FCC ID: MXF-WLTGG1334846 Cat 12/13 LTE TDD CBRS+B46 HE Outdoor CPE

LTE CPE Quick installation Guide WLTGG-133 LTE Outdoor CPE Contents CONTENTS ........................................................ 1 1. CONNECTORS ................................................ 2 2. LED INDICATORS .......................................... 3 3. INSTALLING LTE OUTDOOR CPE .................... 4 4. CONNECTING THE CABLES ............................ 7 5. WEB INTERFACE ........................................... 9 1 Connectors 1. One RJ-45 connector for connecting to the PoE adaptor. 2. LED indicator inside and SIM card slot for inserting SIM card. 3. A grounding screw on the rear panel. 2 LED Indicators LED name Location Color LED Behavior Status Indication LED List MAIN power Blue ON OFF Power On Power Off Ethernet status Orange Steady ON Detect Ethernet Device Connected SIM status Green Blinking N/A OFF Steady ON Blinking when On-hook OFF No Ethernet connection SIM DETECTED (with LTE connection) SIM NO DETECTED / SIM NOT INSERTED SIM DETECTED (without LTE connection) LTE Status LED : Link Status When CPE is power on, each LED indicates each link status ; change upon customer Blue Blue Blue Blue Blue requirement Steady ON Steady ON Steady ON Steady ON Steady ON Signal is poor SINR < 7dB Signal is weak 7dB <SINR <11dB Signal is Good 11dB < SINR <18dB Signal is very good 18dB < SINR <23dB Signal is Excellent SINR>=23dB LTE 1 LTE 2 LTE 3 LTE 4 LTE 5 3 Installing LTE outdoor CPE Selecting a Location: LTE Outdoor CPE should be pole-mounted outdoors and aligned so its antenna faces the nearest LTE eNB. When selecting a suitable location for the unit, consider these guidelines:

Place LTE Outdoor CPE as high as possible to achieve the best possible link quality. surfaces. Place the LTE Outdoor CPE away from power and telephone lines. Avoid placing LTE Outdoor CPE too close to any metallic reflective Be sure to ground LTE Outdoor CPE with an appropriate grounding wire (not included) by attaching it to the grounding screw on the unit and to a good ground connection. Mounting the ODU: Mount LTE Outdoor CPE on a 1-4 pole using the supplied kit, or the optional tilt accessory. Using the clamp [Unadjustable angle]

1. Thread the M10*100mm bolt through a spring washer, flat washer and the bracket holes. 2. With the connector facing downward, attach LTE Outdoor CPE to a 1-4 pole. 3. Attach the bracket to the other side of the pole. 4. Thread the M10*100mm bolts through both holes on either side, and tighten the nuts. 4 Using the clamp [adjustable angle] Type1 1. Thread the M10*20mm bolt through a spring washer, flat washer and the bracket holes, and tighten the bolts to the LTE Outdoor CPE. 2. Thread the M10*100mm bolt through a spring washer, flat washer and the holes of bracket A. Attach the bracket A to the other side of the pole and through both holes of the bracket B on either side, and tighten the bolts. 3. With the connector facing downward, and assembling two brackets together. Thread the M10*20mm bolt through a spring washer, flat washer and the bracket holes. 5 4. Adjust the required angle and lock the screws. This is an angle that can be adjusted 10 degrees above and below. Using the clamp [adjustable angle] Type2 1. Locate the mid bracket and remove the two M10x1.5 (25mm L) screws from it by unscrewing the two M10 lock nuts. Set the screws and nuts aside. Secure the pole side bracket with the mid bracket by inserting two M10x1.5 (25mm L) screws through both brackets and fastened with two M10x1.5 lock nuts. Please take note of the mid brackets orientation, ensuring that the arrow is pointing up. You should position the mid bracket in the middle position of pole side bracket and adjust it after attaching the CPE (See Step 4) 6 Please ensure that the M10x1.5, 16mm L screw (#A) on the top hole and the M6 enlarged hex head screw (#B) on the bottom hole of the mid bracket have a distance of 4.5-7mm between the screw heads and the mid bracket surface as shown in the top view figure below. 2. SECURING BRACKET ON POLE: Take the assembled pole side bracket, hold it on one side of the pole. Slot the two M10 carriage bolts through the holes of the bracket and hold it there; take the clamp (23K-700-0291R) and slot it through the carriage bolts. Fasten the bolts with two M10x1.5 lock nuts. To assemble the unit side bracket, take the CPE and ensure that it is oriented with the arrow pointing upwards. Align the unit side bracket (23K-700-0287R) with to the back of the CPE and secure it with two M10x1.5 screws. (See figure below) 7 3. Bring the CPE up to the previously secured bracket on the pole. Hook the unit side bracket (there is a small hook on the top) onto the loosely fastened M10x1.5 screw on the mid bracket such that the hook is on the screw itself and you can tighten the screw to secure the unit. 4. Then, slide the curved bottom part of the bracket onto the M6 enlarged hex head screw. There are scorings every 5 degrees of tilt-angle, from 0 (Vertical position) to 5 (25 uptilt). Adjust the tilt to the desired angle and tighten the screw to secure the position of the CPE. You can also adjust the CPE by sliding the mid bracket left and right after loosening the lock nuts installed in Step 2 (above). There are scorings every 7 of azimuth-angle from 0 (0 position) to 2 (14 position left or right). Tighten the lock nuts when you are satisfied with the position of the CPE. 8 Connecting the Cables Outdoor Connection: Connect a grounding cable between the Ground terminal of the LTE outdoor CPE and a good ground connection. Preparing and connecting the cable: Use only 5E 4x2x24# FTP (or above) outdoor Shielded Patch Cable from an approved manufacturer. 1. Insert the RJ-45 cable:

Insert the Cat5e RJ-45 cable into the sealing gland base and connect it to the RJ-45 connector at the bottom of the ODU, labeled. Make sure that the connector is completely inserted and tightened.

((Suggest to use Cat 5E 4x2x24# F/STP outdoor Shielded Patch Cable))

((The total length of the Ethernet cables from the ODU to the IDUs RJ-45

(WAN) PoE port. Must not exceed 100m)) 2. Connect the cable Remove the sealing cable gland plug from the gland nut. Open the sealing gland nut and remove it. Don not disassembles 9 the gland base from the bracket. Insert the cable into the sealing gland base and connect it to the RJ-45 connector at the bottom of the CPE. Make sure the connector is completely inserted and tightened. Insert the rubber bushing on the cable into the gland base. Tighten the gland nut. Use the dedicated tool for fastening the sealing glands. PoE Connection 1. It is assumed that the RJ-45 is already connected to the LTE outdoor CPE. Assemble an RJ-45 connector with a protective cover on the other end of the LTE outdoor CPE cable. 2. Connect the other end of the RJ-45 cable to the PoE adaptor which 3. Connect RJ45 cable from PoE adaptor which label LAN to a labeled PoE. PC/NB/Hub/Switch. 10 Web Interface interface:

Please follow the steps below to configure your device through the web Step1: Open the Web browser (Internet Explorer) and enter the default IP address of the ODU CPE, which is : http://192.168.15.1 Step2: Enter ODU administrator login username/password to access the web management interface. The default username/password is admin/admin . Web management interface Step3: The page shown here gets displayed in your browser after login; you can now configure the device settings. GUI Interface Mode:

LTE Operator: APN Name Signal:

(More bar means better signal)

(Disconnect, no signal) 11 Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

- Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. IMPORTANT NOTE:

FCC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 25cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 12 Professional installation instruction Please be advised that due to the unique function supplied by this product, the device is intended for use with our interactive entertainment software and licensed third-party only. The product will be distributed through controlled distribution channel and installed by trained professional and will not be sold directly to the general public through retail store. 1. Installation personal This product is designed for specific application and needs to be installed by a qualified personal who has RF and related rule knowledge. The general user shall not attempt to install or change the setting. 2. Installation location The product shall be installed at a location where the radiating antenna can be kept 25cm from nearby person in normal operation condition to meet regulatory RF exposure requirement. 3. Installation procedure Please refer to users manual for the detail. 4. Warning Please carefully select the installation position and make sure that the final output power does not exceed the limit set force in relevant rules. The violation of the rule could lead to serious federal penalty. 13 Table 1Required data collection capabilities for CBSD management software All CBSDs:

Geographic location Antenna height AGL (m) Category B Devices:

Limited to Outdoor operation Antenna gain CBSD class (Category A or B) Antenna Beam-width Requested authorization status (PAL or GAA) Antenna Azimuth Antenna Down tilt angle FCC ID Call sign (PALs only) User contact info Air interference technology Serial #

Sensing capability (if supported Contact window:

-Name of the company: CCI Products

-Address of the company: 89 Leuning Street, South Hackensack, NJ 07606

-Either phone number: +1 (201) 342-3338 14

Gemiek No.15-1 Zhonghua Road, Hsinchu Industrial Park Wireless Broadband Anywhere Hukou, Hsinchu, Taiwan 303 Web Site: www.gemtek.com.tw Phone: +886-3-598-5535 E-Mail: adam@gemteks.com FAX: +886-3-598-5585 Date: August 6, 2021 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Rd Columbia MD 21046-1609 Subject: Request for confidentiality FCC ID: MXF-WLTGG1334846 To whom it may concern:

Short-term confidentiality Pursuant to DA 04-1705 of the Commission's pubic notice, in order to comply with the marketing regulations in 47CFR 2.803 and the importation rules in 47 CFR 2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices. We are requesting the commission to grant short-term confidentiality request on the following attachments until 180 days after issue date

& Internal Photographs External Photographs

& User's manual

& Test Set up photo Permanent confidentiality Pursuant to Sections 0.457 and 0.459 of the Commission's Rules, the Applicant Hereby requests confidential treatment of information accompanying this Application As outlined below.

& Block Diagram

& Schematics

& Operational Description

& Bill of Materials

& Tune up procedure The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Should you require any further information, please contact the undersigned. Thank you for your consideration in this matter. Adam Wang/ Director |

Engineering Dept. Gemtek Technology Co., Ltd. Tel: 886 3-598-5535"1411 Fax: 886 3-597-6663 E-mail: adam@gemteks.com

Gemiek No.15-1 Zhonghua Road, Hsinchu Industrial Park Wireless Broadband Anywhere Hukou, Hsinchu, Taiwan 303 Web Site: www.gemtek.com.tw Phone: +886-3-598-5535 E-Mail: adam@gemteks.com FAX: +886-3-598-5585 Professional Installation Attestation 06 August 2021 FCC ID: MXF-WLTGG1334846 To Whom It May Concern:

Please be advised that due to the unique Market and function targeted by this product, this product will need special trained professional in configuring and installing the product. We hereby declare that the product will be distributed through controlled distribution channel which has special trained professional to install this product and will not be sold directly to the general public through retail store. Thank you for your attention. Yours sincerely, oe. Adam Wangd/ Director Engineering Dept. Gemtek Technology Co., Ltd. Tel: 886 3-598-5535*1411 Fax: 886 3-597-6663 E-mail: adam@gemteks.com

Gemiek No.16-1 Zhonghua Road, Hsinchu Industrial Park Wireless Broadband Anywhere Hukou, Hsinchu, Taiwan 303 Web Site: www.gemtek.com.tw Phone: +886-3-598-5535 E-Mail: adam@gemteks.com FAX: +886-3-598-5585 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Rd Columbia MD 21046-1609 Date: August 6, 2021 Subject: FCC Application for FCC ID: MXF-WLTGG1334846 To Whom it may concern, We, the undersigned, would like to declare that the device supports transmit power control capability and the capability to limit maximum EIRP and the maximum EIRP of associated End User Devices in response to instructions from an SAS and limit operating power to the minimum necessary for successful operations. A Wang/ Directo Nornndrne Engineering Dept. Gemtek Technology Co., Ltd. Tel: 886 3-598-5535*1411 Fax: 886 3-597-6663 E-mail: adam@gemteks.com

Gemiek No.15-1 Zhonghua Road, Hsinchu Industrial Park Wireless Broadband Anywhere Hukou, Hsinchu, Taiwan 303 Web Site: www.gemtek.com.tw Phone: +886-3-598-5535 E-Mail: adam@gemteks.com FAX: +886-3-598-5585 Date: 2021/8/6 Federal Communications Commission 7435 Oakland Mills Rd Columbia MD 21046-1609 Subject: Product Certification Representative Authorization Letter FCC ID: MXF-WLTGG1334846 To whom it may concern:

We the undersigned, hereby authorize following person to act as our agent in the preparation of an application for equipment authorization of model WLTGG-133 to the FCC Rules and Regulations. International Certification Corp. No.3-1, Lane 6, Wen San 3rd St. Kwei Shan Dist., TaoYuan City 333, Taiwan (R.O.C.) Name: Gary Chang Job Title : Manager e-mail : garychang@icertifi.com.tw Address :

We further certifies that neither the applicant nor any party to this application, as defined in 47 CFR Ch. 1.2002(b), is subject to a denial to Federal benefits, that include FCC benefits, pursuant to section 5301 of the Anti-Drug Abuse Act of 1998, 21 U.S.C. 862. This appointment also includes the authority to complete FCC Form 731 on our behalf and sign the application as an authorized agent. Adam Wang/ moa Engineering Dept. Gemtek Technology Co., Ltd. Tel: 886 3-598-5535*1411 Fax: 886 3-597-6663 E-mail: adam@gemteks.com