all | frequencies |
|
exhibits | applications |
---|---|---|---|---|
manual |
app s | submitted / available | |||||||
---|---|---|---|---|---|---|---|---|
1 2 |
|
user manual | Users Manual | 1.20 MiB | ||||
1 2 | Cover Letter(s) | |||||||
1 2 | RF Exposure Info | July 11 2011 | ||||||
1 2 | Cover Letter(s) | |||||||
1 2 | Cover Letter(s) | |||||||
1 2 | Test Report | |||||||
1 2 | Test Report | |||||||
1 2 | Test Report | |||||||
1 2 | Test Report | |||||||
1 2 | Test Setup Photos | |||||||
1 2 | External Photos | |||||||
1 2 | Internal Photos | |||||||
1 2 | ID Label/Location Info | |||||||
1 2 | Cover Letter(s) | July 11 2011 | ||||||
1 2 | Test Report |
1 2 | user manual | Users Manual | 1.20 MiB |
PH8/PH8-P Version:
DocId:
02.000 PH8_PH8-P_HD_v02.000 i w e v r e v O e c a f r e n t I e r a w d r a H PH8/PH8-P Hardware Interface Overview 2 Document Name:
Version:
Date:
DocId:
Status PH8/PH8-P Hardware Interface Overview 02.000 2011-10-21 PH8_PH8-P_HD_v02.000 Confidential / Released GENERAL NOTE THE USE OF THE PRODUCT INCLUDING THE SOFTWARE AND DOCUMENTATION (THE "PROD-
UCT") IS SUBJECT TO THE RELEASE NOTE PROVIDED TOGETHER WITH PRODUCT. IN ANY EVENT THE PROVISIONS OF THE RELEASE NOTE SHALL PREVAIL. THIS DOCUMENT CON-
TAINS INFORMATION ON CINTERION PRODUCTS. THE SPECIFICATIONS IN THIS DOCUMENT ARE SUBJECT TO CHANGE AT CINTERION'S DISCRETION. CINTERION WIRELESS MODULES GMBH GRANTS A NON-EXCLUSIVE RIGHT TO USE THE PRODUCT. THE RECIPIENT SHALL NOT TRANSFER, COPY, MODIFY, TRANSLATE, REVERSE ENGINEER, CREATE DERIVATIVE WORKS;
DISASSEMBLE OR DECOMPILE THE PRODUCT OR OTHERWISE USE THE PRODUCT EXCEPT AS SPECIFICALLY AUTHORIZED. THE PRODUCT AND THIS DOCUMENT ARE PROVIDED ON AN
"AS IS" BASIS ONLY AND MAY CONTAIN DEFICIENCIES OR INADEQUACIES. TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, CINTERION WIRELESS MODULES GMBH DIS-
CLAIMS ALL WARRANTIES AND LIABILITIES. THE RECIPIENT UNDERTAKES FOR AN UNLIMITED PERIOD OF TIME TO OBSERVE SECRECY REGARDING ANY INFORMATION AND DATA PRO-
VIDED TO HIM IN THE CONTEXT OF THE DELIVERY OF THE PRODUCT. THIS GENERAL NOTE SHALL BE GOVERNED AND CONSTRUED ACCORDING TO GERMAN LAW. Copyright Transmittal, reproduction, dissemination and/or editing of this document as well as utilization of its con-
tents and communication thereof to others without express authorization are prohibited. Offenders will be held liable for payment of damages. All rights created by patent grant or registration of a utility model or design patent are reserved. Copyright 2011, Cinterion Wireless Modules GmbH Trademark Notice Microsoft and Windows are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries. All other registered trademarks or trademarks mentioned in this document are property of their respective owners. PH8_PH8-P_HD_v02.000 Confidential / Released Page 2 of 46 2011-10-21 PH8/PH8-P Hardware Interface Overview Contents 46 Contents 1 Introduction ................................................................................................................. 6 Related Documents ........................................................................................... 6 1.1 Terms and Abbreviations ................................................................................... 6 1.2 Regulatory and Type Approval Information ....................................................... 9 1.3 1.3.1 Directives and Standards...................................................................... 9 SAR requirements specific to portable mobiles .................................. 12 1.3.2 SELV Requirements ........................................................................... 13 1.3.3 1.3.4 Safety Precautions.............................................................................. 13 Product Concept ....................................................................................................... 15 2.1 Key Features at a Glance ................................................................................ 15 2.2 PH8/PH8-P System Overview ......................................................................... 18 Application Interface................................................................................................. 19 Operating Modes ............................................................................................. 20 3.1 3.2 Power Supply................................................................................................... 21 USB Interface................................................................................................... 22 3.3 Serial Interface ASC0 ...................................................................................... 23 3.4 3.5 UICC/SIM/USIM Interface................................................................................ 25 Analog Audio Interface..................................................................................... 27 3.6 3.7 Digital Audio Interface...................................................................................... 27 GPS Receiver............................................................................................................. 28 Antenna Interfaces.................................................................................................... 29 GSM/UMTS Antenna Interface ........................................................................ 29 5.1 5.1.1 Antenna Installation ............................................................................ 29 5.1.2 Antenna Connector ............................................................................. 30 5.2 GPS Antenna Interface .................................................................................... 34 Mechanics.................................................................................................................. 35 Mechanical Dimensions of PH8/PH8-P ........................................................... 35 6.1 Mounting PH8/PH8-P to the Application Platform............................................ 37 6.2 6.3 Board-to-Board Application Connector ............................................................ 37 Sample Application................................................................................................... 41 Reference Approval .................................................................................................. 43 8.1 Reference Equipment for Type Approval......................................................... 43 8.2 Compliance with FCC and IC Rules and Regulations ..................................... 44 Appendix.................................................................................................................... 45 9.1 List of Parts and Accessories........................................................................... 45 2 3 4 5 6 7 8 9 PH8_PH8-P_HD_v02.000 Confidential / Released Page 3 of 46 2011-10-21 PH8/PH8-P Hardware Interface Overview Tables 46 Tables Table 1:
Table 2:
Table 3:
Table 4:
Table 5:
Table 6:
Table 7:
Table 8:
Table 9:
Table 10:
Table 11:
Table 12:
Table 13:
Table 14:
Table 15:
Table 16:
Table 17:
Directives ......................................................................................................... 9 Standards of North American type approval .................................................... 9 Standards of European type approval.............................................................. 9 Requirements of quality ................................................................................. 10 Standards of the Ministry of Information Industry of the Peoples Republic of China............................................................................ 10 Toxic or hazardous substances or elements with defined concentration limits............................................................................................................... 11 Overview of operating modes ........................................................................ 20 DCE-DTE wiring of ASC0 .............................................................................. 24 Signals of the SIM interface (board-to-board connector) ............................... 25 Return loss in the active band........................................................................ 29 Product specifications of PH8/PH8-P antenna connectors............................ 30 Material and finish of PH8/PH8-P antenna connectors and recommended plugs .............................................................................................................. 31 Ordering information for Hirose U.FL Series.................................................. 33 Technical specifications of Molex board-to-board connector......................... 38 List of parts and accessories.......................................................................... 45 Molex sales contacts (subject to change) ...................................................... 46 Hirose sales contacts (subject to change) ..................................................... 46 PH8_PH8-P_HD_v02.000 Confidential / Released Page 4 of 46 2011-10-21 PH8/PH8-P Hardware Interface Overview Figures 46 Figures Figure 1:
Figure 2:
Figure 3:
Figure 4:
Figure 5:
Figure 6:
Figure 7:
Figure 8:
Figure 9:
Figure 10:
Figure 11:
Figure 12:
Figure 13:
Figure 14:
Figure 15:
PH8/PH8-P system overview......................................................................... 18 USB circuit ..................................................................................................... 22 Serial interface ASC0..................................................................................... 23 UICC/SIM/USIM interface .............................................................................. 26 Mechanical dimensions of PH8/PH8-P antenna connectors.......................... 30 U.FL-R-SMT connector with U.FL-LP-040 plug ............................................. 31 U.FL-R-SMT connector with U.FL-LP-066 plug ............................................. 31 Specifications of U.FL-LP-(V)-040(01) plug ................................................... 32 PH8/PH8-P top and bottom view ................................................................ 35 Dimensions of PH8/PH8-P (all dimensions in mm)........................................ 36 Mating board-to-board connector 53748-0808 on application ....................... 38 Molex board-to-board connector 52991-0808 on PH8/PH8-P ....................... 39 Mating board-to-board connector 53748-0808 on application ....................... 40 PH8/PH8-P sample application...................................................................... 42 Reference equipment for type approval......................................................... 43 PH8_PH8-P_HD_v02.000 Confidential / Released Page 5 of 46 2011-10-21 PH8/PH8-P Hardware Interface Overview 1 Introduction 14 1 Introduction The document1 describes the hardware of the PH8/PH8-P module, designed to connect to a cellular device application and the air interface. It helps you quickly retrieve interface specifica-
tions, electrical and mechanical details and information on the requirements to be considered for integrating further components. 1.1 Related Documents
[1] PH8/PH8-P AT Command Set
[2] PH8/PH8-P Release Notes
[3] DSB75 Support Box - Evaluation Kit for Cinterion Wireless Modules 1.2 Terms and Abbreviations Abbreviation AGPS ANSI AMR ARP B2B BB BEP BTS CB or CBM CE CS CS CSD CTM DAC DCS DL DRX DSB Description Assisted GPS American National Standards Institute Adaptive Multirate Antenna Reference Point Board-to-board connector Baseband Bit Error Probability Base Transceiver Station Cell Broadcast Message Conformit Europene (European Conformity) Coding Scheme Circuit Switched Circuit Switched Data Cellular Text Modem Digital-to-Analog Converter Digital Cellular System Download Discontinuous Reception Development Support Board 1. The document is effective only if listed in the appropriate Release Notes as part of the technical documentation delivered with your Cinterion Wireless Modules product. PH8_PH8-P_HD_v02.000 Confidential / Released Page 6 of 46 2011-10-21 PH8/PH8-P Hardware Interface Overview 1.2 Terms and Abbreviations 14 Abbreviation DSP DTMF DTX EDGE EFR EGSM EMC ERP ESD ETS ETSI FCC FDD FDMA FR GPRS GPS GSM HiZ HSDPA HR I/O IF IMEI ISO ITU kbps LED Mbps MCS MO MS MT NMEA NTC PBCCH Description Digital Signal Processor Dual Tone Multi Frequency Discontinuous Transmission Enhanced Data rates for GSM Evolution Enhanced Full Rate Extended GSM Electromagnetic Compatibility Effective Radiated Power Electrostatic Discharge European Telecommunication Standard European Telecommunications Standards Institute Federal Communications Commission (U.S.) Frequency Division Duplex Frequency Division Multiple Access Full Rate General Packet Radio Service Global Positioning System Global Standard for Mobile Communications High Impedance High Speed Downlink Packet Access Half Rate Input/Output Intermediate Frequency International Mobile Equipment Identity International Standards Organization International Telecommunications Union kbits per second Light Emitting Diode Mbits per second Modulation and Coding Scheme Mobile Originated Mobile Station, also referred to as TE Mobile Terminated National Marine Electronics Association Negative Temperature Coefficient Packet Switched Broadcast Control Channel PH8_PH8-P_HD_v02.000 Confidential / Released Page 7 of 46 2011-10-21 PH8/PH8-P Hardware Interface Overview 1.2 Terms and Abbreviations 14 Abbreviation PCB PCL PCM PCS PDU PS PSK QAM R&TTE RF ROPR RTC Rx SAR SELV SIM SLIC SMPL SMS SNR SRAM SRB SUPL TDMA TE TPC TS TTFF Tx UL UMTS URC USB UICC USIM WCDMA Description Printed Circuit Board Power Control Level Pulse Code Modulation Personal Communication System, also referred to as GSM 1900 Protocol Data Unit Packet Switched Phase Shift Keying Quadrature Amplitude Modulation Radio and Telecommunication Terminal Equipment Radio Frequency Radio Output Power Reduction Real Time Clock Receive Direction Specific Absorption Rate Safety Extra Low Voltage Subscriber Identification Module Subscriber Line Interface Circuit Sudden Momentary Power Loss Short Message Service Signal-to-Noise Ratio Static Random Access Memory Signalling Radio Bearer Secure User Plane Location Time Division Multiple Access Terminal Equipment Transmit Power Control Technical Specification Time To First Fix Transmit Direction Upload Universal Mobile Telecommunications System Unsolicited Result Code Universal Serial Bus USIM Integrated Circuit Card UMTS Subscriber Identification Module Wideband Code Division Multiple Access PH8_PH8-P_HD_v02.000 Confidential / Released Page 8 of 46 2011-10-21 PH8/PH8-P Hardware Interface Overview 1.3 Regulatory and Type Approval Information 14 1.3 Regulatory and Type Approval Information 1.3.1 Directives and Standards PH8/PH8-P has been designed to comply with the directives and standards listed below. It is the responsibility of the application manufacturer to ensure compliance of the final product with all provisions of the applicable directives and standards as well as with the technical spec-
ifications provided in the "PH8/PH8-P Hardware Interface Description".1 Table 1: Directives 99/05/EC 2002/95/EC Directive of the European Parliament and of the council of 9 March 1999 on radio equipment and telecommunications terminal equipment and the mutual recognition of their conformity (in short referred to as R&TTE Direc-
tive 1999/5/EC). The product is labeled with the CE conformity mark Directive of the European Parliament and of the Council of 27 January 2003 on the restriction of the use of certain haz-
ardous substances in electrical and electronic equipment
(RoHS) Table 2: Standards of North American type approval CFR Title 47 Code of Federal Regulations, Part 22, Part 24 and Part 27; US Equipment Authorization FCC Evaluating Compliance with FCC Guidelines for Human Exposure to Radio-
frequency Electromagnetic Fields Product Safety Certification (Safety requirements) Overview of PCS Type certification review board Mobile Equipment Type Certification and IMEI control PCS Type Certification Review board (PTCRB) Canadian Standard OET Bulletin 65
(Edition 97-01) UL 60 950-1 NAPRD.03 V5.8 RSS132, RSS133, RSS139 Table 3: Standards of European type approval 3GPP TS 51.010-1 Digital cellular telecommunications system (Release 7); Mobile Station
(MS) conformance specification;
ETSI EN 301 511 V9.0.2 Global System for Mobile communications (GSM); Harmonized standard for GCF-CC V3.43.1 ETSI EN 301 489-01 V1.8.1 mobile stations in the GSM 900 and DCS 1800 bands covering essential requirements under article 3.2 of the R&TTE directive (1999/5/EC) Global Certification Forum - Certification Criteria Electromagnetic Compatibility and Radio spectrum Matters (ERM); Electro-
magnetic Compatibility (EMC) standard for radio equipment and services;
Part 1: Common Technical Requirements 1. Manufacturers of applications which can be used in the US shall ensure that their applications have a PTCRB approval. For this purpose they can refer to the PTCRB approval of the respective module. PH8_PH8-P_HD_v02.000 Confidential / Released Page 9 of 46 2011-10-21 PH8/PH8-P Hardware Interface Overview 1.3 Regulatory and Type Approval Information 14 Table 3: Standards of European type approval ETSI EN 301 489-03 V1.4.1 Electromagnetic Compatibility and Radio spectrum Matters (ERM); Electro-
magnetic Compatibility (EMC) standard for radio equipment and services;
Part 3: Specific conditions for Short-Range Devices (SRD) operating on fre-
quencies between 9 kHz and 40 GHz Electromagnetic Compatibility and Radio spectrum Matters (ERM); Electro-
magnetic Compatibility (EMC) standard for radio equipment and services;
Part 7: Specific conditions for mobile and portable radio and ancillary equip-
ment of digital cellular radio telecommunications systems (GSM and DCS) Electromagnetic Compatibility and Radio spectrum Matters (ERM); Electro-
magnetic Compatibility (EMC) standard for radio equipment and services;
Part 24: Specific conditions for IMT-2000 CDMA Direct Spread (UTRA) for Mobile and portable (UE) radio and ancillary equipment Electromagnetic compatibility and Radio spectrum Matters (ERM); Base Stations (BS) and User Equipment (UE) for IMT-2000 Third Generation cel-
lular networks; Part 1: Harmonized EN for IMT-2000, introduction and com-
mon requirements of article 3.2 of the R&TTE Directive Electromagnetic compatibility and Radio spectrum Matters (ERM); Base Stations (BS) and User Equipment (UE) for IMT-2000 Third Generation cel-
lular networks; Part 2: Harmonized EN for IMT-2000, CDMA Direct Spread
(UTRA FDD) (UE) covering essential requirements of article 3.2 of the R&TTE Directive Electromagnetic compatibility and Radio spectrum Matters (ERM); Short range devices; Radio equipment to be used in the 1 GHz to 40 GHz fre-
quency range; Part 2: Harmonized EN covering essential requirements of article 3.2 of the R&TTE Directive Assessment of electronic and electrical equipment related to human expo-
sure restrictions for electromagnetic fields (0 Hz - 300 GHz) Safety of information technology equipment ETSI EN 301 489-07 V1.3.1 ETSI EN 301 489-24 V1.4.1 EN 301 908-01 V3.2.1 EN 301 908-02 V3.2.1 EN 300 440-02 V1.3.1 EN 62311:2008 IEC/EN 60950-1:2006 Table 4: Requirements of quality IEC 60068 DIN EN 60529 Environmental testing IP codes Table 5: Standards of the Ministry of Information Industry of the Peoples Republic of China SJ/T 11363-2006 Requirements for Concentration Limits for Certain Hazardous Substances in Electronic Information Products (2006-06). Marking for Control of Pollution Caused by Electronic Information Products (2006-06). SJ/T 11364-2006 According to the Chinese Administration on the Control of Pollution caused by Electronic Information Products
(ACPEIP) the EPUP, i.e., Environmental Protection Use Period, of this product is 20 years as per the symbol shown here, unless otherwise marked. The EPUP is valid only as long as the product is operated within the operating limits described in the Cinterion Hardware Interface Description. Please see Table 6 for an overview of toxic or hazardous substances or ele-
ments that might be contained in product parts in concentrations above the limits defined by SJ/T 11363-2006. PH8_PH8-P_HD_v02.000 Confidential / Released Page 10 of 46 2011-10-21 PH8/PH8-P Hardware Interface Overview 1.3 Regulatory and Type Approval Information 14 Table 6: Toxic or hazardous substances or elements with defined concentration limits PH8_PH8-P_HD_v02.000 Confidential / Released Page 11 of 46 2011-10-21 PH8/PH8-P Hardware Interface Overview 1.3 Regulatory and Type Approval Information 14 1.3.2 SAR requirements specific to portable mobiles Mobile phones, PDAs or other portable transmitters and receivers incorporating a GSM module must be in accordance with the guidelines for human exposure to radio frequency energy. This requires the Specific Absorption Rate (SAR) of portable PH8/PH8-P based applications to be evaluated and approved for compliance with national and/or international regulations. Since the SAR value varies significantly with the individual product design manufacturers are advised to submit their product for approval if designed for portable use. For European and US-
markets the relevant directives are mentioned below. It is the responsibility of the manufacturer of the final product to verify whether or not further standards, recommendations or directives are in force outside these areas. Products intended for sale on US markets ES 59005/ANSI C95.1 Considerations for evaluation of human exposure to electromagnetic fields (EMFs) from mobile telecommunication equipment (MTE) in the frequency range 30MHz - 6GHz Products intended for sale on European markets EN 50360 Product standard to demonstrate the compliance of mobile phones with the basic restrictions related to human exposure to electromagnetic fields (300MHz - 3GHz) IMPORTANT:
Manufacturers of portable applications based on PH8/PH8-P modules are required to have their final product certified and apply for their own FCC Grant and Industry Canada Certificate related to the specific portable mobile. PH8_PH8-P_HD_v02.000 Confidential / Released Page 12 of 46 2011-10-21 PH8/PH8-P Hardware Interface Overview 1.3 Regulatory and Type Approval Information 14 1.3.3 SELV Requirements The power supply connected to the PH8/PH8-P module shall be in compliance with the SELV requirements defined in EN 60950-1. 1.3.4 Safety Precautions The following safety precautions must be observed during all phases of the operation, usage, service or repair of any cellular terminal or mobile incorporating PH8/PH8-P. Manufacturers of the cellular terminal are advised to convey the following safety information to users and oper-
ating personnel and to incorporate these guidelines into all manuals supplied with the product. Failure to comply with these precautions violates safety standards of design, manufacture and intended use of the product. Cinterion Wireless Modules assumes no liability for customers failure to comply with these precautions. When in a hospital or other health care facility, observe the restrictions on the use of mobiles. Switch the cellular terminal or mobile off, if instructed to do so by the guide-
lines posted in sensitive areas. Medical equipment may be sensitive to RF energy. The operation of cardiac pacemakers, other implanted medical equipment and hearing aids can be affected by interference from cellular terminals or mobiles placed close to the device. If in doubt about potential danger, contact the physician or the manufac-
turer of the device to verify that the equipment is properly shielded. Pacemaker patients are advised to keep their hand-held mobile away from the pacemaker, while it is on. Switch off the cellular terminal or mobile before boarding an aircraft. Make sure it can-
not be switched on inadvertently. The operation of wireless appliances in an aircraft is forbidden to prevent interference with communications systems. Failure to observe these instructions may lead to the suspension or denial of cellular services to the offender, legal action, or both. Do not operate the cellular terminal or mobile in the presence of flammable gases or fumes. Switch off the cellular terminal when you are near petrol stations, fuel depots, chemical plants or where blasting operations are in progress. Operation of any electri-
cal equipment in potentially explosive atmospheres can constitute a safety hazard. Your cellular terminal or mobile receives and transmits radio frequency energy while switched on. Remember that interference can occur if it is used close to TV sets, radios, computers or inadequately shielded equipment. Follow any special regulations and always switch off the cellular terminal or mobile wherever forbidden, or when you suspect that it may cause interference or danger. Road safety comes first! Do not use a hand-held cellular terminal or mobile when driv-
ing a vehicle, unless it is securely mounted in a holder for speakerphone operation. Before making a call with a hand-held terminal or mobile, park the vehicle. Speakerphones must be installed by qualified personnel. Faulty installation or opera-
tion can constitute a safety hazard. PH8_PH8-P_HD_v02.000 Confidential / Released Page 13 of 46 2011-10-21 PH8/PH8-P Hardware Interface Overview 1.3 Regulatory and Type Approval Information 14 IMPORTANT!
Cellular terminals or mobiles operate using radio signals and cellular networks. Because of this, connection cannot be guaranteed at all times under all conditions. Therefore, you should never rely solely upon any wireless device for essential com-
munications, for example emergency calls. Remember, in order to make or receive calls, the cellular terminal or mobile must be switched on and in a service area with adequate cellular signal strength. Some networks do not allow for emergency calls if certain network services or phone features are in use (e.g. lock functions, fixed dialing etc.). You may need to deactivate those features before you can make an emergency call. Some networks require that a valid SIM card be properly inserted in the cellular termi-
nal or mobile. Bear in mind that exposure to excessive levels of noise can cause physical damage to users! With regard to acoustic shock, the cellular application must be designed to avoid unintentional increase of amplification, e.g. for a highly sensitive earpiece. A pro-
tection circuit should be implemented in the cellular application. PH8_PH8-P_HD_v02.000 Confidential / Released Page 14 of 46 2011-10-21 PH8/PH8-P Hardware Interface Overview 2 Product Concept 18 2 2.1 Product Concept Key Features at a Glance Feature General Frequency bands Implementation GSM/GPRS/EDGE: Quad band, 850/900/1800/1900MHz UMTS/HSPA+:
PH8: Five band, 800/850/AWS1/1900/2100MHz PH8-P: Five band, 800/850/9002/1900/2100MHz GSM class Small MS Output power (according to Release 99) Class 4 (+33dBm 2dB) for EGSM850 Class 4 (+33dBm 2dB) for EGSM900 Class 1 (+30dBm 2dB) for GSM1800 Class 1 (+30dBm 2dB) for GSM1900 Class E2 (+27dBm 3dB) for GSM 850 8-PSK Class E2 (+27dBm 3dB) for GSM 900 8-PSK Class E2 (+26dBm +3 /-4dB) for GSM 1800 8-PSK Class E2 (+26dBm +3 /-4dB) for GSM 1900 8-PSK Class 3 (+24dBm +1/-3dB) for UMTS 2100, WCDMA FDD BdI Class 3 (+24dBm +1/-3dB) for UMTS 1900,WCDMA FDD BdII Class 3 (+24dBm +1/-3dB) for UMTS AWS, WCDMA FDD BdIV1 Class 3 (+24dBm +1/-3dB) for UMTS 900, WCDMA FDD BdVIII2 Class 3 (+24dBm +1/-3dB) for UMTS 850, WCDMA FDD BdV Class 3 (+24dBm +1/-3dB) for UMTS 800, WCDMA FDD BdVI Power supply 3.3V < VBATT+ < 4.2V Operating temperature
(board temperature) Normal operation: -30C to +85C Restricted operation: -40C to +95C Physical RoHS HSPA features 3GPP Release 6, 7 UMTS features 3GPP Release 4 Dimensions: 33.9mm x 50mm x 3.1mm Weight: approx. 9.5g All hardware components fully compliant with EU RoHS Directive DL 14.4Mbps, UL 5.7Mbps UE CAT. 1-12 supported Compressed mode (CM) supported according to 3GPP TS25.212 PS data rate 384 kbps DL / 384 kbps UL CS data rate 64 kbps DL / 64 kbps UL PH8_PH8-P_HD_v02.000 Confidential / Released Page 15 of 46 2011-10-21 PH8/PH8-P Hardware Interface Overview 2.1 Key Features at a Glance 18 Feature GSM / GPRS / EGPRS features Data transfer Implementation Full PBCCH support EDGE E2 power class for 8 PSK GPRS:
Multislot Class 12 Mobile Station Class B Coding Scheme 1 4 EGPRS:
Multislot Class 12 Downlink coding schemes CS 1-4, MCS 1-9 Uplink coding schemes CS 1-4, MCS 1-9 NACC, extended UL TBF Mobile Station Class B CSD:
USSD Point-to-point MT and MO Cell broadcast Text and PDU mode SRB loopback and test mode B 8-bit, 11-bit RACH PBCCH support 1 phase/2 phase access procedures Link adaptation and IR V.110, RLP, non-transparent 14.4kbps SMS GPS Features Protocol Modes General Software AT commands SIM Application Toolkit Audio Firmware update Interfaces Module interface Antenna NMEA Standalone GPS Assisted GPS
- Control plane - E911
- User plane - gpsOneXTRA Power saving modes Power supply for active GPS antenna supported Hayes, 3GPP TS 27.007 and 27.005, and proprietary Cinterion Wireless Modules commands SAT Release 99 Audio speech codecs GSM: AMR, EFR, FR, HR 3GPP: AMR Speakerphone operation, echo cancellation, noise suppression, 9 ringing tones, TTY support Generic update from host application over ASC0 or USB 80-pin board-to-board connector 50Ohms. Main GSM/UMTS antenna, UMTS diversity antenna, GPS antenna (active/passive) PH8_PH8-P_HD_v02.000 Confidential / Released Page 16 of 46 2011-10-21 PH8/PH8-P Hardware Interface Overview 2.1 Key Features at a Glance 18 Feature USB Serial interface UICC interface Status Audio Power on/off, Reset Power on/off Reset Implementation USB 2.0 High Speed (480Mbit/s) device interface, Full Speed (12Mbit/s) compliant ASC0:
8-wire modem interface with status and control lines, unbalanced, asynchronous Adjustable baud rates from 9,600bps up to 921,600bps Supports RTS0/CTS0 hardware flow control Multiplex ability according to GSM 07.10 Multiplexer Protocol Supported chip cards: UICC/SIM/USIM 3V, 1.8V Signal line to indicate network connectivity state 1 analog interface with microphone feeding 1 digital interface: PCM or I2S Switch-on by hardware signal IGT Switch-off by AT command (AT^SMSO) Automatic switch-off in case of critical temperature or voltage conditions Orderly shutdown and reset by AT command Emergency-off Emergency-off by hardware signal EMERG_OFF if IGT is not active Special Features Phonebook TTY/CTM support Antenna Evaluation kit DSB75 SIM and phone Integrated CTM modem SAIC (Single Antenna Interference Cancellation) / DARP (Downlink Advanced Receiver Performance) Rx diversity (receiver type 3i - 16-QAM)3 DSB75 Evaluation Board designed to test and type approve Cinterion Wireless Modules and provide a sample configuration for application engineering. A special adapter is required to connect the module to the DSB75. 1. AWS UMTS/HSPA+ band IV supported by PH8 only. 2. 900MHz UMTS/HSPA+ band VIII supported by PH8-P only. Band VIII however, is not supported by the UMTS Rx diversity antenna. 3. UMTS Rx diversity antenna does not support UMTS/HSPA+ band VIII. PH8_PH8-P_HD_v02.000 Confidential / Released Page 17 of 46 2011-10-21 PH8/PH8-P Hardware Interface Overview 2.2 PH8/PH8-P System Overview 18 2.2 PH8/PH8-P System Overview GPS antenna GSM/UMTS antenna UMTS diversity antenna GPS GSM/UMTS Module USB Serial ASC0 UICC Analog audio Digital audio Power supply RTC IGT, Emergency Off Net state/
status e c a f r e t n i m e d o M SIM card Host application PCM or I2S codec
) T X E V
) D N I _ R W P
i n o i t a c d n i r e w o P n o i t a c i l p p a r o f r e w o P or Application On/Off Figure 1: PH8/PH8-P system overview PH8_PH8-P_HD_v02.000 Confidential / Released Page 18 of 46 2011-10-21 PH8/PH8-P Hardware Interface Overview 3 Application Interface 28 3 Application Interface PH8/PH8-P is equipped with an 80-pin board-to-board connector that connects to the external application. The host interface incorporates several sub-interfaces described in the following sections:
Operating modes - see Section 3.1 Power supply - see Section 3.2 Serial interface USB - see Section 3.3 Serial interface ASC0 - Section 3.4 UICC/SIM/USIM interface - see Section 3.5 Analog audio interface - see Section 3.6 Digital audio interface (PCM or I2S) - see Section 3.7 PH8_PH8-P_HD_v02.000 Confidential / Released Page 19 of 46 2011-10-21 PH8/PH8-P Hardware Interface Overview 3.1 Operating Modes 28 3.1 Operating Modes The table below briefly summarizes the various operating modes referred to in the following chapters. Table 7: Overview of operating modes Mode Normal operation Function GSM /
GPRS / UMTS /
HSPA SLEEP GSM /
GPRS / UMTS /
HSPA IDLE GSM TALK/
GSM DATA Power saving set automatically when no call is in progress and the USB connection is suspended by host or not present and no active commu-
nication via ASC0. Power saving disabled (see [1]: AT^SCFG "MEopMode/
PwrSave",<PwrSaveMode>) or an USB connection not suspended, but no call in progress. Connection between two subscribers is in progress. Power consump-
tion depends on the GSM network coverage and several connection settings (e.g. DTX off/on, FR/EFR/HR, hopping sequences and antenna connection). The following applies when power is to be mea-
sured in TALK_GSM mode: DTX off, FR and no frequency hopping. GPRS data transfer in progress. Power consumption depends on net-
work settings (e.g. power control level), uplink / downlink data rates and GPRS configuration (e.g. used multislot settings). EGPRS data transfer in progress. Power consumption depends on net-
work settings (e.g. power control level), uplink / downlink data rates and EGPRS configuration (e.g. used multislot settings). UMTS data transfer in progress. Power consumption depends on net-
work settings (e.g. TPC Pattern) and data transfer rate. HSPA data transfer in progress. Power consumption depends on net-
work settings (e.g. TPC Pattern) and data transfer rate. GPRS DATA EGPRS DATA UMTS TALK/
UMTS DATA HSPA DATA Power Down Airplane mode Normal shutdown after sending the AT^SMSO command. Only a voltage regulator is active for powering the RTC. Software is not active. Interfaces are not accessible. Operating volt-
age (connected to BATT+) remains applied. Airplane mode shuts down the radio part of the module, causes the module to log off from the GSM/GPRS network and disables all AT commands whose execution requires a radio connection. Airplane mode can be controlled by AT command (see [1]). PH8_PH8-P_HD_v02.000 Confidential / Released Page 20 of 46 2011-10-21 PH8/PH8-P Hardware Interface Overview 3.2 Power Supply 28 3.2 Power Supply PH8/PH8-P needs to be connected to a power supply at the board-to-board connector - 5 lines each BATT+ and GND. The power supply of PH8/PH8-P has to be a single voltage source at BATT+. It must be able to provide the peak current during the uplink transmission. All key functions for supplying power to the device are handled by the power management IC. It provides the following features:
Stabilizes the supply voltages for the baseband using switching regulators and low drop lin-
ear voltage regulators. Switches the module's power voltages for the power-up and -down procedures. Delivers, across the VEXT line, a regulated voltage for an external application. This voltage is not available in Power-down mode and can be reduced via AT command to save power. SIM switch to provide SIM power supply. PH8_PH8-P_HD_v02.000 Confidential / Released Page 21 of 46 2011-10-21 PH8/PH8-P Hardware Interface Overview 3.3 USB Interface 28 3.3 USB Interface PH8/PH8-P supports a USB 2.0 High Speed (480Mbit/s) device interface that is Full Speed
(12Mbit/s) compliant. The USB interface is primarily intended for use as command and data interface and for downloading firmware. The USB host is responsible for supplying the VUSB_IN line. This line is for voltage detection only. The USB part (driver and transceiver) is supplied by means of BATT+. This is because PH8/PH8-P is designed as a self-powered device compliant with the Universal Serial Bus Specification Revision 2.01. Module VREG (3V075) lin. reg. B2B USB part1) VBUS DP DN Detection only Host wakeup BATT+
GND VUSB_IN USB_DP2) USB_DN2) RING0 WAKEUP 1) All serial and pull-up resistors for data lines are implemented. 2) If the USB interface is operated in High Speed mode (480MHz), it is recommended to take special care routing the data lines USB_DP and USB_DN. Application layout should in this case implement a differential impedance of 90Ohm for proper signal integrity. Figure 2: USB circuit To properly connect the module's USB interface to the host a USB 2.0 compatible connector is required. Furthermore, the USB modem driver distributed with PH8/PH8-P needs to be in-
stalled. While the USB connection is active, the module will not change into SLEEP Mode. To enable switching into SLEEP mode the USB host must bring its USB interface into Suspend state (see Universal Serial Bus Specification Revision 2.01 for a description of the Suspend state). On incoming calls PH8/PH8-P will then generate a remote wake up request to resume the USB connection (active low). If configured for SDPORT=6, i.e., if using a CDC ACM compatible USB driver on the host system, a selective suspend on the USB host may not be supported and the module may therefore not be able to change into SLEEP mode. As an alternative to the regular USB remote wakeup mechanism it is possible to employ the RING0 or WAKEUP line to wake up the host application. The benefit is that the RING0 or WAKEUP lines can wake up the host application in case of incoming calls or other events sig-
nalized by URCs while the USB interface is suspended or shut down. 1. The specification is ready for download on http://www.usb.org/developers/docs/
PH8_PH8-P_HD_v02.000 Confidential / Released Page 22 of 46 2011-10-21 PH8/PH8-P Hardware Interface Overview 3.4 Serial Interface ASC0 28 3.4 Serial Interface ASC0 PH8/PH8-P offers an 8-wire unbalanced, asynchronous modem interface ASC0 conforming to ITU-T V.24 protocol DCE signalling. The electrical characteristics do not comply with ITU-T V.28. The significant levels are 0V (for low data bit or active state) and 1.8V (for high data bit or inactive state). PH8/PH8-P is designed for use as a DCE. Based on the conventions for DCE-DTE connections it communicates with the customer application (DTE) using the following signals:
Port TXD @ application sends data to the modules TXD0 signal line Port RXD @ application receives data from the modules RXD0 signal line Figure 3: Serial interface ASC0 Features:
Includes the data lines TXD0 and RXD0, the status lines RTS0 and CTS0 and, in addition, the modem control lines DTR0, DSR0, DCD0 and RING0. ASC0 is designed for controlling GSM/UMTS voice calls, transferring data and for control-
ling the module with AT commands. Full multiplexing capability allows the interface to be partitioned into virtual channels. The RING0 signal serves to indicate incoming calls and other types of URCs (Unsolicited Result Code). It can also be used to send pulses to the host application, for example to wake up the application from power saving state. See [1] for details on how to configure the RING0 line by AT^SCFG. Configured for 8 data bits, no parity and 1 stop bit. ASC0 can be operated at fixed bit rates from 9600bps up to 921600bps. Supports RTS0/CTS0 hardware flow control. Wake up from SLEEP mode by RTS0 activation (high to low transition). Note. If the ASC0 serial interface is the applications only interface, it is suggested to connect test points on the USB signal lines as a potential tracing possibility. PH8_PH8-P_HD_v02.000 Confidential / Released Page 23 of 46 2011-10-21 PH8/PH8-P Hardware Interface Overview 3.4 Serial Interface ASC0 28 Table 8: DCE-DTE wiring of ASC0 V.24 circuit DCE 103 104 105 106 108/2 107 109 125 Line function TXD0 RXD0 RTS0 CTS0 DTR0 DSR0 DCD0 RING0 Signal direction Input Output Input Output Input Output Output Output DTE Line function TXD RXD RTS CTS DTR DSR DCD RING Signal direction Output Input Output Input Output Input Input Input PH8_PH8-P_HD_v02.000 Confidential / Released Page 24 of 46 2011-10-21 PH8/PH8-P Hardware Interface Overview 3.5 UICC/SIM/USIM Interface 28 3.5 UICC/SIM/USIM Interface PH8/PH8-P has an integrated UICC/SIM/USIM interface compatible with the 3GPP 31.102 and ETSI 102 221. This is wired to the host interface in order to be connected to an external SIM card holder. Six pins on the board-to-board connector are reserved for the SIM interface. The UICC/SIM/USIM interface supports 3V and 1.8V SIM cards. The CCIN signal serves to detect whether a tray (with SIM card) is present in the card holder. Using the CCIN signal is mandatory for compliance with the GSM 11.11 recommendation if the mechanical design of the host application allows the user to remove the SIM card during oper-
ation. To take advantage of this feature, an appropriate SIM card detect switch is required on the card holder. For example, this is true for the model supplied by Molex, which has been test-
ed to operate with PH8/PH8-P and is part of the Cinterion reference equipment submitted for type approval. See Chapter 9 for Molex ordering numbers. Table 9: Signals of the SIM interface (board-to-board connector) Signal CCGND Separate ground connection for SIM card to improve EMC. Description Be sure to use this ground line for the SIM interface rather than any other ground line or plane on the module. Chipcard clock CCCLK CCVCC SIM supply voltage. CCIO CCRST CCIN Serial data line, input and output. Chipcard reset Input on the baseband processor for detecting a SIM card tray in the holder. If the SIM is removed during operation the SIM interface is shut down immediately to prevent destruc-
tion of the SIM. The CCIN signal is active low. The CCIN signal is mandatory for applications that allow the user to remove the SIM card during operation. The CCIN signal is solely intended for use with a SIM card. It must not be used for any other purposes. Failure to comply with this requirement may invalidate the type approval of PH8/
PH8-P. Note: No guarantee can be given, nor any liability accepted, if loss of data is encountered after removing the SIM card during operation. Also, no guarantee can be given for properly initializ-
ing any SIM card that the user inserts after having removed the SIM card during operation. In this case, the application must restart PH8/PH8-P. PH8_PH8-P_HD_v02.000 Confidential / Released Page 25 of 46 2011-10-21 PH8/PH8-P Hardware Interface Overview 3.5 UICC/SIM/USIM Interface 28 open: Card removed closed: Card inserted 1n SIM /
UICC CCIN CCRST CCCLK CCGND CCIO r o t c e n n o c d r a o b
o t
d r a o B Module CCVCC 220n Figure 4: UICC/SIM/USIM interface The total cable length between the board-to-board connector pins on PH8/PH8-P and the pads of the external SIM card holder must not exceed 100mm in order to meet the specifications of 3GPP TS 51.010-1 and to satisfy the requirements of EMC compliance. To avoid possible cross-talk from the CCCLK signal to the CCIO signal be careful that both lines are not placed closely next to each other. A useful approach is using the CCGND line to shield the CCIO line from the CCCLK line. PH8_PH8-P_HD_v02.000 Confidential / Released Page 26 of 46 2011-10-21 PH8/PH8-P Hardware Interface Overview 3.6 Analog Audio Interface 28 3.6 Analog Audio Interface PH8/PH8-P has an analog audio interface with a balanced analog microphone input and a bal-
anced analog earpiece output. A supply voltage and an analog ground connection are provided at dedicated lines. PH8/PH8-P offers eight audio modes which can be selected with the AT^SNFS command. The electrical characteristics of the voiceband part vary with the audio mode. For example, sending and receiving amplification, sidetone paths, noise suppression etc. depend on the selected mode and can in parts be altered with AT commands (except for mode 1). When shipped from factory, all audio parameters of PH8/PH8-P are set to audio mode 1. This is the default configuration optimised for the Votronic HH-SI-30.3/V1.1/0 handset and used for type approving the Cinterion Wireless Modules reference configuration. Audio mode 1 has fix parameters which cannot be modified. To adjust the settings of the Votronic handset simply change to another audio mode. 3.7 Digital Audio Interface PH8/PH8-P supports a digital audio interface that can be employed either as pulse code mod-
ulation or as inter IC sound interface. Operation of these interface variants is mutually exclu-
sive. PH8_PH8-P_HD_v02.000 Confidential / Released Page 27 of 46 2011-10-21 PH8/PH8-P Hardware Interface Overview 4 GPS Receiver 28 4 GPS Receiver PH8/PH8-P integrates a GPS receiver that offers the full performance of GPS technology. The GPS receiver is able to continuously track all satellites in view, thus providing accurate satellite position data. The integrated GPS receiver supports the NMEA protocol via USB or ASC0 interface. NMEA is a combined electrical and data specification for communication between various (marine) electronic devices including GPS receivers. It has been defined and controlled by the US-
based National Marine Electronics Association. For more information on the NMEA Standard please refer to http://www.nmea.org. Depending on the receivers knowledge of last position, current time and ephemeris data, the receivers startup time (i.e., TTFF = Time-To-First-Fix) may vary: If the receiver has no knowl-
edge of its last position or time, a startup takes considerably longer than if the receiver has still knowledge of its last position, time and almanac or has still access to valid ephimeris data and the precise time. By default, the GPS receiver is switched off. It has to be switched on and configured using AT commands. For more information on how to control the GPS interface via the AT command AT^SGPSC see [1]. PH8_PH8-P_HD_v02.000 Confidential / Released Page 28 of 46 2011-10-21 PH8/PH8-P Hardware Interface Overview 5 Antenna Interfaces 34 5 5.1 Antenna Interfaces GSM/UMTS Antenna Interface The PH8/PH8-P GSM/UMTS antenna interface comprises a main GSM/UMTS antenna as well as an optional UMTS Rx diversity antenna to improve signal reliability and quality1. The inter-
face has an impedance of 50. PH8/PH8-P is capable of sustaining a total mismatch at the antenna interface without any damage, even when transmitting at maximum RF power. The external antenna must be matched properly to achieve best performance regarding radi-
ated power, DC-power consumption, modulation accuracy and harmonic suppression. Match-
ing networks are not included on the PH8/PH8-P PCB and should be placed in the host application, if the antenna does not have an impendance of 50. Regarding the return loss PH8/PH8-P provides the following values in the active band:
Table 10: Return loss in the active band State of module Receive Transmit Idle Return loss of module
> 8dB not applicable
< 5dB Recommended return loss of application
> 12dB
> 12dB not applicable The connection of the antenna or other equipment must be decoupled from DC voltage. This is necessary because the antenna connector is DC coupled to ground via an inductor for ESD protection. 5.1.1 Antenna Installation The U.FL antenna connector from Hirose/Molex of the main GSM/UMTS antenna has been chosen as antenna reference point (ARP) for the Cinterion Wireless Modules reference equip-
ment submitted to type approve PH8/PH8-P. See Section 5.1.2 for details. All RF data specified throughout this manual is related to the ARP. The positions of the modules antenna connectors can be seen in Figure 9. 1. By delivery default the optional UMTS Rx diversity antenna is configured as available for the module. To avoid negative side effects and performance degradation it is recommended to disable the diversity an-
tenna path if
- the host application does not support a diversity antenna
- the host application includes a diversity antenna - but a 3G network simulator is used for development and performance tests. Please refer to [1] for details on how to configure antenna settings. PH8_PH8-P_HD_v02.000 Confidential / Released Page 29 of 46 2011-10-21 PH8/PH8-P Hardware Interface Overview 5.1 GSM/UMTS Antenna Interface 34 5.1.2 Antenna Connector PH8/PH8-P uses either an ultra-miniature SMT antenna connector from Hirose Ltd: U.FL-R-
SMT, or the Molex 07341201 U.FL antenna connector. Both connectors have identical me-
chanical dimensions (see Figure 5). Minor differences in product specifications are mentioned in Table 11. The position of the antenna connectors on the PH8/PH8-P board can be seen in Figure 9. Figure 5: Mechanical dimensions of PH8/PH8-P antenna connectors Specification Table 11: Product specifications of PH8/PH8-P antenna connectors Item Ratings Nominal impedance Rated frequency Mechanical characteristics Repetitive operation 50 DC to 3GHz Contact resistance:
Center 25m Outside 15m No momentary disconnections of 1s. No damage, cracks and looseness of parts. No momentary disconnections of 1s. No damage, cracks and looseness of parts. No damage, cracks and looseness of parts. Insulation resistance:
100M min. at high humidity 500M min. when dry No damage, cracks and looseness of parts. Contact resistance:
Center 25m Outside 15m No excessive corrosion Vibration Shock Environmental characteristics Humidity resistance Temperature cycle Salt spray test Conditions Operating temp:-40C to + 90C Operating humidity: max. 90%
30 cycles of insertion and disen-
gagement Frequency of 10 to 100Hz, single amplitude of 1.5mm, acceleration of 59m/s2, for 5 cycles in the direc-
tion of each of the 3 axes Acceleration of 735m/s2, 11ms duration for 6 cycles in the direc-
tion of each of the 3 axes Exposure to 40C, humidity of 95% for a total of 96 hours Temperature: +40C 5 to 35C
+90C 5 to 35C Time: 30min within 5min 30min within 5min 48 hours continuous exposure to 5% salt water PH8_PH8-P_HD_v02.000 Confidential / Released Page 30 of 46 2011-10-21 PH8/PH8-P Hardware Interface Overview 5.1 GSM/UMTS Antenna Interface 34 Table 12: Material and finish of PH8/PH8-P antenna connectors and recommended plugs Part Shell Material Phosphor bronze Finish Hirose: Silver plating Molex: Gold plating Gold plating Gold plating Hirose: Beige, Molex: Ivory Male center contact Female center contact Insulator Brass Phosphor bronze Receptacle: LCP Mating plugs and cables can be chosen from the Hirose U.FL Series or from other antenna equipment manufacturers like Molex or IMS. Examples from the Hirose U.FL Series are shown below and listed in Table 13. For latest product information please contact your respective an-
tenna equipment manufacturer. Figure 6: U.FL-R-SMT connector with U.FL-LP-040 plug Figure 7: U.FL-R-SMT connector with U.FL-LP-066 plug PH8_PH8-P_HD_v02.000 Confidential / Released Page 31 of 46 2011-10-21 PH8/PH8-P Hardware Interface Overview 5.1 GSM/UMTS Antenna Interface 34 In addition to the connectors illustrated above, the U.FL-LP-(V)-040(01) version is offered as an extremely space saving solution. This plug is intended for use with extra fine cable (up to 0.81mm) and minimizes the mating height to 2mm. See Figure 8 which shows the Hirose data sheet. Figure 8: Specifications of U.FL-LP-(V)-040(01) plug PH8_PH8-P_HD_v02.000 Confidential / Released Page 32 of 46 2011-10-21 PH8/PH8-P Hardware Interface Overview 5.1 GSM/UMTS Antenna Interface 34 Part number U.FL-R-SMT U.FL-LP-040 Table 13: Ordering information for Hirose U.FL Series Item Connector on PH8/PH8-P Right-angle plug shell for 0.81mm cable Right-angle plug for 0.81mm cable Right-angle plug for 1.13mm cable Right-angle plug for 1.32mm cable Extraction jig U.FL-LP-068 U.FL-LP-066 E.FL-LP-N U.FL-LP(V)-040 (01) HRS number CL331-0471-0-10 CL331-0451-2 CL331-053-8-01 CL331-0452-5 CL331-0452-5 CL331-04441-9 PH8_PH8-P_HD_v02.000 Confidential / Released Page 33 of 46 2011-10-21 PH8/PH8-P Hardware Interface Overview 5.2 GPS Antenna Interface 34 5.2 GPS Antenna Interface In addition to the RF antenna interface PH8/PH8-P also has a GPS antenna interface. See Section 6.1 to find out where the GPS antenna connector is located. The GPS antenna instal-
lation and connector are the same as for the RF antenna interface (see Section 5.1.1 and Sec-
tion 5.1.2). It is possible to connect active or passive GPS antennas. In either case they must have 50 Ohm impedance. The simultaneous operation of GSM and GPS has been implemented. Active 3V GPS antennas can be supplied via the GPS antenna interface, if the supply voltage is switched on. This is done by AT command: AT^SGPSC="Power/Antenna" to configure the use of an active GPS antenna and AT^SGPSC="Engine" to start the GPS receiver (for com-
mand details see [1]). The available current is limited to prevent short circuits. PH8_PH8-P_HD_v02.000 Confidential / Released Page 34 of 46 2011-10-21 PH8/PH8-P Hardware Interface Overview 6 Mechanics 40 6 6.1 Mechanics Mechanical Dimensions of PH8/PH8-P Figure 9 shows the top view of PH8/PH8-P and provides an overview of the board's mechanical dimensions. For further details see Figure 10. Length:
Width:
Height:
50.00mm 33.90mm 3.10mm GSM/UMTS antenna Pin 1 Pin 80 Application interface
(board-to-board connector) Pin 41 Pin 40 Top view UMTS diversity antenna GPS antenna Bottom view Figure 9: PH8/PH8-P top and bottom view PH8_PH8-P_HD_v02.000 Confidential / Released Page 35 of 46 2011-10-21 PH8/PH8-P Hardware Interface Overview 6.1 Mechanical Dimensions of PH8/PH8-P 40 Figure 10: Dimensions of PH8/PH8-P (all dimensions in mm) PH8_PH8-P_HD_v02.000 Confidential / Released Page 36 of 46 2011-10-21 PH8/PH8-P Hardware Interface Overview 6.2 Mounting PH8/PH8-P to the Application Platform 40 6.2 Mounting PH8/PH8-P to the Application Platform There are many ways to properly install PH8/PH8-P in the host device. An efficient approach is to mount the PH8/PH8-P PCB to a frame, plate, rack or chassis. Fasteners can be M2 screws plus suitable washers, circuit board spacers, or customized screws, clamps, or brackets. In addition, the board-to-board connection can also be utilized to achieve better support. For proper grounding it is strongly recommended to use large ground plane on the bottom of board in addition to the five GND pins of the board-to-board connector. The ground plane may also be used to attach cooling elements, e.g. a heat sink or thermally conductive tape. To prevent mechanical damage, be careful not to force, bend or twist the module. Be sure it is positioned flat against the host device. 6.3 Board-to-Board Application Connector This section provides the specifications of the 80-pin board-to-board connector used to connect PH8/PH8-P to the external application. Connector mounted on the PH8/PH8-P module:
Type:
52991-0808 SlimStack Receptacle 80 pins, 0.50mm pitch, for stacking heights of 3.0 or 4.0mm, see Figure 12 for details. Supplier: Molex, http//www.molex.com PH8_PH8-P_HD_v02.000 Confidential / Released Page 37 of 46 2011-10-21 PH8/PH8-P Hardware Interface Overview 6.3 Board-to-Board Application Connector 40 Specification (80-pin B2B connector) 80 0.5mm (.020") 50V 0.5A max per contact 50m max per contact
> 100M 500V AC (for 1 minute) Table 14: Technical specifications of Molex board-to-board connector Parameter Electrical Number of Contacts Contact spacing Voltage Rated current Contact resistance Insulation resistance Dielectric Withstanding Voltage Physical Insulator material (housing) Contact material Insertion force 1st Insertion force 30th Withdrawal force 1st Maximum connection cycles White glass-filled LCP plastic, flammability UL 94V 0 Plating: Gold over nickel
< 74.4N
< 65.6N
> 10.8N 30 (@ 70m max per contact) Mating connector types for the customer's application offered by Molex:
Figure 11: Mating board-to-board connector 53748-0808 on application 53748-0808 SlimStack Plug, 3mm stacking height, see Figure 13 for details. 53916-0808 SlimStack Plug, 4mm stacking height Note: There is no inverse polarity protection for the board-to-board connector. It is therefore very important that the board-to-board connector is connected correctly to the host application, i.e., pin1 must be connected to pin1, pin2 to pin 2, etc. Pin locations are shown in Figure 9. PH8_PH8-P_HD_v02.000 Confidential / Released Page 38 of 46 2011-10-21 PH8/PH8-P Hardware Interface Overview 6.3 Board-to-Board Application Connector 40 Figure 12: Molex board-to-board connector 52991-0808 on PH8/PH8-P PH8_PH8-P_HD_v02.000 Confidential / Released Page 39 of 46 2011-10-21 PH8/PH8-P Hardware Interface Overview 6.3 Board-to-Board Application Connector 40 Figure 13: Mating board-to-board connector 53748-0808 on application PH8_PH8-P_HD_v02.000 Confidential / Released Page 40 of 46 2011-10-21 PH8/PH8-P Hardware Interface Overview 7 Sample Application 42 7 Sample Application Figure 14 shows a typical example of how to integrate an PH8/PH8-P module with an applica-
tion. The audio interface demonstrates the balanced connection of microphone and earpiece. This solution is particularly well suited for internal transducers. The PWR_IND line is an open collector that needs an external pull-up resistor which connects to the voltage supply VCC C of the microcontroller. Low state of the open collector pulls the PWR_IND signal low and indicates that the PH8/PH8-P module is active, high level notifies the Power-down mode. If the module is in Power-down mode avoid current flowing from any other source into the mod-
ule circuit, for example reverse current from high state external control lines. Therefore, the controlling application must be designed to prevent reverse flow. If an external level controller is required, this can be done by using for example a 5V I/O tolerant buffer/driver like a
"74AVC4T245" with OE (Output Enable) controlled by PWR_IND. The EMC measures are best practice recommendations. In fact, an adequate EMC strategy for an individual application is very much determined by the overall layout and, especially, the po-
sition of components. Disclaimer:
No warranty, either stated or implied, is provided on the sample schematic diagram shown in Figure 14 and the information detailed in this section. As functionality and compliance with na-
tional regulations depend to a great amount on the used electronic components and the indi-
vidual application layout manufacturers are required to ensure adequate design and operating safeguards for their products using PH8/PH8-P modules. PH8_PH8-P_HD_v02.000 Confidential / Released Page 41 of 46 2011-10-21 PH8/PH8-P Hardware Interface Overview 7 Sample Application 42 Figure 14: PH8/PH8-P sample application PH8_PH8-P_HD_v02.000 Confidential / Released Page 42 of 46 2011-10-21 PH8/PH8-P Hardware Interface Overview 8 Reference Approval 44 8 8.1 Reference Approval Reference Equipment for Type Approval The Cinterion Wireless Modules reference setup submitted to type approve PH8/PH8-P is shown in the following figure1. The module is connected to the DSB75 via a special adapter and either mounted directly onto the adapter or connected using a flex cable:
Figure 15: Reference equipment for type approval 1. For RF performance tests a mini-SMT/U.FL to SMA adapter with attached 6dB coaxial attenuator is cho-
sen to connect the module directly to the GSM/UMTS/GPS test equipment instead of employing the SMA antenna connectors on the PH8/PH8-P-DSB75 adapter as shown in Figure 15. The following products are recommended:
Hirose SMA-Jack/U.FL-Plug conversion adapter HRMJ-U.FLP(40)
(for details see see http://www.hirose-connectors.com/ or http://www.farnell.com/
Aeroflex Weinschel Fixed Coaxial Attenuator Model 3T/4T
(for details see http://www.aeroflex.com/ams/weinschel/pdfiles/wmod3&4T.pdf) PH8_PH8-P_HD_v02.000 Confidential / Released Page 43 of 46 2011-10-21 PH8/PH8-P Hardware Interface Overview 8.2 Compliance with FCC and IC Rules and Regulations 44 8.2 Compliance with FCC and IC Rules and Regulations The Equipment Authorization Certification for the Cinterion Wireless Modules reference appli-
cation described in Section 8.1 will be registered under the following identifiers:
PH8:
FCC Identifier QIPPH8 Industry Canada Certification Number: 7830A-PH8 Granted to Cinterion Wireless Modules GmbH PH8-P:
FCC Identifier QIPPH8-P Industry Canada Certification Number: 7830A-PH8P Granted to Cinterion Wireless Modules GmbH Manufacturers of mobile or fixed devices incorporating PH8/PH8-P modules are authorized to use the FCC Grants and Industry Canada Certificates of the PH8/PH8-P modules for their own final products according to the conditions referenced in these documents. In this case, the FCC label of the module shall be visible from the outside, or the host device shall bear a second label stating "Contains FCC ID QIPPH8" resp. "Contains FCC ID QIPPH8-P", and accordingly Con-
tains IC 7830A-PH8 resp. Contains IC 7830A-PH8P. The integration is limited to fixed or mo-
bile categorised host devices, where a separation distance between the antenna and any person of min. 20cm can be assured during normal operating conditions. For mobile and fixed operation configurations the antenna gain, including cable loss, must not exceed the limits that are stated on the FCC Grant. IMPORTANT:
Manufacturers of portable applications incorporating PH8/PH8-P modules are required to have their final product certified and apply for their own FCC Grant and Industry Canada Certificate related to the specific portable mobile. This is mandatory to meet the SAR requirements for por-
table mobiles. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Connect the equipment into an outlet on a circuit different from that to which the receiver Increase the separation between the equipment and receiver. is connected. Consult the dealer or an experienced radio/TV technician for help. PH8_PH8-P_HD_v02.000 Confidential / Released Page 44 of 46 2011-10-21 PH8/PH8-P Hardware Interface Overview 9 Appendix 46 9 Appendix List of Parts and Accessories 9.1 Table 15: List of parts and accessories Description PH8 Supplier Cinterion PH8-P Cinterion DSB75 Support Box DSB75 adapter for mounting the PH8/PH8-P evaluation module Votronic Handset Cinterion Cinterion VOTRONIC Ordering information Standard module Cinterion Wireless Modules IMEI:
Ordering number: L30960-N1900-A200 Customer IMEI:
Ordering number: L30960-N1905-A200 Standard module Cinterion Wireless Modules IMEI:
Ordering number: L30960-N1910-A200 Customer IMEI:
Ordering number: L30960-N1915-A200 Ordering number: L36880-N8811-A100 Ordering number: L30960-N1802-A100 Votronic HH-SI-30.3/V1.1/0 VOTRONIC Entwicklungs- und Produktionsgesellschaft fr elek-
tronische Gerte mbH Saarbrcker Str. 8 66386 St. Ingbert Germany Phone: +49-(0)6 89 4 / 92 55-0 Fax: +49-(0)6 89 4 / 92 55-88 Email: contact@votronic.com Ordering numbers: 91228 91236 Molex SIM card holder incl. push button ejector and slide-in tray Board-to-board connector U.FL antenna connector Sales contacts are listed in Table 16. Sales contacts are listed in Table 16. Molex Hirose or Molex Sales contacts are listed in Table 16 and Table 17. PH8_PH8-P_HD_v02.000 Confidential / Released Page 45 of 46 2011-10-21 PH8/PH8-P Hardware Interface Overview 9.1 List of Parts and Accessories 46 Table 16: Molex sales contacts (subject to change) Molex For further information please click:
http://www.molex.com Molex China Distributors Beijing, Room 1319, Tower B, COFCO Plaza No. 8, Jian Guo Men Nei Street, 100005 Beijing P.R. China Phone: +86-10-6526-9628 Phone: +86-10-6526-9728 Phone: +86-10-6526-9731 Fax: +86-10-6526-9730 American Headquarters Lisle, Illinois 60532 U.S.A. Phone: +1-800-78MOLEX Fax: +1-630-969-1352 Molex Japan Co. Ltd. Yamato, Kanagawa, Japan Phone: +81-462-65-2324 Fax: +81-462-65-2366 Molex Deutschland GmbH Felix-Wankel-Str. 11 4078 Heilbronn-Biberach Germany Phone: +49-7066-9555 0 Fax: +49-7066-9555 29 Email: mxgermany@molex.com Molex Singapore Pte. Ltd. Jurong, Singapore Phone: +65-268-6868 Fax: +65-265-6044 Table 17: Hirose sales contacts (subject to change) Hirose Ltd. For further information please click:
http://www.hirose.com Hirose Electric (U.S.A.) Inc 2688 Westhills Court Simi Valley, CA 93065 U.S.A. Hirose Electric UK, Ltd Crownhill Business Centre 22 Vincent Avenue, Crownhill Milton Keynes, MK8 OAB Great Britain Phone: +44-1908-305400 Fax: +44-1908-305401 Phone: +1-805-522-7958 Fax: +1-805-522-3217 Hirose Electric Co., Ltd. 5-23, Osaki 5 Chome, Shinagawa-Ku Tokyo 141 Japan Phone: +81-03-3491-9741 Fax: +81-03-3493-2933 Hirose Electric GmbH Herzog-Carl-Strasse 4 73760 Ostfildern Germany Phone: +49-711-456002-1 Fax: +49-711-456002-299 Email: info@hirose.de Hirose Electric Co., Ltd. European Branche First class Building 4F Beechavenue 46 1119PV Schiphol-Rijk Netherlands Phone: +31-20-6557-460 Fax: +31-20-6557-469 PH8_PH8-P_HD_v02.000 Confidential / Released Page 46 of 46 2011-10-21
frequency | equipment class | purpose | ||
---|---|---|---|---|
1 | 2011-10-21 | 1852.4 ~ 1907.6 | PCB - PCS Licensed Transmitter | Original Equipment |
2 | JBP - Part 15 Class B Computing Device Peripheral |
app s | Applicant Information | |||||
---|---|---|---|---|---|---|
1 2 | Effective |
2011-10-21
|
||||
1 2 | Applicant's complete, legal business name |
Gemalto M2M GmbH
|
||||
1 2 | FCC Registration Number (FRN) |
0007412448
|
||||
1 2 | Physical Address |
Siemensdamm 50
|
||||
1 2 |
Berlin, N/A 13629
|
|||||
1 2 |
Germany
|
|||||
app s | TCB Information | |||||
1 2 | TCB Application Email Address |
B******@phoenix-testlab.de
|
||||
1 2 | TCB Scope |
B1: Commercial mobile radio services equipment in the following 47 CFR Parts 20, 22 (cellular), 24,25 (below 3 GHz) & 27
|
||||
1 2 |
A1: Low Power Transmitters below 1 GHz (except Spread Spectrum), Unintentional Radiators, EAS (Part 11) & Consumer ISM devices
|
|||||
app s | FCC ID | |||||
1 2 | Grantee Code |
QIP
|
||||
1 2 | Equipment Product Code |
PH8-P
|
||||
app s | Person at the applicant's address to receive grant or for contact | |||||
1 2 | Name |
A**** H******
|
||||
1 2 | Title |
Manager Certifications
|
||||
1 2 | Telephone Number |
00493********
|
||||
1 2 | Fax Number |
00493********
|
||||
1 2 |
a******@gemalto.com
|
|||||
app s | Technical Contact | |||||
n/a | ||||||
app s | Non Technical Contact | |||||
n/a | ||||||
app s | Confidentiality (long or short term) | |||||
1 2 | Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
1 2 | Long-Term Confidentiality Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
1 2 | If so, specify the short-term confidentiality release date (MM/DD/YYYY format) | 12/31/2011 | ||||
if no date is supplied, the release date will be set to 45 calendar days past the date of grant. | ||||||
app s | Cognitive Radio & Software Defined Radio, Class, etc | |||||
1 2 | Is this application for software defined/cognitive radio authorization? | No | ||||
1 2 | Equipment Class | PCB - PCS Licensed Transmitter | ||||
1 2 | JBP - Part 15 Class B Computing Device Peripheral | |||||
1 2 | Description of product as it is marketed: (NOTE: This text will appear below the equipment class on the grant) | GSM/GPRS/UMTS/HSPA Module | ||||
1 2 | Related OET KnowledgeDataBase Inquiry: Is there a KDB inquiry associated with this application? | No | ||||
1 2 | Modular Equipment Type | Single Modular Approval | ||||
1 2 | Purpose / Application is for | Original Equipment | ||||
1 2 | Composite Equipment: Is the equipment in this application a composite device subject to an additional equipment authorization? | Yes | ||||
1 2 | Related Equipment: Is the equipment in this application part of a system that operates with, or is marketed with, another device that requires an equipment authorization? | No | ||||
1 2 | Grant Comments | Output power listed is peak conducted. This device contains functions that are not operational in U.S Territories. This filing is only applicable for US operations. This OEM module is approved for use in products operating as fixed or portable transmitting device. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. A separate approval is required for portable operating configurations, as defined in 2.1093 of the rules. The final product operating with this transmitter must include operating instructions and applicable warnings for endusers and installers to satisfy RF exposure compliance requirements. Antenna gain must meet RF exposure and max radiated output power limits of the applicable rule section. This Grant is valid only when the device is sold to OEM integrators and the OEM integrators are instructed to ensure that the end user has no manual instructions to remove or install the device. The max. antenna gain for this device as reported to the FCC is: 0.89 dBi (850MHz) and 1.6 dBi (1900MHz). | ||||
1 2 | Is there an equipment authorization waiver associated with this application? | No | ||||
1 2 | If there is an equipment authorization waiver associated with this application, has the associated waiver been approved and all information uploaded? | No | ||||
app s | Test Firm Name and Contact Information | |||||
1 2 | Firm Name |
7layers AG
|
||||
1 2 | Name |
R****** M******
|
||||
1 2 | Telephone Number |
49-21********
|
||||
1 2 | Fax Number |
49-21********
|
||||
1 2 |
r******@7layers.de
|
|||||
Equipment Specifications | |||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
1 | 1 | 22H | 824.2 | 848.8 | 2.588 | 2.5 ppm | 247KGXW | ||||||||||||||||||||||||||||||||||
1 | 2 | 22H | 824.2 | 848.8 | 1.107 | 2.5 ppm | 247KG7W | ||||||||||||||||||||||||||||||||||
1 | 3 | 22H | 826.4 | 846.6 | 1.122 | 2.5 ppm | 4M19F9W | ||||||||||||||||||||||||||||||||||
1 | 4 | 24E | 1850.2 | 1909.8 | 1.318 | 2.5 ppm | 249KGXW | ||||||||||||||||||||||||||||||||||
1 | 5 | 24E | 1850.2 | 1909.8 | 0.968 | 2.5 ppm | 251KG7W | ||||||||||||||||||||||||||||||||||
1 | 6 | 24E | 1852.4 | 1907.6 | 1.38 | 2.5 ppm | 4M17F9W | ||||||||||||||||||||||||||||||||||
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
2 | 1 | 15B |
some individual PII (Personally Identifiable Information) available on the public forms may be redacted, original source may include additional details
This product uses the FCC Data API but is not endorsed or certified by the FCC