FCC ID: AZPT2POK-24G Radio Control

Thank you for purchasing a Futaba FHSS 3PRKA 2.4GHz system. This system is based on the combination of the newly developed 2.4GHz transmitter and its correspondent receiver. Before using your 3PRKA 2.4GHz system, read this manual carefully and use your R/C set safely. After reading this manual, store it in a safe place. FHSS 3PRKA 2.4GHz system 2.4GHzSS (Spread Spectrum) radio communication system Frequency channel setting unnecessary: Sifting the channels within the 2.4GHz band automatically, this system minimizes the interference from other 2.4GHz system. Accepts no unwanted signals by using ID code Built-in antenna (T3PRKA-2.4G transmitter) Application, Export, and Modification 1. This product may be used for models only. It is not intended for use in any application other than the control of models for hobby and recreational purposes. 2. Exportation precautions:

(a) When this product is exported from the country of manufacture, its use is to be approved by the laws governing the country of destination which govern devices that emit radio frequencies. If this product is then re-exported to other countries, it may be subject to restrictions on such export. Prior approval of the appropriate goverment authorities may be required. If you have purchased this product from an exporter outside your country, and not the authorized Futaba distributor in your country, please contact the seller immediately to determine if such export regulations have been met.

(b) Use of this product with other than models may be restricted by Export and Trade Control Regulations, and an application for export approval must be submitted. 3. Modification, adjustment, and replacement of parts: Futaba is not responsible for unauthorized modification, adjustment, and replacement of parts on this product. Any such changes may void the warranty. Compliance Information Statement (for U.S.A.) This device, trade name Futaba Corporation of America, model number R203GF, complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause undesired operation.

*This module meets the requirements for a mobile device that may be used at separation distances of more than 20cm from the human body. To meet the RF exposure requirements of the FCC this device shall not be co-located with another transmitting device. The responsible party of this device compliance is;

3002 N Apollo Drive Suite 1, Champaign, IL 61822 U.S.A. TEL (217)398-8970 or E-mail: support@futaba-rc.com (Support) TEL (217)398-0007 or E-mail: service@futaba-rc.com (Service) Battery Recycling (for U.S.A.) The RBRCTM SEAL on the (easily removable) nickel-cadmium battery contained in Futaba products indicates that Futaba Corporation of America is voluntarily participating in an industry program to collect and recycle these batteries at the end of their useful lives, when taken out of service within the United States. The RBRCTM program provides a convenient alternative to placing used nickel-cadmium batteries into the trash or municipal waste system, which is illegal in some areas. You may contact your local recycling center for information on where to return the spent battery. Please call 1-800-8-BATTERY for information on Ni-Cd battery recycling in your area. Futaba Corporation of America's involvement in this program is part of its commitment to protecting our environment and conserving natural resources. RBRCTM is a trademark of the Rechargeable Battery Recycling Corporation. Table of Contens Safety Precautions ............................. 4 Definition of Symbols ............................................................ 4 2.4GHz System Precautions ................................................. 4 Operation Precautions .......................................................... 5 Storage and Disposal Safety Precautions ........................... 6 Other Safety Precautions ...................................................... 7 Before Operation ................................ 8 System Contents .................................................................... 8 Nomenclature / Handling ....................................................... 9 Assembly / Adjustment ..................... 12 Receiver and Servo Connection ......................................... 12 Receiver antenna Installation ............................................. 12 Assembly Precautions ........................................................ 13 How to link transmitter and receiver .................................. 14 How to open front cover ...................................................... 14 Transmitter Set-Up Procedures .......................................... 15 3PRKA-2.4G Functions ..................... 16 Steering Trim ....................................................................... 16 Throttle Trim ........................................................................ 16 Steering Dual Rates (D/R) .................................................. 17 Steering Servo Reversing .................................................. 17 Throttle Servo Reversing ................................................... 17 Throttle End Point Adjustment (EPA-CH2) ........................ 18 CH3 Function ........................................................................ 18 Fail Safe Function (F/S) ....................................................... 18 MC230CR/MC330CR ............................................................ 19 Reference .......................................... 20 Ratings .................................................................................. 20 Troubleshooting ................................................................... 21 Error Displays ...................................................................... 22 When Requesting Repair .................................................... 22 Safety Precautions Before Operation Assembly /

Adjustment 3PRKA-2.4G Functions Reference Warning: This product contains a chemical known to cause cancer and birth defects (or other reproductive harm). No part of this manual may be reproduced in any form without prior permission. The contents of this manual are subject to change without prior notice. This manual has been carefully written. Please write to Futaba if you feel that any corrections or clarifications should be made. Futaba is not responsible for the use of this product. 3 Safety Precautions For your safety as well as that of others, please read this manual thoroughly prior to installation and operation of your digital proportional R/C system. Definition of Symbols The following defines the symbols used in this manual. Explanation of Symbols

 DANGER Procedures which may lead to a dangerous condition and cause death or serious injury to the user if not carried out properly. Procedures which may lead to a dangerous condition or cause death or serious injury to the user if not carried out properly, or procedures where the probability of superficial injury or physical damage is high.

 WARNING

 CAUTION Procedures where the possibility of serious injury to the user is small, but there is a danger of injury, or physical damage, if not carried out properly. Explanation of Graphic Symbols

 Indicates an operation that prompts a warning (including Caution).

 Indicates an operation that must not be performed.

 Indicates an operation that always must be performed. 2.4GHz System Precautions

 WARNING

 Do not cover/hold the built-in antenna part of T3PRKA-2.4G transmitter by your hand during running. Do not put any conductive plate/sticker on the antenna part. Otherwise, the operating range may become shorter.

 Do not perform the linking procedure with motor's main wire is connected or the engine is operating as it may result in serious injury.

 While the linking is done, please cycle receiver power and check if the receiver to be linked is really under the control by the transmitter to be linked.

 Always use R203GF 4.8V~7.4V rechargeable battery or regulated output from ESC. If using dry cell batteries, it may cause malfunction. Be sure that when using ESC's regulated output the capacity of the ESC must meet your usage condition.

 In order to maintain complete control of your car/boat it is important that it remains visible at all times. Running behind large objects is not suggested. Doing so may result in the reduction of the quality of the radio frequency link to the model. 4 Safety Precautions Operation Precautions

 WARNING

 When using a NiCd battery to power your system, always charge and check the battery voltage prior to operation. Should the battery discharge below the minimum voltage level, control will be lost.

 Prior to operation always perform a range test. Even one abnormality in the R/C system may cause loss of control.

[Range Test Procedure]

Have a friend hold the model, or place on a stand where the wheels or prop can not come in contact with any object. Operate from a distance of about 100 feet. Be sure to check the movement of each servo to make sure it follows the movement of the steering wheel and throttle trigger. If the servos do not follow the commands from the transmitter or any type of interference is detected, Do Not operate the model.

 Never operate in the rain or run through puddles. The transmitter, receiver, batteries and most servos, and speed controls are not water-

proof. Contact with any type of moisture or immersion in water or snow will cause damage along with possible loss of control. Should any type of moisture enter any component of the system, immediately stop using the R/C system and return it to our service center for inspection.

 Do not operate when visibility is limited. Should you lose sight of the model, a collision or other dangerous situation may occur.

 Do not operate near people or roads. Do not operate on any pond when boats are present. Do not operate near high tension power lines or communication broadcasting antennas. Prior to the operation of any model be sure the area you plan to use is safe. Be aware of all objects that may be in the path of your model. Do not operate the model where people or any type of moveable object could stray in the path of your model. Control loss due to inter-

ference, component failure, loss of sight or low battery voltage could result in serious injury to yourself and others as well as damage to your model.

 Do not operate when you are tired, not feeling well or under the influence of alcohol or drugs. Your judgment is impaired and could result in a dangerous situation that may cause serious injury to yourself and others.

 (Turning on the power switches) Always check the throttle trigger on the transmitter to be sure it is at the neutral position. 1. Turn on the transmitter power switch. 2. Turn on the receiver or speed control power switch.

(Turning off the power switches) Always be sure the engine is not running or the motor is stopped. 1. Turn off the receiver or speed control power switch. 2. Then turn off the transmitter power switch. If the power switches are turned off in the opposite order the model may unexpectedly run out of control and cause a very dangerous situation. Safety Precautions 5

 Make all adjustments to the radio control system with engine not running, or the electric motor disconnected. If the engine is running or the motor is connected while adjustments are made, the model may run out of control.

 Remove the main battery source from electric powered models when they are not being used. Should you accidentally leave the receiver switch on, the model could run out of control.

 (Fail safe function) Before running (cruising), check the fail safe function. Check Method:

Before starting the engine, check the fail safe function as follows:

1. Turn on the transmitter and receiver power switches. 2. Turn off the transmitter power switch. 3. Check if the fail safe function moves the servos to the preset position when reception fails. The fail safe function is a safety feature that minimizes set damage by moving the servos to a preset position when reception fails. However, if set to a dangerous position, it has the opposite effect. Setting example: Throttle idle or brake position

 CAUTION

 Do not touch the engine, motor, speed control or any part of the model that will generate heat while running. Touching hot parts will result in serious burns.

 When the charger is not in use, disconnect it from the outlet. This will prevent accidents, overheating and short circuits. Storage and Disposal Safety Precautions

 WARNING

 At the end of a day's operation, store the system with NiCd battery discharged. Be sure to recharge the system before it is used again. You should fully discharge your system's batteries periodically to prevent a condition called

"memory". For example, if you only make two runs in a day or you regularly use a small amount of battery's capacity, the memory effect can reduce the actual capacity even if the battery is charged for the recommended amount of time.

 Do not throw a Ni-cad battery into a fire. Do not disassemble or attempt to repair a Ni-cad battery pack. Overheating, damage and acid leakage may lead to burns, loss of eye sight as well as nu-

merous other types of injuries. The electrolyte in Ni-cad batteries is a strong alkali. Should you get even the smallest amount of the electrolyte in your eyes, Do Not rub, wash immedi-

ately with water, and seek medical attention at once. The electrolyte can cause blindness. If electrolyte comes in contact with your skin or clothes, wash with water immediately.

 Do not leave the radio system or models within the reach of small children. A small child may accidentally operate the system. This could cause a dangerous situation 6 Safety Precautions and injuries. NiCd batteries can be very dangerous when mishandled and cause chemical damage.

 CAUTION

 Do not store your R/C system where it will be exposed to the following conditions. Extreme heat or coldness Exposed to direct sunlight Where humidity is high Where vibration is prevalent Where dust is prevalent Where there is steam and condensation Storing your R/C system under adverse conditions could cause deformation and numerous other problems with operation.

 If the system will not be used for a long period of time, remove the batteries from the model and store in a cool, dry place. If the batteries are left in the model, electrolyte may leak and damage the model.

<NiCd Battery Recycling>

A used NiCd battery is valuable resource. Insulate the battery terminals and dispose of the battery by taking it to a battery recycling center. Other Safety Precautions

 CAUTION

 When operating two or more models at the same time, have a third person act as a spotter. They will be in charge of safety and you should follow their instructions.

 Beginners should receive instructions regarding safety and operation from an experienced modeler.

 Always use only genuine Futaba transmitter, receivers, servos, and electronic speed controls, along with other optional parts and components. Futaba will not be held responsible for damages caused by other than genuine Futaba parts and components. Use only genuine Futaba parts and components listed in the in-

struction manual and catalog.

 Do not short circuit the Ni-cad battery terminals. Short circuiting the terminals will lead to sparks and overheating and could cause a fire and burns as well. The fuel, motor spray, waste oil and exhaust will penetrate and damage the plastic.

 Do not expose plastic parts to fuel, motor spray, waste oil or exhaust.

<NiCd Battery Electrolyte>

The electrolyte in NiCd batteries is a strong alkali. Should you get even the smallest amount of the electrolyte in your eyes, DO NOT RUB. Wash immediately with water and seek medical attention at once. The electrolyte can cause blindness. If electrolyte comes in contact with your skin or clothes, wash with water immediately. Safety Precautions 7 Before Operation System Contents After opening the container, check the contents for the following items. The contents will vary with the system purchased. Transmitter Receiver Servo E.S.C. Switch 3PRKA-2.4GHz System Contents T3PRKA-2.4G (x1) R203GF (x1)

S3003 (x2) S3003 (x1) S3050 (x1)

MC230CR or MC330CR (x1) MC330CR (x1) SSW-GS (x1)

Miscellaneous

*Servo mounting hardware and servo horns (only w/servo set) Mini Screwdriver NOTE: Futaba FHSS system, T3PRKA-2.4G transmitter and R203GF receiver, does not work with current Futaba FASST system. Please use T3PRKA-2.4G and R203GF in pairs. Futaba FASST system and FHSS system are not compatible each other. Receiver R203GF Servo S3003/S3050 Link Switch LED Connectors

"3" : CH3 Servo

"2" : Throttle Servo (CH2)

"1" : Steering Servo (CH1)

"B": Power connector Servo Horn Mounting Flange 8 Before Operation Transmitter T3PRKA-2.4G Nomenclature / Handling

 WARNING

 A s w i t h a l l r a d i o f r e q u e n c y transmissions, the strongest area of signal transmission is from the sides of the antenna(built-in). As such, the antenna(arrow direction) should not be pointed directly at the model. Throttle Trim Adjusts the throttle in small increments so the model will not move at neutral. Steering Trim Adjusts the steering in small increments so the model will run straight. Front cover Open the cover by sliding it toward left until 'click'. LED Light It blinks at Low Battery. Power Switch When slid upward, the power is turned on. T h r o t t l e E n d Po i n t Adjustment (EPA-CH2) This function is used to adjust the forward and brake side servo travel. CH3 Switch Grip Handle Steering Servo Reversing Switch T h ro t t l e S e r vo Reversing Switch Antenna (Built-in) There is antenna inside of this part. Steering Wheel Turn model to left or right. Throttle Trigger Control the speed of the model and movement forward and backward. Steering Dual Rate Dial (D/R) Adjust the steering sensitivity across the entire range.

 WARNING

 Do not cover/hold the built-in antenna part of T3PRKA-2.4G transmitter by your hand during running. Do not put any conductive plate/sticker on the antenna part. Otherwise, the operating range may become shorter. Before Operation 9

 CAUTION

 A l way s b e s u r e yo u r e i n s e r t t h e batteries in the correct polarity order. If the batteries are loaded incorrectly , the transmitter may be damaged.

 When the transmitter will not be used for any short or long period of time, always remove the batteries. If the batteries do happen to leak , clean the battery case and contacts thorough-

ly. Make sure the contacts are free of corrosion. Check:

Turn the power switch on the transmitter to the ON position. Check the battery voltage display on the LED light. If the voltage is low, check the batteries for insufficient contact in the case or incorrect battery polarity. Low Battery :

When the LED starts blinking, Change the batteries immediately. The low battery alarm is meant to be a safety feature only. Do NOT operate your radio below low battery. Always shut your radio off as soon as possible after the low battery warning tone to avoid loss of control. Battery Replacement Method

(4 AA size batteries) the transmitter by sliding it in the direction of the arrow in the figure. 1 Remove the battery cover from 2 Remove the used batteries. 3 Load the new AA size batteries. Pay very close attention to the polarity markings and reinsert accordingly. 4 Slide the battery cover back onto the case. 10 Before Operation E.S.C. MC230CR / MC330CR Applicable motors (Number of turns is criteria.) Use the MC230CR with a motor with 20T or more turns. Use the MC330CR with a motor with 13T or more turns.

*If a motor with a number of turns smaller than the above is used, the heat protector and overcurrent protection circuit may operate. The number of turns of the motor is a criteria only. Depending on the running conditions, the protection circuit may operate even if the condition above is satisfied. Checker LED Pushbutton switch MC230CR/MC330CR Power switch

(Orange)

(Blue)

(Black)

(Red) Motor connector Connects to the motor.

(Orange) is positive. (Blue) is negative. If the motor rotates in the wrong direction, interchange the connections of this connector. Nicd battery connector Connects to the running Nicd battery.

(Red) is positive. (Black) is negative. Nicd battery 6~7 cells (7.2~8.4V) Receiver connector Connects to the receiver throttle channel. Miniature screwdriver Accessory. Use to press pushbutton switch. the Before Operation 11 Assembly / Adjustment Receiver and Servo Connection As you connect the receiver, servos and other components, do so in accordance with the

"Assembly Precautions". Connections when a E.S.C. MC230CR or MC330CR are used. Connects to Motor Connects to Battery Power Switch E.S.C. Receiver Gas Powered Model Steering Servo Receiver To Receiver Battery Power Switch Throttle Servo Steering Servo Receiver Antenna Installation Install the R203GF receiver on the car as follows:

Note: The operating range may become shorter, depending on where the receiver and the antenna are mounted.

 WARNING

 Install the antenna in the higher place as shown in the figure. Keep the antenna as for away from the motor, ESC and other noise sources as possible. Put the antenna in the antenna tube to protect it.

 Do not cut the antenna. Do not bend the coaxial cable. Doing so causes damage. Antenna tube Antenna Coaxial cable R203GF 12 Assembly / Adjustment Assembly Precautions

 WARNING

 Check the receiver, servos, and battery connectors, to be sure they are firmly connected. If a connector is not fully inserted, vibration may cause the connector to work loose while the model is operating. This will result in loss of control.

 Operate each servo horn over its full stroke and check to see that the linkage does not bind or is not too loose. Excessive force applied to the servo horn by binding or poor installation may lead to servo problems and result in loss of control.

 Electric Cars and Boats) Isolate the receiver from vibration by attaching to the chassis or mounting plate with thick double sided tape.

(Gas Powered Cars and Boats) Isolate the receiver from vibration by wrapping it in foam rubber or similar type cushioning material. Protect the unit from water damage by placing it in a plastic bag or waterproof ra-

dio box. The receiver contains precision electronic parts. These parts are vulnerable to vibration and shock. Any contact with moisture (water or condensation) may cause receiver malfunction and loss of control.

 Keep all devises that omit high frequency noise, such as motors, batteries, and wiring that handles heavy current loads, at least 1/2 inch away from the receiver and the receiver antenna. High frequency noise will cause a decrease in operating range and could cause loss of control.

 Install electronic speed control heat sinks as well as other components that conduct electricity so they can not come in contact with aluminum, carbon fiber or other materials that conduct electricity. If, for example, the speed control came loose while the model was running and touched an aluminum chassis, a short circuit may occur that would cause irreparable damage to the system as well as loss of control.

 Noise suppression capacitors should be installed on almost all motors. If the proper capacitors are not installed, high frequency noise will reduce range and cause loss of control along with various other problems.

 Inspect all linkage installations and any point where metal could come in contact with other metal parts. Make sure these parts do not touch other metal parts under vibration. Should a linkage or other metal parts come in contact with other metal parts under vibra-

tion, the high frequency noise generated by this contact will cause interference and pos-

sible loss of control.

 CAUTION

 Do Not disassemble any part of this system that is not specified in the instruction manual. Futaba will not be responsible for any damage due to improper disassembly of any part of the radio control system. Assembly / Adjustment 13 How to link the transmitter and the receiver Each transmitter has an individually assigned, unique ID code. In order to start operation, the receiver must be linked with the ID code of the transmitter with which it is being paired. Once the link is made, the ID code is stored in the receiver and no further linking is necessary unless the receiver needs to be used with an other transmitter. (For T/R set, the link is already done at factory.) Link procedure to each other, within one meter. 1 Bring the transmitter and the receiver close 2 Turn on the transmitter and the receiver. 3 Push and hold the Link Switch of the 4 When the link is complete, the LED in the receiver changes to solid green. receiver.

*Please refer the table below for LED status vs receiver's condition. Link Switch LED LED status vs receiver's condition:

No signal reception OFF Receiving signals Receiving signals, but ID is unmatched. On Blink Receiving signals, when F/S is set. It is an fast blink for the first one second. How to open front cover The switch and the trimmer which adjusts it are in the front cover. Open the cover by sliding it toward left until 'click'.  Do not open forcely the cover 90or more.

'Click'

14 Assembly / Adjustment Transmitter Set-Up Procedures

*When making these settings adjustments, do so with the motor disconnected or the engine not running. Servo Horn Installation Instructions

*Both servos will move to the neutral position. then turn on the power switches to transmitter and receiver. 1 Connect the receiver, servos, and other components and 2 At this time install the servo horn in the manner described in the instruction manual provided with the model this system will be used in. Reversing The Servo Operation Direction Should the ser vo operate in the opposite direction required for your application, reverse the direction with the servo reversing. Steering Servo Reversing Throttle Servo Reversing Nor: Normal Rev: Reverse E.S.C. MC230CR / MC330CR NEUTRAL, HIGH, AND BRAKE MAX POINTS SETTINGS Set the steering angle adjustment function (ATV) to 100% and the ABS function and acceleration function to OFF using the transmitter throttle channel function. If the steering angle is too large or the ABS and acceleration functions are on, erroneous operation may occur.

*When using the ABS function, after setting up the MC230CR / MC330CR, stop the reverse function, then turn on the ABS function. If the ABS function is on, the MC231CR / MC331CR cannot be set up correctly. Before setting each point, set the transmitter throttle channel trim to neutral. 1 Turn on the power in transmitter -> amp order. Transmitter throttle operation MC230CR /MC330CR

(Pushbutton switch operation)

(Checker LED) 2 Neutral point setting 3 High point setting 4 Brake MAX point setting Neutral state Press the pushbutton switch.

(0.5 secs or longer)

(Confirmation beep sounds) Continuous single blink Full high state Press the pushbutton switch.

(Confirmation beep sounds) Continuous double blink N N Full High Full brake state N Full brake Press the pushbutton switch.

(Confirmation beep sounds.) If the LED goes out, setting is complete.

* Since the data is read at the end of setting of all points, the points cannot be set independently.

* If the amp power was turned off during setting, the setting points cannot be memorized. (The previous settings are retained.)

* The confirmation beep sounds only when the motor was connected. If the LED does not go off but blinks rapidly, setting was not performed normally. Repeat setting from "Neutral point setting". Continuous rapid blink Assembly / Adjustment 15 3PRKA-2.4G Functions Steering Trim Steering neutral adjustments can be made by moving the Steering trim knob to the left or right. Racers Tip When you install a servo, always check to be sure the servo is at its neutral position. Adjust the servo horn hole position and linkage so both are parallel. When a servo saver is used, place it as close to center position as possible. Be sure the steering trim on the transmitter is at the neutral position. Trim Operation And Maximum Travel Changing the trim can affect the overall settings. When adjustments are made with the trims, recheck your installation for maximum travel. (Steering D/R). When Trim usage is extreme If it takes most of your trim movement to get a servo to the neutral position, reposition the servo horn or servo saver on the servo and inspect your linkage installation. Steering Trim Direct Servo Saver Horn Servo Saver 90 90 Parallel Throttle Trim Throttle neutral adjustments can be made moving the throttle trim to the left or right. Racers Tip When using an electronic speed control, set the throttle trim to neutral and make adjustments to the speed control. On a gas powered model, set the trim to neutral and adjust the linkage to the point where the carburetor is fully closed in accordance with the engine instruction manual. Trim Operation and Travel Trim adjustments will affect the overall servo travel. Check the brake side (backward) movement when changes are made. When trim movement is extreme If you use most of the trim movement to get the servo to the neutral position , recenter the servo horn closer to the neutral position and inspect your throttle linkage. 16 3PRKA Functions Throttle Trim Carburetor Fully Closed

(Drum Type)

(Slide Type) Steering Dual Rates Use this function to adjust the steering travel of your model. If the model understeers (push) while cornering, add steering by pressing the upper side of the D/R button. When the model oversteers (loose), take away steering by pressing the lower side of the D/R button.

 WARNING

 Be sure that the steering linkage does not bind or come in contact with any suspension parts or arms. If unreasonable force is applied to the servo, the servo may be damaged and result in loss of control. Steering Dual Rates Steering Servo Reversing This function reverses the rotation direction of the Steering servo. Steering Servo Reverse When the trim position deviates from the center, the deviation will be on the opposite side when the servo is reversed. Nor: Normal Rev: Reverse Throttle Servo Reversing This function reverses the rotation direction of the throttle servo. Throttle Servo Reversing (REV-CH2) Throttle Servo Reverse When the trim position deviates from the center, the deviation will be on the opposite side when the servo is reversed. Nor: Normal Rev: Reverse 3PRKA Functions 17 Throttle End Point Adjustment(EPA) This function is used to adjust the forward and brake side servo travel. Each direction can be adjusted independent of each other. Use this feature to set the throttle servo travel. When ESC is used with an electric car, two EPA trimmers are right fully turned beforehand. Thrittle EPA Hight: Forward side

 WARNING

 Be sure that your throttle linkage does not apply excessive force to the servo. If your linkage installation causes an unreasonable amount of force to be applied to the servo, the servo may be damaged and result in loss of control. Low: Brake side Steering End Point Adjustment(EPA) : onry U.S.A Use this function to limit the servo movement to the left or right. The servo travel to each side can be independently adjusted.This feature will compensate for any difference in right or left turning angles or radius due to the characteristics of your model. Steering EPA

 WARNING

 Be sure that the steering linkage does not bind or come in contact with any suspension parts or arms. If unreasonable force is applied to the servo, the servo may be damaged and result in loss of control. Low: Right side Hight: Left side CH3 Function One another Channel can be used besides the steering wheel and the throttle operation. Right and left operation of two actions can be done by using the servo. ON-OFF the headlight etc. can be operated by using "CPS-1 "of sales separately . CH3 cannot operate EPA function and servo linearly. Fail Safe Function (F/S) CH3 Switch This function moves the throttle servo to a preset position when the receiver cannot receive the signal from the transmitter for some reason. W h e n t h e s i g n a l f r o m t h e transmitter can be received again, this function automatically resets. The throttle position at the link operation is memorized.(P.14) 18 3PRKA Functions For an electric car (E.C.S use), link the transmitter and the receiver at neutral position. For the engine car, link the transmitter and the receiver at braking position. MC230CR/MC330CR CANCELLING THE REVERSE FUNCTION The amp reverse function can be cancelled by the following method so that the model can be used even in races that prohibit reverse running. (Brake operation only) MC230CR / MC330CR

(Pushbutton switch operation)

(Power switch) 1 Reverse function cancellation While pressing the pushbutton switch, ON set the power switch to ON.

* When desired, you can enable the cancelled reverse function by repeating the operation shown at the left.

(The reverse function is switched alternately.) BRAKE/REVERSE OPERATING INSTRUCTIONS Operation can be switched to reverse operation by returning the throttle trigger (or throttle stick) from the brake position to the neutral position. PROTECTION CIRCUIT OPERATION The following protection circuits are built into the MC230CR / MC330CR. When a protection circuit operates, remove the cause before operating the model again. Overcurrent protection Heat protector Low voltage operation When an overcurrent flows due to an output short circuit, etc., the overcurrent protection circuit automatically limits the current to protect the FET. Remove the cause of the short circuit, etc. before operating the model again. When abnormal heating of the FET due to an overload, etc. is detected, the heat protector operates so that the speed is gradually reduced. When the FET temperature drops, the heat protector automatically resets. However, remove the cause of the overheating before operating the model again. When the Nicd battery voltage drops, this function limits the motor output current and ensures steering operation. After the speed drops, immediately recover the vehicle. CHECKER LED DISPLAY The amp operates linearly in proportion to the amount of forward, reverse, and brake operation. The amp operating state can be checked with the checker LED as shown below. Operation Checker LED display Amp power ON

(Reverse operation set) Single blink

(Single confirmation beep)

(Only brake operation set) Double blink

(Two confirmation beeps) High point Forward Neutral point Reverse

/brake Brake MAX point Off On Off On Off

*Becomes brighter nearer the high point.

*Becomes brighter nearer the brake MAX point.

(Amp power left on alarm) When the transmitter power was turned off first. Blinks. (Confirmation beep also sounds.)

*Not used with PCM receivers.

*When the transmitter is OFF, this function is not performed in environments such that the servo operates erroneously. Not sure what this is supposed to mean in yellow.

* Confirmation beep only sounds when the motor was connected. 3PRKA Functions 19 Reference

*Specifications and ratings are subject to change without prior notice. Ratings Communication method:

One-way operation system Maximum operating range:

80m (Optimum condition) For safety:

F/S (Throttle), ID (About 4 billion ways of pair identifications) Transmitter T3PRKA

(FHSS system, wheel type, 3 channels) Transmitting frequency:

2.4GHz band Power requirement:

(Dry cell battery) Penlight x 4(6V) Current drain:

100mA or less Transmission antenna:

1/2 di-pole (Built-in) Receiver R203GF:

(FHSS/S-FHSS system, 3 channels) Power requirement:

4.8V 7.4V Rechargeable battery Size:

26x39x10mm (excluding a projection part) Weight:

8g Servo S3003

(Standard servo) Power requirement:

6V (common with receiver) Current drain:

8mA (at 6V / Idle) Output torque:

4.1kg-cm (57in.-oz.) at 6V Operating speed:

0.19sec/60 degree at 6V Size:

40.4x19.8x36mm (1.59x0.78x1.42in.) Weight:

37.2g (1.31oz.) Servo S3050

(Standard digital servo) Power requirement:

6V (common with receiver) Current drain:

8mA (at 6V / Idle) Output torque:

6.5kg-cm (90.3oz.-in.) at 6V Operating speed:

0.16sec/60 degree at 6V Size:

40.0x20.0x38.1mm (1.57x0.79x1.50in.) Weight:

49g (1.72oz.) E.S.C. MC230CR / MC330CR

(Electronic speed control) Operating system:

Forward, reverse, and brake operations are all linear. Power requirement:

Nicd battery 6-7 cells (7.2 to 8.4V) PWM frequency:

1.5kHz (fixed) Setting:

One-touch input by pushbutton switch. Set data is saved to built-in EEPROM. Current capacity (FET rating):

Forward=90A/200A, reverse=45A/100A Size:

27.1x33.3x12.8mm (1.07x1.31x0.50in.)

(excluding protruding parts) Silicon cord gauge size:

AWG16/AWG14 equivalent Weight:

44/45g (1.55/1.59oz.)

(including connectors and switches) BEC voltage:

6.0V NOTE: Futaba FHSS system, T3PRKA transmitter and R203GF receiver, does not work with current Futaba FASST system. Please use T3PRKA and R203GF in pairs. Futaba FASST system and FHSS system are not compatible each other. 20 Reference Troubleshooting If your system fails to operate or you experience a short range problem or erratic control, check the table below for possible causes. If after you have followed the suggestions listed the problem is not corrected, return the system to our service department for inspection and repair.

(Item Check) Transmitter Battery Change the batteries. Dead battery Batteries inserted incorrectly. polarity markings Faulty contact contact Dirty contacts Reload the batteries in accordance with the Check to see if the contacts are bent and not making good Clean the contacts and check for corrosion. Receiver Battery Dead battery Wrong polarity Replace or recharge Check connections Antenna Near other wiring Was antenna cut Is the antenna installed correctly Move away from wiring Request repair Refer to the receiver installation. Monitor LED Check the LED of the receiver. Refer to the "How to link the transmitter and the receiver". Connector connections Wiring incorrect Loose connections Insert all connectors firmly Push the connector in firmly Linkage Binding or loose Is movement stiff Adjust the linkage in model Adjust linkage in model Motor (Electric powered) Noise problems Install capacitors on motor Reference 21 Error Displays Low Battery When the LED starts blinking, Change the batteries immediately. LED light:

 WARNING

 When a low battery alarm is generated, cease operation immediately and retrieve the model. If the battery goes dead while in operation, you will lose control. When requesting repair Before requesting repair, read this instruction again and recheck your system. Should the problems continue, request as follows.

(Information needed for repair) Describe the problem in as much detail as possible and send the letter along with the system in question. Symptom (Including the conditions and when the problem occurred) R/C System (Send transmitter, receiver and servos) Model (Type of model, brand name and model number or kit name) Detailed packing list (Make a list of all items sent in for repair) Your name, address and telephone number.

(Warranty) Read the Warranty card. When requesting warranty service, send the card or some type of dated proof of purchase. Hobby Services (U.S. only) 3002 N. Apollo Drive, Suite 1 Champaign, IL 61822 U.S.A. Phone: (217) 398-0007 www.hobbyservices.com FUTABA CORPORATION Phone: +81 475 32 6982, Facsimile: +81 475 32 6983 1080 Yabutsuka, Chosei-mura, Chosei-gun, Chiba-ken, 299-4395, Japan 22 Reference FUTABA CORPORATION 2011, 03 (1) When requesting repair

Thank you for purchasing a Futaba FHSS 2POK 2.4GHz system. This system is based on the combination of the newly developed 2.4GHz transmitter and its corresponding receiver. Before using your 2POK 2.4GHz system, read this manual carefully and use your R/C set safely. After reading this manual, store it in a safe place. FHSS 2POK 2.4GHz system 2.4GHzSS (Spread Spectrum) radio communication system Frequency channel setting unnecessary: Sifting the channels within the 2.4GHz band automatically, this system minimizes the interference from other 2.4GHz systems. Accepts no unwanted signals by using ID code Built-in antenna (T2POK-2.4G transmitter) FHSS (Frequency Hopping Spread Spectrum) minimizes interference from other 2.4GHz systems. This system is not compatible with FASST. Application, Export, and Modification 1. This product may be used for models only. It is not intended for use in any application other than the control of models for hobby and recreational purposes. 2. Exportation precautions:

(a) When this product is exported from the country of manufacture, its use is to be approved by the laws governing the country of destination which govern devices that emit radio frequencies. If this product is then re-exported to other countries, it may be subject to restrictions on such export. Prior approval of the appropriate government authorities may be required. If you have purchased this product from an exporter outside your country, and not the authorized Futaba distributor in your country, please contact the seller immediately to determine if such export regulations have been met.

(b) Use of this product with other than models may be restricted by Export and Trade Control Regulations, and an application for export approval must be submitted. 3. Modification, adjustment, and replacement of parts: Futaba is not responsible for unauthorized modification, adjustment, and replacement of parts on this product. Any such changes may void the warranty. Compliance Information Statement (for U.S.A.) This device, trade name Futaba Corporation of America, model number R203GF, complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause undesired operation.

*This module meets the requirements for a mobile device that may be used at separation distances of more than 20cm from the human body. To meet the RF exposure requirements of the FCC this device shall not be co-located with another transmitting device. The responsible party of this device compliance is:

3002 N Apollo Drive Suite 1, Champaign, IL 61822 U.S.A. TEL (217)398-8970 or E-mail: support@futaba-rc.com (Support) TEL (217)398-0007 or E-mail: service@futaba-rc.com (Service) Battery Recycling (for U.S.A.) The RBRCTM SEAL on the (easily removable) nickel-cadmium battery contained in Futaba products indicates that Futaba Corporation of America is voluntarily participating in an industry program to collect and recycle these batteries at the end of their useful lives, when taken out of service within the United States. The RBRCTM program provides a convenient alternative to placing used nickel-cadmium batteries into the trash or municipal waste system, which is illegal in some areas. You may contact your local recycling center for information on where to return the spent battery. Please call 1-800-8-BATTERY for information on Ni-Cd battery recycling in your area. Futaba Corporation of America's involvement in this program is part of its commitment to protecting our environment and conserving natural resources. RBRCTM is a trademark of the Rechargeable Battery Recycling Corporation. Table of Contens Safety Precautions ............................. 4 Definition of Symbols ............................................................ 4 2.4GHz System Precautions ................................................. 4 Operation Precautions .......................................................... 5 Storage and Disposal Safety Precautions ........................... 6 Other Safety Precautions ...................................................... 7 Before Operation ................................ 8 System Contents .................................................................... 8 Nomenclature / Handling ....................................................... 9 Assembly / Adjustment ..................... 12 Receiver and Servo Connection ......................................... 12 Receiver Antenna Installation ............................................. 12 Assembly Precautions ........................................................ 13 How to Link Transmitter and Receiver ............................... 14 Fail Safe Function (F/S) ....................................................... 14 Transmitter Set-Up Procedures .......................................... 15 2POK-2.4G Functions ........................ 16 Steering Trim ....................................................................... 16 Throttle Trim ........................................................................ 16 Steering Dual Rates (D/R) .................................................. 17 Steering Servo Reversing .................................................. 17 Throttle Servo Reversing ................................................... 17 MC230CR/MC330CR ............................................................ 18 Reference .......................................... 19 Ratings .................................................................................. 19 Troubleshooting ................................................................... 20 Error Displays ...................................................................... 21 When Requesting Repair ..................................................... 21 Safety Precautions Before Operation Assembly /

Adjustment 3PRKA-2.4G Functions Reference Warning: This product contains a chemical known to cause cancer and birth defects (or other reproductive harm). No part of this manual may be reproduced in any form without prior permission. The contents of this manual are subject to change without prior notice. This manual has been carefully written. Please write to Futaba if you feel that any corrections or clarifications should be made. Futaba is not responsible for the use of this product. 3 Safety Precautions For your safety as well as that of others, please read this manual thoroughly prior to installation and operation of your digital proportional R/C system. Definition of Symbols The following defines the symbols used in this manual. Explanation of Symbols

 DANGER Procedures which may lead to a dangerous condition and cause death or serious injury to the user if not carried out properly. Procedures which may lead to a dangerous condition or cause death or serious injury to the user if not carried out properly, or procedures where the probability of superficial injury or physical damage is high.

 WARNING

 CAUTION Procedures where the possibility of serious injury to the user is small, but there is a danger of injury, or physical damage, if not carried out properly. Explanation of Graphic Symbols

 Indicates an operation that prompts a warning (including Caution).

 Indicates an operation that must not be performed.

 Indicates an operation that always must be performed. 2.4GHz System Precautions

 WARNING

 Do not cover/hold the built-in antenna part of T2POK-2.4G transmitter by your hand during running. Do not put any conductive plate/sticker on the antenna part. Otherwise, the operating range may become shorter.

 Do not perform the linking procedure while motor's main wire is connected or the engine is operating as it may result in serious injury.

 While the linking is done, please cycle receiver power and check if the receiver to be linked is really under the control by the transmitter to be linked.

 Always use R203GF 4.8V~7.4V rechargeable battery or regulated output from ESC. Using dry cell batteries may cause the system to malfunction. When using an ESC, be sure that the regulated output capacity meets your usage condi-

tion.

 In order to maintain complete control of your car/boat it is important that it remains visible at all times. Running behind large objects is not suggested. Doing so may result in the reduction of the quality of the radio frequency link to the model. 4 Safety Precautions Operation Precautions

 WARNING

 When using a Ni-Cd battery to power your system, always charge and check the battery voltage prior to operation. Should the battery discharge below the minimum voltage level, control will be lost.

 Prior to operation always perform a range test. Even one abnormality in the R/C system may cause loss of control.

[Range Test Procedure]

Have a friend hold the model, or place on a stand where the wheels or prop can not come in contact with any object. Operate from a distance of about 100 feet. Be sure to check the movement of each servo to make sure it follows the movement of the steering wheel and throttle trigger. If the servos do not follow the commands from the transmitter or any type of interference is detected, Do Not operate the model.

 Never operate in the rain or run through puddles. The transmitter, receiver, batteries and most servos, and speed controls are not water-

proof. Contact with any type of moisture or immersion in water or snow will cause damage along with possible loss of control. Should any type of moisture enter any component of the system, immediately stop using the R/C system and return it to our service center for inspection.

 Do not operate when visibility is limited. Should you lose sight of the model, a collision or other dangerous situation may occur.

 Do not operate near people or roads. Do not operate on any pond when boats are present. Do not operate near high tension power lines or communication broadcasting antennas. Prior to the operation of any model be sure the area you plan to use is safe. Be aware of all objects that may be in the path of your model. Do not operate the model where people or any type of moveable object could stray in the path of your model. Control loss due to inter-

ference, component failure, loss of sight or low battery voltage could result in serious injury to yourself and others as well as damage to your model.

 Do not operate when you are tired, not feeling well or under the influence of alcohol or drugs. Your judgment is impaired and could result in a dangerous situation that may cause serious injury to yourself and others.

 (Turning on the power switches) Always check the throttle trigger on the transmitter to be sure it is at the neutral position. 1. Turn on the transmitter power switch. 2. Turn on the receiver or speed control power switch.

(Turning off the power switches) Always be sure the engine is not running or the motor is stopped. 1. Turn off the receiver or speed control power switch. 2. Then turn off the transmitter power switch. If the power switches are turned off in the opposite order the model may unexpectedly run out of control and cause a very dangerous situation. Safety Precautions 5

 Make all adjustments to the radio control system with engine not running, or the electric motor disconnected. If the engine is running or the motor is connected while adjustments are made, the model may run out of control.

 Remove the main battery source from electric powered models when they are not being used. Should you accidentally leave the receiver switch on, the model could run out of control.

 (Fail safe function) Before running (cruising), check the fail safe function. Check Method:

Before starting the engine, check the fail safe function as follows:

1. Turn on the transmitter and receiver power switches. 2. Turn off the transmitter power switch. 3. Check if the fail safe function moves the servos to the preset position when reception fails. The fail safe function is a safety feature that minimizes set damage by moving the servos to a preset position when reception fails. However, if set to a dangerous position, it has the opposite effect. Setting example: Throttle idle or brake position

 CAUTION

 Do not touch the engine, motor, speed control or any part of the model that will generate heat while running. Touching hot parts will result in serious burns.

 When the charger is not in use, disconnect it from the outlet. This will prevent accidents, overheating and short circuits. Storage and Disposal Safety Precautions

 WARNING

 At the end of a day's operation, store the system with Ni-Cd battery discharged. Be sure to recharge the system before it is used again. You should fully discharge your system's batteries periodically to prevent a condition called

"memory". For example, if you only make two runs in a day or you regularly use a small amount of battery's capacity, the memory effect can reduce the actual capacity even if the battery is charged for the recommended amount of time.

 Do not throw a Ni-Cd battery into a fire. Do not disassemble or attempt to repair a Ni-cad battery pack. Overheating, damage and acid leakage may lead to burns, loss of eye sight as well as nu-

merous other types of injuries. The electrolyte in Ni-cad batteries is a strong alkali. Should you get even the smallest amount of the electrolyte in your eyes, Do Not rub. Wash immedi-

ately with water, and seek medical attention at once. The electrolyte can cause blindness. If electrolyte comes in contact with your skin or clothes, wash with water immediately.

 Do not leave the radio system or models within the reach of small children. A small child may accidentally operate the system. This could cause a dangerous situation 6 Safety Precautions and injuries. NiCd batteries can be very dangerous when mishandled and cause chemical damage.

 CAUTION

 Do not store your R/C system where it will be exposed to the following conditions. Extreme heat or coldness Exposed to direct sunlight Where humidity is high Where vibration is prevalent Where dust is prevalent Where there is steam and condensation Storing your R/C system under adverse conditions could cause deformation and numerous other problems with operation.

 If the system will not be used for a long period of time, remove the batteries from the model and store in a cool, dry place. If the batteries are left in the model, electrolyte may leak and damage the model.

<Ni-Cd Battery Recycling>

A used Ni-Cd battery is valuable resource. Insulate the battery terminals and dispose of the battery by taking it to a battery recycling center. Other Safety Precautions

 CAUTION

 When operating two or more models at the same time, have a third person act as a spotter. They will be in charge of safety and you should follow their instructions.

 Beginners should receive instructions regarding safety and operation from an experienced modeler.

 Always use only genuine Futaba transmitter, receivers, servos, and electronic speed controls, along with other optional parts and components. Futaba will not be held responsible for damages caused by other than genuine Futaba parts and components. Use only genuine Futaba parts and components listed in the in-

struction manual and catalog.

 Do not short circuit the Ni-cad battery terminals. Short circuiting the terminals will lead to sparks and overheating and could cause a fire and burns as well. The fuel, motor spray, waste oil and exhaust will penetrate and damage the plastic.

 Do not expose plastic parts to fuel, motor spray, waste oil or exhaust.

<Ni-Cd Battery Electrolyte>

The electrolyte in NiCd batteries is a strong alkali. Should you get even the smallest amount of the electrolyte in your eyes, DO NOT RUB. Wash immediately with water and seek medical attention at once. The electrolyte can cause blindness. If electrolyte comes in contact with your skin or clothes, wash with water immediately. Safety Precautions 7 Before Operation System Contents After opening the container, check the contents for the following items. The contents will vary with the system purchased. Transmitter Receiver Servo E.S.C. Switch 2POK-2.4GHz System Contents T2POK-2.4G (x1) R203GF (x1)

S3003 (x2) S3003 (x1) S3050 (x1)

MC230CR or MC330CR (x1) MC330CR (x1) SSW-GS (x1)

Miscellaneous

*Servo mounting hardware and servo horns (only w/servo set) Mini Screwdriver NOTE: Futaba FHSS system, T2POK-2.4G transmitter and R203GF receiver, does not work with current Futaba FASST systems. Please use T2POK-2.4G and R203GF in pairs. Futaba FASST system and FHSS system are not compatible each other. Receiver R203GF Servo S3003/S3050 Link Switch LED Connectors

"3" : CH3 Servo

"2" : Throttle Servo (CH2)

"1" : Steering Servo (CH1)

"B": Power connector Servo Horn Mounting Flange 8 Before Operation Transmitter T2POK-2.4G Nomenclature / Handling

 WARNING

 A s w i t h a l l r a d i o f r e q u e n c y transmissions, the strongest area of signal transmission is from the sides of the antenna(built-in). As such, the antenna(arrow direction) should not be pointed directly at the model. Throttle Trim Adjusts the throttle in small increments so the model will not move at neutral. Steering Trim Adjusts the steering in small increments so the model will run straight. ST.TRIM TH.TRIM 2CHANNEL SYSTEM SERVO REV POWER ST.D/R N R ST. TH. LED Light It blinks at Low Battery. Power Switch When slid upward, the power is turned on. Steering Servo Reversing Switch T h ro t t l e S e r vo Reversing Switch Grip Handle Antenna (Built-in) The antenna is inside this part. Steering Wheel Turn model to left or right. Throttle Trigger Control the speed of the model and movement forward and backward. Steering Dual Rate Dial (D/R) Adjust the steering sensitivity across the entire range.

 WARNING

 Do not cover/hold the built-in antenna part of T2POK-2.4G transmitter by your hand during running. Do not put any conductive plate/sticker on the antenna part. Otherwise, the operating range may become shorter. Before Operation 9 Battery Replacement Method

(4 AA size batteries) the transmitter by sliding it in the direction of the arrow in the figure. 1 Remove the battery cover from 2 Remove the used batteries. 3 Load the new AA size batteries. Pay very close attention to the polarity markings and reinsert accordingly. 4 Slide the battery cover back onto the case. 10 Before Operation

 CAUTION

 A l way s b e s u r e yo u r e i n s e r t t h e batteries in the correct polarity order. If the batteries are loaded incorrectly,the transmitter may be damaged.

 When the transmitter will not be used for any short or long period of time, always remove the batteries. If the batteries do happen to leak, clean the battery case and contacts thorough-

ly. Make sure the contacts are free of corrosion. Check:

Turn the power switch on the transmitter to the ON position. Check the battery voltage display on the LED light. If the voltage is low, check the batteries for insufficient contact in the case or incorrect battery polarity. Low Battery :

When the LED starts blinking, change the batteries immediately. ST.TRIM TH.TRIM 2CHANNEL SYSTEM SERVO REV POWER ST.D/R N R ST. TH. The low battery alarm is meant to be a safety feature only. Do NOT operate your radio below low battery. Always shut your radio off as soon as possible after the low battery warning tone to avoid loss of control. E.S.C. MC230CR / MC330CR Applicable motors (Number of turns is criteria.) Use the MC230CR with a motor with 20T or more turns. Use the MC330CR with a motor with 13T or more turns.

*If a motor with a number of turns smaller than the above is used, the heat protector and overcurrent protection circuit may operate. The number of turns of the motor is only one criteria. Depending on the running conditions, the protection circuit may operate even if the condition above is satisfied. Checker LED Pushbutton switch MC230CR/MC330CR Power switch

(Orange)

(Blue)

(Black)

(Red) Motor connector Connects to the motor.

(Orange) is positive. (Blue) is negative. If the motor rotates in the wrong direction, interchange the connections of this connector. Nicd battery connector Connects to the running Nicd battery.

(Red) is positive. (Black) is negative. Nicd battery 6~7 cells (7.2~8.4V) Receiver connector Connects to the receiver throttle channel. Miniature screwdriver Accessory. Use to press pushbutton switch. the Before Operation 11 Assembly / Adjustment Receiver and Servo Connection As you connect the receiver, servos and other components, do so in accordance with the

"Assembly Precautions". Connections when a E.S.C. MC230CR or MC330CR are used. Connects to Motor Connects to Battery Power Switch E.S.C. Receiver Gas Powered Model Steering Servo Receiver To Receiver Battery Power Switch Throttle Servo Steering Servo Receiver Antenna Installation Install the R203GF receiver on the car as follows:

Note: The operating range may become shorter, depending on where the receiver and the antenna are mounted.

 WARNING

 Install the antenna in the higher place as shown in the figure. Keep the antenna as far away from the motor, ESC and other noise sources as possible. Put the antenna in the antenna tube to protect it.

 Do not cut the antenna. Do not bend the coaxial cable. Doing so causes damage. Antenna tube Antenna Coaxial cable R203GF 12 Assembly / Adjustment Assembly Precautions

 WARNING

 Check the receiver, servos, and battery connectors, to be sure they are firmly connected. If a connector is not fully inserted, vibration may cause the connector to work loose while the model is operating. This will result in loss of control.

 Operate each servo horn over its full stroke and check to see that the linkage does not bind or is not too loose. Excessive force applied to the servo horn by binding or poor installation may lead to servo problems and result in loss of control.

 (Electric Cars and Boats) Isolate the receiver from vibration by attaching to the chassis or mounting plate with thick double sided tape.

(Gas Powered Cars and Boats) Isolate the receiver from vibration by wrapping it in foam rubber or similar type cushioning material. Protect the unit from water damage by placing it in a plastic bag or waterproof ra-

dio box. The receiver contains precision electronic parts. These parts are vulnerable to vibration and shock. Any contact with moisture (water or condensation) may cause receiver malfunction and loss of control.

 Use the servo horn screw. When the servo horn comes off, it becomes loss of control.

 Keep all devices that emit high frequency noise, such as motors, batteries, and wiring that handles heavy current loads, at least 1/2 inch away from the receiver and the receiver antenna. High frequency noise will cause a decrease in operating range and could cause loss of control.

 Install electronic speed control heat sinks as well as other components that conduct electricity so they can not come in contact with aluminum, carbon fiber or other materials that conduct electricity. If, for example, the speed control came loose while the model was running and touched an aluminum chassis, a short circuit may occur that would cause irreparable damage to the system as well as loss of control.

 Noise suppression capacitors should be installed on almost all motors. If the proper capacitors are not installed, high frequency noise will reduce range and cause loss of control along with various other problems.

 Inspect all linkage installations and any point where metal could come in contact with other metal parts. Make sure these parts do not touch other metal parts under vibration. Should a linkage or other metal parts come in contact with other metal parts under vibra-

tion, the high frequency noise generated by this contact will cause interference and pos-

sible loss of control.

 CAUTION

 Do Not disassemble any part of this system that is not specified in the instruction manual. Futaba will not be responsible for any damage due to improper disassembly of any part of the radio control system. Assembly / Adjustment 13 How to link the transmitter and the receiver Each transmitter has an individually assigned, unique ID code. In order to start operation, the receiver must be linked with the ID code of the transmitter with which it is being paired. Once the link is made, the ID code is stored in the receiver and no further linking is necessary unless the receiver needs to be used with an other transmitter. (For T/R set, the link is already done at factory.) Link procedure to each other, within one meter. 1 Bring the transmitter and the receiver close 2 Turn on the transmitter and the receiver. 3 Push and hold the Link Switch of the 4 When the link is complete, the LED in the receiver changes to solid green. receiver.

*Please refer the table below for LED status vs receiver's condition. Link Switch LED LED status vs receiver's condition:

No signal reception OFF Receiving signals Receiving signals, but ID is unmatched. Receiving signals, when F/S is set. On Blink It is turns on and a fast blink for the first one second. Fail Safe Function (F/S) This function moves the throttle servo to a preset position when the receiver cannot receive the signal from the transmitter for some reason. W h e n t h e s i g n a l f r o m t h e transmitter can be received again, this function automatically resets. The throttle position at the link operation is memorized. 14 Assembly / Adjustment For an electric car (E.C.S use), link the transmitter and the receiver at neutral position. For the engine car, link the transmitter and the receiver at braking position. Transmitter Set-Up Procedures

*When making these settings adjustments, do so with the motor disconnected or the engine not running. Servo Horn Installation Instructions

*Both servos will move to the neutral position. then turn on the power switches to transmitter and receiver. 1 Connect the receiver, servos, and other components and 2 At this time install the servo horn in the manner described in the instruction manual provided with the model this system will be used in. Reversing The Servo Operation Direction Should the ser vo operate in the opposite direction required for your application, reverse the direction with the servo reversing. Steering Servo Reversing Nor: Normal Rev: Reverse Throttle Servo Reversing SERVO REV N R ST. TH. E.S.C. MC230CR / MC330CR NEUTRAL, HIGH, AND BRAKE MAX POINT SETTINGS Set the steering angle adjustment function (ATV) to 100% and the ABS function and acceleration function to OFF using the transmitter throttle channel function. If the steering angle is too large or the ABS and acceleration functions are on, erroneous operation may occur.

*When using the ABS function, after setting up the MC230CR / MC330CR, stop the reverse function, then turn on the ABS function. If the ABS function is on, the MC231CR / MC331CR cannot be set up correctly. Before setting each point, set the transmitter throttle channel trim to neutral. 1 Turn on the power in transmitter -> amp order. Transmitter throttle operation MC230CR /MC330CR

(Pushbutton switch operation)

(Checker LED) 2 Neutral point setting 3 High point setting 4 Brake MAX point setting Neutral state Press the pushbutton switch.

(0.5 secs or longer)

(Confirmation beep sounds) Continuous single blink Full high state Press the pushbutton switch.

(Confirmation beep sounds) Continuous double blink N N Full High Full brake state N Full brake Press the pushbutton switch.

(Confirmation beep sounds.) If the LED goes out, setting is complete.

* Since the data is read at the end of setting of all points, the points cannot be set independently.

* If the amp power was turned off during setting, the setting points cannot be memorized. (The previous settings are retained.)

* The confirmation beep sounds only when the motor was connected. If the LED does not go off but blinks rapidly, setting was not performed normally. Repeat setting from "Neutral point setting". Continuous rapid blink Assembly / Adjustment 15 2CHANNEL SYSTEMST.D/RPOWERST.TRIMTH.TRIM 2POK-2.4G Functions Steering Trim Steering neutral adjustments can be made by moving the Steering trim knob to the left or right. Racers Tip When you install a servo, always check to be sure the servo is at its neutral position. Adjust the servo horn hole position and linkage so both are parallel. When a servo saver is used, place it as close to center position as possible. Be sure the steering trim on the transmitter is at the neutral position. Trim Operation And Maximum Travel Changing the trim can affect the overall settings. When adjustments are made with the trims, recheck your installation for maximum travel. (Steering D/R). When Trim usage is extreme If it takes most of your trim movement to get a servo to the neutral position, reposition the servo horn or servo saver on the servo and inspect your linkage installation. Steering Trim ST.TRIM Direct Servo Saver Horn Servo Saver 90 90 Parallel Throttle Trim Throttle neutral adjustments can be made moving the throttle trim to the left or right. Racers Tip When using an electronic speed control, set the throttle trim to neutral and make adjustments to the speed control. On a gas powered model, set the trim to neutral and adjust the linkage to the point where the carburetor is fully closed in accordance with the engine instruction manual. Trim Operation and Travel Trim adjustments will affect the overall servo travel. Check the brake side (backward) movement when changes are made. When trim movement is extreme If you use most of the trim movement to get the servo to the neutral position , recenter the servo horn closer to the neutral position and inspect your throttle linkage. 16 2POK Functions Throttle Trim TH.TRIM Carburetor Fully Closed

(Drum Type)

(Slide Type) 2CHANNEL SYSTEMSERVO REVST.D/RNRST.TH.POWERST.TRIMTH.TRIM2CHANNEL SYSTEMSERVO REVST.D/RNRST.TH.POWERST.TRIM Steering Dual Rates Use this function to adjust the steering travel of your model. If the model understeers (push) while cornering, add steering by turning C,W of the D/R button. When the model oversteers (loose), take away steering by turning C,C,W of the D/R button. Steering Dual Rates ST.D/R

 WARNING

 Be sure that the steering linkage does not bind or come in contact with any suspension parts or arms. If unreasonable force is applied to the servo, the servo may be damaged and result in loss of control. Steering Servo Reversing This function reverses the rotation direction of the Steering servo. Steering Servo Reverse When the trim position deviates from the center, the deviation will be on the opposite side when the servo is reversed. Nor: Normal Rev: Reverse SERVO REV N R ST. Throttle Servo Reversing This function reverses the rotation direction of the throttle servo. Throttle Servo Reversing (REV-CH2) Throttle Servo Reverse When the trim position deviates from the center, the deviation will be on the opposite side when the servo is reversed. Nor: Normal Rev: Reverse SERVO REV N R TH. 2POK Functions 17 2CHANNEL SYSTEMSERVO REVST.D/RNRST.TH.POWERST.TRIMTH.TRIM2CHANNEL SYSTEMSERVO REVST.D/RNRST.TH.POWERST.TRIMTH.TRIM2CHANNEL SYSTEMSERVO REVST.D/RNRST.TH.POWERST.TRIMTH.TRIM MC230CR/MC330CR CANCELLING THE REVERSE FUNCTION The amp reverse function can be cancelled by the following method so that the model can be used even in races that prohibit reverse running. (Brake operation only) MC230CR / MC330CR

(Pushbutton switch operation)

(Power switch) 1 Reverse function cancellation While pressing the pushbutton switch, ON set the power switch to ON.

* When desired, you can enable the cancelled reverse function by repeating the operation shown at the left.

(The reverse function is switched alternately.) BRAKE/REVERSE OPERATING INSTRUCTIONS Operation can be switched to reverse operation by returning the throttle trigger (or throttle stick) from the brake position to the neutral position. PROTECTION CIRCUIT OPERATION The following protection circuits are built into the MC230CR / MC330CR. When a protection circuit operates, remove the cause before operating the model again. Overcurrent protection Heat protector Low voltage operation When an overcurrent flows due to an output short circuit, etc., the overcurrent protection circuit automatically limits the current to protect the FET. Remove the cause of the short circuit, etc. before operating the model again. When abnormal heating of the FET due to an overload, etc. is detected, the heat protector operates so that the speed is gradually reduced. When the FET temperature drops, the heat protector automatically resets. However, remove the cause of the overheating before operating the model again. When the Nicd battery voltage drops, this function limits the motor output current and ensures steering operation. After the speed drops, immediately recover the vehicle. CHECKER LED DISPLAY The amp operates linearly in proportion to the amount of forward, reverse, and brake operation. The amp operating state can be checked with the checker LED as shown below. Operation Checker LED display Amp power ON

(Reverse operation set) Single blink

(Single confirmation beep)

(Only brake operation set) Double blink

(Two confirmation beeps) High point Forward Neutral point Reverse

/brake Brake MAX point Off On Off On Off

*Becomes brighter nearer the high point.

*Becomes brighter nearer the brake MAX point.

(Amp power left on alarm) When the transmitter power was turned off first. Blinks. (Confirmation beep also sounds.)

*Not used with PCM receivers.

*When the transmitter is OFF, this function is not performed in environments such that the servo operates erroneously.

* Confirmation beep only sounds when the motor was connected. 18 2POK Functions Reference

*Specifications and ratings are subject to change without prior notice. Ratings Communication method:

One-way operation system Maximum operating range:

80m (Optimum condition) For safety:

F/S (Throttle), ID (About 4 billion ways of pair identifications) Transmitter T2POK

(FHSS system, wheel type, 2 channels) Transmitting frequency:

2.4GHz band Power requirement:

(Dry cell battery) Penlight x 4(6V) Current drain:

100mA or less Transmission antenna:

1/2 di-pole (Built-in) Receiver R203GF:

(FHSS/S-FHSS system, 3 channels) Power requirement:

4.8V 7.4V Rechargeable battery Size:

26x39x10mm (excluding a projection part) Weight:

8g Servo S3003

(Standard servo) Power requirement:

6V (common with receiver) Current drain:

8mA (at 6V / Idle) Output torque:

4.1kg-cm (57in.-oz.) at 6V Operating speed:

0.19sec/60 degree at 6V Size:

40.4x19.8x36mm (1.59x0.78x1.42in.) Weight:

37.2g (1.31oz.) Servo S3050

(Standard digital servo) Power requirement:

6V (common with receiver) Current drain:

8mA (at 6V / Idle) Output torque:

6.5kg-cm (90.3oz.-in.) at 6V Operating speed:

0.16sec/60 degree at 6V Size:

40.0x20.0x38.1mm (1.57x0.79x1.50in.) Weight:

49g (1.72oz.) E.S.C. MC230CR / MC330CR

(Electronic speed control) Operating system:

Forward, reverse, and brake operations are all linear. Power requirement:

Nicd battery 6-7 cells (7.2 to 8.4V) PWM frequency:

1.5kHz (fixed) Setting:

One-touch input by pushbutton switch. Set data is saved to built-in EEPROM. Current capacity (FET rating):

Forward=90A/200A, reverse=45A/100A Size:

27.1x33.3x12.8mm (1.07x1.31x0.50in.)

(excluding protruding parts) Silicon cord gauge size:

AWG16/AWG14 equivalent Weight:

44/45g (1.55/1.59oz.)

(including connectors and switches) BEC voltage:

6.0V NOTE: Futaba FHSS system, T2POK transmitter and R203GF receiver, does not work with cur-

rent Futaba FASST system. Please use T2POK and R203GF in pairs. Futaba FASST system 2POK Functions and FHSS system are not compatible each other. 19 Troubleshooting If your system fails to operate or you experience a short range problem or erratic control, check the table below for possible causes. If after you have followed the suggestions listed the problem is not corrected, return the system to our service department for inspection and repair.

(Item Check) Transmitter Battery Change the batteries. Dead battery Batteries inserted incorrectly. polarity markings Faulty contact contact Dirty contacts Reload the batteries in accordance with the Check to see if the contacts are bent and not making good Clean the contacts and check for corrosion. Receiver Battery Dead battery Wrong polarity Replace or recharge Check connections Antenna Near other wiring Was antenna cut Is the antenna installed correctly Move away from wiring Request repair Refer to the receiver installation. Monitor LED Check the LED of the receiver. Refer to the "How to link the transmitter and the receiver". Connector connections Wiring incorrect Loose connections Insert all connectors firmly Push the connector in firmly Linkage Binding or loose Is movement stiff Adjust the linkage in model Adjust linkage in model Motor (Electric powered) Noise problems Install capacitors on motor 20 Reference Error Displays Error Displays Low Battery When the LED starts blinking, replace the batteries immediately. LED light:

 WARNING

 When a low battery alarm is generated, cease operation immediately and retrieve the model. If the battery goes dead while in operation, you will lose control. ST.TRIM TH.TRIM 2CHANNEL SYSTEM SERVO REV POWER ST.D/R N R ST. TH. When requesting repair Before requesting repair, read this instruction again and recheck your system. Should the problems continue, request as follows.

(Information needed for repair) Describe the problem in as much detail as possible and send the letter along with the system in question. Symptom (Including the conditions and when the problem occurred) R/C System (Send transmitter, receiver and servos) Model (Type of model, brand name and model number or kit name) Detailed packing list (Make a list of all items sent in for repair) Your name, address and telephone number.

(Warranty) Read the Warranty card. When requesting warranty service, send the card or some type of dated proof of purchase. Hobby Services (U.S. only) 3002 N. Apollo Drive, Suite 1 Champaign, IL 61822 U.S.A. Phone: (217) 398-0007 www.hobbyservices.com FUTABA CORPORATION Phone: +81 475 32 6982, Facsimile: +81 475 32 6983 1080 Yabutsuka, Chosei-mura, Chosei-gun, Chiba-ken, 299-4395, Japan FUTABA CORPORATION 2011, 03 (1) Reference 21