all | frequencies |
|
exhibits | applications |
---|---|---|---|---|
manual |
app s | submitted / available | |||||||
---|---|---|---|---|---|---|---|---|
1 |
|
01 alas5 hio user manual | Users Manual | 771.15 KiB | August 22 2019 / February 17 2020 | delayed release | ||
1 | ID Label/Location Info | August 22 2019 | ||||||
1 | 03 alas5-am schematic | Schematics | August 22 2019 | confidential | ||||
1 | 04 alas5-am faceplan | Block Diagram | August 22 2019 | confidential | ||||
1 | 05 alas5-am parts list | Parts List/Tune Up Info | August 22 2019 | confidential | ||||
1 | Test Report | August 22 2019 | ||||||
1 | Test Report | August 22 2019 | ||||||
1 | Test Report | August 22 2019 | ||||||
1 | 2456ERM.011 RF FCC 22 Photographs | Test Setup Photos | August 22 2019 / February 17 2020 | delayed release | ||||
1 | Test Report | August 22 2019 | ||||||
1 | Test Report | August 22 2019 | ||||||
1 | Test Report | August 22 2019 | ||||||
1 | Test Report | August 22 2019 | ||||||
1 | 2456ERM.012 RF FCC 24 Photographs | Test Setup Photos | August 22 2019 / February 17 2020 | delayed release | ||||
1 | Test Report | August 22 2019 | ||||||
1 | Test Report | August 22 2019 | ||||||
1 | Test Report | August 22 2019 | ||||||
1 | Test Report | August 22 2019 | ||||||
1 | Test Report | August 22 2019 | ||||||
1 | Test Report | August 22 2019 | ||||||
1 | Test Report | August 22 2019 | ||||||
1 | Test Report | August 22 2019 | ||||||
1 | Test Report | August 22 2019 | ||||||
1 | Test Report | August 22 2019 | ||||||
1 | Test Report | August 22 2019 | ||||||
1 | Test Report | August 22 2019 | ||||||
1 | Test Report | August 22 2019 | ||||||
1 | Test Report | August 22 2019 | ||||||
1 | Test Report | August 22 2019 | ||||||
1 | Test Report | August 22 2019 | ||||||
1 | Test Report | August 22 2019 | ||||||
1 | Test Report | August 22 2019 | ||||||
1 | Test Report | August 22 2019 | ||||||
1 | Test Report | August 22 2019 | ||||||
1 | Test Report | August 22 2019 | ||||||
1 | Test Report | August 22 2019 | ||||||
1 | Test Report | August 22 2019 | ||||||
1 | Test Report | August 22 2019 | ||||||
1 | Test Report | August 22 2019 | ||||||
1 | Test Report | August 22 2019 | ||||||
1 | 2456ERM.013 RF FCC 27 Photographs | Test Setup Photos | August 22 2019 / February 17 2020 | delayed release | ||||
1 | Test Report | August 22 2019 | ||||||
1 | RF Exposure Info | March 09 2020 / August 22 2019 | ||||||
1 | AA.162.301111 specs | Operational Description | August 22 2019 | confidential | ||||
1 | Cover Letter(s) | August 22 2019 | ||||||
1 | LPBEM-7-27 specs | Operational Description | August 22 2019 | confidential | ||||
1 | Operational description - v1 | Operational Description | August 22 2019 | confidential | ||||
1 | alas5-am block diagram | Block Diagram | August 22 2019 | confidential | ||||
1 | alas5-am external photos | External Photos | August 22 2019 / February 17 2020 | delayed release | ||||
1 | Cover Letter(s) | August 22 2019 | ||||||
1 | Cover Letter(s) | August 22 2019 | ||||||
1 | Cover Letter(s) | August 22 2019 | ||||||
1 | Cover Letter(s) | August 22 2019 | ||||||
1 | alas5-am internal external photos | Internal Photos | August 22 2019 / February 17 2020 | delayed release | ||||
1 | alas5-am tune up procedure | Parts List/Tune Up Info | August 22 2019 | confidential | ||||
1 | Cover Letter(s) | August 22 2019 |
1 | 01 alas5 hio user manual | Users Manual | 771.15 KiB | August 22 2019 / February 17 2020 | delayed release |
Cinterion ALAS5 Hardware Interface Description Version:
DocId:
00.030a ALAS5_HIO_v00.030a GEMALTO.COM/M2M Cinterion ALAS5 Hardware Interface Overview Page 2 of 50 2 Document Name: Cinterion ALAS5 Hardware Interface Overview Version:
00.030a Date:
DocId:
Status 2019-04-01 ALAS5_HIO_v00.030a Confidential / Preliminary GENERAL NOTE THE USE OF THE PRODUCT INCLUDING THE SOFTWARE AND DOCUMENTATION (THE "PROD-
UCT") IS SUBJECT TO THE RELEASE NOTE PROVIDED TOGETHER WITH PRODUCT. IN ANY EVENT THE PROVISIONS OF THE RELEASE NOTE SHALL PREVAIL. THIS DOCUMENT CONTAINS INFORMATION ON GEMALTO M2M PRODUCTS. THE SPECIFICATIONS IN THIS DOCUMENT ARE SUBJECT TO CHANGE AT GEMALTO M2M'S DISCRETION. GEMALTO M2M GMBH GRANTS A NON-
EXCLUSIVE RIGHT TO USE THE PRODUCT. THE RECIPIENT SHALL NOT TRANSFER, COPY, MODIFY, TRANSLATE, REVERSE ENGINEER, CREATE DERIVATIVE WORKS; DISASSEMBLE OR DECOMPILE THE PRODUCT OR OTHERWISE USE THE PRODUCT EXCEPT AS SPECIFICALLY AUTHORIZED. THE PRODUCT AND THIS DOCUMENT ARE PROVIDED ON AN "AS IS" BASIS ONLY AND MAY CONTAIN DEFICIENCIES OR INADEQUACIES. TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, GEMALTO M2M GMBH DISCLAIMS ALL WARRANTIES AND LIABILITIES. THE RECIPIENT UNDERTAKES FOR AN UNLIMITED PERIOD OF TIME TO OBSERVE SECRECY REGARDING ANY INFORMATION AND DATA PROVIDED TO HIM IN THE CONTEXT OF THE DELIV-
ERY OF THE PRODUCT. THIS GENERAL NOTE SHALL BE GOVERNED AND CONSTRUED ACCORDING TO GERMAN LAW. Copyright Transmittal, reproduction, dissemination and/or editing of this document as well as utilization of its con-
tents and communication thereof to others without express authorization are prohibited. Offenders will be held liable for payment of damages. All rights created by patent grant or registration of a utility model or design patent are reserved. Copyright 2019, Gemalto M2M GmbH, a Gemalto Company Trademark Notice Gemalto, the Gemalto logo, are trademarks and service marks of Gemalto and are registered in certain countries. Microsoft and Windows are either registered trademarks or trademarks of Microsoft Corpora-
tion in the United States and/or other countries. All other registered trademarks or trademarks mentioned in this document are property of their respective owners. ALAS5_HIO_v00.030a Confidential / Preliminary 2019-04-01 Cinterion ALAS5 Hardware Interface Overview Contents 50 Page 3 of 50 Contents 1 2 3 4 5 Introduction ................................................................................................................. 7 Product Variants ................................................................................................ 7 1.1 Key Features at a Glance .................................................................................. 8 1.2 Supported Frequency Bands .............................................................. 12 1.2.1 1.2.2 Supported CA Configurations ............................................................. 13 ALAS5 System Overview................................................................................. 15 1.3 Interface Characteristics .......................................................................................... 16 2.1 Application Interface ........................................................................................ 16 2.1.1 USB Interface...................................................................................... 16 Serial Interface ASC0 ......................................................................... 17 2.1.2 2.1.3 Serial Interface ASC1 ......................................................................... 18 2.1.4 Inter-Integrated Circuit Interface ......................................................... 19 2.1.5 UICC/SIM/USIM Interface................................................................... 20 2.1.6 Digital Audio Interface......................................................................... 22 2.1.6.1 Pulse Code Modulation Interface (PCM)............................. 22 2.1.6.2 Inter-IC Sound Interface...................................................... 22 2.1.7 Analog-to-Digital Converter (ADC)...................................................... 22 2.1.8 GPIO Interface .................................................................................... 22 2.1.9 eMMC Interface .................................................................................. 22 GSM/UMTS/LTE Antenna Interface................................................................. 23 2.2.1 Antenna Installation ............................................................................ 24 2.2.2 RF Line Routing Design...................................................................... 25 2.2.2.1 Line Arrangement Instructions ............................................ 25 2.2.2.2 Routing Examples ............................................................... 27 GNSS Antenna Interface ................................................................................. 28 Sample Application .......................................................................................... 30 2.3 2.4 2.2 GNSS Interface .......................................................................................................... 32 Mechanical Dimensions and Mounting................................................................... 33 4.1 Mechanical Dimensions of ALAS5................................................................... 33 Regulatory and Type Approval Information ........................................................... 35 Directives and Standards................................................................................. 35 5.1 5.2 SAR requirements specific to portable mobiles ............................................... 38 Reference Equipment for Type Approval ......................................................... 39 5.3 5.4 Compliance with FCC and ISED Rules and Regulations................................. 40 ALAS5_HIO_v00.030a Confidential / Preliminary 2019-04-01 Cinterion ALAS5 Hardware Interface Overview Contents 50 Page 4 of 50 6 7 Document Information.............................................................................................. 43 Revision History ............................................................................................... 43 6.1 6.2 Related Documents ......................................................................................... 44 Terms and Abbreviations ................................................................................. 44 6.3 6.4 Safety Precaution Notes .................................................................................. 47 Appendix.................................................................................................................... 48 List of Parts and Accessories........................................................................... 48 7.1 ALAS5_HIO_v00.030a Confidential / Preliminary 2019-04-01 Cinterion ALAS5 Hardware Interface Overview Tables 50 Page 5 of 50 Tables Table 1:
Table 2:
Table 3:
Table 4:
Table 5:
Table 6:
Table 7:
Table 8:
Table 9:
Table 10:
Table 11:
Table 12:
Table 13:
Table 14:
Table 15:
Supported frequency bands for each product variant .................................... 12 Supported CA configurations ......................................................................... 13 Signals of the SIM interface (SMT application interface) ............................... 20 Return loss in the active band........................................................................ 23 Directives ....................................................................................................... 35 Standards of North American type approval .................................................. 35 Standards of European type approval............................................................ 36 Requirements of quality ................................................................................. 36 Standards of the Ministry of Information Industry of the Peoples Republic of China ............................................................................ 37 Toxic or hazardous substances or elements with defined concentration limits ............................................................................................................... 37 Antenna gain limits for FCC for ALAS5-W (TBD.).......................................... 40 Antenna gain limits for FCC and ISED for ALAS5-AM (TBD.) ....................... 41 List of parts and accessories.......................................................................... 48 Molex sales contacts (subject to change) ...................................................... 49 Hirose sales contacts (subject to change) ..................................................... 49 ALAS5_HIO_v00.030a Confidential / Preliminary 2019-04-01 Cinterion ALAS5 Hardware Interface Overview Figures 50 Page 6 of 50 Figures Figure 1:
Figure 2:
Figure 3:
Figure 4:
Figure 5:
Figure 6:
Figure 7:
Figure 8:
Figure 9:
Figure 10:
Figure 11:
Figure 12:
Figure 13:
Figure 14:
Figure 15:
Figure 16:
ALAS5 system overview ................................................................................ 15 USB circuit ..................................................................................................... 16 Serial interface ASC0..................................................................................... 17 Serial interface ASC1..................................................................................... 18 I2C interface connected to VEXT ................................................................... 19 First UICC/SIM/USIM interface ...................................................................... 21 Second UICC/SIM/USIM interface ................................................................. 21 Embedded Stripline line arrangement............................................................ 25 Micro-Stripline line arrangement samples...................................................... 26 Routing to applications RF connector ........................................................... 27 Supply voltage for active GNSS antenna....................................................... 28 ESD protection for passive GNSS antenna ................................................... 29 ALAS5 sample application ............................................................................. 31 ALAS5 top and bottom view........................................................................ 33 Dimensions of ALAS5 (all dimensions in mm) ............................................... 34 Reference equipment for type approval ......................................................... 39 ALAS5_HIO_v00.030a Confidential / Preliminary 2019-04-01 Cinterion ALAS5 Hardware Interface Overview 1 Introduction 15 1 Introduction Page 7 of 50 This document1 describes the hardware of the Cinterion ALAS5 module. It helps you quickly retrieve interface specifications, electrical and mechanical details and information on the re-
quirements to be considered for integrating further components. 1.1 Product Variants This document applies to the following Gemalto M2M modules:
Cinterion ALAS5-W Cinterion ALAS5-AM Where necessary a note is made to differentiate between the various product variants and re-
leases. 1. The document is effective only if listed in the appropriate Release Notes as part of the technical docu-
mentation delivered with your Gemalto M2M product. ALAS5_HIO_v00.030a Confidential / Preliminary 2019-04-01 Page 8 of 50 Cinterion ALAS5 Hardware Interface Overview 1.2 Key Features at a Glance 15 1.2 Key Features at a Glance Feature General Frequency bands Implementation Note: Not all of the frequency bands (and 3GPP technologies) mentioned throughout this document are supported by every ALAS5 product variant. Please refer to Section 1.2.1 for an overview of the frequency bands sup-
ported by each ALAS5 product variant. GSM class Small MS Output power
(according to Release 99) GSM/GPRS/UMTS:
Class 4 (+33dBm 2dB) for EGSM850 and EGSM900 Class 1 (+30dBm 2dB) for GSM1800 and GSM1900 Class E2 (+27dBm 3dB) for GSM 850 8-PSK and GSM 900 8-PSK Class E2 (+26dBm +3 /-4dB) for GSM 1800 8-PSK and GSM 1900 8-PSK Class 3 (+24dBm +1/-3dB) for all supported WCDMA FDD bands Output power
(according to Release 4) TD-SCDMA:
Class 2 (+24dBm +1/-3dB) for TD-SCDMA 1900 (Bd39) and TD-SCDMA 2000 (Bd34) Output power
(according to Release 8) LTE (FDD):
Class 3 (+23dBm 2dB) for all supported LTE FDD bands LTE (TDD):
Class 3 (+23dBm 2dB) for all supported LTE TDD bands Power supply Operating temperature
(board temperature) 3.3V < VBATT+ < 4.2V Normal operation: -30C to +85C Restricted operation: -40C to +95C Physical RoHS LTE features 3GPP Release 13 HSPA features 3GPP Release 8 Dimensions: 40mm x 36mm x 3mm Weight: 8.8g All hardware components fully compliant with EU RoHS Directive Down- and Uplink carrier aggregation (CA) to increase bandwidth, and thereby increase bitrate:
Maximum aggregated bandwidth: 80MHz Maximum number of component carriers: 2 Inter-band FDD Intra-band FDD, TDD, contiguous, non-contiguous Supported inter- and intra-band CA configurations: See Section 1.2.2 CAT 6 supported DL 300Mbps, UL 50Mbps 2x2 MIMO in DL direction UE CAT. 14, 24 DC-HSPA+ DL 42Mbps HSUPA UL 5.76Mbps Compressed mode (CM) supported according to 3GPP TS25.212 ALAS5_HIO_v00.030a Confidential / Preliminary 2019-04-01 Cinterion ALAS5 Hardware Interface Overview 1.2 Key Features at a Glance 15 Page 9 of 50 Feature UMTS features Implementation 3GPP Release 8 PS data rate 384 kbps DL / 384 kbps UL TD-SCDMA features 3GPP Release 4 2.8 Mbps DL / 2.2Mbps UL GSM / GPRS / EGPRS features Data transfer EDGE E2 power class for 8 PSK GPRS:
Multislot Class 12 Mobile Station Class B Coding Scheme 1 4 EGPRS:
Multislot Class 12 Downlink coding schemes CS 1-4, MCS 1-9 Uplink coding schemes CS 1-4, MCS 1-9 NACC, extended UL TBF Mobile Station Class B SRB loopback and test mode B 8-bit, 11-bit RACH 1 phase/2 phase access procedures Link adaptation and IR SMS Point-to-point MT and MO, Cell broadcast, Text and PDU mode Software AT commands Hayes, 3GPP TS 27.007 and 27.005, and proprietary Gemalto M2M com-
mands Embedded Linux platform Embedded Linux with API (ARC, RIL). Memory space available for Linux applications is 4GB in the flash file sys-
tem, and 2GB RAM. SIM Application Toolkit SAT Release 99, letter classes b, c, e with BIP and RunAT support Firmware update Firmware update supported GNSS Features Protocol Modes General NMEA Standalone GNSS (GPS, GLONASS, Beidou, Galileo) Integrated gpsOne 9HT support (GPS, GLONASS, Beidou, Galileo) QZSS and SBAS support Power saving modes DC feed bridge and control of power supply for active antenna via GPIO ALAS5_HIO_v00.030a Confidential / Preliminary 2019-04-01 Cinterion ALAS5 Hardware Interface Overview 1.2 Key Features at a Glance 15 Page 10 of 50 Feature Interfaces Module interface Implementation Surface mount device with solderable connection pads (SMT application interface). Land grid array (LGA) technology ensures high solder joint reliability and provides the possibility to use an optional module mounting socket. For more information on how to integrate SMT modules see also [3]. This application note comprises chapters on module mounting and application layout issues as well as on additional SMT application development equip-
ment. 50. GSM/UMTS/LTE main antenna, LTE Diversity/MIMO antenna,
(active/passive) GNSS antenna USB 2.0 High Speed (480Mbit/s) device interface or USB 3.0 Super Speed (5Gbit/s) device interface 8-wire (plus GND line) interface unbalanced, asynchronous Fixed baud rates from 115,200 to 921,600bps Supports RTS0/CTS0 hardware flow control ASC0:
Linux controlled only:
ASC1:
ASC2:
2-wire, unbalanced asynchronous interface at RXD2 and TXD2 lines used for tracing and debugging purposes (optional) 4-wire, unbalanced asynchronous interface Fixed baud rates: 115,200bps to 921,60bps Supports RTS1/CTS1 hardware flow control 2 UICC interfaces (switchable) Supported chip cards: UICC/SIM/USIM 2.85V, 1.8V 1 I2C interface 2 digital interfaces (I2S) - first DAI reserved for future use Switch-on by hardware signal IGT Switch-off by AT command (AT^SMSO) or IGT (option) Automatic switch-off in case of critical temperature or voltage conditions Reset Orderly shutdown and reset by AT command Emergency-off Emergency-off by hardware signal EMERG_OFF SAIC (Single Antenna Interference Cancellation) / DARP (Downlink Advanced Receiver Performance) Rx Diversity (receiver type 3i - 64-QAM) / MIMO 15 I/O pins of the application interface programmable as GPIO. GPIO1 can be configured as dead reckoning synchronization signal. Programming can be done via AT commands. Emergency call handling
(not for -US variant) EU eCall 3GPP Release 10 compliant (modem) ERA compliant (modem and GNSS) ADC inputs Analog-to-Digital Converter with four unbalanced analog inputs for (exter-
nal) antenna diagnosis JTAG JTAG interface for debug purposes ALAS5_HIO_v00.030a Confidential / Preliminary 2019-04-01 Antenna USB Serial interface UICC interface I2C interface Audio Power on/off, Reset Power on/off Special Features Antenna GPIO Cinterion ALAS5 Hardware Interface Overview 1.2 Key Features at a Glance 15 Page 11 of 50 Feature eMMC PCIe Evaluation kit Implementation Linux controlled:
Embedded Multi-Media Card interface Linux controlled:
PCIe interface Evaluation module ALAS5 module soldered onto a dedicated PCB. ALAS5_HIO_v00.030a Confidential / Preliminary 2019-04-01 Cinterion ALAS5 Hardware Interface Overview 1.2 Key Features at a Glance 15 1.2.1 Supported Frequency Bands Page 12 of 50 The following table lists the supported frequency bands for each of the ALAS5 product variants mentioned in Section 1.1. Supported CA configurations can be found in Section 1.2.2. Table 1: Supported frequency bands for each product variant Band ALAS5-W ALAS5-AM GSM/GPRS/EDGE 850MHz 900MHz 1800MHz 1900MHz UMTS/HSPA Bd.I (2100MHz) Bd.II (1900MHz) Bd.III (1800MHz) Bd.IV (1700MHz) Bd.V (850MHz) Bd.VI (850MHz) Bd.VIII (900MHz) Bd.XIX (850MHz) TD-SCDMA Bd.34 (2000MHz) Bd.39 (1900MHz) LTE-FDD Bd.1 (2100MHz) Bd.2 (1900MHz) Bd.3 (1800MHz) Bd.4 (1700MHz) Bd.5 (850MHz) Bd.7 (2600MHz) Bd.8 (900MHz) Bd.12 (700MHz) Bd.13 (750MHz) Bd.18 (850MHz) Bd.19 (850MHz) Bd.20 (800MHz) Bd.26 (850MHz) Bd.28 (700MHz) x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x ALAS5_HIO_v00.030a Confidential / Preliminary 2019-04-01 Cinterion ALAS5 Hardware Interface Overview 1.2 Key Features at a Glance 15 Table 1: Supported frequency bands for each product variant Band ALAS5-W ALAS5-AM Page 13 of 50 x x x Bd.29 (700MHz)
<supplementary downlink>
Bd.30 (2300MHZ)
<supplementary downlink>
Bd.32 (1500MHz)
<supplementary downlink>
Bd.66 (1700MHz) LTE-TDD Bd.34 (2000MHz) Bd.38 (2600MHz) Bd.39 (1900MHz) Bd.40 (2300MHz) Bd.41 (2600MHz)1 x x x x x x 1. Note: Out of the 3GPP specified frequency range for LTE Band 41, only that part which is used in China and Japan (2545MHz to 2655MHz) is supported by ALAS5. 1.2.2 Supported CA Configurations The following table lists the supported CA configurations (aka supported band combinations) for each of the ALAS5 product variants mentioned in Section 1.1. Table 2: Supported CA configurations Downlink CA Intra-band continuous Bandwidth combination set Product variant
(ALAS5-...) 0, 1 0, 1 0 0 0 0 0 0, 1, 2 0, 1 0, 1, 2, 3 0, 1, 2 0, 1, 2, 3 0, 1 CA_1C CA_3C CA_5B CA_7B CA_7C CA_8B CA_38C CA_39C CA_40C CA_41C CA_3A-3A CA_7A-7A CA_40A-40A Intra-band non-continuous AM, W AM, W AM, W W W W W W W W W W AM, W ALAS5_HIO_v00.030a Confidential / Preliminary 2019-04-01 Cinterion ALAS5 Hardware Interface Overview 1.2 Key Features at a Glance 15 Page 14 of 50 Table 2: Supported CA configurations Downlink CA CA_41A-41A Inter-band (two bands) Bandwidth combination set Product variant
(ALAS5-...) CA_1A-5A CA_1A-8A CA_1A-18A CA_1A-19A CA_1A-20A CA_1A-26A CA_1A-28A CA_2A-13A CA_3A-5A CA_3A-8A CA_3A-19A CA_3A-20A CA_3A-26A CA_3A-28A CA_4A-13A CA_5A-7A CA_5A-40A CA_7A-8A CA_7A-20A CA_7A-28A CA_7B-28A CA_8A-40A CA_8A-41A CA_13A-66A CA_13A-66B CA_20A-38A CA_20A-40A CA_26A-41A CA_28A-40A CA_28A-41A 0, 1, 2, 3,4 0, 1, 2, 3 0, 1 0, 1 0, 1, 2 0, 1 0 0 0, 1 0, 1 0, 1 0 0, 1 0, 1 0, 1 0, 1 0, 1 0, 1 0, 1 0, 1 0 0, 1 0, 1 0 0 0 0 0 0 0, 1 0, 1, 2 AM W W W W W W W W W W W W W W W W W W W AM AM W W W W W AM AM, W AM, W AM, W ALAS5_HIO_v00.030a Confidential / Preliminary 2019-04-01 Cinterion ALAS5 Hardware Interface Overview 1.3 ALAS5 System Overview 15 1.3 ALAS5 System Overview GNSS ANT_MAIN ANT_DRX_MIMO Page 15 of 50 Power Supply Antenna-
diagnostic Antenna-
diagnostic Application SIM Card SIM Card GNSS GSM/UMTS/LTE GPIO 2 x ADC UICC USB 2.0/3.0 PCIe ASC0 ASC1 I2C GPIO eMMC IGT EMERG_OFF Power Supply ALAS5 2x Digital Audio B S U e I C P e c a f r e t n I l a i r e S e c a f r e t n I l a i r e S C 2 I S 2 I
M C P I O P G e c a f r e t n I C M M e Application Interfaces Application Figure 1: ALAS5 system overview T X E V D N I _ R W P Power Supply ALAS5_HIO_v00.030a Confidential / Preliminary 2019-04-01 Cinterion ALAS5 Hardware Interface Overview 2 Interface Characteristics 32 2 Interface Characteristics Page 16 of 50 ALAS5 is equipped with an SMT application interface that connects to the external application. The SMT application interface incorporates the various application interfaces as well as the RF antenna interface. 2.1 Application Interface 2.1.1 USB Interface ALAS5 supports a USB 3.0 Super Speed (5Gbps) device interface, and alternatively a USB 2.0 device interface that is High Speed compatible. The USB interface is primarily intended for use as command and data interface, and for downloading firmware. The USB host is responsible for supplying the VUSB_IN line. This line is for voltage detection only. The USB part (driver and transceiver) is supplied by means of BATT+. This is because ALAS5 is designed as a self-powered device compliant with the Universal Serial Bus Specifi-
cation Revision 3.01. SMT lin. reg. Module USB part a) 2.0 USB_HS _PHY USB 2.0 Controller 2.0 USB_SS _PHY USB 3.0 3.0 Controller 100nF 100nF VBUS Detection only 1F BATT+
GND c) USB_DP USB_DNc) USB_SSRX_N USB_SSRX_P USB_SSTX_N USB_SSTX_P c) c) c) c) VUSB_IN b) All serial (including R S) and pull -up resistors for data lines are implemented . Since VUSB_IN is used for detection only it is recommended not to add any further blocking capacitors on a) b) the VUSB_IN line. c) If the USB interface is operated with super or high speeds, it is recommended to take special care routing the data lines. Application layout should implement a differential impedance of 90 ohms for proper signal integrity . Figure 2: USB circuit To properly connect the module's USB interface to the external application, a USB 3.0 or 2.0 compatible connector and cable or hardware design is required. Furthermore, the USB modem driver distributed with ALAS5 needs to be installed. 1. The specification is ready for download on http://www.usb.org/developers/docs/
ALAS5_HIO_v00.030a Confidential / Preliminary 2019-04-01 Cinterion ALAS5 Hardware Interface Overview 2.1 Application Interface 32 2.1.2 Serial Interface ASC0 Page 17 of 50 ALAS5 offers an 8-wire (plus GND) unbalanced, asynchronous modem interface ASC0 con-
forming to ITU-T V.24 protocol DCE signaling. The electrical characteristics do not comply with ITU-T V.28. The significant levels are 0V (for low data bit or active state) and 1.8V (for high data bit or inactive state). ALAS5 is designed for use as a DCE. Based on the conventions for DCE-DTE connections it communicates with the customer application (DTE) using the following signals:
Port TXD @ application sends data to the modules TXD0 signal line Port RXD @ application receives data from the modules RXD0 signal line Figure 3: Serial interface ASC0 Features:
Includes the data lines TXD0 and RXD0, the status lines RTS0 and CTS0, and the modem control lines DTR0, DSR0, DCD0 and RING0. Configured for 8 data bits, no parity and 1 stop bit. ASC0 can be operated at fixed bit rates from 115,200 to 921,600bps. Supports RTS0/CTS0 hardware flow control. Note: If the ASC0 serial interface is the applications only interface, it is suggested to connect test points on the USB signal lines as a potential tracing possibility. ALAS5_HIO_v00.030a Confidential / Preliminary 2019-04-01 Cinterion ALAS5 Hardware Interface Overview 2.1 Application Interface 32 2.1.3 Serial Interface ASC1 Page 18 of 50 ALAS5 provides a 4-wire unbalanced, asynchronous modem interface ASC1 conforming to ITU-T V.24 protocol DCE signaling. The electrical characteristics do not comply with ITU-T V.28. The significant levels are 0V (for low data bit or active state) and 1.8V (for high data bit or inactive state). ALAS5 is designed for use as a DCE. Based on the conventions for DCE-DTE connections it communicates with the customer application (DTE) using the following signals:
Port TXD @ application sends data to modules TXD1 signal line Port RXD @ application receives data from the modules RXD1 signal line Figure 4: Serial interface ASC1 Features Includes only the data lines TXD1 and RXD1 plus RTS1 and CTS1 for hardware hand-
shake. On ASC1 no RING line is available. Configured for 8 data bits, no parity and 1 or 2 stop bits. ASC1 can be operated at fixed bit rates from 115,200 bps to 921,600 bps. Supports RTS1/CTS1 hardware flow. Linux controlled only. ALAS5_HIO_v00.030a Confidential / Preliminary 2019-04-01 Cinterion ALAS5 Hardware Interface Overview 2.1 Application Interface 32 2.1.4 Inter-Integrated Circuit Interface Page 19 of 50 ALAS5 provides an Inter-Integrated Circuit (I2C) interface. I2C is a serial, 8-bit oriented data transfer bus for bit rates up to 400kbps in Fast mode. It consists of two lines, the serial data line I2CDAT and the serial clock line I2CCLK. The module acts as a single master device, e.g. the clock I2CCLK is driven by the module. I2CDAT is a bi-directional line. Each device connected to the bus is software addressable by a unique 7-bit address, and simple master/slave relation-
ships exist at all times. The module operates as master-transmitter or as master-receiver. The customer application transmits or receives data only on request of the module. The applications I2C interface can be powered via the VEXT line of ALAS5. If connected to the VEXT line, the I2C interface will properly shut down when the module enters the Power Down mode. In the application I2CDAT and I2CCLK lines need to be connected to a positive supply voltage
(e.g., VEXT) via a pull-up resistor. Module VEXT I2CCLK I2CDAT GND Application p u l l u p R p u l l u p R I2CCLK I2CDAT GND Figure 5: I2C interface connected to VEXT Note: Good care should be taken when creating the PCB layout of the host application: The traces of I2CCLK and I2CDAT should be equal in length and as short as possible. ALAS5_HIO_v00.030a Confidential / Preliminary 2019-04-01 Cinterion ALAS5 Hardware Interface Overview 2.1 Application Interface 32 2.1.5 UICC/SIM/USIM Interface Page 20 of 50 ALAS5 has two UICC/SIM/USIM interfaces compatible with the 3GPP 31.102 and ETSI 102 221. These are wired to the host interface in order to be connected to an external SIM card holder. Five pads on the SMT application interface are reserved for each of the two SIM inter-
faces. The UICC/SIM/USIM interface supports 2.85V and 1.8V SIM cards. The CCINx signal serves to detect whether a tray (with SIM card) is present in the card holder. Using the CCINx signal is mandatory for compliance with the GSM 11.11 recommendation if the mechanical design of the host application allows the user to remove the SIM card during operation. To take advantage of this feature, an appropriate SIM card detect switch is required on the card holder. For example, this is true for the model supplied by Molex, which has been tested to operate with ALAS5 and is part of the Gemalto M2M reference equipment submitted for type approval. See Chapter 7 for Molex ordering numbers. Table 3: Signals of the SIM interface (SMT application interface) Signal Description Ground connection for SIM interfaces. Optionally a separate SIM ground line may be used to improve EMC. Chipcard clock line for 1st and 2nd SIM interface. SIM supply voltage line for 1st and 2nd SIM interface. Serial data line for 1st and 2nd SIM interface, input and output. Chipcard reset line for 1st and 2nd SIM interface. Input on the baseband processor for detecting a SIM card tray in the holder. If the SIM is removed during operation the SIM interface is shut down immediately to prevent destruc-
tion of the SIM. The CCINx signal is active low. The CCINx signal is mandatory for applications that allow the user to remove the SIM card during operation. The CCINx signal is solely intended for use with a SIM card. It must not be used for any other purposes. Failure to comply with this requirement may invalidate the type approval of ALAS5. Note: No guarantee can be given, nor any liability accepted, if loss of data is encountered after removing the SIM card during operation. Also, no guarantee can be given for properly initializ-
ing any SIM card that the user inserts after having removed the SIM card during operation. In this case, the application must restart ALAS5. GND CCCLK1 CCCLK2 CCVCC1 CCVCC2 CCIO1 CCIO2 CCRST1 CCRST2 CCIN1 CCIN2 ALAS5_HIO_v00.030a Confidential / Preliminary 2019-04-01 Cinterion ALAS5 Hardware Interface Overview 2.1 Application Interface 32 Page 21 of 50 Module CCCLK1 1n SIM /
UICC open: Card removed closed: Card inserted CCIN1 CCRST1 GND CCIO1 e c a f r e t n i n o i t a c i l p p a T M S CCVCC1 220n Figure 6: First UICC/SIM/USIM interface The total cable length between the SMT application interface pads on ALAS5 and the pads of the external SIM card holder must not exceed 100mm in order to meet the specifications of 3GPP TS 51.010-1 and to satisfy the requirements of EMC compliance. To avoid possible cross-talk from the CCCLKx signal to the CCIOx signal be careful that both lines are not placed closely next to each other. A useful approach is using the GND line to shield the CCIOx line from the CCCLKx line. Note: Figure 6 shows how to connect a SIM card holder to the first SIM interface. With the sec-
ond SIM interface some internally integrated components on the SIM circuit will have to be ex-
ternally integrated as shown for the second SIM interface in Figure 7. The external components at CCIN2 should be populated as close as possible to the signals SMT pad Module CCCLK2 e c a f r e t n i n o i t a c i l p p a T M S VEXT 22k CCIN2 Open: Card removed Closed: Card inserted 2k2 100pF CCRST2 1nF SIM /
UICC GND CCIO2 10k CCVCC2 220nF Figure 7: Second UICC/SIM/USIM interface ALAS5_HIO_v00.030a Confidential / Preliminary 2019-04-01 Cinterion ALAS5 Hardware Interface Overview 2.1 Application Interface 32 2.1.6 Digital Audio Interface Page 22 of 50 ALAS5 has two digital audio interfaces (DAIs) that can be employed as inter pulse code mod-
ulation (PCM) or Inter-IC Sound (I2S) interface. Default setting is pulse code modulation. Please note that the first DAI is reserved for future use. 2.1.6.1 Pulse Code Modulation Interface (PCM) ALAS5's PCM interface can be used to connect audio devices capable of pulse code modula-
tion. 2.1.6.2 Inter-IC Sound Interface The Inter-IC Sound Interface is a standardized bidirectional I2S based digital audio interface for transmission of mono voice signals for telephony services. The I2S properties and capabilities comply with the requirements layed out in the Phillips I2S Bus Specifications, revised June 5, 1996. 2.1.7 Analog-to-Digital Converter (ADC) ALAS5 provides four unbalanced ADC input lines: ADC[1-2...4-5]_IN. They can be used to measure four independent, externally connected DC voltages in the range of 0.1V to 1.7V. 2.1.8 GPIO Interface ALAS5 has 15 GPIOs for external hardware devices. Each GPIO can be configured for use as input or output. All settings are AT command controlled. 2.1.9 eMMC Interface ALAS5 has an eMMC interface that can be used for development and test purposes, e.g., to write crash dumps from the modules FFS to eMMC. ALAS5_HIO_v00.030a Confidential / Preliminary 2019-04-01 Cinterion ALAS5 Hardware Interface Overview 2.2 GSM/UMTS/LTE Antenna Interface 32 2.2 GSM/UMTS/LTE Antenna Interface Page 23 of 50 The ALAS5 GSM/UMTS/LTE antenna interface comprises a GSM/UMTS/LTEmain antenna as well as a UMTS/LTE Rx diversity/MIMO antenna to improve signal reliability and quality1. The interface has an impedance of 50. ALAS5 is capable of sustaining a total mismatch at the an-
tenna interface without any damage, even when transmitting at maximum RF power. The external antennas must be matched properly to achieve best performance regarding radi-
ated power, modulation accuracy and harmonic suppression. Matching networks are not in-
cluded on the ALAS5 PCB and should be placed in the host application, if the antenna does not have an impedance of 50. Regarding the return loss ALAS5 provides the following values in the active band:
Table 4: Return loss in the active band State of module Return loss of module Recommended return loss of application Receive Transmit
> 8dB Undefined mismatch
> 12dB
> 12dB 1. By delivery default the UMTS/LTE Rx diversity/MIMO antenna is configured as available for the module since its usage is mandatory for LTE. Please refer to [1] for details on how to configure antenna settings. ALAS5_HIO_v00.030a Confidential / Preliminary 2019-04-01 Cinterion ALAS5 Hardware Interface Overview 2.2 GSM/UMTS/LTE Antenna Interface 32 2.2.1 Antenna Installation Page 24 of 50 The antennas are connected by soldering the antenna pads (ANT_MAIN, ANT_DRX_MIMO, ANT_GNSS) and their neighboring ground pads directly to the applications PCB. The distance between the antenna pads and their neighboring GND pads has been optimized for best possible impedance. To prevent mismatch, special attention should be paid to these pads on the application PCB. To prevent receiver desensitization due to interferences generated by fast transients like high speed clocks on the external application PCB, it is recommended to realize the antenna con-
nection line using embedded Stripline rather than Micro-Stripline technology. For type approval purposes (i.e., FCC KDB 996369 related to modular approval requirements), an external application must connect the RF signal in one of the following ways:
Via 50 coaxial antenna connector (common connectors are U-FL or SMA) placed as close as possible to the module's antenna pad. By soldering the antenna to the antenna connection line on the applications PCB (without the use of any connector) as close as possible to the modules antenna pad. By routing the application PCBs antenna to the modules antenna pad in the shortest pos-
sible way. ALAS5_HIO_v00.030a Confidential / Preliminary 2019-04-01 Cinterion ALAS5 Hardware Interface Overview 2.2 GSM/UMTS/LTE Antenna Interface 32 2.2.2 RF Line Routing Design 2.2.2.1 Line Arrangement Instructions Page 25 of 50 Several dedicated tools are available to calculate line arrangements for specific applications and PCB materials - for example from http://www.polarinstruments.com/ (commercial software) or from http://web.awrcorp.com/Usa/Products/Optional-Products/TX-Line/ (free software). Embedded Stripline This below figure shows line arrangement examples for embedded stripline. Figure 8: Embedded Stripline line arrangement ALAS5_HIO_v00.030a Confidential / Preliminary 2019-04-01 Cinterion ALAS5 Hardware Interface Overview 2.2 GSM/UMTS/LTE Antenna Interface 32 Page 26 of 50 Micro-Stripline This section gives two line arrangement examples for micro-stripline. Figure 9: Micro-Stripline line arrangement samples ALAS5_HIO_v00.030a Confidential / Preliminary 2019-04-01 Cinterion ALAS5 Hardware Interface Overview 2.2 GSM/UMTS/LTE Antenna Interface 32 2.2.2.2 Routing Examples Page 27 of 50 Interface to RF Connector Figure 10 shows a sample connection of a modules antenna pad at the bottom layer of the module PCB with an application PCBs coaxial antenna connector. Line impedance depends on line width, but also on other PCB characteristics like dielectric, height and layer gap. The sample stripline width of 0.40mm is recommended for an application with a PCB layer stack resembling the one of the ALAS5 evaluation board. For different layer stacks the stripline width will have to follow stripline routing rules, avoiding 90 degree corners and using the shortest dis-
tance to the PCBs coaxial antenna connector. G N D G N D e.g. ANT_ MAIN Stripline (50 ohms) on top layer of evaluation board from antenna pad to module edge Width = 0.40 mm Ground connection Edge of module PCB 50 ohms microstrip line E.g., U.FL antenna connector G N D G N D Figure 10: Routing to applications RF connector ALAS5_HIO_v00.030a Confidential / Preliminary 2019-04-01 Cinterion ALAS5 Hardware Interface Overview 2.3 GNSS Antenna Interface 32 2.3 GNSS Antenna Interface Page 28 of 50 In addition to the RF antenna interface ALAS5 also has a GNSS antenna interface. The GNSS pads shape is the same as for the RF antenna interface (see Section 2.2.1). It is possible to connect active or passive GNSS antennas. In either case they must have 50 impedance. The simultaneous operation of GSM/UMTS/LTE and GNSS is implemented. ALAS5 provides the signal GNSS_EN to enable an active GNSS antenna power supply. Figure 11 shows the flexibility in realizing the power supply for an active GNSS antenna by giving a sample circuit realizing the supply voltage for an active GNSS antenna. Module Application:
GNSS Receiver Antenna Matching ANT_GNSS RF DC DC LNA Active GNSS Antenna ANT_GNSS_DC BATT+
VGNSS
(3.2V) GNSS_EN IN OUT LDO EN LP3985IM5-3.2 Rs Is 1R0 Rv 100
Io Current Sensor FAN4010 Io Rg 3k3 ADC5_IN Si1023X_1 10k 1u ESD Protection Si1023X_2 10k Ug Figure 11: Supply voltage for active GNSS antenna ALAS5_HIO_v00.030a Confidential / Preliminary 2019-04-01 Cinterion ALAS5 Hardware Interface Overview 2.3 GNSS Antenna Interface 32 Page 29 of 50 Figure 12 shows a sample circuit realizing ESD protection for a passive GNSS antenna. Con-
necting the input ANT_GNSS_DC to GND prevents ESD from coupling into the module. Module SMT interface GNSS _EN Not used 100nF ANT_GNSS _DC 10nH ANT_GNSS To GNSS receiver
(Optional) ESD protection 0R Passive GNSS antenna Figure 12: ESD protection for passive GNSS antenna ALAS5_HIO_v00.030a Confidential / Preliminary 2019-04-01 Cinterion ALAS5 Hardware Interface Overview 2.4 Sample Application 32 2.4 Sample Application Page 30 of 50 Figure 13 shows a typical example of how to integrate an ALAS5 module with an application. The PWR_IND line is an open collector that needs an external pull-up resistor which connects to the voltage supply VCC C of the microcontroller. Low state of the open collector pulls the PWR_IND signal low and indicates that the ALAS5 module is active, high level notifies the Power Down mode. If the module is in Power Down mode avoid current flowing from any other source into the mod-
ule circuit, for example reverse current from high state external control lines. Therefore, the controlling application must be designed to prevent reverse flow. While developing SMT applications it is strongly recommended to provide test points for certain signals, i.e., lines to and from the module - for debug and/or test purposes. The SMT application should allow for an easy access to these signals. For details on how to implement test points see [3]. The EMC measures are best practice recommendations. In fact, an adequate EMC strategy for an individual application is very much determined by the overall layout and, especially, the po-
sition of components. Some LGA pads are connected to clocks or high speed data streams that might interfere with the modules antenna. The RF receiver would then be blocked at certain frequencies (self in-
terference). The external applications PCB tracks connected to these pads should therefore be well shielded or kept away from the antenna. This applies especially to the USB and UICC/
SIM interfaces. Depending on the micro controller used by an external application ALAS5s digital input and output lines may require level conversion. Disclaimer:
No warranty, either stated or implied, is provided on the sample schematic diagram shown in Figure 13 and the information detailed in this section. As functionality and compliance with na-
tional regulations depend to a great amount on the used electronic components and the indi-
vidual application layout manufacturers are required to ensure adequate design and operating safeguards for their products using ALAS5 modules. ALAS5_HIO_v00.030a Confidential / Preliminary 2019-04-01 Cinterion ALAS5 Hardware Interface Overview 2.4 Sample Application 32 Page 31 of 50 47k 47k 100k VCC C VDD
(1.8V) VCC C IGT EMERG _OFF ANT_DRX_MIMO Main antenna
(GSM/UMTS/LTE) Diversity antenna
(LTE) ANT_MAIN GND GND GND GND PWR_IND VEXT (1.8V) BATT+
BATT+_RF 2 2 47F Ultra low ESR Rechargeable Lithium battery
NTC Module 4 x 47F Ultra low ESR OE VCCB VCCA 4 Level Controller PCM interface lines 4 PCM2_... USB 2.0 HS Mode Or Mode USB 3.0 SS 2 4 VUSB_IN USB_DP, USB_DN USB_SS... Optional low capacitance ESD protection**
CCIN CCVCC CCRST CCIO CCCLK GND SIM 220nF 1nF All SIM components should be close to card holder. Keep SIM wires low capacitive. Figure 13: ALAS5 sample application ALAS5_HIO_v00.030a Confidential / Preliminary 2019-04-01 Cinterion ALAS5 Hardware Interface Overview 3 GNSS Interface 32 3 GNSS Interface Page 32 of 50 ALAS5 integrates a GNSS receiver that offers the full performance of GPS/GLONASS technol-
ogy. The GNSS receiver is able to continuously track all satellites in view, thus providing accu-
rate satellite position data. The integrated GNSS receiver supports the NMEA protocol via USB or ASC0 interface. NMEA is a combined electrical and data specification for communication between various (marine) electronic devices including GNSS receivers. It has been defined and controlled by the US based National Marine Electronics Association. For more information on the NMEA Standard please refer to http://www.nmea.org. Depending on the receivers knowledge of last position, current time and ephemeris data, the receivers startup time (i.e., TTFF = Time-To-First-Fix) may vary: If the receiver has no knowl-
edge of its last position or time, a startup takes considerably longer than if the receiver has still knowledge of its last position, time and almanac or has still access to valid ephemeris data and the precise time. By default, the GNSS receiver is switched off. It has to be switched on and configured. Dead Reckoning Sync Line:
Dead reckoning solutions are used in (automotive) platforms to determine the (vehicles) loca-
tion even when there is no GPS signal available (e.g. in tunnels, basement garages or even between high buildings in cities). In addition to dead reckoning related NMEA sentences, ALAS5 provides a dead reckoning syn-
chronization line (DR_SYNC line) to be employed in external dead reckoning applications. DR_SYNC is derived from the GNSS signal clock as 1 pulse per second (1PPS) signal. The DR_SYNC signal is provided as long as synchronized with the GNSS satellite clock, and con-
tinues after GNSS signal loss. ALAS5_HIO_v00.030a Confidential / Preliminary 2019-04-01 Cinterion ALAS5 Hardware Interface Overview 4 Mechanical Dimensions and Mounting 34 Page 33 of 50 4 Mechanical Dimensions and Mounting 4.1 Mechanical Dimensions of ALAS5 Figure 14 shows a 3D view1 of ALAS5 and provides an overview of the board's mechanical di-
mensions2. For further details see Figure 15. Length:
Width:
Height:
40mm 36mm 3mm Top view Bottom view Figure 14: ALAS5 top and bottom view 1. The coloring of the 3D view does not reflect the modules real color. 2. Note: The holes in the shielding (top view) are significantly smaller than the radiated wavelength from the module. Gemalto guarantees that there will be no emissions outside the limits from these. The RF circuitry of the module is fully shielded. ALAS5_HIO_v00.030a Confidential / Preliminary 2019-04-01 Cinterion ALAS5 Hardware Interface Overview 4.1 Mechanical Dimensions of ALAS5 34
9 8
A B
3 1
0
Page 34 of 50
2
2
2
ALAS5_HIO_v00.030a Confidential / Preliminary 2019-04-01 Figure 15: Dimensions of ALAS5 (all dimensions in mm) Cinterion ALAS5 Hardware Interface Overview 5 Regulatory and Type Approval Information 42 Page 35 of 50 5 Regulatory and Type Approval Information 5.1 Directives and Standards ALAS5 has been designed to comply with the directives and standards listed below. It is the responsibility of the application manufacturer to ensure compliance of the final product with all provisions of the applicable directives and standards as well as with the technical spec-
ifications provided in the "ALAS5 Hardware Interface Description".1 Table 5: Directives 2014/53/EU 2002/95/EC (RoHS 1) 2011/65/EC (RoHS 2) 2015/863/EU (RoHS 3) Directive of the European Parliament and of the council of 16 April 2014 on the harmonization of the laws of the Member States relating to the making available on the market of radio equipment and repealing Directive 1999/
05/EC. The product is labeled with the CE conformity mark. Directive of the European Parliament and of the Council of 27 January 2003 on the restriction of the use of certain haz-
ardous substances in electrical and electronic equipment
(RoHS) Revised on 8 June 2011. Further revision on 31 March 2015 - amending Annex II to Directive 2011/65/EU of the European Parliament and of the Council as regards the list of restricted substances. Table 6: Standards of North American type approval CFR Title 47 Code of Federal Regulations, Part 22, Part 24, Part 27, and Part 90; US Equipment Authorization FCC OET Bulletin 65
(Edition 97-01) Evaluating Compliance with FCC Guidelines for Human Exposure to Radiofrequency Electromagnetic Fields UL 60 950-1 Product Safety Certification (Safety requirements) NAPRD.03 V5.35 Overview of PCS Type certification review board Mobile Equipment Type Certification and IMEI control PCS Type Certification Review board (PTCRB) RSS132, RSS133, RSS139 Canadian Standard 1. Manufacturers of applications which can be used in the US shall ensure that their applications have a PTCRB approval. For this purpose they can refer to the PTCRB approval of the respective module. ALAS5_HIO_v00.030a Confidential / Preliminary 2019-04-01 Cinterion ALAS5 Hardware Interface Overview 5.1 Directives and Standards 42 Table 7: Standards of European type approval Page 36 of 50 3GPP TS 51.010-1 Digital cellular telecommunications system (Release 7); Mobile Station
(MS) conformance specification;
ETSI EN 301 511 V12.5.1 Global System for Mobile communications (GSM); Mobile Stations (MS) equipment; Harmonized Standard covering the essential requirements of article 3.2 of Directive 2014/53/EU GCF-CC V3.70 Global Certification Forum - Certification Criteria ETSI EN 301 489-01 V2.1.1 Draft ETSI EN 301 489-52 V1.1.0 Electromagnetic Compatibility (EMC) standard for radio equipment and ser-
vices; Part 1: Common technical requirements; Harmonized Standard cov-
ering the essential requirements of article 3.1(b) of Directive 2014/53/EU and the essential requirements of article 6 of Directive 2014/30/EU Electromagnetic Compatibility (EMC) standard for radio equipment and ser-
vices; Part 52: Specific conditions for Cellular Communication Mobile and portable (UE) radio and ancillary equipment; Harmonized Standard cover-
ing the essential requirements of article 3.1(b) of Directive 2014/53/EU ETSI EN 301 908-01 V11.1.1 IMT cellular networks; Harmonized Standard covering the essential require-
ments of article 3.2 of the Directive 2014/53/EU; Part 1: Introduction and common requirements ETSI EN 301 908-02 V11.1.1 IMT cellular networks; Harmonized Standard covering the essential require-
ments of article 3.2 of the Directive 2014/53/EU; Part 2: CDMA Direct Spread (UTRA FDD) User Equipment (UE) ETSI EN 301 908-13 V11.1.1 IMT cellular networks; Harmonized Standard covering the essential require-
ments of article 3.2 of the Directive 2014/53/EU; Part 13: Evolved Universal Terrestrial Radio Access (E-UTRA) User Equipment (UE) EN 60950-1:2006/
A11:2009+A1:2010+A1 2:2011+A2:2013 Safety of information technology equipment Table 8: Requirements of quality IEC 60068 Environmental testing DIN EN 60529 IP codes ALAS5_HIO_v00.030a Confidential / Preliminary 2019-04-01 Cinterion ALAS5 Hardware Interface Overview 5.1 Directives and Standards 42 Page 37 of 50 Table 9: Standards of the Ministry of Information Industry of the Peoples Republic of China SJ/T 11363-2006 SJ/T 11364-2006 Requirements for Concentration Limits for Certain Hazardous Substances in Electronic Information Products (2006-06). Marking for Control of Pollution Caused by Electronic Information Products (2006-06). According to the Chinese Administration on the Control of Pollution caused by Electronic Information Products
(ACPEIP) the EPUP, i.e., Environmental Protection Use Period, of this product is 20 years as per the symbol shown here, unless otherwise marked. The EPUP is valid only as long as the product is operated within the operating limits described in the Hardware Interface Description. Please see Table 10 for an overview of toxic or hazardous substances or elements that might be contained in product parts in concentrations above the limits defined by SJ/T 11363-2006. Table 10: Toxic or hazardous substances or elements with defined concentration limits ALAS5_HIO_v00.030a Confidential / Preliminary 2019-04-01 Cinterion ALAS5 Hardware Interface Overview 5.2 SAR requirements specific to portable mobiles 42 Page 38 of 50 5.2 SAR requirements specific to portable mobiles Mobile phones, PDAs or other portable transmitters and receivers incorporating a GSM module must be in accordance with the guidelines for human exposure to radio frequency energy. This requires the Specific Absorption Rate (SAR) of portable ALAS5 based applications to be eval-
uated and approved for compliance with national and/or international regulations. Since the SAR value varies significantly with the individual product design manufacturers are advised to submit their product for approval if designed for portable use. For US and European markets the relevant directives are mentioned below. It is the responsibility of the manufacturer of the final product to verify whether or not further standards, recommendations or directives are in force outside these areas. Products intended for sale on US markets ES 59005/ANSI C95.1 Considerations for evaluation of human exposure to electromagnetic fields (EMFs) from mobile telecommunication equipment (MTE) in the frequency range 30MHz - 6GHz Products intended for sale on European markets EN 50360 EN 62311:2008 Product standard to demonstrate the compliance of mobile phones with the basic restrictions related to human exposure to electromagnetic fields (300MHz - 3GHz) Assessment of electronic and electrical equipment related to human exposure restrictions for electromagnetic fields (0 Hz - 300 GHz) IMPORTANT:
Manufacturers of portable applications based on ALAS5 modules are required to have their fi-
nal product certified and apply for their own FCC Grant and Industry Canada Certificate related to the specific portable mobile. ALAS5_HIO_v00.030a Confidential / Preliminary 2019-04-01 Cinterion ALAS5 Hardware Interface Overview 5.3 Reference Equipment for Type Approval 42 Page 39 of 50 5.3 Reference Equipment for Type Approval The Gemalto M2M general reference setup submitted to type approve ALAS5 is shown in the figure below: Figure 16 illustrates the setup for general tests and evaluation purposes. The evaluation module can be plugged directly onto the so-called Audio(-Ethernet) Adapter. The GSM/UMTS/LTE as well as the GNSS test equipment is connected via antennas at the SMA connectors on the evaluation module1. The PC is connected via USB interface on the evalua-
tion module, and the audio test equipment via audio jack on the Audio(-Ethernet) Adapter. A N T _ M A IN A NT _D RX _M IM O A LA S5 r o t i c a p a C k n a B S S N G i o d u A A udio T e s te quipm e nt 0
. 0 / 3
. 2 B S U PC T e s te quipm e nt 4 .0 V Pow e r Supply G N SS T e ste quipm e nt G SM /W CD M A /LT E T e ste quipm e nt Figure 16: Reference equipment for type approval Please note that for EMC and RF performance tests, slightly different reference equipment con-
figurations are used. If necessary, please contact Gemalto for further details. 1. The following antennas were used with the approval reference equipment:
- RF antennas: LPBEM-7-27 (for details see www.panorama-antennas.com)
- GNSS antenna: AA.162.301111 (for details see www.taoglas.com) ALAS5_HIO_v00.030a Confidential / Preliminary 2019-04-01 Cinterion ALAS5 Hardware Interface Overview 5.4 Compliance with FCC and ISED Rules and Regulations 42 Page 40 of 50 5.4 Compliance with FCC and ISED Rules and Regulations The Equipment Authorization Certification for the Gemalto M2M modules reference application described in Section 5.3 will be registered under the following identifiers:
ALAS5-W:
FCC Identifier QIPALAS5-W Granted to Gemalto M2M GmbH ALAS5-AM:
FCC Identifier QIPALAS5-AM ISED Certification Number: 7830A-ALAS5AM Granted to Gemalto M2M GmbH Note1: Manufacturers of mobile or fixed devices incorporating ALAS5-W/-AM modules are au-
thorized to use the FCC Grants and ISED Certificates of the ALAS5-W modules for their own final products according to the conditions referenced in these documents. In this case, the FCC label of the module shall be visible from the outside, or the host device shall bear a second label stating "Contains FCC ID: QIPALAS5-W"or "Contains FCC ID: QIPALAS5-AM", and accord-
ingly Contains IC: 7830A-ALAS5AM. The integration is limited to fixed or mobile categorized host devices, where a separation distance between the antenna and any person of min. 20cm can be assured during normal operating conditions. For mobile and fixed operation configurations the antenna gain, including cable loss, must not exceed the limits listed in the following Table 11 and Table 12 for FCC and/or ISED. Table 11: Antenna gain limits for FCC for ALAS5-W (TBD.) Maximum gain in operating band FCC limit 850MHz (GSM) 1900MHZ (GSM) Band V (UMTS) Band 5 (LTE-FDD) Band 7 (LTE-FDD) Band 26 (LTE-FDD) Unit dBi dBi dBi dBi dBi dBi 1. Label note in French for ISED: Les fabricants d'quipement mobile ou fixe intgrant le module ALAS66A-W/-US sont autoriss utiliser les accords FCC et certificats d'Innovation, Sciences et Dve-
loppement conomique Canada (ISED) du module ALAS5-W/-AM pour leur propre produit final suivant les conditions rfrences dans ces documents. Dans ce cas, le label FCC du module doit tre visible de l'extrieur, sinon l'quipement hte doit disposer d'un second label avec la dclaration suivante "
Contains FCC ID : QIPALALAS5-W ", ou " Contains FCC ID : QIPALALAS5-AM " et en consquence "
Contains IC : 7830A-ALAS5AM ". L'intgration est limite aux catgories d'quipement hte mobile ou fixe, respectant une distance minimum de 20 centimtres entre l'antenne et toute personne avoisinante pour des conditions d'utilisation normale. ALAS5_HIO_v00.030a Confidential / Preliminary 2019-04-01 Cinterion ALAS5 Hardware Interface Overview 5.4 Compliance with FCC and ISED Rules and Regulations 42 Page 41 of 50 Table 12: Antenna gain limits for FCC and ISED for ALAS5-AM (TBD.) Maximum gain in operating band FCC limit ISED limit Unit 850MHz (GSM) 1900MHZ (GSM) Band II (UMTS) Band IV (UMTS) Band V (UMTS) Band 2 (LTE-FDD) Band 4 (LTE-FDD) Band 5 (LTE-FDD) Band 7 (LTE-FDD) Band 12 (LTE-FDD) Band 13 (LTE-FDD) Band 66(LTE-FDD) dBi dBi dBi dBi dBi dBi dBi dBi dBi dBi dBi dBi IMPORTANT:
Manufacturers of portable applications incorporating ALAS5-W/-AM modules are required to have their final product certified and apply for their own FCC Grant and ISED Certificate related to the specific portable mobile. This is mandatory to meet the SAR requirements for portable mobiles (see Section 5.2 for detail). Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules and with ISED license-exempt RSS standard(s). These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interfer-
ence to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or televi-
sion reception, which can be determined by turning the equipment off and on, the user is en-
couraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Connect the equipment into an outlet on a circuit different from that to which the receiver Increase the separation between the equipment and receiver. is connected. Consult the dealer or an experienced radio/TV technician for help. This Class B digital apparatus complies with Canadian ICES-003. ALAS5_HIO_v00.030a Confidential / Preliminary 2019-04-01 Cinterion ALAS5 Hardware Interface Overview 5.4 Compliance with FCC and ISED Rules and Regulations 42 Page 42 of 50 If Canadian approval is requested for devices incorporating ALAS5 modules the above note will have to be provided in the English and French language in the final user documentation. Manufacturers/OEM Integrators must ensure that the final user documentation does not con-
tain any information on how to install or remove the module from the final product. Notes (ISED):
(EN) This Class B digital apparatus complies with Canadian ICES-003 and RSS-210. Opera-
tion is subject to the following two conditions: (1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired operation of the device.
(FR) Cet appareil numrique de classe B est conforme aux normes canadiennes ICES-003 et RSS-210. Son fonctionnement est soumis aux deux conditions suivantes: (1) cet appareil ne doit pas causer d'interfrence et (2) cet appareil doit accepter toute interfrence, notamment les interfrences qui peuvent affecter son fonctionnement.
(EN) Radio frequency (RF) Exposure Information The radiated output power of the Wireless Device is below the Industry Canada (IC) radio fre-
quency exposure limits. The Wireless Device should be used in such a manner such that the potential for human contact during normal operation is minimized. This device has also been evaluated and shown compliant with the IC RF Exposure limits un-
der mobile exposure conditions. (antennas are greater than 20cm from a persons body).
(FR) Informations concernant l'exposltion aux frquences radio (RF) La puissance de sortie mise par l'appareil de sans fiI est infrieure la limite d'exposition aux frquences radio dInnovation, Sciences et Dveloppement conomique Canada (ISDE). Utili-
sez l'appareil de sans fil de faon minimiser les contacts humains lors du fonctionnement nor-
mal. Ce priphrique a galement t valu et dmontr conforme aux limites d'exposition aux RF d'ISDE dans des conditions d'exposition des appareils mobiles (les antennes se situent moins de 20cm du corps d'une personne). ALAS5_HIO_v00.030a Confidential / Preliminary 2019-04-01 Cinterion ALAS5 Hardware Interface Overview 6 Document Information 47 6 Document Information Page 43 of 50 New document: "Cinterion ALAS5 Hardware Interface Overview" v00.030a 6.1 Revision History Chapter What is new
Initial document setup. ALAS5_HIO_v00.030a Confidential / Preliminary 2019-04-01 Page 44 of 50 Cinterion ALAS5 Hardware Interface Overview 6.2 Related Documents 47 6.2 Related Documents
[1] ALAS5 AT Command Set
[2] ALAS5 Release Note
[3] Application Note 48: SMT Module Integration
[4] Universal Serial Bus Specification Revision 3.0
[5] Universal Serial Bus Specification Revision 2.0 6.3 Terms and Abbreviations Abbreviation Description American National Standards Institute Antenna Reference Point Carrier Aggregation Conformit Europene (European Conformity) Coding Scheme Circuit Switched Circuit Switched Data Download Do not use Discontinuous Reception Development Support Board Discontinuous Transmission Enhanced Data rates for GSM Evolution Extended GSM Electromagnetic Compatibility Electrostatic Discharge European Telecommunication Standard European Telecommunications Standards Institute Federal Communications Commission (U.S.) Frequency Division Duplex General Packet Radio Service Global Standard for Mobile Communications High Speed Downlink Packet Access High Impedance Input/Output International Mobile Equipment Identity International Standards Organization ANSI ARP CA CE CS CS CSD DL dnu DRX DSB DTX EDGE EGSM EMC ESD ETS ETSI FCC FDD GPRS GSM HiZ HSDPA I/O IMEI ISO ALAS5_HIO_v00.030a Confidential / Preliminary 2019-04-01 Cinterion ALAS5 Hardware Interface Overview 6.3 Terms and Abbreviations 47 Abbreviation Description International Telecommunications Union Page 45 of 50 ITU kbps LED LGA LTE MBB Mbps MCS MIMO MLCC eMMC MO MS MSL MT nc NTC PCB PCIe PCL PD PDU PS PSK PU QAM RF rfu ROPR RTC Rx SAR SELV SIM SMD kbits per second Light Emitting Diode Land Grid Array Long term evolution Moisture barrier bag Mbits per second Modulation and Coding Scheme Multiple Input Multiple Output Multi Layer Ceramic Capacitor Embedded MultiMediaCard Mobile Originated Mobile Station, also referred to as TE Moisture Sensitivity Level Mobile Terminated Not connected Negative Temperature Coefficient Printed Circuit Board Peripheral Component Interconnect Express Power Control Level Pull Down resistor Protocol Data Unit Packet Switched Phase Shift Keying Pull Up resistor Radio Frequency Reserved for future use Radio Output Power Reduction Real Time Clock Receive Direction Specific Absorption Rate Safety Extra Low Voltage Subscriber Identification Module Surface Mount Device Quadrature Amplitude Modulation R&TTE Radio and Telecommunication Terminal Equipment ALAS5_HIO_v00.030a Confidential / Preliminary 2019-04-01 Cinterion ALAS5 Hardware Interface Overview 6.3 Terms and Abbreviations 47 Page 46 of 50 Abbreviation Description SMS SMT SRAM SRB TE TPC TS Tx UL UMTS URC USB UICC USIM Short Message Service Surface Mount Technology Static Random Access Memory Signalling Radio Bearer Terminal Equipment Transmit Power Control Technical Specification Transmit Direction Upload Unsolicited Result Code Universal Serial Bus USIM Integrated Circuit Card Universal Mobile Telecommunications System UMTS Subscriber Identification Module WCDMA Wideband Code Division Multiple Access ALAS5_HIO_v00.030a Confidential / Preliminary 2019-04-01 Cinterion ALAS5 Hardware Interface Overview 6.4 Safety Precaution Notes 47 6.4 Safety Precaution Notes Page 47 of 50 The following safety precautions must be observed during all phases of the operation, usage, service or repair of any cellular terminal or mobile incorporating ALAS5. Manufacturers of the cellular terminal are advised to convey the following safety information to users and operating personnel and to incorporate these guidelines into all manuals supplied with the product. Fail-
ure to comply with these precautions violates safety standards of design, manufacture and in-
tended use of the product. Gemalto M2M assumes no liability for customers failure to comply with these precautions. When in a hospital or other health care facility, observe the restrictions on the use of mobiles. Switch the cellular terminal or mobile off, if instructed to do so by the guide-
lines posted in sensitive areas. Medical equipment may be sensitive to RF energy. The operation of cardiac pacemakers, other implanted medical equipment and hear-
ing aids can be affected by interference from cellular terminals or mobiles placed close to the device. If in doubt about potential danger, contact the physician or the manufac-
turer of the device to verify that the equipment is properly shielded. Pacemaker patients are advised to keep their hand-held mobile away from the pacemaker, while it is on. Switch off the cellular terminal or mobile before boarding an aircraft. Make sure it can-
not be switched on inadvertently. The operation of wireless appliances in an aircraft is forbidden to prevent interference with communications systems. Failure to observe these instructions may lead to the suspension or denial of cellular services to the offender, legal action, or both. Do not operate the cellular terminal or mobile in the presence of flammable gases or fumes. Switch off the cellular terminal when you are near petrol stations, fuel depots, chemical plants or where blasting operations are in progress. Operation of any elec-
trical equipment in potentially explosive atmospheres can constitute a safety hazard. Your cellular terminal or mobile receives and transmits radio frequency energy while switched on. Remember that interference can occur if it is used close to TV sets, radios, computers or inadequately shielded equipment. Follow any special regulations and always switch off the cellular terminal or mobile wherever forbidden, or when you suspect that it may cause interference or danger. IMPORTANT!
Cellular terminals or mobiles operate using radio signals and cellular networks. Because of this, connection cannot be guaranteed at all times under all conditions. Therefore, you should never rely solely upon any wireless device for essential com-
munications, for example emergency calls. Remember, in order to make or receive calls, the cellular terminal or mobile must be switched on and in a service area with adequate cellular signal strength. Some networks do not allow for emergency calls if certain network services or phone features are in use (e.g. lock functions, fixed dialing etc.). You may need to deactivate those features before you can make an emergency call. Some networks require that a valid SIM card be properly inserted in the cellular termi-
nal or mobile. ALAS5_HIO_v00.030a Confidential / Preliminary 2019-04-01 Cinterion ALAS5 Hardware Interface Overview 7 Appendix 49 Page 48 of 50 7 Appendix 7.1 List of Parts and Accessories Table 13: List of parts and accessories Description ALAS5 Supplier Ordering information Gemalto M2M Standard module ALAS5 Evaluation module Gemalto M2M Ordering number:
Votronic Handset Votronic ordering number: HH-SI-30.3/V1.1/0 VOTRONIC /
Gemalto M2M Gemalto M2M IMEI:
Packaging unit (ordering) number:
L30960-N5950-A100 (ALAS5-W) L30960-N5940-A100 (ALAS5-AM) Module label number:
L30960-N5950-A100-11 (ALAS5-W) L30960-N5940-A100-11 (ALAS5-AM) L30960-N5951-A100 (ALAS5-W) L30960-N5941-A100 (ALAS5-AM) Votronic Entwicklungs- und Produktionsgesellschaft fr elek-
tronische Gerte mbH Saarbrcker Str. 8 66386 St. Ingbert Germany Phone: +49-(0)6 89 4 / 92 55-0 Fax: +49-(0)6 89 4 / 92 55-88 Email: contact@votronic.com Ordering numbers: 91228 91236 Sales contacts are listed in Table 14. Sales contacts are listed in Table 14 and Table 15. SIM card holder incl. push button ejector and slide-in tray U.FL antenna connector Molex Molex or Hirose 1. Note: At the discretion of Gemalto M2M, module label information can either be laser engraved on the modules shielding or be printed on a label adhered to the modules shielding. ALAS5_HIO_v00.030a Confidential / Preliminary 2019-04-01 Cinterion ALAS5 Hardware Interface Overview 7.1 List of Parts and Accessories 49 Page 49 of 50 Table 14: Molex sales contacts (subject to change) Molex For further information please click:
http://www.molex.com Molex China Distributors Beijing, Room 1311, Tower B, COFCO Plaza No. 8, Jian Guo Men Nei Street, 100005 Beijing P.R. China Phone: +86-10-6526-9628 Fax: +86-10-6526-9730 Molex Deutschland GmbH Otto-Hahn-Str. 1b 69190 Walldorf Germany Phone: +49-6227-3091-0 Fax: +49-6227-3091-8100 Email: mxgermany@molex.com Molex Singapore Pte. Ltd. 110, International Road Jurong Town, Singapore 629174 American Headquarters Lisle, Illinois 60532 U.S.A. Phone: +1-800-78MOLEX Fax: +1-630-969-1352 Molex Japan Co. Ltd. 1-5-4 Fukami-Higashi, Yamato-City, Kanagawa, 242-8585 Japan Phone: +65-6-268-6868 Fax: +65-6-265-6044 Phone: +81-46-265-2325 Fax: +81-46-265-2365 Table 15: Hirose sales contacts (subject to change) Hirose Ltd. For further information please click:
http://www.hirose.com Hirose Electric (U.S.A.) Inc 2688 Westhills Court Simi Valley, CA 93065 U.S.A. Phone: +1-805-522-7958 Fax: +1-805-522-3217 Hirose Electric Europe B.V. UK Branch:
First Floor, St. Andrews House, Caldecotte Lake Business Park, Milton Keynes MK7 8LE Great Britain Hirose Electric Co., Ltd. 5-23, Osaki 5 Chome, Shinagawa-Ku Tokyo 141 Japan Hirose Electric Europe B.V. German Branch:
Herzog-Carl-Strasse 4 73760 Ostfildern Germany Phone: +49-711-456002-1 Fax: +49-711-456002-299 Email: info@hirose.de Hirose Electric Europe B.V. Hogehillweg 8 1101 CC Amsterdam Z-O Netherlands Phone: +44-1908-369060 Fax: +44-1908-369078 Phone: +81-03-3491-9741 Fax: +81-03-3493-2933 Phone: +31-20-6557-460 Fax: +31-20-6557-469 ALAS5_HIO_v00.030a Confidential / Preliminary 2019-04-01 About Gemalto Since 1996, Gemalto has been pioneering groundbreaking M2M and IoT products that keep our customers on the leading edge of innovation. We work closely with global mobile network operators to ensure that Cinterion modules evolve in sync with wireless networks, providing a seamless migration path to protect your IoT technology investment. Cinterion products integrate seamlessly with Gemalto identity modules, security solutions and licensing and monetization solutions, to streamline development timelines and provide cost efficiencies that improve the bottom line. As an experienced software provider, we help customers manage connectivity, security and quality of service for the long lifecycle of IoT solutions. For more information please visit www.gemalto.com/m2m, www.facebook.com/gemalto, or Follow@gemaltoIoT on Twitter. 50 Gemalto M2M GmbH Werinherstrasse 81 81541 Munich Germany GEMALTO.COM/M2M
. s e i r t n u o c i n a t r e c n i i d e r e t s g e r e r a d n a o t l a m e G f o s k r a m e c v r e s i d n a s k r a m e d a r t e r a
, o g o l o t l a m e G e h t
, o t l a m e G
. d e v r e s e r s t h g i r l l A
. 9 1 0 2 o t l a m e G
frequency | equipment class | purpose | ||
---|---|---|---|---|
1 | 2019-08-22 | 777 ~ 787 | PCB - PCS Licensed Transmitter | Original Equipment |
app s | Applicant Information | |||||
---|---|---|---|---|---|---|
1 | Effective |
2019-08-22
|
||||
1 | Applicant's complete, legal business name |
Gemalto M2M GmbH
|
||||
1 | FCC Registration Number (FRN) |
0007412448
|
||||
1 | Physical Address |
Siemensdamm 50
|
||||
1 |
Berlin, N/A
|
|||||
1 |
Germany
|
|||||
app s | TCB Information | |||||
1 | TCB Application Email Address |
a******@dekra.com
|
||||
1 | TCB Scope |
B1: Commercial mobile radio services equipment in the following 47 CFR Parts 20, 22 (cellular), 24,25 (below 3 GHz) & 27
|
||||
app s | FCC ID | |||||
1 | Grantee Code |
QIP
|
||||
1 | Equipment Product Code |
ALAS5-AM
|
||||
app s | Person at the applicant's address to receive grant or for contact | |||||
1 | Name |
A******** H****
|
||||
1 | Title |
Manager Certifications
|
||||
1 | Telephone Number |
00493********
|
||||
1 | Fax Number |
00493********
|
||||
1 |
a******@gemalto.com
|
|||||
app s | Technical Contact | |||||
n/a | ||||||
app s | Non Technical Contact | |||||
n/a | ||||||
app s | Confidentiality (long or short term) | |||||
1 | Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
1 | Long-Term Confidentiality Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
1 | If so, specify the short-term confidentiality release date (MM/DD/YYYY format) | 02/17/2020 | ||||
if no date is supplied, the release date will be set to 45 calendar days past the date of grant. | ||||||
app s | Cognitive Radio & Software Defined Radio, Class, etc | |||||
1 | Is this application for software defined/cognitive radio authorization? | No | ||||
1 | Equipment Class | PCB - PCS Licensed Transmitter | ||||
1 | Description of product as it is marketed: (NOTE: This text will appear below the equipment class on the grant) | Cinterion ALAS5-AM | ||||
1 | Related OET KnowledgeDataBase Inquiry: Is there a KDB inquiry associated with this application? | No | ||||
1 | Modular Equipment Type | Single Modular Approval | ||||
1 | Purpose / Application is for | Original Equipment | ||||
1 | Composite Equipment: Is the equipment in this application a composite device subject to an additional equipment authorization? | No | ||||
1 | Related Equipment: Is the equipment in this application part of a system that operates with, or is marketed with, another device that requires an equipment authorization? | No | ||||
1 | Grant Comments | Output power listed is conducted. Single Modular approval. This grant is valid only when the module is sold to OEM integrators. The module antenna(s) must be installed to meet the RF exposure compliance separation distance of 20 cm and any additional testing and authorization process as required. The module grantee is responsible for providing the documentation to the system integrator on restrictions of use, for continuing compliance of the module. The host integrator must follow the integration instructions provided by the module manufacturer and ensure that the composite-system end product complies with the FCC requirements by a technical assessment or evaluation to the FCC rules and to KDB Publication 996369. The host integrator installing this module into their product must ensure that the final composite product complies with the FCC requirements by a technical assessment or evaluation to the FCC rules, including the transmitter operation and should refer to guidance in KDB 996369. Installation of this device into specific final products may require the submission of a Class II permissive change application containing data pertinent to RF Exposure, emissions and host/module authentication, or new application if appropriate. The maximum antenna gain including cable loss for compliance with radiated power limits, RF exposure requirements and the categorical exclusion requirements of 2.1091 is 0.1 dBi for 850 MHz bands, 1.0 dBi for the 1900 MHz bands, 8 dBi for the 2500 MHz bands 4.0 dBi for 1700 MHz band and 5.6 dBi for 700 MHz bands. Multi-transmitter configurations, supporting simultaneous transmission, have not been evaluated and shall be evaluated according to KDB Publication 447498 and §2.947(f) composite system and §2.1 end product terms and concepts. Compliance of this device in all final product configurations is the responsibility of the Grantee. | ||||
1 | Is there an equipment authorization waiver associated with this application? | No | ||||
1 | If there is an equipment authorization waiver associated with this application, has the associated waiver been approved and all information uploaded? | No | ||||
app s | Test Firm Name and Contact Information | |||||
1 | Firm Name |
DEKRA Certification, Inc.
|
||||
1 | Name |
J****** F********
|
||||
1 | Telephone Number |
703 6********
|
||||
1 |
j******@dekra.com
|
|||||
Equipment Specifications | |||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
1 | 1 | 24E | 1850 | 1910 | 0.20989 | 0.1 ppm | 17M9G7W | ||||||||||||||||||||||||||||||||||
1 | 2 | 24E | 1850 | 1910 | 0.19634 | 0.1 ppm | 17M8D7W | ||||||||||||||||||||||||||||||||||
1 | 3 | 24E | 1850 | 1910 | 0.92045 | 0.1 ppm | 245KF9W | ||||||||||||||||||||||||||||||||||
1 | 4 | 24E | 1850 | 1910 | 0.37931 | 0.1 ppm | 245KF9W | ||||||||||||||||||||||||||||||||||
1 | 5 | 24E | 1850 | 1910 | 0.27861 | 0.1 ppm | 4M15G7W | ||||||||||||||||||||||||||||||||||
1 | 6 | 24E | 1850 | 1910 | 0.22387 | 0.1 ppm | 4M15G7W | ||||||||||||||||||||||||||||||||||
1 | 7 | 27 | 1710 | 1755 | 0.20227 | 0.1 ppm | 17M9G7W | ||||||||||||||||||||||||||||||||||
1 | 8 | 27 | 1710 | 1755 | 0.20277 | 0.1 ppm | 17M9D7W | ||||||||||||||||||||||||||||||||||
1 | 9 | 27 | 1710 | 1755 | 0.27225 | 0.1 ppm | 4M15G7W | ||||||||||||||||||||||||||||||||||
1 | 1 | 27 | 1710 | 1755 | 0.17783 | 0.1 ppm | 4M15G7W | ||||||||||||||||||||||||||||||||||
1 | 11 | 22H | 824 | 849 | 0.20845 | 0.1 ppm | 9M02G7W | ||||||||||||||||||||||||||||||||||
1 | 12 | 22H | 824 | 849 | 0.20845 | 0.1 ppm | 8M98D7W | ||||||||||||||||||||||||||||||||||
1 | 13 | 22H | 824 | 849 | 1.7298 | 0.1 ppm | 245KF9W | ||||||||||||||||||||||||||||||||||
1 | 14 | 22H | 824 | 849 | 0.43551 | 0.1 ppm | 245KF9W | ||||||||||||||||||||||||||||||||||
1 | 15 | 22H | 824 | 849 | 0.27606 | 0.1 ppm | 4M15G7W | ||||||||||||||||||||||||||||||||||
1 | 16 | 22H | 824 | 849 | 0.23442 | 0.1 ppm | 4M15G7W | ||||||||||||||||||||||||||||||||||
1 | 17 | 27 | 2500 | 2570 | 0.2133 | 0.1 ppm | 17M8G7W | ||||||||||||||||||||||||||||||||||
1 | 18 | 27 | 2500 | 2570 | 0.18967 | 0.1 ppm | 17M9D7W | ||||||||||||||||||||||||||||||||||
1 | 19 | 27 | 699 | 716 | 0.21928 | 0.1 ppm | 9M08G7W | ||||||||||||||||||||||||||||||||||
1 | 2 | 27 | 699 | 716 | 0.21928 | 0.1 ppm | 9M06D7W | ||||||||||||||||||||||||||||||||||
1 | 21 | 27 | 777 | 787 | 0.20797 | 0.1 ppm | 8M96G7W | ||||||||||||||||||||||||||||||||||
1 | 22 | 27 | 777 | 787 | 0.17947 | 0.1 ppm | 8M98G7W |
some individual PII (Personally Identifiable Information) available on the public forms may be redacted, original source may include additional details
This product uses the FCC Data API but is not endorsed or certified by the FCC