FCC ID: M5VC30044XB Prox Readers T11 Multi Tech, SMB T11 and T12 Multi Tech

Gallagher T11 Reader Installation Note T11 MIFARE Reader, Black: C300410 T11 MIFARE Reader, White: C300411 T11 Multi Tech Reader, Black: C300430 T11 Multi Tech Reader, White: C300431 High Sec T11 Reader, Black: C305410 High Sec T11 Reader, White: C305411 High Sec T11 Reader, Multi Tech, Black: C305430 High Sec T11 Reader, Multi Tech, White: C305431 Page 1 3E4719 Gallagher T11 Reader | Edition 10 | March 2023 Copyright Gallagher Group Limited Disclaimer This document gives certain information about products and/or services provided by Gallagher Group Limited or its related companies (referred to as "Gallagher Group"). The information is indicative only and is subject to change without notice meaning it may be out of date at any given time. Although every commercially reasonable effort has been taken to ensure the quality and accuracy of the information, Gallagher Group makes no representation as to its accuracy or completeness and it should not be relied on as such. To the extent permitted by law, all express or implied, or other representations or warranties in relation to the information are expressly excluded. Neither Gallagher Group nor any of its directors, employees or other representatives shall be responsible for any loss that you may incur, either directly or indirectly, arising from any use or decisions based on the information provided. Except where stated otherwise, the information is subject to copyright owned by Gallagher Group and you may not sell it without permission. Gallagher Group is the owner of all trademarks reproduced in this information. All trademarks which are not the property of Gallagher Group, are acknowledged. Copyright Gallagher Group Ltd 2023. All rights reserved. Contents 1 2 3 4 5 6 7 8 9 Introduction ..................................................................................................................................... 3 Before you begin .............................................................................................................................. 4 Distance between readers ............................................................................................................... 6 Installation ....................................................................................................................................... 7 LED indications ................................................................................................................................. 9 Accessories ...................................................................................................................................... 9 Technical specifications .................................................................................................................. 10 Approvals and Compliance Standards............................................................................................ 10 Mounting dimensions .................................................................................................................... 12 Page 2 3E4719 Gallagher T11 Reader | Edition 10 | March 2023 Copyright Gallagher Group Limited 1 Introduction The Gallagher T11 Reader is a smart card and Bluetooth low energy technology reader. It can be installed as either an entry reader or exit reader. It can be mounted on a vertical, rectangular 50 mm x 75 mm (2" x 3") flush box with mounting holes spaced at a nominal 85 mm (3.25"). The reader sends information to the Gallagher Controller and acts upon information sent from the Gallagher Controller. The reader itself does not make any access decisions. The reader is available in eight variants. The supported technologies and compatibility for each variant is shown in the table below. Reader Variant Product Codes Card Technologies Supported T11 MIFARE Reader C300410 C300411 T11 Multi Tech Reader C300430 C300431 High Sec T11 Reader C305410 C305411 C305430 C305431 High Sec T11 Reader, Multi Tech ISO 14443A MIFARE DESFire EV1/EV2*/EV3**, MIFARE Plus, and MIFARE Classic cards ISO 14443A MIFARE DESFire EV1/EV2*/EV3**, MIFARE Plus, MIFARE Classic, and 125 KHz cards ISO 14443A PIV, PIV-I, CAC, TWIC, MIFARE DESFire EV1/EV2*/EV3**, MIFARE Plus, and MIFARE Classic cards ISO 14443A PIV, PIV-I, CAC, TWIC, MIFARE DESFire EV1/EV2*/EV3**, MIFARE Plus, MIFARE Classic, and 125 KHz cards NFC Access for Android Supported From Bluetooth Access Supported From HBUS Comms Supported From Cardax IV Comms Supported From vEL7.80 HBUS only None vEL7.00 vEL1.02 vEL7.80 HBUS only vEL7.60 HBUS only vEL7.00 vEL1.02***

vEL7.80 HBUS only vEL7.80 HBUS only None vEL7.10 None None vEL7.10 None

* MIFARE DESFire EV2 is supported from vEL7.70.

** MIFARE DESFire EV3 is supported from vEL8.30.1458 (or later).

*** Gallagher strongly recommends against using dual technology 125/MIFARE cards with Multi Tech Readers for sites running pre-Command Centre v7.00 software. From Command Centre v7.00, a site may specify which technology a Multi Tech Reader should read off a dual technology card. Page 3 3E4719 Gallagher T11 Reader | Edition 10 | March 2023 Copyright Gallagher Group Limited 2 Before you begin 2.1 Shipment contents Check the shipment contains the following items:

1 x Gallagher T11 Reader facia assembly 1 x Gallagher T11 Reader bezel 1 x M3 Torx Post Security screw 2 x 6-32 UNC Phillips drive fixing screws 4 x 25 mm No.6 self tapping, pan head, Phillips drive fixing screws 4 x 40 mm No.6 self tapping, pan head, Phillips drive fixing screws 2.2 Power supply The Gallagher T11 Reader is designed to operate over a supply voltage range of 9 - 16 Vdc measured at the reader terminals. The operating current draw is dependant on the supply voltage at the reader. For a MIFARE reader, at 13.6 Vdc the current draw is 50 mA (idle). During credential read, beeper and LED activity, the current will momentarily reach 77 mA (maximum). For a Multi Tech reader, at 13.6 Vdc the current draw is 80 mA (idle) and will momentarily reach 142 mA (maximum). The power source should be linear or a good quality switched-mode power supply. The performance of the reader may be affected by a low quality, noisy power supply. 2.3 Cabling The Gallagher T11 Reader requires a minimum cable size of 4 core 24 AWG (0.2 mm2) stranded security cable. This cable allows the transmission of data (2 wires) and power (2 wires). When using a single cable to carry both power supply and data, both the power supply voltage drop and data requirements must be considered. Although the reader is specified to operate at 9 Vdc, for good engineering design it is recommended that the voltage at the reader should be approximately 12 Vdc. HBUS cabling topology The HBUS communications protocol is based on the RS485 standard and allows the reader to communicate over a distance of up to 500 m (1640 ft). The cabling between HBUS devices should be done in a "daisy chain" topology, (i.e. A "T" or

"Star" topology should not be used between devices). Should "Star" or "Home-Run" wiring be required, the HBUS 4H/8H Modules and the HBUS Door Module allow multiple HBUS devices to be individually wired to the one physical location. The end devices on the HBUS cable should be terminated using 120 ohms resistance. To terminate the Gallagher Controller 6000, connect the supplied on-board termination jumpers to the Controller. To terminate a reader, connect the orange (termination) wire to the green

(HBUS A) wire. Termination is already included at the HBUS Module, (i.e. each HBUS port is permanently terminated at the module). Page 4 3E4719 Gallagher T11 Reader | Edition 10 | March 2023 Copyright Gallagher Group Limited HBUS Device

"T" or "Star" circuits are not permitted between HBUS devices HBUS Device Terminate HBUS Device HBUS Device HBUS Device RS485 1 Controller 6000 Connect the on-board termination jumper HBUS Device

"T" or "Star" circuits are not permitted between HBUS devices HBUS Device Terminate HBUS Device RS485 1 Controller 6000 HBUS Device Remove the on-board termination jumper HBUS Device Terminate HBUS Device Terminate HBUS Device Controller 6000 H1 H5 H4 H8 HBUS Module HBUS Device HBUS Device Terminate HBUS Device HBUS Device Terminate Terminate Page 5 3E4719 Gallagher T11 Reader | Edition 10 | March 2023 Copyright Gallagher Group Limited Cable distance Cable type Cable format*

CAT 5e or better**

BELDEN 9842**

(shielded) SEC472 SEC4142 C303900/

C303901 Gallagher HBUS Cable 4 twisted pair each 2 x 0.2 mm2 (24 AWG) 2 twisted pair each 2 x 0.2 mm2 (24 AWG) 4 x 0.2 mm2 Not twisted pairs (24 AWG) 4 x 0.4 mm2 Not twisted pairs (21 AWG) 2 Twisted pair each 2 x 0.4 mm2 (21 AWG, Data) and 2 x 0.75 mm2 Not Twisted Pair

(~18 AWG, Power) HBUS single reader connected using data only in a single cable Cardax IV single reader connected using data only in a single cable***

HBUS/Cardax IV single reader connected using power and data in a single cable****

500 m (1640 ft) 200 m (650 ft) 100 m (330 ft) 500 m (1640 ft) 200 m (650 ft) 100 m (330 ft) 400 m (1310 ft) 200 m (650 ft) 100 m (330 ft) 400 m (1310 ft) 200 m (650 ft) 150 m (500 ft) 500 m (1640 ft) 200 m (650 ft) 450 m (1490 ft)

* The matching of wire sizes to equivalent wire gauges are only approximate.

** Recommended cable types for optimal HBUS RS485 performance.

*** Not applicable for PIV or Bluetooth enabled reader installations.

**** Tested with 13.6V at start of cable. Notes:

Shielded cable may reduce the obtainable cable length. Shielded cable should be grounded at the Controller end only. If other cable types are used, operating distances and performance may be reduced depending on the cable quality. HBUS allows up to 20 readers to be connected to a single cable. Each reader requires at least 9 Vdc to function correctly. The cable length and the number of readers connected will have an impact on the voltage at each reader. 3 Distance between readers The distance separating any two proximity readers must not be less than 200 mm (8 in) in all directions. When mounting a proximity reader on an internal wall, check that any reader fixed to the other side of the wall is not less than 200 mm (8 in) away. 200 mm 200 mm Page 6 3E4719 Gallagher T11 Reader | Edition 10 | March 2023 Copyright Gallagher Group Limited 4 Installation ATTENTION: This equipment contains components that can be damaged by electrostatic discharge. Ensure both you and the equipment are earthed before beginning any servicing. The Gallagher T11 Reader is designed to be mounted on vertically orientated electrical flush (gang) boxes, or any solid flat surface. However installation on metal surfaces, particularly those with a large surface area will reduce read range. The extent to which the range is reduced will depend upon the type of metal surface. Note: Consideration should be given to the installation environment when using Bluetooth enabled readers, as the read range may be reduced. The recommended mounting height for the reader is 1.1 m (3.6 ft) from the floor level to the centre of the reader device. However this may vary in some countries and you should check local regulations for variations to this height. 1. Ensure the building cable has been run out through the flush box. If you are not mounting to a flush box, use the reader bezel as a guide to drill all five holes. Drill the 13 mm (1/2 inch) diameter centre hole (this is the centre hole for which the building cable will exit the mounting surface) and the four fixing holes. 2. 3. Run the building cabling out through the centre hole and through the reader bezel. Secure the bezel to the flush box using the two 6-32 UNC screws provided. It is important the reader bezel is flush with and tight against the mounting surface. If you are not mounting to a flush box, secure the bezel to the mounting surface using the four fixing screws provided. Note: It is strongly recommended that you use the screws provided. If an alternative screw is used, the head must be no larger nor deeper than that of the screw provided. Note: Ensure the centre hole allows the cable to run freely out through the mounting surface, so that the reader facia can clip into the bezel. 6-32 UNC screw Bezel Building cable 6-32 UNC screw 4. Connect the reader tail extending from the facia assembly to the building cable. Connect the wires for the appropriate reader you wish to interface, either an HBUS Reader or a Cardax IV Reader, as shown in the following diagrams. Page 7 3E4719 Gallagher T11 Reader | Edition 10 | March 2023 Copyright Gallagher Group Limited Note: PIV and Bluetooth enabled readers must be connected as HBUS Readers. PIV readers connect to the Gallagher High Sec Controller 6000 (C305101) only. An HBUS Reader connects to a Gallagher Controller 6000, Gallagher 4H/8H Module (attached to a Controller 6000) or a Gallagher HBUS Door Module (connected to a Controller 6000). A Cardax IV Reader connects to a Gallagher Controller 6000, Gallagher 4R/8R Module (attached to a Controller 6000) or a Gallagher GBUS Universal Reader Interface (Gallagher GBUS URI). HBUS Reader connection:

HBUS Reader terminated:

r e d a e R S U B H Red Positive Black Negative HBUS Termination Orange Green HBUS A Brown HBUS B White CDXIV TX Blue CDXIV RX r e d a e R S U B H Red Positive Black Negative HBUS Termination Orange Green HBUS A Brown HBUS B White CDXIV TX Blue CDXIV RX Note: To terminate an HBUS Reader, connect the Orange (HBUS Termination) wire to the Green

(HBUS A) wire. Cardax IV Reader connection:

r e d a e R V I x a d r a C Red Positive Black Negative HBUS Termination Orange Green HBUS A Brown HBUS B White CDXIV TX Blue CDXIV RX 5. 6. Fit the facia assembly into the bezel by clipping the small lip, into the top of the bezel and holding the top, press the bottom of the facia assembly down into the bezel. Insert the M3 Torx Post Security screw (using a T10 Torx Post Security screwdriver) through the hole at the bottom of the bezel to secure the facia assembly. Note: The Torx Post Security screw needs only to be lightly tightened. Reader tail Building cable Facia Connection Fit screw to secure facia to bezel Page 8 3E4719 Gallagher T11 Reader | Edition 10 | March 2023 Copyright Gallagher Group Limited 7. 8. Removal of the facia assembly is a simple reversal of these steps. Configure the reader in Command Centre. If the reader is connected as an HBUS Reader, refer to the topic "Configuring HBUS Devices" in the Command Centre Configuration Client Online Help. If the reader is connected as a Cardax IV Reader, refer to the topic "Creating Readers" in the Command Centre Configuration Client Online Help. 5 LED indications LED (squiggle) HBUS indication 3 Flash (Amber) No communications with the Controller. 2 Flash (Amber) Communications with the Controller, but reader is not configured. 1 Flash (Amber) Configured to a Controller, but reader is not assigned to a door or elevator car. On (Green or Red) Fully configured and functioning normally. Green = Access mode is Free Red = Access mode is Secure Flashes Green Access has been granted. Flashes Red Access has been denied. Flashes (Blue) Reading and validating a PIV card. Reading a Gallagher mobile credential. LED (squiggle) Cardax IV indication 3 Flash (Amber) No communications with the Controller. On (Green or Red) Fully configured and functioning normally. Green = Access mode is Free Red = Access mode is Secure Flashes Green Access has been granted. Flashes Red Access has been denied. 6 Accessories Accessory T11 Dress Plate, Black, Pk 10 T11 Bezel, Black, Pk 10 T11 Bezel, White, Pk 10 T11 Bezel, Silver, Pk 10 T11 Bezel, Gold, Pk 10 T11 Spacer, Black, Pk 10 T11 Spacer, White, Pk 10 T11/T12 Protective Cover Spacer T11/T12 Protective Cover Product Code C300321 C300284 C300285 C300286 C300287 C300302 C300303 C300311 C300271 Page 9 3E4719 Gallagher T11 Reader | Edition 10 | March 2023 Copyright Gallagher Group Limited 7 Technical specifications Routine maintenance:

Not applicable for this reader Cleaning:

Voltage:

Current4:

This reader should only be cleaned with a clean, lint free, damp cloth 9 Vdc - 16 Vdc at 9 Vdc at 13.6 Vdc MIFARE Reader Multi Tech Reader Idle1 70 mA 50 mA Maximum2 Idle1 Maximum2 115 mA 77 mA 106 mA 80 mA 176 mA 142 mA Temperature range:

-35 C to +70 C Note: Direct sunlight may increase the internal reader temperature above the ambient temperature level Humidity:

0 - 95% non-condensing3 Environmental protection:

Impact rating:

Unit dimensions:

IP68 IK07 Height 115 mm (4.5") Width 70 mm (2.8") Depth 12 mm (0.5") Maximum number of readers on one HBUS cable:

20 1 The reader is idle. 2 Maximum reader current during credential read. 3 Gallagher T Series readers are UL humidity tested and certified to 85% and have been independently verified to 95%. 4 Reader currents verified by UL are provided in the document "3E2793 Gallagher Command Centre UL Configuration Requirements". Note: The current values stated above have been reported using the default configuration for a reader in Command Centre. Changing the configuration may vary the current value. 8 Approvals and Compliance Standards This symbol on the product or its packaging indicates that this product must not be disposed of with other waste. Instead, it is your responsibility to dispose of your waste equipment by handing it over to a designated collection point for the recycling of waste electrical and electronic equipment. The separate collection and recycling of your waste equipment at the time of disposal will help conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment. For more information about where you can drop off your waste equipment for recycling, please contact your local city recycling office or the dealer from whom you purchased the product. This product complies with the environmental regulations for the Restriction of Hazardous Substances in electrical and electronic equipment (RoHS). The RoHS directive prohibits the use of electronic equipment containing certain hazardous substances in the European Union. FCC This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: Changes or modifications not expressly approved by Gallagher Limited could void the user's authority to operate this equipment. Page 10 3E4719 Gallagher T11 Reader | Edition 10 | March 2023 Copyright Gallagher Group Limited Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Industry Canada Industrie Canada This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. UL Installations Please refer to the document "3E2793 Gallagher Command Centre UL Configuration Requirements" for a guide to configuring the Gallagher system to the appropriate UL Standard. Installers must ensure these instructions are followed to ensure the installed system is UL compliant. AS/NZS IEC 60839.11.1:2019 Grade 4, Class II HVIN FCC ID IC ID C300410 T11 MIFARE Reader, Black C300411 T11 MIFARE Reader, White C305410 High Sec T11 Reader, Black C305411 High Sec T11 Reader, White C300410- T11 MIFARE Reader, Black C300411- T11 MIFARE Reader, White C300430 T11 Multi Tech Reader, Black C300431 T11 Multi Tech Reader, White C305430 High Sec T11 Reader, Multi Tech, Black C305431 High Sec T11 Reader, Multi Tech, White C300430- T11 Multi Tech Reader, Black C300431- T11 Multi Tech Reader, White C500430 SMB T11 Reader, Black C500431 SMB T11 Reader, White C500430- SMB T11 Reader, Black C500431- SMB T11 Reader, White M5VC30042XA 7369A-C30022X M5VC30042XB 7369A-C30022XB M5VC30044XA 7369A-C30024X M5VC30044XB 7369A-C30024XB M5VC30044XA M5VC30044XB US - Equipment: com, burg and acc reader CA - Equipment: com, burg reader Page 11 3E4719 Gallagher T11 Reader | Edition 10 | March 2023 Copyright Gallagher Group Limited 9 Mounting dimensions

9 8 1

. m m 8 4

6 2 1

. m m 2 3 13 mm (1/2") diameter hole for cable MIFARE Card read area

7 5 1

. m m 0 4

3 5 4

. m m 5 1 1 22.5 mm

(0.89") 40 mm (1.57") 70 mm (2.76") IMPORTANT This picture is not to scale, therefore use the measurements provided. 125 Card read area Page 12 3E4719 Gallagher T11 Reader | Edition 10 | March 2023 Copyright Gallagher Group Limited

Gallagher T12 Reader Installa on Note T12 MIFARE Reader, Black: C300420 T12 MIFARE Reader, White: C300421 T12 Mul Tech Reader, Black: C300440 T12 Mul Tech Reader, White: C300441 High Sec T12 Reader, Black: C305420 High Sec T12 Reader, White: C305421 T12 Mul Tech Reader, Black Not Po ed: C300440-01 3E4720 Gallagher T12 Reader | Edi on 12 | May 2023 Copyright Gallagher Group Limited Page 1 Disclaimer This document gives certain informa on about products and/or services provided by Gallagher Group Limited or its related companies (referred to as "Gallagher Group"). The informa on is indica ve only and is subject to change without no ce meaning it may be out of date at any given me. Although every commercially reasonable e ort has been taken to ensure the quality and accuracy of the informa on, Gallagher Group makes no representa on as to its accuracy or completeness and it should not be relied on as such. To the extent permi ed by law, all express or implied, or other representa ons or warran es in rela on to the informa on are expressly excluded. Neither Gallagher Group nor any of its directors, employees or other representa ves shall be responsible for any loss that you may incur, either directly or indirectly, arising from any use or decisions based on the informa on provided. Except where stated otherwise, the informa on is subject to copyright owned by Gallagher Group and you may not sell it without permission. Gallagher Group is the owner of all trademarks reproduced in this informa on. All trademarks which are not the property of Gallagher Group, are acknowledged. Copyright Gallagher Group Ltd 2023. All rights reserved. 3E4720 Gallagher T12 Reader | Edi on 12 | May 2023 Copyright Gallagher Group Limited Page 2 Contents 1 2 3 4 5 6 7 8 9 Introduc on ..................................................................................................................................... 3 Before you begin .............................................................................................................................. 4 Distance between readers ............................................................................................................... 6 Installa on ....................................................................................................................................... 7 LED indica ons ................................................................................................................................. 9 Accessories ...................................................................................................................................... 9 Technical speci ca ons .................................................................................................................. 10 Approvals and Compliance Standards............................................................................................ 10 Moun ng dimensions .................................................................................................................... 12 1 Introduc on The Gallagher T12 Reader is a smart card and Bluetooth low energy technology reader. It can be installed as either an entry reader or exit reader. It can be mounted on a BS 4662 Bri sh Standard square ush box. The reader sends informa on to the Gallagher Controller and acts upon informa on sent from the Gallagher Controller. The reader itself does not make any access decisions. The reader is available in four variants. The supported technologies and compa bility for each variant is shown below. Reader Variant Product Codes Card Technologies Supported T12 MIFARE Reader C300420 C300421 T12 Mul Tech Reader High Sec T12 Reader C300440 C300441 C300440-01 C305420 C305421 ISO 14443A MIFARE DESFire EV1/EV2*/EV3**, MIFARE Plus, and MIFARE Classic cards ISO 14443A MIFARE DESFire EV1/EV2*/EV3**, MIFARE Plus, MIFARE Classic, and 125 KHz cards ISO 14443A PIV, PIV-I, CAC, TWIC, MIFARE DESFire EV1/EV2*/EV3**, MIFARE Plus, and MIFARE Classic cards NFC Access for Android Supported From Bluetooth Access Supported From HBUS Comms Supported From Cardax IV Comms Supported From vEL7.80 HBUS only None vEL7.00 vEL1.02 vEL7.80 HBUS only vEL7.60 HBUS only vEL7.00 vEL1.02***

vEL7.80 HBUS only None vEL7.10 None

* MIFARE DESFire EV2 is supported from vEL7.70.

** MIFARE DESFire EV3 is supported from vEL8.30.1458 (or later).

*** Gallagher strongly recommends against using dual technology 125/MIFARE cards with Mul Tech Readers for sites running pre-Command Centre v7.00 so ware. From Command Centre v7.00, a site may specify which technology a Mul Tech Reader should read o a dual technology card. 3E4720 Gallagher T12 Reader | Edi on 12 | May 2023 Copyright Gallagher Group Limited Page 3 2 Before you begin 2.1 Shipment contents Check the shipment contains the following items:

1 x Gallagher T12 Reader facia assembly 1 x Gallagher T12 Reader bezel 1 x M3 Torx Post Security screw 2 x M3.5 Phillips drive xing screws 4 x 25 mm No.6 self tapping, pan head, Phillips drive xing screws 4 x 40 mm No.6 self tapping, pan head, Phillips drive xing screws 2.2 Power supply The Gallagher T12 Reader is designed to operate at a supply voltage of 13.6Vdc measured at the reader terminals. The opera ng current draw is dependant on the supply voltage at the reader. For a MIFARE reader, at 13.6 Vdc the current draw is 50 mA (idle). During creden al read, beeper and LED ac vity, the current will momentarily reach 77 mA (maximum). For a Mul Tech reader, at 13.6 Vdc the current draw is 80 mA (idle) and will momentarily reach 142 mA (maximum). The power source should be linear or a good quality switched-mode power supply. The performance of the reader may be a ected by a low quality, noisy power supply. 2.3 Cabling The Gallagher T12 Reader requires a minimum cable size of 4 core 24 AWG (0.2 mm2) stranded security cable. This cable allows the transmission of data (2 wires) and power (2 wires). When using a single cable to carry both power supply and data, both the power supply voltage drop and data requirements must be considered. For good engineering design it is recommended that the voltage at the reader should be approximately 12 Vdc. HBUS cabling topology The HBUS communica ons protocol is based on the RS485 standard and allows the reader to communicate over a distance of up to 500 m (1640 ). The cabling between HBUS devices should be done in a "daisy chain" topology, (i.e. A "T" or

"Star" topology should not be used between devices). Should "Star" or "Home-Run" wiring be required, the HBUS 4H/8H Modules and the HBUS Door Module allow mul ple HBUS devices to be individually wired to the one physical loca on. The end devices on the HBUS cable should be terminated using 120 ohms resistance. To terminate the Gallagher Controller 6000, connect the supplied on-board termina on jumpers to the Controller. To terminate a reader, connect the orange (termina on) wire to the green

(HBUS A) wire. Termina on is already included at the HBUS Module, (i.e. each HBUS port is permanently terminated at the module). 3E4720 Gallagher T12 Reader | Edi on 12 | May 2023 Copyright Gallagher Group Limited Page 4 HBUS Device

"T" or "Star" circuits are not permi ed between HBUS devices HBUS Device Terminate HBUS Device HBUS Device HBUS Device RS485 1 Controller 6000 Connect the on-board termina on jumper HBUS Device

"T" or "Star" circuits are not permi ed between HBUS devices HBUS Device Terminate HBUS Device RS485 1 Controller 6000 HBUS Device Remove the on-board termina on jumper HBUS Device Terminate HBUS Device Terminate HBUS Device Controller 6000 H1 H5 H4 H8 HBUS Module HBUS Device HBUS Device Terminate HBUS Device HBUS Device Terminate Terminate 3E4720 Gallagher T12 Reader | Edi on 12 | May 2023 Copyright Gallagher Group Limited Page 5 Cable distance Cable type Cable format*

CAT 5e or be er**

BELDEN 9842**

(shielded) SEC472 SEC4142 C303900/

C303901 Gallagher HBUS Cable 4 twisted pair each 2 x 0.2 mm2 (24 AWG) 2 twisted pair each 2 x 0.2 mm2 (24 AWG) 4 x 0.2 mm2 Not twisted pairs (24 AWG) 4 x 0.4 mm2 Not twisted pairs (21 AWG) 2 Twisted pair each 2 x 0.4 mm2 (21 AWG, Data) and 2 x 0.75 mm2 Not Twisted Pair (~18 AWG, Power) HBUS single reader connected using data only in a single cable Cardax IV single reader connected using data only in a single cable***

HBUS/Cardax IV single reader connected using power and data in a single cable****

500 m (1640 ) 200 m (650 ) 100 m (330 ) 500 m (1640 ) 200 m (650 ) 100 m (330 ) 400 m (1310 ) 200 m (650 ) 100 m (330 ) 400 m (1310 ) 200 m (650 ) 150 m (500 ) 500 m (1640 ) 200 m (650 ) 450 m (1490 )

* The matching of wire sizes to equivalent wire gauges are only approximate.

** Recommended cable types for op mal HBUS RS485 performance.

*** Not applicable for Bluetooth enabled reader installa ons.

**** Tested with 13.6V at start of cable. Notes:

Shielded cable may reduce the obtainable cable length. Shielded cable should be grounded at the Controller end only. If other cable types are used, opera ng distances and performance may be reduced depending on the cable quality. HBUS allows up to 20 readers to be connected to a single cable. Each reader requires at least 9 Vdc to func on correctly. The cable length and the number of readers connected will have an impact on the voltage at each reader. 3 Distance between readers The distance separa ng any two proximity readers must not be less than 200 mm (8 in) in all direc ons. When moun ng a proximity reader on an internal wall, check that any reader xed to the other side of the wall is not less than 200 mm (8 in) away. 200 mm 200 mm 3E4720 Gallagher T12 Reader | Edi on 12 | May 2023 Copyright Gallagher Group Limited Page 6 4 Installa on ATTENTION: This equipment contains components that can be damaged by electrosta c discharge. Ensure both you and the equipment are earthed before beginning any servicing. The Gallagher T12 Reader is designed to be mounted on a standard Bri sh electrical ush box, or any solid at surface. However installa on on metal surfaces, par cularly those with a large surface area will reduce read range. The extent to which the range is reduced will depend upon the type of metal surface. Note: Considera on should be given to the installa on environment when using Bluetooth enabled readers, as the read range may be reduced. The recommended moun ng height for the reader is 1.1 m (3.6 ) from the oor level to the centre of the reader device. However this may vary in some countries and you should check local regula ons for varia ons to this height. 1. 2. 3. Ensure the building cable has been run out through the ush box. If you are not moun ng to a ush box, use the reader bezel as a guide to drill all ve holes. Drill the 13 mm (1/2 inch) diameter centre hole (this is the centre hole for which the building cable will exit the moun ng surface) and the four xing holes. Run the building cabling out through the centre hole and through the reader bezel. Secure the bezel to the ush box using the two M3.5 screws provided. It is important the bezel of the reader is ush with and ght against the moun ng surface. If you are not moun ng to a ush box, secure the bezel to the moun ng surface using the four xing screws provided. Note: It is strongly recommended that you use the screws provided. If an alterna ve screw is used, the head must be no larger nor deeper than that of the screw provided. Note: Ensure the centre hole allows the cable to run freely out through the moun ng surface, so that the reader facia can clip into the bezel. Bezel Building cable M3.5 screw M3.5 screw 4. Connect the reader tail extending from the facia assembly to the building cable. Connect the wires for the appropriate reader you wish to interface, either an HBUS Reader or a Cardax IV Reader, as shown in the following diagrams. Notes:

Bluetooth enabled readers must be connected as HBUS Readers. Gallagher High Sec readers must be connected as HBUS Readers. Gallagher High Sec reader connect to the Gallagher High Sec Controller 6000 (C305101) only. 3E4720 Gallagher T12 Reader | Edi on 12 | May 2023 Copyright Gallagher Group Limited Page 7 An HBUS Reader connects to a Gallagher Controller 6000, Gallagher 4H/8H Module (a ached to a Controller 6000) or a Gallagher HBUS Door Module (connected to a Controller 6000). A Cardax IV Reader connects to a Gallagher Controller 6000, Gallagher 4R/8R Module (a ached to a Controller 6000) or a Gallagher GBUS Universal Reader Interface (Gallagher GBUS URI). HBUS Reader connec on:

HBUS Reader terminated:

r e d a e R S U B H Red Posi ve Nega ve Black HBUS Termina on Orange Green HBUS A Brown HBUS B White CDXIV TX Blue CDXIV RX r e d a e R S U B H Red Posi ve Nega ve Black HBUS Termina on Orange Green HBUS A Brown HBUS B White CDXIV TX Blue CDXIV RX Note: To terminate an HBUS Reader, connect the Orange (HBUS Termina on) wire to the Green

(HBUS A) wire. Cardax IV Reader connec on:

r e d a e R V I x a d r a C Red Posi ve Nega ve Black HBUS Termina on Orange Green HBUS A Brown HBUS B White CDXIV TX Blue CDXIV RX Fit the facia assembly into the bezel by clipping the small lip, into the top of the bezel and holding the top, press the bo om of the facia assembly down into the bezel. Insert the M3 Torx Post Security screw (using a T10 Torx Post Security screwdriver) through the hole at the bo om of the bezel to secure the facia assembly. Note: The Torx Post Security screw needs only to be lightly ghtened. Facia Bezel Building cable Reader tail Connec on Fit screw to secure facia to bezel Removal of the facia assembly is a simple reversal of these steps. Con gure the reader in Command Centre. If the reader is connected as an HBUS Reader, refer to the topic "Con guring HBUS Devices" in the Command Centre Con gura on Client Online Help. If the reader is connected as a Cardax IV Reader, refer to the topic "Crea ng Readers" in the Command Centre Con gura on Client Online Help. 5. 6. 7. 8. 3E4720 Gallagher T12 Reader | Edi on 12 | May 2023 Copyright Gallagher Group Limited Page 8 5 LED indica ons LED (squiggle) HBUS indica on 4 Rapid Flashes (Red) The controller that the reader is connected to is currently upgrading. 3 Flash (Amber) No communica ons with the Controller. 2 Flash (Amber) Communica ons with the Controller, but reader is not con gured. 1 Flash (Amber) Con gured to a Controller, but reader is not assigned to a door or elevator car. On (Green or Red) Fully con gured and func oning normally. Green = Access mode is Free Red = Access mode is Secure Flashes Green Access has been granted. Flashes Red Access has been denied. Flashes (Blue) Reading a Gallagher mobile creden al. LED (squiggle) Cardax IV indica on 3 Flash (Amber) No communica ons with the Controller. On (Green or Red) Fully con gured and func oning normally. Green = Access mode is Free Red = Access mode is Secure Flashes Green Access has been granted. Flashes Red Access has been denied. 6 Accessories Accessory T12 Dress Plate, Black, Pk 10 T12 Bezel, Black, Pk 10 T12 Bezel, White, Pk 10 T12 Bezel, Silver, Pk 10 T12 Bezel, Gold, Pk 10 T12 Spacer, Black, Pk 10 T12 Spacer, White, Pk 10 T11/T12 Protec ve Cover Spacer T11/T12 Protec ve Cover Product Code C300322 C300288 C300289 C300290 C300291 C300304 C300305 C300311 C300271 3E4720 Gallagher T12 Reader | Edi on 12 | May 2023 Copyright Gallagher Group Limited Page 9 7 Technical speci ca ons Rou ne maintenance:

Not applicable for this reader Cleaning:

Voltage:

Current4:

Temperature range:

This reader should only be cleaned with a clean, lint free, damp cloth 13.6Vdc MIFARE Reader Mul Tech Reader Idle1 50 mA Maximum2 77 mA Idle1 80 mA Maximum2 142 mA

-35 C to +70 C Note: Direct sunlight may increase the internal reader temperature above the ambient temperature level Humidity:

0 - 95% non-condensing3 Environmental protec on:

Impact ra ng:

Unit dimensions:

IP685 IK076 Height 86 mm (3.4") Width 86 mm (3.4") Depth 12 mm (0.5") Maximum number of readers on one HBUS cable:

20 1 The reader is idle. 2 Maximum reader current during creden al read. 3 Gallagher T Series readers are UL humidity tested and cer ed to 85% and have been independently veri ed to 95%. 4 Reader currents veri ed by UL are provided in the document "3E2793 Gallagher Command Centre UL Con gura on Requirements". Note: The current values stated above have been reported using the default con gura on for a reader in Command Centre. Changing the con gura on may vary the current value. 5 The unpo ed variant (C300440-01) does not have any environmental protec on. 6 The unpo ed variant (C300440-01) does not have any impact ra ngs. 8 Approvals and Compliance Standards This symbol on the product or its packaging indicates that this product must not be disposed of with other waste. Instead, it is your responsibility to dispose of your waste equipment by handing it over to a designated collec on point for the recycling of waste electrical and electronic equipment. The separate collec on and recycling of your waste equipment at the me of disposal will help conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment. For more informa on about where you can drop o your waste equipment for recycling, please contact your local city recycling o ce or the dealer from whom you purchased the product. This product complies with the environmental regula ons for the Restric on of Hazardous Substances in electrical and electronic equipment (RoHS). The RoHS direc ve prohibits the use of electronic equipment containing certain hazardous substances in the European Union. 3E4720 Gallagher T12 Reader | Edi on 12 | May 2023 Copyright Gallagher Group Limited Page 10 FCC This device complies with part 15 of the FCC Rules. Opera on is subject to the following two condi ons: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired opera on. Note: Changes or modi ca ons not expressly approved by Gallagher Limited could void the user's authority to operate this equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protec on against harmful interference in a residen al installa on. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruc ons, may cause harmful interference to radio communica ons. However, there is no guarantee that interference will not occur in a par cular installa on. If this equipment does cause harmful interference to radio or television recep on, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separa on between the equipment and receiver. Connect the equipment into an outlet on a circuit di erent from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Industry Canada Industrie Canada This device complies with Industry Canada licence-exempt RSS standard(s). Opera on is subject to the following two condi ons: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired opera on of the device. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploita on est autorise aux deux condi ons suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'u lisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est suscep ble d'en comprome re le fonc onnement. UL Installa ons Please refer to the document "3E2793 Gallagher Command Centre UL Con gura on Requirements" for a guide to con guring the Gallagher system to the appropriate UL Standard. Installers must ensure these instruc ons are followed to ensure the installed system is UL compliant. AS/NZS IEC 60839.11.1:2019 Grade 4, Class II HVIN FCC ID IC ID C300420 T12 MIFARE Reader, Black C300421 T12 MIFARE Reader, White C305420 High Sec T12 Reader, Black C305421 High Sec T12 Reader, White C300420- T12 MIFARE Reader, Black C300421- T12 MIFARE Reader, White C300440 T12 Mul Tech Reader, Black C300441 T12 Mul Tech Reader, White C305440 High Sec T12 Mul Tech Reader, Black C305441 High Sec T12 Mul Tech Reader, White C300440-01 T12 Mul Tech Reader, Black Not Po ed C300440- T12 Mul Tech Reader, Black C300441- T12 Mul Tech Reader, White C300440-01- T12 Mul Tech Reader, Black Not Po ed M5VC30042XA 7369A-C30022X M5VC30042XB 7369A-C30022XB M5VC30044XA 7369A-C30024X M5VC30044XB 7369A-C30024XB US - Equipment: com, burg and acc reader CA - Equipment: com, burg reader 3E4720 Gallagher T12 Reader | Edi on 12 | May 2023 Copyright Gallagher Group Limited Page 11 9 Moun ng dimensions 30 mm (1.18") 10 mm (0.39")

4 1 1

. m m 9 2

1

m m 6 2 13 mm (1/2") diameter hole for cable

9 3 3

. m m 6 8

8 8 0

. m m 3 2 2

. 40 mm (1.57") 35 mm (1.38") 25 mm (1") 86 mm (3.39") IMPORTANT This picture is not to scale, therefore use the measurements provided. 3E4720 Gallagher T12 Reader | Edi on 12 | May 2023 Copyright Gallagher Group Limited Page 12

300430 - 111 Multi Tech Reader, Black FCC ID: MSVC30044XB 1C:7369A-C30024XB Contains FCC 1D: QOQ-GN220P 10:5123A-GM220P 15mm SIN:1234567890 ES {GALLAGHER

(300431 - 111 Multi Tech Reader, White FCC ID: MSVC30044XB 10:7369A-C30024XB Contains FCC 1D: Q0Q-GM220P 1C:5123A - GM220P SIN:1234567890 ESS @Gdusoner a 142 Multi Tech Reader, Black ID: MSVC30044XB _IC:7369A --C30024XB contain a ie Q0Q-GM220P IC:5123A -GM220P FI va 0 Be QGAUAGHER 6300441 - 112 Multi Tech Reader, White FCC ID: MBVC30044XB 1C:7369A-C30024XB Contains FCC 1D: Q00-GM220P 16:5123A-GM220P S/N:1234567890 Ee QGALAGHER 6500430 - SMB 111 Reader Black Gracie FCC ID: MSVC30044XB 1C:7369A-C30024XB Contains FCC 1D: QOQ-GM220P 1C:5123A - GMi220P SIN=1234567890 [I UNINNTINIOUAINIUIOUULUU

(500431 - SMB 111 Reader White e@dusonte FCC ID: MSVC30044XB 1C:7369A-C30024XB Contains FCC 1D: Q0Q-GM220P 1C:5123A-GM220P SIN-1234567890 [I UVINIVDUINIONAVNOULOO UT

(300440 -01- 112 Mulli Tech Reader, Black Not Potted FCC ID: MSVC30044XB 1C:7369A-C30024XB Contains FCC ID: Q0Q-GM220P 1C:5123A-GM220P SIN:123456789 ie 46.5 mm Material: Thermafilm 21940 UL approved gloss wnite sell-aqhesive polyester T11 & T12 Multi Tech, SMB T11 Product Labels axvz0e 69EL:91 yoe|g sapeay Yaa]

6300430 - 111 Multi FCC ID: MBC30044 Contains FCC 1D: 00

$IN:1234567890 SAFETY US- Equipment: 00 eeu CA~ Equipment: COND

=| BP8861 Refer to document S4715 and rating information, Mad T11 Mifare, Multi Tech, SMB T11 - Product ID and Location oll 20- 112 Mifare R MSVC30042XB No:123456789 Refer to document and rating informat and Locati

Federal Communication Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21048 May 04, 2023 TO WHOM IT MAY CONCERN Pursuant to Paragraphs 0.457 and 0.459 of the Commissions Rules (47 C.F.R.) and Section 552(b)(4) of the Freedom of Information Act, Gallagher Group Ltd requests confidentiality for the following products:

FCC ID Number Product Title/Model M5VC30044XB T11 Multi Tech Reader, T11 SMB Reader and T12 Multi Tech Reader For the products stated above, we request that the following information be held confidential:

1) Electrical Schematics of the Circuitry 2) Block Diagram 3) Operational Description No other items submitted as part of the equipment authorization filing process are deemed confidential. The above exhibits contain Gallagher Group Ltd trade secrets and proprietary information that could be of benefit to our competitors regarding the design of our Readers. This material is not customarily available to the general public and we request that it be withheld from public inspection. If you have any questions, please feel free to contact me at the address shown below. Sincerely, Menardo Lazaro Technical Leader - Compliance GALLAGHER GROUP LIMITED 181 Kahikatea Drive, Hamilton 3206, New Zealand. Private Bag 3026, Hamilton 3240, New Zealand. TEL +64 7 838 9800 FAX +64 7 838 9801 EMAIL info@gallagher.com WEB www.gallagher.com

CKC Certification Services, LLC CB: US0103; NB/AB: 0976 5046 Sierra Pines Drive Mariposa, CA 95338 Phone: 1 800-500-4EMC (4362) Fax: 209-787-5568 Email: tcbadmin@ckc.com APP-FCC-A Applicant Attestation Applicant Information Company Name:

Contact Name:

Contact Title:

Company Address:

Telephone No:

Facsimile No:

Email Address:

Gallagher Group Ltd. Tony Smith Hardware Development Manager 181 Kahikatea Drive, Melville, Hamilton 3206, New Zealand

+647 838 9800

+647 838 9801 tony.smith@gallagher.com Certification Type / Equipment Identification Certification Program:

Certification Number:

Radio Certification M5VC30044XB The equipment identified above is / is not covered equipment prohibited from receiving an equipment authorization pursuant to 47 CFR Part 2, Subpart J, 2.903. The applicant identified above is / is not identified on the FCCs Covered List as an entity, affiliate, or subsidiary which produces equipment on the Covered List or identified as an entity which has rebranded or relabeled equipment produced by entities identified on the Covered List. I hereby attest and certify that the above statements are true and correct. Signature of Authorized Individual: 1 Printed Name:

Title of authorized signature:

Date Menardo Lazaro Technical Leader - Compliance 5/4/2023 Note this attestation shall be signed by the applicant or their direct appointee within the same legal entity. A third party agent is not permitted to sign on behalf of the applicant. 1 Signature is not subject to the FCCs authorized individual policy; (KDB 852134) and may be signed by any appropriate company official. APP-FCC-A Page 1 of 2 Rev 2 CKC Certification Services, LLC CB: US0103; NB/AB: 0976 5046 Sierra Pines Drive Mariposa, CA 95338 Phone: 1 800-500-4EMC (4362) Fax: 209-787-5568 Email: tcbadmin@ckc.com Attachment A Additional Information The FCCs Covered List includes certain telecommunications equipment and video surveillance equipment produced by specific manufacturers, their Affiliates or Subsidiaries and including any products produced by these entities which are rebranded or relabeled by other entities. (191, 184, 185, 188) 2 The FCC claims the identified equipment poses an unacceptable risk to United States national security. Telecommunications Equipment (195):

Any equipment used in fixed or mobile networks that provides advanced communications service, provided the equipment includes or uses electronic components, as defined under section 1.50001(c). Video Surveillance Equipment (205):

Any equipment that is used in fixed and mobile networks that provides advanced communications service in the form of a video surveillance service, provided the equipment includes or uses electronic components. Advanced Communications Service (195, 205) Any equipment that can be used in such a fixed or mobile broadband network to enable users to originate and receive high quality voice, data, graphics, and video telecommunications service using any technology with connection speeds of at least 200 kbps in either direction. Affiliate (183):

An entity that (directly or indirectly) owns or controls, is owned or controlled by, or is under common ownership or control with, another entity, where the term own means to have, possess, or otherwise control an equity interest (or the equivalent thereof) of more than 10 percent. Subsidiary (184):

Any entity in which such named entity directly or indirectly (1) holds de facto control or (2) owns or controls more than 50% of the total voting power of the entitys outstanding voting stock. Useful Links:

FCC Covered List https://www.fcc.gov/supplychain/coveredlist 47 CFR Part 2 Subpart J (including 2.903 and 2.911) https://www.ecfr.gov/current/title-47/chapter-I/subchapter-A/part-2/subpart-J FCC KDB System:

https://apps.fcc.gov/oetcf/kdb/index.cfm FCC Report and Order 22-84 https://docs.fcc.gov/public/attachments/FCC-22-84A1.pdf 2 Parenthetical references are citations of paragraph numbers in FCC Report and Order FCC 22-84 (ET Docket 21.232). APP-FCC-A Page 2 of 2 Rev 2

6/8/2023 Federal Communication Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21048 RE: Cover Letter To whom it may concern:

The FCC test report number 220904.1b for T12 Multi Tech Reader (Model No.: C300440-) also covers the other models of T12 Multi Tech Reader (Model No.: C300441-), T11 Multi Tech Readers (Model Nos. C300430- and C300431-) and T11 SMB Reader (Model Nos. C500430- and C500431-). All these model numbers are to be certified under FCC ID: M5VC30044XB.

1 2 3 4 5 6 7 Product Characteristics:

Radio Frequency Operating Range(s) RF Power / Field Strength Radio Frequency Circuitry Antenna Characteristics Associated Digital Circuitry Functional Capabilities Cosmetic Differences For any differences, a description is provided in the table below. Products are:

Same X X X X X X Different X

7 Description of differences:

The T11 Multi Tech (C300430-, C300431-), SMB T11 (C500430- and C500431-) and T12 Multi Tech, Black Not Potted (C300440-01-) readers have an identical circuit and PCB layout / PCB tracks with T12 Multi Tech readers (C300440- and C300441-). The differences between the T11 and T12 models lie in the shapes of the plastic enclosures and physical sizes of PCB. The sizes of non-conductive parts of the PCB are slightly different. There are no additional circuitries and no additional metal parts. The models C300430-, C500430- and C300440- come with a black enclosure, while C300431-, C500431- and C300441 have a white enclosure. The C300440-01- model, on the other hand, does not have an enclosure and is not potted. Brief statement as to why the products should qualify for family approval:

The products all share the same hardware. The radio parameters are identical among all family members. Sincerely, Menardo Lazaro Technical Leader - Compliance GALLAGHER GROUP LIMITED 181 Kahikatea Drive, Hamilton 3206, New Zealand. Private Bag 3026, Hamilton 3240, New Zealand. TEL +64 7 838 9800 FAX +64 7 838 9801 EMAIL info@gallagher.com WEB www.gallagher.com