FCC ID: E5MDS-MERCURY3651 WIRELESS IP/ETHERNET TRANSCEIVER

 

MDS MercuryTM Series l a u n a M e c n e r e f e R Wireless IP/Ethernet Transceiver Covering all AP and Remote Units including Mercury 900, 3650, and Option Set 1 Remotes 05-4446A01, Rev. E MARCH 2009 TABLE OF CONTENTS 1 PRODUCT OVERVIEW & APPLICATIONS ............ 1 1.1 ABOUT THIS MANUAL................................................................................................... 3 1.1.1 Start-Up Guide .................................................................................................................... 3 1.1.2 Online Access to Manuals ................................................................................................... 3 1.1.3 Conventions Used in This Manual ....................................................................................... 3 1.2 PRODUCT DESCRIPTION............................................................................................. 4 1.2.1 Model Offerings ................................................................................................................... 6 1.2.2 Remote Radio with Option Set 1 ......................................................................................... 7 1.2.3 GE MDS P23 Protected Network (Redundant) Configuration ............................................. 8 1.2.4 External GPS PPS Option ................................................................................................... 9 1.3 APPLICATIONS .............................................................................................................. 9 1.3.1 Mobile/Fixed Data System .................................................................................................. 9 1.3.2 Wireless LAN ..................................................................................................................... 10 1.3.3 Point-to-Point LAN Extension .............................................................................................11 1.3.4 Serial Radio Network Connectivity .....................................................................................11 1.3.5 Multiple Protocols and/or Services .....................................................................................11 1.3.6 Wireless LAN with Mixed Services .................................................................................... 12 1.3.7 Upgrading Older Wireless Network with Serial Interfaces ................................................. 13 1.4 NETWORK DESIGN CONSIDERATIONS.................................................................... 14 1.4.1 Extending Network Coverage with Repeaters ................................................................... 14 1.4.2 Protected Network Operation using Multiple APs .............................................................. 16 1.4.3 Collocating Multiple Radio Networks ................................................................................. 16 1.5 GE MDS CYBER SECURITY SUITE............................................................................ 17 1.6 ACCESSORIES ............................................................................................................ 19 2 TABLETOP EVALUATION & TEST SETUP............. 21 2.1 OVERVIEW................................................................................................................... 23 2.2 STEP 1: CONNECT THE ANTENNA PORTS............................................................... 23 2.3 STEP 2: CONNECT THE PRIMARY POWER.............................................................. 24 05-4446A01, Rev. E Mercury Reference Manual i 2.4 STEP 3: CONNECT PC TO THE TRANSCEIVER ....................................................... 25 2.5 STEP 4: REVIEW TRANSCEIVER CONFIGURATION................................................ 25 2.5.1 Getting Started .................................................................................................................. 25 2.5.2 Procedure .......................................................................................................................... 25 2.5.3 Basic Configuration Defaults ............................................................................................. 25 2.6 STEP 5: CONNECT LAN OR SERIAL DATA EQUIPMENT.......................................... 26 2.6.1 Option Set 1 Connectors ................................................................................................... 28 2.7 STEP 6: CHECK FOR NORMAL OPERATION ............................................................ 29 3 DEVICE MANAGEMENT......................................... 31 3.1 INTRODUCTION .......................................................................................................... 33 3.1.1 Differences in the User Interfaces ..................................................................................... 33 3.2 ACCESSING THE MENU SYSTEM ............................................................................. 35 3.2.1 Methods of Control ............................................................................................................ 36 3.2.2 PC Connection and Log In Procedures ............................................................................. 36 3.2.3 Navigating the Menus ........................................................................................................ 40 3.3 BASIC OVERVIEW OF OPERATION........................................................................... 42 3.3.1 Starting Information Screen ............................................................................................... 42 3.3.2 Main Menu ......................................................................................................................... 43 3.4 CONFIGURING NETWORK PARAMETERS ............................................................... 45 3.4.1 Network Configuration Menu ............................................................................................. 45 3.4.2 Ethernet Port Configuration Menu ..................................................................................... 56 3.4.3 Bridge Configuration .......................................................................................................... 58 3.4.4 SNMP Agent Configuration ................................................................................................ 58 3.4.5 AP Location Push Config Menu ......................................................................................... 60 3.4.6 SNTP Server Configuration ............................................................................................... 64 3.5 RADIO CONFIGURATION............................................................................................ 65 3.5.1 Radio Configuration Menu ................................................................................................. 65 3.5.2 Serial Port Configuration ................................................................................................... 76 3.6 MODBUS / TCP SERVER CONFIGURATION ............................................................. 88 3.6.1 Modbus/TCP in Mercury TransceiversAn Overview ...................................................... 88 3.6.2 Menu Selections ................................................................................................................ 89 3.7 SECURITY CONFIGURATION MENU ......................................................................... 92 3.7.1 Device Security Menu ....................................................................................................... 93 ii Mercury Reference Manual 05-4446A01, Rev. E 3.7.2 Wireless Security Menu ..................................................................................................... 95 3.7.3 IEEE 802.1x Device Authentication ................................................................................... 97 3.7.4 Manage Certificates .......................................................................................................... 99 3.8 REDUNDANCY CONFIGURATION (AP ONLY) ......................................................... 102 3.9 GPS CONFIGURATION (REMOTE ONLY) ................................................................ 107 3.10 DEVICE INFORMATION MENU ............................................................................... 109 3.11 PERFORMANCE INFORMATION MENU..................................................................110 3.12 MAINTENANCE/TOOLS MENU ............................................................................... 123 3.12.1 Installing Firmware via TFTP ........................................................................................ 129 3.12.2 Auto Firmware Upgrade Menu (AP Only) ..................................................................... 138 3.13 PERFORMANCE OPTIMIZATION............................................................................ 140 3.13.1 Proper Operation and What to Look For ....................................................................... 143 4 TROUBLESHOOTING & RADIO MEASUREMENTS.................................................. 147 4.1 TROUBLESHOOTING................................................................................................ 149 4.1.1 Interpreting the Front Panel LEDs ................................................................................... 149 4.1.2 Troubleshooting With the Embedded Management System ........................................... 150 4.1.3 Using Logged Operation Events ..................................................................................... 153 4.1.4 Alarm Conditions ............................................................................................................. 154 4.1.5 Correcting Alarm Conditions ............................................................................................ 155 4.1.6 Logged Events ................................................................................................................ 155 4.2 RADIO (RF) MEASUREMENTS................................................................................. 157 4.2.1 Antenna System SWR and Transmitter Power Output .................................................... 157 4.2.2 Antenna Aiming (For Directional Antennas)...................................................................... 158 5 PLANNING A RADIO NETWORK ......................... 161 5.1 INSTALLATION PLANNING ....................................................................................... 163 5.1.1 General Requirements .................................................................................................... 163 5.1.2 Site Selection .................................................................................................................. 164 5.1.3 Terrain and Signal Strength ............................................................................................. 165 5.1.4 Antenna & Feedline Selection ......................................................................................... 165 5.1.5 How Much Output Power Can be Used? ........................................................................ 169 5.1.6 Conducting a Site Survey ................................................................................................ 169 5.1.7 A Word About Radio Interference .................................................................................... 170 05-4446A01, Rev. E Mercury Reference Manual iii 5.1.8 ERP Compliance at 900 MHz .......................................................................................... 172 5.1.9 ERP Compliance at 3650 MHz ........................................................................................ 173 5.2 dBm-WATTS-VOLTS CONVERSION CHART............................................................ 174 6 TECHNICAL REFERENCE.................................... 175 6.1 DATA INTERFACE CONNECTORS ........................................................................... 177 6.1.1 LAN Port .......................................................................................................................... 177 6.1.2 COM1 Port ...................................................................................................................... 177 6.2 SPECIFICATIONS ...................................................................................................... 178 6.3 NOTES ON SNMP...................................................................................................... 180 6.3.1 Overview ......................................................................................................................... 180 7 GLOSSARY OF TERMS & ABBREVIATIONS...... 185 Copyright Notice This publication is protected by U.S.A. copyright law. Copyright 2009, GE MDS. All rights reserved. ISO 9001 Registration GE MDS adheres to the internationally-accepted ISO 9001 quality system standard. To our Customers We appreciate your patronage. You are our business. We promise to serve and anticipate your needs. We will strive to give you solutions that are cost effective, innovative, reliable and of the highest quality possible. We promise to build a relationship that is forthright and ethical, one that builds confidence and trust. Related Materials on the Internet Data sheets, frequently asked questions, case studies, applica-

tion notes, firmware upgrades and other updated information is available on the GE MDS Web site at www.GEmds.com. About GE MDS Over two decades ago, GE MDS began building radios for business-critical applications. Since then, we have installed thousands of radios in over 110 countries. To succeed, we overcame impassable terrain, brutal operating conditions and disparate, complex network configurations. We also became experts in wireless communication standards and system applications worldwide. The result of our efforts is that today, thousands of utilities around the world rely on GE MDS-based wireless networks to manage their most critical assets. iv Mercury Reference Manual 05-4446A01, Rev. E The majority of GE MDS radios deployed since 1985 are still installed and performing within our customers' wireless networks. Thats because we design and manufacture our products in-house, according to ISO 9001 which allows us to control and meet stringent global quality standards. including oil and gas production and transportation, water/wastewater Thanks to our durable products and comprehensive solutions, GE MDS is the wireless leader in industrial automation treatment, supply and transportation, electric transmission and distribution and many other utility applications. GE MDS is also at the forefront of wireless communications for private and public infrastructure and online transaction processing. Now is an exciting time for GE MDS and our cus-

tomers as we look forward to further demonstrating our abilities in new and emerging markets. As your wireless needs change you can continue to expect more from GE MDS. We'll always put the performance of your network above all. Visit us at www.GEmds.com for more information. OPERATIONAL & SAFETY NOTICES RF Exposure

(900 MHz models) Professional installation required. The radio equipment described in this guide emits radio frequency energy. Although the power level is low, the concentrated energy from a directional antenna may pose a health hazard. Do not allow people to come closer than 23 cm (9 inches) to the antenna when the transmitter is operating in indoor or outdoor environments. More information on RF exposure is on the Internet at www.fcc.gov/oet/info/documents/bulletins

. To meet co-location requirements, the FCC requires a 20cm (7.87 inch) separation distance between the units WIFI and fundamental antenna installations. See able power/antenna settings for this radio. ERP Compliance at 900 MHz on Page 172 for allow-

RF Exposure

(3650 MHz models) Professional installation required. The transceiver described here emits radio frequency energy. Although the power level is low, the concentrated energy from a directional antenna may pose a health hazard. Do not allow people to come closer than 22 cm (8.7 inches) to the antenna when the transmitter is operating. This calculation is based on an 18 dBi panel antenna. Refer also to the table below, which lists required separation dis-

tances. Additional information on RF exposure is available on the Internet at www.fcc.gov/oet/info/documents/bulletins. See 3650 MHz radio. on Page 173 for allowable power/antenna settings for this ERP Compliance at To meet co-location requirements, the FCC requires a 20cm (7.87 inch) separation distance between the units WIFI and fundamental antenna installations. 05-4446A01, Rev. E Mercury Reference Manual v us Notice (Remote Transceiver Only) CSA/

This product is approved for use in Class 1, Division 2, Groups A, B, C & D Hazardous Locations. Such locations are defined in Article 500 of the National Fire Protection Association (NFPA) publication

, otherwise known as the National Electrical Code. NFPA 70 The transceiver has been recognized for use in these hazardous locations by the Canadian Standards Association

(CSA) which also issues the US mark of approval (CSA/

C22.2 No. 213-M1987.

). The CSA Certification is in accordance with CSA STD US CSA Conditions of Approval: The transceiver is not acceptable as a stand-alone unit for use in the hazardous locations described above. It must either be mounted within another piece of equipment which is certified for hazardous locations, or installed within guidelines, or conditions of approval, as set forth by the approving agencies. These conditions of approval are as follows:

The transceiver must be mounted within a separate enclosure which is suitable for the intended application. The antenna feedline, DC power cable and interface cable must be routed through conduit in accor-

dance with the National Electrical Code. Installation, operation and maintenance of the transceiver should be in accordance with the trans-

ceiver's installation manual, and the National Electrical Code. Tampering or replacement with non-factory components may adversely affect the safe use of the transceiver in hazardous locations, and may void the approval. A power connector with screw-type retaining screws as supplied by GE MDS must be used. EXPLOSION HAZARD!

Do not disconnect equipment unless power has been switched off or the area is known to be non-hazardous. Refer to Articles 500 through 502 of the National Electrical Code (NFPA 70) for further information on hazardous locations and approved Division 2 wiring methods. FCC Part 15 Notices The transceiver series complies with Part 15 of the FCC Rules. Operation is subject to the fol-

lowing two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device is specifically designed to be used under Section 15.247 of the FCC Rules and Regulations. Any unauthorized modification or changes to this device without the express approval of Micro-

wave Data Systems may void the users authority to operate this device. Furthermore, the Mercury Series is intended to be used only when installed in accordance with the instructions outlined in this manual. Failure to comply with these instructions may also void the users authority to operate this device. Part 15 rules also require that the Effective Isotropic Radiated Power (EIRP) from a Mercury Series 900 MHz installation not exceed 36 dBm. For the Mercury 3650, EIRP must not exceed 1-watt per MHz. Refer to this manual for more information. vi Mercury Reference Manual 05-4446A01, Rev. E Industry Canada RSS Notices Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. To reduce potential radio interference to other users, the antenna type and its gain should be chosen so that the Equivalent Isotropic Radiated Power (EIRP) is not more than that permitted for suc-

cessful communication. This device has been designed to operate with the antennas listed in this manual. Antennas not included here are strictly prohibited for use with this device. The required antenna impedance is 50 ohms. Manual Revision and Accuracy This manual was prepared to cover a specific version of firmware code. Accordingly, some screens and features may differ from the actual unit you are working with. While every reasonable effort has been made to ensure the accuracy of this guide, product improvements may also result in minor differences between the manual and the product shipped to you. If you have additional questions or need an exact specification for a product, please contact our Customer Service Team using the information at the back of this guide. In addition, manual updates can often be found on the GE MDS Web site at www.GEmds.com. Environmental Information The manufacture of this equipment has required the extraction and use of natural resources. Improper disposal may contaminate the environment and present a health risk due to hazardous substances contained within. To avoid dissemination of these substances into our environment, and to limit the demand on natural resources, we encourage you to use the appropriate recycling sys-

tems for disposal. These systems will reuse or recycle most of the materials found in this equipment in a sound way. Please contact GE MDS or your supplier for more information on the proper dis-

posal of this equipment. 05-4446A01, Rev. E Mercury Reference Manual vii viii Mercury Reference Manual 05-4446A01, Rev. E 1 PRODUCT OVERVIEW AND APPLICATIONS 1 Chapter Counter Reset Paragraph Contents 1.1 ABOUT THIS MANUAL ......................................................... 3 1.1.1 Start-Up Guide ....................................................................... 3 1.1.2 Online Access to Manuals ...................................................... 3 1.1.3 Conventions Used in This Manual ......................................... 3 1.2 PRODUCT DESCRIPTION ................................................... 4 1.2.1 Model Offerings ...................................................................... 6 1.2.2 Remote Radio with Option Set 1 ............................................ 7 1.2.3 GE MDS P23 Protected Network (Redundant) Config. ......... 8 1.2.4 External GPS PPS Option ..................................................... 9 1.3 APPLICATIONS..................................................................... 9 1.3.1 Mobile/Fixed Data System ..................................................... 9 1.3.2 Wireless LAN ......................................................................... 10 1.3.3 Point-to-Point LAN Extension ................................................ 11 1.3.4 Serial Radio Network Connectivity ......................................... 11 1.3.5 Multiple Protocols and/or Services ......................................... 11 1.3.6 Wireless LAN with Mixed Services ......................................... 12 1.3.7 Upgrading Older Wireless Network with Serial Interfaces ..... 13 1.4 NETWORK DESIGN CONSIDERATIONS ............................ 14 1.4.1 Extending Network Coverage with Repeaters ....................... 14 1.4.2 Protected Network Operation using Multiple APs .................. 16 1.4.3 Collocating Multiple Radio Networks ..................................... 16 1.5 GE MDS CYBER SECURITY SUITE .................................... 17 1.6 ACCESSORIES..................................................................... 19 05-4446A01, Rev. E Mercury Reference Manual 1 2 Mercury Reference Manual 05-4446A01, Rev. E Reference Manual is one of two publications provided for users of 1.1 ABOUT THIS MANUAL This the Mercury Series transceiver system. It contains detailed product information, an overview of common applications, a screen-by-screen review of the menu system, technical specifications, suggested settings for various scenarios, and troubleshooting information. This manual should be available to all personnel responsible for network design, setup, commissioning and troubleshooting of the radios. TM Start-Up Guide 1.1.1 Start-Up Guide The Mercury Series panion publication to the Reference Manual. It is a smaller book, with a specific purposeto guide an installer in the basic steps for getting a transceiver on the air and communicating with other units in a network. It provides only the essential information installers need for getting their equipment up and running in the shortest time possible.

(Part No. 05-4558A01) is a com-

1.1.2 Online Access to Manuals In addition to printed manuals, many users need access to documents electronically. This is especially useful when you need to access docu-

mentation while traveling, or want to share a document with another user in the field. Electronic documents also allow searching for a spe-

cific term or subject, especially in larger manuals. Access manuals for our equipment anytime from our Web site at www.GEmds.com page and select window appears to help you locate the manual you need. Simply click the Product Manuals from the drop-down list. A search Downloads tab at the top of the home Online manuals are provided as PDF files in the Adobe Acrobat dard. If necessary, download the free reader for PDF files from

. www.adobe.com stan-

1.1.3 Conventions Used in This Manual On-Screen Menu Items On-screen menu items or command entries are presented in a distinctive font to set them apart from regular text (for example: Network Name, IP Address, Password). You will find this font most often in Chapter 3, where the menu system is discussed in detail. When variable settings or a range of options are available for a menu option, the items are pre-

sented inside brackets, with the default setting (if any) shown last after a semicolon:

[available settings or range; default setting]

05-4446A01, Rev. E Mercury Reference Manual 3 Menu Strings To help show the path to a menu selection, navigation strings are used in several places in this manual. For example, suppose you want to view or set the Network Name assigned to your system. This item is located in the Network Configuration Menu, so the navigation string in the text would appear as shown:

Main Menu>>Network Configuration>>Network Name By following this order of menus, you can quickly reach the desired menu. 1.2 PRODUCT DESCRIPTION The GE MDS Mercury SeriesTM transceiver (Figure 1-1) is an easy-to-install wireless solution offering extended range, secure opera-

tion, and multi-megabit performance in a compact and rugged package. The transceiver is ideally suited for demanding applications in fixed or mobile environments, where reliability and range are paramount. The transceivers are commonly used to convey text documents, graphics, e-mail, video, Voice over IP (VoIP), and a variety of other application data between mobile, fixed-point, and WAN/LAN-based entities. Based on multi-carrier Orthogonal Frequency Division Multiplexing

(OFDM), the transceiver features high speed/low latency, basic Quality of Service (QoS) for prioritizing traffic, Ethernet and serial encapsula-

tion, and network roaming. It also provides enhanced security features including AES encryption and IEEE 802.1x Device Authentication, making the Mercury system the best combination of security, range, and speed of any industrial wireless solution on the market today. Invisible place holder Figure 1-1. The GE MDS Mercury SeriesTM Transceiver

(Remote unit shown, AP similar in appearance) Rugged Packaging The transceivers are housed in a compact and rugged die cast-aluminum case that needs only protection from direct exposure to the weather. This 4 Mercury Reference Manual 05-4446A01, Rev. E Simple Installation Secure Operation Robust Radio Operation Flexible Services one enclosure contains all necessary components for radio operation and data communications. Mercury Transceivers are designed for rapid and trouble-free installa-

tion. For basic services, you simply connect the antennas (900 or 3650 MHz as required, and GPS), connect your data equipment, apply pri-

mary power, and set some operating parameters. No license is required for 900 MHz operation in the USA, Canada, and many other countries. A simple registration process is required for 3650 MHz operation in the USA. Check requirements for your region before placing the equipment into service. (NOTE: 3650 MHz is for APs and Fixed Remote stations.) Most installations employ an omni-directional antenna at the Access Point (AP) location and mobile stations. Fixed Remote stations often employ a directional antenna aimed at the AP. Regardless of the type used, antennas are a vital part of the system and must be chosen and installed correctly. Refer to INSTALLATION PLANNING on Page 163 for guidance on choosing suitable antennas and installation sites. Data network security is a vital issue in todays wireless world. Mercury transceivers provide multiple tools to help you build a network that min-

imizes the risk of eavesdropping and unauthorized access. Some are inherent in the radios operation, such as the use of 900 MHz spread-spectrum transmissions; others include AES data encryption, enabling/disabling channels, IEEE 802.1X port blocking, approved device lists, secure devices management protocols, and password pro-

tection. Security is not a one-step process that can simply be turned on and for-

gotten. It must be practiced and enforced at multiple levels, 24 hours-a-day and 7 days-a-week. See GE MDS CYBER SECURITY SUITE on Page 17 for more information about the transceivers secu-

rity tools. The transceivers are designed for operation in the 900 MHz license-free Industrial, Scientific, and Medical (ISM) band and the 3650-3700 MHz registered band. They provide consistent, reliable coverage over a large geographic area. Mobile range depends on many factors, including terrain, building den-

sity, antenna gain, and speed of travel. The unit is designed for suc-

cessful application in a variety of mobile environments, and offers the best combination of range, speed and robustness available in an indus-

trial wireless package today. By using multiple Access Points, a network can be created that provides consistent, reliable coverage over a large metropolitan area. See SPECIFICATIONS on Page 178 for more information on transmission range. Users with a mix of equipment having Ethernet and serial data interfaces can use this equipment via a Remote transceiver. The transceiver pro-

vides services in data networks that are migrating from legacy 05-4446A01, Rev. E Mercury Reference Manual 5 Flexible Management serial/EIA-232-based hardware to the faster and more easily interfaced Ethernet protocol. You can locally or remotely configure, commission, troubleshoot, and maintain the transceiver. Four different modes of access are available:

local RS-232 console terminal, local or remote IP access (via Telnet or SSH), web browser (HTTP, HTTPS), and SNMP (v1/v2/v3) All IP access interfaces are available through the units wired Ethernet port and over the air. The text-based interfaces (RS-232 console, Telnet, and SSH) are imple-

mented in the form of easy-to-follow menus, and the terminal server provides a wizard to help you configure the units correctly. Transceiver Features The transceivers design makes the installation and configuration easy, while allowing for future changes. Industrial-Grade ProductExtended temperature range for trouble-free operation in extreme environments. Robust Radio CommunicationsDesigned to operate over long distances in dense, high-interference environments. Robust Network SecurityPrevents common attack schemes and hardware from gaining access or control of the network. Common attack events are logged and reported by alarms. Transmission SpeedOperation at 1.5 Mbps is over 100-times faster than 9.6 kbps radios. Plug-and-Play ConnectivityAP or Remote configuration requires minimal setup. Built-in GPS ReceiverGPS technology is used for timing and location data. The only external equipment needed for this func-

tionality is a GPS antenna available from GE MDS). 1.2.1 Model Offerings The transceiver comes in two primary modelsAccess Point and Remote. Unique hardware is used for each model. Of the Remote radios, there are two sub-types availableStandard Remote and Remote with Option Set 1, both of which support Ethernet and serial services. Table 1-1 summarizes each radios interface services. Table 1-1. Transceiver Models and Data Interface Services Model Sub-Type Access Point N/A Remote Standard Remote Remote w/Option Set 1 Ethernet/LAN1 COM11 Yes Yes Yes Yes Yes Yes USB No No Yes Integrated WiFi No No Yes NOTES 1. COM1 provides access to the embedded Management System for all units. 6 Mercury Reference Manual 05-4446A01, Rev. E Available Frequency Bands At the time of publication, Mercury transceivers are offered in two dif-

ferent frequency bands: 902-928 MHz (Mercury 900) and 3.653.70 GHz (Mercury 3650). The 900 MHz unit operates in a license-free spec-

trum (frequency hopping spread spectrumFHSS), which may be used by anyone in the USA, provided FCC Part 15 rules are observed. Canada, and certain other countries allow license-free operation in this bandcheck your countrys requirements. The 3.653.70 GHz radio operates in a registered band using conten-

tion-based protocol, which provides additional protection from interfer-

ence, but it requires FCC registration before operation can begin. Other restrictions may apply based on your location and grandfathered FSS users. Check local requirements before operation. GE MDS has pub-

lished a whitepaper containing frequently asked questions about the 3.653.70 GHz band. To obtain a copy, request publication 05-4734A02. (NOTE: 3650 MHz is for APs and Fixed Remote stations.) Operationally, the Mercury 3650 has two key differences from the Mer-

cury 900: First, it operates on a different RF band (3.653.70 GHz). Second, it only requires GPS for TDD synchronization of the Access Points, which may or may not be needed for an installation. Access Point or Remote?Identification Tip The outward appearance of AP and Remote radios is nearly identical, however, the hardware for each type is different and they are not inter-

changeable. An quick way to identify them is to observe the color of the gasket seal in the center of the radio case. APs have a black gasket, while Remote units have a yellow gasket. In addition to gasket color, a label on the top of each radio identifies it as an AP or Remote unit. If the label shows an A suffix, it is an AP. If it shows a R suffix, it is a Remote. 1.2.2 Remote Radio with Option Set 1 The Option Set 1 Remote is similar to and compatible with the stan-

dard Mercury Remote. It contains the same 900 MHz radio, user inter-

face, and primary functionality as the Standard Remote. The Standard Remote can be directly replaced with the Option Set 1 Remote. The key differences are the additional physical interfaces: an IEEE 802.11b/g WiFi networking module, a USB device port, a USB host port, and a second Ethernet port on the radio enclosure. The USB ports are used for device management. The host port accepts a flash drive and can be used to transfer firmware and configuration files. The two Ethernet ports are connected to an internal, integrated switch and included in the Layer 2 bridge. 05-4446A01, Rev. E Mercury Reference Manual 7 The internal WiFi module has FCC modular approval and may only be operated by connecting one of the GE MDS approved antennas (see 802.11 WiFi Module Specications below) to the reverse-SMA con-

nector on the radios front panel. Only these antennas may be used. The WiFi module can operate as an 802.11 Access Point or Infrastructure Station, according to user configuration. The operational mode (AP, Infra-

structure RM) and frequency can be configured through the unit's user interface. Invisible place holder Figure 1-2. Mercury Remote with Option Set 1

(Note interface connector differences from Standard Remote) 802.11 WiFi Module Specifications The specifications listed below are unique to Remotes with Option Set 1, which contain a 2.4 GHz WiFi module. SPECIFICATIONS on Page 178 contains a complete list of general Mercury Series specifica-

tions. Protocol:

Frequency Range:

Maximum Transmit Power:

Permissible Antennas:

FCC:

FCC ID:

WiFi Antenna Connector:

IEEE 802.11b/g OFDM 6 to 54Mbps, CCK 1 to 11Mbps 2400 to 2500MHz 15 dBm MDS 97-4278A36 MDS 97-4278A34 MDS 97-4278A35 Part 15C VRA-SG9011028 Female Reverse SMA 1.2.3 GE MDS P23 Protected Network (Redundant) Configuration For mission-critical applications, a Protected Network Station is also offered. This unit incorporates two Access Points, two power supplies, and a switchover logic board that automatically selects between Trans-

ceiver A and Transceiver B as the active radio. Figure 1-3 shows the 8 Mercury Reference Manual 05-4446A01, Rev. E protected chassis. For system-level information on this product, refer to MDS publication 05-4161A01. Invisible place holder Figure 1-3. MDS P23 Protected Network Station

(incorporates two transceivers, with automatic switchover) 1.2.4 External GPS PPS Option The External GPS Precise Positioning Service (PPS) option allows for an external GPS device to provide the PPS input to the Mercury. This is useful in installations where multiple radios require GPS timing. This option prevents each Mercury from requiring its own GPS antenna. Refer to the electrical specifications in the External GPS PPS Option section on Page 180. This option is only available in hardware revision 1.0.2 or later. 1.3 APPLICATIONS The following sections provide illustrations of typical transceiver instal-

lations. This is an overview only. A Network Administrator should be involved in all installation planning activities. 1.3.1 Mobile/Fixed Data System Mercury transceivers support high-speed data communications in a mobile environment. In this application, Remote radios roam between different Access Points, providing seamless transitions and continuous coverage throughout a municipal area. Figure 1-4 shows an example of an integrated system employing both mobile and fixed Mercury trans-

ceivers. NOTE: 3650 MHz is for APs and Fixed Remote stations only. 05-4446A01, Rev. E Mercury Reference Manual 9 Mercury AP Invisible place holder Mercury remote RTU/PLC

(Ethernet) Mercury remote Long Range WLAN Video Surveillance RS-232 MDS 4710 RS-232 RS-232 RTU/PLC

(Serial) RTU/PLC

(Serial) MDS 4790 Master Radio MDS 4710 Licensed Serial/IP Integration MDS NETview MS Computer WAN Router Server

(Ethernet) Control Center Mercury remote Mercury remote Mobile Data Mobile Data Figure 1-4. Integrated Mobile/Fixed Application 1.3.2 Wireless LAN The wireless LAN is a common application of the transceiver. It consists of a central control station (Access Point) and one or more associated Remote units, as shown in Figure 1-5. A LAN provides communications between a central WAN/LAN and remote Ethernet segments. The oper-

ation of the radio system is transparent to the computer equipment con-

nected to the transceiver. The Access Point is positioned at a location from which it communi-

cates with all Remote units in the system. Commonly, this is a high loca-

tion on top of a building or communications tower. Messages are exchanged at the Ethernet level. This includes all types of IP traffic. A Remote transceiver can only communicate over-the-air to an Access Point (AP). Peer-to-peer communications between Remotes can only take place indirectly via the AP. In the same fashion, an AP can only communicate over-the-air to associated Remote units. Exception: Two APs can communicate with each other off-the-air through their Ethernet connectors using a common LAN/WAN. Invisible place holder Remote LAN Remote LAN Remote LAN LAN Remote Access Point WAN/LAN Figure 1-5. Typical Wireless LAN 10 Mercury Reference Manual 05-4446A01, Rev. E 1.3.3 Point-to-Point LAN Extension A point-to-point configuration (Figure 1-6) is a simple arrangement consisting of an Access Point and a Remote unit. This provides a com-

munications link for transferring data between two locations. Invisible place holder Access Point Remote LAN/WAN LAN Figure 1-6. Typical Point-to-Point Link 1.3.4 Serial Radio Network Connectivity The transceiver provides a path for serial devices to migrate to IP/Ethernet systems. Many radio networks in operation today still rely on serial networks at data rates of 9600 bps or less. These networks can use the transceiver as a means to continue using the serial service, while allowing the infrastructure to migrate to an IP format. A Remote transceiver with its serial port connected to a GE MDS serial-based radio, such as the MDS x790/x710, MDS TransNET and others, provides a path for bringing the data from the older radio into the IP/Ethernet environment of a Mercury-based system. Invisible place holder Serial Conn. NETWORK ROUTER Remote Serial MDS 4790 Master ROUTER HUB Access Point Serial Conn. Remote Serial MDS 9790 Master NMS Control Point SCADA Host Modbus/IP MDS 4710 Remote MDS 4710 Remote MDS 9710 Remote MDS 9710 Remote Serial Conn. MDS 9810 Remote Remote Serial MDS 9810 Master MDS 9810 Remote Figure 1-7. Backhaul Network Serial Device Serial Device Serial Device Serial Device Serial Device Serial Device 1.3.5 Multiple Protocols and/or Services Prior to the introduction of Ethernet/IP-based radios, two radios were often used to service two different types of devices (typically connected 05-4446A01, Rev. E Mercury Reference Manual 11 to different SCADA hosts). A Mercury radio provides this capability using a single remote unit. The units serial port can be connected via IP to different SCADA hosts, transporting different (or the same) proto-

cols. Both data streams are completely independent, and the transceiver provides seamless simultaneous operation as shown in Figure 1-8. Invisible place holder Remote Serial RTU EIA-232 SCADA Host Modbus/IP HUB HUB WAN ROUTER HUBHUB NETview SCADA Host Total Flow Access Point Access Point Remote Serial Remote Serial Flow Meter EIA-232 EIA-232 EIA-232 EIA-232 EIA-232 Serial Device Serial Device Serial Device Serial Device Figure 1-8. Multiple Protocol Network By using a single radio, the cost of deployment is cut in half. Beyond requiring only one radio instead of two, the biggest cost reduction comes from using half of the required infrastructure at the remote site: one antenna, one feedline, one lightning protector and ancillary hardware. Other cost reductions come from the system as a whole, such as reduced management requirements. And above all, the radio provides the poten-

tial for future applications that run over Ethernet and IP, such as video for remote surveillance. 1.3.6 Wireless LAN with Mixed Services The transceiver is an excellent solution for a long-range industrial wire-

less LAN. It offers several advantages over commercial solutions, pri-

marily improved performance over extended distances. The rugged construction of the radio and its extended temperature range make it an ideal solution even in harsh locations. In extreme environments, a simple NEMA enclosure is sufficient to house the unit. The transceiver trades higher speed for longer range. Commercial 802.11a/b/g solutions are designed to provide service to relatively small areas such as offices, warehouses and homes. They provide high data rates but have limited range. The Mercury transmits at a higher power level, uses a different frequency band, has higher sensitivity, and a nar-

12 Mercury Reference Manual 05-4446A01, Rev. E rower channel to concentrate the radio energy, reaching farther dis-

tances. It is designed for industrial operation from the ground up. IP-based devices that may be used with the transceiver include new, powerful Remote Terminal Units (RTUs) and Programmable Logic Controllers (PLCs). These, as well as other devices, may be used in applications ranging from SCADA/telemetry monitoring, web-based video, security monitoring, and Voice over IP. Figure 1-9 shows a typ-

ical wireless IP network. Invisible place holder Remote Bridge IP Camera Access Point Remote Bridge IP/Ethernet IP/Ethernet IP/Ethernet NMS Control Point SCADA Host Modbus/IP Printer Figure 1-9. Extended-Range LAN with Mixed Applications 1.3.7 Upgrading Older Wireless Network with Serial Interfaces Millions of wireless data products have been installed in the last two decades for licensed and license-free operation, many of them manufac-

tured by GE MDS. There are several ways that these systems can benefit from incorporating Mercury equipment. The chief advantages are inter-

face flexibility (serial and Ethernet in one unit), and higher data throughput. By taking advantage of its built-in serial and Ethernet inter-

faces, the transceiver is well suited to replace leased lines, dial-up lines, or existing multiple address data transceivers. Replacing Legacy Wireless Products In most cases, legacy radio transceivers supporting serial-interface equipment can be replaced with Mercury transceivers. Legacy equip-

ment can be connected to the transceiver through the COM1 port with a DB-25 to DB-9 cable wired for EIA-232 signaling. The COM1 port acts as a Data Communications Equipment (DCE) port. 05-4446A01, Rev. E Mercury Reference Manual 13 NOTE: Several previous GE MDS-brand products had non-standard signal lines on their interface connectors (for example, to control sleep functions and alarm lines). These special func-

tions are not provided nor supported by the Mercury trans-

ceiver. Consult equipment manuals for complete pinout information. 1.4 NETWORK DESIGN CONSIDERATIONS 1.4.1 Extending Network Coverage with Repeaters What is a Repeater System?

A repeater works by re-transmitting data from outlying remote sites to the Access Point, and vice-versa. It introduces some additional end-to-end transmission delay but provides longer-range connectivity. In some geographical areas, obstacles can make communications diffi-

cult. These obstacles are commonly large buildings, hills, or dense foliage. These obstacles can often be overcome with a repeater station. Option AUsing two transceivers to form a repeater station

(back-to-back repeater) Although the range between fixed transceivers can be up to 40 km (25 miles) over favorable terrain, it is possible to extend the range consider-

ably by connecting two units together at one site in a back-to-back fashion, creating repeater as shown in Figure 1-10. Use this arrangement whenever the objective is to utilize the maximum range between sta-

tions. In this case, using high-gain Yagi antennas at each location pro-

vides more reliable communications than their counterparts omnidirectional antennas. Invisible place holder REPEATER Access Point Access Point Ethernet Crossover Cable T O - P O I N T L I N K P O I N T -

Remote LAN/WAN Remote LAN Remote LAN Remote LAN Figure 1-10. Typical LAN with a Repeater Link Two transceivers may be connected back-to-back through the LAN ports to form a repeater station. If the transceivers are connected directly to each other, you must use an Ethernet cross-over cable. This configu-

Overview 14 Mercury Reference Manual 05-4446A01, Rev. E Antennas Network Name TDD Sync Mode ration is sometimes required in a network that includes a distant Remote that would otherwise be unable to communicate directly with the Access Point station due to distance or terrain. The geographic location of a repeater station is especially important. Choose a site that allows good communication with both the Access Point and the outlying Remote site. This is often on top of a hill, building, or other elevated terrain from which both sites can be seen by the repeater station antennas. A detailed discussion on the effects of terrain is given in Section 5.1.2, Site Selection (beginning on Page 164). The following paragraphs contain specific requirements for repeater systems. Two antennas are required at this type of repeater stationone for each radio. You must take measures to minimize the chance of interference between these antennas. One effective technique for limiting interfer-

ence is to employ vertical separation. In this arrangement, assuming both antennas are vertically polarized, one antenna is mounted directly over the other, separated by at least 10 feet (3 meters). This takes advan-

tage of the minimal radiation exhibited by most antennas directly above and below their driven elements. Another interference reduction technique is to cross-polarize the repeater antennas. If one antenna is mounted for polarization in the ver-

tical plane, and the other in the horizontal plane, an additional 20 dB of attenuation is achieved. The corresponding stations should use the same antenna orientation when cross-polarization is used. The two radios that are wired together at the repeater site must have dif-

ferent network names. For information on how to set or view the net-

work names, see STEP 3: CONNECT PC TO THE TRANSCEIVER on Page 25. To avoid interference between the two APs that form a repeater station, they should be synchronized so that they will transmit at the same time and receive at the same time. This eliminates the possibility of one AP transmitting while another is trying to receive. This can be accomplished by setting the TDD Sync Mode parameter in the Frequency Configuration menu to GPS Required. See Frequency Control Menu on Page 67 for details. Option BUsing the AP as a Store-and-Forward Packet Repeater You can extend a wireless network by using the Access Point as a repeater to re-transmit the signals of all stations in the network. (See Figure 1-11 on Page 16.) 05-4446A01, Rev. E Mercury Reference Manual 15 Invisible place holder Remote LAN/WAN Access Point Remote REPEATER Remote LAN LAN Remote LAN Figure 1-11. Typical Store-and-Forward Repeater Arrangement As with the conventional repeater described in Option 1 above, the loca-

tion of a store and forward repeater is also important. A site must be chosen that allows good communication with both the Access Point and the outlying Remote site. This can be on the top of a hill, building, or other elevated terrain from which all sites can be seen by the repeater station antenna. A detailed discussion on the effects of terrain is given in Section 5.1.2, Site Selection (beginning on Page 164). 1.4.2 Protected Network Operation using Multiple APs Although GE MDS transceivers have a very robust design and have undergone intensive testing before being shipped, it is possible for iso-

lated failures to occur. In mission-critical applications, down time can be virtually eliminated by using some, or all, of the following configu-

rations:

In a point-to-multipoint scenario, the Access Point services multiple remotes. A problem in the Access Point will have an effect on all remotes, since none will have access to the network. When operation of the network does not tolerate any down time, it is possible to set up a protected configuration for the Access Point to greatly reduce the possi-

bility of this occurrence. Two or more Access Points can be configured identically, each with its own independent antenna. In this scenario, Remotes will associate with one of the available Access Points. In case of a failure of that AP, the Remotes will quickly associate with another Access Point, re-estab-

lishing connectivity to the end devices. Because only one Access Point operates at any given time, collisions between APs is not possible. 1.4.3 Collocating Multiple Radio Networks Many networks can operate in relatively close physical proximity to one another provided reasonable measures are taken to assure the radio signal of one Access Point is not directed at the antenna of the second Access Point. 16 Mercury Reference Manual 05-4446A01, Rev. E Co-Location for Multiple Networks The Network Name and the Association Process The Network Name is the foundation for building individual radio net-

works. Remotes in a network with the same network name as an Access Point (AP) unit are associated with that AP. The use of a different Network Name does not guarantee an interfer-

ence-free system. It does, however, assure that only data destined for a unique network is passed through to that network. It may be desirable to co-locate Access Points at one location to take advantage of an excellent location that can serve two independent net-

works. Configure each network with a unique Network Name, and install each APs antenna with at least 10 feet of vertical separation to minimize RFI. To co-locate APs, configure them with Time Division Duplex (TDD) Sync set to GPS Required. Configure all APs that are within range of each other with the same pattern, but with a unique Hop Pattern Offset. For more information, see Frequency Control Menu on Page 67. NOTE: Transceivers are shipped with the Network Name set to MDS-Mercury as a factory default. Can radio frequency interference (RFI) disrupt my wireless network?

When multiple radio networks operate in close physical proximity to other wireless networks, individual units may not operate reliably under weak signal conditions and may be influenced by strong radio signals on adjacent bands. This radio frequency interference cannot be predicted with certainty, and can only be determined by experimentation. If you need to co-locate two units, start by using the largest possible vertical antenna separation between the two AP antennas on the same support structure. If that does not work, consult with your factory representative about other techniques for controlling radio frequency interference between the radios. (See A Word About Radio Interference on Page 170 for more details.) 1.5 GE MDS CYBER SECURITY SUITE Today, the operation and management of an enterprise is increasingly dependent on electronic information flow. An accompanying concern becomes the cyber security of the communication infrastructure and the security of the data itself. 05-4446A01, Rev. E Mercury Reference Manual 17 The transceiver is capable of dealing with many common security issues. Table 1-2 profiles security risks and how the transceiver pro-

vides a solution for minimizing vulnerability. Table 1-2. Security Risk Management Security Vulnerability Unauthorized access to the backbone network through a foreign remote radio Rogue AP, where a foreign AP takes control of some or all remote radios and thus remote devices Dictionary attacks, where a hacker runs a program that sequentially tries to break a password. Denial of service, where Remote radios could be reconfigured with bad parameters, bringing the network down. Airsnort and other war-driving hackers in parking lots, etc. GE MDS Cyber Security Solution IEEE 802.1x device authentication Approved Remotes List (local) Only those remotes included in the AP list will associate IEEE 802.1x device authentication Approved AP List A remote will only associate to those APs included in its local authorized list of APs Failed-login lockdown After five tries, the transceiver ignores login requests for 5 minutes. Critical event reports (traps) are generated as well. Remote login with SSH or HTTPS Local console login Disabled HTTP and Telnet to allow only local management services Operation is not interoperable with standard 802.11 wireless cards The transceiver cannot be put in a promiscuous mode Proprietary data framing Eavesdropping, intercepting messages AES-128 encryption Unprotected access to configuration via SNMPv1 Intrusion detection Implement SNMPv3 secure operation Provides early warning via SNMP through critical event reports

(unauthorized, logging attempts, etc.) Unauthorized AP MAC address detected at Remote Unauthorized Remote MAC address detected at AP Login attempt limit exceeded

(Accessed via: Telnet, HTTP, or local) Successful login/logout

(Accessed via: Telnet, HTTP, or local) 18 Mercury Reference Manual 05-4446A01, Rev. E 1.6 ACCESSORIES The transceiver can be used with one or more of the accessories listed in Table 1-3. Contact the factory for ordering details. Table 1-3. Accessories Accessory Description AC Power Adapter Kit Omni-

Directional Antennas Yagi Antenna

(Directional) A small power supply module designed for continuous service. UL approved. Input:

120/220; Output: 13.8 Vdc @ 2.5 A Rugged antennas well suited for use at Access Point installations. Consult with your factory Sales Representative for details Rugged antennas well suited for use at fixed Remote sites. Consult with your factory Sales Representative for details. GPS Receiving Antennas A variety of fixed and mobile GPS antennas

(active and passive) are available. Consult with your factory Sales Representative for details. TNC Male-to-N Female Adapter TNC Male-to-N Female Adapter Cable Ethernet RJ-45 Crossover Cable (CAT5) 2-Pin Power Plug Ethernet RJ-45 Straight-thru Cable (CAT5) EIA-232 Shielded Data Cable One-piece RF adaptor plug. Short length of coaxial cable used to connect the radios TNC antenna connector to a Type N commonly used on large diameter coaxial cables. Cable assembly used to cross-connect the Ethernet ports of two transceivers used in a repeater configuration.

(Cable length 3 ft./1M) Mates with power connector on transceiver. Screw terminals provided for wires, threaded locking screws to prevent accidental disconnect. Cable assembly used to connect an Ethernet device to the transceiver. Both ends of the cable are wired identically.

(Cable length 3 ft./1M) Shielded cable terminated with a DB-25 male connector on one end, and a DB-9 female on the other end. Two lengths available (see part numbers at right). EIA-232 Shielded Data Cable Shielded cable terminated with a DB-9 male connector on one end, and a DB-9 female on the other end, 6 ft./1.8m long. GE MDS Part No. 01-3682A02

97-1677A161 97-1677A159

(3 ft./1m) 97-1677A160

(6 ft./1.8m) 97-1870A21 73-1194A39 97-1870A20 97-3035L06

(6 ft./1.8m) 97-3035L15

(15 ft./4.6m) 97-1971A03 Flat-Surface Mounting Brackets &

Screws Brackets: 2 x 3 plates designed to be screwed onto the bottom of the unit for surface-mounting the radio. 82-1753-A01 Bracket screws: 6-32/1/4 with locking adhesive.

(Industry Standard MS 51957-26) 70-2620-A01 Fuse Internal fuse, 5.0 Ampere 29-1784A04 05-4446A01, Rev. E Mercury Reference Manual 19 Table 1-3. Accessories (Continued) Accessory Description DIN Rail Mounting Bracket Bracket used to mount the transceiver to standard 35 mm DIN rails commonly found in equipment cabinets and panels. COM1 Interface Adapter DB-25(F) to DB-9(M) shielded cable assembly

(6 ft./1.8 m) for connection of equipment or other EIA-232 serial devices previously connected to legacy units. (Consult factory for other lengths and variations.) GE MDS Part No. 03-4022A03 97-3035A06 Bandpass Filter Antenna system filter that helps eliminate interference from nearby paging transmitters. 20-2822A02 Ethernet Surge Suppressor Surge suppressor for protection of Ethernet port against lightning. 29-4018A01 20 Mercury Reference Manual 05-4446A01, Rev. E 2 TABLETOP EVALUATION AND TEST SETUP 2 Chapter Counter Reset Paragraph Contents 2.1 OVERVIEW ........................................................................... 23 2.2 STEP 1CONNECT THE ANTENNA PORTS...................... 23 2.3 STEP 2CONNECT THE PRIMARY POWER ..................... 24 2.4 STEP 3CONNECT PC TO THE TRANSCEIVER............... 25 2.5 STEP 4REVIEW TRANSCEIVER CONFIGURATION ....... 25 2.5.1 Getting Started ....................................................................... 25 2.5.2 Procedure ............................................................................... 25 2.5.3 Basic Configuration Defaults .................................................. 25 2.6 STEP 5CONNECT LAN OR SERIAL DATA EQUIPMENT. 26 2.6.1 Option Set 1 Connectors ........................................................ 28 2.7 STEP 6CHECK FOR NORMAL OPERATION ................... 29 05-4446A01, Rev. E Mercury Reference Manual 21 22 Mercury Reference Manual 05-4446A01, Rev. E 2.1 OVERVIEW GE MDS recommends that you set up a tabletop network to verify the basic operation of the transceivers. This allows experimenting with net-

work designs, configurations, or network equipment in a convenient location. This test can be performed with any number of radios. When you are satisfied that the network is functioning properly in a benchtop setting, perform the field installation. Complete information for field installation, including mounting dimensions and antenna selec-

tion, is provided in INSTALLATION PLANNING on Page 163. NOTE: It is important to use a Network Name that is different from any currently in use in your area during the testing period. To simulate data traffic over the radio network, connect a PC or LAN to the Ethernet port of the Access Point and PING each transceiver several times. 2.2 STEP 1: CONNECT THE ANTENNA PORTS Figure 2-1 shows the tabletop arrangement. Connect the antenna ports of each transceiver as shown. This provides stable radio communica-

tions between each unit and prevents interference to nearby electronic equipment. Invisible place holder Remote Remote Remote POWER ATTENUATORS Fixed or adjustable 2W Minimum Rating Access Point COMPUTER POWER DIVIDER NON-RADIATING ATTENUATORS Install on unused divider ports (if any) 2W Minimum Rating Figure 2-1. Typical Setup for Tabletop-Testing of Radios 05-4446A01, Rev. E Mercury Reference Manual 23 NOTE: Use attenuation between all units in the test setup. The amount of attenuation required depends on the number of units tested and the desired signal strength (RSSI) at each transceiver during the test. In no case should a signal greater than 50 dBm be applied to any transceiver in the test setup. GE MDS recom-

mends an RF power output level of +20 dBm from the AP. Remote power is not setable. (See Radio Conguration Menu on Page 65.) 2.3 STEP 2: CONNECT THE PRIMARY POWER The primary power at the transceivers power connector must be within 10.530 Vdc and be capable of continuously providing 30 Watts. Typ-

ical power consumption for 13.8 Vdc and 24 Vdc operation are listed in SPECIFICATIONS on Page 178. A Phoenix two-pole power connector with screw-terminals is provided with each unit. Strip the wire leads to 6 mm (0.25"). Be sure to observe proper polarity with the positive lead (+) on the left and negative () on the right, as shown in Figure 2-2. NOTE: The transceiver typically requires about 30 seconds to power up, and might require several minutes to associate with another unit, if GPS is required for time synchronization. GPS is required for all configurations except when Free Run single-channel (non-frequency hopping) operation is used, which might be possible in some low-interference environments. CAUTION POSSIBLE EQUIPMENT DAMAGE Only use the transceiver with negative-ground power systems. Make sure the polarity of the power source is correct. Invisible place holder Figure 2-2. Power Connector

(Polarity: Left +, Right ) 24 Mercury Reference Manual 05-4446A01, Rev. E 2.4 STEP 3: CONNECT PC TO THE TRANSCEIVER Connect a PCs Ethernet port to the LAN port using an Ethernet cross-

over cable. The LAN LED should light. Alternatively, you can use a serial cable to connect to the COM1 port (Figure 2-3 on Page 27). 2.5 STEP 4: REVIEW TRANSCEIVER CONFIGURATION 2.5.1 Getting Started Start by logging into the Access Point radio. This is done first because the Remotes are dependent on the APs beacon signal to achieve an associated state. Once the Access Point is up and running, move the computer connection to each of the Remote units, log-in at each unit, review their configura-

tion, set their IP addresses, Network Name, and frequency configura-

tion, then wait for each AP to achieve an associated state. With all units associated, you will be ready to connect and test your data services. 2.5.2 Procedure The following is a summary of the configuration procedure that must be done on each unit in the system. Key parameters are shown on the Embedded Management System overview (Figure 3-1 on Page 34). A lists of parameters is located in two tablesTable 4-5 on Page 154 and Table 4-7 on Page 156. Detailed information on using the Management System can be found in INTRODUCTION on Page 33. NOTE: The Management System supports the use of configuration files to help consistently configure multiple units. These are explained in Conguration Scripts Menu on Page 131. 2.5.3 Basic Configuration Defaults Table 2-1 provides a selection of key operating parameters, their range, and default values. All of these are accessible through a terminal emu-

lator connected to the COM1 serial port or through a Web browser con-

nected to the LAN port (see Figure 5-1 on Page 163 for hookup). NOTE: Access to the transceivers Management System and changes to all parameters requires entering a security password. 05-4446A01, Rev. E Mercury Reference Manual 25 Table 2-1. Basic Configuration Defaults Item Network Name Menu Location Main Menu>>

Radio Configuration>>

Network Name IP Address RF Output Power Unit Password Main Menu>>

Network Configuration>>

IP Address Main Menu>>

Radio Configuration>>

Transmit Power Main Menu>>

Device Information>>

User Password Default MDS-Mercury 192.168.1.1 Values/Range 115 alphanumeric characters Case-sensitive;

can be mixed case Contact your network administrator

+29 dBm (900 model)

+23 dBm (3650 model) AP: -30 to +29 dBm RM: 0 to +29 dBm admin

(lower case) 113 alphanumeric characters Case-sensitive;

can be mixed case For benchtop evaluation, configure:

Frequency Mode = Single Channel Single Frequency Channel = 0 RF Bandwidth = 1.75 TDD Sync = Free Run For more information on configuring these parameters, see Frequency Control Menu on Page 67. A unique IP address and subnet are required to access all IP-based man-

agement interfaces (telnet, SSH, SNMP, and Web), either through the LAN port or remotely over-the-air. 2.6 STEP 5: CONNECT LAN OR SERIAL DATA EQUIPMENT Connect a local area network to the LAN port or a serial device to the COM1 (DCE) port. The LAN port supports any Ethernet-compatible equipment. This includes devices that use Internet Protocol (IP). Figure 2-3 on Page 27 shows the interface connectors on the front panel of the standard transceiver (Remote). The Option Set 1 Remote connec-

tors are shown in Figure 2-4 on Page 28. NOTE: The use of shielded Ethernet cable is recommended for connection to the radios ETH port. The radio meets regulatory emission standards without shielded cable, but shielding reduces the possibility of interference in sensitive environ-

ments, and is in keeping with good engineering practice. 26 Mercury Reference Manual 05-4446A01, Rev. E LAN PORT Invisible place holder LED INDICATOR PANEL COM1 SERIAL PORT DC POWER INPUT

(1030 VDC, 2.5A) GPS ANTENNA CONNECTION TX/RX1 ANTENNA PORT RX2 ANTENNA PORT Figure 2-3. Transceiver Interface Connectors

(Standard unit shown; See Figure 2-4 on Page 28 for Option Set 1 unit) LED INDICATOR PANELDisplays the basic operating status of the transceiver. See section 2.7 on Page 29 for detailed informa-

tion. COM1 SERIAL PORT DB-9 connector used for management of the transceiver with a connected PC. INTRODUCTION on Page 33 provides complete connection details. LAN PORTConnection point for Ethernet Local Area Net-

work. The connector has integrated LEDs to indicate signal activity as follows: A steady green LED indicates that a link has been achieved; a flashing green LED indicates data activity; and a yellow LED indicates 100 Mbps operation. PWR DC power connection for the transceiver. Power source must be 10 Vdc to 30 Vdc, negative ground, and capable of pro-

viding at least 25 watts. GPS ANTENNA PORT Coaxial connector (SMA-type) for connection of a GPS receiving antenna. Provides 3.5 Vdc output for compatibility with powered (active) GPS antennas. The GPS receiving antennas gain must be 16 dBi or less. NOTE: GPS functionality is required on all Access Points and Remotes except when Free Run single-channel (non-frequency hopping) operation is used, which might be possible in some low-interference environments. RX2 ANTENNA PORT Coaxial connector (TNC-type) for attachment of a second receiving antenna used in space diver-

sity arrangements. TX/RX1 ANTENNA PORT Coaxial connector (TNC-type) for attachment of the main station antenna (transmit and receive). 05-4446A01, Rev. E Mercury Reference Manual 27 2.6.1 Option Set 1 Connectors Figure 2-4 shows the interface connectors on the front panel of the Option Set 1 Remote transceiver. NOTE: The use of shielded Ethernet cable is recommended for connection to the radios ETH port. The radio meets regulatory emission standards without shielded cable, but shielding reduces the possibility of interference in sensitive environ-

ments, and is in keeping with good engineering practice. Invisible place holder Figure 2-4. Option Set 1 Transceiver Interface Connectors LED INDICATOR PANELDisplays the basic operating status of the transceiver. See section 2.7 on Page 29 for detailed informa-

tion. COM1 SERIAL PORT DB-9 connector used for management of the transceiver with a connected PC. INTRODUCTION on Page 33 provides complete connection details. LAN PORTSConnection point for Ethernet Local Area Net-

work. The connectors have integrated LEDs to indicate signal activity as follows: A steady green LED indicates that a link has been achieved; a flashing green LED indicates data activity; and a yellow LED indicates 100 Mbps operation. PWR DC power connection for the transceiver. Power source must be 10 Vdc to 30 Vdc, negative ground, and capable of pro-

viding at least 25 watts. 28 Mercury Reference Manual 05-4446A01, Rev. E GPS ANTENNA PORT Coaxial connector (SMA-type) for connection of a GPS receiving antenna. Provides 3.5 Vdc output for compatibility with powered (active) GPS antennas. Do not short this connector, as you might cause damage to the internal power supply. The GPS receiving antennas gain must be 16 dBi or less. NOTE: GPS functionality is required on all Access Points and Remotes except when Free Run single-channel (non-frequency hopping) operation is used, which might be possible in some low-interference environments. WiFi ANTENNA PORT Coaxial connector (SMA-type) for attachment of a WiFi antenna. WiFI is typically used for short range wireless communication at the transceiver site or within a small area around the site. RX2 ANTENNA PORT Coaxial connector (TNC-type) for attachment of a second receiving antenna used in space diver-

sity arrangements. TX/RX1 ANTENNA PORT Coaxial connector (TNC-type) for attachment of the main station antenna (transmit and receive). 2.7 STEP 6: CHECK FOR NORMAL OPERATION Once the data equipment is connected, you can check the transceiver for normal operation. Observe the LEDs on the top cover for the proper indications. In a nor-

mally operating system, you will see the following LED indications within 45 seconds of start-up:

PWRLit continuously LINKOn, or blinking intermittently to indicate traffic flow LANOn, or blinking intermittently to indicate traffic flow Figure 2-5 shows a close-up view of the transceivers LED Indicator panel. Table 2-2 provides details on each LED function. Invisible place holder 05-4446A01, Rev. E Mercury Reference Manual 29 Figure 2-5. LED Indicator Panel If the radio network seems to be operating properly based on observa-

tion of the units LEDs, use the PING command to verify the link integ-

rity with the Access Point. Table 2-2. Transceiver LED Functions LED Label PWR LAN*

COM1

(MGT System) GPS LINK

(Access Point) LINK

(Remote) USB Activity ON Blinking OFF ON Blinking OFF Blinking OFF ON Blinking OFF ON OFF ON OFF ON OFF Indication Primary power (DC) present Unit in Alarmed state Primary power (DC) absent LAN detected Data TX/RX LAN not detected, or excessive traffic present Data TX/RX No data activity Internal GPS receiver is synchronized with the satellite network. AP modem is synchronizing with the GPS timing. Internal GPS receiver is not synchronized with the satellite network. Unit is operational Not transmitting. Usually occurs while waiting for GPS sync. Associated to AP Not associated with AP USB activity on either port No USB activity

* The LAN connector has two integrated LEDs to indicate signal activity as follows: A steady green LED indicates that a link has been achieved;

a flashing green LED indicates data activity, and a yellow LED indicates 100 Mbps operation. 30 Mercury Reference Manual 05-4446A01, Rev. E 3 DEVICE MANAGEMENT 3 Chapter Counter Reset Paragraph Contents 3.1 INTRODUCTION .....................................................................33 3.1.1 Differences in the User Interfaces ............................................33 3.2 ACCESSING THE MENU SYSTEM ........................................35 3.2.1 Methods of Control ...................................................................36 3.2.2 PC Connection and Log In Procedures ...................................36 3.2.3 Navigating the Menus ..............................................................40 3.3 BASIC OVERVIEW OF OPERATION......................................42 3.3.1 Starting Information Screen .....................................................42 3.3.2 Main Menu ...............................................................................43 3.4 CONFIGURING NETWORK PARAMETERS ..........................45 3.4.1 Network Configuration Menu ...................................................45 3.4.2 Ethernet Port Configuration Menu ...........................................56 3.4.3 Bridge Configuration ................................................................58 3.4.4 SNMP Agent Configuration ......................................................58 3.4.5 AP Location Push Config Menu ...............................................60 3.4.6 SNTP Server Configuration ......................................................64 3.5 RADIO CONFIGURATION ......................................................65 3.5.1 Radio Configuration Menu .......................................................65 3.5.2 Serial Port Configuration ..........................................................76 3.6 MODBUS / TCP SERVER CONFIGURATION ........................88 3.6.1 Modbus/TCP in Mercury TransceiversAn Overview .............88 3.6.2 Menu Selections .......................................................................89 3.7 SECURITY CONFIGURATION MENU ....................................92 3.7.1 Device Security Menu ..............................................................93 3.7.2 Wireless Security Menu ...........................................................95 3.7.3 IEEE 802.1x Device Authentication .........................................97 3.7.4 Manage Certificates .................................................................99 3.8 REDUNDANCY CONFIGURATION (AP ONLY)......................102 3.9 GPS CONFIGURATION (REMOTE ONLY).............................107 05-4446A01, Rev. E Mercury Reference Manual 31 3.10 DEVICE INFORMATION MENU............................................109 3.11 PERFORMANCE INFORMATION MENU .............................110 3.12 MAINTENANCE/TOOLS MENU............................................123 3.12.1 Installing Firmware via TFTP ................................................129 3.12.2 Auto Firmware Upgrade Menu (AP Only) ..............................138 3.13 PERFORMANCE OPTIMIZATION ........................................140 3.13.1 Proper OperationWhat to Look For ....................................143 32 Mercury Reference Manual 05-4446A01, Rev. E 3.1 INTRODUCTION The transceivers embedded management system is accessible through the COM1 (serial) port, the LAN (Ethernet) port, and using over-the-air Ethernet. Telnet, SSH, HTTP/HTTPS, and SNMP are the Ethernet-based interfaces. Essentially, the same capabilities are avail-

able through any of these paths. For support of SNMP software, a set of MIB files is available for down-

load from the GE MDS Web site at www.GEmds.com. An overview of SNMP commands can be found at SNMP Agent Conguration section on Page 58 of this manual. The transceivers Management System and its functions are divided into seven functional groups as listed below. Section 3.3, BASIC OVERVIEW OF OPERATION (beginning on Page 42) Section 3.4, CONFIGURING NETWORK PARAMETERS

(beginning on Page 45) Section 3.5, RADIO CONFIGURATION (beginning on Page 65) Section 3.7, SECURITY CONFIGURATION MENU (beginning on Page 92) Section 3.13, PERFORMANCE OPTIMIZATION (beginning on Page 140) Section 3.12, MAINTENANCE/TOOLS MENU (beginning on Page 123) Each of these sections has a focus that is reflected in its heading. The section you are now reading provides information on connecting to the Management System, how to navigate through it, how it is structured, and how to perform top-level configuration tasks. Figure 3-1 on Page 34 shows a top-level view of the Management System (MS). 3.1.1 Differences in the User Interfaces Although there are slight differences in navigation among the user inter-

faces, the content is very similar. You will notice a few differences in capabilities as the communications tool is driven by limitations of the access channel. Figure 3-2 and Figure 3-3 on Page 35 show examples of the Starting Information Screen as seen through a console terminal and a web-browser, respectively. 05-4446A01, Rev. E Mercury Reference Manual 33 l

s o o T e c n a n e t n a M i i g n m m a r g o r p e R s t p i r c S

. g i f n o C y t i l i t U g n P i s e d o C

. t h u A

. t n e e r c S n o i t a m r o f n I g n i t r a t S

) s u t a t S y n O

d a e R l

U N E M N A M I e c n a m r o f r e P n o i t a m r o f n I e c i v e D n o i t a m r o f n I

) y c n a d n u d e R P A

n o i t a r u g i f n o C y t i r u c e S n o i t a r u g i f n o C i o d a R n o i t a r u g i f n o C e t a D e m T i s c i t s i t t a S t e k c a P r e b m u N l a i r e S s r e g g i r T t n e v E k w N t y t i r u c e S s s e e r i l W g o L t n e v E l e d o M

. g i f n o C y c n a d n u d e R y t i r u c e S e c v e D i t t a S k w N s s e e r i l W s r e g g i r T t n e v E r w d H t t s u a S S P G e m i t p U s r e g g i r T t n e v E o d a R i n o i t a r u g i f n o C I S U D A R

. f i t r e C e g a n a M e m a N k r o w t e N r e w o P t i m s n a r T

) P A

. r w P e v e c e R i l o r t n o C

. q e r F g i f n o C t r o P t e n r e h E t n o i t a r u g i f n o C e g d i r B g i f n o C

. c f t n I

. k w N t k r o w t e N n o i t a r u g i f n o C

) P A

. g i f n o C t n e g A P M N S s t l f u a e D o t t e s e R

) M R

. t t a S o d a R i

. l t n I s n o i t p O

. g i f n o C

. d e R

. g i f n o C

. v d A

) M R

o f n I n o i t a c o L P A t s e T o d a R i d n e r T e c n a m r o f r e P t a m r o F e t a D r e v o h c t i w S e c r o F

. g i f n o C r e v r e S P T N S i s n o s r e V W F

. t R

. l d B e o s n o C e d a r g p U W F

t e s f f i O e m T C T U s e m a N e c v e D i l e o s n o C o t S P G m a e r t S

) M R S P G

n o i t a r u g i f n o C i P D U a v S P G d n e S s s e r d d A P I r e v r e S P D U S P G

. s l i a t e d r o f l t r o P P D U r e v r e S P D U S P G s n o a u n a M e c n e r e f e R e e S l i

. y n o w e v l e v e l

p o t s w o h s t r a h C l i t c e e s u n e m e m o s e k a m o t d e s u s i r a b e c a p S l e b a r u g i f n o c r e s u

e r a s m e t i u n e m l l a t o N l y n O l i t n o P s s e c c A

P A y n O e t o m e R

M R S E T O N Figure 3-1. Embedded Management SystemTop-Level Flowchart 34 Mercury Reference Manual 05-4446A01, Rev. E Figure 3-2. View of MS with a text-based program

(Console Terminal shownTelnet has similar appearance) Invisible place holder Figure 3-3. View of the MS with a Browser

(Selections at left provide links to the various menus) 3.2 ACCESSING THE MENU SYSTEM The radio has no external controls or adjustments. All configuration, diagnostics, and control is performed electronically using a connected PC. This section explains how to connect a PC, log into the unit, and gain access to the built-in menus. 05-4446A01, Rev. E Mercury Reference Manual 35 3.2.1 Methods of Control Access the units configuration menus in one of several ways:

Local ConsoleThis is the primary method used for the exam-

ples in this manual. Connect a PC directly to the COM1 port using a serial communications cable and launch a terminal com-

munications program such as HyperTerminal (found on most PCs by selecting Start>>Programs>>Accessories>>Communica-

tions>>HyperTerminal). This method provides text-based access to the units menu screens. Console control is a hardware-based technique, and is intended for local use only (maximum recom-

mended cable length of 50 ft./15 m). Telnet or SSH*Connect a PC to the units LAN port, either directly or via a network, and launch a Telnet session. This method provides text-based access to the units menu screens in a manner similar to a Local Console session. You can run Telnet sessions locally or remotely through an IP connection. Web Browser*Connect a PC to the units LAN port, either directly or via a network, and launch a web browser session (for example, Internet Explorer, Firefox, etc.). Enter the IP address of the device to be managed into the browsers address field. This method provides a graphical representation of each screen, just as you would see when viewing an Internet web site. The appearance of menu screens differs slightly from other methods of control, but the content and organization of screen items is similar. Web browser sessions may be run locally or remotely using an IP connection.

* When connecting directly to a radio, a crossover cable is required. When connecting using a network, switch, or router, a straight-through cable is required. 3.2.2 PC Connection and Log In Procedures The following steps describe how to access the radios menu system. These steps require a PC to be connected to the units COM1 or LAN port as shown in Figure 3-4 on Page 37. 36 Mercury Reference Manual 05-4446A01, Rev. E Invisible place holder Transceiver Transceiver To COM1 or LAN Port

(See Text) To COM1 or LAN Port

(see text) PC Running Terminal Session PC Running Terminal Session

(115,200 bps, 8N1)

(115,200 bps, 8N1) Figure 3-4. PC Configuration Setup 1. Connect a serial communications cable between the PC and the units COM1 port. If necessary, a cable may be constructed for this purpose as shown in Figure 3-5. DCE DB-9 MALE

(TO MDS PRODUCT) Invisible place holder DTE DB-9 FEMALE

(TO COMPUTER) Starting a Local Console Session

(Recommended for first-time log-in) RXD TXD GND 2 3 5 2 3 5 RXD TXD GND Figure 3-5. Serial Communications Cable (DB-9M to DB-9F)

(Maximum Recommended Cable Length 50 feet/15 meters) 2. Launch a terminal emulation program such as HyperTerminal and congure the program with the following settings:

115,200 bps data rate 8 data bits, no parity One stop bit, and no flow-control Use ANSI or VT100 emulation. TIP: The HyperTerminal communications program can be accessed on most PCs by selecting this menu sequence: Start>>Programs>>Accesso-

ries>>Communications>>HyperTerminal. NOTE: If the unit is powered-up or rebooted while connected to a terminal, you will see a series of pages of text information relating to the booting of the units processor. Wait for the log-in screen before proceeding. 3. Press the ENTER key to receive the login: prompt. 4. Enter the username (default username is admin). Press ENTER

. 05-4446A01, Rev. E Mercury Reference Manual 37 5. Enter your password (default password is admin). For security, your password keystrokes do not appear on the screen. Press ENTER

. NOTE: Passwords are case sensitive. Do not use punctuation mark characters. You may use up to 13 alpha-numeric characters. The unit responds with the Starting Information Screen (Figure 3-6). From here, you can review basic information about the unit or press G to proceed to the Main Menu. Invisible place holder Figure 3-6. Starting Information ScreenLocal Console Session Starting a Telnet Session NOTE: This method requires that you know the IP address of the unit beforehand. If you do not know the address, use the Local Console method (above) and access the Starting Information Screen. The address is displayed on this screen. 1. Connect a PC to the units LAN port, either directly with a crossover cable or via a network with a straight-through cable. The LAN LED lights to indicate an active connection. NOTE: When using Ethernet to access the unit, you might need to change your computers IP address to be on the same subnet as the radio. You can identify or verify the units IP address by using a Local Console session to communicate with the radio through its COM1 Port and viewing the Starting Information Screen. 2. Start the Telnet program on your computer, targeting the IP address of the unit to which you are connected, and press ENTER

. 38 Mercury Reference Manual 05-4446A01, Rev. E TIP: You can start a Telnet session on most PCs by selecting: Start>>Pro-

grams>>Accessories>>Command Prompt. At the command prompt window, type the word telnet, followed by the units IP address to receive the Telnet log in

(e.g., telnet 10.1.1.168). Press screen. ENTER NOTE: Never connect multiple units to a network with the same IP address. Address conflicts will result in improper operation. 3. Enter your username (default username is admin). Press ENTER

. Next, the Password: prompt appears. Enter your password (default password is admin). For security, your password keystrokes will not appear on the screen. Press ENTER

. Starting a Web Browser Session The unit responds with a Starting Information Screen (see Figure 3-6 on Page 38). From here, you can review basic informa-

tion about the unit or press G to proceed to the Main Menu. NOTE: Passwords are case sensitive. Do not use punctuation mark characters. You may use up to 13 alpha-numeric characters. NOTE: Web access requires that you know the IP address of the unit you are connecting to. If you do not know the address, start a Local Console session (see Starting a Local Console Session

(Recommended for rst-time log-in) on Page 37) and access the Starting Information Screen. The IP address is displayed on this screen. 1. Connect a PC to the units LAN port, either directly or using a network. If connecting directly, use an Ethernet crossover cable; if connecting using a network, use a straight-through cable. The LAN LED lights to indicate an active connection. 2. Launch a Web-browser session on your computer (i.e., Internet Explorer, Firefox, etc.). 3. Type the units IP address and press ENTER

. 4. A log-in screen is displayed (Figure 3-7 on Page 40) where you enter a user name and password to access the units menu system. Note that the default entries are made in lower case. (Default User Name: admin; Default Password: admin) 05-4446A01, Rev. E Mercury Reference Manual 39 Invisible place holder Figure 3-7. Log-in Screen when using a Web Browser NOTE: Passwords are case sensitive. Do not use punctuation mark characters. You may use up to 13 alpha-numeric characters. 5. Click OK. The unit responds with a startup menu screen similar to that shown in Figure 3-8. From here, you can review basic informa-

tion about the unit or click one of the menu items at the left side of the screen. Invisible place holder Figure 3-8. Starting Information ScreenWeb Browser Example 3.2.3 Navigating the Menus Via Terminal Telnet or SSH Sessions Recommended for first-time log-in Local Console, Telnet, and SSH sessions use multi-layered text menu systems that are nearly identical. To move further down a menu tree, you type the letter assigned to an item of interest. This takes you to an 40 Mercury Reference Manual 05-4446A01, Rev. E associated screen where settings may be viewed or changed. In most cases, pressing the menu tree. key moves the screen back one level in the ESCAPE In general, the top portion of menu screens show read-only information

(with no user selection letter). The bottom portion of the screen contains parameters you can select for further information, alteration of values, or to navigate to other submenus. NOTE: Early versions of PuTTY might not operate when using SSH to connect to the transceiver. The latest version (0.60 at the time of publication) does work with the transceivers internal server. Both the latest released and the latest development snapshot can be downloaded from:

www.chiark.greenend.org.uk/~sgtatham/putty/. When you arrive at a screen with user-controllable parameter fields, you select the menu item by pressing an associated letter on the keyboard. If there is a user definable value, the field will clear to the right of the menu item and you can type the value you wish to use. Follow this action by key to save the changes. If you make a mistake or pressing the change your mind before pressing the ESCAPE to restore the previous value. key, simply press ENTER ENTER In some cases, when you type a letter to select a parameter, you will see a prompt at the bottom of the screen that says Choose an Option. In these screens, press the keyboards selections. When the desired option appears, press the choose that selection. In some cases, you can change several parameters and then save them with a single keystroke. Use the cancel the action and restore the previous values. to step through the available key to key to SPACEBAR ESCAPE ENTER Logging Out Via Terminal Emulator or Telnet From the Main Menu screen, press Q to quit and terminate the session. NOTE: To maintain security, it is best to log-out of the menu system entirely when you are done working with it. If you do not log out, the session automatically ends after 10 minutes of inac-

tivity. Navigating via Web Browser Navigating with a Web browser is straightforward with a framed home page. The primary navigation menu is permanently located on the left-hand side of this page. Simply click the desired menu item to make it active. Logging Out Via Web Browser Click Logout in the left-hand frame of the browser window. The right-hand frame changes to a logout page. Follow the remaining instructions on this screen. 05-4446A01, Rev. E Mercury Reference Manual 41 NOTE: In the menu descriptions that follow, parameter options/range, and any default values are displayed at the end of the text between square brackets. Note that the default setting is always shown after a semicolon:

[available settings or range; default setting]

3.3 BASIC OVERVIEW OF OPERATION 3.3.1 Starting Information Screen Once you have logged into the Management System, the Starting Infor-

mation Screen (Figure 3-9) appears with an overview of the transceiver and its current operating conditions. Figure 3-9. Starting Information Screen

(AP screen shown; Remote similar, differences noted below) Device ModeOperating mode of the unit as it relates to the radio network. Device NameThis is a user-defined parameter that appears in the heading of all pages. (To change it, see Network Congura-

tion Menu on Page 45.) Current IP AddressUnits IP address [169.254.0.2]

Device StatusCondition of the units operation as follows:

InitializingThis is the first phase after boot-up. At Access Point:

OperationalUnit operating normally. SynchronizingUnit is waiting for the GPS receiver to obtain a satellite fix and for its internal clock to synchronize to the GPS timing signals. 42 Mercury Reference Manual 05-4446A01, Rev. E AlarmedThe unit has detected one or more alarms that have not been cleared. At Remote:

ScanningThe unit is looking for an Access Point beacon signal. RangingUnit is adjusting power, timing, and frequency with an AP. ConnectingThe unit has found a valid beacon signal for its network. AuthenticatingDevice is attempting device authentication. Associated The unit has successfully synchronized and associated with an Access Point. AlarmedThe unit is has detected one or more alarms that have not been cleared. NOTE: If an alarm is present when this screen is displayed, an A) appears to the left of the Device Status field. Pressing the A key on your keyboard takes you directly to the Current Alarms screen. Associated Remotes (AP Only)Indicates the number of Remotes that have achieved association with the AP. Connection Status (Remote Only)Indicates whether the Remote has an RF connection with an AP. Satellite Fix StatusIndicates whether internal GPS receiver has achieved synchronization with GPS satellite signals. UptimeElapsed time since the transceiver was last booted up. Firmware VersionVersion of firmware that is currently active in the unit. Hardware Version Hardware version of the transceivers printed circuit board. Serial NumberMake a record of this number. Provide this num-

ber when purchasing Authorization Codes to upgrade unit capa-

bilities in the future. (See Authorization Codes on Page 136.) 3.3.2 Main Menu The Main Menu (Figure 3-10/Figure 3-11) is the entry point for all user-controllable features. The transceivers Device Name appears at the top of this and all other screens as a reminder of the unit you are cur-

rently controlling. 05-4446A01, Rev. E Mercury Reference Manual 43

(AP menu shown, Remote similar; Differences noted in text below) Figure 3-10. Main Menu (AP) Figure 3-11. Main Menu (MDS 3650 Remote Only) Starting Information ScreenSelect this item to return to the Start-

ing Information screen described above. Network ConfigurationTools for configuring the data network layer of the transceiver. (See CONFIGURING NETWORK PARAMETERS on Page 45) Radio ConfigurationTools to configure the wireless (radio) layer of the transceiver. (See RADIO CONFIGURATION on Page 65) Serial Port ConfigurationMenus for tailoring the COM1 port for data mode operation (data only). (See Serial Port Congura-

tion on Page 76) 44 Mercury Reference Manual 05-4446A01, Rev. E Security ConfigurationTools to configure the security services available with the transceivers environment. (See SECURITY CONFIGURATION MENU on Page 92) Redundancy Configuration(AP Only) Allows setting of the cri-

teria for switchover in the event of loss of associated Remotes or excessive packet receive errors. GPS Configuration(Remote Only; not available on MDS 3650 model) View/set parameters related to GPS streaming location output. (See GPS CONFIGURATION (REMOTE ONLY) on Page 107) Device InformationTop level device fields such as model, serial number, date/time, etc. (See DEVICE INFORMATION MENU on Page 109) Performance InformationStatus information relating to the radio and data layers performance in the radio network.

(See PERFORMANCE INFORMATION MENU on Page 110) Maintenance/ToolsTools for upgrading firmware code and test-

ing major unit capabilities. (See MAINTENANCE/TOOLS MENU on Page 123) 3.4 CONFIGURING NETWORK PARAMETERS 3.4.1 Network Configuration Menu The Network Configuration Menu is the home of several parameters that you should review and set as necessary before placing a transceiver into service. Figure 3-12. Network Configuration Menu

(Standard radio) 05-4446A01, Rev. E Mercury Reference Manual 45 Figure 3-13. Network Configuration Menu

(Option Set 1 radio) Network Interface ConfigPresents a menu where you can view or set various parameters (VLAN Status, IP Configuration, and DHCP Server Configuration). Ethernet Port ConfigPresents a menu for defining the status of the Ethernet port (enabled or disabled), port follows association, and Ethernet filtering configuration. Detailed explanations of this menu are contained in Ethernet Port Conguration Menu on Page 56. Bridge ConfigurationView/set options for Ethernet Bridge oper-

ation. SNMP Agent ConfigView/set SNMP configuration parameters. See SNMP Agent Conguration on Page 58 for more infor-

mation. AP Location Info ConfigOn an AP this submenu allows for con-

figuring an AP to automatically download the AP Locations File to its associated Remotes. On a Remote this submenu allows for downloading an AP Locations File. See AP Loca-

tion Push Cong Menu on Page 60 for additional details. 802.11 ConfigurationPresents a submenu for configuring the radios internal WiFi module to be an Access Point for other WiFi devices (APs), to connect to a WiFi Access Point at another location (Station), or to connect directly to another WiFi device (Ad-Hoc). SNTP ServerAddress of SNTP server (RFC 2030) from which the transceiver will automatically get the time-of-day. You can also manually set the date and time. A Mercury unit tries to get the time and date from the SNTP server only if an IP address is configured. It will continue to retry every minute until it suc-

46 Mercury Reference Manual 05-4446A01, Rev. E ceeds. The transceivers use UTC (Universal Time Coordinated) with a configurable time offset. [0]

NOTE: The Mercury gets time of day data from the GPS receiver if the receiver gets a satellite fix. Network Interface Configuration Submenu Invisible place holder Figure 3-14. Network Interface Configuration Submenu VLAN StatusThis selection is used to enable or disable virtual LAN operation. For details, refer to VLAN Conguration Menu on Page 47. [enable, disabled; disabled]

IP ConfigurationThis selection presents a submenu for config-

uring the local IP address of the transceiver. Detailed explana-

tions are provided in the section titled IP Conguration Menu on Page 53. DHCP Server ConfigMenu for configuration of DHCP services by the Access Point. DHCP provides on-the-fly IP address assignments to other LAN devices, including Mercury Series units. For details, refer to DHCP Server Conguration (Data and Mgmt) on Page 50. VLAN Configuration Menu The VLAN Configuration menu (Figure 3-15) becomes active and vis-

ible when you enable VLAN Status on the Network Interface Configura-

tion Menu, and you press the Enter key. CAUTION:The VLAN Status parameter must be consistent at both the Access Point and Remote radios in order for data to flow correctly. Failure to do so might result in data not being trans-

ported correctly even when the radios are in an associated state and able to communicate over-the-air. 05-4446A01, Rev. E Mercury Reference Manual 47 About Virtual LAN in Mercury A VLAN is essentially a limited broadcast domain, meaning that all members of a VLAN receive broadcast frames sent by members of the same VLAN but not frames sent by members of a different VLAN. For more information, refer to the IEEE 802.1Q standard. The transceiver supports port-based VLAN at the Ethernet interface and over the air, according to the IEEE 802.1Q standard. When VLAN Status is enabled, the wireless port of both AP and Remote radios act, according to user configuration, as either a trunk port or access port. The Ethernet port of an Access Point radio is normally configured as a trunk port. This type of port expects incoming frames to have a VLAN ID tag and sends outgoing frames with a VLAN tag as well. The Ethernet port of a Mercury radio can be configured as an access port or as a trunk port. When the Ethernet port of a Mercury radio is configured as VLAN Access Port, the radio tags incoming traffic with a VLAN ID, and strips the tag before sending traffic out. This VLAN is known as the DATA VLAN. Additionally, a second VLAN is assigned for other traffic that is terminated at the radio, such as SNMP, TFTP, ICMP, Telnet, and so on. This is known as the MANAGEMENT VLAN. Traffic directed to the integrated terminal server that handles the serial ports is assigned to the DATA VLAN. When the Ethernet port of a remote radio is configured as a VLAN trunk, the radio expects all incoming Ethernet frames to be tagged, and passes all outgoing frames as received from the wireless link, with the unchanged VLAN tag. Network Interface Configuration SubmenuVLAN Items Invisible place holder Figure 3-15. VLAN Configuration Menu 48 Mercury Reference Manual 05-4446A01, Rev. E VLAN StatusDefines whether the radio handles Ethernet frames in extended 802.1Q mode or in normal mode in the Ethernet port. If configured with a trunk port, the Mercury passes all tagged traffic regardless of the VLAN ID. The Mer-

cury only uses the Data VLAN ID parameter when the ETH port is configured as an Access Port.

[enabled, disabled; disabled]

VLAN Ethport ModeDefines if the Ethernet port acts as a trunk port or as an access port. Auto mode defines the port as a trunk port in an AP, or an access port in a Remote radio.

[Auto, Trunk, Access; Auto]

Management VLAN IDDefines the VLAN ID for traffic directed to the radio itself, other than the terminal server process. This VLAN ID is used for filtering and for tagging purposes.

[1-4094; 2]

Data VLAN IDDefines the VLAN ID assigned to traffic directed to and from the Ethernet port and the terminal server process in the radio. This VLAN ID is used for filtering and tagging pur-

poses. [1-4094; 3]

Default Route IFDefines the VLAN that contains the default gateway in the radio. [MGMT, DATA; MGMT]

Management VLAN ModeApplies the VLAN tag to management frames. [Tagged, Native; Tagged]. Management VLAN Subnet ConfigPresents a screen where you can set the IP Address Mode, Static IP Address, and Static IP Netmask (see Figure 3-16 on Page 50). DHCP Server Config (Mgmt)Presents a screen where you can view or set the DHCP server status and address information for management functions (see Figure 3-17 on Page 51). Data VLAN Subnet ConfigPresents a screen where you can view or set the IP mode and address information (see Figure 3-19 on Page 52). DHCP Server Config (Data)Presents a screen where you can view or set DHCP server status and address information for data functions (see Figure 3-18 on Page 52). 05-4446A01, Rev. E Mercury Reference Manual 49 Management VLAN Subnet Configuration Menu Invisible place holder Figure 3-16. Management VLAN Subnet Configuration Menu NOTE: Changes to any of the following parameters while communi-

cating over the network (LAN or over-the-air) might cause a loss of communication with the unit you are configuring. You must re-establish communication using the new IP address. IP Address ModeDefines the source of the IP address of this device. Only static IP addressing mode is available when VLAN Status is enabled. [Static, Dynamic; Static]

Static IP AddressThe IPv4 local IP address. [192.168.1.1]

Static IP NetmaskThe IPv4 local subnet mask. This value is used when the radio attempts to send a locally initiated message, either from the terminal server, or from a management process.

[255.255.0.0]

The lower three lines of the screen (Current IP Address, Current IP Netmask, Current IP Gateway) show the current addressing configured at the trans-

ceiver. Current IP Gateway only displays on this screen if Default Route IF on the Network Interface Config menu (Figure 3-15 on Page 48) is set to Management. Selecting option I from the menu in Figure 3-15 on Page 48 displays the screen shown in Figure 3-19 on Page 52. Note that the IP address is dif-

ferent even though it is the same physical unit. This is because this IP address is defined for a different VLAN. A transceiver can provide automatic IP address assignments to other IP devices in the network by providing DHCP (Dynamic Host Configura-

tion Protocol) services. This service eliminates setting an individual device IP address on Remotes in the network, but it requires some plan-

ning of the IP address range. One drawback to network-wide automatic IP address assignments is that SNMP services might become inacces-

sible as they are dependent on fixed IP addresses. DHCP Server Configuration

(Data and Mgmt) 50 Mercury Reference Manual 05-4446A01, Rev. E You can make a network of radios with the DHCP-provided IP address enabled or with DHCP services disabled. In this way, you can accom-

modate locations for which a fixed IP address is desired. NOTE: There should be only one active DHCP server in a network. If more than one DHCP server exists, network devices might randomly get their IP address from different servers every time they request one. NOTE: Combining DHCP and IEEE 802.1x device authentication might result in a non-working radio if the DHCP server is located at a Remote radio site. If possible, place the DHCP server at the AP location. A DHCP server can be run at a Remote, but it is not recom-

mended if 802.1x Device Authentication is in use and if the AP gets its IP address from the DHCP server on the Remote. In this case, the Remote cannot authenticate to allow the AP to get its address, because the AP needs an address to perform 802.1x device authentication. This results in an unsolvable condition where the AP needs to get an IP address from DHCP at the Remote, but it cant get the address until it is authenti-

cated. Invisible place holder Figure 3-17. DHCP Server Configuration (Mgmt) Menu 05-4446A01, Rev. E Mercury Reference Manual 51 Invisible place holder Figure 3-18. DHCP Server Configuration (Data) Menu DHCP Server StatusEnable/Disable the response to DHCP requests to assign an IP address. [Disabled/Enabled; Disabled]

DHCP NetmaskIP netmask to be assigned along with the IP address in response to a DHCP request. [0.0.0.0]

DHCP starting addressLowest IP address in the range of addresses provided by this device. [0.0.0.0]

DHCP ending addressHighest IP address in the range of addresses provided by this device. A maximum of 256 addresses is allowed in this range. [0.0.0.0]

DHCP DNS addressDomain Name Server address provided by this service. DHCP WINS addressWindows Internet Naming Service server address provided by this service. Invisible place holder Data VLAN Subnet Configuration Menu Figure 3-19. Data VLAN Subnet Configuration Menu 52 Mercury Reference Manual 05-4446A01, Rev. E IP Address ModeDefines the source of this devices IP address. Only static IP addressing mode is available when VLAN Status is enabled [Static; Static]

IP AddressThe IPv4 local IP address. [192.168.1.1]

IP NetmaskThe IPv4 local subnet mask. This value is used when the radio attempts to send a locally initiated message, from either the terminal server or the management process.

[255.255.0.0]

IP GatewayThe IPv4 address of the default gateway device, typically a router. [0.0.0.0]

The lower three lines of the screen (Current IP Address, Current IP Netmask, and Current IP Gateway) show the current addressing configured at the transceiver. Current IP Gateway only displays on this screen if Default Route IF on the Network Interface Config menu (Figure 3-15 on Page 48) is set to Data. Invisible place holder IP Configuration Menu Figure 3-20. IP Configuration Menu CAUTION: Changes to the following parameters while communicating over the network (LAN or over-the-air) might cause a loss of communication with the unit being configured. You must re-establish communication using the new IP address. IP Address ModeDefines the source of this devices IP address.

[Static, Dynamic; Static]

Static IP Address (User Review Recommended)Essential for con-

nectivity to the transceivers MS using the LAN port. Enter any valid IP address that is unique within the network. This eld is unnecessary if DHCP is enabled. [192.168.1.1]

Static IP NetmaskThe IPv4 local subnet mask. This eld is unnecessary if DHCP is enabled. [255.255.0.0]

05-4446A01, Rev. E Mercury Reference Manual 53 Static IP GatewayThe IPv4 address of the network gateway device, typically a router. This eld is unnecessary if DHCP is enabled. [0.0.0.0]

The lower three items on the screen (Current IP Address, Net-

mask and Gateway) show the actual addressing at the trans-

ceiver whether it was obtained from static configuration or from a DHCP server. 802.11 Configuration Submenu Invisible place holder Figure 3-21. 802.11 Configuration Submenu 802.11 ModeConfigures the WiFi radio to be an Access Point for other WiFi devices (Access Point), to connect to a WiFi Access Point at another location (Station), to connect directly to another WiFi device (Ad-Hoc), or to be disabled (disabled). The default setting is disabled. 802.11 SSIDService Set Identifier, the name of the wireless LAN to which to connect. This is equivalent to Network Name in GE MDS terminology. 802.11 Channel(Applies only when 802.11 Mode is set to Access Point) Sets the 802.11 channel the device will use. This can only be set to Auto when in Station mode. 54 Mercury Reference Manual 05-4446A01, Rev. E Invisible place holder Figure 3-22. 802.11 Security Menu 802.11 Privacy ModeDetermines which privacy mode is used.

[None, WEP; None]

802.11 EncryptionDetermines the strength of the WEP encryp-

tion. [64 Bit, 128 Bit; 128 Bit]

WEP PassphraseA user-entered combination of characters that is used to generate a WEP Key. WEP KeyA security code that is generated using the Wireless Equivalency Protocol. It is generated by the entry of a WEP Passphrase (see above) This key should be entered in hexadec-

imal format preceded by 0x. The key should be 13 or 26 hexa-

decimal characters. For example, 1a2b3c4d5e6f709a8b7c6d5e4f. WEP Auth ModeDetermines the authentication mode used by the radio [None, Open, Shared Key, Open and Shared; None]

Invisible place holder Figure 3-23. 802.11 Advanced Configuration Menu 05-4446A01, Rev. E Mercury Reference Manual 55 TX PowerTransmit power of the WiFi radio. [1 to 18; 15]

NIC in BridgeWhen enabled, the WiFi interface is added to the Network Interface Card bridge, allowing traffic to pass between the WiFi and the other interfaces (LAN and wireless).

[enabled, disabled; enabled]

Broadcast 802.11 SSIDWhen enabled, the SSID of the WiFi Access Point is broadcast over the air so that stations will detect the APs presence. [enabled, disabled; enabled]

802.11 Station TimeoutDetermines how quickly inactive sta-

tions are aged out of he WiFi Access Points database.

[1 to 240 mins; 2 mins]

3.4.2 Ethernet Port Configuration Menu The transceiver allows for special control of the Ethernet interface, to allow traffic awareness and availability of the backhaul network for redundancy purposes. NOTE: The transceivers network port supports 10BaseT and 100BaseT connections. Confirm that your hub/switch is capable of auto-switching data rates. To prevent excessive Ethernet traffic from degrading perfor-

mance, place the transceiver in a segment, or behind routers. Invisible place holder Figure 3-24. Ethernet Port Configuration Menu Ethernet Port EnableAllows enabling/disabling Ethernet traffic for security purposes. Setting it to enabled enables the port.

[enabled, disabled; enabled]

Ethernet Port Phy RateThe Ethernet ports configured speed. 56 Mercury Reference Manual 05-4446A01, Rev. E Eth Port Follows Association (Remote Only)When enabled, the Ethernet port is disabled until the Remote associates. This allows a PC or laptop connected to the Remote to know when the wireless link is available. This feature helps middleware on the laptop in making connectivity decisions. In addition, if the Remote moves between Access Points on different subnets, then the laptop can DHCP for a new address when the link comes back up. [enabled, disabled; disabled]

Ethernet Filtering ConfigAllows enabling/disabling filtering and specifying of Ethernet addresses. Ethernet Filtering Configuration Menu Invisible place holder Figure 3-25. Ethernet Filtering Configuration Menu Enable FilteringActivates Ethernet filtering.

[enabled, disabled; disabled]

Address 1, 2, 3, 4Ethernet address fields. When filtering is enabled, the Mercury only accepts traffic on its Ethernet port from the configured addresses.

[Valid MAC address string]

05-4446A01, Rev. E Mercury Reference Manual 57 3.4.3 Bridge Configuration Invisible place holder Figure 3-26. Bridge Configuration Menu Bridge PriorityView/set the priority of the bridge in the span-

ning tree. [0-65535; 32769]

Bridge Hello TimeView/set spanning tree hello time. This parameter affects how often the bridge sends a spanning tree Bridge Protocol Data Unit (BPDU). [1-10 seconds; 2 seconds]

Bridge Forward DelayView/set spanning tree forwarding delay. Affects how long the bridge spends listening and learning after initialization. [4-30 seconds; 5 seconds]. 3.4.4 SNMP Agent Configuration The transceiver contains over 100 custom SNMP-manageable objects as well as the IETF standard RFC1213 for protocol statistics, also known as MIB II. You can use off-the-shelf SNMP managers to access the transceivers SNMP Agents MIB, such as Castle Rock Computing SNMPc and Hewlett Packard OpenView. The transceivers SNMP agent supports SNMPv1, v2, and v3. The objects are split into nine MIB files for use with your SNMP man-

ager. There are textual conventions, common files, and specific files. This allows the flexibility to change areas of the MIB and not affect other existing installations or customers. msdreg.mibMDS sub-tree registrations mds_comm.mibMDS Common MIB definitions for objects and events common to the entire product family mercury_reg.mibMDS sub-tree registrations mercurytrv1.mibSNMPv1 enterprise-specific traps mercurytrv2.mibSNMPv2 enterprise-specific traps 58 Mercury Reference Manual 05-4446A01, Rev. E mercury_comm.mib MIB definitions for objects and events common to the entire Mercury Series mercury_ap.mibMIB definitions for objects and events for an Access Point transceiver mercury_rem.mibDefinitions for objects and events for a Remote radio mercury_sec.mibFor security management of the radio system NOTE: SNMP management requires that the proper IP address, network, and gateway addresses are configured in each associ-

ated network transceiver. In addition, some management systems might require that you compile the MIB files in the order shown above. Invisible place holder Figure 3-27. SNMP Server Configuration Menu This menu provides configuration and control of vital SNMP functions. Read Community StringSNMP community name with SNMPv1/SNMPv2c read access. This string can contain up to 30 alpha-numeric characters. Write Community StringSNMP community name with SNMPv1/SNMPv2c write access. This string can contain up to 30 alpha-numeric characters. Trap Community StringSNMP community name with SNMPv1/SNMPv2c trap access. This string can contain up to 30 alpha-numeric characters. 05-4446A01, Rev. E Mercury Reference Manual 59 V3 Authentication PasswordAuthentication password stored in flash memory. This is used when the Agent is managing pass-

words locally (or initially for all cases on reboot). This is the SNMPv3 password used for Authentication (currently, only MD5 is supported). This string can contain up to 30 alpha-numeric characters. V3 Privacy PasswordPrivacy password stored in ash memory. Used when the SNMP Agent is managing passwords locally (or initially for all cases on reboot). This is the SNMPv3 password used for privacy (DES encryption). This string can contain between 8 and 30 alpha-numeric characters. SNMP ModeThis specifies the mode of operation of the radios SNMP Agent. The choices are: disabled, v1_only, v2_only, v3_only, v1-v2, and v1-v2-v3. If the mode is disabled, the Agent does not respond to any SNMP traffic. If the mode is v1_only, v2_only, or v3_only, the Agent responds only to that version of SNMP traffic. If the mode is v1-v2 or v1-v2-v3, the Agent responds to the specified version of SNMP traffic. [v1-v2-v3]

Trap VersionThis species which version of SNMP is used to encode the outgoing traps. The choices are v1_traps, v2_traps, and v3_traps. When v3_traps is selected, v2-style traps are sent, but with a v3 header. [v1_traps, v2_traps, v3_traps]

Auth Traps StatusIndicates whether or not traps are generated for failed authentication of an SNMP PDU. [Disabled/Enabled;

Disabled]

SNMP V3 PasswordsDetermines whether v3 passwords are managed locally or via an SNMP Manager. The different behav-

iors of the Agent, depending on the mode selected, are described in SNMP Mode above. Trap Manager #1#4 Table of up to four locations on the net-

work to which traps are sent. [Any standard IP address]

NOTE: The number in the upper right-hand corner of the screen is the SNMP Agents SNMPv3 Engine ID. Some SNMP Managers may need to know this ID in order interface with the trans-

ceivers SNMP Agent. The ID only appears on the screen when SNMP Mode is either v1-v2-v3 or v3_only. NOTE: For more SNMP information, see NOTES ON SNMP on Page 180. 3.4.5 AP Location Push Config Menu This menu configures the AP for updating connected remotes with the AP Locations File loaded on the AP. 60 Mercury Reference Manual 05-4446A01, Rev. E Invisible place holder Figure 3-28. AP Location Push Config Menu Invisible place holder Figure 3-29. AP Location Info Configuration Menu, TFTP Mode 05-4446A01, Rev. E Mercury Reference Manual 61 Invisible place holder Figure 3-30. AP Location Info Configuration Menu, USB Mode

(Option Set 1 Remote only) File MediaA selection of methods for transferring files to and from the radio available on firmware version 3.0 radios. The options are: TFTP and USB. TFTP Host AddressIP address of the TFTP server that holds the AP locations file. [any valid IP address; 0.0.0.0]

Transfer OptionsMenu for configuring the TFTP transfer. AP Locations FilenameName of the AP Locations file on the server. [any valid filename string; ap_locations.txt]

Auto AP Location DownloadA setting to force connected remotes to download immediately the AP Locations file on the AP. Remotes that associate to an AP with this feature will also download the file. Retrieve Text FileDownload AP Locations text file from the server. Send Text FileUpload the local AP Locations file to the server. View AP Location FileAllows on-screen review of the AP Loca-

tions file. An example screen is shown in Figure 3-31. 62 Mercury Reference Manual 05-4446A01, Rev. E Invisible place holder Figure 3-31. AP Location Text File AP Locations File Syntax and Guidelines The AP Locations file is used by the Remote radio to determine which Access Point to connect to when operating in Hopping w/ Hand-offs mode. The AP Locations file is a simple text file containing information about the location and configuration of all Access Points that the Remote can associate with. The file is filled in by creating AP definition blocks using tags and labels. The <AP> tag is used to begin a definition block and the </AP> tag ends the block. Within the block, you can declare sev-

eral parameters using a LABEL=VALUE syntax. The possible labels are:

NAMEThe name of the AP. Typically set to the Device Name configured on the AP LATGPS Latitude of the AP in decimal degrees LONGGPS Longitude of the AP in decimal degrees OFFSETPattern Offset configured on the AP BWBandwidth configured on the AP DURFrame duration (10 or 20) configured on the AP MACThe Wireless MAN Address configured on the AP CHANNELSSpecifies which channels are being used by the AP GROUPName of a grouping of Access Points. A Remote con-

figured with Eth Follows Association enabled does not disable its wired port when moving between APs of the same group.This is useful when two or more APs are on the same subnet. MODESingle or Hopping. Specifies the Frequency Mode of the AP. SINGLE_CHANSpecifies the APs Single Frequency mode channel. The MAC label may appear twice if a P23 redundant Access Point is installed at that location. In this case, one MAC statement provides the 05-4446A01, Rev. E Mercury Reference Manual 63 MAC address of the A radio and the other MAC statement provides the MAC address of the B radio. The CHANNELS statement only needs to be present if the channel selection feature is used at the Access Point to limit which channels are active. If all channels are used, you can leave out the CHANNELS statement. You can leave out the BW statement for APs that are configured to 1.75 MHz bandwidth. You can also leave out the DUR statement for APs that are configured with a 20 millisecond frame duration. NOTE: MAC filtering on APs should be used only in a stable network or with the complete understanding that devices not listed in the AP filter will not gain access to the Remotes, nor be acces-

sible to the Remotes. The following shows the syntax of the AP Locations file:

# Mercury Remote AP Locations file

# These lines are comments

# The following line defines the beginning of an AP definition block

<AP>

NAME=MyAccessPoint LAT=43.11790 LONG=-77.61270 OFFSET=3 BW=1.75 DUR=20 MAC=00:06:3D:00:01:23 CHANNELS=1,3,5,7,9,11,13

# The following line defines the end of the AP definition block

</AP>

3.4.6 SNTP Server Configuration The Simple Network Time Protocol (SNTP) allows the Mercury to obtain time of day data from a network server. NOTE: The Mercury can also obtain time of day data from the GPS receiver, if the receiver has a satellite fix. 64 Mercury Reference Manual 05-4446A01, Rev. E Invisible place holder Figure 3-32. SNTP Server Entry (on Network Configuration Menu) When SNTP Server is selected (item H), the area to the right of the param-

eter becomes active, allowing you to enter a valid SNTP server address. Press the Return key to make the address entry active. 3.5 RADIO CONFIGURATION There are two primary layers in the transceiver networkradio and data. Since the data layer is dependent on the radio layer working prop-

erly, configure and set the radio items before proceeding. This section explains the Radio Configuration Menu, (Figure 3-33 for AP, Figure 3-34 for Remote). 3.5.1 Radio Configuration Menu 05-4446A01, Rev. E Mercury Reference Manual 65 Figure 3-33. Radio Configuration Menu

(From Access Point) Invisible place holder Figure 3-34. Radio Configuration Menu Network NameThe user-defined name for the wireless network.

[Any 40 character string; MDS-Mercury]

Transmit Power (AP Only)Sets/displays RF power output level in dBm. This setting should reflect local regulatory limitations and losses in antenna transmission line. (See How Much Out-

put Power Can be Used? on Page 169 for information on how to calculate this value.) [030; 30 (900 model)] [023; 23 (3650 model)]

Max Transmit Power (Remote Only)Sets/displays maximum RF power output level in dBm of the Remote. Power level is still controlled by the AP, but it is limited to the maximum level set here. This setting should reflect local regulatory limitations and losses in antenna transmission line. (See How Much Output Power Can be Used? on Page 169 for information on how to calculate this value.) [030; 30 (900 model) 023; 23 (3650 model) Receive Power (AP Only)View/set the receiver gain setpoint for the expected strength of incoming signals from Remotes. This setting indicates at what level (in dBm) the AP expects to hear the Remote stations. A setting of -70 would set the AP receivers gain to a relatively low level, while a setting of -85 would be a comparatively high gain setting. [-100 to -20; -75]

Frequency ControlOpens a submenu where you can view or set frequency mode bandwidth, channel and other parameters as described in Frequency Control Menu below. Advanced ConfigurationOpens a submenu where you can view or set modulation, protection/hysteresis margins, data compres-

sion, ARQ settings, and other parameters as described in Advanced Conguration Menu on Page 73. Receive Diversity (900 MHz Remote Only)Allows enabling or disabling the RX2 antenna port for receive operation. The use of two antennas allows diversity reception which helps mini-

mize the effects of fading due to multipath reception of signals. 66 Mercury Reference Manual 05-4446A01, Rev. E Frequency Control Menu The items shown on this menu vary depending on the Frequency Mode Selection (Single Channel, Static Hopping, Hopping w/Hand-offs). Examples of all three screens are provided below, followed by a description of the menu items. Invisible place holder Figure 3-35. Frequency Control Menu

(900 MHz AP, Single Channel Freq. Mode) Invisible place holder Figure 3-36. Frequency Control Menu

(900 MHz AP, Static Hopping Freq. Mode) 05-4446A01, Rev. E Mercury Reference Manual 67 Figure 3-37. Frequency Control Menu

(900 MHz Remote, Hopping w/Hand-offs Freq. Mode) Invisible place holder Figure 3-38. Frequency Control Menu

(Mercury 3650 model only) Frequency (Mercury 3650 only)Used to set/display the radios operating frequency. MDS 3650 radios do not employ fre-

quency hopping, thus the entry here is a specific RF operating channel. The allowable entry range is 3652.000 to 3673.000 MHz. Frequency ModeThe unit can operate on one selected fre-

quency or frequency hop. Remotes have the option of using a static hopping configuration or using the AP locations file to select an AP and perform hand-offs. For more information on hand-offs, see Table 3-2 on Page 71. Changing this parameter requires a radio reboot.

[Static Hopping, Hopping with Hand-offs, Single Channel;

Single Channel]

68 Mercury Reference Manual 05-4446A01, Rev. E NOTE:

Frequency Mode Static Hopping on Access Points requires TDD Sync Mode GPS Required. Channel/Frequency Allocations for Single Channel 900 MHz are shown in Table 3-1. The transceiver uses up to 14 channels

(0-13) depending on the bandwidth used (1.75 MHz or 3.5 MHz). Table 3-1. Channel/Frequency Allocations Channel 0 1.75 MHz B/W 3.5 MHz B/W 904.000000 903.000000 1 2 3 4 5 6 7 8 9 10 11 12 13 904.800000 907.600000 906.600000 911.400000 908.600000 915.000000 910.400000 918.600000 912.200000 922.400000 914.000000 926.000000 916.000000 917.800000 919.600000 921.400000 923.400000 925.200000 927.000000 RF BandwidthView/set the radios RF operating bandwidth. Radios are factory-configured for either 1.75 MHz or 3.5 MHz maximum bandwidth. Determine the factory configu-

ration of a radio by viewing the CONFIG number on the label at the bottom of the radio. 1.75 MHz units will have a Configuration string starting with HGA/R9N1, and 3.5 MHz units will have a string starting with HGA/R9N3. The bandwidth setting on this menu does not necessarily have to match the configured bandwidth of the radio, but it is limited by it. That is, you can set a 3.5 MHz radio to either 1.75 or 3.5, but you can only set a 1.75 MHz radio to 1.75. Note that setting a 3.5 MHz bandwidth radio to operate at 1.75 MHz bandwidth will cause a slight degradation of inter-

ference rejection capability. Note that this parameter is read-only when Frequency Mode is set to Hopping w/Hand-offs.

[1.75MHz, 3.5MHz]

The Mercury 3650 can operate at 1.75 MHz, 3.5 MHz, 5 MHz, or 7 MHz bandwidth. The unit uses a digital filter so that any unit can operate at any bandwidth. 05-4446A01, Rev. E Mercury Reference Manual 69 Single Frequency ChannelThe RF frequency that the inte-

grated radio will operate on when in single frequency

(non-hopping) mode. [0 to 6 for 3.5-MHz, 0 to 13 for 1.75-MHz; 0]. Frame DurationDefines the over-the-air media access con-

trol framing. Note that this parameter is read-only when Fre-

quency Mode is set to Hopping w/Hand-offs. [5, 8, 10, or 20 msec;

20 msec]

Hop PatternSelects a pre-defined series of channels that is followed when hopping. Note that this parameter is read-only when Frequency Mode is set to Hopping w/Hand-offs. Hop Pattern OffsetInserts an offset into the hop pattern that is synchronized with the GPS. For example, if the offset is 0, the start of the pattern is aligned with the GPS timing. If the offset is 3, then the fourth hop of the pattern is aligned with the GPS timing. All of the APs that are part of a network should use the same pattern and each one should have its own offset. In the diagram below, one Remote is configured for static hopping and will only associate with AP1 because they are both using Offset 0. The hand-off configured Remote, using its AP Locations file, may connect to AP1, AP2, or AP3. The Remote does this by determining the Offset for each AP, then configuring its radio. AP 1 Pattern A Offset 0 AP 2 Pattern A Offset 1 AP 3 Pattern A Offset 2 RM Static Hopping Offset 0 RM Hopping w/

Hand-offs Current AP (Remote only)Shows the name of the AP that the Remote is trying to associate with. Note that this param-

eter is read-only when Frequency Mode is set to Hopping w/Hand-offs. TDD Sync Mode (AP only)Indicates if the Access Points trans-

missions should synchronize with the GPS timing. Configure this parameter to GPS Required when the AP is configured for Static Hopping. TDD Sync Mode (Time-Division Duplex) is use-

ful in eliminating same-network interference for multiple-AP installations. When enabled, all AP transmissions are synchro-

nized using GPS timing information. The result is that no AP 70 Mercury Reference Manual 05-4446A01, Rev. E transmits while another is receiving, which prevents AP-to-AP interference. Changing this parameter requires a radio reboot.

[Free Run, GPS Required; Free Run] Note: Do not use the Prefer GPS setting. Channel Selection (AP only)Opens a submenu where you can specify channel usage. External GPS PPS SignalIndicates whether or not an external Pulse Per Second (PPS) signal is available. The setting may be changed by pressing the spacebar after selection of the menu item. This allows the radio to use the proper timing scheme when frequency hopping. Advanced Control (Remote only)Brings up a submenu (see Figure 3-39) where additional communication parameters may be set. Hardware Filter (900 MHz only)This field provides a read-only indication of the maximum bandwidth of the radio. [1.75 MHz or 3.5 MHz]

Hand-Off Mode Parameters In a mobile or portable application, a Remote radio can move and asso-

ciate with different APs depending on its location. The process by which the Remote ends the connection with one AP and begins a connection with another AP is called hand-off. Table 3-2 lists the hand-off parameters for Remote transceivers and explains how they operate under different signal conditions. Table 3-2. Remote Hand-Off Parameters Strict Distance Strict Connection Strict Signal Signal and Distance Description The Remote always chooses the closest AP regardless of connection status, RSSI, etc. The Remote will only choose a new AP when the modem link is lost. The Remote chooses a new AP when the modem link is lost or when the RSSI or SNR falls below the threshold. The Remote then chooses the closest AP. Operates the same way as the Strict SIgnal method except that the current AP is abandoned only if the next AP is within the distance threshold. Signal, Dis-

tance, and Bearing Operates the same way as the Signal and Distance method except that the current AP is abandoned only if the bearing is away from the current AP. AP(s) Used

(see note be-

low Table 3-2) Only closest AP. Closest 3 APs. Closest 3 APs. Closest 3 APs;

AP must be within Distance Threshold. Closest 3 APs;

AP must be within Distance Threshold. Max. Scanning Seconds N/A Applicable Applicable Applicable Applicable 05-4446A01, Rev. E Mercury Reference Manual 71 Table 3-2. Remote Hand-Off Parameters Strict Distance Strict Connection Strict Signal Signal and Distance N/A N/A N/A Applicable Applicable Applicable N/A Applicable Applicable Signal, Dis-

tance, and Bearing Applicable Applicable Applicable N/A RSSI Threshold SNR Threshold N/A Distance N/A Threshold Blacklist Time N/A Applicable Applicable Applicable Applicable NOTE: In Table 3-2 above, modes using the Closest 3 APs first attempt to connect to the closest AP. If after the maximum number of scanning seconds (Max. Scanning Seconds) a link is not established, then the next closest AP is chosen. If after another maximum number of scanning seconds a link is not established, then the third closest AP is chosen. If a link still is not established, the Remote again chooses the closest AP and continues this cycle until it is associated to one of the APs. NOTE: In Table 3-2 above, modes which use the RSSI and SNR Thresh-

olds use them in an or logic fashion. That is, if the RSSI is below the set threshold OR the SNR is below threshold, the Remote drops the current AP. Advanced Control Menu Invisible place holder Figure 3-39. Advanced Control Menu

(Hopping with Handoff Mode, Remote Only) AP Selection ModeThe method used by the Remote to determine what AP to connect to. It may be based on Signal, Distance and Bearing (from the AP's GPS coordinates in the AP locations file), or Connection. Table 3-2 on Page 71 summarizes these parameters and other selections on this menu. 72 Mercury Reference Manual 05-4446A01, Rev. E Max Scanning TimeThe maximum time to try to connect to an AP before trying the next one in the AP Locations file. RSSI ThresholdThe RSSI cutoff for Signal modes. When the RSSI drops below this value, the Remote disconnects and looks for a new AP. SNR ThresholdThe SNR cutoff point for Signal modes. When the SNR drops below this value, the Remote disconnects and looks for a new AP. Distance ThresholdThe distance cutoff when operating in Distance mode. When the Remote's AP gets farther away than this distance, it dis-

connects and look for a new AP. Blacklist TimeThe amount of time (in seconds) that an AP is ignored when the Remote is trying to find a better connection. Advanced Configuration Menu Invisible place holder Figure 3-40. Advanced Configuration Menu Adaptive ModulationEnables automatic selection of modulation and FEC rate based on SNR. [enabled, disabled; enabled]

Protection MarginA number of decibels of SNR added to the minimum SNR required for a given modulation and FEC rate. See Modulation Protection and Hysteresis Margins on Page 75 for more information. [0-50; 3]

Hysteresis MarginA number of decibels of SNR added to the maximum SNR required before shifting to the next higher mod-

ulation and FEC rate. See Modulation Protection and Hyster-

esis Margins on Page 75 for more information. [0-50; 3]

Data CompressionThis setting determines whether over-the-air data packets will be compressed. [enabled, disabled; enabled]

05-4446A01, Rev. E Mercury Reference Manual 73 Max ModulationSets the highest modulation speed the trans-

ceiver will use.

[BPSK, QPSK-1/2, QPSK-3/4, 16QAM-1/2, 16QAM-3/4, 64QAM-2/3;

QAM16-3/4]

Cyclic Prefix (AP only)Amount of additional information added to the over-the-air packets to mitigate the effects of chan-

nel multipath. [1/4, 1/8, 1/16,1/32; 1/16]

Channel Type (AP only)This parameter, available on Access Point units, must be set appropriately according to the signal conditions of a network. For installations with strong signals, low interference, and minimal fading, set the Channel Type parameter to Static. This setting is generally appropriate for Access Points whose Remotes are in fixed locations. It supports a large offered payload with high packet rates. For installations with significant interference and fading or nomadic/mobile Remotes, set the Channel Type parameter to Dynamic. [Static, Dynamic; Static]

ARQ (AP only)Enables the Automatic Repeat Request func-

tion.

[enable, disable; enabled]

ARQ Window Size (AP only)The maximum number of blocks to send before receiving an acknowledgement. [11024; 512]

ARQ Block Size (AP only)ARQ is applied to payload data in blocks of this size. [42040; 256]

ARQ Block Lifetime (AP only)ARQ blocks are valid for this length of time. [0655; 655]

ARQ Transmitter Delay (AP only)The length of time the trans-

mitter waits before repeating an unacknowledged packet.

[1655; 35]

ARQ Receiver Delay (AP only)The length of time the receiver waits before repeating an unacknowledged packet. [1655; 35]

Downlink Percentage (AP only)The percentage of link time given to downstream traffic. It should be set to 50% when Adap-

tive Split is set to enabled. [10-90%; 50%]

Adaptive Split (AP only)The adaptive split feature provides improved link utilitization and throughput for burst payload traffic. The Mercury is a TDD system and normally allocates 50% of its capacity to the downlink and 50% to the uplink. When adaptive split is enabled, the Media Access Controller

(MAC) in the Access Point monitors the traffic flow continu-

ously in the downlink and uplink directions. The MAC automat-

ically modifies the downlink split in response to the traffic load. When more traffic is flowing upstream, the downlink split changes to allocate additional capacity to the uplink. When more traffic is flowing downstream, the downlink gets addi-

tional capacity. If TDD synchronization is used to synchronize Access Points and minimize inter-Access Point interference, Adaptive Split should be disabled. [enabled, disabled; enabled]

74 Mercury Reference Manual 05-4446A01, Rev. E Modulation Protection and Hysteresis Margins Table 3-3 on Page 75 shows the relationship between the radios Protec-

tion Margin, Hysteresis Margin, and the SNR range allowed for each form of modulation. Column A lists the available modulation types for the radio, while col-

umns B and C show the minimum SNR range required to operate in each modulation. For example, an SNR of 5.8 dB in Column B is required for QPSK modulation with an FEC rate of 1/2. An SNR of 8.4 dB is required for QPSK modulation with an FEC rate of 3/4. Columns B and C have a Hysteresis Margin of 0 dB. This means there is no overlap between the maximum SNR for BPSK (5.8 dB) and the minimum SNR for QPSK-1/2 (5.8 dB). Columns D and E show the SNR ranges with a Protection Margin and Hysteresis Margin of 3 dB. The Protection Margin is added to each value in Columns B and C to get the corresponding value in Columns D and E. The Hysteresis Margin is then added to the Max SNR value. For example, the third SNR value in Column D is 11.4 dB (8.4 + 3 =

11.4 dB), and the third SNR value in Column E is 17.1 (11.1 + 3 + 3 =

17.1 dB). Note that with a Hysteresis Margin of 3 dB, there is an overlap of 3 between the Max SNR of one modulation and the Min SNR of the next higher modulation. In this case, if a link is operating with an SNR of 15 dB, then QPSK-3/4 modulation is used. The SNR must go above 17.1 dB before the link shifts up to 16QAM-1/2 modulation. Conversely, the SNR will need to drop below 11.4 dB before the link shifts down to QPSK-1/2. The blank entries (--) in the table indicate infinite SNR (i.e., the top of the range). For example, in columns B and C, 64QAM-3/4 modulation is used for all SNR values from 20 dB and up. Table 3-3. Adaptive Modulation Protection and Hysteresis Margins A B C D E F Protection Hysteresis Min SNR 3.3 5.8 8.4 11.1 14.4 18.4 20 BPSK QPSK-1/2 QPSK-3/4 16QAM-1/2 16QAM-3/4 64QAM-2/3 64QAM-3/4 Protection Hysteresis 0 0 Max SNR Min SNR 5.8 3.3 Protection Hysteresis 3 3 Max SNR Min SNR 11.8 3.3 8.4 11.1 14.4 18.4 20

8.8 11.4 14.1 17.4 21.4 23 14.4 17.1 20.4 24.4 26

10.8 13.4 16.1 19.4 23.4 25 G 5 3 Max SNR 13.8 16.4 19.1 22.4 26.4 28

05-4446A01, Rev. E Mercury Reference Manual 75 COM1 PortDual Purpose Capability TCP vs. UDP Serial Encapsulation 3.5.2 Serial Port Configuration Overview The transceiver includes an embedded serial device server that provides transparent encapsulation over IP. In this capacity, it acts as a gateway between serial and IP devices. Two common scenarios are PC applica-

tions using IP to talk to remote devices, and serial PC applications talking to remote serial devices over an IP network. These data services are available from the COM1 port of the radio. The COM1 port is used as a local console connection point and to pass serial data with an external device. Setting the COM1 port status to Enable prevents access to the Management System (MS) through this port. However, the MS can still be accessed via the LAN port using Telnet or a web browser. NOTE: To restore the COM1 port to support Management System services, connect a terminal to the port, select the proper baud rate (115,200 is default), and enter an escape sequence (+++) to reset it to the console mode. There is a configuration parameter for the console baud rate and another parameter for the serial data baud rate. These items can be different, so when switching out of data mode to console mode, the port might also change its baud rate. TCP and UDP services are used by the transceivers embedded serial device server. TCP provides a connection-oriented link with end-to-end acknowledgment of data, but with some added overhead. UDP provides a connectionless best-effort delivery service with no acknowledgment. Most polled protocols are best served by UDP service as the protocol itself has built-in error recovery mechanisms. UDP provides the needed multidrop operation by means of multicast addressing. On the other hand, TCP services are best suited for applications without a recovery mechanism (error-correction) and must have the guaranteed delivery that TCP provides in spite of the extra overhead. The IP-to-Serial Application Example on Page 83 shows how to do this. Transparent encapsulation, or IP tunneling, provides a mechanism to encapsulate serial data in an IP envelope. All bytes received through the serial port are put into the data portion of a TCP or UDP packet (TCP or UDP are user-configurable options). In the same manner, all data bytes received in a TCP or UDP packet are output through the serial port. When the radio receives data through the serial port, it is buffered until the packet is received completely. There are two events that signal an end-of-packet to the radio: a period of time since the last byte was 76 Mercury Reference Manual 05-4446A01, Rev. E received, or a number of bytes that exceed the buffer size. Both of these triggers are user-configurable. One radio can perform serial data encapsulation (IP-to-Serial) and talk to a PC. You can use two radios together (or one radio and a terminal server) to provide a serial-to-serial channel. For more information, see IP-to-Serial Application Example on Page 83 and Point-to-Point Serial-to-Serial Application Example on Page 83. TCP Client vs. TCP Server On a TCP session there is a server side and a client side. You can con-

figure the transceiver to act as either a server or a client. The server always waits for requests from clients. UDP Multicast Data Buffering The client mode attempts to establish a connection to a server (typically running on a PC) whenever it receives data on the serial port. There is also a Client/Server mode, where the client establishes a connection when data is received on the serial port and the server is not currently handling a connection. IP provides a mechanism to perform a limited broadcast to a specific group of devices. This is known as multicast addressing. Multicast addressing requires the use of a specific branch of IP addresses set apart by the Internet Assigned Numbers Authority (IANA) for this purpose. UDP multicast is generally used to transport polling protocols typically used in SCADA applications where multiple remote devices will receive and process the same poll message. As part of the Multicast implementation, the radio sends IGMP mem-

bership reports and IGMP queries, and responds to membership queries. It defaults to V2 membership reports, but responds to both V1 and V2 queries. The Point-to-Multipoint Serial-to-Serial Application Example on Page 84 shows how to provide multicast services. Data buffering is always active regardless of the selected mode. If you connect EIA-232 serial devices to the transceiver, review these parame-

ters carefully. Serial Configuration Wizard GE MDS recommends the Serial Configuration Wizard, available through the Serial Port Configuration Menu, for configuration of the serial terminal services. The wizard uses a step-by-step process, eliminates possible conflicting settings, and streamlines complex configurations. You can bypass the wizard by selecting option B) View Current Settings and adjusting the individual settings of the appropriate parameter. 05-4446A01, Rev. E Mercury Reference Manual 77 Serial Port Configuration Menu Invisible place holder Figure 3-41. Serial Port Configuration Menu Figure 3-42. Serial Configuration Wizard Begin WizardTool for configuring serial ports using a step-by-step process. View Current SettingsDisplays all setable options. Varies depending on the selected IP protocol. 78 Mercury Reference Manual 05-4446A01, Rev. E Configuring for UDP Point-to-Multipoint Invisible place holder Figure 3-43. UDP Point-to-Multipoint Menu Use UDP point-to-multipoint to send a copy of the same packet to mul-

tiple destinations, such as in a polling protocol. StatusEnable/Disable the serial data port. ModeThe type of IP port offered by the transceivers serial device server. [TCP, UDP; TCP]

RX IP PortReceive IP data from this source and pass it through to the connected serial device. The port number must be used by the application connecting to local TCP or UDP socket. [Any valid IP port; 30010]

TX IP Address (used instead of Local IP Address when using UDP Point-to-Multipoint) Configure with a valid Multi-

cast address (224.0.0.0239.255.255.255). IP packets received with a matching destination address are processed by this unit. [Any legal IP address; 0.0.0.0]

TX IP Port (used instead of Local IP Port when using UDP Point-to-Multipoint)This port number must match the number used by the application connecting to local TCP or UDP socket. [1-64,000; 30010]

Baud RateData rate (payload) for the COM port, in bits-per-second. [1,200115,200; 19200]

Byte FormatFormatting of data bytes, representing data bits, parity and stop bits. [7N1, 7E1, 7O1, 8N1, 8E1, 8O1, 8N1, 7N2, 7E2, 7O2, 8N2, 8E2, 8O2; 8N1]

Buffer SizeMaximum amount of characters that the Remote end buffers locally before transmitting data through the serial port. [1255; 255]

Inter-Packet DelayAmount of time that signal the end of a message, measured in tenths of a second. [default = 1 (that is, 1/10th of a second)]

05-4446A01, Rev. E Mercury Reference Manual 79 Commit Changes and Exit WizardSave and execute changes made on this screen (shown only after changes have been entered). Invisible place holder Configuring for UDP Point-to-Point Use UDP point-to-point configuration to send information to a single device. Figure 3-44. UDP Point-to-Point Menu StatusEnable/Disable the serial data port. ModeUDP Point-to-Point. This is the type of IP port offered by the transceivers serial device server.

[TCP, UDP; TCP]

RX IP PortPort number where data is received and passed through to the serial port. The application connecting to this transceiver must use this port number.

[164,000; 30010]

TX IP AddressData received through the serial port is sent to this IP address. To reach multiple Remotes in the network, use UDP Point-to-Multipoint.

[Any legal IP address; 0.0.0.0]

TX IP PortThe destination IP port for data packets received through the serial port on the transceiver.

[164,000; 30010]

Talkback EnableTalkback is a mode where the radio returns a serial message received within a time-out period back to the last address of an incoming UDP message. If the time-out expires, the unit sends the serial data to the configured address. [Enable, Disable; Disabled]

Baud RateData rate (payload) for the COM port, in bits-per-second. [1,200115,200; 19200]

Byte FormatFormatting of data bytes. Data bits, parity and stop bits. [7N1, 7E1, 7O1, 8N1, 8E1, 8O1, 8N1, 7N2, 7E2, 7O2, 8N2, 8E2, 8O2; 8N1]

80 Mercury Reference Manual 05-4446A01, Rev. E Buffer SizeMaximum amount of characters that the Remote end buffers locally before transmitting data through the serial port. [1255; 255]

Inter-Packet DelayAmount of time that signal the end of a message, measured in tenths of a second. [default = 1 (that is, 1/10th of a second)]

Commit Changes and Exit WizardSave and execute changes made on this screen (shown only after changes have been entered). Invisible place holder Configuring for TCP Mode Figure 3-45. TCP Client Menu (Remote) StatusEnable/Disable the serial data port. ModeTCP Client. This is the type of IP port offered by the transceivers serial device server. [TCP, UDP; TCP]

TX IP AddressThe IP address to be used as a destination for data received through the serial port.

[Any legal IP address; 0.0.0.0]

TX IP PortThe destination IP port for data packets received through the serial port on the transceiver.

[Any valid IP port; 30010]

TCP KeepaliveAmount of time (in seconds) that the trans-

ceiver waits for data before terminating the TCP session.

[0600; 600]

Baud RateData rate (payload) for the COM port, in bits-per-second. [1,200115,200; 19200]

Byte FormatInterface signaling parameters. Data bits, parity and stop bits.

[7N1, 7E1, 7O1, 8N1, 8E1, 8O1, 8N1, 7N2, 7E2, 7O2, 8N2, 8E2, 8O2;

8N1]

Buffer SizeMaximum amount of characters that the Remote end buffers locally before transmitting data through the serial port. [1255; 255]

05-4446A01, Rev. E Mercury Reference Manual 81 Inter-Frame Packet DelayA measurement representing the end of a message, measured in tenths of a second.

[default = 1 (that is, 1/10th of a second)]

Commit Changes and Exit WizardSave and execute changes made on this screen (shown only after changes have been entered). Invisible place holder Figure 3-46. TCP Server Menu (AP) StatusEnable/Disable the serial data port. ModeTCP Server. This is the type of IP port offered by the transceivers serial device server.

[TCP, UDP; TCP]

RX IP PortReceive IP data from this source and pass it through to the connected serial device. The application con-

necting to the local TCP or UDP socket must use this port number.

[Any valid IP port; 30010]

Baud RateData rate (payload) for the COM port, in bits-per-second. [1,200115,200; 19200]

Byte FormatInterface signaling parameters. Data bits, parity and stop bits.

[7N1, 7E1, 7O1, 8N1, 8E1, 8O1, 8N1, 7N2, 7E2, 7O2, 8N2, 8E2, 8O2;

8N1]

Buffer SizeMaximum amount of characters that the Remote end buffers locally before transmitting data through the serial port. [1255; 255]

Inter-Packet DelayAmount of time that signal the end of a message, measured in tenths of a second. [default = 1 (that is, 1/10th of a second)]

Commit Changes and Exit WizardSave and execute changes made on this screen (shown only after changes have been entered). 82 Mercury Reference Manual 05-4446A01, Rev. E IP-to-Serial Application Example You must choose UDP or TCP to establish communications. This depends on the type of device you are communicating with at the other end of the IP network. In this example, we will use TCP to illustrate its use. In TCP mode, the transceiver remains in a passive mode, offering a socket for connection. Once a request is received, data received at the serial port is sent through the IP socket and vice versa, until the connec-

tion is closed or the link is interrupted. In this mode, the transceiver behaves the same, whether it is an Access Point or a Remote.

(See Figure 3-47 and Table 3-4) NOTE: The TCP session has a timeout of 10 minutes (600 seconds). If inactive for that time, the session is closed. The transceiver offers the port again for connection after this time expires. From the PC, establish a TCP connection to the IP address of the Remote transceiver and to the IP port as configured above (30010). Use a Telnet client application to establish this connection. Data can now be sent between the PC and the RTU or other connected device. 192.168.0.10 192.168.0.1 Invisible place holder 192.168.0.2 Establishing a Connection Ethernet Crosssover LA N Computer or Network Access Point C O M 1 C O M 2 P R W LIN K Remote EIA-232 RTU Figure 3-47. IP-to-Serial Application Diagram Table 3-4. Serial Port Application Configuration Transceiver Location Access Point IP-to-Serial Connection Menu Item Setting None is required None is required Remote Unit IP Address 192.168.0.2 Status IP Protocol Baud Rate Flow Control Local IP Port Enabled TCP 9,600 (Example) None 30010 Point-to-Point Serial-to-Serial Application Example Once you have configured the transceivers, they begin processing data presented at the COM ports. Data presented at the Access Points COM port is packetized and sent via UDP to the Remote. Upon receiving the 05-4446A01, Rev. E Mercury Reference Manual 83 packet, the Remote strips the data out of the UDP packet and sends it out its COM port. Likewise, data presented at the Remotes COM port is packetized, sent to the Access Point, stripped, and sent out the Access Points COM port. This configuration does not use multicast addressing. Invisible place holder 192.168.0.10 192.168.0.1 192.168.0.2 EIA-232 Terminal or Computer Access Point Remote RTU LA N COM1 COM2 PW R LIN K EIA-232 Figure 3-48. Point-to-Point Serial-to-Serial Application Diagram Table 3-5. Serial Port Application Configuration Transceiver Location Access Point (COM1) Menu Item Status Setting Enabled Data Baud Rate 9,600 (Example) SIFD IP Protocol Remote IP Address Remote IP Port Local IP Port Remote Unit (COM1) Status 4 UDP 192.168.0.2

(IP address of the Remote radio) 30010 30010 Enabled Data Baud Rate 9,600 (Example) Flow Control X-ON/X-OFF (Example) SIFD IP Protocol Remote IP Address 4 (Characters) UDP 192.168.0.1

(IP address of the AP) Remote IP Port Local IP Port 30010 30010 Point-to-Multipoint Serial-to-Serial Application Example The operation and data flow for this mode is very similar to Point-to-Point serial-to-serial application, except that it uses multicast addressing. The primary difference is that data presented at the Access Points COM port is packetized and sent using UDP to all of the Remotes. Upon receiving the packet, all of the Remotes strip the data from the UDP packet and send it out their COM ports. Likewise, data presented at any of the Remotes COM ports is packetized, sent to the Access Point, stripped, and sent out the Access Points COM port (see Figure 3-49, Table 3-6, Figure 3-50, and Figure 3-51 on Page 86). 84 Mercury Reference Manual 05-4446A01, Rev. E Invisible place holder 192.168.0.10 192.168.0.1 192.168.0.2 LA N C O M 1 C O M 2 EIA-232 Access Point Terminal or Computer 192.168.0.3 LA N LA N 192.168.0.4 C O M 1 C O M 2 C O M 1 C O M 2 P R W LIN K P R W LIN K P R W LIN K EIA-232 Remote RTU EIA-232 RTU Remote EIA-232 Remote RTU Figure 3-49. Point-to-Multipoint Serial-to-Serial Application Diagram Table 3-6. Serial Port Application Configuration Invisible place holder Transceiver Location Access Point (COM1) Menu Item Status Baud Rate Flow Control IP Protocol Remote IP Address Remote IP Port Local IP Port Remote Units (COM1) Enable Baud Rate Flow Control IP Protocol Setting Enabled 9600 (Example) Disabled UDP 224.254.1.1 Multicast Address1 30010 30010 Enabled 2,400 (Example) Hardware (Example) UDP Remote IP Address 192.168.0.1 Remote IP Port Local IP Port Local Multicast Address 30010 30010 224.254.1.1 Multicast Address2 1. This address is an example only. Any Class D IP address

(224.0.0.0239.255.255.255) will work. 05-4446A01, Rev. E Mercury Reference Manual 85 Figure 3-50. Serial Port ConfigurationAccess Point Figure 3-51. Radio Serial Port ConfigurationRemote Mixed Modes In this example, the TCP mode does not involve the Access Point. Thus, the transceiver in a single network can run in both modes at the same time. In other words, you can configure some Remotes for TCP mode and others (along with the Access Point) for UDP mode. In this configuration, the Host PC can use both data paths to reach the RTUs. This is helpful when a mixed collection of RTUs is present where some RTUs can operate in a broadcast form while others cannot (see Figure 3-52 on Page 87 and Table 3-7 on Page 87). 86 Mercury Reference Manual 05-4446A01, Rev. E Operation and Data Flow Communicate with RTU A by Telneting to Remote 1, port 30010. Communicate with RTU B by Telneting to Remote 2, port 30010. Communicate with RTUs C and D by sending and receiving data from the Access Points COM port. All communication paths can be used simultaneously. Invisible place holder Access Point Transceiver Ethernet Crosssover Terminal or Computer EIA-232 LA N LA N LA N LA N C O M 1 C O M 2 C O M 1 C O M 2 C O M 2 C O M 1 C O M 1 C O M 2 RTUA EIA-232 Remote 1 RTUB EIA-232 Remote 2 RTUC EIA-232 Remote 3 RTUD EIA-232 Remote 4 P R W LIN K P R W LIN K P R W LIN K P R W LIN K Figure 3-52. Mixed-Modes Application Diagram Table 3-7. Serial Port Application Configuration Transceiver Location Access Point Menu Item Status Baud Rate Flow Control IP Protocol Setting Enabled 9,600 Disabled UDP Send to Address A multicast IP address such as 224.254.1.1 Send to Port Receive on Port 30010 30010 Receive on Address 0.0.0.0 (Not Used) Remote Units 1 & 2 (COM1) Status Baud Rate Flow Control IP Protocol Receive on Port Remote Units 3 & 4 (COM1) Status Baud Rate Flow Control IP Protocol Enabled 2,400 Disabled TCP 30010 Enabled 9,600 Disabled UDP 05-4446A01, Rev. E Mercury Reference Manual 87 Table 3-7. Serial Port Application Configuration (Continued) Transceiver Location Menu Item Send to Address Send to Port Receive on Port Receive on Address Setting IP address of the AP 30010 30010 224.254.1.1

(The multicast IP address used for the APs Send To Address above) 3.6 MODBUS / TCP SERVER CONFIGURATION Modbus is a serial communications protocol developed by Schneider Electric (Modicon) for communication between programmable logic controllers (PLCs), remote terminal units (RTUs) and other industrial electronic devices. It has become an established standard in the industry, and is now used by many manufacturers of industrial data equipment. Mercury Series transceivers running version 2.2.0 firmware or later include Modbus functionality. This section of the addendum contains an overview of the Modbus/TCP Server and provides menu details for using this feature. You should also review Conguring for TCP Mode section on Page 81. NOTE: This material assumes you have an understanding of Ethernet networking, TCP/IP, and Modbus serial protocols. Refer to the following web site for additional information:

www.modicon.com/TECHPUBS/intr7.html. NOTE: Modbus/TCP functionality is provided on the COM1 port of the transceiver only. 3.6.1 Modbus/TCP in Mercury TransceiversAn Overview The transceiver implements a Modbus/TCP server that bridges Modbus/TCP to either: Modbus RTU or Modbus/ASCII. It does not function as a Modbus/TCP client. The transceiver converts Modbus/TCP requests to either RTU or ASCII serial Modbus packets and sends them to the configured serial port. It waits up to the timeout period for a reply on the serial port, and if one arrives, it converts the response back to Modbus/TCP and sends it to the connected Modbus/TCP client. 88 Mercury Reference Manual 05-4446A01, Rev. E 3.6.2 Menu Selections Connect a PC to the transceiver as described in STEP 3: CONNECT PC TO THE TRANSCEIVER section on Page 25, and access the embedded management system. Follow the steps below to proceed with Modbus/TCP configuration. 1. From the Serial Configuration Wizard opening screen (Figure 3-53 on Page 89), select A to begin the wizard. Invisible place holder Figure 3-53. Configuration Wizard Opening Screen 2. Choose the IP protocol you wish to use (TCP, UDP, or Mod-

bus/TCP) by selecting the appropriate letter from the menu. Figure 3-54. IP Protocol Selection Screen 3. On the next screen (Figure 3-55 on Page 90), choose the listening port you wish to use for the Modbus/TCP server. The default is port 502. Press N to continue. 05-4446A01, Rev. E Mercury Reference Manual 89 Figure 3-55. Modbus/TCP Server Listening Port 4. On the next screen (Figure 3-56), press A to change the Modbus serial format, then press the space bar to toggle between the avail-

able formats (MODBUS/RTU or MODBUS/ASCII). Press B to enter the Modbus serial timeout value in milliseconds. Press N to continue the wizard. NOTE: The only and Modbus/ASCII is the form of the framing sequence, error check pattern, and address interpretation. between Modbus/RTU difference Figure 3-56. Choose Modbus Serial Format and Timeout Value Note: Modbus Timeout setting is in milliseconds, not seconds as displayed in the example above. 90 Mercury Reference Manual 05-4446A01, Rev. E 5. When the next screen appears (Figure 3-57), press A to select the desired data baud rate and B to select the data byte format. Press N to continue. Figure 3-57. Select Data Baud Rate and Byte Format 6. The screen shown in Figure 3-58 appears next. Press A to select the Buffer Size of message packets, and B to select the Inter-Frame Delay. Press N to continue with the wizard. Invisible place holder Figure 3-58. Buffer Size and Inter-Frame Delay Values 7. On the next screen (Figure 3-59 on Page 92), select A and use the spacebar to enable the serial port for data communication. Press N to continue the wizard. 05-4446A01, Rev. E Mercury Reference Manual 91 Invisible place holder Figure 3-59. Serial Port Status Screen 8. Review all settings on the summary screen shown in Figure 3-60. If all settings are correct, press X to conrm and exit the wizard. If not, select the letter of the item(s) you wish to change. Invisible place holder Figure 3-60. Serial ConfigurationSummary Screen This completes the menu selections for Modbus/TCP operation. 3.7 SECURITY CONFIGURATION MENU The transceivers security features are grouped into four major catego-

ries and are accessible from the Security Configuration Menu (see Figure 3-61). These categories are:

Device SecurityContains settings for controlling access to the radio itself for configuration and management. 92 Mercury Reference Manual 05-4446A01, Rev. E Wireless SecurityControls how and when radios communicate with each other, as well as how data traffic is handled. RADIUS ConfigurationDeals with IEEE 802.1x device authentication and authorization using a central server. Manage Certificates (Remote only)Allows setting of certificate types, download paths, and TFTP parameters. Invisible place holder Figure 3-61. Security Configuration Menu Selecting any of the Security Configuration Menu items opens a sub-

menu where you can view or change settings. Examples of these screens and more detailed descriptions of their contents are provided below. 3.7.1 Device Security Menu The Device Security Menu (Figure 3-62) controls how the radios can be accessed either locally or remotely for configuration and management. 05-4446A01, Rev. E Mercury Reference Manual 93 Invisible place holder Figure 3-62. Device Security Menu Telnet AccessControls Telnet access to the transceivers man-

agement system. [enabled, disabled; enabled]

SSH AccessControls access to the Secure Shell (SSH) server.

[enabled, disabled; enabled]

HTTP ModeControls access to the transceivers management system via the web server. [disabled, HTTP, HTTPS; HTTP]

HTTP Auth ModeSelects the mode used for authenticating a web user. [Basic Auth, MD5 Digest; Basic Auth]

User Auth MethodView/set the method of authentication for users. [Local, Radius; Local]

User Auth FallbackView/set method of authentication to use if the RADIUS server is unavailable. [None, Local; None]

User PasswordsAllows changing of Administrative and Guest passwords. When selected, a new screen appears (Figure 3-63 on Page 95). 94 Mercury Reference Manual 05-4446A01, Rev. E User Passwords Menu Invisible place holder Figure 3-63. User Passwords Menu To change the Administrator or Guest password, select the appropriate menu item (A or B). A flashing cursor appears to the right. From here, type the new password, which can be any alpha-numeric string up to 13 characters long. The change is asserted when you press the Return key. Change Admin PasswordAllows you to set a new password.

[any alpha-numeric string up to 13 characters; admin]

Change Guest PasswordAllows you to set a new password.

[any alpha-numeric string up to 13 characters; guest]

TIP: For enhanced security, consider using misspelled words, a combi-

nation of letters and numbers, and a combination of upper and lower case letters. Also, the more characters used (up to 13), the more secure the password. These strategies help protect against sophisticated hackers who use a database of common words (for example, dictionary attacks) to determine a password. 3.7.2 Wireless Security Menu The features in the Wireless Security menu (Figure 3-64 on Page 96) control the communication of data across the wireless link. You can authenticate the radios locally via a list of authorized radios, or remotely via a centralized IEEE 802.1x device authentication server. This server provides a centralized authentication mechanism based on standards. 05-4446A01, Rev. E Mercury Reference Manual 95 Invisible place holder Figure 3-64. Wireless Security Menu Device Auth ModeView/set the devices authentication method.

[None, Local, IEEE 802.1X; None]

Data EncryptionControls the over-the-air payload datas AES-128 bit encryption. [enable, disable; disabled]

Encryption PhraseView/set the phrase used to generate encryp-

tion keys when encrypting over-the-air payload.

[any alpha-numeric string of 8 to 15 characters; <empty>]

Max Remotes (AP only)The maximum number of remotes an AP can associate with. Approved Remotes (AP only)Launches a submenu where you can view, add, or delete approved Remotes. (See Figure 3-65.) Approved Remotes Submenu Setting the Device Auth Mode to Local forces an AP to check the Approved Remotes List before establishing a radio link. A Remote must be in the list before the AP associates and grants authorization. Before enabling this option, at least one entry must already exist in the View Approved Remotes list. 96 Mercury Reference Manual 05-4446A01, Rev. E Invisible place holder Figure 3-65. Approved Remotes Submenu Add RemoteEnter the MAC address of Remote.

[Any valid 6-digit hexadecimal MAC address; 00:00:00:00:00:00]

Delete RemoteEnter the MAC address of Remote. For security purposes, you should delete a stolen or deprovisioned radio from this list. Add Associated RemotesAdd all currently associated remotes to the approved remote list. Alternatively, you can enter each Remote MAC manually. Delete All RemotesRemove (complete purge) all Remotes from current list. View Approved RemotesListing of approved Remotes by MAC address. These radios are authorized to join this AP. If a Remote is not in this list, it cannot associate with this AP. 3.7.3 IEEE 802.1x Device Authentication This section covers the configuration needed for the radios to access the IEEE 802.1x device authentication server, which provides Device Level Security and for Wireless Access Security. GE MDS does not provide the server software. Operation of Device Authentication Device authentication forces the radio to authenticate before allowing user traffic to traverse the wireless network. When Device Security is configured to use IEEE 802.1x as the Authentication Method, Remote radios need three types of certificates: public (client), private, and root

(Certificate Authority). These files are unique to each Remote radio and must first be created at the server and then installed into each unit via TFTP. The certificate files must be in DER format. Device authentication uses the serial number of each radio as the Common Name (CN) in its certificate and in its RADIUS identity field. 05-4446A01, Rev. E Mercury Reference Manual 97 Each Access Point and Remote radio must be identified/recognized by the device authentication server through the Common Name (Serial number) and IP address entries. NOTE: Consult your network administrator for assistance in configu-

ration, or for help with other issues that may arise. To activate device authentication, select Device Auth Method and set RADIUS as the active mode. The behavior of this setting differs depending on whether it is implemented on an Access Point or a Remote transceiver. An explanation of these behaviors is given below:

Access Point: When Device Auth Method is set to RADIUS, the AP disasso-

ciates all associated Remotes and waits for the device authentication server to authenticate the Remotes before allowing data from them to pass. When approval is received from the authentication server, data from the Remote passes. Remote: When Device Auth Method is set to RADIUS, the Remote halts any data it is passing, and requests Authentication from the device authenti-

cation server. If accepted, data is transmitted. Operation of User Authentication User Authentication controls authentication of users who can manage the device. This is in contrast to Device Authentication (above), which authenticates devices that can participate in the data network. When user authentication is set to Local or RADIUS, you must enter a valid user name and password before you can manage the radio. In RADIUS mode, both of these fields can be up to 40 characters long. In Local mode the user name is admin and the password can be up to 13 characters long. When set to RADIUS, all logins to the local configuration services must be authenticated via the device authentication server, including Telnet and SSH (Secure Shell) sessions. Authentication must be accepted before access to the radio menu is granted. 98 Mercury Reference Manual 05-4446A01, Rev. E RADIUS Configuration Menu Invisible place holder Figure 3-66. Radius Configuration Menu Auth Server AddressThe IP address of the authentication server. [any valid IP address; 0.0.0.0]

Auth Server PortThe UDP Port of the authentication server.

[1812, 1645, 1812]

Auth Server Shared SecretUser authentication and Device authentication require a common shared secret to complete an authentication transaction. This entry must match the string used to configure the appropriate files on the authentication server.

[<empty>; any alpha-numeric string up to 16 characters]

User Auth ModeRADIUS Authentication algorithm.

[PAP, CHAP, EAP; PAP]

NOTE: CHAP is a more secure algorithm than PAP. PAP may display the login password in log files at the authentication server while CHAP will encrypt this information. 3.7.4 Manage Certificates Use Certificate generation software to generate certificate files, then install these files into each Remote unit using TFTP. This is done using the Manage Certificates Menu (Figure 3-67 on Page 100). The certificate files must be in DER format. The Common Name (CN) field in the public certificate file must match the serial number of the unit it is installed on. 05-4446A01, Rev. E Mercury Reference Manual 99 Invisible place holder Figure 3-67. Manage Certificates Menu Invisible place holder Figure 3-68. Manage Certificates Menu, TFTP Mode

(Option Set Remote only) 100 Mercury Reference Manual 05-4446A01, Rev. E Invisible place holder Figure 3-69. Manage Certificates Menu, USB Mode

(Option Set Remote only) File MediaA selection of methods for transferring files to and from the radio. On firmware version 3.0 radios, the options are TFTP and USB. TFTP Host Address(Telnet/Terminal only)IP address of the com-

puter on which the TFTP server resides. This same IP address is used in other screens/functions (reprogramming, logging, etc.). Changing it here also changes it for other screens/functions.

[Any valid IP address; 127.0.0.1]. Transfer OptionsA menu for configuring the TFTP transfer.

(See Figure 3-70 on Page 102.) Three certificate files (Root CA, Client, and Private Key) must be present in each of the Remote radios. Use the commands described below to install these files into each Remote radio:

Certificate TypeSelects one of the three certificate file types mentioned above. [Root CA, Client, Private Key; Root CA]

Certificate FilenameSpecifies the software path and filename for downloading certificates. Retrieve CertificateInitiates the retrieval of the certificate file from the storage location. A successful installation issues a Com-

plete status message. NOTE: It is imperative that the three certificate files are installed correctly into the Remote radio, in their respective file types. If they are not, the Remote is un-authenticated for data traffic. Consult your network administrator for more information. 05-4446A01, Rev. E Mercury Reference Manual 101 Invisible place holder Figure 3-70. Transfer Options Menu TFTP TimeoutThe time the client radio will wait for a response from the server before ending the transfer. TFTP Block SizeThe amount of data sent in each TFTP packet. 3.8 REDUNDANCY CONFIGURATION

(AP ONLY) For operation in protected (redundant) mode, an AP must be in a Pack-

aged P23 enclosure with a backup radio. See MDS publication 05-4161A01 for details. This manual is available under the Downloads tab at www.GEmds.com. The Redundancy Configuration Menu (Figure 3-71) is where you enable/disable redundancy operation and define the triggers that will cause a switchover. 102 Mercury Reference Manual 05-4446A01, Rev. E Invisible place holder Figure 3-71. Redundancy Configuration Menu (AP Only) Redundancy ConfigurationEnable/disable redundancy switcho-

ver for AP. [enabled, disabled; disabled]

Network Event TriggersThis selection opens a submenu

(Figure 3-72 on Page 104) where you can set/view the trigger status for Network Events. Radio Event TriggersThis selection opens a submenu

(Figure 3-73 on Page 104) where you can set/view the trigger status for Radio Events, such as a loss of associated Remotes or excessive packet errors. Hardware Event TriggersThis selection opens a submenu

(Figure 3-74 on Page 105) where you can set/view the trigger status for initialization/hardware errors. Redundancy Configuration OptionsThis selection opens a sub-

menu (Figure 3-75 on Page 105) where you can set the thresh-

old criteria for declaring an error event. Force SwitchoverSelecting this option forces a manual (user initiated) switchover to the backup AP. The challenge ques-

tion Are you sure? (y/n) is presented to avoid an unintended switchover. To invoke the change, press the letter y followed by the Enter key. 05-4446A01, Rev. E Mercury Reference Manual 103 Network Event Triggers Menu Invisible place holder Figure 3-72. Network Events Triggers Menu Network Interface ErrorThis setting determines whether or not a network interface error will cause redundancy switchover.

[enabled, disabled; disabled]

Radio Event Triggers Invisible place holder Figure 3-73. Radio Event Triggers Lack of associated remotes exceeded thresholdThis setting deter-

mines whether or not a switchover occurs when a lack of asso-

ciated Remote units exceeds the time period set in Figure 3-76 on Page 106. [enabled, disabled; disabled]

Packet Receive Errors exceeded thresholdThis setting determines whether or not a switchover occurs when the number of Packet Receive errors exceeds the number set in Figure 3-77 on Page 106. [enabled, disabled; disabled]

104 Mercury Reference Manual 05-4446A01, Rev. E Hardware Event Triggers Invisible place holder Figure 3-74. Hardware Event Triggers Init/Hardware ErrorThis setting determines whether or not an initialization or hardware error results in a redundancy switcho-

ver. [enabled, disabled; disabled]

Redundancy Configuration Options Menu Use this menu (Figure 3-75) to set the thresholds for the Lack of Asso-

ciated Remotes and Packet Receive Errors. Selecting either item opens a submenu where you can view or change settings. Invisible place holder Figure 3-75. Redundancy Configuration Options Menu Lack of Associated Remotes Exceeded ThresholdThis selection opens a submenu (Figure 3-76) where you can view or change the time period allowed for a lack of associated Remotes. 05-4446A01, Rev. E Mercury Reference Manual 105 Packet Receive Errors Exceeded ThresholdThis selection opens a submenu (Figure 3-77 on Page 106) where you can view or change the maximum allowable number of receive errors. Invisible place holder Lack of Associated Remotes Exceeded Threshold Menu Figure 3-76. Lack of Associated Remotes Exceeded Threshold Menu Lack of Remotes forSelect this item to change the time setting

(in seconds) for a lack of associated Remotes. When there are no associated Remotes for a period exceeding this time, a redun-

dancy switchover occurs. [60-500; 500]

Invisible place holder Packet Receive Errors Exceeded Threshold Menu Figure 3-77. Packet Receive Errors Exceeded Threshold Menu Maximum Receive ErrorsSelect this item to change the maxi-

mum allowable number of receive errors. When the number of errors exceeds this number, a redundancy switchover occurs.

[0-1000; 500]

106 Mercury Reference Manual 05-4446A01, Rev. E 3.9 GPS CONFIGURATION (REMOTE ONLY) This menu allows you to view or set important parameters for the built-in Global Positioning System (GPS) receiver in the Mercury Remote. Mercury 3650 Remote units do not have or require GPS func-

tionality. Details about the NMEA sentences generated by the GE MDS Mercury can be found at http://www.nps.gov/gis/gps/NMEA_sentences.html. Invisible place holder Figure 3-78. GPS Configuration Menu (Remote Only) Stream GPS to ConsoleUsed to enable/disable streaming of GPS NMEA data to the console port (COM1). Baud rate is 4800 baud when Stream GPS to console is enabled.

[enabled, disabled; disabled]

GPS to Console Baud RateThe serial baud rate when GPS streaming is enabled. Send GPS via UDPUsed to enable/disable sending GPS NMEA data to a server via UDP. [enabled, disabled; disabled]

GPS UDP Server IP AddressSpecify the destination address for GPS NMEA UDP packets. [any valid IP address; 0.0.0.0]

GPS UDP Server UDP PortDestination UDP port for GPS NMEA UDP packets. [valid UDP port number; 0]

GPS Streaming ConfigurationA submenu for setting GPS NMEA outputs. (See Figure 3-79 on Page 108.) 05-4446A01, Rev. E Mercury Reference Manual 107 Invisible place holder Figure 3-79. GPS Streaming Configuration Menu GGA PollingSeconds between GGA string outputs, the satellite fix information. GLL PollingSeconds between GLL string outputs, the latitude and longitude information. GSA PollingSeconds between GSA string outputs, the overall satellite data. GSV PollingSeconds between GSV string outputs, the detailed satellite data. RMC PollingSeconds between RMC string outputs, the recom-

mended minimum data. VTG PollingSeconds between VTG string outputs, the vector track and speed over ground. MSS PollingSeconds between MSS string outputs, the beacon receiver status information. ZDA PollingSeconds between ZDA string outputs, data, and time. 108 Mercury Reference Manual 05-4446A01, Rev. E 3.10 DEVICE INFORMATION MENU Figure 3-80 shows the menu that displays basic administrative data on the unit to which you are connected. It also provides access to user-spe-

cific parameters such as date/time settings and device names. Figure 3-80. Device Information Menu Model (Display only) Serial Number (Display only) Uptime (Display only)Elapsed time since boot-up. DateCurrent date being used for the transceiver logs. User-set-

able. (Value lost with power failure if SNTP [Simple Network Time Protocol] server not accessible.) TimeCurrent time of day. User-setable. Setting: HH:MM:SS

(Value lost with power failure if SNTP server not accessible.) Date FormatSelect presentation format:

Generic = dd Mmm yyyy European = dd-mm-yyyy US = mm-dd-yyyy Console Baud RateUsed to set/display data communications rate (in bits-per-second) between a connected console terminal and the radio. [115200]

05-4446A01, Rev. E Mercury Reference Manual 109 UTC Time OffsetSet/view the number of hours difference between your local clock time and Universal Coordinated Time. Offsets for U.S. times zones are shown in the chart below. Time Zone

(U.S.) PST MST CST EST UTC Offset

(Hours)

-8

-7

-6

-5 Device NamesFields used at users discretion for general administrative purposes. The Device Name field is shown on all menu screen headings. (See Figure 3-81 on Page 110) NOTE: The transceivers do not save time and date information when power is removed. Device Names Menu Figure 3-81. Device Names Menu Device NameUsed by the transceiver as the Realm name for network login (web browser only) and menu headings. ContactUser defined; appears on this screen only. LocationUser defined; appears on this screen only. DescriptionUser defined; appears on this screen only. 3.11 PERFORMANCE INFORMATION MENU The Performance Information Menu (Figure 3-82 on Page 111) is the entry point for a series of submenus where you can evaluate transceiver operating status and network performance. You can use this menu as an 110 Mercury Reference Manual 05-4446A01, Rev. E important troubleshooting tool, or for evaluating changes made to the network configuration or equipment. Invisible place holder Figure 3-82. Performance Information Menu Event LogAccess this menu for managing the units opera-

tional activities log. (See Figure 3-85 on Page 113 for details.) Packet StatisticsMultiple radio and network operating statis-

tics. (See Figure 3-87 on Page 115 for details.) GPS StatusShows satellite fix status, number of satellites being received, and unit location data. (See Figure 3-88 on Page 116 for details.) Wireless Network StatusCurrent AP association state and MAC address. (See Figure 3-90 on Page 118 for details.) Internal Radio Status (Remote Only)Shows connection status, RF parameters, and total FEC count for the unit. (See Figure 3-95 on Page 120 for details.) Performance Trend (Remote Only)Launches a continuously updated list of performance parameters (RSSI, Signal-to-Noise Ratio, Transmit Power, Latitude, Longitude, Connection Status, and FEC Blocks). (See Figure 3-83 on Page 112.) Bridge StatusDisplays the network bridge status. (See Figure 3-84 on Page 112.) 05-4446A01, Rev. E Mercury Reference Manual 111 Invisible place holder Figure 3-83. Performance Trend Screen Invisible place holder Figure 3-84. Bridge Status Menu 112 Mercury Reference Manual 05-4446A01, Rev. E Event Log Menu Invisible place holder Figure 3-85. Event Log Menu Current AlarmsShows active alarms (if any) reported by the transceiver. View Event LogDisplays a log of radio events arranged by event number, date, and time. (Example shown in Figure 3-86 on Page 114). Clear Event LogErases all previously logged events. Send Event LogSends the event log to the server. You must answer the challenge question Send File? y/n before the request proceeds. Event Log Host AddressSet/display the IP address of the TFTP server. [any valid IP address; 0.0.0.0]

Event Log FilenameSet/display the name of the event log file on the TFTP server. [any valid filename; eventlog.txt]

Transfer OptionsA menu for configuring the TFTP transfer. Syslog Server AddressUse this selection to set or view the IP address of the Syslog server. Syslog is a standardized protocol for sending IP log data across a network. Low cost (or even free) Syslog downloads are available online by searching for the term Syslog Server. [any valid IP address; 0.0.0.0]

05-4446A01, Rev. E Mercury Reference Manual 113 View Event Log Menu Invisible place holder Figure 3-86. View Event Log Menu The transceivers microprocessor monitors many operational parame-

ters and logs them. Events are classified into four levels of importance, which are described in Table 3-8. Some of these events result from a condition that prevents normal operation of the unit. These are critical events that cause the unit to enter an alarmed state and the PWR LED to blink until the condition is corrected. All events are stored in the Event Log.. Table 3-8. Event Classifications Level Informational Description/Impact Normal operating activities Minor Major Does not affect unit operation Degraded unit performance but still capable of operation Critical Prevents the unit from operating The events stored in the Event Log are time-stamped using the time and date of the locally connected device. The Access Point obtains the time and date from a Time Server. This server is typically a standard Win-

dows PC server SNTP application. In the absence of the SNTP services, the user must manually enter time and date information at the Access Point. (See DEVICE INFORMATION MENU on Page 109 for SNTP server identification.) The manually set time and date clock relies on the units primary power. A loss of power resets the clock to 02 Jan 2005 but does not affect previously stored error events. Packet Statistics Menu The transceivers maintain running counters of different categories of events in the Ethernet protocol. The Packet Statistics refer to each Ethernet interface from the perspective of the radio. Time and Date 114 Mercury Reference Manual 05-4446A01, Rev. E Invisible place holder Figure 3-87. Packet Statistics Menu Packets ReceivedData packets received by this unit. Packets SentData packets sent by this unit. Bytes ReceivedData bytes received by this unit. Bytes SentData bytes sent by this unit. Packets DroppedTo-be-transmitted packets dropped because of a lack of buffers in the outbound queue. Receive ErrorsPackets that do not pass CRC. This may be due to transmissions corrupted by RF interference, Ethernet colli-

sions, or degradation. If significant Ethernet Receive Errors are observed, check the quality of your Ethernet cabling and con-

nectors, or that you do not have cable lengths exceeding the specification limits. Lost Carrier DetectedThis parameter reports how many times the wired Ethernet connection has lost link. Clear Ethernet StatisticsResets the statistics counter. You must answer the challenge question Send File? y/n before the request proceeds. Clear MDS Wireless StatisticsResets the statistics counter. You must answer the challenge question Send File? y/n before the request proceeds. 05-4446A01, Rev. E Mercury Reference Manual 115 GPS Status Menu Invisible place holder Figure 3-88. GPS Status Menu GPS Serial NumberThe serial number of the GPS unit in the radio. GPS Firmware VersionThe firmware version running on the GPS chip. Satellite Fix StatusIndicates whether or not the unit has achieved signal lock with the minimum required number of GPS satellites. The transceiver requires a fix on five satellites to achieve Precise Positioning Service (PPS) and four to maintain PPS. [No Fix, Fix]

Number of SatellitesShows the number of GPS satellites received by the transceiver. Although there are typically 24 active GPS satellites orbiting the Earth twice a day, only a sub-

set of these is visible to a receiver at a given location. A good signal provides information from six to ten satellites. LatitudeShows the transceivers latitudinal location (in degrees), based on GPS data received from the satellites. LongitudeShows the transceivers longitudinal location (in degrees), based on GPS data received from the satellites. AltitudeShows the transceivers altitude above sea level (in feet), based on GPS data received from the satellites. GPS InformationShows data about the individual satellites being received, including the Pseudo-Random Noise (PRN) code (a unique bit stream for each satellite), the satellites ele-

vation (in degrees), azimuth (in degrees), and the sig-

nal-to-noise ratio of the carrier signal (SNR). Figure 3-89 on Page 117 shows a layout example for this screen. 116 Mercury Reference Manual 05-4446A01, Rev. E GPS Information Menu Invisible place holder The Transceivers Association Process Figure 3-89. GPS Information Menu Wireless Network Status Menu The Wireless Network Status screen provides information on a key operating process of the transceiverthe association of the Remote with the Access Point. The following is a description of how this process takes place and is monitored by the menu system. If the Access Point and Remote are configured for single channel oper-

ation, the Remote monitors the channel for Access Point transmissions. The Remote synchronizes its power, timing, and frequency to the Access Point, then requests access to the network. The Access Point and Remote check each others authorization and authentication according to the configuration of the Device Authorization and Encryption Enable parameters, and the Network Name parameter. The Remote is then associ-

ated. If the Access Point and Remote are configured for frequency hopping, the Remote hops with the Access Point according to Access Points con-

figuration. Once the Remote is hopping in sync with the Access Point, the rest of the association process is the same as for single channel oper-

ation. 05-4446A01, Rev. E Mercury Reference Manual 117 Invisible place holder Figure 3-90. Wireless Network Status Menu (AP) Invisible place holder Figure 3-91. Wireless Network Status Menu (Remote) Device StatusDisplays the overall operating condition of the transceiver. [Operational, Alarmed]

Associated Remotes (AP Only)Shows the number of Remote transceivers currently associated with the AP. Remote Database (AP Only)Displays a submenu where associ-

ated Remotes are listed in table form according to their number, operational state, MAC address, IP address, and name (if assigned). (See Figure 3-92 on Page 119.) Remote Performance Database (AP Only)Displays a submenu where associated Remote performance data is listed in table form. Remotes are presented according to their number, MAC address, RSSI, SNR, modulation type, and FEC total. (See Figure 3-93 on Page 119.) 118 Mercury Reference Manual 05-4446A01, Rev. E Connection Status (Remote Only)Displays the current state of the wireless network communication as follows: Scanning, Rang-

ing, Connecting, Authenticating, Associated, or Alarmed. A complete explanation of these operating states is provided in Table 4-3 on Page 152. Current AP Eth AddressDisplays the Ethernet MAC address of the current AP. Current AP IP AddressShows the IP address of the current AP. Current AP NameDisplays the device name of the current AP. Time ConnectedShows the time at which the remote connected to the AP. The Remote has been continually connected since this time. Invisible place holder Figure 3-92. Remote Database Menu Invisible place holder Figure 3-93. Remote Performance Database Menu 05-4446A01, Rev. E Mercury Reference Manual 119 Invisible place holder Figure 3-94. Remote Database Details Menu (AP) Internal Radio Status Menu (Remote Only) Invisible place holder Figure 3-95. Internal Radio Status (Remote Only) 120 Mercury Reference Manual 05-4446A01, Rev. E Invisible place holder Figure 3-96. Internal Status Menu

(Remote in Static Hopping mode) Invisible place holder Figure 3-97. Internal Radio Status Menu

(Remote in Hopping with Handoffs Mode) NOTE: In the menu above, the items in the right hand column are displayed on Remotes only, when they are in Hopping with Handoffs mode. This allows viewing of the settings the Remote is using to connect to each AP in the AP Locations File. See Frequency Control Menu on Page 67 for explanations of these items. Exception: The Scanning Timer parameter is unique to the screen shown in Figure 3-97, and is explained below. Connection StatusIndicates whether or not the Remote station has associated with an AP.

[Associated, Scanning, Ranging, Connecting, Authorizing]

Current AP NameShows the Device Name of the current AP. 05-4446A01, Rev. E Mercury Reference Manual 121 Transmit PowerShows the RF power output from the transmit-

ter. The AP changes the transmit power of the Remote to match the desired receive power at the APs receiver. This provides end-to-end power control. Average RSSIShows average received signal strength indica-

tion (RSSI) of incoming RF signals, displayed in dBm. Average SNRShows average signal-to-noise-ratio (SNR) of received signals, displayed in dB. This is a measurement of the quality of the incoming signal. It is possible for incoming sig-

nals to be strong, yet be affected by interference or other noise, resulting in a low SNR. Use this parameter to help determine the actual quality of signals. Scanning TimerA timer that runs while the Remote radio tries to connect to a particular AP. Once this timer reaches the Max Scanning Time, the Remote tries to connect to the next AP in the AP Locations File. Radio DetailsThis selection presents a screen (Figure 3-98) showing key operating details of the transceiver. Channel StatisticsThis selection presents a screen

(Figure 3-99) that shows signal quality on a channel-by-channel basis. Readings are expressed in RSSI dBm and Signal-to-Noise Ratio (SNR) dB, respectively. Invisible place holder Figure 3-98. Radio Details Menu RSSIShows received signal strength indication (RSSI) in dBm. SNRShows signal-to-noise ratio (SNR) in dB. TX Frequency OffsetShows the RF carrier shift of the Remotes transmitter, measured in Hertz (Hz). The transmitted frequency is continually reviewed and adjusted to agree with what the AP expects to see. This optimization results in more efficient oper-

ation, corrects for doppler shift, and results in higher throughput between AP and Remote stations. 122 Mercury Reference Manual 05-4446A01, Rev. E RX Frequency OffsetThis is a measurement of how far in fre-

quency the Remotes receiver has shifted (in Hz) to accommo-

date the incoming signal from the AP. Total FEC CountThis parameter shows the total number of For-

ward Error Correction (FEC) blocks handled by the radio. Corrected FEC CountDisplays the number of errored blocks corrected with FEC by the radio. Uncorrected FEC CountShows the number of errored blocks that cant be corrected with FEC by the radio. Invisible place holder Figure 3-99. Channel Statistics Menu 3.12 MAINTENANCE/TOOLS MENU In the course of operating your network, you may wish to upgrade trans-

ceiver firmware to take advantage of product improvements, work with configuration scripts, conduct ping tests of your system, or reset oper-

ating parameters to factory default settings. All of these tasks are per-

formed using the Maintenance/Tools Menu (Figure 3-100). This section explains how to take advantage of these services. 05-4446A01, Rev. E Mercury Reference Manual 123 Invisible place holder Figure 3-100. Maintenance/Tools Menu (AP) Invisible place holder Figure 3-101. Maintenance/Tools Menu (Remote)

(Some versions may show a Scheduled Reboot option, described below) ReprogrammingManaging and selecting the units operating system firmware resources. (See Reprogramming Menu on Page 126) Configuration ScriptsSaving and importing data files contain-

ing unit operating parameters/settings. (See Conguration Scripts Menu on Page 131) Ping UtilityDiagnostic tool to test network connectivity.

(See Ping Utility Menu on Page 135) Authorization CodesAlter the units overall capabilities by enabling the built-in resources. (See Authorization Codes on Page 136) Reset to Factory DefaultsRestores parameters to factory default settings. (See Reset to Factory Defaults on Page 137) 124 Mercury Reference Manual 05-4446A01, Rev. E Radio TestA diagnostic tool for testing RF operation.

(See Radio Test Menu on Page 138) Firmware VersionsShows the firmware code versions stored in the radio and indicates which one is the active image. (See Figure 3-102 on Page 125.) Auto Firmware UpgradeBrings up a submenu where you can perform tasks related to loading new firmware. (See Auto Firmware Upgrade Menu (AP Only) on Page 138.) Telnet UtilityA submenu for opening Telnet connections to net-

work devices (Figure 3-103 on Page 125). Invisible place holder Figure 3-102. Firmware Versions Menu Figure 3-103. Telnet Utility Menu Host AddressThe IP address of the target device. ConnectConnect to the target device at the host address. 05-4446A01, Rev. E Mercury Reference Manual 125 Reprogramming Menu The factory sometimes offers upgrades to the transceiver firmware. Loading new firmware into the unit will not alter any privileges pro-

vided by Authorization Keys and does not require you to take the trans-

ceiver off-line until you want to operate the unit with the newly installed firmware image. Firmware images are available free-of-charge at:

www.GEmds.com/Resources/TechnicalSupport/

NOTE: Always read the release notes for downloaded firmware. These notes contain important information on compatibility and any special steps needed for proper installation. All units and versions have two resident images. Version 1.4.4 had two.mpk files, one for the Access Point and one for the Remote. As of version 2.1.0, there is only one mpk file which you can use with both Access Points and Remotes. The transceiver has two copies of the firmware (microprocessor code) used for the operating system and applications. One copy is active and the second is standing by, ready to be used once activated. You can load new firmware into the inactive position and place it in service whenever you desire. Invisible place holder Figure 3-104. Reprogramming Menu (AP) 126 Mercury Reference Manual 05-4446A01, Rev. E Invisible place holder Figure 3-105. Reprogramming Menu

(Option Set 1 Remote only) Invisible place holder Figure 3-106. Reprogramming Menu

(Option Set 1 Remote only) File MediaA selection of methods for transferring files to and from the radio. On firmware version 3.0 radios, the options are TFTP and USB. TFTP Host AddressIP address of the host computer from which to get the file. [Any valid IP address] This same IP address is used in other screens/functions (reprogramming, logging, etc.). Changing it here also changes it for other screens/functions. Firmware FilenameName of file to be received by the TFTP server. [Any 40-character alphanumeric string] Verify that this cor-

responds to the TFTP directory location. May require sub-direc-

tory, for example: me-bkrc-2_1_0.mpk. Transfer OptionsA menu for configuring the TFTP transfer. 05-4446A01, Rev. E Mercury Reference Manual 127 Retrieve FileInitiates the file transfer from the TFTP server. The new file is placed into inactive firmware image. [Y, N]

Image VerifyInitiate the verification of the integrity of firm-

ware file held in unit. Image CopyInitiate the copying of the active firmware into the inactive image. Reboot DeviceInitiates rebooting of the transceiver. This will interrupt data traffic through this unit, and the network if per-

formed on an Access Point. Intended to be used for switching between firmware images 1 and 2. Advanced ReprogrammingAdvanced configuration options for TFTP transfer of firmware files. See Figure 3-107 and related text descriptions. Current FirmwareDisplays the versions of firmware images installed in the transceiver and shows whether Image 1 or Image 2 is currently active. NOTE: See Upgrade Procedure on Page 130 for details on setting up the TFTP server. Invisible place holder Figure 3-107. Advanced Reprogramming Menu TFTP TimeoutView/set the time (in seconds) where no activity results in a TFTP timeout condition. TFTP Block SizeThe data size of each TFTP block being trans-

ferred to the radio during firmware upgrade. Image VerifyInitiate the verification of the integrity of firm-

ware file held in unit. Image CopyInitiate the copying of the active firmware into the inactive image. Firmware VersionsShows the available versions of firmware code for operation of the radio. 128 Mercury Reference Manual 05-4446A01, Rev. E 3.12.1 Installing Firmware via TFTP Firmware images are available free-of-charge at:

www.GEmds.com/Resources/TechnicalSupport/. NOTE: You may not install AP firmware in Remote radios, or vice-versa. This was only possible for early (pre-version 2.1.0) firmware. To install firmware by TFTP, you need:

A PC with a TFTP server running The IP address of the PC running the TFTP server A valid firmware file The IP address of the radio can be found under the Management Systems Starting Information Screen. (See Starting Information Screen on Page 42.) A TFTP server is available on the GE MDS Web site at:

www.GEmds.com/Resources/TechnicalSupport/. TIP: If you do not know your computers address on a Windows PC, you can use the RUN function from the Start menu and enter winipcfg or ipconfig to determine your local PCs IP address. There are several alternatives to connecting the transceiver for firmware upgrades. Figure 3-108 and Figure 3-109 show two variations. It is essential that all equipment be on the same subnet. LOCAL WINDOWS PC WITH CONFIG. FILES Invisible place holder TRANSCEIVER R E E N T P V L T R E F T E

& T S C ROSS-O VER CABLE LAN PORT IP ADDRESS: 172.0.0.B IP ADDRESS: 172.0.0.A INITIATE UPLOAD FROM HERE Figure 3-108. Firmware Upgrade SetupOption 1

(TFTP Server and Firmware File on Same CPU) 05-4446A01, Rev. E Mercury Reference Manual 129 REMOTE PC W/FIRMWARE FILES TFTP SERVER ETHERNET PORT Invisible place holder HUB/LAN/WAN/MAN TCP/IP TRANSCEIVER IP ADDRESS: 172.0.0.B STRAIGHT-THR U IP ADDRESS: 172.0.0.A LOCAL WINDOWS PC A B L E C LAN PORT A L A R M M I N G O R R T E P COM1, 2, ETC.

(DTE) 9 -PIN SER I A L COM1 PORT

(DCE) E L B C A IP ADDRESS: w.x.y.z INITIATE UPLOAD FROM HERE Figure 3-109. Firmware Upgrade SetupOption 2

(TFTP Server and Firmware File on Remote Server) NOTE: The LAN and COM1 ports share a common data channel when loading firmware over-the-air. Transferring the radio firmware image file ( 6 MB) might take several minutes depending on traffic between the TFTP server and the transceiver. Regardless of your connection to the transceiver, loading firm-

ware/configuration files into the units flash memory is much slower than loading software onto a PC hard drive or RAM. Upgrade Procedure To load a new firmware file (filename.mpk) into the transceiver, use the following procedure:

1. Launch a TFTP server on a PC connected either directly or via a LAN to the Ethernet port (LAN) of the radio. Point the server towards the directory containing the rmware image le. 2. Connect to the Management System by whichever means is conve-

nient: browser or Telnet via the LAN, or Terminal emulator via the COM1 port. 3. Go to the MS Reprogramming Menu.

(Main Menu>>Maintenance Menu>>Reprogramming Menu) 4. Fill in the information for the:

TFTP Host AddressIP Address of server (host computer) run-

ning TFTP server. Firmware FilenameName of file (filename.mpk) to be down-

loaded from the TFTP server holding the firmware file. 130 Mercury Reference Manual 05-4446A01, Rev. E 5. Download the rmware le from the TFTP server into the trans-

ceiver.

(Main Menu>>Maintenance Menu>>Reprogramming Menu>>Retrieve File) Status messages on the transfer are posted on the Management Sys-

tem screen. NOTE: The new firmware image file that replaces the Inactive Image file is automatically verified. 6. Reboot the transceiver. Main Menu>>Maintenance Menu>>Reprogramming Menu>>Reboot Device 7. Test the transceiver for normal operation. End of Procedure Error Messages During File Transfers It is possible to encounter errors during a file transfer. In most cases, these can be corrected by performing the actions described in Table 3-9. Table 3-9. Common Errors During TFTP Transfer Error Message Invalid File Type File not found Invalid file path Timeout Flash Error Bad CRC Likely Cause/Corrective Action Indicates that the file is not a valid firmware file. Locate proper file and re-load. Invalid or non-existent filename on TFTP server. Invalid or non-existent file path to TFTP server. TFTP transfer time expired. Increase the timeout value. Flash memory error. Contact factory for assistance. Cyclic Redundancy Check reporting a corrupted file. Attempt to re-load, or use a different file. Version String Mismatch Invalid file detected. Attempt to re-load, or use a different file. Configuration Scripts Menu A configuration script file contains all of a radios setable parameters that are accessible through the menu interface, with a few exceptions. A configuration script file is in plain text format and can be easily edited in any text program. Configuration scripts can be helpful in several ways. Three common uses for them are:

05-4446A01, Rev. E Mercury Reference Manual 131 To save known-good configuration files from your radios. These can be used for later restoration if a configuration prob-

lem occurs, and it is unclear what parameter is causing the issue. To facilitate the rapid configuration of a large number of radios. To provide troubleshooting information when you contact the factory for technical support. A technician can often spot poten-

tial problems by reviewing a configuration file. How Configuration Files Work When a configuration script file is downloaded to a radio (Retrieve File), the radio executes the parameters as commands and takes the values contained in it. When a configuration script file is uploaded from the radio (Send), it contains the current values of the radios configuration parameters. Figure 3-110 on Page 132 shows the Configuration Scripts Menu. Invisible place holder Figure 3-110. Configuration Scripts Menu 132 Mercury Reference Manual 05-4446A01, Rev. E Invisible place holder Figure 3-111. Configuration Scripts Menu

(Option Set 1 Remote only) Invisible place holder Figure 3-112. Configuration Scripts Menu

(Option Set 1 Remote only) File MediaA selection of methods for transferring files to and from the radio. On firmware version 3.0 radios, the options are TFTP and USB. Config FilenameName of file containing this units configura-

tion profile that will be transferred to the TFTP server. The con-

figuration information is in plain-text ASCII format.

[Any 40-character alphanumeric string] May require a sub-direc-

tory, for example: config\mercury-config.txt. (See Conguration Scripts Menu on Page 131 for more information.) 05-4446A01, Rev. E Mercury Reference Manual 133 NOTE: The filename field is used to identify the desired incoming file and as the name of the file exported to the TFTP server. Before exporting a units configuration, name it in a way that reflects the radios services or other identification. TFTP Host AddressIP address of the computer on which the TFTP server resides. [Any valid IP address]

Transfer OptionsA menu for configuring the TFTP transfer. CategoryThe category of parameters to send or receive. Retrieve FileInitiate the file transfer of the configuration file from TFTP server into the transceiver. Send FileInitiate the file transfer from the transceivers current configuration file to TFTP server. NOTE: See Upgrade Procedure on Page 130 for details on setting up the TFTP server. Sample of Configuration Script File A sample configuration script file is provided as part of every firmware release. Firmware images and sample files are available free-of-charge at: www.GEmds.com/Resources/TechnicalSupport/. The name of the specific file includes the firmware revision number, represented by the x characters in the following example:

mercury-config-x_x_x.txt. Editing Configuration Files Once a Remote units operation is fine-tuned, use the Conguration Scripts Menu on Page 131 to save a copy of the configuration onto a PC. Once the file is saved on the PC, you can use it as a source to generate modified copies adjusted to match other devices. Modify the configura-

tion files using a text editor or an automated process. (These applica-

tions are not provided by GE MDS). We recommend that you review and update the following parameters for each individual unit. Change other parameters as necessary. Save each resulting file with a different name. We recommend using directories and file names that reflect the location of the unit to facilitate later iden-

tification. Table 3-10. Common User-Alterable Parameters Field IP Address IP Gateway Comment Unique for each individual radio. May change for different groups or locations. Range Any legal IP address Any legal IP address 134 Mercury Reference Manual 05-4446A01, Rev. E Editing Rules Table 3-10. Common User-Alterable Parameters (Continued) Field Device Name Comment Should reflect a specific device. This information will appear in Management System headings. Range Any 20-character alphanumeric string Location Used only as reference for network administration. Any 40-character alphanumeric string Only include parameters you want to change from the default value. Change only the parameter values. Capitalization counts in some field parameters. Comment Fields:

a. Edit or delete anything on each line to the right of the comment delineator, the semicolon (;). b. Comments can be of any length, but must be on the same line as the parameter, or on a new line that begins with a semicolon character. c. Comments after parameters in files exported from a trans-

ceiver do not need to be present in your customized files. Some fields are read-only. These are designated by (RO) in the configuration sample file. Ping Utility Menu Invisible place holder Figure 3-113. Ping Utility Menu Address to PingAddress to send a Ping. [Any valid IP address]

CountNumber of Ping packets to be sent. Packet SizeSize of each Ping data packet (bytes). 05-4446A01, Rev. E Mercury Reference Manual 135 PingSend Ping packets to address shown on screen. This screen is replaced with a detailed report of Ping activity

(see example in Figure 3-114). Press any key after viewing the results to return to this menu. Invisible place holder Figure 3-114. Ping Results Screen Authorization Codes Invisible place holder Figure 3-115. Authorization Codes Menu Authorization KeyFor entering an Authorization Key into the transceivers non-volatile memory. Authorized FeaturesList of the transceivers authorized fea-

tures. Each item shows enabled or disabled according to the set-

tings allowed by the Authorization Key entered into the radio. 136 Mercury Reference Manual 05-4446A01, Rev. E Reset to Factory Defaults Use the Reset to Factory Defaults selection on the Maintenance/Tools Menu to return all configurable settings to those set at the factory prior to shipping. Use this selection with caution, as you will lose any custom settings you have established for your transceiver, and will need to re-enter them using the menu system. To prevent accidental use of the command, a challenge question is presented at the bottom of the screen when this choice is selected (see Figure 3-116 on Page 137). To proceed, enter y for yes or n for no, and then press Enter. (You may also press the Escape key on your keyboard to exit this command without making any changes.) Invisible place holder Figure 3-116. Reset to Factory Defaults Action

(Note challenge question at bottom of screen) 05-4446A01, Rev. E Mercury Reference Manual 137 3.12.2 Auto Firmware Upgrade Menu (AP Only) Invisible place holder Figure 3-117.Auto Firmware Upgrade Menu Firmware UpgradeCauses all of the Remotes associated to this AP to read the APs specified (by Firmware for Upgrade) firmware version (active or inactive), and download it via TFTP to the inactive image if the Remote does not already have that firm-

ware version. Firmware AutobootBoot connected remotes to Firmware for Upgrade (see below). Reboot RemotesDetermines how a Remote behaves once it has downloaded new firmware from the AP as part of an auto-upgrade. When enabled, the Remotes reboot to the new firmware. NOTE: To use the Auto Upgrade/Reboot feature, both the AP and Remotes must already be running version 2.1.0 or newer firm-

ware. Firmware for UpgradeSpecifies the firmware version that the Remotes should download, if they do not already have it. Radio Test Menu Using this menu, you can manually key the radio transmitter for perfor-

mance checks and set several parameters that will be used when the Radio Mode is set to Test. 138 Mercury Reference Manual 05-4446A01, Rev. E Invisible place holder Figure 3-118. Radio Test Menu NOTE : Using Test Mode disrupts traffic through the radio. If the unit is an Access Point, it will disrupt traffic through the entire network. The Test Mode function is automatically limited to 10 minutes. Only use Test Mode for brief measurements. Radio ModeSets/displays the radios operating mode. To change the setting, press A on the PCs keyboard and press the Spacebar to toggle between the two settings. Press the Enter key to select the desired state. [Normal, Test; Normal]

Test StatusThis read-only parameter shows the current state of the radio.

[Radio is Operational, Reconfiguring the Radio, Ready to KEY]

The following parameters are read-only unless A) Radio Mode is first selected and set to Test. In Test Mode, these items become selectable, and you can set their entries using the Spacebar or with a numeric entry, followed by pressing the Enter key. Test KeySets/displays keying status of the radios transmitter. Use the Spacebar to view selections. [disabled, enabled; disabled]

Test Transmit PowerSets/displays the transmitters power set-

ting. Make a numerical entry within the allowable range.

[3650 model: +23 dBm max]

[900 model: -30 to +29 dBm]

Test ChannelSets/displays the radios test channel number. Make a numerical entry within the allowable range.

[0-13; 0]

Test RF BandwidthSets/displays the transmitters bandwidth for testing. Use the Spacebar to view selections.

[1.75. 3.5 MHz; 1.75 MHzadditional selections for 3650 model]

Test Burst PercentageSets/displays the percentage of Burst size to use for testing. Make a numerical entry within the allowable range. [0-100%; 100]

05-4446A01, Rev. E Mercury Reference Manual 139 Spectrum Analyzer Menu (Remote Only) Using this menu, you can enable or disable the remotes spectrum ana-

lyzer mode (Figure 3-119 on Page 140). When enabled, the remote dis-

plays through the terminal a spectrum analyzer view of its transmit power and frequency (Figure 3-120 on Page 140). Figure 3-119. Spectrum Analyzer Menu Figure 3-120. Spectrum Analyzer Display 3.13 PERFORMANCE OPTIMIZATION After checking basic radio operation, you can optimize the networks performance. The effectiveness of these techniques varies with the design of your system and the format of the data being sent. 140 Mercury Reference Manual 05-4446A01, Rev. E There are two major areas for possible improvementthe radio and the data network. These sections provide a variety of items to check in both categories, and in many cases, ways to improve performance. NOTE: Antennas are one of the most important portions of the wire-

less system. A properly installed antenna with an unobstructed path to associated stations is the optimal conguration, and should be among the rst items checked when searching for performance gains. Stronger signals allow the use of wider bandwidths and higher data speeds with fewer retries of data transmissions. Time spent optimizing the antenna systems on both AP and Remote stations will often have a huge benet to system performance. Refer to INSTALLATION PLANNING on Page 163 for addi-

tional recommendations on antenna systems. Table 3-11 on Page 142 provides suggested settings for typical installa-

tion scenarios. These settings provide a starting point for configuration of AP and Remote units. Changes might be required to achieve the desired results in a particular situation. 05-4446A01, Rev. E Mercury Reference Manual 141 Table 3-11. Recommended Settings for Common Scenarios For Fixed Locations, where best combination of range and throughput is desired. Network Name Transmit Power

(AP)/

Max Transmit Power (RM) AP User discretion Remote User discretion 30

(3650 model: 23) 30

(3650 model: 23) Receive Power

-70 N/A Units dBm dBm Frequency Mode Frame Duration Static Hopping Static Hopping 20 20 ms Hop Pattern Hop Pattern Offset Channel Selection A, B, C, D 0-13 or 0-6 User discretion TDD Sync Mode GPS Required A, B, C, D 0-13 or 0-6 User discretion N/A Adaptive Modulation Protection Margin Hysteresis Margin Data Compression Enabled Enabled 3 3 3 3 dB dB Enabled Enabled Notes AP and Remote must match. In most cases, power can be set to this level and left alone. Setting it lower helps control cell overlap. Sets AP receiver for medium gain. Typical range: -60, -80 dBm. Changing to 10 ms lowers latency. 5 and 8 ms selections not functional for this release. AP and RM must match. AP and RM must match. Disable channels with interference. AP and RM must match. GPS Antennas must be connected to both AP and RM. Gives best throughput numbers, but may hide true performance if only tested with PING or Text File FTP. Max Modulation Cyclic Prefix Channel Type ARQ ARQ Block Size ARQ Block Lifetime ARQ TX Delay ARQ RX Delay Adaptive Split Downlink%

QAM/16-3-4 QAM16-3/4 Best combination of range and throughput. 1/16 Static Enabled 256 655 35 35 Enabled 50 N/A N/A N/A N/A N/A N/A N/A N/A N/A Best throughput setting. Less periodic ranging when channel type is Static. bytes ms ms ms

These 3 settings make the max. no. of ARQ retries =9.

(655 ms)/(35 ms + 35 ms = 9.35=>9 Maximizes one-way burst throughput. If Adaptive Split is disabled, can set downlink% to 15%75%. n o i t a r u g i f n o C o d a R i l o r t n o C y c n e u q e r F n o i t a r u g i f n o C d e c n a v d A 142 Mercury Reference Manual 05-4446A01, Rev. E

(Trades off throughput for best possible sensitivity. AP more susceptible to interference) For Optimal Sensitivity Radio Configuration Receive Power AP

-80 Remote N/A Units dBm Sets AP receiver for highest gain. Notes When Heavy Interference Exists at AP

(Trades off range for robustness in the face of interference) Radio Configuration Receive Power AP

-60 Remote N/A Notes Units dBm Sets AP receiver for low gain, which forces Remote transmit power to be high. For Mobile Systems

(Where hand-offs between APs are required) Radio Configuration Frequency Control Advanced Configuration Frequency Mode Protection Margin AP Static Hopping 6 Units Notes Remote Hopping w/Hand-offs 6 dB Channel Type Dynamic N/A Network Configuration AP Location Info Config Retrieve Text File N/A AP Locations file More channel variation in mobile, so use more robust modulation with greater SNRs. Less periodic ranging when Channel Type = Static. AP locations file with coordinates and key attributes of APs to which Remote can associate. 3.13.1Proper Operation and What to Look For Table 3-12 and Table 3-13 on Page 144 show target performance values for AP and Remote transceivers. View these values using the built-in menu system by navigating the path shown under each table title. Table 3-12. Mercury Remote Transceiver

(Performance Information>>Internal Radio Status Menu) Name Connection Status Target Value Associated Transmit Power RSSI

(Received Signal Strength Indication) Varies Varies Notes Remote must be associated for network operation. Adjusts automatically as requested by AP. The less negative an RSSI reading, the stronger the signal (i.e., -75 dBm is stronger than -85 dBm). 05-4446A01, Rev. E Mercury Reference Manual 143 Table 3-12. Mercury Remote Transceiver (Continued)

(Performance Information>>Internal Radio Status Menu) Name SNR

(Signal-to-Noise Ratio) Target Value Strong signal (bench setting): 25-28 dB Notes A low SNR may be caused by noise or interfering signals. Operational: 3-30 dB Typ. System: 10-20 dB TX Freq. Offset 0-22,875 Hz RX Freq. Offset 0-22,875 Hz Adjusts to accommodate what is expected by the AP. Adjusts to accommodate what is expected by the AP. Total FEC Count Corrected FEC Count Uncorrected FEC Count Current AP Name Varies Varies Varies Device name of associated AP Typically set to reflect the application or system the radio is used in. Table 3-13. Mercury Access Point

(Performance Information>>Wireless Network Status>>

Remote Performance Database) Name MAC ADDR RSSI

(Received Signal Strength Indication) Target Value MAC Address of associated Remote Varies Notes Must match Remotes MAC address exactly The less negative an RSSI reading, the stronger the signal (i.e., -75 dBm is stronger than -85 dBm). SNR Signal-to-Noise Ratio Strong signal (bench):

25-28 dB A low SNR may be caused by noise or interfering signals. Operational: 3-30 dB Typ. System:10-20 dB Downlink Uplink FEC Total Corrected FEC Count Uncorrected FEC Count Varies Varies Varies Varies Varies QPSK/FEC-3/4 Preferred QPSK/FEC-3/4 Preferred Additional Considerations for Mobile Operation Consider the following key points for all mobile installations:

144 Mercury Reference Manual 05-4446A01, Rev. E NOTE: 3650 MHz is for APs and Fixed Remote stations only. Use connectionwareThe use of connectionware in the mobile lap-

tops is highly recommended for better operation of a mobile data system. GE MDS provides connectionware from one of the vendors in this market. Contact your factory representative for details. Plan your network coverageDeploy Access Points so that they provide overlapping coverage with each other. Access Points must use the same Network Name to enable roaming service. Set the RSSI Threshold to -70 dBmThis level is typically used for mobile systems with good performance. Make sure there is overlap-

ping coverage of more than one AP to provide continuous coverage. At every AP Radio, review the following settings when providing service to mobile remotes:

TDD SyncSet to GPS Required. Pattern OffsetEach AP should be different. Cell planning is required if there are overlaps. Hop PatternSet the same on all APs. Compression [disabled]Disable radio compression. Data com-

pression is best performed by the connectionware running on the mobile laptop PC. Gains in efficiency are made because connectionware compresses data at a higher stack level, and it aggregates multiple data frames and streams into a single packet. Compression at the radio level, although highly effi-

cient, works only at the individual packet level. 05-4446A01, Rev. E Mercury Reference Manual 145 146 Mercury Reference Manual 05-4446A01, Rev. E 4 TROUBLESHOOTING &

RADIO MEASUREMENTS 4 Chapter Counter Reset Paragraph Contents 4.1 TROUBLESHOOTING.............................................................149 4.1.1 Interpreting the Front Panel LEDs ...........................................149 4.1.2 Troubleshooting With the Embedded Management System ....150 4.1.3 Using Logged Operation Events ..............................................153 4.1.4 Alarm Conditions ......................................................................154 4.1.5 Correcting Alarm Conditions ....................................................155 4.1.6 Logged Events .........................................................................155 4.2 RADIO (RF) MEASUREMENTS..............................................157 4.2.1 Antenna System SWR and Transmitter Power Output ............157 4.2.2 Antenna AimingFor Directional Antennas .............................158 05-4446A01, Rev. E Mercury Reference Manual 147 148 Mercury Reference Manual 05-4446A01, Rev. E Multiple Communication Layers Unit Configuration Factory Assistance 4.1 TROUBLESHOOTING Successful troubleshooting of a wireless system is not difficult, but requires a logical approach. It is best to begin troubleshooting at the Access Point unit, as the rest of the system depends on the Access Point for synchronization data. If the Access Point has problems, the operation of the entire wireless network is affected. When you find communication problems, it is good practice to begin by checking the simple causes. Applying basic troubleshooting techniques in a logical progression identifies many problems. It is important to remember that the operation of the network is built on a radio communications link. On top of that are two data levels wire-

less MAC, and the data layer. It is essential that the wireless aspect of the Access Point and the Remotes units to be associated operates prop-

erly before data-layer traffic will function. There are numerous user-configurable parameters in the Management System. Do not overlook the possibility that human error is the cause of the problem. With so many parameters to view and change, a parameter might be incorrectly set, and then that change is forgotten. To help avoid these problems, GE MDS recommends creating an archive of the transceivers profile in a Configuration File when your installation is complete. You can reload this file into the transceiver to restore the unit to the factory defaults or your unique profile. For details on creating and archiving Configuration Files, see Conguration Scripts Menu on Page 131. If problems cannot be resolved using the guidance provided here, review the GE MDS web sites technical support area for recent soft-

ware/firmware updates, general troubleshooting help, and service infor-

mation. Additional help is available through our Technical Support Department. (See TECHNICAL ASSISTANCE on the inside of the rear cover.) 4.1.1 Interpreting the Front Panel LEDs An important set of troubleshooting tools are the LED status indicators on the front panel of the radio case. You should check them first when-

ever a problem is suspected. Table 2-2 on Page 30 describes the func-

tion of each status LED. Table 4-1 on Page 150 provides suggestions for 05-4446A01, Rev. E Mercury Reference Manual 149 resolving common system difficulties using the LEDs, and Table 4-2 on Page 151 provides other simple techniques. Table 4-1. Troubleshooting Using LEDsSymptom-Based Symptom PWR LED does not turn on Problem/Recommended System Checks a. Voltage too lowCheck for the proper supply voltage at b. the power connector. (1030 Vdc) Indefinite ProblemCycle the power and wait

( 30 seconds) for the unit to reboot. Then, recheck for normal operation. LINK LED does not turn on a. Network Name of Remote not identical to desired Access PointVerify that the system has a unique Network Name. b. Not yet associated with an Access Point with the same Network Name. Check the Status of the units process of associating with the Access Point. Use the Management System. c. Poor Antenna SystemCheck the antenna, feedline and connectors. Reflected power should be less than 10% of the forward power reading (SWR 2:1 or lower). a. Blinking indicates that an alarm condition exists. b. View Current Alarms and Event Log and correct the problem if possible.

(See Using Logged Operation Events on Page 153) c. Blinking continues until the source of the alarm is corrected, for example, a valid IP address is entered, etc. a. Verify the Ethernet cable is connect at both ends. b. Verify that the appropriate type of Ethernet cable is used:

straight-through or crossover. PWR LED is blinking LAN LED does not turn on LAN LED lights, but turns off after some time Verify traffic in LAN. Typically, the radio should not be placed in high traffic enterprise LANs, as it will not pass this level of traffic. If needed, use routers to filter traffic. GPS LED not lit No satellite fix has been obtained. A fix is required for all operation except single-frequency channel (non-hopping) configurations. The lack of a fix may be caused by an obstructed view of the satellites, or a GPS antenna problem. The GPS LED blinks slowly on the AP while it synchronizes its internal clock to the GPS signal. When in this condition, the AP does not transmit. 4.1.2 Troubleshooting With the Embedded Management System If you have reviewed and tried the items listed in Table 4-1 and still have not resolved the problem, there are additional tools and techniques you can use. The embedded Management System is a good source of infor-

mation that you can use remotely to provide preliminary diagnostic information, or may even provide a path to correcting the problem. Refer to Table 4-2 on Page 151 for more information on using the Man-

agement System as a troubleshooting tool. 150 Mercury Reference Manual 05-4446A01, Rev. E Table 4-2. Basic Troubleshooting Using the Management System Symptom Cannot access the MS through COM1 Display on terminal/Telnet screen garbled Password forgotten Problem/Recommended System Checks a. Connect to unit via Telnet or Web browser. b. Disable the serial mode for COM1

(Serial Gateway Configuration>>Com1 Serial Data Port>>Status>>Disabled). Or, if you know the units data configuration:

a. Connect to COM 1 via a terminal set to VT100 and the ports data baud rate. b. Type +++. c. Change the terminals baud rate to match the transceivers Console Baud Rate. d. Type +++. Verify the terminal/terminal emulator or Telnet application is set to VT100. a. Connect to the transceiver using a terminal through the b. COM1 Port. Obtain a password-resetting Authorization Key from your factory representative. c. At the login prompt, try the user name authcode, and enter the Authorization Key for the password. Remote only gets to Connecting a. Check Network Name, encryption, and Device Auth Mode settings. Remote only gets to Authenticating Cannot pass IP data to WAN Wireless Retries too high b. Verify that the correct MAC address is listed in the Approved Remotes List of the Security Configuration Menu. Check encryption settings and security mode settings. a. Verify your IP settings. b. Use the PING command to test communication with the transceivers in the local radio system. If successful with local PING, attempt to PING an IP unit attached to a transceiver. If successful with the LAN PINGs, try connecting to a known good unit in the WAN. c. d. Possible Radio Frequency Interference:

a. If omnidirectional antennas are used, consider changing to directional antennas. This usually limits interference to and from other stations. b. Try disabling channels where persistent interference is known or suspected. c. The installation of a filter in the antenna feedline may be necessary. Consult the factory for further assistance. d. Try using an antenna with a downward tilt. The following is a summary of how you can use several screens in the Management System as diagnostic tools. For information on how to 05-4446A01, Rev. E Mercury Reference Manual 151 connect to the Management System, see STEP 3: CONNECT PC TO THE TRANSCEIVER on Page 25. Starting Information Screen

(See Starting Information Screen on Page 42) The Management Systems home page provides some valuable bits of data. One of the most important is the Device Status field. This item tells you if the unit is operational. If the Device Status field says Associated, then look in the network areas beginning with network data statistics. If it displays some other mes-

sage, such as Scanning, Connecting, or Alarmed, you must determine why it is in this state. The Scanning state indicates a Remote unit is looking for an Access Point beacon signal to lock onto. It should move to the Connecting state and finally to the Associated state within less than a minute. If this Remote unit is not providing reliable service, look at the Event Logs for signs of lost association with the Access Point, or low signal alarms. Table 4-3 provides a description of the Device Status messages. Scanning Ranging Connecting Authenticating2 Associated Alarmed Table 4-3. Device Status1 The unit is looking for an Access Point beacon signal. Remote has detected AP and is synchronizing to it. The Remote has established a radio (RF) connection with the Access Point and is negotiating the network layer connectivity. The Remote is authenticating itself to the network to obtain cyber-security clearance in order to pass data. This unit has successfully synchronized and is associated with an Access Point. This is the normal operating state. The unit has detected one or more alarms that have not been cleared. 1. Device Status is available in the Startup Information Screen or the Wireless Status Screen at Remotes. 2. If Device Authentication is enabled. If the Remote is in an Alarmed state, the unit might still be operational and associated. Look for the association state in the Wireless Network Status screen to determine if the unit is associated. If it is, look at the Error Log for possible clues. If the unit is in an Alarmed state and is not associated with an Access Point, then there might be a problem with the wireless network layer. Call a radio technician to deal with wireless issues. Refer the technician to the RADIO (RF) MEASUREMENTS on Page 157 for information on antenna system checks. 152 Mercury Reference Manual 05-4446A01, Rev. E Packet Statistics Menu

(See Packet Statistics Menu on Page 114) This screen provides detailed information on data exchanges between the unit being viewed and the network through the wireless and the Ethernet (data) layers. These include:

Wireless Packet Statistics Packets received Packets sent Bytes received Bytes sent Ethernet Packet Statistics Packets received Packets sent Bytes received Bytes sent Lost carrier detected Packets dropped Receive errors Retries Retry errors Packets dropped Receive errors Retries Retry errors The most significant fields are the Packets Dropped, Retries, Retry Errors, Receive Errors and Lost Carrier Detected. If the data values are more than 10% of their sent and received counterparts, or the Lost Car-

rier Detected value is greater than a few dozen, there might be trouble with radio-frequency interference or a radio link of marginal strength. If errors are excessive, check the aiming of the antenna system, and check for a satisfactory SWR. Refer to RADIO (RF) MEASUREMENTS on Page 157 for information on antenna system checks. Diagnostic Tools

(See MAINTENANCE/TOOLS MENU on Page 123) The radios Maintenance menu contains two tools that are especially useful to network techniciansthe Radio Test Menu and the Ping Utility. Use the Radio Test selection for testing RF operation. Use the Ping Utility to verify communications access to pieces of equipment connected to the radio network. This includes transceivers and user-sup-

plied Ethernet devices. 4.1.3 Using Logged Operation Events

(See PERFORMANCE INFORMATION MENU on Page 110) The transceivers microprocessor monitors many operational parame-

ters and logs them as various classes of events. If the event is one that affects performance, it is an alarm. There are also normal or routine events such as those marking the rebooting of the system, implementa-

tion of parameter changes, and external access to the Management System. Informational events are stored in temporary (RAM) memory that is lost in the absence of primary power, and Alarms are stored in 05-4446A01, Rev. E Mercury Reference Manual 153 permanent memory (Flash memory) until cleared by user request. Table 4-4 summarizes these classifications. Table 4-4. Event Classifications Level Alarms Description/Impact Transceiver has detected one or more alarm conditions Informational Normal operating activities Storage Flash Memory Flash Memory Temporary Informational Minor Major Transient conditions or events RAM Does not affect unit operation Degraded unit performance but still capable of operation RAM RAM Critical Prevents the unit from operating RAM These events are stored in the transceivers Event Log and can be a valu-

able aid in troubleshooting unit problems or detecting attempts at breaching network security. 4.1.4 Alarm Conditions Most events, classified as critical will cause the PWR LED to blink, and will inhibit normal operation of the transceiver. The LED blinks until the corrective action is completed. (See also Event Log Menu on Page 113.) Table 4-5. Alarm Conditions (Alphabetical Order) Alarm Condition Reported EVENT_BRIDGE Event Log Entry Network Interface /Error SNMP Trap networkInterface(17) EVENT_FREQ_CAL EVENT_INIT_ERR EVENT_IPADDR*

EVENT_IPMASK*

EVENT_LAN_PORT EVENT_MAC Frequency Not Calibrated frequencyCal(7) Initialization Error initializationError(18) IP Address Invalid ipAddressNotSet(4) IP Mask Invalid ipNetmaskNotSet(5) MAC communication Failed lanPortStatus(78) macCommunication(1) EVENT_MACADDR MAC Address Invalid noMacAddress(6) EVENT_NETNAME*

EVENT_POWER_CAL EVENT_REMOTE EVENT_RSSI*

Netname Invalid invalidNetname(12) Power Calibrated/Not Calibrated Remote Added/

Removed (AP Only) RSSI Exceeds threshold powerCal(8) eventRemote(66) rssi(11) 154 Mercury Reference Manual 05-4446A01, Rev. E Table 4-5. Alarm Conditions (Alphabetical Order) (Continued) Alarm Condition Reported EVENT_RSSI_CAL Event Log Entry RSSI Not Calibrated SNMP Trap rssiCal(9) EVENT_SYSTEM_ERROR*

EVENT_TFTP_CONN System Error Cleared;

Please Reboot TFTP connectivity achieved EVENT_TFTP_ERR Attempted TFTP connection failed

* User can correct condition, clearing the alarm. systemError(16) tftpConnection(73) tftpConnFailed(79) 4.1.5 Correcting Alarm Conditions

(See Event Log Menu on Page 113) Table 4-6 provides likely causes of events that inhibit the unit from operating, and possible corrective actions. The Event Description column appears on the Event Log screen. Table 4-6. Correcting Alarm ConditionsAlphabetical Order Event Log Entry Generating Condition Bridge Down General System Error Initialization Error The Bridge fails to be initialized. Internal checks suggest unit is not functioning properly. Clearing Condition or Action Contact factory Technical Services for assistance. Reboot the transceiver. Unit fails to complete boot cycle. Contact factory Technical Services for assistance. Invalid IP Address The IP address is either 0.0.0.0 or 127.0.0.1. Program IP address to something other than 0.0.0.0 or 127.0.0.1. Network Interface Error Unit does not recognize the LAN interface. Contact factory Technical Services for assistance. RSSI Exceeds Threshold The running-average RSSI level is weaker (more negative) than the user-defined value. Check the aiming of the directional antenna at the Remote; raise the threshold level to a stronger

(less-negative) value. 4.1.6 Logged Events The following events allow the transceiver to continue operation and do not make the PWR LED blink. Each is reported through an SNMP trap. 05-4446A01, Rev. E Mercury Reference Manual 155 The left hand column, Event Log Entry, is what shows in the Event Log.

(See also Event Log Menu on Page 113.) Table 4-7. Non-Critical EventsAlphabetical Order Event Log Entry Association Attempt Success/Failed Association Lost - Local IP Address Changed Association Lost - Local Network Name Changed Association Lost/Established Auth Demo Mode Expired --

Rebooted Radio/Enabled Auth Key Entered - Key Valid/Key Invalid Console Access Locked for 5 Min Console User Logged Out/Logged In Current AP No Longer Approved Severity MAJOR Description Self explanatory MAJOR Self explanatory MAJOR Self explanatory MAJOR MAJOR Self explanatory Self explanatory MAJOR Self explanatory MAJOR Self explanatory MAJOR Self explanatory MAJOR May occur during the Scanning process at a Remote. Indicates that the received beacon came from an AP which is not in the Approved AP list. This might be caused by some Remotes hearing multiple AP's. This event is expected behavior. A decryption error is logged when an encryption phrase mismatch has occurred. A mismatch is declared after five consecutive errors over a 40-second window. When the error has cleared, DECRYPT OK appears. Self explanatory Self explanatory Self explanatory Decryption Error/Decryption OK MAJOR Ethernet Port Enabled/Disabled Ranging Lost/Established Connecting Lost/Established INFORM INFORM INFORM HTTP Access Locked for 5 Min MAJOR Self explanatory HTTP User Logged Out/Logged In Log Cleared Reprogramming Complete Reprogramming Failed Reprogramming Started Scanning Started SNR Within threshold/Below threshold MAJOR httpLogin(49) INFORM INFORM MAJOR INFORM INFORM INFORM Self explanatory Self explanatory Self explanatory Self explanatory Self explanatory Self explanatory 156 Mercury Reference Manual 05-4446A01, Rev. E Table 4-7. Non-Critical EventsAlphabetical Order (Continued) Event Log Entry System Bootup (power on) Telnet Access Locked for 5 Min Telnet User Logged Out/Logged In Severity INFORM MAJOR Description Self explanatory Self explanatory MAJOR Self explanatory User Selected Reboot MAJOR Self explanatory 4.2 RADIO (RF) MEASUREMENTS There are several measurements that should be performed during the ini-

tial installation. These measurements confirm proper operation of the unit and, if they are recorded, serve as a benchmark in troubleshooting should difficulties appear in the future. These measurements are:

Transmitter Power Output Antenna System SWR (Standing-Wave Ratio) Antenna Direction Optimization These procedures might interrupt traffic through an established network and should only be performed by a skilled radio-technician in coopera-

tion with the Network Administrator. 4.2.1 Antenna System SWR and Transmitter Power Output Introduction A proper impedance match between the transceiver and the antenna system is important. It ensures the maximum signal transfer between the radio and antenna. You can check the impedance match indirectly by measuring the SWR (standing-wave ratio) of the antenna system. If the results are normal, record them for comparison during future routine preventive maintenance. Abnormal readings indicate possible trouble with the antenna or the transmission line, and should be corrected. Check the SWR of the antenna system before putting the radio into reg-

ular service. For accurate readings, a wattmeter suited to the frequency of operation is required. One unit meeting this criteria is the Bird Model 43 directional wattmeter with the appropriate element installed. The reflected power should be less than 10% of the forward power

(2:1 SWR). Higher readings indicate problems with the antenna, feed-

line or coaxial connectors. Record the current transmitter power output level, then set it to an ade-

quate signal level for the directional wattmeter (for the duration of the test.) 05-4446A01, Rev. E Mercury Reference Manual 157 Procedure 1. Place a directional wattmeter between the TX antenna connector and the antenna system. 2. Place the transceiver into the Radio Test Mode using the menu sequence below:

(Maintenance/Tools Menu>>Radio Test>>Radio Mode>>Test) 3. Set the transmit power to 29 dBm (900 model), or 23 dBm (3650 model). (This setting does not affect the output level during normal operationonly during Test Mode.)

(Maintenance/Tools Menu>>Radio Test >>Test Mode>>Test>>Test Transmit Power) 4. Key the transmitter.

(Maintenance/Tools Menu>>Radio Test>>Test Mode>>Test>>Test Key>>

enabled) Use the PCs spacebar to key and unkey the transmitter.

(Enable/Disable) NOTE: The Transmit Key has a 10-minute timer, after which it unkeys the radio. Manually unkey the transmitter by selecting Test Key>>disabled on the menu, or temporarily disconnecting the radios DC power. 5. Measure the forward and reected power into the antenna system and calculate the SWR and power output level. The output should agree with the programmed value set in the Radio Conguration Menu. (Radio Configuration>>Transmit Power) 6. Turn off Radio Test Mode.

(Maintenance/Tools Menu>>Radio Test>>Test Key>>disabled) End of procedure. 4.2.2 Antenna Aiming (For Directional Antennas) Introduction The radio network integrity depends, in a large part, on stable radio signal levels at each end of a data link. In general, signal levels stronger than 80 dBm provide the basis for reliable communication that includes a 15 dB fade margin. As the distance between the Access Point and Remotes increases, the influence of terrain, foliage, and man-made obstructions become more influential, and the use of directional antennas at Remote locations becomes necessary. Directional antennas require fine-tuning of their bearing to optimize the received signal strength. The transceiver has a built-in received signal strength indicator

(RSSI) that can tell you when the antenna is in a position that provides the optimum received signal. 158 Mercury Reference Manual 05-4446A01, Rev. E RSSI measurements and Wireless Packet Statistics are based on mul-

tiple samples over a period of several seconds. The average of these measurements is displayed by the Management System. The measurement and antenna alignment process usually takes 10 or more minutes at each radio unit. The path to the Management System menu item is shown in bold text below each step of the procedure. Procedure 1. Verify the Remote transceiver is associated with an Access Point unit by observing the condition of the LINK LED (LINK LED = On or Blinking). This indicates that you have an adequate signal level for the measurements and it is safe to proceed. 2. Record the Wireless Packets Dropped and Received Error rates.

(Main Menu>>Performance Information>>Packet Statistics>>Wireless Packet Statistics) This information will be used later. 3. Clear the Wireless Packets Statistics history.

(Main Menu>>Performance Information>>Packet Statistics>>Wireless Packet Statistics>>Clear Wireless Stats) 4. Read the RSSI level at the Remote.

(Main Menu>>Performance Information>>Internal Radio Status) 5. Optimize RSSI (less negative is better) by slowly adjusting the direction of the antenna. Watch the RSSI indication for several seconds after making each adjustment so that the RSSI accurately reects any change in the link signal strength. 6. View the Wireless Packets Dropped and Received Error rates at the point of maximum RSSI level. They should be the same or lower than the previous reading.

(Main Menu>>Performance Information>>Packet Statistics>>Wireless Packet Statistics) 05-4446A01, Rev. E Mercury Reference Manual 159 7. If the RSSI peak results in an increase in the Wireless Packets Dropped and Received Error, the antenna may be aimed at an undes-

ired signal source. Try a different antenna orientation. End of procedure. 160 Mercury Reference Manual 05-4446A01, Rev. E 5 PLANNING A RADIO NETWORK 5 Chapter Counter Reset Paragraph Contents 5.1 INSTALLATION PLANNING163 5.1.1 General Requirements 163 5.1.2 Site Selection 164 5.1.3 Terrain and Signal Strength 165 5.1.4 Antenna & Feedline Selection 165 5.1.5 How Much Output Power Can be Used? 169 5.1.6 Conducting a Site Survey 169 5.1.7 A Word About Radio Interference 170 5.1.8 ERP Compliance at 900 MHz 172 5.1.9 ERP Compliance at 3650 MHz 173 5.2 dBm-WATTS-VOLTS CONVERSION CHART174 05-4446A01, Rev. E Mercury Reference Manual 161 162 Mercury Reference Manual 05-4446A01, Rev. E 5.1 INSTALLATION PLANNING This section provides tips for selecting an appropriate site, choosing an antenna system, and reducing the chance of harmful interference. 5.1.1 General Requirements There are three main requirements for installing a transceiverade-

quate and stable primary power, a good antenna system, and the correct interface between the transceiver and the data device. Figure 5-1 shows a typical Remote installation. NOTE: The transceivers network port supports 10BaseT and 100BaseT connections. Confirm that your hub/switch is capable of auto-switching data rates. To prevent excessive Ethernet traffic from degrading perfor-

mance, place the transceiver in a segment, or behind routers. Invisible place holder ANTENNA SYSTEM TRANSCEIVER Network E D LI N E E S F S O W -L O L COMPUTER RUNNING TERMINAL PROGRAM POWER SUPPLY 13.8 VDC @ 580 mA (Max.)

(10.530 Vdc) Negative Ground Only Figure 5-1. Typical Fixed Remote Installation With a Directional Antenna

(Connect user data equipment to any compatible LAN Port) Unit Dimensions Figure 5-2 on Page 164 shows the dimensions of the transceiver case and its mounting holes, and Figure 5-3 on Page 164 shows the dimen-

sions for mounting with factory-supplied brackets. If possible, choose a 05-4446A01, Rev. E Mercury Reference Manual 163 mounting location that provides easy access to the connectors on the end of the radio and an unobstructed view of the LED status indicators.

) m c 3 4

. 1 1

5

. 4 1.4

(3.56 cm) 6.75 (17.15 cm) Figure 5-2. Transceiver Dimensions Invisible place holder Invisible place holder TOP VIEW FRONT VIEW

) m c 7

5 7

. 2 8 5/8 (21.8 cm) Figure 5-3. Mounting Bracket Dimensions (center to center) NOTE: To prevent moisture from entering the radio, do not mount the radio with the cable connectors pointing up. Also, dress all cables to prevent moisture from running along the cables and into the radio. 5.1.2 Site Selection Suitable sites should provide:

Protection from direct weather exposure 164 Mercury Reference Manual 05-4446A01, Rev. E A source of adequate and stable primary power Suitable entrances for antenna, interface, or other required cabling An antenna location that provides a transmission path that is as unobstructed as possible in the direction of the associated sta-

tion(s) With the exception of the transmission path, you can quickly determine these requirements. Radio signals travel primarily by line-of-sight, and obstructions between the sending and receiving stations will affect system performance. If you are not familiar with the effects of terrain and other obstructions on radio transmission, the discussion below will provide helpful background. 5.1.3 Terrain and Signal Strength While the license-free bands offers many advantages for data transmis-

sion services, signal propagation is attenuated by obstructions such as terrain, foliage, or buildings in the transmission path. A line-of-sight transmission path between the central transceiver and its associated remote site(s) is highly desirable and provides the most reliable commu-

nications link. Much depends on the minimum signal strength that can be tolerated in a given system. Although the exact figure will differ from one system to another, a Received Signal Strength Indication (RSSI) of 80 dBm or stronger will provide acceptable performance in most systems. While the equipment will work at lower-strength signals, signals stronger than 77 dBm provide a fade margin of 15 dB to account for variations in signal strength that might occur. You can measure RSSI with a terminal connected to the COM1 port, or with an HTTP browser connected to the LAN (Ethernet) connector. (See Antenna Aiming (For Directional Antennas) on Page 158 for details.) 5.1.4 Antenna & Feedline Selection NOTE: The transceiver must be installed by trained professional installers, or factory trained technicians. The following text will help the professional installer in the proper methods of maintaining compliance with regulatory ERP limits. Antennas The radio equipment can be installed with a number of antennas. The exact style used depends on the physical size and layout of a system. Contact your factory representative for specific recommendations on antenna types and hardware sources. 05-4446A01, Rev. E Mercury Reference Manual 165 In general, an omnidirectional antenna (Figure 5-4) is used at the Access Points and mobile Remote stations. This provides equal signal coverage in all directions. NOTE: Antenna polarization is important. If the wrong polarization is used, a signal reduction of 20 dB or more will result. Most systems using a gain-type omnidirectional antenna at Access Point stations employ vertical polarization of the signal; there-

fore, the Remote antenna(s) must also be vertically polarized

(elements oriented perpendicular to the horizon). When required, horizontally polarized omnidirectional antennas are also available. Contact your factory representa-

tive for details. Invisible place holder High-gain Type Unity-gain Type Figure 5-4. Typical Omnidirectional Antennas At fixed Remote sites, a directional Yagi antenna (Figure 5-5 on Page 166) minimizes interference to and from other users. Antennas are available from a number of manufacturers. Invisible place holder Figure 5-5. Typical Yagi Antenna (mounted to mast) 166 Mercury Reference Manual 05-4446A01, Rev. E Diversity Reception (RX2) Antenna Port Functional on some models. The RX2 antenna port allows connection of a second antenna to the transceiver for space diversity reception. GPS Antennas A number of GPS antennas (both active and passive) are available for use with the transceivers. Consult your factory representative for more information. Feedlines Carefully consider the choice of feedline used with the antenna. Avoid poor-quality coaxial cables, as they degrade system performance for both transmission and reception. A low-loss cable type such as Heliax is recommended that is suitable for the frequency of operation. Keep the cable as short as possible to minimize signal loss. Table 5-1 lists several types of popular feedlines and indicates the signal losses (in dB) that result when using various lengths of cable at 900 MHz. The choice of cable depends on the required length, cost con-

siderations, and the acceptable amount of signal loss. Table 5-1 lists Table 5-1. Length vs. Loss in Coaxial Cables at 900 MHz Cable Type RG-214 10 Feet

(3.05 m)

.76 dB 50 Feet

(15.24 m) 3.8 dB 100 Feet

(30.48 m) 7.6 dB LMR-400 0.39 dB 1.95 dB 3.90 dB 500 Feet

(152.4 m) Unacceptable Loss Unacceptable Loss 1/2 inch HELIAX 7/8 inch HELIAX 0.23 dB 0.13 dB 1-1/4 inch HELIAX 0.10 dB 1-5/8 inch HELIAX 0.08 dB 1.15 dB 0.64 dB 0.48 dB 0.40 dB 2.29 dB 1.28 dB 0.95 dB 0.80 dB 11.45 dB 6.40 dB 4.75 dB 4.00 dB several types of popular feedlines and indicates the signal losses (in dB) that result when using various lengths of cable at 900 MHz. The choice of cable depends on the required length, cost considerations, and the acceptable amount of signal loss. Table 5-2. Length vs. Loss in Coaxial Cables at 3600 MHz Cable Type RG-214 10 Feet

(3.05 m) 3.04 dB 50 Feet

(15.24 m) 15.2 dB 100 Feet

(30.48 m) Unacceptable Loss 500 Feet

(152.4 m) Unacceptable Loss LMR-400 1.56 dB 7.8 dB 15.6 dB Unacceptable Loss 05-4446A01, Rev. E Mercury Reference Manual 167 Table 5-2. Length vs. Loss in Coaxial Cables at 3600 MHz Cable Type 1/2 inch HELIAX 10 Feet

(3.05 m) 0.92 dB 7/8 inch HELIAX 0.52 dB 1-1/4 inch HELIAX 0.40 dB 50 Feet

(15.24 m) 4.6 dB 2.56 dB 1.92 dB 1-5/8 inch HELIAX 0.32 dB 1.6 dB 100 Feet

(30.48 m) 9.16 dB 5.12 dB 3.8 dB 3.2 dB 500 Feet

(152.4 m) Unacceptable Loss Unacceptable Loss 19 dB 16 dB The tables below outline the minimum lengths of RG-214 coaxial cable that must be used with common GE MDS omnidirectional antennas in order to maintain compliance with FCC maximum limit of +36 dBi. If other coaxial cable is used, make the appropriate changes in loss figures. NOTE: The authority to operate the transceiver in the USA may be void if antennas other than those approved by the FCC are used. Contact your factory representative for additional antenna information. Table 5-3. Feedline Length vs. Antenna Gain*

(Required for Regulatory Compliance) Antenna Gain (dBd) Antenna Gain (dBi) Minimum Feedline Loss (dB) that must be introduced for compliance EIRP Level @

Min. Feedline Length Maxrad Antenna Part No. (For 900 MHz Operation) Unity (0 dB) 2.15 dBi No minimum length

+32.15 dBm Omni #MFB900 3 dBd 5 dBd 6 dBd 9 dBd 5.15 dBi 7.15 dBi 8.15 dBi 11.15 dBi 15.2 dBd 17.4 dBi No minimum length

+35.15 dBm Omni # MFB900 1.2 dB 2.2 dB 7.15 dB 12 dB

+35.95 dBm Omni # MFB900

+35.95 dBm Yagi # BMOY8903

+35.25 dBm Yagi # Z941

+35.4 dBm Andrew DB878G90A-XY

*Refer to Table 5-4 on Page 172 for allowable transceiver power set-

tings for each antenna type. 168 Mercury Reference Manual 05-4446A01, Rev. E NOTE: There is no minimum feedline length required when a 6 dBi gain or less antenna is used, as the EIRP will never exceed 36 dBm which is the maximum allowed, per FCC rules at 900 MHz. MDS 3650 models must not exceed 1-watt per MHz. Units must comply with the information given on Page 172 and the associated antenna tables. Only the manufacturer or a sub-contracted professional installer can adjust the trans-

ceivers RF output power. The transceivers power output is factory set to maintain compliance with the FCCs Digital Transmission System

(DTS) Part 15 rules. These rules limit power to a maximum of 8 dBm/3 kHz, thus the transceiver is factory set to +29 dBm

(900 model); 23 dBm (3650 model). When calculating maximum transceiver output for the 900 model, use +29 dBm if the antenna gain is 6 dBi or less (36 dBm ERP). See How Much Output Power Can be Used? below for power control with higher gain antennas. Refer to Page 172 and the associ-

ated antenna tables for both 900 and 3650 model compliance. 5.1.5 How Much Output Power Can be Used?

The transceiver is normally configured at the factory for a nominal RF power output of +29 dBm (900 model); +23 dBm (3650 model) this is the maximum transmitter output power allowed under FCC rules. The power must be decreased from this level if the antenna system gain exceeds 6 dBi (900 model). The allowable level is dependent on the antenna gain, feedline loss, and the transmitter output power setting. NOTE: In some countries, the maximum allowable RF output might be limited to less than the figures referenced here. Be sure to check for and comply with the requirements for your area. 5.1.6 Conducting a Site Survey If you are in doubt about the suitability of the radio sites in your system, it is best to evaluate them before a permanent installation is underway. You can do this with an on-the-air test (preferred method), or indirectly, using path-study software. An on-the-air test is preferred because it allows you to see firsthand the factors involved at an installation site, and to directly observe the quality of system operation. Even if a computer path study was conducted ear-

lier, perform this test to verify the predicted results. Perform the test by first installing a radio and antenna at the proposed Access Point (AP) station site (one-per-system). Then visit the Remote site(s) with another transceiver (programmed as a remote) and a hand-held antenna. (A PC with a network adapter can be connected to 05-4446A01, Rev. E Mercury Reference Manual 169 each radio in the network to simulate data during this test, using the PING command.) With the hand-held antenna positioned near the proposed mounting spot, a technician can check for synchronization with the Access Point station (shown by a lit LINK LED on the front panel), then measure the reported RSSI value. (See Antenna Aiming (For Directional Antennas) on Page 158 for details.) If you cannot obtain adequate signal strength, it might be necessary to mount the station antennas higher, use higher gain antennas, select a different site, or install a repeater station. To prepare the equipment for an on-the-air test, follow the general installation procedures given in this guide and become familiar with the operating instructions found in the CHAPTER-2 TABLETOP EVALUATION AND TEST SETUP on Page 21. 5.1.7 A Word About Radio Interference The transceiver shares the radio-frequency spectrum with other services and users. Completely error-free communications might not be achiev-

able in a given location, and some level of interference should be expected. However, the radios flexible design and hopping techniques should allow adequate performance as long as you carefully choose the station location, configuration of radio parameters, and software/pro-

tocol techniques. In general, keep the following points in mind when setting up your com-

munications network:

Systems installed in rural areas are least likely to encounter interfer-

ence; those in suburban and urban environments are more likely to be affected by other devices operating in the license-free frequency band and by adjacent licensed services. Use a directional antenna at remote sites whenever possible. Although these antennas may be more costly than omnidirectional types, they conne the transmission and reception pattern to a com-

paratively narrow lobe, minimizing interference to (and from) sta-

tions located outside the pattern. If interference is suspected from a nearby licensed system (such as a paging transmitter), it might be helpful to use horizontal polarization of all antennas in the network. Because most other services use ver-

tical polarization in this band, you can achieve an additional 20 dB of attenuation to interference by using horizontal polarization. Another approach is to use a bandpass lter to attenuate all signals outside the desired band. Multiple Access Point units can co-exist in proximity to each other with no interference. The APs should be congured to operate in TDD Sync Mode, where their transmissions are synchronized to GPS timing. See Protected Network Operation using Multiple 170 Mercury Reference Manual 05-4446A01, Rev. E APs on Page 16. For additional isolation, separate directional antennas with as much vertical or horizontal separation as is practi-

cal. The power output of all radios in a system should be set for the low-

est level necessary for reliable communications. This reduces the chance of causing unnecessary interference to nearby systems and also keeps power consumption to a minimum. Configuring Mercury 3650 for Shared Spectrum Use

(Contention-Based Protocol) While the Mercury 3650 has been designed to reduce the effects of inter-

ferers outside of the RF channel, cases may arrive where interferers may cause undesired operation. In the case of WiMAX interferers, proper configuration of the radio may reduce these effects. The radio employs a WiMAX contention protocol that effectively reduces the amount of interference the network may cause to other co-located WiMAX networks using the same channel. In addition, proper configuration of the radio will help to reduce the effects of other WiMAX hardware attempting to do the same. Remote radios receive scheduling information from a central base sta-

tion (AP). This scheduling information destined for a given remote includes when to transmit, the duration of transmission, and modulation selection. In the event the intended Remote unit is unable to receive or interpret this information from the AP, the Remote will persist in receive mode only. The radio allows the installer to configure an Approved Access Point list that contains the MAC addresses of desired AP radios in the network. When an Access Point sends scheduling data to the Remote unit, the Remote compares the MAC Address of the AP to this approved MAC address list, and discards the scheduling information if it has originated from a foreign network. In order to maximize the performance of a shared network, the fol-

lowing configuration is recommended:

1. The Mercury 3650 network should be set to operate on the same channel frequency as the network the channel is shared with. Slight offsets in frequency between two collocated systems will cause on-channel interference that is not decodable by either system. Having both systems operate on the same frequency allows the radio to decode WiMAX scheduling information from the interfering AP. 2. Congure the approved AP list using the AP Locations le as speci-

ed in the AP Location Push Cong Menu on Page 60. After the Remote unit has received scheduling information from the interfer-

ing network, it will compare the MAC address of this radio to its AP 05-4446A01, Rev. E Mercury Reference Manual 171 Locations File. When the MAC address does not match, the radio will ignore this information from the interfering AP and continue to wait for valid scheduling information from an AP in the desired net-

work. 5.1.8 EIRP Compliance at 900 MHz To determine the maximum allowable power setting of the radio, per-

form the following steps:

1. Determine the antenna system gain by subtracting the feedline loss

(in dB) from the antenna gain (in dBi). For example, if the antenna gain is 9.5 dBi, and the feedline loss is 1.5 dB, the antenna system gain would be 8 dB. (If the antenna system gain is 6 dB or less, no power adjustment is required.) 2. Subtract the antenna system gain from 36 dBm (the maximum allowable EIRP). The result indicates the maximum transmitter power (in dBm) allowed under the rules. In the example above, this is 28 dBm. 3. Set the transmitter power so that it does not exceed the maximum level determined in Step 2.

(Main Menu>>Radio Configuration>>Transmit Power) Refer to Table 5-4, which lists several antenna system gains and shows the maximum allowable power setting of the radio. Note that a gain of 6 dB or less entitles you to operate the radio at full power output 30 dBm. For MDS 3650 units, refer also to the section titled EIRP Compliance at 3650 MHz below. Table 5-4. Antenna Gain vs. Power Setpoint (900 MHz) Antenna System Gain

(Antenna Gain in dBi*

minus Feedline Loss in dB) Maximum Power Setting

(PWR command) EIRP

(in dBm) Omni 6 (or less) Omni 11 Yagi 11 Half Parabolic 16 Panel 17.4**

29 25 23 20 20 35 36 36 36 36

* Most antenna manufacturers rate antenna gain in dBd in their litera-

ture. To convert to dBi, add 2.15 dB.

** Must use with the appropriate length of feedline cable to reduce transmitter power by at least 2 dB. Feedline loss varies by cable type and length. To determine the loss for common lengths of feed-

line, see Table 5-1 on Page 167. 172 Mercury Reference Manual 05-4446A01, Rev. E 5.1.9 EIRP Compliance at 3650 MHz To maintain regulatory compliance for Effective Isotropic Radiated Power (EIRP) of 1-Watt per MHz, the following table of transmit power settings must be observed for the listed bandwidths and antenna types approved. Consult the factory for other antenna options of lower gain. Table 5-5. Antenna Gain vs. Power Setpoint (3650 MHz) Antenna Gain

(dBi) 13 13 13 13 13 13 18 18 18 18 18 18 Radio Configuration

(Antenna Type/Radio Bandwidth)) Omni Antenna, 1.75 MHz BW Omni Antenna, 3.5 MHz BW Omni Antenna, 5 MHz BW Omni Antenna, 7 MHz BW Omni Antenna, 10 MHz BW Omni Antenna, 14 MHz BW Panel Antenna, 1.75 MHz BW Panel Antenna, 3.5 MHz BW Panel Antenna, 5 MHz BW Panel Antenna, 7 MHz BW Panel Antenna, 10 MHz BW Panel Antenna, 14 MHz BW Radio Power Setpoint

(dBm) 22 23 23 23 23 23 17 20 22 23 23 23 The antennas used to support operation in this band must be fixed mounted. 05-4446A01, Rev. E Mercury Reference Manual 173 5.2 dBm-WATTS-VOLTS CONVERSION CHART Table 5-6 is provided as a convenience for determining the equivalent voltage or wattage of an RF power expressed in dBm. Table 5-6. dBm-Watts-Volts conversionfor 50 ohm systems Po dBm V

+53

+50

+49

+48

+47

+46

+45

+44

+43

+42

+41

+40

+39

+38

+37

+36

+35

+34

+33

+32

+31

+30

+29

+28

+27

+26

+25

+24

+23

+22

+21

+20

+19

+18

+17

+16

+15

+14

+13

+12

+11

+10

+9

+8

+7

+6

+5

+4

+3

+2

+1 100.0 200W 100W 70.7 80W 64.0 64W 58.0 50W 50.0 44.5 40W 32W 40.0 25W 32.5 20W 32.0 16W 28.0 12.5W 26.2 10W 22.5 20.0 8W 6.4W 18.0 5W 16.0 4W 14.1 3.2W 12.5 2.5W 11.5 10.0 2W 1.6W 9.0 1.25W 8.0 1.0W 7.10 800mW 6.40 640mW 5.80 5.00 500mW 400mW 4.45 320mW 4.00 250mW 3.55 200mW 3.20 160mW 2.80 2.52 125mW 100mW 2.25 80mW 2.00 64mW 1.80 50mW 1.60 40mW 1.41 32mW 1.25 1.15 25mW 20mW 1.00 16mW

.90 12.5mW

.80 10mW

.71 8mW

.64

.58 6.4mW 5mW

.500 4mW

.445 3.2mW

.400 2.5mW

.355 2.0mW

.320

.280 1.6mW 1.25mW

.252 Po 1.0mW

.80mW

.64mW

.50mW

.40mW

.32mW

.25mW

.20mW

.16mW

.125mW

.10mW dBm V 0

-1

-2

-3

-4

-5

-6

-7

-8

-9

-10

-11

-12

-13

-14

-15

-16

.225

.200

.180

.160

.141

.125

.115

.100

.090

.080

.071

.064

.058

.050

.045

.040

.0355

.001mW

.01mW dBm mV Po

-17

-18

-19

-20

-21

-22

-23

-24

-25

-26

-27

-28

-29

-30

-31

-32

-33

-34

-35

-36

-37

-38

-39

-40

-41

-42

-43

-44

-45

-46

-47

-48 31.5 28.5 25.1 22.5 20.0 17.9 15.9 14.1 12.8 11.5 10.0 8.9 8.0 7.1 6.25 5.8 5.0 4.5 4.0 3.5 3.2 2.85 2.5 2.25 2.0 1.8 1.6 1.4 1.25 1.18 1.00 0.90

.1W dBm V 2.9

-98 2.51

-99 2.25

-100 2.0

-101 1.8

-102

-103 1.6 1.41

-104 1.27

-105

-106 1.18 dBm nV

-107 1000 900

-108 800

-109 710

-110 640

-111 580

-112 500

-113

-114 450 400

-115 355

-116 325

-117 285

-118 251

-119

-120 225 200

-121 180

-122 160

-123 141

-124 128

-125

-126 117 100

-127 90

-128 80

-129 71

-130 61

-131

-132 58 50

-133 45

-134 40

-135 35

-136 33

-137 29

-138

-139 25 23

-140 Po

.1pW Po

.01pW

.001pW

.1W

.01W

.01W dBm mV Po

-49

-50

-51

-52

-53

-54

-55

-56

-57

-58

-59

-60

-61

-62

-63

-64 0.80 0.71 0.64 0.57 0.50 0.45 0.40 0.351 0.32 0.286 0.251 0.225 .001W 0.200 0.180 0.160 0.141 Po

.1nW

.01nW

.001nW dBm V

-65 128 115

-66 100

-67 90

-68 80

-69 71

-70

-71 65 58

-72 50

-73 45

-74 40

-75 35

-76

-77 32 29

-78 25

-79 22.5

-80 20.0

-81 18.0

-82

-83 16.0 11.1

-84 12.9

-85 11.5

-86 10.0

-87 9.0

-88 8.0

-89

-90 7.1 6.1

-91 5.75

-92 5.0

-93 4.5

-94 4.0

-95

-96 3.51 3.2

-97 174 Mercury Reference Manual 05-4446A01, Rev. E 6 TECHNICAL REFERENCE 6 Chapter Counter Reset Paragraph Contents 6.1 DATA INTERFACE CONNECTORS ........................................177 6.1.1 LAN Port ...................................................................................177 6.1.2 COM1 Port ...............................................................................177 6.2 SPECIFICATIONS...................................................................178 6.3 NOTES ON SNMP...................................................................180 6.3.1 Overview ..................................................................................180 05-4446A01, Rev. E Mercury Reference Manual 175 176 Mercury Reference Manual 05-4446A01, Rev. E CAUTION RADIO FREQUENCY INTERFERENCE POTENTIAL 6.1 DATA INTERFACE CONNECTORS Two types of data interface connectors are provided on the front panel of the transceiveran RJ-45 LAN port, and a DB-9 serial port (COM1), which uses the RS-232 (EIA-232) signaling standard. The transceiver meets U.S.A.s FCC Part 15, Class A limits when used with shielded data cables. 6.1.1 LAN Port Use the transceivers LAN port to connect the radio to an Ethernet net-

work. The transceiver provides a data link to an Internet Protocol-based

(IP) network via the Access Point station. Each radio in the network must have a unique IP address for the network to function properly. To connect a PC directly to the radios LAN port, an RJ-45 to RJ-45 cross-over cable is required. To connect the radio to a Ethernet hub or bridge, use a straight-through cable. The connector uses the standard Ethernet RJ-45 cables and wiring. For custom-made cables, use the pinout information in Figure 6-1 and Table 6-1. 1 2 3 4 5 6 7 8 Figure 6-1. LAN Port (RJ-45) Pinout

(Viewed from the outside of the unit) Table 6-1. LAN Port (IP/Ethernet) Pin 1 2 3 4 5 6 7 8 Functions Transmit Data (TX) Transmit Data (TX) Receive Data (RX) Unused Unused Receive Data (RX) Unused Unused Ref. High Low High Low 6.1.2 COM1 Port The COM1 serial port is a standard DB-9 female connector. Connect a PC to the transceiver via this port with a DB-9M to DB-9F 05-4446A01, Rev. E Mercury Reference Manual 177 straight-through cable. These cables are available commercially, or may be constructed using the pinout information in Table 6-2. Table 6-2. COM1 Port Pinout, DB-9F/RS-232 Interface Pin 1 Functions Unused DCE 2 3 4 5 Receive Data (RXD) Transmit Data (TXD) >[In

<[Out Unused Signal Ground (GND) 69 Unused 6.2 SPECIFICATIONS General Raw Bit Rate: from 600 kbps to 12.7 Mbps Frequency Bands: 902-928 MHz ISM band 3.65-3.7 GHz Registered FCC band Bandwidths: 900 model1.75, 3.5 MHz 3650 model1.75, 3.5, 5, 7 MHz Orthogonal Frequency Division Multiplexing (OFDM) 200 Carriers per Channel Available Configurations:

Access Point: Ethernet, Serial, GPS Remote: Ethernet, Serial, GPS Radio System Gain: 140 dB for 1.75 MHz channel, 137 dB for 3.5 MHz channel Carrier PowerAP: -30 to +29 dBm, RM: 0 to +29 dBm (900 models); +23 dBm max. (3650 model) RF Output Impedance: 50 Ohms Sensitivity and Signal Rate (see Table 6-3):

Table 6-3. Sensitivity and Signal Rate 178 Mercury Reference Manual 05-4446A01, Rev. E Note that the transceiver is a half-duplex radio, so maximum user throughput is based on a configured or dynamic duty cycle, which is typ-

ically 50/50 indicating that half of the maximum throughput would be available one way. The maximum user throughput is also based on high protocol overhead from TCP/IP applications. For UDP applications, these throughput numbers will increase. Physical Interface Ethernet: 10/100BaseT, RJ-45 Serial: 1,200 115,200 bps COM1: RS-232, DB-9F Antennas: TX/RXTNC connector, GPSSMA connector LED Indicators: PWR, COM1, LINK, LAN Protocols (Pendingcontact factory for details) Ethernet: IEEE 802.3, Spanning Tree (Bridging), VLAN, IGMP TCP/IP: DHCP, ICMP, UDP, TCP, ARP, Multicast, SNTP, TFTP Serial: Encapsulation over IP (tunneling) for serial async multi-

drop protocols including MODBUS, DNP.3, DF1, BSAP GE MDS Cyber Security Suite, Level 1 Encryption: AES-128. Authentication: 802.1x, RADIUS, EAP/TLS, PKI, PAP, CHAP Management: SSL, SSH, HTTPS Management HTTP, HTTPS, TELNET, SSH, local console SNMPv1/v2/v3, MIB-II, Enterprise MIB SYSLOG MDS NETview MS compatible Environmental Temperature: -40C to +70C (-40F to +158F) Humidity: 95% at 40C (104F) non-condensing Electrical Input Power: 10-30 Vdc Current Consumption (nominal):

Mode AP Transmit AP Receive RM Transmit RM Receive Power 25 W 8 W 25W 6.5W 13.8 Vdc 1.8 A 579 mA 1.8 mA 471 mA 24 Vdc 1.0 A 333 mA 1.0 A 270 mA 05-4446A01, Rev. E Mercury Reference Manual 179 Mechanical Case: Die Cast Aluminum Dimensions: 5.715 H x 20 W x 12.382 D cm. (2.25 H x 7.875 W x 4.875 D in.) Weight: 1kg (2.2 lb.) Mounting options: Flat surface mount brackets, DIN rail, 19 rack tray External GPS PPS Option Parameter Minimum Maximum Pulse Voltage (logic low) Pulse Voltage (logic high) Source Impedance (ohms) Duty Cycle (ton) Operating Frequency Module Clamping Voltage Module Input Resistance Input Hysteresis Agency Approvals 0 V 1.7 V 1 V 10 V 200 0.0001% (1sec) 0.99999999 Hz

(-0.1 ppm error) 2.7 V 50% (0.5 sec) 1.00000001 Hz

(+0.1 ppm error) 3.3 V 150 (Vin >2.6 V) 10 k (Vin < 2 V) 7 mV N/A FCC Part 15.247 (DTS)900 model FCC Part 903650 model CSA Class 1 Div. 2, (CSA C22.2-213-M1987 & CSA C22.2-142-M1987) (UL1604 & UL916) IC RSS-210 Issue 7 NOTE: GE MDS products are manufactured under a quality system certified to ISO 9001. GE MDS reserves the right to make changes to specifications of products described in this manual at any time without notice and without obligation to notify any person of such changes. 6.3 NOTES ON SNMP 6.3.1 Overview The firmware release described in this manual contains changes to the transceivers SNMP Agent, several new MIB variables, and new Agent configuration options. This guide reviews the changes and shows how to properly configure the Agent to take advantage of these new features. SNMPv3 Support The updated SNMP Agent now supports SNMP version 3 (SNMPv3). The SNMPv3 protocol introduces Authentication (MD5/SHA-1), 180 Mercury Reference Manual 05-4446A01, Rev. E Encryption (DES), the USM User Table, and View-Based Access (refer to RFC2574 for full details). The SNMP Agent has limited SNMPv3 support in the following areas:

Only MD5 Authentication is supported (no SHA-1). SNMPv3 provides support for MD5 and SHA-1. Limited USM User Table Manipulation. The SNMP Agent starts with 5 default accounts. New accounts can be added

(SNMPv3 adds new accounts by cloning existing ones), but they will be volatile (will not survive a power-cycle). New views cannot be configured on the SNMP Agent. Views are inherited for new accounts from the account that was cloned. The SNMP Agent uses one password pair (Authentication/Pri-

vacy) for all accounts. This means that when the passwords change for one user, they change for all users. SNMPv3 Accounts The following default accounts are available for the SNMP Agent:

enc_mdsadminRead/write account using Authentication and Encryp-

tion. auth_mdsadminRead/write account using Authentication. enc_mdsviewerRead only account using Authentication and Encryp-

tion. auth_mdsviewerRead only account using Authentication. def_mdsviewerRead only account with no Authentication or Encryp-

tion. Context Names The following Context Names are used (refer to RFC2574 for full details):

Admin accounts: context_a/Viewer accounts: context_v. All accounts share the same default passwords:

Authentication default password: MDSAuthPwd/Privacy default pass-

word: MDSPrivPwd. Passwords can be changed either locally (via the console) or from an SNMP Manager, depending on how the Agent is configured. If pass-

words are configured and managed locally, they are non-volatile and will survive a power-cycle. If passwords are configured from an SNMP manager, they will be reset to whatever has been stored for local man-

agement on power-cycle. 05-4446A01, Rev. E Mercury Reference Manual 181 This behavior was chosen based on RFC specifications. The SNMP Manager and Agent do not exchange passwords, but actually exchange keys based on passwords. If the Manager changes the Agents password, the Agent does not know the new password. The Agent only knows the new key. In this case, only the Manager knows the new password. This could cause problems if the Manager loses the password. If that hap-

pens, the Agent becomes unmanageable. Resetting the Agents pass-

words (and therefore keys) to what is stored in flash memory upon power-cycle prevents the serious problem of losing the Agents pass-

words. If passwords are managed locally, they can be changed on the Agent (via the console). Any attempts to change the passwords for the Agent via an SNMP Manager will fail when the Agent is in this mode. Locally defined passwords will survive a power-cycle. In either case, the SNMP Manager needs to know the initial passwords being used in order to talk to the Agent. If the Agents passwords are configured via the Manager, they can be changed from the Manager. If the passwords are managed locally, then the Manager must be re-con-

figured with any password changes in order to continue talking to the Agent. Password-Mode Management Changes When the password management mode is changed, the active passwords used by the Agent may also change. Some common scenarios are dis-

cussed below:

Passwords are currently being handled by the Manager. The assigned passwords are Microwave (Auth), and Rochester (Priv). Configuration is changed to manage the passwords locally. The passwords stored on the radio were Fairport (Auth), and Churchville (Priv) (if local passwords have never been used, then MDSAuthPwd and MDSPrivPwd are used). These pass-

words will now be used by the Agent to re-generate keys. The Manager must know these passwords to talk to the Agent. Passwords are currently managed locally. The local passwords are Fairport (Auth) and Churchville (Priv). Configuration is changed to handle the passwords from the Manager. The same passwords will continue to be used, but now the Manager can change them. Passwords are currently managed locally. The local passwords are Fairport (Auth) and Churchville (Priv). Passwords are changed to Brighton (Auth) and Perinton (Priv). The Agent will immedi-

ately generate new keys based on these passwords and start using them. The Manager will have to be re-configured to use these new passwords. Common Scenarios 182 Mercury Reference Manual 05-4446A01, Rev. E Passwords are currently managed locally. The local passwords are Fairport (Auth) and Churchville (Priv). Configuration is changed to handle the passwords from the Manager. The Man-

ager changes the passwords to Brighton (Auth) and Perinton

(Priv). The radio is then rebooted. After a power-cycle, the radio will use the passwords stored in flash memory, which are Fair-

port (Auth) and Churchville (Priv). The Manager must be re-con-

figured to use these new passwords. Table 6-4. SNMP Traps (Sorted by Code) Severity CRITICAL Description System Bootup MAJOR User Selected Reboot INFORM Reprogramming Started INFORM Reprogramming Completed MAJOR MAJOR MAJOR INFORM INFORM INFORM MINOR INFORM INFORM INFORM MAJOR MAJOR INFORM INFORM MAJOR MAJOR Reprogramming Failed Telnet/SSH User login/logout HTTP User login/logout Event Log Cleared DHCP server enabled/disabled DHCP client enabled/disabled Obtained DHCP address Date/time not set Date/time changed by user Date/time from server Console user login/logout HTTP Access locked down Parameter changed Configuration script generated/received Authorization key entered - valid/invalid Demo authorization enabled/expired CRITICAL Max demos reset/reached MAJOR MAJOR MAJOR INFORM INFORM INFORM MAJOR Modem restarted Internal error GPS Restarted Remote associated/disassociated Firmware image copy started Firmware image copy complete Firmware image copy failed INFORM Connection status change MAJOR Connection aborted INFORM Authenticating to Access Point SNMP Trap bootup(34) reboot(35) reprogStarted(36) reprogCompleted(37) reprogFailed(38) telnetLogin(39) httpLogin(40) logClear(41) dhcpServer(42) dhcpClient(43) dhcpAddr(44) timeNotSet(45) timeByUser(46) timeFromServer(47) consoleLogin(48) httpLockdown(49) parmChanged(50) cfgscript(51) authKey(52) authDemo(53) maxDemos(54) modemRestart(55) internalError(56) gpsRestarted(57) remoteConnection(58) imageCopyStarted(59) imageCopyComplete(60) imageCopyFailed(61) connectionStatus(64) connAbort(65) authenticating(66) 05-4446A01, Rev. E Mercury Reference Manual 183 Table 6-4. SNMP Traps (Sorted by Code) (Continued) SNMP Trap association(67) redundLackRem(72) redundRecvErr(73) redundForced(74) redundancySwitch(75) radioError(76) procopen(77) procformat(78) csropen(79) csrstatus(80) csrctrlsignal(81) bandwidthMismatch(83) gpsSync(84) gpsTddSync(85) tftpClientConn(86) tftpClientError(87) autoUpgrade(88) autoReboot(89) certVerify(90) certChainVerify(91) paTemp(92) Severity MAJOR MAJOR MAJOR MAJOR MAJOR Description Associated to Access Point established/lost Lack of associated remotes exceeded threshold for P21 AP Packet receive errors exceeded threshold for P21 AP P21 AP forced switchover P21 AP auto switchover CRITICAL Radio error MAJOR MAJOR MAJOR MAJOR MAJOR INFORM INFORM INFORM INFORM MAJOR MAJOR MAJOR Proc filesystem access failed Unexpected proc filesystem format Failed to open CSR device CSR read failed CSR write failed Bandwidth of AP in Locations file does not match this unit GPS synchronized/lost sync TDD synchronized/lost sync TFTP Connection to Client Opened/Closed Error in TFTP Transfer to Client Auto Firmware Upgrade Retry Scheduled/Starting Auto Firmware Boot Failed/Starting CRITICAL X.509 certificates loaded/failed CRITICAL Certificate chain verified/invalid MAJOR PowerAmp temperature Normal/Too hot 184 Mercury Reference Manual 05-4446A01, Rev. E 7 GLOSSARY OF TERMS AND ABBREVIATIONS 7 Chapter Counter Reset Paragraph If you are new to wireless IP/Ethernet systems, some of the terms used in this manual might be unfamiliar. The following glossary explains many of these terms and will prove helpful in understanding the opera-

tion of your radio network. Some of these terms do not appear in the manual, but are often encountered in the wireless industry, and are there-

fore provided for completeness. Access Point (AP)The transceiver in the network that provides syn-

chronization information to one or more associated Remote units. See Network Conguration Menu on Page 45. AGCAutomatic Gain Control Antenna System GainA figure, normally expressed in dB, repre-

senting the power increase resulting from the use of a gain-type antenna. System losses (from the feedline and coaxial connectors, for example) are subtracted from this figure to calculate the total antenna system gain. APSee Access Point AssociationCondition in which the frequency hopping pattern of the Remote is synchronized with the Access Point station, and the Remote is ready to pass traffic. Authorization KeyAlphanumeric string (code) that is used to enable additional capabilities in the transceiver. BitThe smallest unit of digital data, often represented by a one or a zero. Eight bits usually comprise a byte. Bits-per-secondSee BPS. BPDUBridge Protocol Data Units BPSBits-per-second (bps). A measure of the information transfer rate of digital data across a communication channel. ByteA string of digital data made up of eight data bits. CSMA/CACarrier Sense Multiple Access/Collision Avoidance CSMA/CDCarrier Sense Multiple Access/Collision Detection Cyclic Redundancy Check (CRC)A technique used to verify data integrity. It is based on an algorithm which generates a value derived 05-4446A01, Rev. E Mercury Reference Manual 185 from the number and order of bits in a data string. This value is com-

pared with a locally-generated value and a match indicates that the mes-

sage is unchanged, and therefore valid. Data Circuit-terminating EquipmentSee DCE. Data Communications EquipmentSee DCE. DatagramA data string consisting of an IP header and the IP message within. Data Terminal EquipmentSee DTE. dBdDecibels (dipole antenna). dBiDecibels referenced to an ideal isotropic radiator in free space. Frequently used to express antenna gain. dBmDecibels referenced to one milliwatt. An absolute unit used to measure signal power, as in transmitter power output, or received signal strength. DCEData Circuit-terminating Equipment (or Data Communications Equipment). In data communications terminology, this is the modem side of a computer-to-modem connection. COM1 Port of the transceiver is set as DCE. Decibel (dB)A measure of the ratio between two signal levels. Fre-

quently used to express the gain (or loss) of a system. DelimiterA flag that marks the beginning and end of a data packet. Device ModeThe operating mode/role of a transceiver (Access Point or Remote) in a wireless network. DHCP (Dynamic Host Configuration Protocol)An Internet stan-

dard that allows a client (i.e. any computer or network device) to obtain an IP address from a server on the network. This allows network admin-

istrators to avoid the tedious process of manually configuring and man-

aging IP addresses for a large number of users and devices. When a network device powers on, if it is configured to use DHCP, it will con-

tact a DHCP server on the network and request an IP address. The DHCP server will provide an address from a pool of addresses allo-

cated by the network administrator. The network device may use this address on a time lease basis or indefinitely depending on the policy set by the network administrator. The DHCP server can restrict alloca-

tion of IP addresses based on security policies. An Access Point may be configured by the system administrator to act as a DHCP server if one is not available on the wired network. 186 Mercury Reference Manual 05-4446A01, Rev. E Digital Signal ProcessingSee DSP. DSPDigital Signal Processing. DSP circuitry is responsible for the most critical real-time tasks; primarily modulation, demodulation, and servicing of the data port. DTEData Terminal Equipment. A device that provides data in the form of digital signals at its output. Connects to the DCE device. EncapsulationProcess in by which, a complete data packet, such as MODBUS frame or any other polled asynchronous protocol frame, is placed in the data portion of another protocol frame (in this case IP) to be transported over a network. Typically this action is done at the trans-

mitting end, before being sent as an IP packet to a network. A similar reversed process is applied at the other end of the network extracting the data from the IP envelope, resulting in the original packet in the original protocol. EndpointData equipment connected to the Ethernet port of the radio. EqualizationThe process of reducing the effects of amplitude, fre-

quency or phase distortion with compensating networks. Fade MarginThe greatest tolerable reduction in average received signal strength that will be anticipated under most conditions. Provides an allowance for reduced signal strength due to multipath, slight antenna movement or changing atmospheric losses. A fade margin of 15 to 20 dB is usually sufficient in most systems. FragmentationA technique used for breaking a large message down into smaller parts so it can be accommodated by a less capable media. FrameA segment of data that adheres to a specific data protocol and contains definite start and end points. It provides a method of synchro-

nizing transmissions. Frequency HoppingThe spread spectrum technique used by the transceiver, where two or more associated radios change their operating frequencies many times per second using a set pattern. Since the pattern appears to jump around, it is said to hop from one frequency to another. GPSGlobal Positioning System. A constellation of orbiting satellites used for navigation and timing data. Although 24 satellites are normally active, a number of spares are also available in case of malfunction. Originally designed for military applications by the U.S. Department of Defense, GPS was released for civilian use in the 1980s. GPS satellites operate in the vicinity of the L frequency band (1500 MHz). Hardware Flow ControlA transceiver feature used to prevent data buffer overruns when handling high-speed data from the connected data 05-4446A01, Rev. E Mercury Reference Manual 187 communications device. When the buffer approaches overflow, the radio drops the clear-to-send (CTS) line, that instructs the connected device to delay further transmission until CTS again returns to the high state. Host ComputerThe computer installed at the master station site, that controls the collection of data from one or more remote sites. HTTPHypertext Transfer Protocol ICMPInternet Control Message Protocol IGMP (Internet Gateway Management Protocol)Ethernet level protocol used by routers and similar devices to manage the distribution of multicast addresses in a network. IEEEInstitute of Electrical and Electronic Engineers IEEE 802.1QA standard for Ethernet framing which adds a four-byte tag after the Ethernet header. The four-byte tag contains a VLAN ID and a IEEE 802.1P priority value. IEEE 802.1XA standard for performing authentication and port blocking. The 802.1X port/device denies access to the network until the client device has authenticated itself. Image (File)Data file that contains the operating system and other essential resources for the basic operation of the radios CPU. LANLocal Area Network LatencyThe delay (usually expressed in milliseconds) between when data is applied at the transmit port at one radio, until it appears at the receive port at the other radio. MACMedia Access Controller MD5A highly secure data encoding scheme. MD5 is a one-way hash algorithm that takes any length of data and produces a 128 bit finger-

print. This fingerprint is non-reversible, it is computationally infea-

sible to determine the file based on the fingerprint. For more details review RFC 1321 available on the Internet. MIBManagement Information Base Microcontroller UnitSee MCU. MobilityRefers to a station that moves about while maintaining active connections with the network. Mobility generally implies phys-

ical motion. The movement of the station is not limited to a specific net-

work and IP subnet. In order for a station to be mobile it must establish 188 Mercury Reference Manual 05-4446A01, Rev. E and tear down connections with various access points as it moves through the access points' territory. ModeSee Device Mode. MTBFMean-Time Between Failures Multiple Address System (MAS)See Point-Multipoint System. NMEANational Marine Electronics Association. National body that established a protocol for interfacing GPS data between electronic equipment. Network NameUser-selectable alphanumeric string that is used to identify a group of radio units that form a communications network. The Access Point and all Remotes within a given system should have the same network address. Network-Wide DiagnosticsAn advanced method of controlling and interrogating GE MDS radios in a radio network. NTPNetwork Time Protocol PacketThe basic unit of data carried on a link layer. On an IP network, this refers to an entire IP datagram or a fragment thereof. PINGPacket INternet Groper. Diagnostic message generally used to test reachability of a network device, either over a wired or wireless net-

work. PKIPrivate Key Infrastructure. A set of policies and technologies needed to create, store, and distribute Public Key Certificates used to protect the security of network communications. Point-to-Multipoint SystemA radio communications network or system designed with a central control station that exchanges data with a number of remote locations equipped with terminal equipment. PollA request for data issued from the host computer (or master PLC) to a remote device. PortabilityA station is considered connected when it has successfully authenticated and associated with an access point. A station is consid-

ered authenticated when it has agreed with the access point on the type of encryption that will be used for data packets traveling between them. The process of association causes a station to be bound to an access point and allows it to receive and transmit packets to and from the access point. In order for a station to be associated it must first authenticate with the access point. The authentication and association processes occur automatically without user intervention. 05-4446A01, Rev. E Mercury Reference Manual 189 Portability refers to the ability of a station to connect to an access point from multiple locations without the need to reconfigure the network set-

tings. For example, a remote transceiver that is connected to an access point may be turned off, moved to new site, turned back on, and, assuming the right information is entered, can immediately reconnect to the access point without user intervention. PLCProgrammable Logic Controller. A dedicated microprocessor configured for a specific application with discrete inputs and outputs. It can serve as a host or as an RTU. PuTTYA free implementation of Telnet and SSH for Win32 and Unix platforms. It is written and maintained primarily by Simon Tatham. Refer to http://www.pobox.com/~anakin/ for more information. RADIUSRemote Authentication Dial In User Service. An authenti-

cation, authorization, and accounting protocol used to secure remote access to a device or network. RemoteA transceiver in a network that communicates with an asso-

ciated Access Point. Remote Terminal UnitSee RTU. RFIRadio Frequency Interference RoamingA station's ability to automatically switch its wireless con-

nection between various access points (APs) as the need arises. A station may roam from one AP to another because the signal strength or quality of the current AP has degraded below what another AP can provide. Roaming may also be employed in conjunction with Portability where the station has been moved beyond the range of the original AP to which it was connected. As the station comes in range of a new AP, it will switch its connection to the stronger signal. Roaming refers to a station's logical, not necessarily physical, move between access points within a specific network and IP subnet. RSSIReceived Signal Strength Indicator RTURemote Terminal Unit. A data collection device installed at a remote radio site. SCADASupervisory Control And Data Acquisition. An overall term for the functions commonly provided through an MAS radio system. SNMPSimple Network Management Protocol SNRSignal-to-Noise Ratio. A measurement of the desired signal to ambient noise levels.This measurement provides a relative indication of signal quality. Because this is a relative number, higher signal-to-noise ratios indicate improved performance. 190 Mercury Reference Manual 05-4446A01, Rev. E SNTPSimple Network Time Protocol SSLSecure Socket Layer SSHSecure Shell STPSpanning Tree Protocol Standing-Wave RatioSee SWR. SWRStanding-Wave Ratio. A parameter related to the ratio between forward transmitter power and the reflected power from the antenna system. As a general guideline, reflected power should not exceed 10%

of the forward power ( 2:1 SWR). TCPTransmission Control Protocol TFTPTrivial File Transfer Protocol Trap ManagerSoftware that collects SNMP traps for display or log-

ging of events. UDPUser Datagram Protocol UTPUnshielded Twisted Pair VLANVirtual Local Area Network. A network configuration employing IEEE 802.1Q tagging, which allows multiple groups of devices to share the same physical medium while on separate broadcast domains. 05-4446A01, Rev. E Mercury Reference Manual 191 192 Mercury Reference Manual 05-4446A01, Rev. E INDEX Numerics 100BaseT 56, 163 10BaseT 56, 163 16QAM 75 64QAM 75 802.11b 12 A Access Point (AP), defined 185 accessories 19 Active Scanning, defined 185 adapter TNC Male-to-N Female 19 Adaptive Modulation 73 Split 74 Add Associated Remotes 97 Remote 97 Address to Ping 135 Advanced Configuration 66 Control 71 AES encryption 4 agency approvals 180 alarm conditions 154 correcting 155 Alarmed 152 alarms 153 Altitude 116 antenna 900 MHz 5 aiming 158 cross-polarization 15 directional 5, 170 for repeater stations 15 GPS 5, 167 receiving 19 minimizing interference 15 Minimum Feedline Length versus Antenna Gain 168 omni-directional 5, 14, 19, 166 polarization 166 selection 165 SWR check 157 system gain defined 185 vs. power output setting 172 vertical separation 15 Yagi 14, 19, 166 AP current name 144 Location Info Config 46 locations 6064 application IP-to-Serial 83 Mixed-Modes 87 Point-to-Multipoint Serial-to-Serial 84 Point-to-Point Serial-to-Serial 83 Serial Port 87 approvals agency 180 Approved Remotes 96 ARQ 74 Block Lifetime 74 Block Size 74 Receiver Delay 74 Transmitter Delay 74 Window Size 74 Associated 152 Remotes 43, 118 association defined 185 process 117 attenuation 24 Auth Server Address 99 Port 99 Shared Secret 99 Auth Traps Status 60 Authenticating 152 authentication device 97 user 98 Authorization Codes 124, 136 Key 136 defined 185 Authorized Features 136 Auto Firmware Upgrade 125 Automatic Repeat Request 74 Auto-Upgrade/Remote-Reboot 138 Average RSSI 122 SNR 122 B Backhaul for serial radio networks 11 Network 11 bandpass filter 170 baud rate 79, 82 console 76 serial data 76 Begin Wizard 78 Bit, defined 185 Bits-per-second (bps), defined 185 BPDU 58 defined 185 BPS, defined 185 BPSK 75 Bridge Configuration 46 Forward Delay 58 Hello Time 58 Priority 58 Protocol Data Unit 58 Bridge Status 111 Buffer Size 79, 81, 82 BW 63 Byte Format 79 byte format 80, 82 bytes defined 185 received 115 sent 115 05-4446A01, Rev. E Mercury Reference Manual I-1 C cable crossover 36, 38, 177 EIA-232 Shielded Data 19 Ethernet crossover 14, 25, 39 Ethernet RJ-45 Crossover 19 Ethernet RJ-45 Straight-thru 19 feedlines 167 serial communications 25, 37 straight-through 38, 39, 177 certificate files 97 type 101 Certificate Filename 101 Change Admin Password 95 Guest Password 95 channel selection 71 single frequency 70 type 74 CHANNELS 63 clear Ethernet statistics 115 Event Log 113 MDS wireless statistics 115 Collocating Multiple Radio Networks 16 Commit Changes and Exit Wizard 80, 81, 82 communication peer-to-peer 10 Compression 145 Computer host, defined 188 Config filename 133 configuration 25, 81 advanced 66 defaults 25 DHCP server 50 editing files 134 Ethernet Port 56 file 25, 149 IP address 53 network 45 P23 8 protected network 8 radio parameters 6588 RADIUS 99 redundant 8 script 124, 131 SNMP Agent 58 TCP Mode 81 UDP mode 79 Connecting 152 Connection Status 43, 119, 121, 143 connectionware 145 connector descriptions 177 Ethernet 10 console baud rate 76, 109 Contact 110 context names 181 Corrected FEC Count 123, 144 cost of deployment 12 Count 135 CRC (Cyclic Redundancy Check), defined 185 CSMA CA, defined 185 CD, defined 185 Current Alarms 113 Current AP 70 Eth Address 119 IP Address 119 Name 119, 121, 144 Current IP Address 42, 50, 53 Gateway 50, 53 Netmask 50, 53 Cyclic Prefix 74 D data baud rate 81 buffering 77 compression 73 encryption 96 VLAN ID 49 VLAN Subnet Config 49 Datagram, defined 186 Date 109 Format 109 dB, defined 186 dBd, defined 186 dBi, defined 186 dBm defined 186 watts-volts conversion 174 DCE, defined 186 Default Route IF 49 defaults resetting 137 Delete All Remotes 97 Remote 97 Delimiter, defined 186 deployment costs 12 Description 110 Device Auth Mode 96 Authentication 97 Information 45 Menu 109 Mode 42 defined 186 Name 42, 110, 135 Security Menu 93 Status 42, 118, 152 messages 152 DHCP 53 defined 186 DNS address 52 ending address 52 Netmask 52 Server 49 Config 49 Configuration 46, 47 Status 52 starting address 52 WINS address 52 Diagnostic Tools 153 dimensions 163 I-2 Mercury Reference Manual 05-4446A01, Rev. E DIN Rail Mounting Bracket 20 DKEY command 157 Downlink 144 Percentage 74 DSP (Digital Signal Processing), defined 187 DTE defined 187 DUR 63 E EIA-232 13 Embedded Management System 25 Enable Filtering 57 encapsulation defined 187 serial 76 transparent 76 encryption 5 AES 4 Phrase 96 Endpoint defined 187 Equalization, defined 187 Ethernet filtering configuration 57 Port Config 46 port enable 56 port follows association 57 port phy rate 56 event Alarms 154 Critical 154 Informational 154 Major 154 Minor 154 Temporary Informational 154 Event Log 111, 114, 152, 153, 154, 155 clear 113 filename 113 host address 113 Menu 113 send 113 view 113 events 153 F factory defaults resetting 137 Fade Margin 187 FEC 73 count corrected 123, 144 total 123, 144 uncorrected 123, 144 Total 144 feedline selection 165, 167 file certificate 97 MIB 33 Filename 127 filtering enable 57 firmware automatic upgrade 125 current 128 filename 130 for Upgrade 138 installing 129 upgrade 130, 138 version 43, 125 Flow Control hardware, defined 187 Force Switchover 103 Fragmentation defined 187 frame defined 187 duration 70 Free Run 24, 27, 29 frequency control 66 hopping, defined 187 mode 26, 68 offset RX 144 TX 144 fuse 19 G gain antenna, defined 185 gateway current IP 53 Glossary 185191 GPS antenna 167 Configuration 45 defined 187 external GPS PPS option 9, 180 Firmware Version 116 information 116 latitude 63 longitude 63 Precise Positioning Service 116 pseudo-random noise 116 receiver 42 satellite fix 64 Serial Number 116 Status 111 Menu 116 Streaming Configuration 107 time of day 64 timing signals 42 to Console Baud Rate 107 UDP Server IP Address 107 UDP Server UDP Port 107 GROUP 63 H hand-off 71 Signal and Distance 71 Signal, Distance, and Bearing 71 Strict Connection 71 Strict Distance 71 Strict Signal 71 Hardware Event Triggers 103, 105 flow control, defined 187 05-4446A01, Rev. E Mercury Reference Manual I-3 Version 43 hop pattern 70, 145 pattern offset 70 Hopping Host frequency, defined 187 computer 86 computer, defined 188 HTTP Auth Mode 94 defined 188 Mode 94 HyperTerminal 36, 37 Hysteresis Margin 73, 75 I IANA 77 ICMP defined 188 IEEE 802.1Q 48, 49, 188 802.1X 188 defined 188 IEEE 802.1x Device Authentication 4, 51, 97 IETF standard RFC1213 58 IGMP 77 defined 188 Image Copy 128 file, defined 188 Verify 128 iNET II, differences of 158 Init/Hardware Error 105 Installation antenna & feedline 165 feedline selection 167 general information 5 mobile 9 planning 163 requirements 163 site selection 164 site survey 169 Interference 170 inter-frame packet delay 82 Internal Radio Status 111 Menu 120 Internet Inter-Packet Delay 79, 81, 82 IP 12, 50 Address 26, 42, 53, 134 Configuration 47 Mode 49, 50, 53 Configuration 46 current address 50, 53 gateway 50 netmask 50 gateway 53, 134 netmask 53 Protocol 80 static Assigned Numbers Authority 77 Control Message Protocol, defined 188 address 49 netmask 49 tunneling 76 K KEY command 157 transmitter, for antenna SWR check 157 L Lack of Associated Remotes Exceeded Threshold 104, 105 Menu 106 Lack of Remotes for 106 LAN defined 188 wireless 10, 12 LAT 63 Latency, defined 188 Latitude 116 LED COM1 30 LAN 29, 38, 39, 150 LINK 29, 30, 150, 159, 170 PWR 29, 30, 114, 150, 154, 155 use during troubleshooting 149 Local Area Network, defined 188 Console 36 session 37 Location 110, 135 logged events 155 LONG 63 Longitude 116 Lost Carrier Detected 115, 153 M MAC 63 ADDR 144 Main Menu 43 Maintenance/Tools 45 Menu 123 Manage Certificates 93 Management VLAN ID 49 VLAN Mode 49 VLAN Subnet Config 49 Management System 25, 76, 130 as a troubleshooting tool 150 user interfaces 33 manuals Reference Manual 3 Start-Up Guide 3 margin hysteresis 75 protection 75 Max Modulation 74 Transmit Power 66 Max Remotes 96 Maximum Receive Errors 106 MD5, defined 188 MDS Security Suite 17 measurements radio 157 Media Access Controller, defined 188 I-4 Mercury Reference Manual 05-4446A01, Rev. E MIB defined 188 files 33, 58 version II 58 mobile 9 Mobility defined 188 MODBUS 88 ASCII 90 RTU 90 Modbus TCP Server 88 Mode 63, 79 Device, defined 186 mixed 86 Model 109 modulation protection 75 MTBF, defined 189 multicast addressing 77 N NAME 63 NEMA 12 netmask current IP 53 network Administrator 9 Configuration 44 coverage 145 design 14 antennas 15 collocating multiple radio networks 16 name 15 repeaters 14 using multiple Access Points 16 Using the AP as a Store-and-Forward Packet Repeater 15 Using two transceivers to form a repeater station 14 Event Triggers 103, 104 Interface Config 46 Error 104 LAN 10 name 17, 23, 26, 66, 145 defined 189 tabletop 23 Time Protocol (NTP), defined 189 WAN 10

-wide diagnostics 189 NTP (Network Time Protocol), defined 189 Number of Satellites 116 O OFDM 4 OFFSET 63 optimizing radio performance 140 Orthogonal Frequency Division Multiplexing 4 Outgoing Connections Inactivity Timeout 81 P P23 8 Packet defined 189 Receive Errors Exceeded Threshold 104, 106 Menu 106 Size 135 Statistics 111, 114, 153 packets dropped 115, 153 received 115 sent 115 password admin 95 guest 95 Pattern Offset 145 PC connection to transceiver 25 host 86 peer-to-peer communications 10 Performance Information 45 Trend 111 PING 23, 30, 123, 170 address 135 defined 189 utility 124 PKI 189 PLC 13 defined 190 point-to-multipoint 16 defined 189 Point-to-Point LAN Extension 11 Link 11 Poll, defined 189 port access 48, 49 COM1 13, 25, 26, 27, 28, 33, 36, 38, 44, 76, 83, 88, 130, 165, 177 COM2 26, 83 Ethernet 23, 48, 49 GPS antenna 27, 29 IP 83 LAN 25, 26, 27, 28, 33, 36, 38, 39, 53, 76, 130, 165, 177 PWR 27, 28 RX2 27, 29, 167 serial 12 trunk 49 TX/RX1 antenna 27, 29 Portability, defined 189 power connector 24 how much can be used 169 primary 24 transmitter power output 157 PPS 116 Precise Positioning Service 116 PRN 116 Programmable Logic Controller 13 Protection Margin 73, 75 protocol DHCP 53 HTTP 33 HTTPS 33 ICMP 48 defined 188 IP 12, 26, 50, 76 SNMP 33, 48, 50, 58, 180 defined 190 05-4446A01, Rev. E Mercury Reference Manual I-5 SNTP 46, 191 SSH 33, 36 STP, defined 191 Syslog 113 TCP 76, 77, 81, 83, 86 defined 191 Telnet 33, 36, 38, 48 TFTP 48, 129 defined 191 UDP 76, 77, 83, 86 defined 191 Pseudo-Random Noise 116 PuTTY usage 41 defined 190 Q QoS 4 QPSK 75 Quality of Service 4 R Radio Configuration 44 Details 122 Event Triggers 103, 104 Frequency Interference 17 interference 170 Mode 139 performance optimization 140 Remote, defined 190 Test 125 RADIUS 190 configuration 93, 99 User Auth Mode 99 range, transmission 12 ranging 152 Read Community String 59 reboot Device 128 on upgrade 138 Remotes 138 errors 115, 153 power 66 receive defined 190 Redundancy Configuration 45, 103 Options 103, 105 Using multiple Access Points 16 Remote add 97 associated 97 approved 96 Database 118 delete 97 all 97 Max 6 Performance Database 118 radio, defined 190 Standard 6 Terminal Unit 13 defined 190 view approved 97 Repeater 14 Received Signal Strength Indicator 24, 165 antennas 15 Network Name 15 Using the AP as a Store-and-Forward Packet Repeater 15 Using two transceivers to form a repeater station 14 Reprogramming 124 Menu 126 Reset to Factory Defaults 124, 137 Retries 153 Retrieve Certificate 101 File 128, 134 Retry errors 153 RF bandwidth 26, 69 Output Power 26 power output level 24 RFI 17 defined 190 Roaming, defined 190 RSSI 24, 122, 143, 144, 158, 165 average 122 defined 190 RTU 13, 83, 87 defined 190 RX Frequency Offset 123, 144 IP Port 79 S satellite fix status 43, 116 number of 116 SCADA 12, 13, 77 defined 190 Scanning 152 script configuration 124 security Configuration 45 Menu 92 device level 97 general information 5 monitoring 13 password 25 risk management 18 suite 17 wireless access 97 Send Serial Event Log 113 file 134 GPS via UDP 107 Configuration Wizard 77 data baud rate 76 encapsulation 76 Number 43, 109 Port Configuration 44 radio networks, backhaul 11 server status 52 time 114 signal strength 165

-to-noise ratio 116 I-6 Mercury Reference Manual 05-4446A01, Rev. E defined 190 Simple Network Management Protocol, defined 190 Time Protocol 64 defined 191 Single channel operation 24 Frequency Channel 26, 70 SINGLE_CHAN 63 Site selection 164 SNMP 33, 50 Agent Config 46 defined 190 Mode 60 traps 183 usage 180 V3 Passwords 60 SNMPv3 180 accounts 181 SNR 73, 116, 122, 144 average 122 defined 190 max 75 min 75 range 75 defined 191 Server 46 SNTP configuration 64 Spanning Tree Protocol, defined 191 Spectrum Analyzer Mode 140 spread-spectrum transmission 5 SSH 36, 98 Access 94 defined 191 SSL, defined 191 Standing Wave Ratio 191 Starting Information Screen 38, 44 Static IP Address 49, 50, 53 Gateway 54 Netmask 49, 50, 53 Status 42, 79, 80, 81, 82 alarmed 152 associated 152 authenticating 152 connecting 152 scanning 152 STP, defined 191 Stream GPS to Console 107 subnet 53 SWR 157, 191 defined 191 performance optimization 157 Syslog Server Address 113 system gain, antenna (defined) 185 T tabletop network 23 TCP 76, 77, 86 client 77 defined 191 server 77 TDD Block Size 102 defined 191 Host Address 62, 101, 127, 130, 133, 134 Timeout 102 Sync Mode 15, 70, 145 TDD Sync 26 Telnet 36, 76, 83, 98 Access 94 session 38 Utility 125 Test Burst Percentage 139 Channel 139 Key 139 RF Bandwidth 139 Status 139 Transmit Power 139 TFTP Time 109 Connected 119 Division Duplex 70 server 114 Total FEC Count 123, 144 transceiver models 6 Transfer Options 101, 113 Transmission Control Protocol, defined 191 range 12 transmit max power 66 power 66, 122, 143 transparent encapsulation 76 Trap Community String 59 Manager 60 defined 191 Version 60 triggers hardware event 105 radio event 104 Troubleshooting 149157 TX Frequency Offset 122, 144 IP Address 79 Port 79 Uncorrected FEC Count 123, 144 Unit Password 26 upgrade U UDP 76, 83, 86 defined 191 mode 79 multicast 77 Point-to-Point 80 firmware 138 Uplink 144 Uptime 43, 109 User Auth Fallback 94 Auth Method 94 Authentication 98 Using the Embedded Management System 150 05-4446A01, Rev. E Mercury Reference Manual I-7 Datagram Protocol, defined 191 Passwords 94 Menu 95 User Auth Mode 99 UTC Time Offset 110 UTP, defined 191 V V3 View Authentication Password 60 Approved Remotes 97 Current Settings 78 Event Log 113 Menu 114 VLAN 48, 191 data 48, 49 Ethport Mode 49 ID 49 management 48, 49 Status 46, 47, 49 Voice over IP 4, 13 VoIP 4, 13 volts-dBm-watts conversion 174 W watts-dBm-volts conversion 174 Web browser 36, 76 session 39 Wireless LAN 10 Network Status 111 Menu 117 Security 93 Menu 95 wizard serial configuration 77 Write community String 59 Y Yagi antenna 166 I-8 Mercury Reference Manual 05-4446A01, Rev. E IN CASE OF DIFFICULTY... GE MDS products are designed for long life and trouble-free operation. However, this equipment, as with all electronic equipment, may have an occasional component failure. The following information will assist you in the event that servicing becomes necessary. TECHNICAL ASSISTANCE Technical assistance for GE MDS products is available from our Technical Support Department during business hours (8:00 A.M.5:30 P.M. Eastern Time). When calling, please give the complete model number of the radio, along with a description of the trouble/symptom(s) that you are experiencing. In many cases, problems can be resolved over the telephone, without the need for returning the unit to the factory. Please use one of the following means for product assistance:

Phone: 585 241-5510 FAX: 585 242-8369 E-Mail: GEmds.techsupport@GE.com Web: www.GEmds.com FACTORY SERVICE Component level repair of this equipment is not recommended in the field. Many components are installed using surface mount technology, which requires specialized training and equipment for proper servicing. For this reason, the equipment should be returned to the factory for any PC board repairs. The factory is best equipped to diagnose, repair and align your radio to its proper operating specifications. If return of the equipment is necessary, you must obtain a Service Request Order (SRO) number. This number helps expedite the repair so that the equipment can be repaired and returned to you as quickly as possible. Please be sure to include the SRO number on the outside of the shipping box, and on any corre-

spondence relating to the repair. No equipment will be accepted for repair without an SRO number. SRO numbers are issued online at www.GEmds.com/support/product/sro/. Your number will be issued immediately after the required information is entered. Please be sure to have the model number(s), serial number(s), detailed reason for return, "ship to" address, "bill to" address, and contact name, phone number, and fax number available when requesting an SRO number. A purchase order number or pre-payment will be required for any units that are out of warranty, or for product conversion. If you prefer, you may contact our Product Services department to obtain an SRO number:

Phone Number: 585-241-5540 Fax Number: 585-242-8400 E-mail Address: productservices@GEmds.com The radio must be properly packed for return to the factory. The original shipping container and packaging materials should be used whenever possible. All factory returns should be addressed to:

GE MDS, LLC Product Services Department

(SRO No. XXXX) 175 Science Parkway Rochester, NY 14620 USA When repairs have been completed, the equipment will be returned to you by the same shipping method used to send it to the factory. Please specify if you wish to make different shipping arrangements. To inquire about an in-process repair, you may contact our Product Services Group using the telephone, Fax, or E-mail information given above. GE MDS, LLC 175 Science Parkway Rochester, NY 14620 FAX: +1 585 242-9620 Web: www.GEmds.com General Business: +1 585 242-9600