Bluetooth Sound Bar with Built-In Subwoofer CHT912 INSTRUCTION MANUAL FCC Warnings WARNING:Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be collocated or operating in conjunction with any other antenna or transmitter unless authorized to do so by the FCC. AC/DC adapter 1. Placing on the table Ventilation When placing the Sound Bar on an entertainment center, bookshelf, or any type of enclosed space, be sure to allow at least 2-3 inches of space around the Sound Bar for ventilation. If the Sound Bar is enclosed in a tight space, without ventilation, heat generated from the Sound Bar could produce a potential heat hazard. 2. Mounting the Speaker Bar onto a wall We recommend having this speaker professionally mounted. By using the included wall mounting accessories, the sound bar can be mounted onto a wall. Distance Between Two Brackets You will need :
Level Pencil Tape Measure Manual or Electric drill 2.1. Mounting on the wooden wall You should use 2 pieces of short screws 2 pieces of EVA 1. Use the TAPE MEASURE to decide how high youd like to hang the sound bar on the wall. The sound bar must be hung within 5 feet of an AC power outlet for the attached AC power cord to reach. 2. Mark the position of the mounting screws on the wall using a pencil. 3. Line the LEVEL up on both of your mark sure they are level. If they're not, adjust the marks as needed to make them level. 4. After you've double checked your marks, drill through the EVA with screw directly into the marks that you have made on the wall. 5. Use the LEVEL to check that the mounting screws are level. 6. Put the sound bar onto the mounting brackets, and make sure there is a firm and stable connection before letting go of the sound bar. 7. Finally, use the LEVEL to confirm that the sound bar is level. 4 2.2. Mounting on the dry wall You should use 2 pieces of EVA 2 pieces of short screws 2 pieces of plastic tubes
(1)
(2)
1. REMOTE SENSOR: Ensure this area is not covered or blocked by any object. 2. STANDBY button: Press to turn the speaker bar off or on. 3. SOURCE button: Press to switch between Bluetooth receiver, AUX, LINE in and FM. 4. VOLUME +: Press to increase the volume. 5. VOLUME -: Press to decrease the volume 6. MUTE: Press to mute the volume. 7. STANDBY Indicator. 8. FM Indicator. 9. Bluetooth Indicator. 10. AUX Indicator. 11. LINE IN Indicator. 12. FM antenna port. 13. AUX L/R IN: To insert RCA cable. 14. LINE IN jack: To insert LINE in cable. 15. DC jack in. 16. Mounting bracket. 6 1. STANDBY button: Press to turn the unit on or off. 2. BT button: Press to switch to Bluetooth mode. 3. SCAN button: Press to scan for available radio stations in FM Radio mode. 4. MUSIC button: Press to switch to the EQ optimized for music. 5. TREBLE button: Press to adjust the treble up or down. 5. VOL- button: Press to decrease the volume. 6. AUX button: Press to switch to AUX mode. 7. MUTE button: Press to mute the volume. 8. LINE button: Press to switch to LINE In mode. 9. FM button: Press to switch to FM Radio mode. 10. CHANNEL + button: Press to adjust the channel up. 11. CHANNEL - button: Press to adjust the channel down. 12. MOVIE button: Press to switch to the EQ optimized for movie sound. 13. VOICE button: Press to switch to the EQ optimized for dialogue. 14. BASS button: Press to adjust the bass up or down. 15. VOLUME button: Press to adjust the volume. 7 N E P O H S U P ell 2 5 C m L V 0 C U S 3 Lithiu C 2 R Lithiu m C ell C R 2025 S C U L 3V OPEN PUSH 1. It includes one 2025 button cell battery.
(pre-installed) 2. Removes the transparent sheet. 5 2 0 2 R C 8 Audio Inputs
(1) Using the Stereo RCA Inputs When connecting two products using an RCA Cable, match the colored ports with the same colored connection. Before use, disconnect any cables connected to the LINE IN. 1. Connect the RCA Cable to the RCA Stereo Inputs located on the back of the unit, and to the audio outputs on the television. 2. Press the STANDBY button to power on the unit. 3. Press the AUX button on the remote or SOURCE button on the unit repeatedly to enter aux mode. 4. Audio played through the television will now be heard through the speakers.
(2) Using the LINE IN 1. Plug one end of a 3.5 mm audio input cable into the LINE IN on the unit. Before use, disconnect any cables connected to the Stereo RCA Inputs. 2. Plug the other end of the cable into the audio output /headphone output on an MP3 Player or other audio source. 3. Press the STANDBY button to power the unit on. 4. Press the LINE button on the remote or SOURCE button on the unit repeatedly to enter line in mode. 5. Audio played through the connected device will now be heard through the speakers. LISTEN WITH BLUETOOTH RECEIVER 1. Switch on the sound bar and select BT on the remote or SOURCE button on the unit repeatedly to select bluetooth function. 2. Bluetooth blue LED indicator will flash and blink. Turn on your device, such as iPod, iPhone, iPAD, tablets and mobiles etc, with bluetooth transmitters to search for the sound bar. 3. When your device have successfully searched for the sound bar, it will show the name of CHT912. Enter the default password "0000" to pair with. 9 4. When successfully paired and connected, blue LED indicator will be light only and stop blinking. 5. If your device should become upaired or it is unable to connect, blue LED indicator will continue flashing and blinking. Repeat the above steps to try to pairing. 6. If the initial set up connection is succesful, the next time the speaker is turned on , the speaker will automatically pair to the last device it was connected with . NOTE:
1. The Bluetooth speaker only connects to device at a time . Turn off the Bluetooth speaker in order to pair the device with another Bluetooth device. 2. The maximum transmission between the Bluetooth speaker and a device is 10 meters or 32 feet . 3. Interferece may occur during playback when using the Bluetooth function near other wireless devices. If playback through Bluetooth is problematic, move the Bluetooth speaker and the playback device to a different location , or use the 3.5mm audio cable jack instead of the Bluetooth function . LISTEN TO FM RADIO Extend the FM antenna wire on the rear of the unit and relocate it to get the best reception. Tuning the Radio 1. Power on the unit as pervious procedures. 2. Press the FM button on the remote or SOURCE button on the unit to enter FM radio mode. 3. Press the SCAN button on the remote. 4. The bar speaker will scan for all available stations, and store them. 5. Press the CH+/- buttons on the remote to browse through stored stations. 6. Total stations available is 30. BUILT-IN EQUALIZER It presets 3 bands equalizer. Press the MUSIC, MOVIE and VOICE button on the remote control to cycle through it. 1. MUSIC mode. Press to switch to the EQ optimized for music. Adjust your preferences by pressing the TREBLE and BASS buttons. 2. MOVIE mode. Press to switch to the EQ optimized for movie sound. Under this mode, TREBLE and BASS are invalid. 3. VOICE mode. Press to switch to the EQ optimized for dialogue. Under this mode, TREBLE and BASS are invalid. 10 Problem No power What to do Check that the power is switched on at the wall. Check if the power cord is properly connected to the power outlet. No sound Check that the volume control is NOT at minimum setting. Check that it is NOT set to mute. Function disturbed If none of the above solutions work, then switch off and unplug your Speaker system, leaving it for 2 minutes and then switching it back on again. The remote control won' t work Inspect or replace the batteries. Make sure there are no obstacles obscuring the front of the Speaker. No sound from bluetooth first connection Check if you have entered password or not. It needs to start with password "0000". Maintenance 1. Do not use harsh or abrasive cleaning agents or solvents. 2. Do not attempt to disassemble your product. 3. Do not paint your product. 4. Do not drop, throw or try to bend your product. 5. Do not expose your product to open flames. 11 Power Source :. AC120V, 60Hz Power Source of Remote Control:DC 3V, 1X CR2025 battery (Included) Power Consumption:.< 1W Audio Power :
Woofer ............ 30W Left Channel ...........10W Right Channel.............10W Radio Coverage .................. FM 87.5-108.0 MHz Impedance of Speakers :
Woofer ........ 8 Ohm,18W x 2 Left Channel .......... 4 Ohm,12W Right Channel......... 4 Ohm,12W 1 x Users Manual 1 x Remote Control 1 x AC/DC Adaptor 1 x RCA cable 1 x 3.5mm LINE in cable 2 x Screws 2 x Plastic Tubes 2 x EVA spacer 12