User Manual Parts Of The Camera 1. IR LED 2. Microphone 3. Lens 4. Front motion sensor 5. DC adapter port 6. Side motion sensor 7. Indicator light 8. Memory card slot 9. USB jack 10. Left/playback button 11. ON-TEST-OFF button 12. Down/Capture Button 13. Menu Button 14. OK/Shot button 15. Right button 16. Up/Video Button 17. Speaker 18. Display screen 1 19. Lock hole Power Supply Before using the device, users can choose battery charging or DC power supply according to their needs. If you choose battery power, please insert the batteries first. This device supports 1.5 V AA batteries and 3.7V 18650 lithium batteries. If you choose to use 1.5 V AA batteries, please open the device and find the battery compartment, insert 4*1.5 V AA batteries. When inserting the battery, make sure that the battery polarity is correct. If you choose to use 3.7V 18650 lithium battery, please open the device and find the corresponding battery compartment, which can be loaded with 1 or 2 3.7V 18650 lithium battery. When installing the battery, ensure that the battery polarity is correct. (The 3.7V 18650 lithium battery of the device can be charged with a USB charger above DC5V1.5A, the indicator light of the case will turn on red when charging and the red light will turn off when fully charged) 2 When using the power adapter above DC6V1.5A (not provided) to charge, please find the DC adapter port on the bottom of the device and open the rubber, connect one end of the power adapter to the device and the other end to the power supply for supply power. Inserting The Memory Card Please prepare a memory card and insert it into the camera for saving files. Before recording, please format the memory card first. Support memory card,up to 512GB. Suggest to use class 6 or above high speed card. To avoid malfunction, the memory card should be far away from water, strong vibration,dust, hot source and direct sunlight. Do not insert the memory card forcibly. Please refer to the marking on the camera. for the memory card For the first temperature reach the ambient temperature.The camera will be time use, please wait 3 short-circuit influenced by environment temperature and humidity. Please notice protection for the camera when using it outdoor. If the capacity of memory card is full, the camera will stop recording automatically. Press the edge of the card gently to pop-up the memory card. Basic Operation Turn On And Off The Camera Switch the Mode Button toTest/Onto turn on the camera.After power on, it will pop up the battery type selection interface: 1.5V alkaline battery/3.7V lithium battery, press the up and down keys to select the corresponding battery, press the OK button to confirm. Switch the Mode Button to Off to turn off the camera. System Setup Switch Mode Button to Test, parameters. then you can set the system 4 1. Press Menu button to open the setup menu. 2. Press Up/Down button to scan all menu. Then press OK button to enter the options interface. 3. Press Up/Down button to scan all options. And press OK button to confirm options. 4. Press Menu button again to turn back to last menu or exit the setup menu. the working mode. Setup menu and function as below:
Mode take Set pictures. In photo&video mode, the camera will take a photo first, then start to record video. Options[Photo]/[Video]/[Photo&Video]. In Video mode,the camera just In photo mode,the camera just record video. Photo Resolution Set the still image resolution. Options[20MP(6144x3456P)] /[16MP(5376x3024P)] /[12MP
(4608x2592P)]/[8MP(3840x2160P)]/[5MP(3072x1728P)]/
5
[3MP(2304 x 1296P)] /[1MP(1280x720P)]. Photo Series Set the photo number of continuous shooting. In photo mode, the camera will take photos continuously. Options [1 photo]/[2 photos in series]/[3 photos in series]/[10 photos in series]. Video Resolution Set the video resolution. The higher the resolution, the shorter the video duration that can be stored, and vice versa . Options
[1920x1080P]/[1280x720P]/[848x480P]/[720x480P]/
[640x480P]/[320x240P]. TL Video Resolution Set the resolution of time lapse video . Options: [8MP (3840 x 2160P)]/[5MP (3072 x1728P)]/[3MP(2304x1296P)]. 6 Video Length Set the duration of recording a video clip. The shortest time is 3 seconds and the longest time is 2 minutes. Options3 seconds~2 minutes. Audio Recording Open this function,the camera will record audio when recording video. Options[On] /[Off]. Shot Lag Set the time of delay shooting when the camera detects the motion. In the selected time, the camera will not record any image or video. This function can avoid to store too much same event and save more capacity. Options5 seconds~60 minutes. Sensitivity Motion Sensors Set the sensitivity of the sensor. Environmental impact is small indoors, you can choose Low. In outdoor, choose Middlein is normal condition. Choose Highif the environment impact 7 huge outdoors. The temperature can also influence the sensor sensitivity. High Sensitivityapplies to mild environment. Low Sensitivity applies to cold environment. Options[Low] /[Middle] /[High]. Target Recording Time Set the target recording time. As shown in below picture, you can set the start and stop time. The camera will work just in the stated time slot. In other time, the camera will keep in standby state. Options[On]/ [Off]. Settings Set target recording time Start Stop HrMin 00 00 HrMin 00 00 MENU Back OK Select Settings Target Recording Time 2 Set the target recording time. As shown in below picture, you can set the start and stop time. The camera will work just in the stated time slot. In other time, the camera will keep in standby state. Options[On]/ [Off]. Set target recording time Start HrMin 00 00 Stop HrMin 00 00 MENU Back OK Select 8 Time Lapse In Time lapse menu, there are three options as below.
[Normal]: The camera will take pictures automatically as per set time interval. For example,set the interval time to 1 hour, the camera will take a photo each hour. If you want to observe that a plant blooms, the camera will take 24 photos in 24 hours to record the whole process of blooming.
[TL Video]: You can set the interval time.The time range is from 1 second to 24 hours. For example, set the interval to 1 hour, the camera will take a photo each hour. If the camera works for 24 hours,there will be 24 photos. These photos will be converted into a video.
[Off]: Close the time lapse function. Set time lapse HrMin Sec 30 00 00 Notification: Motion MENU Back OK Select Settings Language Set the language display on screen.Options[English]/ [Deutsch]
/[Dansk]/[Suomi]/[Svenska]/[Espaol]/[Franais]/[Italiano]/
[Nederlands]/[Portugus ] /[]/ [] /[]. 9 Endless Capture Set the camera to record video in loop. Options[On]/[Off]. Time & Date Set the date and time of camera. The date format: dd/mm/yyyy, yyyy/mm/ddmm/dd/yyyy. The time format: 24h12h. Press Right button to choose the item.Press Up/Down button to adjust the value. And press OK button to confirm. Options[Set time&date] /[Time format]/[Date format]. Photo Stamp Stamp the date&time on the photos or not. Options[Time&date] /[Date] /[Off]. Password Protection Set the power-on password of the camera. The password is four digitseach digit ranges from 0 to 9 and A to Z. If you forget the password, please reset the camera. Then all 10 parameters will reset to the factory settings. Options[On]/[Off]. WIFI SSID You can view the WIFI name of the device. WIFI Password Set and change the WIFI password. Beep Sound Open/close the button sound. Options[On]/[Off]. Format Memory Card Formatting the memory card will delete all data permanently. Before using a new memory card or a card that has been used in another device previously ,please format the memory card. Options[Yes]/ [No]. Serial NO. Set the unique serial number for the camera. The number is four digitseach digit ranges from 0 to 9 and A to Z. 11 Options[On]/[Off]. Reset Settings Restore the camera to factory default settings including password,serial number and so on. Options[On]/[Off]. Version Look up the Firmware information of the camera. Take PhotosRecord VideoPlayback Switch the Mode Button to Test. In this mode,you can take photos, record video and playback files manually. Take PhotosPress Capture button to switch to photo mode. Press Shot button to take a picture. Record Video Press Video button to switch to video mode.Press Shot button to start to record a video clip. Press Shot button again to stop recording. the playback interface. Press Up/Down button to scan photos or video. When playback video, press OK button to play the video. Press OK Playback:Press Playback button to enter 12 button again to have a pause. Press Menu button to stop playback. Press Playback button again to exit the playback mode. Playback Menu 1 Delete current file Delete the current photo or video. OptionsCancel/Delete. 2Delete all filesDelete all photo and video files in the memory card. OptionsCancel/Delete. 3Activate slide showPlayback the photos in slide way. Each photo display 3 seconds. Press OK button to stop playing. 4Write protectLock the file. It can avoid accident deletion. OptionsWrite-protect current file/Write-protect all files/
Unlock current file/Unlock all files. Working Mode Switch the Mode Button to On. After turn on the camera,the screen will display 15 seconds countdown. Then the LEDs and screen will go out. The camera begins to operate independently and enter standby mode. 13 the wild animals enter the detection range of the motion If sensors , the camera will be activated and detect the motion trail. If the wild animals continue to move to the detection zone of the sensor, record video automatically. When the wild animals leave the detection zone of the sensors , the camera will be deactivated and turn back to standby mode. the camera will take photos or Night Mode In night mode,the pictures just can display white and black. When record a video for long time in the evening, the low voltage may have a great influence on the stability of the machine. Do not record video with low voltage in the evening. Using the wall bracket You can mount the camera on a wall or tree by the supplied wall bracket. Before mounting the wall bracket you should ensure that all existing screws are tight.The best installation height distance from the ground about 1 meter. 14 Components 1.Tripod screw 2. Lock nut 3. Pivot bolts 4. Drill holes 5. Hexagonal screw 6. Wall plugs 7. Screws Mounting the wall bracket Required tools Drill 6 mm masonry/concrete drill bit Phillips head screwdriver Caution Ensure that there are no electric lines, water or heating pipes installed at the proposed drilling location. The supplied wall plugs are only suitable for mounting on concrete or stone. Before starting the installation, please check 15 your installation location carefully for its suitability for the plugs. The assembly material used must be suitable for the respective location. If in doubt, consult a professional. Install Steps Mark the drill holes by holding the foot of the wall bracket at the desired mounting location and marking the hole positions. Use a drill with a 6 mm drill bit to drill the required holes and insert the plugs and insert the wall plugs Screw the wall bracket to the wall using the supplied screws . Mount the camera on the tripod screw and screw the camera a little way on (about three turns). Turn the camera in the desired direction and lock it with the lock nut . To move the camera into its final position, undo the two pivot bolts a little, position the camera and fix the position by tightening the two pivot bolts . flush with the wall. 16 Remote Control by Mobile App/ Wi-Fi Connecting This camera can be remotely operated almost full functions via a Pad or Smartphone. Before perform remote control of this camera, an APP named GcamPro should be downloaded from Apple App Store or from Google Play Store and installed to your Pad or Smartphone.You can also scan this QR code to download directly. Connect of Camera and Pad/Smartphone via WiFi 1. Download and install the "GcamPro" APP on the mobile phone in the app store and turn on the Bluetooth and WIFI functions on the mobile phone. 2. Switch the power button of camera from "OFF" to "ON". 3. After the 15 seconds countdown finishing, the camera enter sleep working mode.(if the camera is already under working mode, please ignore step 2 and step 3. ) 4. Open the "GcamPro" APP and click the "Add Camera" button, 17 a new interface will pop up, please click the device you want to connect and click +Add to jump to the Bluetooth list.If you find the Bluetooth hotspot of GcamPro and click it, will pop up"Send bluetooth instructions..." then will pop on "WIFI on please connect" and the WIFI list will pop up automatically. Find the WIFI hotspot with the name "GcamPro******" (if you could not 18 see this hotspot , please to wait or refresh), then enter the initial password "12345678" to enter the WIFI connection;
5. After WIFI connection is successful, please turn back to APP.Users can operate the corresponding functions in the APP (view files of the memory card, settings, device information preview, albums,etc.);
19 Power button Click the power button will prompt a confirmation:Is the camera turned off? Options:CANCEL/AGREE. If you choice the agree,will exit WIFI connection and exit the APP, the device will enters the sleep hunting mode. Memory card button Click memory card button, user will see the photo and video files stored in the memory card. Click the icon EDIT on the top right corner, then can choose the pictures or videos to download,delete or share the files,you also can select all. Setting button Click Setting button, user will see the setup menu list of camera. Can set the parameters of camera on APP. Information preview button Click information preview button, user will see the interface shown as below: Camera storage,Number of files and Battery. 20 User also can see the see real-time images from the camera. Click the refresh icon, can refresh image and can store the current image to your phone album. Click the Album button to view the photo and video of the memory card.Click on the photo which you want to save to your phone. Click the icon EDIT on the top right corner, then can choose the pictures or videos to download, delete or share the files,you also can select all. Click the Setting button,user will see the setup menu list of camera and can set the parameters of camera on APP. Phone Album User can review the photo and 21 Refresh Album Setting video what have downloaded in the pad or smartphone album. Can zoom in image, playback,choose, delete and share files. 6. After the APP operation is completed, return to the main interface, click the Power off button in the upper right corner to shut down and exit the WIFI connection, the device will enters the sleep-hunting mode. Tips:
1.When connecting to WIFI, if the distance between the phone and the camera is closer, the WIFI signal will be stronger, the stability will be better, and the download speed will be faster;
2. After the operation of the APP, it is suggested to click the Power- off button in the upper right corner to shut down the APP. The camera will enter the sleep-hunting mode to save battery power;
3. When the product enters WIFI mode, if the mobile phone fails to connect WIFI after 3 minutes, the product will automatically 22 enter sleep-hunting mode;
4.When WIFI connection is successful. If there is no information interaction between the camera and the mobile phone, the camera will automatically disconnect after 3 minutes and enter the sleep-hunting mode. 5.After the device has been added to the APP, when opening the APP again, you only need to connect the camera, and then click the device to be connected, no need to add a network. Download Files To The Computer There are two ways to download files from the memory card to a computer:
By inserting the memory card into a card reader By connecting the camera to a computer using the supplied USB cable. Using a Card Reader 1. Pop-up the memory card from the camera and insert it into a card reader.Then connect the card reader to a computer. 23 2. Open [My Computer] or [Windows Explorer] and double-click the removable disk icon that represents the memory card. 3. Copy image or video files from the memory card to your computer. Connecting the Camcorder to a PC by the USB Cable 1. Connect the camera to the computer via USB cable.Turn on the camera,the screen will displayMSDC. 2. Open [My Computer] or [Windows Explorer]. A"Removable Disk" appears in the drive list. Double-click the "Removable Disk"
icon to view its contents. All files are stored in the folder named DCIM. 3. Copy the photos or files to your computer. 24 25 1. 2. 3. 4. 5. 6. 7. 8. TF 9. USB 10. /
11. --
12. /
13. 14. /
15. 16. /
17. 18. 26 19. DC 1.5 V AA 3.7V 18650 1.5 V AA 4 1.5 V AA 3.7V 18650 1~2 3.7V 18650 DC5V1.5A USB 3.7V 18650 DC6V1.5A () 27
, TF TF TF 512 GB 6 TF 28
1.5V /3.7V OK 1. 2. /
3. /
4.
29 20MP(6144x3456P)/16MP(5376x3024P)/
12MP(4608x2592P)/8MP(3840x2160P)/5MP (3072 x1728P)/3MP(2304x1296P)/1MP(1280x720P). 1 / 2 / 3 /
10 1920x1080P/1280x720P/848x480P/
720x480P/640x480P/320x240P.
:8MP(3840x2160P)/5MP (3072 x1728P)/
3MP(2304x1296P). 30 3 2 3 ~2
5 ~60 31
00 00 00 00 MENU OK 2
00 00 00 00 MENU OK 32 1 1 24 24 1 -24 1 1 24 1*24=24 00 00 30 MENU OK
[English]/[Deutsch]/[Dansk] /[Suomi]
/[Svenska]/[Espaol]/[Franais]/[Italiano]/[Nederlands]
/[Portugus ]/ []/[] /[]
33
24 12
//, OK
4 0-9 A-Z
34 WIFI WIFI WIFI WIFI 8 0-9 A-Z
4 0-9 A-Z
35
1/
36 2/
3 3 4
15 37
, 1 1. 2. 3. 4. 5. 6. 7. 38 6
, 6 39 App/ Wi-Fi Apple APP Store Play Store GcamPro Pad WiFi Pad/
1 GcamPro APP /Pad WIFI 2 OFF ON 3 15 2 3 4 GcamPro APP GcamPro_XXXX 40 12345678 WIFI ;
41 5WIFI APP APP TF 42
WIFI APP TF APP 43 APP pad 6APP WIFI APP 44 1 WIFI WIFI 2 APP 3 WIFI 3 WIFI 4 WIFI 3 5APP APP TF USB 45 1. 2. [] windows 3. USB 1. USB MSDC 2. [] windows DCIM 3. DCIM 46 FCC WARNING This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help. To maintain compliance with FCCs RF Exposure guidelines, This equipment should be installed and operated with minimum distance between 20cm the radiator your body: Use only the supplied antenna.