Mini 3G Router i11 Quick Start Guide Package Contents:
One i11 Mini 3G Router One USB data Cable One Power Adapter One installation Guide If any of above items are damaged or missing, please contact with your distributor. Panel Layout System LED Name Fuction Red The Router is power on Red in quickly flashing Green Green in quickly flashing Blue in slowly flashing Bule in quickly flashing transmission data via WiFi LAN/WAN cable is connected but there is no data being transmitted or received LAN/WAN cable is connected but there is data being transmitted or received 3G or WAN is not connected 3G or WAN is connected Link Status LED 3G Port The port is used to connect 3G modem. 3G/DHCP Switch This switch is used to switch operation mode of the Router between 3G and DHCP. Power This port is used to connect the provided power adapter. LAN/WAN This LAN/WAN port works as WAN in Dynamic IP/Static IP/PPPoE mode and as LAN in 3G mode. As LAN, it connects the Router to the local PC; as WAN, it enables you connect DSL/cable Modem, or Ethernet. RESET With the Router powered on, use a pin to press and hold the RESET button (about 8 seconds) until the LED becomes turn off, and then release the button and wait the Router reboot to its default settings. Quick install i11 Hardware installation 1. powered by USB cable connect the Router and the computer using a USB cable like below, the Router can powerd on automatically. 2. Powered by USB adapter You also can use USB adapter to supply for the Rouer, follow step 1, 2, 3 to connect them. NotesThe output of the adapter should between 5V 750mAh and 5V, 2A. Connecting the Router Plug the power plug in the electrical wall socket. The Router will start to work automatically.
[Windows XP]
Click the "Start/Control Panel", double-click "Network Connections", in the "Wireless Network Connection" right click and select "View Available Wireless Networks", Highlight the SSID of Router (here is 3G ROUTER) and cick Connect to add to the network. On the right shows "connected that indicates successfully connected to the 3G router.
[Winodws 7]
icon, When 3G modem installed, the lower right corner of the computer there is a click the icon, and will see a pop-up network list, select "3G ROUTER" the wireless network, and then double-click it to connect, when the screen appears "connected". Now lets open the IE Explorer( Iphone for Safari),type the default IP:192.168.100.1 in the Address bar, then the Usernameadmin, Password: adminNo bold wordsclick OK into the management interface:
Setting 3G Router the router support 3G, Static IP, Dynamic IP, PPPoE, click Basic Settings on the left side of WEB page, so you should first choose Routers operating mode, the default mode is 3G dialup. 1. 3G Dial-UP The default mode for the Router is 3G Dial-up. It already integrates many ISP parameters over the world, and customers can choose the ones they want accroding to 3G Modems, there is different parameters in different country. For the foreigners, if a 3G Modem is not compatible with our Router, we can realize it from remote online control, to make your 3G modems comply our router. Return to Status > Running Status, check 3G Dialup says connected, if its connected, you should be able to access Internet via 3G. Other cases:
If 3G Dialup says disconnect, it means no 3G connection, maybe your 3G Modem is not attached to the router, you can check the Modems VID/PID in 3G Modem(VID/PID), if the VID/PID is Unrecognized, either the routers USB port is bad or the 3G Modem is bad. If 3G Dialup says connecting, please wait, it means that the router is dialing now, please wait for a moment, after 20 seconds, refresh the page until 3G Dialup says connected, if the status connecting, please wait has shown for a long time, please check as follows:
1. Check the 3G Router has supported your 3G Modem;
2. Check your 3G Modem can work well when directly connected to your computer. 3. Check your settings are correct. 2. PPPoE If you have applied ADSL to realize Dial-up service, you should choose this type. Under this condition, you should fill in both the User Name and Password that the ISP supplied. Please note that there fields are case-sensitive. Open the router WEB interface, click on the "Basic Settings> Internet access mode", select PPPoE, enter the broadband Internet account and password, click "OK" to save the settings, Return to the "System Status> running", if PPPoE dial-up display "Connected", said that it has successfully connected to the broadband network. 3. Staic IP Network operators to provide you with an Internet IP address, select Static IP, static IP mode, the router's WAN port to use as an ETH port. In the "Basic Settings> Internet access mode" select the Static IP mode, then enter your ISP's IP address, subnet mask, default gateway, DNS and other related parameters can be. 4. Dynamic IP Dynamic IP is widely used in hotels and restaurants and other public places, the Router can connect via dynamic IP mode to hotels and other public access network resources, the first, hotel of the network cable to the ETH interface to the router, then through the following two methods to router switch to dynamic IP mode. 1) hard-switching: the switch router 3G/DHCP pull to the DHCP file. 2) Soft Switch: turn on the router interface, click on the "Basic Settings> Internet access mode", select the dynamic IP, and then click "OK" to save the settings. Wireless Encryption Selecting Wireless Settings>Wireless Encription, will enable you to configure wireless security for your wireless network to protect your data from intruders. The Router prodivers three types: WEP, WPA-PSK, WPA2-PSK. The security options are different operation mode, it is recommended to use WPA-PSK security mode.