MM511250-11Wi-F iDatasheet Content Author initial release versions Date 1.0 2016-09-01 1. Introduction ........................................................................................................................... 3 1.1Module System Block Diagram ................................................................................... 4 1.2Module technical specifications ................................................................................ 4 2. Structure specification ........................................................................................................ 5 2.1 Module structure size .................................................................................................... 5 2.2 Hardware interface definition .................................................................................... 5 3. Wireless Specification ......................................................................................................... 6 1. Introduction MM511250-11 Wireless WIFI module is a low-power WIFI module for the Internet of Things. It supports IEEE802.11b / g / n protocol. It also embeds IPV4 / IPV6 TCP / IP, HTTP, DNS, FTP and other complete network protocols, making the terminal more reliable, convenient and easy to use. The MM511250-11 module contains RTL8711AM single-chip solution. the chip in software and hardware are used in low-power technology, the purpose is to lower the power consumption of the entire board, the product more competitive. At present, the module provides a complete serial interface functions and equipment to communicate, so you can through the serial port and mobile client to connect the cloud and equipment. IEEE 802.1b/g/n, 2.4Ghz ,1T1R internal antennas Green TX Low power saving technology Low power monitor mode Support 150Mbps Support PWM Full encryption supportWPS, WPA, WPA2, WAPI, WEP, TKIP Support IPV4/IPV6, TCP/IP protocol Support HTTP, DNS, FTP and other network protocols 1.1Module System Block Diagram As shown in Figure 1,the MM511250-11 module contains RTL8711AM single-chip solution. The module uses the internal antenna design in PCB, both for customers to reduce the cost of the antenna, but also eliminates the need to consider the antenna assembly space. figure 1. Module System Block Diagram 1.2Module technical specifications Main chip Workingfrequency WIFI Modulation Supported rates RTL8711AM 2.412~2.462GHz 802.11b/g/n(1x1) 11b: DBPSK, DQPSK, CCK, DSSS 11g: BPSK, QPSK, 16QAM, OFDM 11n: MCS0~MSC7 OFDM 11b: 1, 2, 5.5 11Mbps 11g: 6,9,12,18,24,36,48,54Mbps 11n: MCS0~7, up to 150Mbps communication interface UART PCB layer structure 2 Layers PCB size Antenna 36.0mm(L)x29.0mm(W)x1.0mm(H) internal antennas Working temperature
-40~+85 Storage temperature
-40~+125 Hardware version RTK-8711AM_36*29_2LVer:1.1 2. Structure specification 2.1 Module structure size The size of the module as shown above length:36.0mm,width:29.0mm, thickness 1.0mm (error +/- 0.1mm) 2.2 Hardware interface definition PIN Signal Name Description 5VDD MCU_UART_RX MCU_UART_TX AGND AGND Supply Input Pin UART receive data UART transmit data Ground Ground for SMT 1 2 3 4 5,6 3. Wireless Specification 1: 802.11b mode Item Specification Mode Channel Data rate Spec IEEE802.11b DSSS / CCK CH1 to CH11 1, 2, 5.5, 11Mbps TX Characteristics Min. Typ. Max. Unit Remark 1. Power Levels(Calibrated) 1) 16dBm Target 2. Spectrum Mask @ target power 1) fc +/-11MHz to +/-22MHz 2) fc > +/-22MHz 3. Frequency Error 14.5 16
-
-
-15
-
-
0 17.5
-30
-50 dBm dBr dBr
+15 ppm RX Characteristics Min. Typ. Max. Unit 4 Minimum Input Level Sensitivity 1) 1Mbps (FER8%) 2) 2Mbps (FER8%) 3) 5.5Mbps (FER8%) 4) 11Mbps (FER8%) 5 Maximum Input Level (FER8%)
-
-
-
-
-91
-90
-88
-84 0
-93
-93
-90
-86 0.5 dBm dBm dBm dBm dBm 2: 802.11g mode Item Specification Mode Channel Data rate Spec IEEE802.11g OFDM CH1 to CH11 6, 9, 12, 18, 24, 36, 48, 54Mbps TX Characteristics Min. Typ. Max. Unit 1. Power Levels 1) 12dBm Target @6Mbps 2) 12dBm Target @54Mbps 11.5 11.5 12 12 13.5 13.5 2. Spectrum Mask @ target power 1) at fc +/- 11MHz 2) at fc +/- 20MHz
-
-
3) at fc > +/-30MHz 3 Constellation Error(EVM)@ target power
-
1) 6Mbps 2) 9Mbps 3) 12Mbps 4) 18Mbps 5) 24Mbps 6) 36Mbps 7) 48Mbps 8) 54Mbps
-
-
-
-
-
-
-
-
-
-
-
-22
-22
-23
-24
-24
-27
-28
-30
-20
-28
-40
-25
-25
-26
-27
-27
-30
-31
-32 dBm dBm dBr dBr dBr dB dB dB dB dB dB dB dB 4 Frequency Error
-15 0
+15 ppm RX Characteristics Min. Typ. Max. Unit 5 Minimum Input Level Sensitivity 1) 6Mbps (PER 10%) 2) 9Mbps (PER 10%)
-
-
-88
-88
-90
-90 dBm dBm 3) 12Mbps (PER 10%) 4) 18Mbps (PER 10%) 5) 24Mbps (PER 10%) 6) 36Mbps (PER 10%) 7) 48Mbps (PER 10%) 8) 54Mbps (PER 10%) 6 Maximum Input Level (PER 10%) 3802.11n (HT20) mode
-
-
-
-
-
-
-86
-84
-81
-78
-73
-72 0
-88
-86
-83
-80
-75
-74 0.5 dBm dBm dBm dBm dBm dBm dBm Item Spec Specification IEEE802.11n HT20 @ 2.4GHz Mode Channel OFDM CH1 to CH11 Data rate (MCS index) MCS0/1/2/3/4/5/6/7 TX Characteristics Min. Typ. Max. Unit 1. Power Levels 1) 12dBm Target@MCS0 11.5 12 13.5 dBm 2) 12dBm Target@MCS7 11.5 12 13.5 dBm 2. Spectrum Mask @target power 1) at fc +/- 11MHz 2) at fc +/- 20MHz 3) at fc > +/-30MHz
-
-
-
3. Constellation Error(EVM)@ target
-
-
-
-20 dBr
-28 dBr
-45 dBr power 1) MCS0 2) MCS1 3) MCS2 4) MCS3 5) MCS4 6) MCS5 7) MCS6 8) MCS7
-
-
-
-
-
-
-
-
-22
-24
-26
-28
-26
-28
-26
-28
-26
-28
-28
-30
-28
-30
-28
-31 dB dB dB dB dB dB dB dB 4. Frequency Error
-15 0
+15 ppm RX Characteristics Min. Typ. Max. Unit 5. Minimum Input Level Sensitivity 1) MCS0 (PER 10%) 2) MCS1 (PER 10%) 3) MCS2 (PER 10%) 4) MCS3 (PER 10%) 5) MCS4 (PER 10%) 6) MCS5 (PER 10%) 7) MCS6 (PER 10%) 8) MCS7 (PER 10%) 6. Maximum Input Level (PER 10%)
-
-
-
-
-
-
-
-
-
-88
-90 dBm
-85
-87 dBm
-83
-85 dBm
-80
-82 dBm
-77
-79 dBm
-77
-79 dBm
-71
-73 dBm
-69
-71 dBm 0 0.5 dBm 4802.11n (HT40) mode Item Spec Specification IEEE802.11n HT40 @ 2.4GHz Mode Channel OFDM CH3 to CH11 Data rate (MCS index) MCS0/1/2/3/4/5/6/7 TX Characteristics Min. Typ. Max. Unit 1. Power Levels (Calibrated) 1) 12dBm Target@MCS0 11.5 12 13.5 dBm 2) 12dBm Target@MCS7 11.5 12 13.5 dBm 2. Spectrum Mask @14dBm 1) at fc +/- 22MHz 2) at fc +/- 40MHz 3) at fc > +/-60MHz
-
-
-
-
-
-
-20 dBr
-28 dBr
-45 dBr 3. Constellation Error(EVM)@target power 1) MCS0 2) MCS1 3) MCS2 4) MCS3 5) MCS4 6) MCS5
-
-
-
-
-
-
-26
-28
-22
-24
-22
-24
-26
-28
-26
-28
-26
-28 dB dB dB dB dB dB 7) MCS6 8) MCS7
-
-
-27
-29
-29
-31 dB dB 4. Frequency Error
-15 0
+15 ppm RX Characteristics Min. Typ. Max. Unit 5. Minimum Input Level Sensitivity 1) MCS0 (PER 10%) 2) MCS1 (PER 10%) 3) MCS2 (PER 10%) 4) MCS3 (PER 10%) 5) MCS4 (PER 10%) 6) MCS5 (PER 10%) 7) MCS6 (PER 10%)
-
-
-
-
-
-
-
-86
-88 dBm
-83
-85 dBm
-81
-83 dBm
-77
-79 dBm
-74
-76 dBm
-69
-71 dBm
-69
-71 dBm 8) MCS7 (PER 10%)
-
-67
-69 dBm 6. Maximum Input Level (PER 10%)
-
0 0.5 dBm interference FCC Statement This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. NOTE: this equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient of relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit difference from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Important Note:
Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Country Code selection feature to be disabled for products marketed to the US/Canada. 1. The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2. The transmitter module may not be co-located with any other transmitter or antenna. As long as the three conditions above are met, further transmitter testing will not be required. However, the OEM is still responsible for testing their end-product for any additional compliance requirements required with this module installed. integrator Important Note:
In the event that these conditions cannot be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. End Product Labeling:
The final end product must be labeled in a visible area with the following Contains FCC ID: 2ADQOMDWF01 If the FCC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording ID:
2ADQOMDWF01. Manual Information to the End User:
The OEM integrator has to be aware not provide information to the end user regarding how to install or remove this RF module in the users manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. When the module is installed inside another device, the user manual of this device must contain below warning statements;
following; Contains Transmitter Module FCC such as the 1. This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:
1) this device may not cause harmful interference, 2) this device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. The devices must be installed and used in strict accordance with the manufacturers instructions as described in the user documentation that comes with the product.