TIME Jog lightJOG-LIT TELEMETRY MODE TELEMETRY UNIT SPEECH LANGUAGE SPEECH VOLUME Stick position alarmSTK POSI ALRM page 1 page 2 page 3 page 4 page 5 Date reset the Jog key for 1 second. Call the "RESET" from the PARAMETER by Press Date reset by pressing the Jog key. 1 second Conrmation message "sure?" blinks. A confirmation "beep" sounds and

"COMPLETE" is displayed on the screen is complete. For safety, a double setting system is used. You need to conrm your setting changes by pressing the jog key. When "COMPLETE" can be seen, it is the completion of reset. CAUTION Only the throttle channel (CH3) initial setting is REV (reverse). Thoroughly check the Hi and Low directions of the engine or motor used and be careful that they do not suddenly run at full speed.Even after data reset, CH3 is reversed. C o m m o n f u n c t i o n 60 Model type Select the "TYPE" item and then select the model type by pressing the + key or key. or The new model type is displayed on the screen. Press the Jog key for 1 second. 1 second Model type change by pressing the Jog key. Confirmation message

"sure?" blinks. A confirmation "beep"

sounds is complete. For safety, a double setting system is used. You need to conrm your setting changes by pressing the jog key. If you fail to press the jog key and see "COMPLETE" on your screen, your changed are not saved. Selection range ACROBATIC, HELICOPTER,GLIDER,MULTI COPT Swash typefor Heli Select the "SWASH" item and then select the swash type by pressing the + key or key. Press the Jog key for 1 second. 1 second Swash type change by pressing the Jog key. or Confirmation message

"sure?" blinks. A confirmation "beep"

sounds is complete. For safety, a double setting system is used. You need to conrm your setting changes by pressing the jog key. If you fail to press the jog key and see "COMPLETE" on your screen, your changed are not saved. Selection rangeH-1, HR3, H-3, HE3, HN3, H-2, H-4, H4X Wing typefor Glider Select the "WING" item and then select the swash type by pressing the + key or key. Press the Jog key for 1 second. 1 second Swash type change by pressing the Jog key. or Confirmation message

"sure?" blinks. A confirmation "beep"

sounds is complete. For safety, a double setting system is used. When a change is cancelled after the conrmation message is displayed, the change is not made when moved to another setting item by Jog key. Selection range1AIL, 2AIL, 2A+1F, 2A+2F, 2A+4F ATL Trim ON/OFF Select the "ATL" item and change the mode by pressing the + key or key. or Selection rangeON, OFF DefaultOFF C o m m o n f u n c t i o n 61 LCD contrast Select the "CONTRAST" item and change numerical value (contrast) by pressing the + key or key. or Selection range-10

+10 Default0 Back-light Light-time Light-adjustment Back-light mode Select the "BACK-LIT" item and change the mode by pressing the

+ key or key. Light-time Select the "LIT-TIME" item and change numerical value (time) by pressing the + key or key. or or It is only a case in "KEY-ON"

mode here. Light-adjustment Select the "LIT-ADJ" item and change numerical value

(brightness) by pressing the + key or key. or It is the brightest at 30. Selection range1 30(s) Default10(s) Selection range1 30 Default15 When you want to return the set value to the initial value, press the

+ key and key simultaneously. When you want to return the set value to the initial value, press the

+ key and key simultaneously.

"ALWAYS"always ON

"OFF"always OFF

"KEY-ON"It light on after Key operation. Selection range ALWAYS, OFF, KEY-ON DefaultALWAYS Home display by pressing the + key or key. C o m m o n f u n c t i o n Select the "HOME-DSP" item and change the mode

"Futaba"Display about a Futaba logo.

"USR-NAME"Display about a user name.

"DT5/DT6"Display about the position of DT5 and DT6

"RX BATT"Display about the receiver battery voltage

"THR/PIT"Display about the position of pitch and throttle. Battery alarm voltage Select the "BATT ALM" item and change the numerical value (voltage) by pressing the + key or key. or AA alkaline batterys 4.2V DRY4 Futaba HT5F1800B 5.0V NiMH5 Futaba FT2F2100B 5.8V LiFe2 62 Selection range Futaba, USR-NAME,DT5/

DT6, RX BATT, THR/PIT(*) DefaultFutaba

*Only Heli mode can be chosen about THR/PIT. Selection range 6.2V 6.6V 7.0V 7.4V 4.2V 4.6V 5.0V 5.4V 5.8V

*The voltage drop of a rechargeable battery and a dry cell battery is different. When using a rechargeable battery, always change the voltage. Battery alarm voltage vibration Select the "BATT VIB" item and change the ON or OFF by pressing the + key or key. or Selection range ON, OFF ON The battery alarm of a transmitter is told with vibration. Buzzer tone Select the "BUZ-TONE" item and change the numerical value (tone) by pressing the + key or key. The higher the numerical value the higher the tone. or Jog key navigation Select the "Jog-NAVI" item and change the mode by pressing the + key or key. or When NAVI selected ashes when the Jog key was pressed. When a function that only operates in the vertical direction is selected, the LED blinks vertically. Jog light Select the "Jog-LIT" item and change the mode by pressing the + key or key. or

"ALWAYS"The light is always switched on.

"KEY-ON"KEY operation Light on.

"OFF"Always o. Selection range OFF, 1 100 When you want to return the set value to the initial value, press the + key and key simultaneously. Selection range ON,OFF When a function t h a t o p e r a t e s i n t h e v e r t i c a l a n d horizontal directions is selected, the LED blinks vertically and horizontally. Selection range ALWAYS, KEY-ON, OFF DefaultKEY-ON C o m m o n f u n c t i o n 63 Jog light time Select the "Jog-TIME" item and change numerical value (time) by pressing the + key or key. or Selection range 1 30 Default10 Jog-Lit sets the lighting time when KEY-ON was set. When you want to return the set value to the initial value, press the + key and key simultaneously. Telemetry mode Select the "TELEMETRY-MODE" item and change the mode by pressing the + key or key. or Telemetry unit Select the "TELEMETRY-UNIT" item and change the mode by pressing the + key or key. or Speech language Select the "SPEECH-LANGUAGE" item and change the language by pressing the + key or key. or Speech volume Select the "SPEECH-VOLUME" item and change the volume by pressing the + key or key. or C o m m o n f u n c t i o n 64 Selection range ACT, INH Selection range METER, YARD Selection range Japanese, English, Deutsch Selection range HIGH, LOW Stick position alarm An alarm (single beep) can be sounded at the specied throttle stick position. Alarm function ON/OFF can be set by switch. Select "Parameter"

Press the Jog key to the side and select page 5. When the THR stick is set to the specied position. Select the item with the Jog key. STK POSI ALRM

5 INH ON/OFF Switch selsction Switch direction Stick position

Beep sounds Parameter

STK POSI ALRM,Telemetry m o d e A T L trim (MDL)

When INH is selected, the function cannot be used. When ON or OFF is selected, the function is activated. ON and OFF changes are linked to the switch. The number in parenthesis is the current throttle stick position. Stick position is chosen by Jog key. Set the throttle stick to the position at which you want to generate the alarm. When the Jog key is held down the alarm sounds at that position.

5

Memorize the position at which the beep is to sound. THR Stick C o m m o n f u n c t i o n 65 C o m m o n f u n c t i o n TELEMETRY Telemetry Function This screen displays and sets the various information from the receiver. An alarm and vibration can be generated depending on the information. For example, a drop in the voltage of the receiver battery housed in the aircraft can be reported by an alarm.

(Common) This function can only be used in the T-FHSS Air mode. The S-FHSS system cannot use telemetry. Telemetry sensors sold separately can be mounted in the aircraft to display a variety of information. (Receiver voltage does not require a sensor.) The telemetry function cannot be used if the telemetry mode of the parameters is not ACT. When 2 receivers are used with 1 transmitter, the telemetry function cannot be used. Viewing the receiver voltage. Setting is unnecessary. When menu telemetry is listened to, the voltage appears. P.66 Viewing the drive battery voltage. Using various optional telemetry sensors. Using several telemetry sensors of the same type. Setting alarms from the telemetry information. CA-RVIN-700 and wiring work are necessary. P.70 Optional telemetry sensors are necessary. T10J setting is unnecessary. P.74 82 Setting by "sensor" in the menu is necessary.

(Slot setting is necessary.) P.84 Setting by "Telemetry" in the menu is necessary. P.75 82 RX-BATT Viewing the receiver voltage. In the initial state, the receiver voltage is displayed at the transmitter. Display Calling the setting screen Call the menu screen from the home screen by pressing the + key for 1 second. 1 second

"TELEMETRY"

Select from the menu with the Jog key. Open the setting screen by pressing the Jog key. Receiver voltage display TELEMETRY RX-BATT

RECEIVER EXT-VOLT

RECEIVER 66 How to display receiver voltage on a home screen. PARAMETER HOME-DSP

"RX BATT" is chosen by key or key. Viewing the receiver voltage maximum and minimum values. In the initial state, the receiver voltage maximum and minimum values are displayed in the transmitter. (Value until reset) Display Calling the setting screen Select "RX-BATT" from the telemetry screen with the Jog key. Open the setting screen by pressing the Jog key. Receiver voltage MIN Receiver voltage display Receiver voltage MAX RX-BATT MIN/MAX=

(ALARM) (VIB) (LIMIT)

MIN/MAX reset Select "MIN/MAX" from the RX-BATT screen with the Jog key. Date reset by pressing the Jog key for 1 second. A confirmation "beep"

sounds when complete.

WARNING

C o m m o n f u n c t i o n 67 Setting receiver voltage alarm. Use this setting to sound an alarm when the receiver battery voltage drops dangerously low. VIB

(vibration) that vibrates the transmitter at the same time can also be set. Method Calling the setting screen Select "RX-BATT" from the telemetry screen with the Jog key. Open the setting screen by pressing the Jog key. DN (down) shows than an alarm is generated when the voltage drops below the set voltage. RX-BATT MIN/MAX=

(ALARM) (VIB) (LIMIT)

Alarm set In the RX-BATT screen state, select

(ALARM) from the menu with the Jog key. Select the "ACT" by pressing the + key or key. or C o m m o n f u n c t i o n Vibration set In the RX-BATT screen state, select

(VIB) from the menu with the Jog key. Select the "TYP1 TYP3" by pressing the + key or key. or

"VIB" types TYP 1 TYP 2 TYP 3 Alarm voltage set In the RX-BATT screen state, select

(LIMIT) 0.0V from the menu with the Jog key. Select the voltage by pressing the + key or key. or Selection range 3.5V 8.4V When you want to set 5.0V, press the

+ key and key simultaneously. 68 Listening to the receiver voltage by speech. The receiver voltage can be heard verbally from the transmitter with a commercial earphone (3.5 plug). The speech function can be turned on and o with the specied switch. Method Calling the setting screen Select "RX-BATT" from the telemetry screen with the Jog key. Open the setting screen by pressing the Jog key. RX-BATT MIN/MAX=

(ALARM) (VIB) (LIMIT)

Speech ACT / INH Selects the switch that turns the speech function on and o. Speech In the RX-BATT screen state, select

(SPEECH) from the menu with the Jog key. Select the "ACT" by pressing the + key or key. or Switch In the RX-BATT screen state, select

(SW) from the menu with the Jog key. In "NULL", a speech always turns on. Select the switch by pressing the + key or key. or Selection range NULL, SWA SWH OFF ON OFF OFF ON 2 Position 3 Position C o m m o n f u n c t i o n 69 EXT-VOLT When connected as shown in the gure, the voltage of the drive battery in the aircraft and another power supply battery can be displayed at the T10J. CA-RVIN-700 (external voltage input connector sold separately) is necessary. Soldered wiring work is necessary. Extra Voltage Port R3008SB Black line CA-RVIN-700 Red line with external power input must be less than 70V Power Battery or another power supply for servos Fuse Branch To Motor Controller or Servo C o m m o n f u n c t i o n EXT-Voltage display When connected as shown in the gure, the drive battery voltage is displayed at the transmitter. Display Calling the setting screen Call the menu screen from the home screen by pressing the + key for 1 second. 1 second

"TELEMETRY"

Select from the menu with the Jog key. Open the setting screen by pressing the Jog key. EXT-Voltage display TELEMETRY RX-BATT

RECEIVER EXT-VOLT

RECEIVER 70 EXT-Voltage MIN/MAX In the initial state, the EXT-voltage maximum and minimum values are displayed at the transmitter.

(Value until reset) Calling the setting screen Select "EXT-VOLT" from the telemetry screen with the Jog key. Open the setting screen by pressing the Jog key. EXT-Voltage MIN EXT-Voltage display EXT-Voltage MAX EXT-VOLT MIN/MAX=

(ALARM) (VIB) (LIMIT)

MIN/MAX reset In the EXT-VOLT screen state, select

(MIN/MAX) from the menu with the Jog key. Date reset by pressing the Jog key for 1 second. A confirmation "beep"

sounds is complete. C o m m o n f u n c t i o n 71 EXT-Voltage alarm set up This setting will sound an alarm when the EXT-voltage drops dangerously low. VIB (vibration) that vibrates the transmitter at the same time can also be set. Method Calling the setting screen Select "EXT-VOLT" from the telemetry screen with the Jog key. Open the setting screen by pressing the Jog key. DN (down) shows than an alarm is generated when the voltage drops below the set voltage. EXT-VOLT MIN/MAX=

(ALARM) (VIB) (LIMIT)

Alarm set In the EXT-VOLT screen state, select

(ALARM) from the menu with the Jog key. Select the "ACT" by pressing the + key or key. or C o m m o n f u n c t i o n Vibration set In the EXT-VOLT screen state, select

(VIB) from the menu with the Jog key. Alarm voltage set In the EXT-VOLT screen state, select

(LIMIT) from the menu with the Jog key. Select the "TYP1 TYP3" by pressing the + key or key.

"VIB" types If the following types are selected, the transmitter will vibrate during the warning. or TYPE 1 TYPE 2 TYPE 3 Select the voltage by pressing the + key or key. or Selection range 0.0V 70.0V When you want to set 5.0V, press the

+ key and key simultaneously. 72 Listening to the EXT-voltage by speech. The EXT- voltage can be heard verbally from the transmitter with a commercial earphone (3.5mm plug). The speech function can be turned on and o with the specied switch. Method Calling the setting screen Select "EXT-VOLT" from the telemetry screen with the Jog key. Open the setting screen by pressing the Jog key. EXT-VOLT MIN/MAX=

(ALARM) (VIB) (LIMIT)

Speech ACT / INH Speech ON/OFF Switch selection Speech In the EXT-VOLT screen state, select

(SPEECH) from the menu with the Jog key. Select the "ACT" by pressing the + key or key. or Switch set In the EXT-VOLT screen state, select

(SW) from the menu with the Jog key. In "NULL", a speech always turns on. Select the switch by pressing the + key or key. or Selection range NULL, SWA SWH OFF ON OFF OFF ON 2 Position 3 Position C o m m o n f u n c t i o n 73 Various telemetry sensors (optional) information display and alarm setting Various telemetry sensors (sold separately) are connectable to the S.BUS2 port of the R3008SB through a 3-way hub and relay terminals. The information of sensors connected at initialization can be viewed as long as 2 or more of the same kind of sensor are not used (for example, 2 temperature sensors). Sensors that can be used with the T10J: Futaba SBS-01T, SBS-01RM, SBS-01RO, SBS-01A, SBS-01V, SBS-01G Robbe sensors that can be used with the T10J: Robbe TEMP125, GPS-1675, VARIO-1712, VARIO-1672, CURR-1678

*Futaba does not sell Robbe sensor. Sensor Connection TEMP Sensor SBS-01T

SBS-01RM

SBS-01RO S.BUS2 Connector HUB HUB Altitude Sensor SBS-01A Voltage Sensor SBS-01V GPS Sensor SBS-01G HUB

*Refer to the manual of each sensor for the mounting instruction to the model of sensor. Method Sensor information can be viewed by calling telemetry from the menu and calling the connected sensor display page. The detailed setting screen of that sensor can be called by selecting and pressing the sensor you want to select with the Jog key. Refer to the receiver battery (RX-BATT) item for a description of key operation. Select "TELEMETRY" from the menu with the Jog key. The sensor item of your choice is chosen by Jog key, and Jog key is pressed. TELEMETRY 1 2 3 RX-BATT

RECEIVER 02 TEMP

SBS-01T EXT-VOLT

RECEIVER 05 R.P.M 0rpm SBS-01RM/O TELEMETRY 1 2 3 RX-BATT

RECEIVER 02 TEMP

SBS-01T EXT-VOLT

RECEIVER 05 R.P.M 0rpm SBS-01RM/O Sensor set up C o m m o n f u n c t i o n 74 TEMP : Display of SBS-01T(Option), and alarm setup

*A temperature sensor must be installed in the aircraft. TEMP is a screen which displays/sets up the temperature information from an optional temperature sensor. The temperature of the model (engine, motor,

alarm and/or vibration will alert you. Conversion of a display unit is performed by "TELEMETRY UNIT" of "PARAMETER".

TEMP

(ALARM) (VIB) (LIMIT)

date reset by pressing the Jog key for 1 second.

"VIB" type If the following types are selected, the transmitter will vibrate during the warning. TYPE 1 TYPE 2 TYPE 3

OFF ON OFF OFF ON 2 Position 3 Position Alert set : Hot warning

*When the + - key simultaneous press, the rate is reset to the initial value.

*When the + - key simultaneous press, the rate is reset to the initial value.

C o m m o n f u n c t i o n 75 R.P.M : Display of SBS-01RM/RO(Option), and alarm setup

*A RPM sensor must be installed in the aircraft. RPM is a screen which displays / sets up the RPM information from an optional RPM sensor. The RPM of the model (engine, motor, etc.)

alarm and/or vibration will alert you.

R.P.M MAX=

(ALARM) (VIB) (LIMIT)

date reset by pressing the Jog key for 1 second.

"VIB" type If the following types are selected, the transmitter will vibrate during the warning. TYPE 1 TYPE 2 TYPE 3 C o m m o n f u n c t i o n

OFF ON OFF OFF ON 2 Position 3 Position

*When the + - key simultaneous press, the rate is reset to the initial value.

Alert set : Under rotations

*When the + - key simultaneous press, the rate is reset to the initial value.

76 ALTITUDE : Display of SBS-01A / SBS-01G(Option), and alarm setup

the altitude information from an optional altitude sensor or GPS sensor. The altitude of the model

(low) than preset altitude, you can be told by alarm. To show warning by vibration can also be chosen. Data when a power supply is turned on shall be 0 m, and it displays the altitude which changed from there. Even if the altitude of an airfield is high,

*An altitude sensor or GPS sensor must be installed in the aircraft. that shall be 0 m and the altitude difference from

altitude from atmospheric pressure. Atmospheric pressure will get lower as you go up in altitude, using this the sensor will estimate the altitude. Please understand that an exact advanced display cannot be performed if atmospheric pressure changes in a weather situation. Conversion of a display unit is performed by "TELEMETRY UNIT" of "PARAMETER".

ALTITUDE

(ALARM) (VIB) (LIMIT)

Jog key

"VIB" type If the following types are selected, the transmitter will vibrate during the warning. TYPE 1 TYPE 2 TYPE 3

OFF ON OFF OFF ON 2 Position 3 Position Alert set : Low side

*When the + - key simultaneous press, the rate is reset to the initial value.

*Atmospheric pressure is changed according to the weather also

Alert set : High side

*When the + - key simultaneous press, the rate is reset to the initial value.

C o m m o n f u n c t i o n 77 VARIO : Display of SBS-01A / SBS-01G(Option), and alarm setup

*An altitude sensor or GPS sensor must be installed in the aircraft. Conversion of a display unit is performed by "TELEMETRY UNIT" of "PARAMETER".

variometer information from an optional altitude sensor or GPS sensor.

be known.

alarm and/or vibration will alert you.

VARIO

(ALARM) (VIB) (LIMIT)

OFF ON OFF OFF ON 2 Position 3 Position C o m m o n f u n c t i o n

date reset by pressing the Jog key for 1 second.

"VIB" type If the following types are selected, the transmitter will vibrate during the warning. TYPE 1 TYPE 2 TYPE 3 Alert set : Rise side

*When the + - key simultaneous press, the rate is reset to the initial value.

Alert set : Low side

*When the + - key simultaneous press, the rate is reset to the initial value.

78 DISTANCE : Display of SBS-01G(Option), and alarm setup

*An GPS sensor must be installed in the aircraft. The Distance screen displays and sets altitude data from an SBS-01G GPS Sensor (sold separately), and allows the distance to the airborne aircraft to be read by the transmitter. When the aircraft flies inside or outside the set distance an alarm and vibration alerts the pilot. Conversion of a display unit is performed by "TELEMETRY UNIT" of "PARAMETER".

*Positioning time of GPS A short time is required until the positioning of the GPS is established. In the meantime, don't move the model during this process. Wait until the GPS sensor's LED turns solid green. If it is blinking green it is still acquiring the satellites signals.

DISTANCE 1 2 G

(ALARM) (VIB) (LIMIT)

Jog key

"VIB" type If the following types are selected, the transmitter will vibrate during the warning. TYPE 1 TYPE 2 TYPE 3

OFF ON OFF OFF ON 2 Position 3 Position

*When the + - key simultaneous press, the rate is reset to the initial value.

*Now, the position of the present model was set to 0 m. Setting a "too far" alert distance

*When the + - key simultaneous press, the rate is reset to the initial value.

C o m m o n f u n c t i o n 79 2nd page of [DISTANCE]

DISTANCE 1 2 G

POSITION

E=

L S N T A Altitude SURFACE

C o m m o n f u n c t i o n 80 SPEED : Display of SBS-01G(Option), and alarm setup The speed screen displays and sets the speed data from an SBS-01G (GPS sensor) sold separately. The speed of the aircraft during flight can be displayed.

*An GPS sensor must be installed in the aircraft. and with a tail wind, the displayed speed increases. Conversion of a display unit is performed by "TELEMETRY UNIT" of "PARAMETER". After flight, the maximum speed during flight can be viewed. Because this speed is based on position data from a GPS satellite, the ground speed is displayed instead of air speed. Consequently, with a head wind, the displayed speed decreases

*Positioning time of GPS A short time is required until the positioning of the GPS is established. In the meantime, don't move the model during this process. Wait until the GPS sensor's LED turns solid green. If it is blinking green it is still acquiring the satellites signals.

SPEED

MAX=

(ALARM) (VIB) (LIMIT)

Jog key

"VIB" type If the following types are selected, the transmitter will vibrate during the warning. TYPE 1 TYPE 2 TYPE 3

OFF ON OFF OFF ON 2 Position 3 Position

*When the + - key simultaneous press, the rate is reset to the initial value.

*When the + - key simultaneous press, the rate is reset to the initial value.

*Speed alarm precaution Since the GPS speed sensor displays the ground speed, it cannot be used as a stall alarm. For example, an aircraft that stalls at 50km/h will stall if the tailwind is 5km/h or greater even through 55km/h is displayed by ground speed. In addition, with an aircraft that will disintegrate in midight at 400km/h at an over-speed alarm, when the headwind reaches 30km/h the airplane will disintegrate in midair due to over speeding even at a ground speed of 370km/h. C o m m o n f u n c t i o n 81 BATTERY / EXT-VOLT: Display of SBS-01V(Option), and alarm setup

connect of R3008SB SBS-01V Battery

*SBS-01V must be installed in the aircraft. SBS-01V measures two batteries. The drive battery connected to two lines is displayed on EXT-

VOLT. The battery for receivers connected to 3P lines is displayed here.

BATTERY MIN/MAX=

(ALARM) (VIB) (LIMIT)

date reset by pressing the Jog key for 1 second.

"VIB" type If the following types are selected, the transmitter will vibrate during the warning. TYPE 1 TYPE 2 TYPE 3 C o m m o n f u n c t i o n

OFF ON OFF OFF ON 2 Position 3 Position

EXT-VOLT

MIN/MAX=

(ALARM) (VIB) (LIMIT)

date reset by pressing the Jog key for 1 second.

"VIB" type If the following types are selected, the transmitter will vibrate during the warning. TYPE 1 TYPE 2 TYPE 3

OFF ON OFF OFF ON 2 Position 3 Position

*When the + - key simultaneous press, the rate is reset to the

initial value.

82 SENSOR Sensor Slot Function This screen registers the telemetry sensors used with the transmitter. When only one of a certain type of sensor is used, this setting is unnecessary and the sensor can be used by simply connecting it

(Common) to the S.BUS2 port of the transmitter. When using 2 or more of the same kind of sensor, they must be registered here.

[What is a slot?]

from to .

sensors"slot". There are slots

and other data sensor units may use . Using a sensor which uses two or more slots, the required number of slots is automatically assigned by setting up a start slot. unused slots and memorize that slot. When 2 or more of the same kind of sensor are used, the sensors themselves must allocate The "SENSOR" of a menu is chosen, and Jog key press. Jog key presses side and makes it 2 pages. SENSOR SLOT 1 2 3 4 5 6 SENSOR SLOT 1 2 3 4 5 6

Slot number 7 SBS-01V

9 SBS-01G 10 SBS-01G 11 SBS-01G 12 SBS-01G 8 slots SBS-01G is used. 3 slots SBS-01A is used. SensorIDWhen multiple sensors of the same type are not used, ID is unnecessary. Assignable slot *Altimeter, GPS, and other sensors that display a large amount of data require multiple slots.

*Depending on the type of sensor, the slot numbers that can be allocated may be limited. Sensor TEMP(SBS-01T) RPM(SBS01RM,SBS-

01RO) Voltage(SBS-01V) Altitude(SBS-01A) GPS(SBS-01G) TEMP125-F1713 VARIO-F1712 VARIO-F1672 CURR-F1678 GPS-F1675 The required number of slots 1 slot 1 slot 2 slot 3 slot 8 slot 1 slot 2 slot 2 slot 3 slot 8 slot The number which can be used as a start slot Selling area 1 31 1 31 1 , 2 , 3 , 4 , 5 , 6 , 8 , 9 , 1 0 , 1 1 , 1 2 , 1 3 , 1 4 , 1 6 , 1 7 , 1 8 , 1 9 , 2 0 1 , 2 , 3 , 4 , 5 , 8 , 9 , 1 0 , 1 1 , 1 2 , 1 3 , 1 6 , 1 7 , 1 8 , 1 9 , 2 0 , 2 1 , 2 4

, 2 1 , 2 2 , 2 4 , 2 5 , 2 6 , 2 7 , 2 8 , 2 9 , 3 0

, 2 5 , 2 6 , 2 7 , 2 8 , 2 9 8 , 1 6 , 2 4 1 31 1 , 2 , 3 , 4 , 5 , 6 , 8 , 9 , 1 0 , 1 1 , 1 2 , 1 3 , 1 4 , 1 6 , 1 7 , 1 8 , 1 9 , 2 0 1 , 2 , 3 , 4 , 5 , 6 , 8 , 9 , 1 0 , 1 1 , 1 2 , 1 3 , 1 4 , 1 6 , 1 7 , 1 8 , 1 9 , 2 0 1 , 2 , 3 , 4 , 5 , 8 , 9 , 1 0 , 1 1 , 1 2 , 1 3 , 1 6 , 1 7 , 1 8 , 1 9 , 2 0 , 2 1 , 2 4

, 2 1 , 2 2 , 2 4 , 2 5 , 2 6 , 2 7 , 2 8 , 2 9 , 3 0

, 2 1 , 2 2 , 2 4 , 2 5 , 2 6 , 2 7 , 2 8 , 2 9 , 3 0

, 2 5 , 2 6 , 2 7 , 2 8 , 2 9 8 , 1 6 , 2 4 Global Europe C o m m o n f u n c t i o n 83 REGISTERWhen using multiple telemetry sensors of the same type.

Sensor connect Receiver battery Hub Sensor Connect a sensor to add T10J Method Select from the menu with the Jog

"SENSOR"

Open the setting screen by pressing the Jog key. key. Calling the setting screen Call the menu screen from the home screen by pressing the + key for 1 second. 1 second C o m m o n f u n c t i o n SENSOR SLOT 1 2 3 4 5 6 Jog key presses side and makes it 6pages. SENSOR SLOT 1 2 3 4 5 6

Left 1-time press or Right 10-

time press 31 INHBIT

Sensor register

"REGISTER" in SENSOR SLOT page 6 is chosen by Jog key. Press the Jog key for 1 second. Press the Jog key. Conrmation message

"sure?" blinks. A confirmation "beep"

sounds when complete.

"COMU-ERROR" : When the number of slots needed in registration is insufficient, an error is displayed and registration cannot be performed. 84 SENS SLOT This procedure changes the slot number of one registered sensor. Sensor connection T10J Calling the setting screen

"SENS SLOT" in SENSOR SLOT page 6 is chosen by Jog key. Jog key press. Receiver battery Hub Sensor Connect a sensor to add READ is chosen and Jog key is pressed "sure?"

Jog key is pressed. SENSOR SLOT SETTING READ

"COMU-ERROR" when reading goes wrong. Once the sensor is read correctly, the Sensor ID will be displayed Number is chosen, Input a number by the key or key.

*Referred to Assignable slot C o m m o n f u n c t i o n 85 INITIALIZE This function returns the slot setting and alarm setting of each sensor to their initial value (shipped state). Various sensors can be used one by one.

*The slot number memorized at each sensor cannot be initialized. Calling the setting screen Call the menu screen from the home screen by pressing the + key for 1 second. 1 second Select from the menu with the Jog

"SENSOR"

key. Open the setting screen by pressing the Jog key. Jog key presses side and makes it 6 pages SENSOR SLOT 1 2 3 4 5 6 SENSOR SLOT 1 2 3 4 5 6

Left 1-time press or Right 10-

time press 31 INHBIT

Initialize

"INITIALIZE" in SENSOR SLOT page 6 is chosen by Jog key. Press the Jog key for 1 second. Press the Jog key. Conrmation message

"sure?" blinks. The initialization is done when "COMPLETE" is shown. C o m m o n f u n c t i o n 86

ALL CLEAR alarm settings of each sensor are also cleared.

*The slot number memorized at each sensor is not initialized. Calling the setting screen Call the menu screen from the home screen by pressing the + key for 1 second. 1 second Select

"SENSOR"

from the menu with the Jog key. Open the setting screen by pressing the Jog key. Jog key presses side and makes it 6 pages SENSOR SLOT 1 2 3 4 5 6 SENSOR SLOT 1 2 3 4 5 6

Left 1-time press or Right 10-

time press 31 INHBIT

All clear

"ALL CLEAR" in SENSOR SLOT page 6 is chosen by Jog key. Press the Jog key for 1 second. Press the Jog key. Conrmation message

"sure?" blinks. The clearing is done when "COMPLETE" is shown. C o m m o n f u n c t i o n 87 Manually assigning a sensor slot number

required to store a start slot number in a sensor. Calling the setting screen Call the menu screen from the home screen by pressing the + key for 1 second. 1 second

"SENSOR"

Select from the menu with the Jog key. Open the setting screen by pressing the Jog key. Jog key is pressed in a side and it searches for an empty slot. (INHIBIT). SENSOR SLOT 1 2 3 4 5 6 SENSOR SLOT 1 2 3 4 5 6

13 SBS-01G 14 SBS-01G 15 SBS-01G 16 INHIBIT 17 INHIBIT 18 INHIBIT Assignment of slot When an INHIBIT slot is selected and the Jog key is pressed, a list of sensors that can be assigned to that slot is displayed. Select the sensor you want to assign and press the Jog key. Press the END key. END

*Refer to the <Assignable slots>

table. C o m m o n f u n c t i o n 88 SBUS LINK S.BUS servo link Function An S.BUS servo can memorize the channel and various settings you input. Servo setting can be performed on the T10J screen by wiring the servo

(Common)

* With some S.BUS(2) servos, there are some functions with

screen will change. (Only the function which can be used by a servo is displayed.)

if a stick is moved, the test of operation of the servo can be operated and carried out. Method Calling the setting screen Call the menu screen from the home screen by pressing the + key for 1 second. 1 second

"SBUS LINK"

Select from the menu with the Jog key. Open the setting screen by pressing the Jog key. S.BUS SX MODE IN Press the Jog key for 1 second. S.BUS SX6

(NO LINK) READ PLEASE DO NOT YET CONNECT A SERVO Connect a S.BUS servo to set up. T10J S.BUS Servo setting

"READ" is chosen by Jog key, Press the Jog key for 1 second. 1 second Receiver battery HUB S.BUS/

S.BUS2 Servo READ is completed and the item in which data of S.BUS servo and a setup are possible is displayed.

* "COMU-ERROR" :

It is failure of READ. Check a servo and connection. CAUTION

S.BUS servo is set up.

"WRITE" is chosen and Jog key is pressed for 1 second. T h e w r i t i n g i s d o n e w h e n

"COMPLETE" is shown. Next page S.BUS servo function C o m m o n f u n c t i o n 89 S.BUS Servo Description of function of each parameter

*There are a function which can be used according to the kind of servo, and an impossible function. Displays the ID of the servo whose parameters are to be read. It cannot be changed. Channel of the S.BUS system assigned to the servo. Always assign a channel before use. The direction in which the servo rotates can be changed. ID Channel Reverse Servo type Soft Start Stop Mode Smoother Neutral Oset Speed Control Dead band Travel Adjust Boost When "Retractable" is selected and the servo has been continuously stopped for 30 seconds, the dead band expands and unnecessary hold current due to external force is eliminated. When a new control signal enters, normal operation is resumed. When using the servo as a landing gear servo, select

"Retractable". Also adjust the servo travel to match the landing gear movement range. Restricts operation in the specied direction the instant the power is turned on. By using this setting, the rst initial movement when the power is turned on slowly moves the servo to the specied position. The state of the servo when the servo input signal is lost can be specied. The "Hold" mode setting holds the servo in its last commanded position even if using AM or FM system. This function changes smoothness of the servo operation relative to stick movement changes. Smooth setting is used for normal ight. Select the "OFF" mode when quick operation is necessary such as 3D. The neutral position can be changed. When the neutral oset is large value, the servo's range of travel is restricted on one side. Speeds can be matched by specifying the operating speed. The speed of multiple servos can be matched without being affected by motor fluctuations. This is effective for load torques below the maximum torque. However, note that the maximum speed will not be exceed what the servo is capable of even if the servos operating voltage is increased. The dead band angle at stopping can be specied.

[Relationship between dead band set value and servo operation]

Small Dead band angle is small and the servo is immediately operated by a small signal change. Large Dead band angle is large and the servo does not operate at small signal changes.

(Note) If the dead band angle is too small, the servo will operate continuously and the current consumption will increase and the life of the servo will be shortened. The left and right travels centered about the neutral position can be set independently. The minimum current applied to the internal motor when starting the servo can be set. Since a small travel does not start the motor, it essentially feels like the dead band was expanded. The motor can be immediately started by adjusting the minimum current which can start the motor.

[Relationship between boost set value and servo operation]

Small Motor reacts to a minute current and operation becomes smooth. Large Initial response improves and output torque increases. However, if the torque is too large, operation will become rough. C o m m o n f u n c t i o n 90 Boost ON/OFF Damper OFF : It is the boost ON at the time of low-speed operation.(In the case of usual) ON : It is always the boost ON.(When quick operation is hope) The characteristic when the servo is stopped can be set. When smaller than the standard value, the characteristic becomes an overshoot characteristic. If the value is larger than the standard value, the brake is applied before the stop position. Especially, when a large load is applied, overshoot, etc. are suppressed by inertia and hunting may occur, depending on the conditions. If hunting (phenomena which cause the servo to oscillate) occurs even though the Dead Band, Stretcher, Boost and other parameters are suitable, adjust this parameter to a value larger than the initial value.

[Relationship between damper set value and servo operation]

Small When you want to overshoot. Set so that hunting does not occur. Large When you want to operate so that braking is not applied. However, it will feel like the servo response has worsened.

(Note) If used in the hunting state, not only will the current consumption increase, but the life of the servo will also be shortened. The servo hold characteristic can be set. The torque which attempts to return the servo to the target position when the current servo position has deviated from the target position can be adjusted. This is used when stopping hunting, etc., but the holding characteristic changes as shown below.

[Relationship between stretcher and servo operation]

Small Servo holding force becomes weaker. Large Servo holding force becomes stronger.

(Note) When this parameter is large, the current consumption increases. Stretcher Buzzer When the power supply of a servo is previously turned on at the time of a power supply injection without taking transmit of a transmitter, the buzzer sound of about 2.5 Hz continues sounding from a servo.

(Even when the transmit of a transmitter is taken out previously, a buzzer becomes until the signal of a servo is outputted normally, but it is not unusual.) The transmitter has been turned OFF ahead of a servo power supply The buzzer sound of about 1.25 Hz continues sounding as servo power supply end failure alarm.

(Do not insert or remove the servo connector while the receiver power is ON.A buzzer may sound by incorrect recognition.)

*Buzzer sound is generated by vibrating the motor of a servo. Since current is consumed and a servo generates heat, please do not operate the number more than needed or do not continue sounding a buzzer for a long time. C o m m o n f u n c t i o n 91 MDL-TRANS Model transfer Function Transmission of model data is possible with T10J transmitters. Data transfer is performed by the radio. The MDL-TRANS function works with the current model you are using in the transmitter. As for the receiving transmitter, any data on the current model that is receiving the information will be over-written. Method

(Common)

*T10J does not carry out normal operation during data transfer. CAUTION

NOTE: MDL-TRANS between two T10J radios should be performed within a 2-meter range. Calling the setting screen Call the menu screen from the home screen by pressing the + key for 1 second. 1 second

"MDL-TRANS"

Select from the menu with the Jog key. Open the setting screen by pressing the Jog key. MDL-TRANS Execution of transmission/

reception C o m m o n f u n c t i o n MODE TRANSFERT10J of data origin R E C E I V ET10J w h i c h receives data Model transfer MDL-TRANS between two T10J radios should be performed within 2-meter range. In each T10J, the or key is pressed and it is Select "Execute" with the Jog key. made "TRANSFER" and "RECEIVE". or

"TRANSFER"T10J of data origin

"RECEIVE"T10J which receives data Selection rangeTRANSFER, RECEIVE Hold down the Jog key [ each T10J ]. 1 second )

"COMPLETE" is displayed and the mode transfer is nished. From T8J to T10J, data transfer is possible. In that case, TYPE of T10J on the "RECEIVER" side is changed into "T8J" by key. However, data cannot be sent to T8J from T10J. If data is not being transmitted, the receiving transmitter returns to normal operation 10 seconds after execution. At this time, "Failure" (not transmitting) is displayed. 92 TRAINER Trainer Function

(Common) to match the students level. The trainer function can be used by connecting the instructors transmitter to the students transmitter

the student enters a dangerous situation, control can be immediately switched to the instructor. Four operation modes can be selected at each channel. The trainer switch is set to switch H. When the trainer function is used, the snap roll function is automatically deactivated. Trainer code Teacher Student CAUTION Use the trainer function under the following conditions:

When the instructor uses a T10J transmitter, set the student s transmitter modulation to PPM (for conventional frequency transmitter). (When the student uses a T10J transmitter, the modulation mode does not have to be changed. A PPM signal is always output from the trainer jack.) loose during use. Before ight always conrm that all the instructor and student channels operate normally as set. Always insert the trainer cord as far as it will go and take measures so that the cord will not work Always remove the high frequency module of the student s transmitter. (For module type) Never turn on the student s transmitter power switch. Trainer function operation modes FNC mode: The channel set to this mode can be controlled by the student using the mixing set at the instructor s transmitter. (Student settings are returned to their initial value in advance.) MIX mode: The channel set to this mode is controlled by mixing the instructor and student signals. Correction rudder is applied by the instructor. When this mode is selected, the student s rate is reduced to prevent servo overthrow. The student s rate can also be set. (The student s settings are returned to their initial value in advance.) NOR mode: The channel set to this mode is controlled by signals from the student s transmitter. (The instructor and student settings must be the same.) OFF mode: The channel set to this mode cannot be controlled by the student. It can only be controlled by the instructor. However, channels not provided at the student s transmitter are controlled by the instructor regardless of the above settings. When other models are selected, the trainer function is deactivated, but the channel settings remain. Example of use When the FUNC mode is set at the stick channel, helicopter stick operation training is possible even Control by the instructor is possible by setting only the training channel matched to the student s with a 4EX transmitter (4 channels for aircraft). level to the NORM mode and setting the other channels to the OFF mode. Trainer Cords Instructor 10J 18MZ,14MZ, 14SG, FX-22, 12Z, 12FG, 8FG, 10C, 9C, 7C, 8J, 6J, 4EX Student 10C, 9C, 7C, 6EX, 4EX 18MZ,14MZ, 14SG, FX-22, 12Z, 12FG, 8FG, 10J, 8J, 6J 10J Trainer Cords T12FG (FUTM4405) T12FG (FUTM4405) and 9C

(FUTM4415) Trainer Cords C o m m o n f u n c t i o n 93 Method Calling the setting screen Call the menu screen from the home screen by pressing the + key for 1 second. 1 second

"TRAINER"

Select from the menu with the Jog key. Open the setting screen by pressing the Jog key. Select the item with the Jog key. Function activation Trainer function TRAINER Channel Select Channel setting mode display AUX AUX Select CH mode Display Rate by studentat MIX mode ChannelDisplay MULTICOPTER ACROBATIC 1: AILAileron 6: FLPFlap 1: AILAileron 6: PITPITCH 1: AILAileron 6: FL2Flap2 1: AILAileron 6: AUX 2: ELEElevator7: AI2Aileron2 2: ELEElevator 7: AUX 2: ELEElevator 7: AUX 3: THRThrottle8: AUX 3: MOTMotor 8: AUX 3: THRThrottle8: AUX 4: RUDRudder 4: RUDRudder 4: RUDRudder 5: MODMode 5: FLPFlap 5: GERGear HELICOPTER 2: ELEElevator 7: AUX 3: THRThrottle8: AUX 4: RUDRudder 5: GYRGYRO GLIDER (AF2) Trainer function Function activation Select the "OFF" by pressing the + key or key. When you do not want to use the or function select INH.

*CH9 and CH10 cannot use a trainer function. Mode setting The mode of the channel of hope is chosen by pressing the + key or key. Selection rangeOFF, NOR, FNC, MIX DefaultOFF or C o m m o n f u n c t i o n When MIX mode Select Student rate setting Jog key is pressed in a side and a channel is chosen, rate setting by pressing the + key or key. Range0 100%

Default30%

or 94 Airplane Function The setting screen of each function is called from the following menu. The function when the model type was set to airplane (ACROBATIC) is displayed here. Power ON First set the throttle to slow. Then turn on the power. Home screen To menu screen by holding down the + key When the END key is pressed, the display returns to the home screen. END MENU MENU MENU 1/3 1/3 MENU 2/3 MENU 3/3

1

1

12

123

1 second When the + key is pressed for 1 second, the menu screen is displayed. Selection M o v e t h e c u r s o r

(highlighted) up and down and to the left and right with the Jog key and select the function. The cursor can be moved over several pages. Calling the setting screen Press the Jog key to open the setting screen. A i r p l a n e 95 key LCD key key END key Jog key Refer to "Common Functions"

previously described for a description of this function. Function MENU2/3 TELEMETRY

(P.66) TELEMETRY

(P.66) Telemetry Display Alarm setup Telemetry Display Alarm setup SENSOR SENSOR

(P.83)

(P.83) Telemetry sensor Telemetry sensor SBUS LINK

(P.89)

(P.89) SBUS LINK S.BUS servo set up S.BUS servo set up MDL-TRANS MDL-TRANS

(P.92)

(P.92) Data transfer of another 10J or 8J Data transfer of another 10J or 8J TRAINER

(P.93) TRAINER

(P.93) Trainer Trainer AIL-DIFF

(P.97) Aileron Dierential

(P.98) AIL RUD Aileron Rudder V-TAIL

(P.99) V-Tail

(P.100) GYRO SENS Gyro mixing ELEVON

(P.101) Elevon

(P.102) AILVATOR Ailvator THR NEEDL

(P.103) Throttle Needle Mixing MENU3/3 D/R, EXPO Dual rate EXPO FLAPERON Flaperon AIR-BRK Air brake FLAP ELE Flap Elevator mixing ELE FLAP Elevator Flap mixing FLAP TRIM Flap trim THR.CUT Throttle cut IDLE DOWN Idle down SNAP ROLL Snap roll THR-CURVE Throttle curve PIT-CURVE PIT-curve THR DELAY Throttle delay

(P.104)

(P.106)

(P.108)

(P.110)

(P.111)

(P.112)

(P.113)

(P.115)

(P.116)

(P.117)

(P.118)

(P.119) MENU1/3 MDL-SEL

(P.40) MDL-SEL

(P.40) Model select Model Copy Data Model select Model Copy Data reset RX Link reset RX Link

(P.43) MDL-NAME MDL-NAME

(P.43) Model name User name Model name User name FAIL SAFE FAIL SAFE

(P.45)

(P.45) Fail safe Fail safe

(P.47) REVERSE REVERSE

(P.47) Servo reverse Servo reverse TIMER TIMER

(P.48)

(P.48) Timer Timer

(P.49) SERVO SERVO

(P.49) Servo monitor Servo test Servo monitor Servo test END POINT END POINT

(P.50)

(P.50) End point End point

(P.51) TRIM TRIM

(P.51) Trim reset Trim step Trim reset Trim step SUB TRIM SUB TRIM

(P.52)

(P.52) Sub trim Sub trim

(P.53) P.MIX1-6 P.MIX1-6

(P.53) Program mixing 1 6 Program mixing 1 6 AUX-CHAN AUX-CHAN

(P.56)

(P.56) AUX channel AUX channel PARAMETER PARAMETER

(P.58)

(P.58) Data reset Model type ATL-

Data reset Model type ATL-

trim LCD contrast Back light :

trim LCD contrast Back light :

mode, time, adjustment Home mode, time, adjustment Home display Battery alarm Battery display Battery alarm Battery vibration Buzzer tone Jog vibration Buzzer tone Jog navi Jog light Jog time navi Jog light Jog time Telemetry : mode, unit Speech :

Telemetry : mode, unit Speech :

language, volume Stick position language, volume Stick position alarm alarm A i r p l a n e 96 AIL-DIFF Aileron dierential Function The left and right aileron differential can be adjusted independently. This function is restricted to 2 servo aileron.

(ACROBATIC) CH1 CH7 NOTEAileron Differential cannot be used simultaneously with Flaperon or Elevon. If another function is already active, Others WING mix ON is displayed on the screen. After setting the active function to INH , set the Aileron Dierential function to ACT . Method Calling the setting screen Call the menu screen from the home screen by pressing the +

key for 1 second. 1 second

"AIL-DIFF"

Select from the menu with the Jog key. Open the setting screen by pressing the Jog key. AIL-DIFF ACT/INH Aileron1CH1rate Aileron2CH7rate Select the setting item with the Jog key. When INH is selected, the function cannot be used. To use the function, select ACT. Aileron LAileron stick Left side rate RAileron stick Right side rate A i r p l a n e Aileron Dierential Activating the function Select the "MIX" item and then select the "ACT" by pressing the + key or key. or When you do not use a function, set to the "INH"

side. Aileron rate Select the "RATE-AIL1" item and move the aileron stick to the left and right and adjust the travel of each servo by pressing the + key or key. Range-120 +120%

Default+100%

or When you want to return to the initial value, press the + key and key simultaneously. However, when the polarity is changed only the number returns to the initial value. Adjust the "RATE-AIL2" item in the same way as . 97

(ACROBATIC) AIL RUD Aileron Rudder mixing Function Use this mix when you want to mix the rudders with aileron operation. This allows the aircraft to bank at a steep angle.

Method Calling the setting screen Call the menu screen from the home screen by pressing the +

key for 1 second. 1 second

"AIL RUD"

Select from the menu with the Jog key. Open the setting screen by pressing the Jog key.

When not using this function, select INH. Activating the function Mixing rate Select the setting item with the Jog key. Aileron Rudder Mixing Activating the function Select the "MIX" item and then select the "ON" by pressing the + key or key. or Mixing rate Select the "RATE" item and then adjust the mixing rate by pressing the + key or key. or Range-100 +100%

Default+50%

When you do not use a function, set to the "INH" side. When you want to return the set value to the initial value, press the + key and key simultaneously. However, polarity does not return. A i r p l a n e 98 V-Tail V-TAIL Function This mixing is used with V tail aircraft that combine the elevator and rudder functions. NOTEV Tail cannot be used simultaneously with Elevon or Ailevator. When another function is already activated, Other WING mix ON is displayed on the screen. Set the V tail function to ACT after setting the active function to INH. Method Calling the setting screen Call the menu screen from the home screen by pressing the +

key for 1 second. 1 second

(ACROBATIC)

-tail CH2 (CH4) CH4 (CH2) Elevator Rudder CH2 Servo ELE1 RUD2 CH4 Servo ELE2 RUD1

"V-TAIL"

Select from the menu with the Jog key. Open the setting screen by pressing the Jog key. V-TAIL When INH is selected, the function cannot be used. To use the function, select ACT. Rate adjustment A i r p l a n e Rate adjustment Select the "RATE" item and then adjust the mixing rate by pressing the + key or key. Range-100 +100%

only ELE2 : -50%

Default+50%

or When you want to return the set value to the initial value, press the + key and key simultaneously.However, polarity does not return. Activating the function ELE1 rate ELE2 rate RUD2 rate RUD1 rate Select the setting item with the Jog key. V-TAIL Activating the function Select the "MIX" item and then select the "ACT" by pressing the + key or key. or When you do not use a function, set to the "INH" side. NOTEWe recommend that setting be performed while moving the stick and checking the amount of movement. If the amount of movement is too large, elevator and rudder operation will be compounded and the servo travel range will be exceeded and a dead band in which the servo will not operate may be created. 99 GYRO SENS Gyro sensor Function This function is dedicated mixing for switching the gyro sensitivity and gyro mode (AVCS/

NORMAL) of Futaba airplane use gyros. Up to 3 axes can be set.

Method

(ACROBATIC)

Calling the setting screen Call the menu screen from the home screen by pressing the +

key for 1 second. 1 second

"GYRO SENS"

Select from the menu with the Jog key. Open the setting screen by pressing the Jog key. Activating the function Gain Channel selection Switch direction Gyrotype, Gain rate Select the setting item with the Jog key. GYRO SENS Gyro type Gyro Gain When not using this function, select INH. Sensitivity switch selection Current switch operating direction Swit c h e s t o t h e sensitivity setting screen of each switch direction when the Jog key is pressed. When using a Futaba GYA gyro, select gyro type GY. This switches the gyro sensitivity setting item to mode and sensitivity direct reading display. GYRO SENS Activating the function Select the "MIX" item and then select the

"ON" by pressing the +

key or key. When you do not use a function, set to the or

"INH" side. Sensitivity switch selection Select the "SW" item and then select the switch by pressing the + key or key. or RangeSwA SwHDefaultSwA Sensitivity setting channel selection S e l e c t t h e

"CH" item and t h e n s e l e c t the sensitivity setting channel by pressing the + key or key. or RangeCH5CH5/CH7 CH5/CH8CH5/CH7/CH8 DefaultCH5 Gyro type and sensitivity setting Press the Jog key and select the sensitivity setting screen you want to set and then set type (gyro type) and rate (gyro sensitivity) of each channel by pressing the +key or key.

"type"RangeSTD,GYDefaultSTD

"rate"Range0 100%STD, NOR100 0 AVC100%GYDefault50%STD, 0%GY When you want to return the set value to the initial value, press the + key and key simultaneously. A i r p l a n e 100 ELEVON Elevon Function This mixing is used with delta wing, tailess, and disk shaped airplanes that combine the aileron and elevator functions. Connect the CH1 servo to the left aileron and the CH2 servo to the right aileron.

NOTEElevon cannot be used simultaneously with V-tail or Ailevator functions. You may use Flaperon or Dierential when this function is active. If another function is already active, Other WING mix ON is displayed on the screen. After setting the active function to INH , set the V-tail function to ACT . Method

(ACROBATIC) CH2 CH2 Pitch Roll CH1 CH1 Roll Pitch CH1 servo AIL1 ELE2 CH2 servo AIL2 ELE1 Calling the setting screen Call the menu screen from the home screen by pressing the +

key for 1 second. 1 second

"ELEVON"

Select from the menu with the Jog key. Open the setting screen by pressing the Jog key. Activating the function Aileron1CH1rate Aileron2CH2rate Elevator2CH1rate Elevator1CH2rate Select the setting item with the Jog key. ELEVON Activating the function Select the "MIX" item and then select the "ACT" by pressing the + key or key. or When you do not use a function, set to the "INH" side. ELEVON When INH is selected, the function cannot be used. To use the function, select ACT. Aileron rate LAileron stick Left side rate RAileron stick Right side rate A i r p l a n e Elevator rate Rate set Select the "RATE" item and then adjust the mixing rate by pressing the + key or key. Range-120 +120%

only ELE1 : -100%

Default+100%

or When you want to return the set value to the initial value, press the + key and key simultaneously.However, polarity does not return. NOTEWe recommend that setting be performed while moving the stick and checking the amount of movement. If the amount of movement is too large, elevator and aileron operation will be compounded and the servo travel range will be exceeded and a dead band in which the servo will not operate may be created. 101 AILVATOR Ailvator Function Ailevator mixes both Ailerons and Elevators together. Or the function can be used separate from your ailerons when you have two

elevators as ailerons, using this function can give you a sense of reality.

The servos connect to the receiver CH2 and CH8 output.

(ACROBATIC) CH 6

(CH7) CH 8 CH 2 CH2 servo AIL3 ELE1 CH8 servo AIL4 ELE2 CH 1 CH 2 CH 8 Roll Pitch

NOTEAilevator cannot be used simultaneously with V-tail or Elevon functions. When Other WING mix ON is displayed on the screen, set the ailvator function to ACT after setting the active function to INH. Method Calling the setting screen Call the menu screen from the home screen by pressing the +

key for 1 second. 1 second

"AILVATOR"

Select from the menu with the Jog key. Open the setting screen by pressing the Jog key. Select the setting item with the Jog key. Activating the function AIL3 Rate set AIL4 Rate set ELE2 Rate set ELE1 Rate set AILVATOR When INH is selected, the function cannot be used. To use the function, select ACT. Rate AILVATOR Activating the function Select the "MIX" item and then select the "ACT" by pressing the + key or key. or When you do not use a function, set to the "INH" side. Rate set Select the "RATE" item and then adjust the mixing rate by pressing the + key or key. Range-100 +100%

Default-50%AIL3, AIL4,

-100%ELE2, +100%ELE1 or When you want to return the set value to the initial value, press the + key and key simultaneously.However, polarity does not return. NOTEWe recommend that setting be performed while moving the stick and checking the amount of movement. If the amount of movement is too large, elevator and aileron operation will be compounded and the servo travel range will be exceeded and a dead band in which the servo will not operate may be created. When used as 2 elevator servos specications without aileron operation, set the AIL3 and AIL4 travel to 0%. A i r p l a n e 102

(ACROBATIC) THRNEEDL Throttle Needle mixing Function This function is used when the engine is equipped with a mixture control system (needle control and other mixture adjustments to the engine). The throttle control servo connects to receiver CH8.

NOTEThis cannot be used if Ailevator function is active as they cannot be used simultaneously. AILVATOR mix ON is displayed on the screen. Set the THR NEEDL function to ACT after setting the active function to INH. Method Calling the setting screen Call the menu screen from the home screen by pressing the +

key for 1 second. 1 second

"THR NEEDL"

Select from the menu with the Jog key. Open the setting screen by pressing the Jog key. Select the setting item with the Jog key. Activating the function 5 Point curve set Cursor moves with a THR stick Acceleration rate

When not using this function, select INH. The set-up curve is shown A i r p l a n e Throttle curve Activating the function Select the "MIX"

item and then select the "ON"

by pressing the

+ key or key. When you do not use a function, set or to the "INH" side. 5 point curve setting Select the setting item (P-1 P-5) and then set the travel of each point by pressing the + key or key. DefaultP-1:0%, P-2:25%, P-3:50%, Range0 100%

P-4:75%, P-5:100%

Acceleration rate Select the "ACC" item and adjust the acceleration amount by pressing the + key or key. Range0 100%, Default0%

When you want to return the set value to the initial value, press the + key and key simultaneously. 103 D/R,EXPO Dual rate EXPO Function

(ACROBATIC) D/R The aileron, elevator and rudder channel control surface angle can be switched in 2 steps

EXP This function makes operation more pleasant by changing the operating curve so that servo movement is sluggish or sensitive relative to stick operation near the aileron, elevator, throttle, and rudder neutral position. Adjustments can be made in 2 steps according to the control surface angle.

Switch selectionSW Switches A to H can be selected as the aileron channel, elevator channel, and rudder channel dual rate

(exponential) switch.

Method A i r p l a n e Calling the setting screen Call the menu screen from the home screen by pressing the +

key for 1 second. 1 second

"D/R,EXPO"

Select from the menu with the Jog key. Open the setting screen by pressing the Jog key. Channel selection Dual rate EXPO Switch selection Channel selection/Select the setting item with the Jog key. 104 The channel under selection is underlined. Switch Direction The dual rate and exponential settings are displayed by a curve. Switch No. D/R and EXPO rate display Top rowLeft side down Bottom rowRight side up Channel 1Aileron 2Elevator 3Throttle 4Rudder D/R A channel is chosen by Jog key. Range1, 2, 4 Adjust the rate by moving the cursor to D/R with the Jog key, switching the dual rate switch to the direction you want to set, moving the stick to the left

(down) or right (up) side and pressing the + key or key. Range 0 140%

Default100%

When you want to return the set value to the initial value, press the + key and key simultaneously. Adjust the rate of each direction of the dual rate switch and stick by repeating step EXPO Select the "EXP" item and then select the channel with the Jog key. Range1 4 Moving to another setting item of the same channel is possible by Jog key. Adjust the rate by moving the cursor to EXP with the Jog key, switching the dual rate switch to the direction you want to set, moving the stick to the left

(down) or right (up) side and pressing the + key or key. Range

-100 +100%

Default0%

When you want to return the set value to the initial value, press the + key and key simultaneously. Adjust the rate of each direction of the dual rate switch and stick by repeating step Moving to another setting item of the same channel is possible by Jog key. Switch Change Select the "SW" item and then select the channel with the Jog key. Range1, 2, 4 A switch is chosen by + key or -key. or RangeSwA SwH A i r p l a n e 105 FLAPERON Flaperon Function This mixing function mixes two ailerons and also gives the

surfaces can be raised at the same time. If this function is used together with air brake function, the aircraft speed can be dropped when landing and is effective in narrow places. Connect the left aileron servo to CH1 (AIL) and the right aileron servo to CH6

(FLP).

NOTEOnly the Flaperon, AileronDierential, or Elevon functions can be used. They cannot be turned on simultaneously. When another function is already activated, Other WING mix ON is displayed on the screen. Set the Flaperon function to ACT after setting the active function to INH. Method

(ACROBATIC) CH1 CH6 l e r o n A i Operation Flap Operation CH6 servo CH1 servo Right Aileron Left Aileron Flap1 Flap2 Calling the setting screen Call the menu screen from the home screen by pressing the +

key for 1 second. 1 second A i r p l a n e

"FLAPERON"

Select from the menu with the Jog key. Open the setting screen by pressing the Jog key. FLAPERON Activating the function Aileron1CH1rate Aileron2CH6rate Flap2CH1rate Flap1CH6rate Select the setting item with the Jog key. When INH is selected, the function cannot be used. To use the function, select ACT. Aileron rate LAileron stick Left side rate RAileron stick Right side rate Flap rate 106 Flaperon Activating the function Select the "MIX" item and then select the "ACT" by pressing the + key or key. or When you do not use a function, set to the "INH" side. Aileron rate Select "RATE-AIL1" and operate the aileron stick to the left and right and adjust the travel of each servo by pressing the + key or key. or Range-120 +120%

Default100%

When you want to return the set value to the initial value, press the + key and key simultaneously. However, when the polarity is changed, only the number is returned to the initial value.

(The RATE-AIL 2 item is adjusted in the same way as . When ap trim is used, make the settings shown below. However, set the basic travel with the Flap function in advance.Default0%

Flap rate Select the "RATE-FLP2" item and adjust the Flap2 travel by pressing the + key or key. Range-120 +120%

Default+100%

or When you want to return the set value to the initial value, press the + key and key simultaneously.However, polarity does not return. The RATE-FLP1 item is adjusted in the same way as . However, the RATE-FLP1 side initial value is -100%. CH1 CH1 CH6 CH6 Flaperon ACT When flaperon is active, the ailerons can be controlled by the servos connected to CH1 and CH6. The servo travel can be adjusted by the left and right end points. Air brake ACT The left and right ailerons can be raised (brake operation) and lowered (flap operation) at the same time by setting SW-C to its lowest position. A i r p l a n e 107 AIR-BRK Air brake Function This function is used when the air brake is necessary during landing and is turned on and off by switch C (initial setting).

(ACROBATIC)

Adjustment item for every wing type Display AIL1(1CH) ELEV(2CH) FLAP(6CH) AIL2(7CH) Normal

Elevator Flap

Flaperon Aileron1 Elevator Aileron2

Aileron Dierential Aileron1 Elevator Flap Aileron2 CH2 CH 2 CH 6 CH 1 Method A i r p l a n e Calling the setting screen Call the menu screen from the home screen by pressing the +

key for 1 second. 1 second

"AIR-BRK"

Select from the menu with the Jog key. Open the setting screen by pressing the Jog key. Activating the function AIR-BRK Rate set Delay Rate set 3CH Control set When not using this Function select INH. The display of On/

O is shown when active and assigned to a switch. Switch selection Switch direction Mode Select the setting item with the Jog key. When the LINR operation mode was selected, the current throttle stick position is displayed at the operation reference point and in the bottom row parentheses. 108 Air brake Activating the function Select the "MIX" item and then select the "ON" or "OFF" by pressing the +

key or key. or Rate set Select the "rate" item and adjust the servo travel by pressing the + key or key. or Range-100 +100%

Default+50%ELEV only -10%

When you do not use a function, set to the "INH" side. When you want to return the set value to the initial value, press the + key and key simultaneously. However, polarity does not return. Delay Rate set Select the "delay" item and adjust the elevator operation delay by pressing the + key or key. The amount of delay is large at 100%. Range0 100%Default0%

When you want to return the set value to the initial value, press the + key or and key simultaneously. In the case of change of a switch Switch selection Select the "SW"

item and then select the switch by pressing the

+ key or key. or RangeSwA SwH DefaultSwC In the case of change of a mode Mode S e l e c t t h e

" M O D " i t e m and select the operation mode by pressing the + key or the key. or RangeOFST, LINR DefaultOFST Switch direction Select the ON direction by pressing the + key or key at the ON direction selection item. or Range 2P SWNULL, UP, DOWN 3P SWNULL, UP, UP&D, UP&C, CNTR, C&DN, DOWN Operation reference point setting ("LINR" mode only) Select the operation reference point setting item newly displayed at the bottom row of "MOD" and hold the throttle stick at the air brake start point and set the reference point by pressing the Jog key for 1 second. Range0 100%

When 3CH control is changed at the time of "LINR"

"LINR" mode 3CH control Select the "CH3" item and select control by pressing the +key or key. RangeTHR, SwA SwH, VR, DT5, DT6 DefaultTHR A i r p l a n e 109 FLAPELE Flap Elevator mixing Function This mixing is used to compensate for pitch

(ACROBATIC)

Method Calling the setting screen Call the menu screen from the home screen by pressing the +

key for 1 second. 1 second

"FLAP ELE"

Select from the menu with the Jog key. Open the setting screen by pressing the Jog key. Activating the function Mixing rate Mixing oset rate

When not using this function, select INH. Present flap operating position Select the setting item with the Jog key. Flap ElevatorMixing Activating the function Select the "MIX" item and then select the "ON" by pressing the + key or key. Mixing rate Select the "RATE" item and then adjust the mixing rate by pressing the + key or key. or or When you do not use a function, set to the "INH" side. Range-100 +100%

Default0%

When you want to return the set value to the initial value, press the + key and key simultaneously. A i r p l a n e When changing the mixing reference point Mixing reference point oset setting Select the "OFFSET" item and turn the Flap knob to the point you want to make the mixing reference point and set the reference point by pressing the Jog key for 1 second. Range-100 +100% Default0%

1 second 110 ELE FLAP Elevator Flap mixing Function This mixing is used when you want to apply mixing from elevators

the elevators. When used with Fun Fly and other aircraft, small loops are possible.

(ACROBATIC) Flap CH6 Elevator CH2

"ELE FLAP"

Select from the menu with the Jog key. Open the setting screen by pressing the Jog key. Method Calling the setting screen Call the menu screen from the home screen by pressing the +

key for 1 second. 1 second Activating the function Mixing rate

Switch selection Switch direction Select the setting item with the Jog key. Elevator FlapMixing Activating the function Select the "MIX" item and then select the ON or OFF by pressing the

+ key or key. When you do not use a function, set to the or

"INH" side. When not using this Function select INH. The display of On/

O is shown when active and assigned to a switch. Elevator down side rate Elevator up side rate T h i s c u r s o r p o s i t i o n operates and chooses an elevator stick. Sets the ON/OFF direction of the selected switch. 2P SWNULL, UP, DOWN 3P SWNULL, UP, UP&D, UP&C, CNTR, C&DN, DOWN Switch selection Select the "SW" item and then select the switch by pressing the

+ key or key. RangeSwA SwHDefaultSwC or Switch direction Select the "POSI

" by pressing the

+ key or key at the ON direction selection item. or Range 2P SWNULL, UP, DOWN 3P SWNULL, UP, UP&D, UP&C, CNTR, C&DN, DOWN Mixing rate Select the "RATE" item and then adjust the mixing rate by pressing the + key or key. or Range-100 +100%Default+50%

When you want to return the set value to the initial value, press the + key and key simultaneously. However, polarity does not return. RATE / cursor position operates and chooses an elevator stick. A i r p l a n e 111 FLAP TRIM Flap trim Function This function trims the CH6 VR knob.

(ACROBATIC)

*When the aperon function is activated ( ACT ), this function is turned on automatically. It can be turned on and o independently. Method Calling the setting screen Call the menu screen from the home screen by pressing the +

key for 1 second. 1 second

"FLAP TRIM"

Select from the menu with the Jog key. Open the setting screen by pressing the Jog key. FLAP TRIM Activating the function Flap trim rate Select the setting item with the Jog key. A i r p l a n e When INH is selected, the function cannot be used. To use the function, select ACT. Flap Trim Activating the function Select the "MIX" item and then select the "ACT" by pressing the + key or key. or Flap rate Select the "RATE" item and then adjust the ap rate by pressing the + key or key. Range-100 +100%

Default0%

or When you do not use a function, set to the "INH" side. When you want to return the set value to the initial value, press the + key and key simultaneously. 112 THR.CUT Throttle cut Function This function cuts (stops) the engine or motor by stick operation. At throttle operation, the rate is adjusted to the position which completely cuts the throttle servo or ESC when the throttle is operated. When Thr.Cut is active, the throttle position is held regardless of the throttle stick position.

(ACROBATIC)

Method Calling the setting screen Call the menu screen from the home screen by pressing the +

key for 1 second. 1 second

"THR.CUT"

Select from the menu with the Jog key. Open the setting screen by pressing the Jog key. Mode Activating the function Cut Position rate Throttle Position Switch selection Switch direction Select the setting item with the Jog key. THR.CUT Sets the ON/OFF direction of the selected switch. 2P SWNULL, UP, DOWN 3P SWNULL, UP, UP&D, UP&C, CNTR, C&DN, DOWN A i r p l a n e When not using this Function select INH. The display of On/

Off is shown when active and assigned to a switch. Adjusts the rate to the position that completely cuts the throttle servo or ESC. The THR item can be set when the operation mode is ESC . The number in parentheses is the current throttle stick position. 113 Throttle Cut Mode Select the "MODE" item and then select the mode by pressing the + key or key. or RangeNOR, ESC DefaultNOR

"NOR"Engine plane

"ESC"Electric motor plane Switch selection Select the "SW" item and then select the switch by pressing the + key or key. or RangeSwA SwH DefaultSwA Activating the function Select the "MIX" item and then select the o by pressing the + key or key. or When you do not use a function, set to the

"INH" side. Switch direction Select the "POSI" by pressing the + key or key at the ON direction selection item. or Range 2P SWNULL, UP, DOWN 3P SWNULL, UP, UP&D, UP&C, CNTR, C&DN, DOWN A i r p l a n e Cut Position rate Select the "RATE" item and then select the cht position by pressing the + key or key (motor stop). or In the case of ESC Function release Throttle Position Select the "THR" item and then select the release position by THR stick is lowered and Jog key is pressed for 1 second. Set to a safe low throttle position. Range0 100%

Default15%

It adjusts to the position where an engine is cut. Range-30 0 +30%

Default0%

When you want to return the set value to the initial value, press the + key and key simultaneously. 114 IDLE DOWN Idle down Function This function is linked to the air brake switch and gear switch and lowers the engine idle. It is used when engine idle is set high to prevent the

lower engine idle when landing.

(ACROBATIC)

Method Calling the setting screen Call the menu screen from the home screen by pressing the +

key for 1 second. 1 second

"IDLE DOWN"

Select from the menu with the Jog key. Open the setting screen by pressing the Jog key. IDLE DOWN Activating the function Idle down rate Switch selection Switch direction When not using this Function select INH. The display of On/

O is shown when active and assigned to a switch. Select the setting item with the Jog key. Idle down Activating the function Select the "MIX" item and then select the on or o by pressing the +

key or key. When you do not use a function, set to the or

"INH" side. Sets the ON/OFF direction of the selected switch. 2P SWNULL, UP, DOWN 3P SWNULL, UP, UP&D, UP&C, CNTR, C&DN, DOWN Switch selection Select the "SW" item and then select the switch by pressing the

+ key or key. RangeSwA SwHDefaultSwC or Switch direction Select the "POSI" by pressing the

+ key or key at the ON direction selection item. Range 2P SWNULL, UP, DOWN 3P SWNULL, UP, UP&D, UP&C, CNTR, C&DN, DOWN Idle down rate Select the "RATE" item and then adjust the idle down rate by pressing the + key or key. or Range0 40%

Default0%

When you want to return the set value to the initial value, press the + key and key simultaneously. The idle down amount is usually 10% 20%. Hold down the aircraft and set the throttle switch to the maximum slow position while the engine is running and adjust the idle drop amount while turning the switch on and o. A i r p l a n e 115 SNAP ROLL Snap roll Function This function performs snap roll by switch (SwH).

NOTE The trainer function cannot be turned on simultaneously with this function. If the trainer function is active, trainer ACT is displayed on the screen. After setting the trainer function to INH , turn on this function. Method

(ACROBATIC) Direction Switch SW2 SW1 1: R/U 2: L/U 3: R/D 4: L/D Calling the setting screen Call the menu screen from the home screen by pressing the +

key for 1 second. 1 second

"SNAP ROLL"

Select from the menu with the Jog key. Open the setting screen by pressing the Jog key. Activating the function SNAP ROLL Snap roll direction When INH is selected, the function cannot be used. To use the function, select ACT. Safe mode set Direction Switch selection Rate set Select the setting item with the Jog key. Idle down Activating the function Select the "MIX" item and then select the "OFF" by pressing the + key or key. or When you do not use a function, set to the "INH"

side. Safe mode set Select the "SAFE-MODE"

item and then select the mode by pressing the +

key or key. Range FREE, CH5+, CH5-

DefaultFREE A i r p l a n e 116 D i r e c t i o n s w i t c h selection Select the "DIRC-SW1"

and "DIRC-SW2" item and select each switch by pressing the + key or key. Range NULL, SwA SwH DefaultNULL Servo Rate set Switch the DIRC-SW1 or DIRC-

SW2 in the direction you are wanting to adjust by pressing the + key or key at the AIL , ELE , and RUD items. Range-120 +120%

Set the R/U, L/U, R/D, and L/D directions. When a 3 position switch was selected at DIRC-SW1 setting, 1:R/U, 2:L/

U, 3:R/D switching is possible with 1 switch. At this time, DIRC-SW2 cannot be selected. Safe mode setting can set the direction of the landing gear switch. When CH+ was selected, the safety device sets the landing gear switch to the rear position and the snap switch is not effective even if operated. When the landing gear switch is in the forward position, operation is possible. When CH5-

was selected, the safety device operates and the snap switch is ineective even if operated. When the landing gear switch is in the rear position, operation is possible. When FREE was selected: The safety device does not operate regardless of the switch direction. THR-CURVE Throttle curveAirplane Function This function sets a 5 point throttle curve so that the engine/motor speed relative to movement of the

(ACROBATIC) However, this function cannot be used when the throttle EXP function was set. When this function is set, the throttle EXP function cannot be used. Method Calling the setting screen Call the menu screen from the home screen by pressing the +

key for 1 second. 1 second

"THR-CURVE"

Select from the menu with the Jog key. Open the setting screen by pressing the Jog key. THR-CURVE Activating the function Switch selection 5 point curve set Select the setting item with the Jog key. When not using this function, select INH. The set-up curve is shown Present switch position Throttle curve Activating the function Select the "MIX" item and then select the

"ON" by pressing the +

key or key. When you do not use a function, set to the or

"INH" side. Switch selection Select the "SW" item and then select the switch by pressing the

+ key or key. RangeSwA SwHDefaultSwE or 5 point curve set By Jog key, either of P-1 to P-5 is chosen. The + key or - key is pressed and a rate is set up. or Range0 100%

DefaultP-1:0%, P-2:25%, P-3:50%, P-4:75%, P-5:100%

A i r p l a n e 117 PIT-CURVE Pitch curveAirplane Function This function is a function for the variable pitch propellers of an airplane.

(ACROBATIC)

Method Calling the setting screen Call the menu screen from the home screen by pressing the +

key for 1 second. 1 second

"PIT-CURVE"

Select from the menu with the Jog key. Open the setting screen by pressing the Jog key. PIT-CURVE Activating the function Switch selection 5 point curve set Select the setting item with the Jog key. When not using this function, select INH. Channel selection The set-up curve is shown Present switch position PIT-curve Activating the function Select the "MIX" item and then select the

"ON" by pressing the +

key or key. When you do not use a function, set to the or

"INH" side. 5 point curve set By Jog key, either of P-1 to P-5 is chosen. The +

key or - key is pressed and a rate is set up. Range-100 DefaultP-1:-100%, P-2:-50%, P-3:0%,

+100%

or P-4:+50%, P-5:+100%

Switch selection Select the "SW" item and then select the switch by pressing the

+ key or key. RangeSwA SwHDefaultSwE or When a channel is changed Channel selection Select the "CH" item and then select the channel by pressing the + key or key. or Range8CH5CH Default8CH A i r p l a n e 118 THR DELAY Throttle delay Function When this function is used, the throttle servo operating speed can be slowed down. Perfect for turbojet engine throttle control, etc.

(ACROBATIC) Method Calling the setting screen Call the menu screen from the home screen by pressing the +

key for 1 second. 1 second

"THR DELAY"

Select from the menu with the Jog key. Open the setting screen by pressing the Jog key. THR DELAY Activating the function Delay Rate set Select the setting item with the Jog key. When INH is selected, the function cannot be used. To use the function, select ACT. Throttle delay rate It can be set to slow the servo movement up to +100%

A i r p l a n e THR DELAY Activating the function Select the "MIX" item and then select the "ACT" by pressing the + key or key. or When you do not use a function, set to the "INH" side. Delay Rate set Select the "RATE" item and then adjust the rate by pressing the + key or key. Range0 100%

Default0%

or When you want to return the set value to the initial value, press the + key and key simultaneously. 119 HELICOPTER Function The setting screen of each function is called from the following menu. The function when the model type was set to helicopter is displayed here. PowerON To menu screen by holding down the + key First set the throttle to slow. Then turn on the power. Home screen When the END key is pressed, the display returns to the home screen. END MENU MENU MENU 1/3 1/3 MENU 2/3 MENU 3/3

1

1

12

123

H e l i c o p t e r 120 1 second When the + key is pressed for 1 second, the menu screen is displayed. Selection M o v e t h e c u r s o r

(highlighted) up and down and to the left and right with the Jog key and select the function. The cursor can be moved over several pages. Calling the setting screen Press the Jog key to open the setting screen. key LCD key key END key Jog key Condition switching at each setting screen Press the jog button for 1 second. When setting conditions with the following function, each setting can be made by switching the condition by pressing the Jog key for 1 second. Throttle curve, Pitch curve, Pitch Rudder, Gyro sens, HI/

LO-Pitch, OFFSET, Throttle MIX, THR Needle, Swash MIX Refer to "Common Functions"

previously described for a description of this function. Function MENU2/3

(P.66) TELEMETRY TELEMETRY

(P.66) Telemetry Display Alarm setup Telemetry Display Alarm setup

(P.83) SENSOR SENSOR

(P.83) Telemetry sensor Telemetry sensor SBUS LINK SBUS LINK

(P.89)

(P.89) S.BUS servo set up S.BUS servo set up

(P.92) MDL-TRANS MDL-TRANS

(P.92) Data transfer of another 10J or 8J Data transfer of another 10J or 8J TRAINER TRAINER

(P.93)

(P.93) Trainer Trainer C O N D I T I O N ( I d l e - u p Throttlehold)

(P.122) Condition SWASH AFRH-1 removes

(P.123) Swash AFR SWH.MIX Swash MIXing SWH.RING Swash RING OFFSET Trim oset DELAY Delay THR.CHT Throttle cut

(P.124)

(P.126)

(P.127)

(P.128)

(P.129) MENU1/3

(P.40) MDL-SEL MDL-SEL

(P.40) Model select Model Copy Data Model select Model Copy Data reset RX Link reset RX Link

(P.43) MDL-NAME MDL-NAME

(P.43) Model name User name Model name User name FAIL SAFE FAIL SAFE

(P.45)

(P.45) Fail safe Fail safe

(P.47) REVERSE REVERSE

(P.47) Servo reverse Servo reverse TIMER TIMER

(P.48)

(P.48) Timer Timer

(P.49) SERVO SERVO

(P.49) Servo monitor Servo test Servo monitor Servo test END POINT END POINT

(P.50)

(P.50) End point End point

(P.51) TRIM TRIM

(P.51) Trim reset Trim step Trim reset Trim step SUB TRIM SUB TRIM

(P.52)

(P.52) Sub trim Sub trim

(P.53) P.MIX1-6 P.MIX1-6

(P.53) Program mixing 1 6 Program mixing 1 6 AUX-CHAN AUX-CHAN

(P.56)

(P.56) AUX channel AUX channel PARAMETER

(P.58) PARAMETER

(P.58) Data reset Model type ATL-

Data reset Model type ATL-

trim LCD contrast Back light :

trim LCD contrast Back light :

mode, time, adjustment Home mode, time, adjustment Home display Battery alarm Battery display Battery alarm Battery vibration Buzzer tone Jog vibration Buzzer tone Jog navi Jog light Jog time navi Jog light Jog time Telemetry : mode, unit Speech :

Telemetry : mode, unit Speech :

language, volume Stick position language, volume Stick position alarm alarm MENU3/3 GYRO SENS Gyro mixing D/R, EXPO Dual rate EXPO THR-CURVE Throttle curve PIT-CURVE Pitch curve REVO.MIX Revolution mixing (PIT to RUD) THR HOLD Throttlehold GOVERNOR Governor mixing HOV-THR Hovering Throttle HOV-PIT Hovering Pitch HI/LO-PIT HI/LO-pitch trim THR-MIX Swash Throttle mixing THR-NEEDL Throttle Needle mixing

(P.131)

(P.132)

(P.134)

(P.136)

(P.138)

(P.140)

(P.141)

(P.143)

(P.144)

(P.145)

(P.146)

(P.147) H e l i c o p t e r 121 CONDITION Condition select (Idle-upThrottlehold) (HELICOPTER) Function The condition switches (idle up 1/2/3 and throttle hold switch) are not operative at initial setting. Switch setting is performed in advance with the condition select function.

Method Calling the setting screen Call the menu screen from the home screen by pressing the +

key for 1 second. 1 second

"CONDITION"

Select from the menu with the Jog key. Open the setting screen by pressing the Jog key. CONDITION Idle-up setting Throttlehold setting Select the setting item with the Jog key. Activating thefunction Switch direction Switch selection When not using this Function select INH. The display of On/

O is shown when active and assigned to a switch. H e l i c o p t e r Condition select Activating the function Select the "INH" item of the condition you want to use and set it to "ON" or "OFF" by pressing the

+ key or key. Set conditions you do not want to use to "INH". In the case of change of a switch Switch selection A cursor is moved to

"Switch selection" and a switch is changed by key or key. or RangeSwA SwH DefaultSwEIDLE-UP1/2 SwFIDLE-UP3SwGTHR-HOLD 122 or Switch direction A cursor is moved to

"Switch direction" and a switch direction is changed by key or key. or Range 2P SWNULL, UP, DOWN 3P SWNULL, UP, UP&D, UP&C, CNTR, C&DN, DOWN When swash type is H-1, this setting screen is not displayed.

(HELICOPTER) SWASH AFR Swash AFR Function This is the adjustable function rate (AFR) func-

tion when HR3, H-3, HE3, HN3, H-2, H-4, or H4X is selected as the swash type. The ailerons, eleva-

tors, and pitch steering angle and direction can be adjusted. Method Calling the setting screen Call the menu screen from the home screen by pressing the +

key for 1 second. 1 second

"SWASH AFR"

Select from the menu with the Jog key. Open the setting screen by pressing the Jog key. Select the setting item with the Jog key. SWASH AFR Rete Depending on the swash type the screen display is dierent. When the polarity is changed, the direction of operation is reversed. NOTEIf the steering angle is too large, linkage binding may occur . Swash AFR Travel adjustment of each function Select each function item of "RATE" and set the rate by pressing the + key or key. or Range-100 +100%

Default+50%

When you want to return the set value to the initial value, press the + key and key simultaneously. However, polarity does not return. H e l i c o p t e r 123 SWH. MIX Swash mixing Function This mixing is used to correct the bad tendencies of the swash plate in the aileron direction and elevator direction relative to aileron, elevator, and pitch operations. It adjusts the rate of the direction that requires correction so that the servo operates

(HELICOPTER) smoothly in the proper direction relative to each operation.

Example of use: Using to correct bad roll tendencies AIL ELE is set to ON. ACTION/ON is common to all conditions. The rate of unused conditions is set to 0%. When the nose drops at right roll and the right side rate is adjusted in the "+"

direction, the elevators move to the up side when the right aileron is deected. Left roll can be adjusted by left side rate. However, since the left and right ailerons polarity and elevators operating direction relationship is reversed; check the correction direction by swash plate operation. Method Calling the setting screen Call the menu screen from the home screen by pressing the +

key for 1 second. 1 second

"SWH.MIX"

Select from the menu with the Jog key. Open the setting screen by pressing the Jog key. SWH.MIX 1 2 Select the setting item with the Jog key. Condition Mixing master direction Mixing rate Activating the function SWH.MIX 1 2 Present condition Rate When not using this function, select INH. H e l i c o p t e r 124 Swash mixing Activating the function Select the "MIX" item and then select the

"ON" by pressing the + key or key. or When you are not using a function, set this to INH. Setup of rate Select the "RATE" item and then adjust the mixing rate by pressing the + key or key. Range-100 +100%

Default0%

When you want to return the set value to the initial value, press the + key and key simultaneously. ON/OFF of a function, Setup of rate, and a trim, Jog key is pushed and setting condition can be chosen. Range NORM, IDL1, IDL2, IDL3, HOLD H e l i c o p t e r 125 SWH.RING Swash ring Function This swash mixing function limits swash travel to prevent damage to the switch linkage due to si-

multaneous aileron and elevator operation. If is ef-

fective in 3D aerobatics with a large steering angle. Method Aileron and elevator stick operation is limited to within the circle (swash mixing) in the gure shown at the right. (When rate is 100%)

(HELICOPTER) SwashRing 50%

100%

n o i t a r e p o E L E AIL operation Calling the setting screen Call the menu screen from the home screen by pressing the +

key for 1 second. 1 second

"SWH.RING"

Select from the menu with the Jog key. Open the setting screen by pressing the Jog key. SWH.RING Activating the function Swash Ring rate Select the setting item with the Jog key. Adjusts the operable range (swash mixing) of the aileron and elevator sticks. When not using this function, select INH. Displays the actual aileron and elevator combined travel when the stick is manipulated. Swash Ring Activating the function Select the "MIX" item and then select the

"ON" by pressing the + key or key. or When you do not use a function, set to the "INH" side. H e l i c o p t e r 126 Setup of rate Select the "RATE" item and then adjust the mixing rate by pressing the + key or key. Range50 200%

Default100%

or When you want to return the set value to the initial value, press the + key and key simultaneously. NOTEAdjust the swash mixing rate to the largest swash inclination at which the linkage rod does not interfere. Trim oset OFFSET Function If this trim offset function is used, independent trim adjustments can be made during hovering and in the air. This function can offset the ailerons, elevators, and rudder neutral position by linking to the set switch or condition. A habit that tends to appear from the standpoint of helicopter characteristics when flying at high speed is possible. This function can correct this habit.

Method

(HELICOPTER)

Calling the setting screen Call the menu screen from the home screen by pressing the +

key for 1 second. 1 second

"OFFSET"

Select from the menu with the Jog key. Open the setting screen by pressing the Jog key. Select the setting item with the Jog key. Activating the function Switch direction, Selection of condition Oset rate Switch selection Trim oset OFFSET When not using this Function select INH. The display of On/O is shown when active and assigned to a switch. Present condition When "Cond" is chosen, if Jog key is pushed for 1 second, it will change to each condition setting screen. Activating the function Select the "MIX" item and then select the

"ON" o r "OFF" b y pressing the + key or key. When you do not use a function, set to the or

"INH" side. Switch direction and condition selection Select the switch direction and condition you want to set at the switch direction and condition items. or Switch selection Select the "SW" item and then select the switch by pressing the

+ key or key. or RangeCond, SwA SwH Oset rate Select the "RATE" item and then adjust the oset rate by pressing the + key or key. Range-120 +120%

Default0%

When you want to return the set value to the initial value, press the + key and key simultaneously. H e l i c o p t e r 127 DELAY Delay Function This function prevents sudden offset changes

hold functions are turned on and off.

(HELICOPTER)

Method Calling the setting screen Call the menu screen from the home screen by pressing the +

key for 1 second. 1 second

"DELAY"

Select from the menu with the Jog key. Open the setting screen by pressing the Jog key. Select the setting item with the Jog key. DELAY Delay rate Linked to the offset, revolution mixing, and throttle hold functions and turned "ON". The delay is maximum at 100%. Delay rate Delay rate set Select the "RATE" item and then adjust the delay rate by pressing the + key or key. up or Range0 100%

Default0%

When you want to return the set value to the initial value, press the + key and key simultaneously. H e l i c o p t e r 128 THR.CUT Throttle cut Function This function cuts (stops) the engine or motor by stick operation. At throttle operation, the rate is adjusted to the position which completely cuts the throttle servo or ESC when the throttle is operated. At function operation, this position is held regardless of the throttle stick position.

(HELICOPTER)

Method Calling the setting screen Call the menu screen from the home screen by pressing the +

key for 1 second. 1 second

"THR.CUT"

Select from the menu with the Jog key. Open the setting screen by pressing the Jog key. Mode Activating the function Cut Position rate Throttle Position Switch selection Switch direction Select the setting item with the Jog key. THR.CUT Sets the ON/OFF direction of the selected switch. 2P SWNULL, UP, DOWN 3P SWNULL, UP, UP&D, UP&C, CNTR, C&DN, DOWN When not using this Function select INH. The display of On/

Off is shown when active and assigned to a switch. Adjusts the rate to the position that completely cuts the throttle servo or ESC. The "THR" item can be set when the operation mode is "ESC". The number in parentheses is the current throttle stick position. H e l i c o p t e r 129 Throttle Cut Mode Select the "MODE" item and then select the mode by pressing the + key or key. or RangeNOR, ESC DefaultNOR

"NOR"Engine plane

"ESC"Electric motor plane Switch selection Select the "SW" item and then select the switch by pressing the + key or key. or RangeSwA SwH DefaultSwA Activating the function Select the "MIX" item and then select the o by pressing the + key or key. or When you do not use a function, set to the

"INH" side. Switch direction Select the "POSI" by pressing the + key or key at the ON direction selection item. or Range 2P SWNULL, UP, DOWN 3P SWNULL, UP, UP&D, UP&C, CNTR, C&DN, DOWN Cut Position rate Select the "RATE" item and then select the cht position by pressing the + key or key (motor stop). or In the case of ESC Function release Throttle Position Select the "THR" item and then select the release position by THR stick is lowered and Jog key is pressed for 1 second. It adjusts to the position where an engine is cut. Range-30 0 +30%

Default0%

When you want to return the set value to the initial value, press the + key and key simultaneously. Set to a safe low throttle position. Range0 100%

Default15%

H e l i c o p t e r 130 For helicopters Gyro mixing GYRO SENS Gyro mixing Function This mixing adjusts the gyro sensitivity from the transmitter. The AVCS gyro (GY mode) or normal gyro (STD mode) can be selected. Up to 3 axes can be set.

(HELICOPTER) Method Calling the setting screen Call the menu screen from the home screen by pressing the +

key for 1 second. 1 second

"GYRO SENS"

Select from the menu with the Jog key. Open the setting screen by pressing the Jog key. Activating the function Gain channel selection Switch direction Gyro type, Gain rate Select the setting item with the Jog key. GYRO SENS When not using this function, select INH. Gain switch direction Present switch position Switches to the sensitivity setting screen of each switch direction when the Jog key is pressed. When a Futaba GY gyro is used, gyro type "GY" is selected. This switches the gyro sensitivity Gyro type Gyro Gain set setting item to the mode and sensitivity direct reading display. Gyro setup Activating the function Select the "MIX" item and then select the

"ON" by pressing the +

key or key. When you do not use a function, set to the or

"INH" side. Gain switch selection Select the "SW" item and then select the switch by pressing the

+ key or key. or RangeCond, SwA SwH Gain channel selection S e l e c t t h e

"CH" item and t h e n s e l e c t the sensitivity setting channel by pressing the + key or key. or RangeRUD, RUD/AIL, RUD/ELE, RUD/AIL/ELE DefaultRUD Gyro type and sensitivity setting Press the Jog key and select the sensitivity setting screen you want to set and then set "type" (gyro type) and "rate" (gyro sensitivity) of each channel by pressing the +key or key.

"type"RangeSTD,GYDefaultSTD

"rate"Range0 100%STD, NOR100 0 AVC100%GYDefault50%STD, 0%GY When you want to return the set value to the initial value, press the + key and key simultaneously. H e l i c o p t e r 131 D/R,EXPO Dual rate EXPO Function

(HELICOPTER) D/R The aileron, elevator and rudder channel control surface angle can be switched in 2 steps

EXP This function makes operation more pleasant by changing the operating curve so that servo movement is sluggish or sensitive relative to stick operation near the aileron, elevator, throttle, and rudder neutral position. Adjustments can be made in 2 steps according to the control surface angle.

Switch selectionSW Switches A to H can be selected as the aileron channel, elevator channel, and rudder channel dual rate

(exponential) switch.

Method Calling the setting screen Call the menu screen from the home screen by pressing the +

key for 1 second. 1 second

"D/R,EXPO"

Select from the menu with the Jog key. Open the setting screen by pressing the Jog key. H e l i c o p t e r 132 Channel selection Switch direction Dual rate EXPO Switch selection Channel selection/Select the setting item with the Jog key. Jog key is pushed for 1 second, a condition screen will change. The channel under selection is underlined. present switch position The dual rate and exponential settings are displayed by a curve. Channel 1Aileron 2Elevator 4Rudder Switch number Rate Dual rate Channel selection A channel is chosen by Jog key. Range1, 2, 4 Switch direction Select the "No" item and then select the switch direction or condition by pressing the + key or key. or D/R Setup of rate Select each function item of "D/R" and set the rate by pressing the + key or key. or Range0 140% Default100%

When you want to return the set value to the initial value, press the + key and key simultaneously. Adjust the rate of each direction of the dual rate switch and stick by repeating step EXPO Channel selection A channel is chosen by Jog key. Range1, 2, 4 Switch direction Select the "No" item and then select the switch direction or condition by pressing the + key or key. or Moving to another setting item of the same channel is possible by Jog key. EXP Setup of rate Select the "EXP" item and then adjust the rate by pressing the + key or key. or Range-100 +100%Default0%

When you want to return the set value to the initial value, press the + key and key simultaneously. Adjust the rate of each direction of the dual rate switch and stick by repeating step Switch Change Channel selection Select the "SW" item and then select the channel with the Jog key. Range1, 2, 4 Moving to another setting item of the same channel is possible by Jog key. Switch selection A switch or Cond is chosen by + key or key. or RangeSwA SwH, Cond possible for every condition. When "Cond" is chosen, a setup is H e l i c o p t e r 133 THR-CURVE Throttle curveFor helicopters Function The throttle curve function sets a 5 point curve in relation to the throttle stick movement and adjusts each point over the 0 100% range so that the

(HELICOPTER) Normal throttle curve adjustment method The normal throttle curve creates a basic throttle curve centered near hovering. This curve is adjusted together with the normal pitch curve so that engine speed is constant and up/down control is easiest. The normal throttle function is always on. Idle up 1/2/3 throttle curve adjustment method The idle up curves are set so that the engine maintains a constant speed even when the pitch is reduced during ight. Curves matched to the purpose such as loop, roll and 3D are created and idle up curves 1/2/3 are by aerobatics. CAUTIONS Operation precautionsWhen starting the engine, always set idle up sticks 1/2/3 to OFF and start the engine at idling. Method Calling the setting screen Call the menu screen from the home screen by pressing the +

key for 1 second. 1 second

"THR-CURVE"

Select from the menu with the Jog key. Open the setting screen by pressing the Jog key. THR-CURVE Activating the function Setting condition 5point curve rate Select the setting item with the Jog key. RatePresent condition When not using this Function select INH. The display of On/

Off is shown when active and assigned to a switch. A display when normal is "---"

alwaysON. The THR-CURVE settings are displayed by a curve. H e l i c o p t e r 134 Throttle curve Activating the throttle curves (ID1/2/3) Select the "MIX" item and set to

"ON" or "OFF" by pressing the +

key or key. For the normal condition, "---" is displayed. (Always ON) When you do not want to use an idle up curve, set to or

"INH". 5 point curve setting Select the setting item of each point (P-1 P-5) with the Jog key and set the travel of each point by pressing the + key or key. Range0 100%

or RangeNOR, ID1, ID2, ID3 Default P-5: 100%

P-4: 75%

P-3: 50%

P-2: 25%

P-1: 0%

When you want to return the set value to the initial value, press the + key and key simultaneously. Curve copying method Select the "CND" item and switch to the curve copy mode by pressing the Jog key. Press the + key or key and select the copy destination condition. or Copy the condition by pressing the Jog key for 1 second. 1 second Throttle curve setting examples

100 75 50 25 E T A R The example of a setting P5=100.0%

P4= 65.0%

P3= 50.0%

P2= 30.0%

P1= 0.0%

100 75 50 25 E T A R The example of a setting P5=100.0%

P4= 75.0%

P3= 50.0%

P2= 54.0%

P1= 56.0%

100 75 50 25 E T A R The example of a setting P5=100.0%

P4= 75.0%

P3= 65.0%

P2= 65.0%

P1= 67.0%

0 P1 P2 P4 P5 P3 STICK Normal 0 P1 P2 P4 P5 P3 STICK Idle-up1 0 P1 P2 P4 P5 P3 STICK Idle-up2 NOTESet the actual value of the throttle curve according to the fuselage specications. H e l i c o p t e r 135 PIT-CURVE Pitch curve For helicopters Function The pitch curve function allows setting by a 5 point curve in relation to throttle stick movement and adjustment of each point over the -100%

+100% range so that the pitch enters the optimum

(HELICOPTER)

NOTEWhen the hold switch is on, the hold function has priority even though an idle up switch is in any position. Normal curve adjustment method The normal pitch curve creates a basic pitch curve centered near hovering. This curve is adjusted together with the throttle pitch curve so that engine speed is constant and up/down control is easiest. Idle up 1/2/3 curve adjustment method The high side pitch curve sets the maximum pitch that does not apply a load to the engine. The low side pitch curve is created to match the purpose such as loop, roll, and 3D. The idle up 1/2/3 curves are used by aerobatics. Throttle hold curve adjustment method The throttle hold curve is used when performing auto rotation dives. Set the intermediate pitch to match the stick work at pitch up. Method Calling the setting screen Call the menu screen from the home screen by pressing the +

key for 1 second. 1 second H e l i c o p t e r

"PIT-CURVE"

Select from the menu with the Jog key. Open the setting screen by pressing the Jog key. PIT-CURVE Activating the function Condition 5point curve rate Select the setting item with the Jog key. RatePresent condition 136 When not using this Function select INH. The display of On/

O is shown when active and assigned to a switch. When normal,"---" (always ON) is displayed. The PIT-CURVE settings are displayed by a curve. Pitch curve Activating the pitch curvesID1/2/3, HLD Select the "MIX" item and then select the "ON" or "OFF" by pressing the + key or key. For the normal condition, "---" is displayed. (Always ON) When you do not want to use an idle up, hold curve, set or to "INH". 5 point curve setting Select the setting item of each point (P-1 P-5) with the Jog key and set the travel of each point by pressing the + key or key. Range-100 +100%

or RangeNOR, ID1, ID2, ID3, HLD Default P-5: +100%

P-4: +50%

P-3: 0%

P-2: -50%

P-1: -100%

When you want to return the set value to the initial value, press the + key and key simultaneously. Curve copying method Select the "CND" item and switch to the curve copy mode by pressing the Jog key. Press the + key or key and select the copy destination condition. or Copy the condition by pressing the Jog key for 1 second. 1 second Pitch curve setting examples

+100 E T A R

+50 0

-50

-100 P1 The example of a setting P5= +40%

P4= +10%

P3= -10%

P2= -40%

P1= -70%

P2 P3 STICK P4 P5 Idle-up1

+100

+50 E T A R 0

-50

-100 P1 The example of a setting P5= +40%

P4= +10%

P3= -10%

P2= -50%

P1= -80%

P2 P3 STICK P4 P5 Idle-up2 NOTESet the actual value of the pitch curve according to the fuselage specications.

+100 E T A R

+50 0

-50

-100 P1

+100

+50 E T A R 0

-50

-100 P1 The example of a setting P5= +70%

P4= +50%

P3= +6%

P2= -40%

P1= -70%

P2 P3 STICK P4 P5 Normal The example of a setting P5= +100%

P4= +50%

P3=

0%

P2= -50%

P1= -100%

P2 P3 STICK P4 P5 Hold H e l i c o p t e r 137 REVO.MIX Pitch Rudder mixing Function

the pitch of the tail rotor to suppress the reaction torque (force that attempts to swing the helicopter in the direction opposite the direction of rotation of the main rotor) generated by the main rotor pitch and speed. It is adjusted so that the pitch of the tail rotor is also changed when the main rotor pitch changes and reaction torque appears and so that the nose does not swing to the left and right. However, when the AVCS mode is used with a GY

(HELICOPTER)

Adjustment procedure First, trim at hovering and then adjust the neutral position. Normal pitch rudder mixing Throttle low side (slow while hovering) adjustment Repeatedly hover from take o and land from hovering at a constant rate matched to your own rhythm, and adjust pitch rudder mixing so that the nose does not deect when the throttle is raised and lowered. If the nose points to the left when landing from hovering or points to the right when taking o, when hovering stabilizes and the stick moves to the neutral position, low side mixing rate is probably too large and when the nose points in the opposite direction, low side rate is probably too small. However, when landing, the direction of the nose may not stabilize depending on the state on the ground. The direction of the nose may also become unstable when rotation of the rotor does not rise. Throttle high (up to climbing from hovering and diving hovering) adjustment Repeat up to climbing from hovering and diving hovering matched to your own rhythm and adjust pitch rudder mixing so that the nose does not deect to the left and right when the throttle is raised and lowered. If the nose points to the right when climbing from hovering, the high side mixing rate is too large and if the nose points to the right, the mixing rate is too small. Repeat climbing and diving and make adjustment while taking the balance. idle-up1/2,3Pitch Ruddermixing This mixing sets the mixing rate so that the rudder direction is straight forward at high speed ight. Method Calling the setting screen Call the menu screen from the home screen by pressing the +

key for 1 second. 1 second

"REVO.MIX"

Select from the menu with the Jog key. Open the setting screen by pressing the Jog key. H e l i c o p t e r 138 REVO.MIX Activating the function Selection of condition High side Setup of rate Low side Setup of rate When not using this function, select INH. present switch position Select the setting item with the Jog key. Rate Pitch Ruddermixing or Activating the function Select the "MIX"

i t e m a n d t h e n select the "ON" by pressing the + key or key. When you do not use a function, set to the "INH" side. Setup of rate Select each function item of "HI"or

"LO" and set the rate by pressing the

+ key or key. Selection of condition Select the "CND" item and selection of condition by pressing the + key or key. or RangeNORM, IDL1/2, IDL3 or Range-100 +100%

Default(NORM)-20%(LOW)+20%(HIGH) Default(IDL1/2/3)0%(LOW)0%(HIGH) When you want to return the set value to the initial value, press the + key and key simultaneously. H e l i c o p t e r 139 THR HOLD Throttle hold Function The throttle hold function fixes or stops the engine throttle position by hold switch operation during an auto rotation dive. Operation can be set within the -50% +50% range based on the

(HELICOPTER) throttle trim position. The switch is changed at the conditions selection screen. (Initial setting: SwG) CAUTIONS NOTEPriority is given to throttlehold over idle-up. Method Calling the setting screen Call the menu screen from the home screen by pressing the +

key for 1 second. 1 second

"THR HOLD"

Select from the menu with the Jog key. Open the setting screen by pressing the Jog key. THR HOLD Activating the function hold throttle position When not using this Function select INH. The display of On/

Off is shown when active and assigned to a switch. Select the setting item with the Jog key. Throttle hold Activating the function Select the "MIX" item and then select the "ON" or "OFF" by pressing the + key or key. or H e l i c o p t e r When you do not use a function, set to the "INH" side. Function ACT INH is linked to condition THR-HOLD, and can be set at any screen. 140 Hold throttle position Select the "RATE" item and then adjust the rate by pressing the + key or key. or Range-50 +50%

Default0%

When you want to return the set value to the initial value, press the + key and key simultaneously. Hold position adjustment method When you want to lower the engine idling, set to the "+" direction and adjust so that the carburetor is full open. When maintaining idling, set the throttle stick to the slow position and turn the hold switch on and o and set to the number at which the servo does not operate. NOTEWhen connecting the throttle linkage, lower the digital trim to the slowest and adjust so that the carburetor is full open. GOVERNOR Governor mixing Function When a governor (CGY750/GY701/GV-1, etc.) is used, the speed can be adjusted from the transmitter. CH7 or CH8 can be selected as the speed setting control channel.

(HELICOPTER) When using a separate ON/OFF switch (cut switch), ON/OFF control uses CH8. In this case, CH7 controls speed setting. Setting examples Example of setting that switches the speed and ON/OFF by 3 position switch Governor speed setting example R.P.M 1OFF R.P.M 21400 R.P.M 31700

*For example, speed 3 sets the maximum speed to be used and is lowered and adjusted at the transmitter. 3position Setup of rate Switch direction UP CNTR DOWN

*For the time being use the initial rate setting. 0%

50%

100%

Adjustment from transmitter 0%Governor R.P.M "o"

"50%"

"100%"

*Since speed adjustment from the transmitter is rate setting, checking the actual speed at the governor display and remembering its relationship is convenient. Switching the speed for each condition The speed for each condition can be set by selecting "Cond" by switch. Since speed adjustment from the transmitter is rate setting, for the actual speed check the governor display. Controlling governor ON/OFF by separate switch When a separate switch is used to turn the governor on and o, switch setting is performed by "OFF-CNTRL"

item.

*Speed and ON/OFF switch settings are different depending on the governor. Perform these settings in accordance with the instruction manual of the governor used.

*At throttle hold, always conrm that the governor is OFF. Conversely, when raising the speed value, reverse the polarity of "CH8". Method Calling the setting screen Call the menu screen from the home screen by pressing the +

key for 1 second. 1 second

"GOVERNOR"

Select from the menu with the Jog key. Open the setting screen by pressing the Jog key. Activating the function Switch selection Setup of rate Select the setting item with the Jog key. GOVERNOR When "INH", the function cannot be used. When you want to use CH7 as the speed setting channel, select "CH7"

and when you want to use CH8(9), select "CH8(9)". Rate The above screen shows the case when the speed is set for each condition. H e l i c o p t e r 141 Switch selection Select the "MODE"

item and then select the switch by pressing the + key or key. or RangeCond, SwA SwH Governor mixing Activating the functionR.P.M CH selection Select the "MIX" item and then select the

"CH7""CH8" or "CH9" by pressing the + key or key. When you do not use a function, set to the or

"INH" side. ting R.P.M set Select the "RATE" item and then adjust the rate by pressing the + key or key. Range0.0 100.0%

or NORM=0.0%, IDL1=50.0%, IDL2=100.0%, Default Cond IDL3=100.0%, HOLD=0.0%

2P Switch selection UP=0.0%, DOWN=100.0%

3P Switch selection UP=0.0%, CNTR=50.0%, DOWN=100.0%

When using an ON/OFF switch

*Select the OFF-CTRL item and then adjust the rate by pressing the + key or key. ON/OFF Switch selection Switch direction Select the "SW"

Select the "POSI" by pressing the + key or key at the ON item and then select the switch direction selection item. by pressing the 2P SWUP, DOWN

+ key or key. 3P SWUP, UP&D, UP&C, CNTR, C&DN, DOWN or or RangeSwA SwH DefaultSwA When number of rotations goes up at the time of Throttlehold

*If the speed is increased at throttle hold, the governor and transmitter operating directions will not coincide. In this case, match the operating directions by reversing the polarity of "CH8". What is a governor A governor is made up of a set of sensors which read the RPM of the helicopter s head, and a control unit that automatically adjusts the throttle setting to maintain a constant head speed regardless of changes in pitch of blades, weather conditions, etc. Governors are extremely popular in competition helicopters due to the consistency provided. How does it help in helicopter setup? The governor eliminates the need to spend large amounts of time setting up throttle curves, as it automatically adjusts the engine s RPM to maintain the desired head speed. H e l i c o p t e r 142 HOV-THR Hovering throttle Function The hovering throttle function trims the throttle near the hovering point. When the hovering throttle knob is turned clockwise, the speed increases and when it is turned counterclockwise, the speed decreases. Rotor speed changes due to changes in the temperature, Method

(HELICOPTER) humidity, and other flying conditions can be trimmed. Adjust for the most stable rotor speed. More precise trimming is possible by using this function together with the hovering pitch function.

Calling the setting screen Call the menu screen from the home screen by pressing the +

key for 1 second. 1 second

"HOV-THR"

Select from the menu with the Jog key. Open the setting screen by pressing the Jog key. HOV-THR Activating the function Trim memory settting VR setting Selection of condition Select the setting item with the Jog key. idle-up1. Hovering Throttle Activating the function Select the "MIX"

i t e m a n d t h e n select the "ON" by pressing the + key or key. When you do not use a function, set to or the "INH" side. When "INH", the function cannot be used. To use the function, switch to "ON". Compensation amount at trim memory Actual compensation amount including the hovering throttle knob The knob operating direction is dierent depending on the polarity. NORMOnly the normal condition operates NORM/IDL1It operates by normal condition and Selection of condition Select the "MODE" item and then select condition by pressing the + key or key. or RangeNORM, NORM/IDL1 DefaultNORM H e l i c o p t e r VR setting Select the "VR" item and then select the

"VR" or "DT" by pressing the + key or key. RangeNULLOFF, +VR, -VR, +DT5, -DT5,

+DT6, -DT6 Default+DT6 Memorizing the hovering throttle adjustment position Memory setting Select the "RATE" item and memorize the current trim position by pressing the Jog key. When the knob is returned to the center after memorization, the trim position returns to its previous position. NOTEIf memorization is repeated at the same position, the value is cumulated. 143 HOV-PIT Hovering pitch Function The hovering pitch function trims the pitch near the hovering point. When the hovering pitch knob is turned clockwise, the pitch gets stronger and when it is turned counterclockwise, the pitch gets weaker. Rotor speed changes due to changes in temperature, humidity, and other flying conditions can be trimmed. Adjust for the most stable rotor rotation. Method

(HELICOPTER) More precise trimming is possible by using this function together with the hovering throttle function.

Calling the setting screen Call the menu screen from the home screen by pressing the +

key for 1 second. 1 second

"HOV-PIT"

Select from the menu with the Jog key. Open the setting screen by pressing the Jog key. Activating the function Trim memory settting VR setting Selection of condition Select the setting item with the Jog key. HOV-PIT NORMOnly the normal condition operates NORM/IDL1It operates by normal condition and idle-up1. When "INH", the function cannot be used. To use the function, switch to "ON". Compensation amount at trim memory Actual compensation amount including the hovering pitch knob The knob operating direction is dierent depending on the polarity Hovering Pitch Activating the function Select the "MIX"

i t e m a n d t h e n select the "ON" by pressing the + key or key. When you do not use a function, set to or the "INH" side. Selection of condition Select the "MODE" item and then select condition by pressing the + key or key. or RangeNORM, NORM/IDL1 DefaultNORM VR setting Select the "VR" item and then select the

"VR" or "DT" by pressing the + key or key. RangeNULLOFF, +VR, -VR, +DT5, -DT5,

+DT6, -DT6 Default-VR or Memorizing the hovering pitch adjustment position Memory setting Select the "RATE" item and memorize the current trim position by pressing the Jog key. When the knob is returned to the center after memorization, the trim position returns to its previous position. NOTEIf memorization is repeated at the same position, the value is cumulated. H e l i c o p t e r 144 HI/LO-PIT HI/LO-pitch trim Function The high/low pitch trim function adjusts the pitch servo high side and low side to the optimum

idle up 1/2/3, hold).

(HELICOPTER)

Method Calling the setting screen Call the menu screen from the home screen by pressing the +

key for 1 second. 1 second

"HI/LO-PIT"

Select from the menu with the Jog key. Open the setting screen by pressing the Jog key. Present condition Actual adjustment position including high pitch trim Selected from among DT5, DT6, and VR. The operation d i r e c t i o n i s d i f f e r e n t depending on the polarity (+,

-). or Adjustment by Key operation Select each function item of "HI-PIT" or "LO-PIT" and set the pitch rate by pressing the + key or key. Range60 100%

Default100%

HI/LO-PIT Selection of condition High side Pitch Trim ON,OFF High side trim Low side same with the Jog key. Select the setting item HI/LO-pitch trim Selection of condition Select the setting condition selection item and select the condition by pressing the + key or key. DT, VR adjustment ON, OFF selection Select ON, OFF by pressing the + key or key at the high side or low side "ADJ"

item. TYP selection Select trim or VR by pressing the + key or key at the "TYP" item. Range+DT5, -DT5, +DT6, -DT6,+VR,

-VR The high side or low side pitch can be adjusted with the selected digital trim or VR. H e l i c o p t e r 145 THR-MIX Throttle mixing Function This mixing compensates for slowing of the helicopter when the ailerons, elevators, and rudder are operated.

(HELICOPTER)

Method Calling the setting screen Call the menu screen from the home screen by pressing the +

key for 1 second. 1 second

"THR-MIX"

Select from the menu with the Jog key. Open the setting screen by pressing the Jog key. THR-MIX Activating the function Condition Mixing Select the setting item with the Jog key. Rate When not using this function, select INH. Present condition Throttle mixing Activating the function Select the "MIX" item and then select the

"ON" by pressing the + key or key. or When you do not use a function, set to the "INH" side. H e l i c o p t e r 146 Setup of rate Select each function item of "MIX" and set the rate by pressing the + key or key. Range0 100%

or RUD THR : -100 +100%

Default0%

When you want to return the set value to the initial value, press the + key and key simultaneously. The setting condition can be selected by pressing the Jog key at rate adjustment. RangeNORM, IDL1, IDL2, IDL3 THR NEEDL Throttle NeedlemixingFor helicopters (HELICOPTER) Function This mixing sets the mixture by a 5 point curve in relation to throttle stick movement when the engine is equipped with a mixture control system (needle control or other mixture adjustment). Normal condition

(NOR) idle up use (ID2) and idle up 3 (ID3) can be set independently. The needle servo connects to CH8 of the transmitter. Method 8CH Calling the setting screen Call the menu screen from the home screen by pressing the +

key for 1 second. 1 second

"THR NEEDL"

Select from the menu with the Jog key. Open the setting screen by pressing the Jog key.

When not using this function, select INH. Present condition Activating the function Condition 5 point curve set Select the setting item with the Jog key. Throttle Needlemixing Activating the function Select the "MIX" item and then select the "ON" or "OFF" by pressing the + key or key. When you do not use a function, set to the "INH" side. or ting 5 point curve set Select the setting item of each point (P-1 P-5) with the Jog key and set the travel of each point by pressing the + key or key. Range0.0 100.0%

or The CURVE settings are displayed by a curve. When such, setting condition can be chosen by pressing Jog key. RangeNOR, I12, ID3 Default P-5: 100.0%

P-4: 75.0%

P-3: 50.0%

P-2: 25.0%

P-1: 0.0%

When you want to return the set value to the initial value, press the + key and key simultaneously. Curve copying method Select the "CND" item and switch to the curve copy mode by pressing the Jog key. Press the + key or key and select the copy destination condition. Copy the condition by pressing the Jog key for 1 second. or 1 second H e l i c o p t e r 147 Glider function The setting screen of each function is called from the following menu. The function when the model type was set to glider (2AIL+4FLP) is displayed here. Power ON First set the throttle to slow. Then turn on the power. Home screen AF4 To menu screen by holding down the + key When the END key is pressed, the display returns to the home screen. END MENU

1

1 MENU MENU 1/3 1/3

12 MENU 2/3

G l i d e r

1 second When the + key is pressed for 1 second, the menu screen is displayed. Selection M o v e t h e c u r s o r

(highlighted) up and down and to the left and right with the Jog key and select the function. The cursor can be moved over several pages.

123 Calling the setting screen MENU 3/3

Press the Jog key to open the setting screen. 148 Key LCD key key AF4 END key Jog key The menu item is an example of WING type 2 ailerons + 4 aps. The menu items can be changed according to the WING type. For example, if WING type is 1AIL, since the item blinks, reference only the item of the WING type used. Relevant WING type display WING TYPE 1AIL 2AIL 2AIL+1F 2AIL+2F 2AIL+4F Refer to "Common Functions"

previously described for a description of this function. Function MENU2/3

(P.66) TELEMETRY TELEMETRY

(P.66) Telemetry Display Alarm setup Telemetry Display Alarm setup

(P.83) SENSOR SENSOR

(P.83) Telemetry sensor Telemetry sensor SBUS LINK SBUS LINK

(P.89)

(P.89) S.BUS servo set up S.BUS servo set up

(P.92) MDL-TRANS MDL-TRANS

(P.92) Data transfer of another 10J or 8J Data transfer of another 10J or 8J TRAINER TRAINER

(P.93)

(P.93) Trainer Trainer AIL-DIFF

(P.150) Aileron Dierential AIL RUD

(P.151) Aileron Rudder

(P.152) V-TAIL V-Tail GYRO SENS

(P.153) Gyro mixing MENU1/3

(P.40) MDL-SEL MDL-SEL

(P.40) Model select Model Copy Data Model select Model Copy Data reset RX Link reset RX Link MDL-NAME

(P.43) MDL-NAME

(P.43) Model name User name Model name User name FAIL SAFE FAIL SAFE

(P.45)

(P.45) Fail safe Fail safe REVERSE

(P.47)

(P.47) REVERSE Servo reverse Servo reverse TIMER TIMER

(P.48)

(P.48) Timer Timer SERVO

(P.49)

(P.49) SERVO Servo monitor Servo test Servo monitor Servo test END POINT END POINT

(P.50)

(P.50) End point End point TRIM

(P.51)

(P.51) TRIM Trim reset Trim step Trim reset Trim step SUB TRIM SUB TRIM

(P.52)

(P.52) Sub trim Sub trim P.MIX1-6

(P.53)

(P.53) P.MIX1-6 Program mixing 1 6 Program mixing 1 6 AUX-CHAN AUX-CHAN

(P.56)

(P.56) AUX channel AUX channel PARAMETER

(P.58)

(P.58) PARAMETER Data reset Model type ATL-

Data reset Model type ATL-

trim LCD contrast Back light :

trim LCD contrast Back light :

mode, time, adjustment Home mode, time, adjustment Home display Battery alarm Battery display Battery alarm Battery vibration Buzzer tone Jog vibration Buzzer tone Jog navi Jog light Jog time navi Jog light Jog time Telemetry : mode, unit Speech :

Telemetry : mode, unit Speech :

language, volume Stick position language, volume Stick position alarm alarm MENU 3/3 D/R, EXPO Dual rate EXPO MOTOR SW Motor switch CONDITION Condition RUD AIL Rudder Aileron mixing CAMBR FLP Camber ap mixing CAMBR MIX Camber mixing BUTTERFLY Buttery mixing CAMBR ELE Camber Elevator mixing ELE CAMBR Elevator Camber mixing AIL CAMBR Aileron Camber mixing AIL BRKFL Aileron Brake ap TRIM MIX Trim MIX

(P.154)

(P.156)

(P.157)

(P.158)

(P.159)

(P.160)

(P.161)

(P.162)

(P.163)

(P.165)

(P.166)

(P.167) G l i d e r 149 AIL-DIFF Aileron dierential Function Two servos can be used for ailerons and a differential can be applied to left and right WING TYPE aileron operation. Connect the left aileron to CH1 (AIL) and the right aileron to CH7.

(GLIDER) 1AIL 2AIL 2AIL+1F 2AIL+2F 2AIL+4F CH1 CH7 Method Calling the setting screen Call the menu screen from the home screen by pressing the +

key for 1 second. 1 second

"AIL-DIFF"

Select from the menu with the Jog key. Open the setting screen by pressing the Jog key. Aileron rate LAileron Stick Left side rate RAileron Stick Right side rate AIL-DIFF Aileron1CH1rate Aileron2CH7rate Select the setting item with the Jog key. Aileron Dierential Aileron control surface angle adjustment Select the "RATE-AIL1" item and then move the aileron stick to the left and right and adjust the travel of each by pressing the + key or key. Range-120 +120%

Default+100%

When you want to return the set value to the initial value, press the + key and key simultaneously.However, polarity does not return. Adjust the RATE-AIL2 item the same as . G l i d e r 150

(GLIDER) 1AIL 2AIL 2AIL+1F 2AIL+2F 2AIL+4F AIL RUD Aileron Rudder Function WING TYPE Use this mix when you want to mix the rudder with aileron operation. This allows the aircraft to bank at a steep angle.

Method Calling the setting screen Call the menu screen from the home screen by pressing the +

key for 1 second. 1 second

"AIL RUD"

Select from the menu with the Jog key. Open the setting screen by pressing the Jog key. Activating the function Rate adjustment

INH Select the setting item with the Jog key.

3 Position Switch NULL ON ON OFF ON OFF ON 2 Position Switch NULL ON ON ON OFF UP UP UP&DWN UP&CNT ON OFF ON ON ON OFF CENTER OFF ON OFF CNT&DN OFF ON ON DOWN OFF OFF ON DOWN OFF ON When not using this function, select INH. When condition was used, the display can be switched and each connection can be set by switching the condition switch. The ON/OFF switch can be changed.

(Selected with the Jog key and changed with the +key) Sets the ON/OFF direction of the selected switch. Aileron Rudder Activating the function Select the "MIX" item and then select the "ON" by pressing the + key or key. or Mixing rate Select the "RATE" item and then adjust the mixing rate by pressing the + key or key. or G l i d e r Range-100 +100%

Default0%

When you do not use a function, set to the "INH" side. When you want to return the set value to the initial value, press the + key and key simultaneously.However, polarity does not return. 151 V-Tail V-TAIL Function This mixing is used with V tail aircraft that combine the elevator and rudder functions. WING TYPE

(GLIDER) 1AIL 2AIL 2AIL+1F 2AIL+2F 2AIL+4F

-tail CH2 (CH4) Elevator Rudder CH2 Servo ELE1 RUD2 CH4 (CH2) CH4 Servo ELE2 RUD1

"V-TAIL"

Select from the menu with the Jog key. Open the setting screen by pressing the Jog key. V-TAIL When INH is selected, the function cannot be used. To use the function, select ACT. Rate adjustment Method Calling the setting screen Call the menu screen from the home screen by pressing the +

key for 1 second. 1 second Activating the function ELE1 rate ELE2 rate RUD2 rate RUD1 rate Select the setting item with the Jog key. V-TAIL Activating the function Select the "MIX" item and then select the "ACT" by pressing the + key or key. or When you do not use a function, set to the "INH" side. Rate adjustment Select the "RATE" item and then adjust the mixing rate by pressing the + key or key. Range-100 +100%

only ELE2 : -50%

Default+50%

or When you want to return the set value to the initial value, press the + key and key simultaneously.However, polarity does not return. NOTEWe recommend that setting be performed while moving the stick and checking the amount of movement. If the amount of movement is too large, elevator and rudder operation will be compounded and the servo travel range will be exceeded and a dead band in which the servo will not operate may be created. G l i d e r 152 GYRO SENS Gyro sensor Function This function is dedicated mixing for switching the gyro sensitivity and gyro mode (AVCS/

NORMAL) of Futaba airplane use gyros. Up to 3 axes can be set.

Method WING TYPE

(GLIDER) 1AIL 2AIL 2AIL+1F 2AIL+2F 2AIL+4F

Calling the setting screen Call the menu screen from the home screen by pressing the +

key for 1 second. 1 second

"GYRO SENS"

Select from the menu with the Jog key. Open the setting screen by pressing the Jog key. GYRO SENS Activating the function Gain Channel selection Switch direction Gyrotype, Gain rate When not using this function, select INH. Sensitivity switch selection Current switch operating direction Switches to the sensitivity setting screen of each switch direction when the Jog key is pressed. Select the setting item with the Jog key. GYRO SENS Gyro type Gyro Gain When using a Futaba GYA gyro, select gyro type GY. This switches the gyro sensitivity setting item to mode and sensitivity direct reading display. Activating the function Select the "MIX" item and then select the

"ON" by pressing the +

key or key. When you do not use a function, set to the or

"INH" side. Sensitivity switch selection Select the "SW" item and then select the switch by pressing the + key or key. or RangeSwA SwHDefaultSwA Sensitivity setting channel selection S e l e c t t h e

"CH" item and t h e n s e l e c t the sensitivity setting channel by pressing the + key or key. or RangeCH5CH5/CH7 CH5/CH8CH5/CH7/CH8 DefaultCH5 Gyro type and sensitivity setting Press the Jog key and select the sensitivity setting screen you want to set and then set "type" (gyro type) and "rate" (gyro sensitivity) of each channel by pressing the + key or key.

"type"RangeSTD,GYDefaultSTD

"rate"Range0 100%STD, NOR100 0 AVC100%GYDefault50%STD, 0%GY When you want to return the set value to the initial value, press the + key and key simultaneously. G l i d e r 153 D/R,EXPO Dual rate EXPO Function WING TYPE

(GLIDER) 1AIL 2AIL 2AIL+1F 2AIL+2F 2AIL+4F D/R The aileron, elevator and rudder channel control surface angle can be switched in 2 steps

EXP This function makes operation more pleasant by changing the operating curve so that servo movement is sluggish or sensitive relative to stick operation near the aileron, elevator, throttle, and rudder neutral position. Adjustments can be made in 2 steps according to the control surface angle.

Switch selectionSW Switches A to H can be selected as the aileron channel, elevator channel, and rudder channel dual rate

(exponential) switch.

Method Calling the setting screen Call the menu screen from the home screen by pressing the +

key for 1 second. 1 second

"D/R, EXPO"

Select from the menu with the Jog key. Open the setting screen by pressing the Jog key. G l i d e r Channel selection Dual rate EXPO Switch selection Channel selection/Select the setting item with the Jog key. 154 The channel under selection is underlined. Switch Direction The dual rate and exponential settings are displayed by a curve. Channel 1Aileron 2Elevator 3Throttle 4Rudder Switch number D/R and EXPO rate display Top rowLeft side down Bottom rowRight side up D/R A channel is chosen by Jog key. Range1, 2, 4 Adjust the rate by moving the cursor to D/R with the Jog key, switching the dual rate switch to the direction you want to set, moving the stick to the left

(down) or right (up) side and pressing the + key or key. Range 0 140%

Default100%

When you want to return the set value to the initial value, press the + key and key simultaneously. Adjust the rate of each direction of the dual rate switch and stick by repeating step EXPO Select the "EXP" item and then select the channel with the Jog key. Range1 4 Moving to another setting item of the same channel is possible by Jog key. Adjust the rate by moving the cursor to EXP with the Jog key, switching the dual rate switch to the direction you want to set, moving the stick to the left

(down) or right (up) side and pressing the + key or key. Range

-100 +100%

Default0%

When you want to return the set value to the initial value, press the + key and key simultaneously. Adjust the rate of each direction of the dual rate switch and stick by repeating step Moving to another setting item of the same channel is possible by Jog key. Switch Change Select the "SW" item and then select the channel with the Jog key. Range1, 2, 4 A switch is chosen by + key or key. or RangeSwA SwH G l i d e r 155 MOTOR SW Motor switch Function This function sets the operating motor when the EP glider with motor is started by switch. The operating speed can individually set in 2 ranges of high from slow and slow from high. If you do motor control with a throttle stick, you should set this function to INH. Method WING TYPE

(GLIDER) 1AIL 2AIL 2AIL+1F 2AIL+2F 2AIL+4F

Calling the setting screen Call the menu screen from the home screen by pressing the +

key for 1 second. 1 second

"MOTOR SW"

Select from the menu with the Jog key. Open the setting screen by pressing the Jog key. MOTOR SW

OFF ( 0%)

(OFF) (ON)

Present motor control position If this safety switch is not ON, the motor will not start even if the starter switch is turned on. In

"NULL", a safe function does not work. Start SW A setup of the motor control position (3CH end point)of High-

side and Low-side Decelerating speed setting Accelerating speed setting Select the setting item with the Jog key. Motor Activating the function Select the "MODE" item and then select the

"OFF" by pressing the

+ key or key. When you do not use a function, set to the or

"INH" side. Switch selection Change the switch by pressing the + key or key at the switch selection item. or RangeSwA SwH Switch direction S e l e c t t h e

"DOWN" item and then select the position by pressing the + key or key. 2P SW UP, DOWN 3P SW UP, UP&D, UP&C, CNTR, or C&DN, DOWN Speed setting Select "SPEED " next to (OFF) and (ON) by Jog key. RangeOFF,1 10(more slowly)

(ON) is the acceleration speed setting.

(OFF) is the deceleration speed setting. DANGER Always remove the propeller from the motor during setting and at operation checks.

G l i d e r 156 CONDITION Condition Function The condition function lets you change multiple settings by one switch operation. Different settings can be made immediately by switching 2 conditions. WING TYPE

(GLIDER) 1AIL 2AIL 2AIL+1F 2AIL+2F 2AIL+4F

Method Calling the setting screen Call the menu screen from the home screen by pressing the +

key for 1 second. 1 second

"CONDITION"

Select from the menu with the Jog key. Open the setting screen by pressing the Jog key. Condition1 Condition2 Select the setting item with the Jog key. CONDITION

INH

Activating the function Switch direction Switch selection When not using this Function select INH. The display of On/Off is shown when active and assigned to a switch. Priority is given to the c o n d i t i o n 2 w h e n t h e condition 1 and 2 is turned on simultaneously. CONDITION Activating the function Select the "INH" item of the condition you want to use and then set that condition to "ON" or

"OFF" by pressing the + key or key. Set conditions you do not want to use to "INH". or Changing the switch Switch selection Change the switch by pressing the + key or key at the switch selection item. or RangeSwA SwH DefaultSwA Switch direction Select the ON direction by pressing the + key or key at the ON direction selection item. or Range 2P SWNULL, UP, DOWN 3P SWNULL, UP, UP&D, UP&C, CNTR, C&DN, DOWN G l i d e r 157 RUD AIL Rudder Aileron Function This function is used when you want to mix the ailerons with rudder input. It is used when rudder is applied during roll maneuvers such as, knife edge flight. It can be used to turn or bank scale models, large models, etc. like a full-

size aircraft. Method WING TYPE

(GLIDER) 1AIL 2AIL 2AIL+1F 2AIL+2F 2AIL+4F

Calling the setting screen Call the menu screen from the home screen by pressing the +

key for 1 second. 1 second

"RUD AIL"

Select from the menu with the Jog key. Open the setting screen by pressing the Jog key. Activating the function Mixing rate

Select the setting item with the Jog key.

3 Position Switch NULL ON ON OFF ON OFF ON 2 Position Switch NULL ON ON ON OFF UP UP UP&DWN UP&CNT ON OFF ON ON ON OFF CENTER OFF ON OFF CNT&DN OFF ON ON DOWN OFF OFF ON DOWN OFF ON When not using this function, select INH. When condition was used, the display can be switched and each connection can be set by switching the condition switch. The ON/OFF switch can be changed.

(Selected by Jog key and changed by

+ key.) Sets the ON/OFF direction of the selected switch. G l i d e r RUD AIL Activating the function Select the "MIX" item and then select the "ON" by pressing the + key or key. or Mixing rate Select the "RATE" item and then adjust the mixing rate by pressing the + key or key. or Range-100 +100%

Default0%

When you do not use a function, set to the "INH" side. When you want to return the set value to the initial value, press the + key and key simultaneously.However, polarity does not return. 158 CAMBR FLP Camber ap Function

(GLIDER) 1AIL 2AIL 2AIL+1F 2AIL+2F 2AIL+4F WING TYPE

independently for each servo according to the

Aileron1

(CH1) Flap1

(Camber Flap)

(CH5) Flap3

(Brake Flap)

(CH8) Flap4

(Brake Flap)

(CH9) Flap2

(Camber Flap)

(CH6) Aileron2

(CH7) Method Calling the setting screen Call the menu screen from the home screen by pressing the +

key for 1 second. 1 second

"CAMBR FLP"

Select from the menu with the Jog key. Open the setting screen by pressing the Jog key. DT5 and DT6 set t h e a m o u n t o f movement when the ap is operated.

1

Flap1 Flap2 Flap3 Flap4

+100

Up side rate Down side rate Oset rate Select the setting item with the Jog key. The number is changed by + key or key. Camber FLP page

[Brakeap Camberap] Currently selected condition

12

+100

Brake FLP to camber FLP mixing rate and offset

(axis shift) Brake FLP to camber FLP mixing switch selection Brake FLP to camber FLP mixing switch operation direction Selection of whether or not mixing from brake FLP to camber FLP is performed G l i d e r 159 CAMBR MIX Camber mixing Function WING TYPE

(GLIDER) 1AIL 2AIL 2AIL+1F 2AIL+2F 2AIL+4F This function adjusts the rate of camber operation for the wing camber (ailerons, camber flaps, brake flaps) in the negative and positive directions. The aileron, flap, and elevator rates can also be adjusted independently and attitude changes caused by camber operation can be corrected.

All the wing control surfaces are lowered and the camber is increased

(lift increases) Turn the VR All the wing control surfaces are raised and the camber is decreased (lift decreases) Attitude changes are compen-

sated for by setting the amount of elevator movement. Method Calling the setting screen Call the menu screen from the home screen by pressing the +

key for 1 second. 1 second Attitude changes are compen-

sated for by setting the amount of elevator movement.

"CAMBR MIX"

Select from the menu with the Jog key. Open the setting screen by pressing the Jog key. Sets the amount of movement when the VR was turned. Aileron1 Aileron2 Camber MIX ACT/INH Can be set to operate from a switch. When NULL, it is operated by a VR. Currently selected condition

1 2

0

Select the setting item with the Jog key. The number is changed by + key or key.

(RATE1)T h e a m o u n t o f operations when VR is turned to the right.

(RATE2)T h e a m o u n t o f operations when VR is turned to the left. Sets the amount of movement when the VR is turned. Flap1 Flap2 Flap3 Flap4 Elevator

[Camber FLP page]

Currently selected condition

1 2

0

Amount of compensation of the elevator when the camber changed. G l i d e r 160 BUTTERFLY Buttery mixing Function WING TYPE This function is utilized to quickly slow the aircraft and reduce altitude by simultaneously raising the left and right ailerons and lowering the

Butterfly (Crow) produces an extremely

OFF ON Switch set to ON THR stick lowered

(GLIDER) 1AIL 2AIL 2AIL+1F 2AIL+2F 2AIL+4F

Resistance increased by raising the elevators and lowering the aps Fine tuning of an elevator Method Calling the setting screen Call the menu screen from the home screen by pressing the +

key for 1 second. 1 second

"BUTTERFLY"

Select from the menu with the Jog key. Open the setting screen by pressing the Jog key. Amount of movement setting Currently selected condition Aileron1 Aileron2 compensation Amount of elevator Buttery : ACT/INH Can be either set to a switch or when NULL is controlled by the THR stick. Oset setting Select "OFST" XX%.

1

Current THR stick position 0 : High 100 : Low Brake amount MAX OFST 0%

At THR stick high press the Jog key for 1 second High THR stick operation Slow Brake amount MAX OFST 50%

Start from center At THR stick center press the Jog key for 1 second High Slow THR stick operation Select the setting item with the Jog key. The number is changed by + key or key. When MIX is set to ACT, the amount of MIX(s) according to stick operation is displayed. G l i d e r 161 CAMBRELE Camber Elevator mixing Function WING TYPE

(GLIDER) 1AIL 2AIL 2AIL+1F 2AIL+2F 2AIL+4F When the camber/speed flaps are utilized, the aircraft might experience, a change in pitch. This mix compensates for such changes by incorporating elevator input.

Method Calling the setting screen Call the menu screen from the home screen by pressing the +

key for 1 second. 1 second Flap operation pitch change Flap1

(CH5) Elevator

(CH2) Flap2

(CH6) compensated for by elevators

"CAMBR ELE"

Select from the menu with the Jog key. Open the setting screen by pressing the Jog key. Mixing rate Activating the function Select the setting item with the Jog key.

0

When not using this function, select INH. When condition is used, the display can be switched and each connection can be set by switching the condition switch. 3 Position Switch NULL ON ON OFF ON OFF ON 2 Position Switch NULL ON ON ON OFF UP UP UP&DWN UP&CNT ON OFF ON ON ON OFF CENTER OFF ON OFF CNT&DN OFF ON ON DOWN OFF OFF ON DOWN OFF ON The ON/OFF switch can be changed.

(Selected with the Jog key and changed with the +key) Sets the ON/OFF direction of the selected switch.

(RATE1) and (RATE2) show the direction of camber of operation. Camber ELE mixing Activating the function Select the "MIX" item and then select the "ON" by pressing the + key or key. or When you do not use a function, set to the "INH" side. Mixing rate Select the "RATE" item and then adjust the mixing rate by pressing the + key or key. or Range-120 +120%

Default0%

When you want to return the set value to the initial value, press the + key and key simultaneously. G l i d e r 162 ELE CAMBR Elevator Camber mixing Function WING TYPE

(GLIDER) 1AIL 2AIL 2AIL+1F 2AIL+2F 2AIL+4F This function is used when you want to mix the

the flaps are lowered by up elevator, and lift is increased.

Up the elevator Aileron1

(CH1) Flap1

(Camber Flap)

(CH5) Flap3

(Brake Flap)

(CH8) Flap4

(Brake Flap)

(CH9) Flap2

(Camber Flap)

(CH6) Aileron2

(CH7) Elevator

(CH2)

"ELECAMBR"

Select from the menu with the Jog key. Open the setting screen by pressing the Jog key. ap is down Method Calling the setting screen Call the menu screen from the home screen by pressing the +

key for 1 second. 1 second Mixing rate

12 Currently selected condition Aileron1 Aileron2 Camber MIX ACT/INH Can be either set to a switch or when NULL is always active.

0

Described on the next page. Current position of the elevator stick Select the setting item with the Jog key. The number is changed by + key or key.

[ELE Camber page]

Currently selected condition Mixing rate Flap1 Flap2 Flap3 Flap4

(RATE1) and (RATE2) show the direction of elevator of operation. G l i d e r 163 ELE Camber

12

When MIX is set to ACT, the amount of MIX(s) according to stick operation is displayed. Setting that inhibits camber mixing near the elevator center position. Setting so that camber mixing is performed only when the elevators were operated greatly is possible. RANGE setting Setting state Select the "0%" item next to RANGE with the Jog key. To setting value Move the elevator stick to the position you want operation to begin. Set value memorization Press the Jog key for 1 second. Hold the stick in position. Can be either up or down. When set to down, the up side is also set by the same amount.

12

When elevator operation exceeds the range, the stick position is displayed and mixing is performed. When a RANGE number is selected and the Jog key is pressed for 1 second, RANGE is reset to 0% and normal mixing is performed. G l i d e r 164 AIL CAMBR Aileron Camber mixing Function

operation (stick). It is used when you want to increase roll axis maneuverability. WING TYPE

(GLIDER) 1AIL 2AIL 2AIL+1F 2AIL+2F 2AIL+4F

OFF ON Set switch to ON Flaps and ailerons operate Ailerons operation Roll is corrected by using the ailerons to control the camber FLP. Method Calling the setting screen Call the menu screen from the home screen by pressing the +

key for 1 second. 1 second

"AIL CAMBR"

Select from the menu with the Jog key. Open the setting screen by pressing the Jog key. Mixing rate Activating the function Select the setting item with the Jog key.

0

When not using this function, select INH. When condition was used, the display can be switched and each connection can be set by switching the condition switch. 3 Position Switch NULL ON ON OFF ON OFF ON 2 Position Switch NULL ON ON ON OFF UP UP UP&DWN UP&CNT ON OFF ON ON ON OFF CENTER OFF ON OFF CNT&DN OFF ON ON DOWN OFF OFF ON DOWN OFF ON The ON/OFF switch can be changed.

(Selected with the Jog key and changed with the +key) Sets the ON/OFF direction of the selected switch. AIL Camber mixing Activating the function Select the "MIX" item and then select the "ON" by pressing the + key or key. or When you do not use a function, set to the "INH" side. Mixing rate Select the "RATE" item and then adjust the mixing rate by pressing the + key or key. or Range-120 +120%

Default0%

When you want to return the set value to the initial value, press the + key and key simultaneously. G l i d e r 165 AIL BRKFL Aileron Brake ap mixing Function This mixing links the brake flaps with aileron operation (stick). It is used when you want to increase roll axis maneuverability. WING TYPE

(GLIDER) 1AIL 2AIL 2AIL+1F 2AIL+2F 2AIL+4F

OFF ON Set the switch to ON Ailerons operation Flaps and ailerons operate Roll is corrected by using the ailerons to control the brake FLP. Method Calling the setting screen Call the menu screen from the home screen by pressing the +

key for 1 second. 1 second

"AILBRKFL"

Select from the menu with the Jog key. Open the setting screen by pressing the Jog key. Mixing rate Activating the function Select the setting item with the Jog key.

0

When not using this function, select INH. When condition was used, the display can be switched and each connection can be set by switching the condition switch. 3 Position Switch NULL ON ON OFF ON OFF ON 2 Position Switch NULL ON ON ON OFF UP UP UP&DWN UP&CNT ON OFF ON ON ON OFF CENTER OFF ON OFF CNT&DN OFF ON ON DOWN OFF OFF ON DOWN OFF ON The ON/OFF switch can be changed.

(Selected with the Jog key and changed with the +key) Sets the ON/OFF direction of the selected switch. AIL BRKFL mixing Activating the function Select the "MIX" item and then select the "ON" by pressing the + key or key. or When you do not use a function, set to the "INH" side. Mixing rate Select the "RATE" item and then adjust the mixing rate by pressing the + key or key. or Range-120 +120%

Default0%

When you want to return the set value to the initial value, press the + key and key simultaneously. G l i d e r 166 TRIM MIX Trim mix Function This function shifts the ailerons, elevators, and

switch. WING TYPE

(GLIDER) 1AIL 2AIL 2AIL+1F 2AIL+2F 2AIL+4F

OFF ON Set the switch to ON Aileron1

(CH1) Flap1

(Camber Flap)

(CH5) Flap3

(Brake Flap)

(CH8) Flap4

(Brake Flap)

(CH9) Flap2

(Camber Flap)

(CH6) Aileron2

(CH7) Method Calling the setting screen Call the menu screen from the home screen by pressing the +

key for 1 second. 1 second Trim of each control surface is moved to the set value. Elevator

(CH2)

"TRIM MIX"

Select from the menu with the Jog key. Open the setting screen by pressing the Jog key.

[TRIM MIX page1]

TRIM MIX (NORM) 1 2

0

0

0

0

0

0

0 Select the setting item with the Jog key. The number is changed by + key or key.

[TRIM MIX page2]

TRIM MIX 1 2 Activating the function When not using this function, select INH.

INH

3 Position Switch NULL ON ON OFF ON OFF ON 2 Position Switch NULL ON ON ON OFF UP UP UP&DWN UP&CNT ON OFF ON ON ON OFF CENTER OFF ON OFF CNT&DN OFF ON ON DOWN OFF OFF ON DOWN OFF ON When condition is used, the display can be switched and each connection can be set by switching the condition switch. Sets the trim neutral position of each control surface. Range-100 +100 Returned to 0 by pressing the + key and key simultaneously. The ON/OFF switch can be changed.

(Selected with the Jog key and changed with the +key) Sets the ON/OFF direction of the selected switch. Servo speed at which the trim position is to the set position. Sudden attitude changes are prevented by turning the switch on. (Selected by Jog key and changed by + key and key.) RangeOFF(fast shift1 10slow shift Returned to OFF by pressing the Jog key for a long time.

*This is not the servo speed when the stick was operated. G l i d e r 167 Multicopter Function The setting screen of each function is called from the following menu. The function when the model type was set to multicopter (MULTI COPT) is displayed here. Power ON First set the throttle to slow. Then turn on the power. Home screen To menu screen by holding down the + key When the END key is pressed, the display returns to the home screen. END MENU MENU MENU 1/2 1/2 MENU 2/2 M u l t i c o p t e r

1

1

12

1 second When the + key is pressed for 1 second, the menu screen is displayed. Selection M o v e t h e c u r s o r

(highlighted) up and down and to the left and right with the Jog key and select the function. The cursor can be moved over several pages. Calling the setting screen Press the Jog key to open the setting screen. 168 key LCD key key END key Jog key Refer to "Common Functions"

previously described for a description of this function. Function MENU2/3 TELEMETRY

(P.66) TELEMETRY

(P.66) Telemetry Display Alarm setup Telemetry Display Alarm setup

(P.83) SENSOR SENSOR

(P.83) Telemetry sensor Telemetry sensor SBUS LINK

(P.89) SBUS LINK

(P.89) S.BUS servo set up S.BUS servo set up MDL-TRANS MDL-TRANS

(P.92)

(P.92) Data transfer of another T10J Data transfer of another T10J TRAINER

(P.93)

(P.93) TRAINER Trainer Trainer GYRO SENS

(P.170) Gyro mixing

(P.171) D/R, EXPO Dual rate EXPO CNTR ALRM

(P.173) Center alarm MENU1/3 MDL-SEL

(P.40) MDL-SEL

(P.40) Model select Model Copy Data Model select Model Copy Data reset RX Link reset RX Link

(P.43) MDL-NAME MDL-NAME

(P.43) Model name User name Model name User name FAIL SAFE FAIL SAFE

(P.45)

(P.45) Fail safe Fail safe

(P.47) REVERSE REVERSE

(P.47) Servo reverse Servo reverse TIMER TIMER

(P.48)

(P.48) Timer Timer

(P.49) SERVO SERVO

(P.49) Servo monitor Servo test Servo monitor Servo test END POINT END POINT

(P.50)

(P.50) End point End point

(P.51) TRIM TRIM

(P.51) Trim reset Trim step Trim reset Trim step SUB TRIM SUB TRIM

(P.52)

(P.52) Sub trim Sub trim

(P.53) P.MIX1-6 P.MIX1-6

(P.53) Program mixing 1 6 Program mixing 1 6 AUX-CHAN AUX-CHAN

(P.56)

(P.56) AUX channel AUX channel PARAMETER

(P.58) PARAMETER

(P.58) Data reset Model type ATL-

Data reset Model type ATL-

trim LCD contrast Back light :

trim LCD contrast Back light :

mode, time, adjustment Home mode, time, adjustment Home display Battery alarm Battery display Battery alarm Battery vibration Buzzer tone Jog vibration Buzzer tone Jog navi Jog light Jog time navi Jog light Jog time Telemetry : mode, unit Speech :

Telemetry : mode, unit Speech :

language, volume Stick position language, volume Stick position alarm alarm M u l t i c o p t e r 169 GYRO SENS Gyro sensor Function This function is dedicated mixing for switching the gyro sensitivity and gyro mode (AVCS/

NORMAL) of Futaba gyros. Up to 3 axes can be set. The attitude control of multicopter uses the system of multicopter attachment. This "GYROSENS" will be used for accessories, such as camera control. Method

(MULTICOPT)

*When this function is used, it becomes impossible for CH5 to use it for multi copter controller. Use CH6 for multi copter controller and use SwC. Calling the setting screen Call the menu screen from the home screen by pressing the +

key for 1 second. 1 second

"GYRO SENS"

Select from the menu with the Jog key. Open the setting screen by pressing the Jog key. Activating the function Gain Channel selection Switch direction Gyrotype, Gain rate Select the setting item with the Jog key. GYRO SENS Gyro type Gyro Gain When not using this function, select INH. Gain switch selection Current switch operating direction S w i t c h e s t o t h e sensitivity setting screen of each switch direction when the Jog key is pressed. When using a Futaba GYA gyro, select gyro type GY. This switches the gyro sensitivity setting item to mode and sensitivity direct reading display. GYRO SENS Activating the function Select the "MIX" item and then select the

"ON" by pressing the +

key or key. When you do not use a function, set to the or

"INH" side. Sensitivity switch selection Select the "SW" item and then select the switch by pressing the + key or key. or RangeSwA SwHDefaultSwA Sensitivity setting channel selection S e l e c t t h e

"CH" item and t h e n s e l e c t the sensitivity setting channel by pressing the + key or key. or RangeCH5CH5/CH7 CH5/CH8CH5/CH7/CH8 DefaultCH5 Gyro type and sensitivity setting Press the Jog key and select the sensitivity setting screen you want to set and then set type (gyro type) and rate (gyro sensitivity) of each channel by pressing the +key or key.

"type"RangeSTD,GYDefaultSTD

"rate"Range0 100%STD, NOR100 0 AVC100%GYDefault50%STD, 0%GY When you want to return the set value to the initial value, press the + key and key simultaneously. M u l t i c o p t e r 170 D/R,EXPO Dual rate EXPO Function

(MULTICOPT) D/R The aileron, elevator and rudder channel control surface angle can be switched in 2 steps

EXP This function makes operation more pleasant by changing the operating curve so that servo movement is sluggish or sensitive relative to stick operation near the aileron, elevator, throttle, and rudder neutral position. Adjustments can be made in 2 steps according to the control surface angle.

Switch selectionSW Switches A to H can be selected as the aileron channel, elevator channel, and rudder channel dual rate

(exponential) switch.

Method Calling the setting screen Call the menu screen from the home screen by pressing the +

key for 1 second. 1 second

"D/R,EXPO"

Select from the menu with the Jog key. Open the setting screen by pressing the Jog key. Channel selection Dual rate EXPO Switch selection Channel selection/Select the setting item with the Jog key. The channel under selection is underlined. Switch Direction The dual rate and exponential settings are displayed by a curve. Switch number D/R and EXPO rate display Top rowLeft side down Bottom rowRight side up Channel 1Aileron 2Elevator 3Throttle 4Rudder M u l t i c o p t e r 171 D/R A channel is chosen by Jog key. Range1, 2, 4 Adjust the rate by moving the cursor to D/R with the Jog key, switching the dual rate switch to the direction you want to set, moving the stick to the left

(down) or right (up) side and pressing the + key or key. Range 0 140%

Default100%

When you want to return the set value to the initial value, press the + key and key simultaneously. Adjust the rate of each direction of the dual rate switch and stick by repeating step EXPO Select the "EXP" item and then select the channel with the Jog key. Range1 4 Moving to another setting item of the same channel is possible by Jog key. Adjust the rate by moving the cursor to EXP with the Jog key, switching the dual rate switch to the direction you want to set, moving the stick to the left

(down) or right (up) side and pressing the + key or key. Range

-100 +100%

Default0%

When you want to return the set value to the initial value, press the + key and key simultaneously. Adjust the rate of each direction of the dual rate switch and stick by repeating step Moving to another setting item of the same channel is possible by Jog key. Switch Change Select the "SW" item and then select the channel with the Jog key. Range1, 2, 4 A switch is chosen by + key or -key. or RangeSwA SwH M u l t i c o p t e r 172 CNTR ALRM Center alarm Function

(MULTICOPT) Beep sounds When the THR stick is set to the specied position.

"CNTR ALRM"

Select from the menu with the Jog key. Open the setting screen by pressing the Jog key. Method Calling the setting screen Call the menu screen from the home screen by pressing the +

key for 1 second. 1 second Select the item with the Jog key. INH ON/OFF Switch selsction Switch direction Stick position CNTR ALRM STK POSI ALRM

ON

When INH is selected, the function cannot be used. When ON or OFF is selected, the function is activated. ON and OFF changes are linked to the switch. The number in parenthesis is the current throttle stick position. Position setting Stick position is chosen by Jog key. Set the throttle stick to the position at which you want to generate the alarm. When the Jog key is held down the alarm sounds at that position. CNTR ALRM STK POSI ALRM

ON

45% ( 45%) THR Stick Memorize the position at which the beep is to sound. M u l t i c o p t e r 173 TX SETTING The settings here are special settings that are unnecessary during normal use. The stick mode can be changed and stick adjustment (calibration), throttle lever reverse, and language can be set. Turn on the power switch with the + key and key pressed in the power o state. The screen shown at the left appears. To return to the home screen, turn off the power and then turn the power back on without pressing the keys. This is the MODE1 MODE4 setting. The initial state is MODE2. To change the mode the stick ratchet must be changed. Request that this be done by Futaba Service. (Charged modication) TX SETTING STK-MODE 1 STK-ADJ THR-REV NEXT NOR LANGUAGE English STK-MODE RUD AIL RUD AIL THR ELE MODE 1 ELE THR MODE 2 AIL RUD AIL RUD ELE THR MODE 3 STK-ADJ ELE THR MODE 4 This function is normally not used. If stick deviation should occur, make this adjustment. Do not use it in the normal state. Calling the setting screen Select STK-ADJ NEXT in the menu with the Jog key. Enter the setting screen by pressing the Jog key. Press the Jog key down and select NEUT . Set the stick to the neutral position and press the Jog key. Turn off the power and then turn the power back on while pressing the + key and key simultaneously. Stick adjustment Select the stick you want to adjust with 1 4 with the +

key. 4 1 3 2 174 Swing the selected stick fully to the left and right (up and down). appears next to "LEFT"

and "RGHT". Press the Jog key. When "COMPLETE" is displayed, adjustment is complete. END THR-REV This function is not used. When you want to use full throttle with the throttle stick down and slow with the throttle stick up, select REV. When the stick is up, trim is eective and when the stick is down, trim is not eective.

*Throttle servo operation reversed by the linkage is usually performed by reverse in the normal menu. When throttle servo operation is reversed with the THR-REV function, trim becomes ineective at slow. THR-REV Turn off the power and then turn on the power while pressing the + key and key simultaneously. Select THR-REV NOR in the menu with the Jog key. Select NOR or REV by pressing the + key or key. Setting is ended by power o. LANGUAGE The language displayed at proportional can be changed. The initial setting is Japanese, but can be selected from among 7 languages. LANGUAGE Turn off the power and then turn on the power while pressing the + key and key simultaneously. Select LANGUAGE English in the menu with the Jog key. Select NOR or REV by pressing the + key or key. Setting is ended by power o. Return from the transmitter setting screen to the normal menu by turning on the power without pressing a key. FUTABA CORPORATION 1080 Yabutsuka, Chosei-mura, Chosei-gun, Chiba-ken, 299-4395, Japan Phone: +81 475 32 6982, Facsimile: +81 475 32 6983 2014, 01 (1) 175