FCC ID: AZPTMFH-24G Radio Control

TM-FH 2.4GHz Module Specification Frequency Band: 2400MHz ~ 2483.5MHz Frequency Range: 2403.25MHz ~ 2447.5MHz Interval of Channel: 750kHz Channel: 60 channels Module Type: FHSS Communication Scheme: Single Communication RF Output Power: 15dBm Antenna: 1/2 Print Pattern type antenna, 2.0dBi Power Requirement: 12V Current: 60mA Outer Dimensions: 37.2(W)x20.4(D)x58.8(H) mm Weight: Approx. 40g

3 Walk away from the model while simultaneously operating the controls. Have an assistant stand by the model to confirm that all controls are completely and correctly operational. You should be able to walk approximately 30-50 paces from the model without losing control. 4 If the servos jitter or move inadvertently, there may be a problem. We would strongly suggest you do not fly until the source of the difficulty has been determined. Look for loose servo connections or binding pushrods. Also, be certain that the battery has been fully charged.

 WARNING

Please make sure that you do not push and hold the F/

S, Range switch when flying as this reduces the power output of the transmitter and reduces the overall range of your transmitter. Other precautions When utilizing the trainer function of the transmitter as an instructor, please do not switch to the student's control unit until the RF is active after turning the transmitter on. Failure to adhere to this procedure may result in a malfunction. Please refer to the table below for the LED status of the receiver's condition. Green Off Solid Receiving signals Blink Receiving signals but ID is unmatched Alternate blink Unrecoverable failure (EEPROM, etc.) Red Solid No signal reception Off Off Status Battery F/S function The TM-FH transmitter module and R2006GS receiver also provides you with a second safety system, the Battery F/S

(failsafe). When the airborne voltage drops below 3.8V, the battery failsafe function moves the throttle to a pre-determined F/S position. If this happens, you should land immediately!

If you need to increase the throttle for your landing approach, you may temporarily reset the failsafe function by moving the throttle stick to the predetermined position, after which you'll have about 30 seconds of throttle control before the battery function reactivates.

* Please note: It is suggested that you utilize a 4-cell NiCD or NiMH receiver battery pack as it allows the effective use of the battery F/S function. Additionally, we do not suggest using dry cell batteries for the receiver pack as they may cause difficulties. Range Check the Radio It is extremely important to range check your models prior to each flying session. This enables you to ensure that everything is functioning as it should and to obtain maximum enjoyment from your time flying. The TM-FH transmitter module incorporates a system that reduces its power output and allows you to perform such a range check. 1 Turn on the transmitter. 2 After the radio frequency link has been established

, press and hold the "F/S, Range" switch located on the rear of the TM-FH transmitter module. The RF output display of the transmitter disappears, and the buzzer of the transmitter rings. the radio frequency power has been reduced to allow for the range check.

* Note: Do not press and hold the "F/S, Range" switch prior to turning on the transmitter. This will alter the status of the F/S settings as noted previously. In order to avoid this situation, please wait for a short time after turning on the transmitter to activate the low power setting on for range checking. Repair Service (in U.S.A.) If any difficulties are encountered while setting up or operating your TM-FH transmitter module and R2006GS receiver, please consult this instruction manual first. For further assistance you may also refer to your hobby dealer, or contact the Futaba Service Center at the web site, fax or telephone number below:

www.futaba-rc.com, www.2.4gigahertz.com Fax (217) 398-7721, Tel (217) 398-8970 (option 2) If you are unable to resolve the issue, pack the system in its original container with a note enclosed and a thorough, accurate description of the difficulty. Include the following in your note:

Symptoms (Including when the problem occurred) System (transmitter, Receiver, Servos and model numbers) Model (Model name) Model numbers and quantity Your Name, Address and Telephone number Send the respective items to the authorized Futaba Service Center address below:

Futaba Service Center 3002 N Apollo Drive Suite 1 Champaign, IL 61822 FCC Information To assure continued FCC compliance:

(1) Any changes or modifications not expressly approved by the grantee of this device could void the user's authority to operate the equipment. FCC Label Compliance Statement:

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Copyright 2011. No part of this manual may be reproduced in any form without prior permission. The contents of this manual are subject to change without prior notice. While this manual has been carefully written, there may be inadvertent errors or omissions. Please contact our service center if you feel that any corrections or clarifications should be made. FUTABA CORPORATION 1080 Yabutsuka, Chosei-mura, Chosei-gun, Chiba-ken, 299-4395, Japan Phone: +81 475 32 6982, Facsimile: +81 475 32 6983 FUTABA CORPORATION 2011, 06 (1)

- 4 -

1M23N25802 S-FHSS Air System TM-FH RF Module R2006GS Receiver and Instruction Manual Applicable systems:

T9C, T9Zwc2, T10C Important: The 2.4GHz band offers different characteristics than that of the conventional 50MHz and 72MHz. As such, we strongly encourage you to read this manual carefully prior to utilizing the TM-

FH and R2006GS S-FHSS system. Thank you for purchasing the TM-FH 2.4GHz transmitter module and R2006GS receiver. This system is designed for use only with the Futaba transmitters indicated elsewhere in this manual. In order to use the TM-

FH transmitter module, you will need to carefully remove the existing transmitter module and replace it with the TM-FH transmitter module. The receiver R2006GS, as the model number indicates, is capable of controlling models up to six channels. Please note: The installation of the R2006GS differs slightly from that of a typical receiver. Please pay special attention to the information contained within this manual in order to have a pleasant flying experience. Note:

Futaba S-FHSS system and FASST system are not compatible each other. Features:

2.4GHz Spread Spectrum radio communication system. Exclusive ID code to avoid interference from other S-FHSS systems. Fail Safe (F/S) function (for throttle channel)-F/S, Battery F/S Dual antenna diversity (R2006GS) Usage Precautions:

1) Prior to utilizing any radio control system, it is strongly recommended that you read and abide by the Safety Code created by the Academy of Model Aeronautics as well as any site specific rules and regulations that might exist. Doing so will greatly increase your enjoyment of the hobby. 2) In order to maintain complete control of your aircraft it is important that it remains visible at all times. Flying behind large objects such as build-

ings, grain bins, etc. is not suggested. Doing so may result in the reduc-

tion of the quality of the radio frequency link to the model. 3) Please do not grasp the transmitter module's antenna during flight. Do-

ing so may degrade the quality of the radio frequency transmission. Contents and Technical Specifications Your 2.4GHz system includes the following components:

R2006GS Receiver Easy Link Swich Mini screwdriver Range Check Swich Specifications:

TM-FH RF Module-

Communication system: one-way communication Antenna: 1/2 wavelength di-pole Current consumption: 150mA maximum Setting switch for Fail Safe (F/S) setting and range check R2006GS Receiver-

Dual antenna diversity Power requirement: 4.8V or 7.4V battery or regulated out-

put from ESC, etc. (*1) F/S and Battery F/S function for throttle channel (channel three) Size: 1.70 x 0.98 x 0.35 in. (43.1 x 25.0 x 8.8 mm) Weight: 0.30 oz. (8.5g)

(*1) Be sure that when using ESC's regulated output the capacity of the ESC must meet your usage condition. Never use dry cell batteries for the R2006GS receiver as this may cause difficulties with the receiver's operation. TM-FH RF Module Special Markings;

Pay special attention to the safety at the parts of this manual that are indicated by the following marks.

[Symbol] ; Prohibited ; Mandatory Mark Meaning Procedures which may lead to a dangerous condition and cause death or serious injury to the user if not carried out properly. Procedures which may lead to a dangerous condition or cause death or serious injury to the user if not carried out properly, or procedures where the probability of superficial injury or physical damage is high. Procedures where the possibility of serious injury to the user is small, but there is a danger of injury, or physical damage, if not carried out properly.

- 1 -

Installing the TM-FH Module and R2006GS Receiver Attachment of the Module you install or replace the module.

 CAUTION

Be sure to turn off the power of the transmitter before 1Ensure that the transmitter is set to the PPM (pulse position modulation) mode. Please consult the respective owner's manual for your particular transmitter for information on how to do so. 2While it is unlikely that the existing transmitter antenna will interfere with the radio frequency transmission of the TM-FH, we suggest removing it from the transmitter if possible as a precaution. 3 Next, with the transmitter's power off, remove the existing transmitter module and install the TM-

FH module with care so that the connector pins of the transmitter won't be damaged. Do not bent the connector pins. Antenna of TM-FH 1 As with all radio frequency transmissions, the strongest area of signal transmission is from the sides of the TM-FH transmitter module's antenna. As such, the antenna should not be pointed directly at the model. If your flying style creates this situation, easily move the antenna to correct this situation. 2 Please do not grasp the transmitter's antenna during flight. Doing so may degrade the quality of the RF transmission to the model. Easy Link Each TM-FH transmitter module has an individually assigned unique ID code. In order to start operation, the receiver must be linked to the respective TM-FH's ID code. Once the linking is done, the ID code is stored in the receiver and the re-linking is not necessary unless the receiver is to be used with a different TM-FH module. Additionally, it is important to note that this TM-FH and R2006GS receiver set has already been linked by the factory. Should you wish to re-link them, or if you have purchased a separate receiver and would like to link it to this TM-FH, please adhere to the following procedure.

 WARNING

After the linking is done, please cycle receiver power and check if the receiver to be linked is really under the con-

trol by the transmitter to be linked.

Do not perform the linking procedure with motor's main wire is connected or the engine is operating as it may result in serious injury. 1 After the TM-FH module has been installed into the transmitter, using the aforementioned steps, turn on the transmitter. The RF output confirmation display of the transmitter is confirmed. If not, power down the transmitter and turn it on once again. turned on. 2When the transmitter is turned on, the receiver is 3 With the receiver on, press and hold the Easy Link button, located on the receiver, for approximately two seconds and release it. Then the receiver starts linking procedure. When the linking process has been completed, the LED on the receiver will change to a solid green and the linking is established. Receiver Installation You will note that the R2006GS differs in appearance from the standard Futaba receiver. The R2006GS incorporates two separate antennas into its design which enables it to receive the radio frequency transmission at two different locations. Futaba's dual antenna diversity, or DAD, then seamlessly selects the best signal reception between these antennas to ensure that there is no loss of signal.

*Must be kept as straight as possible. Antenna Coaxial cable To obtain the best results from the R2006GS receiver, please refer to the following instructions and precautions:

1 Install the receiver in the aircraft using the same methodology as you would handle a standard receiver. That is, make sure that you wrap the receiver in foam rubber or other such material to make it less susceptible to vibration, etc. maximum effective range from your model. straight as possible. This will allow you to obtain the 2 Ensure that the two receiver antennas are kept as 3If possible, please make sure that the two antennas are placed at 90 degrees to each other. Please note:

This is not a critical figure, however, the most important thing is to keep the antennas away from each other as much as possible. 4 If your model includes metal conductive items which may impact the receiver's ability to clearly receive the radio frequency signal, we suggest mounting the receiver so that the receiver antennas exit both sides of the model. This will allow the best radio frequency signal condition at any flying attitude. 5 Ensure that the antennas are at least 1/2" away from any conductive materials such as metal and carbon. Please note: this is not applicable to the coaxial portion of the antenna. It is important, however, to not bend the coax, or antenna in a tight radius. 6If the fuselage is made of conductive materials such as metal and carbon, the antennas part MUST be positioned so that they exit the fuselage. Additionally, do not attach the antenna itself to this fuselage.

* For example, there are many types of gliders which use carbon fu-

selage. When install the receiver into such models, it is imperative that the antenna precautions are adhered to strictly.

 WARNING

Be very careful when handling the receiver antennas. Repeated bending and flexing of the antennas or exces-

sive force could weaken or compromise the internal antenna connections.

Keep the antennas away from the motor, ESC, and other noise sources as much as possible. Antenna Antenna The main purpose of the Illustration demonstrates how the antenna should be placed. For actual installation the receiver must be wrapped with a sponge or placed with floating material to protect it from vibration.

* The receiver contains delicate electronic parts and should be pro-

tected from vibration, shock and temperature extremes.

* The receiver is not impervious to damage from moisture. If moisture should enter the receiver, intermittent operation or failure may result. To prevent this from occurring, we suggest wrapping the receiver in a plastic bag or similar protective covering. This will also protect the receiver from any fuel or exhaust residue which can work its way into the fuselage. F/S (Fail Safe) mode setting The F/S is suggested for use as it offers a safety factor when controlling your models. It is also possible to cancel the F/

S operation if you do not wish to use it. As for F/S, only the throttle servo (3ch) works. F/S mode The F/S mode sets responses in case of loss of signal or low Rx battery. (ch3 only) HOLD : In case of loss of signal, the HOLD mode holds the throttle servo in its last commanded position. (The RF output confirmation display of the transmitter usually lights.) F/S : In case of loss of signal, the F/S mode holds the throttle servo in its last commanded position for one second and then moves the throttle servo to a predetermined position. (The RF display blinks once at power supply ON.) B.F/S (Battery Fail Safe) : When the airborne battery voltage drops below approximately 3.8V, the B.F/S mode moves the throttle servo to a predetermined position. In case of loss of signal, the B.F/S mode holds the throttle servo in its last commanded position for one second and then moves the throttle servo to a predetermined position. (The RF display blinks twice at power supply ON . ) Setting of the F/S (Failsafe) mode HOLD Initial state F/S B.F/S POWER Turn on the transmitter. Press and hold the RANGE button. The F/S mode is selectable one by one at this operation. F/S position setting procedure As mentioned at "Easy Link", the R2006GS starts linking process by press the Easy Link button more than two seconds. Meanwhile, when linking is done, the R2006GS stores 3ch(Throttle) position as the F/S position automatically. By this way, the receiver renew the F/S data for current 3ch position. Prior to doing so, ensure that the F/S is active. If not, please follow the Setting of the F/S Mode procedure as noted previously. meter of the transmitter, turn on the transmitter. S position(slow), and the receiver located within one 1 With the transmitter's throttle stick in the desired F/

2 With the transmitter on, turn on the receiver. Press 3Turn off the transmitter in five seconds. The throttle and hold the Easy Link button, located on the receiver, servo should move to the pre-determined F/S position. for approximately two second.

- 2 -

- 3 -

Futaba Corporation Radio Control FCC ID. : AZPTMFH-24G EUT Internal Photos Figure 3 Internal View (Removed Covers) Figure 4 General Appearance (RF Module, Front View) Futaba Corporation Radio Control FCC ID. : AZPTMFH-24G Figure 5 General Appearance (RF Module, Front View) Figure 6 General Appearance (RF Module, Back View)

Futaba Corporation Radio Control FCC ID. : AZPTMFH-24G EUT External Photos Figure 1 General Appearance (Front & Side View) Figure 2 General Appearance (Back & Side View)

Futaba Corporation Radio Control FCC ID. : AZPTMFH-24G FCC ID Label Location

Label Placement Location FCC Label Placement Location

FCC Label Format

Futaba FUTABA corporation Engineering Section 1 Radio Control Equipment Group 1080 Yabutsuka chosei-son chousei-gun chiba 299-4395 JAPAN Authorization Letter Date: Mar.10, 2011 Compliance Certification Services Certification Division 561F Monterey Road Morgan Hill, CA 95037 To whom it may concern:

We, the undersigned, hereby authorize AUDIX Technology Corporation, to act on our behalf in all manners relating to application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by AUDIX Technology Corporation on our behalf shall have the same effect as acts of our own. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). In authorizing AUDIX Technology Corporation as our agent, we still recognize that we are responsible to:

a) comply with the relevant provisions of the certification program;

b) make all necessary arrangements for the conduct of the evaluation, including provision for examining documentation and access to all areas, records

(including internal audit reports) and personnel for the purposes of evaluation

(e.g. testing, inspection, assessment, surveillance, reassessment) and resolution of complaints;

Cc) make claims regarding certification only in respect of the scope for which certification has been. granted;

d) do not use our product certification in such a manner as to bring the Certification Division into disrepute and not make any statement regarding our product certification which the Certification Division may consider misleading or unauthorized;

Futaba FUTABA corporation Engineering Section 1 Radio Control Equipment Group 1080 Yabutsuka chosei-son chousei-gun chiba 299-4395 JAPAN e) upon suspension or cancellation of certification, discontinue use of all advertising matter that contains any reference thereto and return any certification documents as required by the Certification Division;

f) use certification only to indicate the products are certified as being in conformity with specified standards;

g) endeavor to ensure that no certificate or report nor any part thereof is used ina misleading manner;

h) ensure that any reference to our product certification in communication media such as documents, brochures or advertising, complies with the requirements of the Certification Division;

i) keep a record of all complaints made known to the us relating to the products compliance with requirements of the relevant standard and to make these records available to the Certification Division when requested;

j) take appropriate action with respect to such complaints and any deficiencies found in products or services that affect compliance with the requirements for certification;

k) document the actions taken. This authorization is valid until further written notice from the applicant. Sincerely, Kazunori Fujita Radio Control Equipment Group Manager Futaba Corporation

uojesodiog eqeyny dnoisy Juswdinby josu0D olpey Jebeueyw dnois ewin4 wounzey hf romm bor AJQIBOUIS uoneol|dde sit} JO} JUeIS OY} Jo a}ep ay} BJOJaq apew 9q JOU |JIM UONe}UsUNOOp BulAuedwoooe |je pue uoNnedijdde siuj jo aunsojosip Sainy eu] JO JGP'Q UOI}D9eS oO} JUeNSJNd yeu} spue}sIapUN jyUeOI|Iddy oUL

"SJOUJACWOD S}I 0} S}YoUEq peyNsnfun epiAosd pue jUeoI|\dde au} Oo} jnNJWeY eq Aew sjeayeu aseu} JO ainsojosip oqnd sy oljqnd au} 0} pesesjed Ajlsewo}sno yOU UOleWJOjU! Aiejyelidoid pue sjolo9s apes uleJuoO sjele}ewW aAoge eUL weibelq ayewsyuIS

(uolesodo Jo Ajoau}) uondUoseg jeuoweisdO wejbelq yoo|g JeuoHouny @

MO|eq PeUly}NO se uoeojdde siy} BuilAuedwoooe uol}eWUOjU! jo JUSLU}eeJ] [eUSPYyUOS jsenbel Aqeaiay aM Ssainy S,UOISSILILWUOD 84} JO GGPr'Q Pue /GP'O UOI}OEeS 0} }UeNSINY

[UBLUE)JUSS) 92-HAWLdZV -di 994 jo UOHedYIPIED Joy UHL ddy Bulpiebas ysanboy Ayyjenuspyu0g :yoefqns UOISIAIG UOMeNnjeAy pue uojezuoyny UOISSILULUOD SUOIESIUNWUOD je1ape4 LLOd GL unr :ayeq Ayyenuapyuoy 10) jsanbey oN

Applicant/Grantee FCC ID:

The radio elements of the modular transmitter must have their own shielding. The physical crystal and tuning capacitors may be located extemal to the shielded radio elements. The modular transmitter must have buffered modulation/data inputs (if such inputs are provided) to ensure that the module will comply with Part 15 requirements under conditions of The modular transmitter must have its own power supply regulation. The modular transmitter must comply with the antenna and transmission system requirements of Sections 15.203, 15.204(b) and 15.204(c). The antenna must either be permanently attached or employ a unique antenna coupler (at all connections between the module and the antenna, including the cable). The professional installation provision of Section 15.203 is not applicable to modules but can apply to limited modular approvals under paragraph (b) of this section. The modular transmitter must be tested in a stand-alone configuration, i.e., the module must not be inside another device during testing for compliance with Part 15 requirements. Unless the transmitter module will be battery powered, it must comply with the AC line conducted requirements found in Section 15.207. AC or DC power lines and data input/output lines connected to the module must not contain ferrites, unless they will be marketed with the module (see Section 15.27(a)). The length of these lines shall be the length typical of actual use or, if that length is unknown, at least 10 centimeters to. insure that there is no coupling between the case of the module and supporting

|] | Request for Limited Modular Ap proval

| Requirements Single Modular Approval Requirements excessive data rates or over-modulation. EUT Conditions Comply (Y/N) Yes, This TMFH module has its own shielding. However, it is Limited Modular Approval and be integrated Radio controller manufactured by Futaba co. The TMFH modular includes MSP430 which is able to buffer modulation/data inputs. The modular includes regulator IC which provides 5.0 and 3.3 Volt. The TMFH module includes U-FL type connector. U-FL type connector is unique type connector so it is difficult to change antenna. This TMFH module could be tested in a stand-alone configuration and given DC power via power lines. Y equipment. Any accessories, peripherals, or support equipment connected to the module during testing shall be unmodified and commercially available

(see Section 15.31(i)). The modular transmitter must be equipped with either a permanently affixed label or must be capable of electronically displaying its FCC identification number.

(A) Ifusing a permanently affixed label, the modular transmitter must be labeled with its own FCC identification number, and, if the FCC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: Contains Transmitter Module FCC ID: XYZMODEL! or Contains FCC ID:

XYZMODEL1. Any similar wording that expresses the same meaning may be used. The Grantee may either provide such a label, an example of which must be included in the application for equipment authorization, or, must provide adequate instructions along with the module which explain this requirement. In the latter case, a copy of these instructions must be included in the application for equipment authorization.

(B) If the modular transmitter uses an electronic display of the FCC identification number, the information must be readily accessible and visible on the modular transmitter or on the device in which it is installed. If the module is installed inside another device, then the outside of the device into which the module is installed must display a label referring to the enclosed module. This exterior label can use wording such as the following:

Contains FCC certified transmitter module(s). Any similar wording that expresses the same meaning may be used. The user manual must include instructions on how to access the electronic display. A copy of these instructions must be included in the application for equipment authorization. The modular transmitter must comply with any specific rules or operating requirements that ordinarily apply to a complete transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements. A copy of these instructions must be included in the application for equipment authorization. The label indicated FCC ID is attached on the case of the modular. Y The modular has adequate instructions and a copy of these instructions is included in the application. Y The modular transmitter must comply with any applicable RF exposure requirements in its final configuration. A limited modular approval may be granted for single or split modular transmitters that do not comply with all of the above requirements, e.g., shielding, minimum signaling amplitude, buffered modulation/data inputs, or power supply regulation, if the manufacturer can demonstrate by alternative means in the application for equipment authorization that the modular transmitter meets all the applicable Part 15 requirements under the operating conditions in which the transmitter will be used. Limited modular approval also may be granted in those instances where compliance with RF exposure rules is demonstrated only for particular product configurations. The applicant for certification must state how control of the end product into which the module will be installed will be maintained such that full compliance of the end product is always ensured. Yes, the modular transmitter complies with applicable RF exposure. Sincerely Yours, Kazunori Fujita Group Manager Radio Control Equipment Group Futaba Corporation