A i r Te m p o Wireless Touch Control with Steamhead Installation, Operation & Maintenance Manual 1 mr.steam Installation, Operating & Maintenance Instructions________________________________________________________________________________________________ When installing and using this electrical equipment, basic safety precautions should always be followed, including the following:
IMPORTANT SAFETY INSTRUCTIONS 1. READ AND FOLLOW ALL INSTRUCTIONS 2. thermia). Limit your use of steam to 10-15 minutes until you are certain of your bodys reaction. Do not permit children under the age WarNiNG 3. WarNiNG
!
of 16 to use this steambath.
!
Steam is hot and can cause injury or death if improperly used. Steam rooms contain steam and elevated temperatures. Please read and observe all warnings in this manual before installing or using a steam room.
!
To reduce the risk of injury:
4. A. The wet surfaces of steam enclosures may be slippery. WarNiNG Use care when entering or leaving. B. The steam head is hot. Do not touch the steamhead and avoid the steam near the steamhead. C. Prolonged use of the steam system can raise excessively the internal human body temperature and impair the bodys ability to regulate its internal temperature (hyper-
SAVE THESE INSTRUCTIONS 2 D. Excessive temperatures have a high potential for causing fetal damage during the early months of pregnancy. Pregnant or possibly pregnant women should consult a physician regarding correct exposure. E. Obese persons and persons with a history of heart disease, low or high blood pressure, circulatory system problems, or diabetes should consult a physician before using a steambath. F. Persons using medication should consult a physician before using a steambath since some medication may induce drowsiness while other medications may affect heart rate, blood pressure and circulation. HypertHermia occurs when the internal temperature of the body reaches a level several degrees above the normal body temperature of 98.6 F. The symptoms of hyperthermia include an increase in the internal temperature of the body, dizziness, lethargy, drowsiness, and fainting. The effects of hyperthermia include:
a) Failure to perceive heat;
b) Failure to recognize the need to exit the steam-
bath;
c) Unawareness of impending risk;
d) Fetal damage in pregnant women;
e) Physical inability to exit the steambath; and f) Unconsciousness. WarNiNG The use of alcohol, drugs, or medi-
!
cation can greatly increase the risk of hyperthermia. reaD me FirSt!
WarNiNG
!
As you follow these instructions, you will notice warning and caution symbols. This blocked information is important for the safe and ef-
ficient installation and operation of the steambath system. These are types of potential hazards that may occur during installation and operation:
WarNiNG
!
result in death or serious injury. Indicates a potentially hazardous situation, which could CaUtiON
!
in minor or moderate injury or product damage. Indicates a potentially hazardous situation, which may result impOrtaNt NOte: This highlights information that is especially relevant to a problem-free installation. All information in these instructions is based on the latest product informa-
tion available at the time of publication. Sussman-Automatic Corporation reserves the right to make changes at any time without notice. table of Contents:
Important Safety Instructions ...................................2 Before Installing .......................................................4 Dimensional Information .........................................5 Installation - Flush Mount, Surface Mount ........... 6-7 Installing the Remote Temperature Probe ........ 8-10 AirTempo Operating Instructions .................... 11-13 Battery Replacement .............................................14 System Status Codes .............................................15 Care and Maintenance, Warranty ..........................15 Parts List ...............................................................17 Template ...............................................................17 Glass Mount Mask ........................................... 18-19 3 mr.steam Installation, Operating & Maintenance Instructions________________________________________________________________________________________________mr.steam Installation, Operating & Maintenance Instructions________________________________________________________________________________________________ mr.steam CaUtiON WarNiNG room a Remote Temperature Probe (PN MSTS) must be installed inside the steam room per instructions for the Remote Temperature Probe. Failure to install according to instructions will result in an inoperative control and overheating of the steam room.
!
Do not route AirTempo, iSteam, iTempoPlus, iTempo, Home Wizard or iGenie control wiring inside conduit together with power lines or close to hot water or steam piping. Doing so may result in an inoperative or hazardous installation.
!
an inoperative or hazardous installation and will void the warranty. Installation Instructions ________________________________________________________________________________________________ Before installing Carefully inspect the control and packaging for shipping damage. In the event of shipping damage, please contact the carrier for claim information. Our customer service department can assist you with any missing or damaged parts.
!
To avoid unintentional steambath operation, do not locate the control where other controls, accessories, shower heads, valves, body sprays or similar within the shower could cause confusion or interfere with the MrSteam controls intended use and function. Do not use any AirTempo, iSteam, iTempoPlus, iTempo, HomeWizard or iGenie controls without reading and understanding the respective Installation and Operation Manual and MrSteam steam generator Installation and Operation Manual. Failure to read and understand these instructions may result in an inoperative or hazardous installation.
!
generator Installation, Operation and Maintenance Manual. This manual is pro-
vided with every steam generator. The warning sticker must be read and perma-
nently affixed in a conspicuous location near the steam room. Failure to read and affix this warning sticker in a conspicuous location may result in serious injury or death. Please call MrSteam at 800 767-8326 for a free replacement or if you have any questions regarding the warning sticker. Install the AirTempo, iSteam, iTempo or iTempoPlus controls according to installa-
tion instructions. Failure to install according to instructions will result in an inopera-
tive control or hazardous overheating or inadequate heating of the steam room. If an AirTempo, iSteam, iTempo or iTempoPlus control is installed outside the steam 4 Do not operate AirTempo, iTempoPlus, iTempo, Home Wizard or iGenie controls with anything other than a MrSteam eTempo compatible steam generator. MrSteam resi-
dential steam generators with serial numbers lower than 900000, or any other brand of steam generator are not to be operated with AirTempo, iTempoPlus, iTempo, Home Wizard or iGenie controls. Doing so may result in an inoperative installation. This document contains important safety, operation and maintenance information. impOrtaNt NOteS:
Turn power to the steam generator OFF before connecting the control to the damaged or otherwise not functioning properly. Doing so may result in an inopera-
tive or hazardous installation. Discontinue use of the steam generator or control if the steam generator is Leave this document with the homeowner. Do not discard this document. generator. Failure to turn the power off will result in an inoperable control. Do not alter or modify any Mr. Steam product. Doing so may result in A peel and stick warning sticker is provided in the MrSteam steam All drawings are for illustrative purposes only. WarNiNG WarNiNG mr.steam Installation Instructions ________________________________________________________________________________________________ Dimensional information for the airtempo BOx CONteNtS:
AirTempo Control Decorative Trim Cable (3 ft.) Wireless Receiver Batteries (2) Mouting Screws (2) Steam head Tube of Silicone Sealant Owners Manual Surface Mount Bayonet 3-5/8 1-5/8 7/8 3-5/8 3/4 4-7/8 AirTempo Wireless Receiver Drawings for illustrative purposes only 5 mr.steam Installation Instructions ________________________________________________________________________________________________ installation instructions for airtempo Step 1 Determine the desired installation location of the control. The AirTempo controls are designed to be installed inside or outside the steam room as a matter of personal preference. If the control is installed outside the steam room a Remote Temperature Probe part number MSTS must be installed inside the steam room. impOrtaNt NOte: See installation instructions for the MSTS Temperature Probe (pgs. 8-9) before rough-in or installation of control. If the control is installed inside the steam room the control must be located:
4-5 feet above the floor near the bather seating area. On a vertical wall The control features an integral temperature sensor. Locate the control in a location representative of the desired steam bathing temperatures. Do not locate the control above or near the steam head or direct steam emissions. Locating the controls near the steamhead or near direct steam emissions may result in poor steam room temperature control. The control can be located up to 60 feet from the wireless receiver. Construction materials affect the communication between the control and receiver. Test the range of the AirTempo. It may be necessary to change the location of the wireless receiver to improve the range. Contact MrSteam technical service for an optional 30 or 60 foot cable. 6 Step 2 The AirTempo control can be surface or flush mounted according to personal preference. Flush mount components are sold separately
(104232DR & 104232SQ). Contact a MrSteam representative if a flush mount kit is needed. Surface mount airtempo Remove the surface mount bayonet from the back of the AirTempo Control. Remove and discard the release paper to expose the adhesive liner. Ensure the mounting surface is clean and dry. Place the bayonet on the wall in the desired location. impOrtaNt NOte: The surface mount bayonet supports the weight of the AitTempo control, if requires use the screw and anchor provided to secure the bayonet to the wall. When installing AirTempo on glass, the peel and stick film provided may be used as a mounting pad for a clean look from behind the glass. mr.steam Installation Instructions ________________________________________________________________________________________________ Flush mount airtempo impOrtaNt NOte: Flush mount components are sold separately
(104232RD & 104232SQ). Contact a MrSteam representative if a flush mount kit is needed. Remove the surface mount bayonet from the back of the AirTempo control. The surface mount bayonet is not used with flush mounting. Using the template provided on page 17, cut the hole in the desired location. Do not oversize or undersize the cutout. Ensure the template is level before cutting the hole. Test fit the flush mount box to ensure the hole is the correct size. Ensure the mounting surface is clean and dry Apply a thin bead of silicone in the location shown as required to create a moisture seal. Remove and discard the release paper to expose the adhesive liner. NOte: The silicone supplied by MrSteam can be used for a variety of sealing and gasketing. It cures to silicone rubber and adheres to glass, wood, metal, porcelain, ceramic tile, painted surfaces, many plastics and rubber. Surfaces must be clean and dry. Apply thin layer of product. Fit together and support if necessary. Allow excess material to cure, then trim with a sharp blade. Sealant skins in 5 minutes, dries to touch in 1 hour. Fully cures and bonds in 24 hrs. impOrtaNt NOte: Do not apply excessive amounts of silicone. Do not apply silicone to any other parts of the control including the adhesive gasket. Place the flush mount box into the hole. impOrtaNt NOte: The magnet in the flush mount box should be orientated at the bottom of the box when installed. Magnet Place the electronic assembly into the decorative bezel as shown. The retention ring snaps onto the assembly from behind. The 3 piece assembly can then be placed into the flush mount box. There is a magnet in the box that will hold the control in place. 7 mr.steam Installation Instructions ________________________________________________________________________________________________ mr.steam Installation Instructions ________________________________________________________________________________________________ installing the remote temperature probe (PN: MSTS) The Remote Temperature Probe is required when the AirTempo control is installed outside the steam room. CaUtiON The Remote Temperature Probe is for use with AirTempo,
!
iTempo and iTempoPlus controls only. Do not use with any other controls. Do not use any other temperature probe with the AirTempo, iTempo and iTempoPlus controls. Noncompatible products may result in an inoperative control and a hazardous condition. CaUtiON
!
Install the AirTempo controls according to the installation instructions on pages 4-7. Failure to do so may result in an inoperative control and a hazardous condition. 1. Determine the location of the Remote Temperature Probe:
The Remote Temperature Probe must be installed:
a. On a vertical surface b. 4-5 feet above the floor c. in a location representative of the desired steam bathing temperature. Locating the MSTS near the steamhead or near direct steam emis-
sions may result in poor steam room temperature control. d. The probe has an integral 30 cable. Insure that the probe and/or steam generator are located accordingly. 8 2. Drill a 5/16 inch diameter hole in the wall. Do not oversize or under size the hole. Clean area thoroughly. NOte: The silicone supplied by MrSteam can be used to meet a variety of sealing and gasketing. It cures to silicone rubber and adheres to glass, wood, metal, porcelain, ceramic tile, painted surfaces, many plastics and rubber. Surfaces must be clean and dry. Apply thin layer of product. Fit together and support if necessary. Allow excess material to cure, then trim with a sharp blade. Sealant skins in 5 minutes, dries to touch in 1 hour. Fully cures and bonds in 24 hrs. 3. Remove the knock-out from the steam generator jacket as shown in Diagram 1. 4. Insert the probe cable through the knock-out and connect to the connector on the steam generator printed circuit board marked EXT TEMP as shown in Diagram 1. DiaGram 1 Mr.Steam Steam Generator
(shown with cover removed and NOT installed) Temperature Probe Connection Knock-Out Temperature Probe Cable
(30 feet) Temperature Sensor Probe Drawings for Illustrative Purposes Only. 9 mr.steam Installation Instructions ________________________________________________________________________________________________ mr.steam Operating Instructions ________________________________________________________________________________________________ 5. Route the end of the probe cable with the temperature probe through the wall into the steam room as shown in Diagram 2. impOrtaNt NOte: Do not strain, staple, pinch or otherwise damage the probe cable. 6. With a minimal length of the cable exposed apply silicone
(provided) to the hole in the wall as required to create a mois-
ture seal as shown in Diagram 2. 7. Push the temperature cable and probe into hole as required to leave minimum 1/4, maximum 1/2 of the bulb exposed as shown in Diagram 3. steam room interior WarNiNG Insure a minimum of 1/4 of the temperature probe is exposed
!
to the air. Failure to do so may interfere with the ability to sense tempera-
ture and may result in excessive steam room temperatures. WarNiNG
!
The exposed area of the temperature probe must be free of silicone or any materials or obstructions that prevent direct exposure to the steam room air. Failure to do so may interfere with the ability to sense tem-
perature and may result in excessive steam room temperatures. NOte: For Illustrative Purposes Only. Drawings Not to Scale 14" minimum 12" maximum Silicone Sealant Diagram 2 Diagram 3 10 Wall Cable Sectional View installed remote temperature probe showing a minimum of 1/4 of the probe exposed to steam room air airtempo Operating instructions The AirTempo features programmable temperature control, programmable time duration, AromaSteam ON/OFF, ChromaSteam control and two personal settings. The LCD will be OFF until a button is pressed. The LCD remains lit for 10 seconds after the last button is pressed. When the steam generator turns OFF the display will turn on and read OFF. While the generator is steaming the LED above AROMA and CHROMA will alternately flash every 2 seconds. WarNiNG Set the steam bathing temperature
!
according to personal preference, however it is highly recommended to begin steam bathing at a low temperature setting for a very short duration to gauge comfort and safety levels. Diagram 1 Diagram 2 ON/OFF Diagram 1 Press the ON/OFF key for 1 second to start the flow of steam. The Temperature Set Point is displayed. Steam will begin to flow a few minutes after the control is turned ON. The duration re-
quired for the steam room to reach steam bathing temperatures depends on the steam room construction and steam generator specifications. To stop the flow of steam before time expires press the ON/OFF key. Steam may continue to flow for a short time after the control is turned OFF SettiNG tHe SteamBatH DUratiON Diagram 2 Press TIME key to set or display the steambath duration time. The control is pre-set and will display a TIME setting of 20 minutes (default setting). With the TIME displayed, press the LEFT or RIGHT arrows to set the desired duration time (2-60 minutes) in two minute increments. ON/OFF Time 11 mr.steam Operating Instructions ________________________________________________________________________________________________ mr.steam Operating Instructions ________________________________________________________________________________________________ Diagram 3 Diagram 4 SettiNG tHe temperatUre Diagram 3: Press TEMP key to set the desired temperature or display the temperature setting. The control is preset and will display a temperature setting of 110F (default setting). With the temperature displayed, press the LEFT or RIGHT arrows to set the desired temperature (80F to 120F) in one degree increments. Set the steam bathing temperature according to personal preference, however it is highly recommended to begin steam bathing at a low temperature setting to gauge comfort and safety levels. memOry FeatUre If the control is turned off manually before it times out then the default settings of 20 minutes and 110F will be used the next time the control is turned on. If the control times out (not manually turned off) then the previous user time and temperature settings will be used when the steambath is turned on. USer preSetS Diagram 4 Use the key program to store preferred settings. To program preferred settings:
Press ON/OFF key to turn generator on. Press key once to program PROG1. Press it twice to program PROG2. The selected setting will be displayed. Enter the preferred time and temperature settings. The AirTempo will store the following settings: Set point, Time duration & Aroma state. To select PROG1 or PROG2:
Press ON/OFF key then press key once to select PROG1, press it twice to select PROG2. The steambath will operate at the stored settings. 12 TEMP Time &
Temperature adjustment User Preset AROMA arOmaSteam The AromaSteam is an optional accessory that automatically injects aromatic oil into the steam. Press the ON/OFF key to turn the steam generator on. Then, press the AROMA key. The Aroma indicator will turn ON. The AromaSteam turns off automatically when the steam generator stops heating. Press the AROMA key to turn it off during a steam session. The in-
dicator will turn off. To conserve battery life, the indicator will only be lit when the display is ON. CHROMA CHrOmaSteam The ChromaSteam is an optional accessory that provides colored light in the steam room. Press the CHROMA key to turn light on. Press twice to select the next color. Press again to turn the light off. Note that the light can be turned ON even if the steam generator is OFF. To conserve battery, the indicator will only be lit when the display is ON. CHaNGiNG tHe temperatUre UNitS (F/C) When the generator is OFF, press and hold the TEMP key for 5 seconds. The temperature units will toggle to Fahrenheit (F) or Celsius (C). TEMP USiNG airtempO aS a remOte The AirTempo can be removed from its holder and used as a remote control to warm up the steam shower. When AirTempo is returned to its holder the steam generator will run for the full set duration. After 10 min-
utes the steam generator turns off if the AirTempo is not returned to its dock. The steam generator will not restart unless AirTempo is in its dock. USiNG iGeNie WitH airtempO iGenie will allow the steam generator to warm up the steam room for 10 minutes. To continue the steam bath session press any button on the AirTempo control. After 10 minutes the steam generator turns off if the AirTempo is not touched. The steam generator will not restart unless AirTempo is in its dock. 13 mr.steam Maintenance Instructions ________________________________________________________________________________________________ mr.steam Maintenance Instructions ________________________________________________________________________________________________ Battery replacement The batteries in AirTempo will need periodic replacement. Both batteries should be replaced at the same time with new CR2450 coin cell batteries.
!
pieces, keep out of reach of children. CHOKE HAZARD. The batteries and battery doors are small WarNiNG WarNiNG KEEP BATTERIES OUT OF REACH OF CHILDREN.
!
Swallowing may lead to serious injury or death in as little as 2 hours due to chemical burns and potential perforation of the esophagus. Immediately see a doctor. Remove the AirTempo from the wall by sliding it up and off the bayonet holder. The AirTempo comes off the flush mount holder by grasping the bezel and pulling the assembly straight out of the flush mount box. Use a soft cloth to dry off the control. With two fingers turn the battery doors in the direction noted. The left battery cover is opened by turning it clockwise, the right cover is opened by turning it counterclockwise. Discard both batteries and replace with new batteries, the positive side of the battery goes towards the + symbol on the battery door. 14 Replace the battery door and lock in place. CaUtiON To prevent water from getting in the control in-
!
gress, ensure the battery doors are in the locked position before reinstalling control. System Status Codes The AirTempo may display a status code if the steam system is not function-
ing correctly. err C indicates the AirTempo control has lost communication with the steam generator. Ensure all connections are secure between the steam generator and the transceiver err p indicates an error while pairing, reset the control and redo pairing. A complete list of steam generator status codes can be found in the MrSteam Residential Steambath Installation Operation and Maintenance Manual. pairing AirTempos are factory paired, however if more than one steam system is installed in close proximity the AirTempo controls must be paired to their transceivers to prevent interference. To pair AirTempo use a blunt object to press the button inside the transceiver adjacent to the LED. Hold the button for 5 seconds, when the transceiver is in pairing mode the LED will turn blink blue for 2 minutes. While the transceiver LED is blinking, press and hold the button on AirTempo for 5 seconds until the display reads PAIR. Care tips for airtempo Controls and Steamheads 1. Use only mild soap and water on a soft cloth to clean the control and steamhead. 2. Do not use abrasive cleansers 3. If the decorative cover is damaged call MrSteam technical service for replacement parts. Warranty To register your steam generator unit online and to review the MrSteam Limited Lifetime Warranty please go to:
blog.mrsteam.com/wr 15 mr.steam Maintenance Instructions ________________________________________________________________________________________________ mr.steam Maintenance Instructions ________________________________________________________________________________________________ FCC/industry Canada two part Statement:
This device complies with FCC Part 15 and Industry Canada license exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interfer-
ence, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR dIndustrie Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes: (1) lappareil ne doit pas produire de brouillage, et (2) lutilisateur de lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. per industry Canada rSS rules:
This device complies with Health Canadas Safety Code. The installer of this device should ensure that RF radiation is not emitted in excess of the Health Canadas requirement. Cet appareil est conforme avec Sant Canada Code de scurit 6. Le pro-
gramme dinstallation de cet appareil doit sassurer que les rayonnements RF nest pas mis au-del de Iexigence de Sant Canada. Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. Les changements ou modifications non expressment approuvs par la partie responsable de la conformit pourraient annuler lautorit de lutilisateur utiliser cet quipement. NOte: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio fre-
quency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equip-
ment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numrique de la classe B est conforme la norme NMB-003 du Canada template For Flush Mount Kit Installation DESCRIPTION parts List:
ITEM #
104208BK Electronic Assembly Black 104208WH Electronic Assembly White 104209 104210 104211 104212 Wireless Receiver 104213XX Round Bezel (AirTempo Flush) 104214XX Square Bezel (AirTempo Flush) 104215XX Surface Bezel (AirTempo Surface) 104220 AirTempo Cable Retention Ring (AirTempo Flush) Flush Mount Box (AirTempo Flush) Surface Mount Holder (AirTempo Surface) Surface Mount USED ON All All Flush Mount Flush Mount All Flush mount (specify finish) Flush mount (specify finish) Surface mount (specify finish) All 16 17 18 19 www.mrsteam.com Products, information and specifications are subject to change without notice. For more information call Sales & Support at: 1.800.76.STEAM (East Coast) 1.800.72.STEAM (West Coast) mr.steam Sussman-Automatic Corporation hello@mrsteam.com www.mrsteam.com 43-20 34th Street, Long island City NY 11101 9410 S. La Cienega Blvd., Inglewood CA 90301 800 767 8326 fax: 718 472 3256 800 72 8326 fax: 310 216 2944 PN 100503 rev 1.16