all | frequencies |
|
exhibits | applications |
---|---|---|---|---|
manual |
app s | submitted / available | |||||||
---|---|---|---|---|---|---|---|---|
1 2 |
|
Users Manual | Users Manual | 843.41 KiB | ||||
1 2 | Cover Letter(s) | |||||||
1 2 | External Photos | |||||||
1 2 | ID Label/Location Info | |||||||
1 2 | Internal Photos | |||||||
1 2 | Operational Description | |||||||
1 2 | Cover Letter(s) | |||||||
1 2 | RF Exposure Info | |||||||
1 2 | Cover Letter(s) | |||||||
1 2 | Test Report | |||||||
1 2 | Test Report | |||||||
1 2 | Test Setup Photos |
1 2 | Users Manual | Users Manual | 843.41 KiB |
Dual Radio 2.4GHz/5GHz Access Point P-720 Users Guide v1.0 Within the 5.15 to 5.25 GHz band (5GHz radio channels 34 to 48) the U-NII devices are restricted to indoor operations to reduce any potential harmful interference to MSS operations. FCC Warning FCC Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
Reorient or relocate the receiving antenna.
Connect the equipment into an outlet on a circuit different from that to which the receiver is Increase the separation between the equipment and receiver.
Consult the dealer or an experienced radio/TV technician for help. connected. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Caution Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator &
your body. If this device is going to be operated in 5.15 ~ 5.25GHz frequency range, then it is restricted in indoor environment only. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. P-720 is limited in CH1~CH11 for 2.4GHz by specified firmware controlled in U.S.A Page 1 of 51 P-720 Users Guide v1.0 Contents Jun 10, 2005 FCC Warning.......................................................................................................................................1 CONTENTS ............................................................................................................................................2 ABOUT THIS GUIDE..............................................................................................................................4 Purpose ...............................................................................................................................................4 Prerequisite Skills and Knowledge......................................................................................................4 Conventions Used in this Document ...................................................................................................4 CHAPTER 1 INTRODUCTION ............................................................................................................5 Product Overview ................................................................................................................................5 Features Highlight ...............................................................................................................................6 CHAPTER 2 - INSTALLATION ..............................................................................................................8 The Product Package..........................................................................................................................8 Hardware Introduction.........................................................................................................................8 General Overview ............................................................................................................................8 Bottom Cover...................................................................................................................................9 LEDs ................................................................................................................................................9 Connectors.....................................................................................................................................10 Connect to the Power Source and Local Network ............................................................................11 Software Installation..........................................................................................................................12 Initialization ....................................................................................................................................12 CHAPTER 3 APPLICATION MODE .................................................................................................14 AP + AP Mode...................................................................................................................................14 AP + Bridge Mode .............................................................................................................................14 CHAPTER 4 REFERENCE MANUAL...............................................................................................16 Web Interface ....................................................................................................................................16 Status ................................................................................................................................................17 Status | Device Status ...................................................................................................................17 Status | Wireless Status.................................................................................................................17 Network .............................................................................................................................................18 Network | Interface.........................................................................................................................18 Network | RADIUS Server .............................................................................................................20 Network | DHCP Settings ..............................................................................................................21 Wireless.............................................................................................................................................26 Wireless | Basic .............................................................................................................................26 Wireless | Advance ........................................................................................................................30 Wireless | WEP..............................................................................................................................35 Wireless | MAC ACL ......................................................................................................................36 System...............................................................................................................................................39 System | Security...........................................................................................................................39 System | SNMP..............................................................................................................................39 System | Telnet..............................................................................................................................41 System | Configuration ..................................................................................................................41 System | Reset...............................................................................................................................43 System | Upgrade ..........................................................................................................................43 APPENDIX............................................................................................................................................45 A) Specification .................................................................................................................................45 B) Factory Defaults for the P-720......................................................................................................46 Page 2 of 51 P-720 Users Guide v1.0 Jun 10, 2005 C) Regulatory Channels/Power ...........................................................................................46 D) Location ID and ISO Country Codes............................................................................................48 Page 3 of 51 P-720 Users Guide v1.0 Jun 10, 2005 About this Guide Purpose This document provides information and procedures on hardware installation, setup, configuration, and management of the high performance Dual Radio 2.4GHz/5GHz AP P-720. Prerequisite Skills and Knowledge To use this document effectively, you should have a working knowledge of Local Area Networking
(LAN) concepts and wireless Internet access infrastructures. In addition, you should be familiar with the following:
Hardware installers should have a working knowledge of basic electronics and mechanical assembly, and should understand related local building codes.
Network administrators should have a solid understanding of software installation procedures for network operating systems under Microsoft Windows 95, 98, Millennium, 2000, NT, and Windows XP and general networking operations and troubleshooting knowledge. Conventions Used in this Document The following typographic conventions and symbols are used throughout this document:
Very important information. Failure to observe this may result in damage. Important information that should be observed. Additional information that may be helpful but which is not required. Menu commands, buttons and input fields are displayed in bold File names, directory names, form names, and system-generated output such as error messages are displayed in constant-width type
<value> Placeholder for certain values, e.g. user inputs
[value]
Input field format, limitations, and/or restrictions. Page 4 of 51 bold code P-720 Users Guide v1.0 Jun 10, 2005 Chapter 1 Introduction Thank you for choosing the Dual Radio Access Point P-720. The P-720 operates simultaneously in the 5-GHz and 2.4-GHz frequency bands and is fully compliant to 802.11b/g and 802.11a standard with its high performance and enhanced security. The two Dual-Band radio (a/g + a/g) that this product provides supplies the furthest in flexibility and makes sure low interference and large coverage. The a+g operation mode and Multiple BSSID that this product provides differentiates it from traditional indoor AP product. Product Overview Flexibility and high performance The P-720 is a high performance indoor AP for multiple service. The two dual-band radios and AP/Bridge working mode supply the furthest flexibility for wireless applications:
Simultaneously supports 802.11a/b/g in one platform Dual AP configuration for high client density environment Dual AP configuration for supporting all kinds of client (11a/b/g) simultaneously Dual Bridge configuration for wireless repeating and wireless bridging areas
Secure and reliable wireless networking The P-720 supplies multiple methods to protect the wireless network:
Supports VLAN, up to 16 VLAN tagging IEEE 802.1x/EAP with certificates and SIM card (EAP/TLS, EAP/PEAP, EAP/SIM and EAP/TTLS) 64bits/128bits static and dynamic WEP key
WPA(TKIP and AES)
WPA2
Layer 2 Isolation for preventing snooping on the same BSS MAC ACL for preventing illegal attacking from Internet
Multiple BSSID Supports up to16 BSSID, each BSSID can be configured independently, such as Multiple SSID, security policy, authentication method, RADIUS server and VLAN tag. With this, P-720 can supply multiple services, including multiple VLAN partition and multiple security policy. Simple Installation Support IEEE 802.3af Power-over-Ethernet as well as external power supply by power adaptor. This reduces the cost and the effort of installation and maintenance dramatically. Easy remote management and maintenance Page 5 of 51 P-720 Users Guide v1.0 Jun 10, 2005 The P-720 can be remote managed by HTTPs, CLISH and SNMP.
Web-based user interface based on HTTPs and CLISH configuration based on SSHv2 supplies
secure remote management NMS product supplies the system management solution DHCP Server/DHCP Relay service supplies flexibility for different network setup Remote software upgrading via HTTPs
Management Option You can use the Access Point management systems through the following interfaces:
Web-browser interface with HTTPS
Command Line interface (CLI) with optional SSH
Simple Network Management Protocol P-720 management system pages are organized the same way for the web-browser interface and the CLI. This user manual provides detailed description of each management option. Features Highlight Super AP Multiple BSSID (up to 16)
SSID per BSSID
Enabled or Disabled Hidden SSID per BSSID
VLAN ID per BSSID
AAA way per BSSID, 802.1x and web login
Co-existence of 802.1x and web login
Security policy per BSSID
WPA pass-through
RADIUS server per BSSID AAA
RADIUS client supporting
802.1x supporting(EAP/TLS,EAP/TTLS, EAP/PEAP and EAP/SIM) Security
Static 64/128bits WEP, Dynamic 64/128bits WEP
WPA/TKIP and WPA/AES support
MAC ACL
Access Control (accept rule and deny rule) based on MAC address
Layer 2 Isolation
Hidden SSID Management
Secure management via HTTPS, CLISH, SNMP
Standard MIB
Remote firmware update via WEB UI
Backup/Restore configuration file Page 6 of 51 Jun 10, 2005 P-720 Users Guide v1.0
DHCP Server Super Brige
802.11a/b/g compliant
108Mbps raw data rate supporting
Up to 8 bridge links supporting
Special radio for Bridge
WPA/PSK over Bridge link Page 7 of 51 P-720 Users Guide v1.0 Jun 10, 2005 Chapter 2 - Installation This chapter provides installation instructions for the hardware and software components of the Access Point P-720. It also includes the procedures for the following tasks:
Hardware Introduction (LEDs, Connectors)
Connecting the Access Point
First Configuration The Product Package The product comes with the following:
Dual Radio Access Point (model: P-720)
Screw Bag for Mounting Kit
Antenna (Dual-band Dipole Antennas with TNC plug connector, 2 units)
Ethernet patch cable (Cat5 UTP, 1.8m length, 1 unit)
External power supply (Input:100-230VAC, 50-60Hz, Output: 12VDC, 1 unit)
Installation CD containing:
P-720 User Guide in PDF format
Product Firmware
Release Notes
Adobe Acrobat Readers
Readme
Printed Release Note Hardware Introduction General Overview Figure 1 P-720 General View The front panel of P-720 contains:
There are 4 indicator lights (LEDs) that help to describe the state of various networking and connection operations. The Bottom cover of P-720 contains:
Connectors which enable you to make different network connections for the device
Reset button enables you to reboot or reset the device configuration to the factory defaults Press the Reset button for less than 5 seconds to reboot the device. Press the Reset button for more than 5 seconds to set the device to factory Page 8 of 51 P-720 Users Guide v1.0 defaults. Bottom Cover 1 Jun 10, 2005 2 3 Figure 2 Bottom Cover of the P-720 The Bottom Cover of the P-720 contains:
1. Back Label with Model and Device name. The official device name is Dual Radio 2.4GHz/5GHz 2. MAC address labels of the device. The two labels show the WLAN1 and WLAN2 interface MAC Access Point, model P-720. address of the device. 3. Serial Number label of the device. LEDs The P-720 Access Point has 3 LEDs located on the front panel:
Page 9 of 51 P-720 Users Guide v1.0 Jun 10, 2005 1 2 3 4 Figure 3 LEDs of the P-720 The various states of the LEDs indicate different networking and connection operations as follows:
Item LED 1 Color Green Power LAN Green 2 3 Wireless1 4 Wireless2 Status On Blink On Blink Green
(802.11g module is functional) Amber
(802.11a module is functional) Green
(802.11g module is functional) Amber
(802.11a module is functional) On Blink On Blink On Blink On Blink Connectors The P-720 has several connectors on the rear panel:
3 1 Figure 4 RF Connectors Descriptions of the connectors are given in the following table:
4 5 Indication P-720 is active/working P-720 is booting P-720 Ethernet Port Link Active P-720 Ethernet Port is Transmitting and Receiving data P-720 WLAN1 RF card Active P-720 WLAN1 RF card is Transmitting and Receiving data P-720 WLAN1 RF card Active P-720 WLAN1 RF card is Transmitting and Receiving data P-720 WLAN2 RF card Active P-720 WLAN2 RF card is Transmitting and Receiving data P-720 WLAN2 RF card Active P-720 WLAN2 RF card is Transmitting and Receiving data 6 2 Page 10 of 51 P-720 Users Guide v1.0 Jun 10, 2005 Item Connector 1 2 3 4 WLAN1 WLAN2 Power Reset Description For WLAN1 RF card connecting to Antenna For WLAN2 RF card connecting to Antenna For power supply Reboot or reset to factory defaults. Press the reset button for less than 5 seconds to reboot the Access Point. Press the reset button for more than 5 seconds to set the Access Point to factory defaults. To your company LAN For console connection LAN Console 5 6 Connect to the Power Source and Local Network There are two power supply methods can be used by P-720:
Power-over-Ethernet equipment External Power Supply Case 1 Use the Power-over-Ethernet Equipment:
Use the enclosed power cord or any IEEE802.3af Compliant POE Power Source Devices to supply your P-720 Access Point. Step 1 Place the Access Point on a flat work surface or hang on the wall. Use the enclosed 4 screws to put the rear side of the Access Point hanging on the wall. Step 2 Connect the Ethernet cable from the P-720 route to an IEEE802.3-2003 compliant Power source Equipment. Step 3 If you use a POE HUB, please connect the P-720 LAN port to the PWR-LAN OUT port of the POE HUB and connect the LAN-IN port of the POE HUB to the Switch or hub in the local network. Figure 5 Connecting P-720 to Power source and network by PoE HUB Case 2 Use External Power Supply Page 11 of 51 P-720 Users Guide v1.0 Jun 10, 2005 Step 1 Place the Access Point on a flat work surface or hang on the wall. Step 2 Use the enclosed Ethernet patch cable to connect the LAN port of the Access Point to the Switch or hub in the local network. Step 3 Connect the power supply to the Access Point. Software Installation Initialization For the first web browser connection to your P-720, please use your Web browser The default network settings for your new access point are:
LAN port:
Step 1 IP 192.168.2.2 subnet 255.255.255.0 Configure your PC with a static IP address on the 192.168.2.0 subnet with mask 255.255.255.0. Connect the P-720 in to the same physical network as your PC. Open the Web browser and type the default IP address of the P-720:
https://192.168.2.2 Enter the P-720 administrator login details to access the Web management. The default administrator log on settings for all access point interfaces are:
User Name: admin Password: admin01 Page 12 of 51 Step 2 P-720 Users Guide v1.0 Jun 10, 2005 Step 3 After successful administrator log on you will see the main page of the P-720s Web interface:
Now you are enabled to perform your configuration. Page 13 of 51 P-720 Users Guide v1.0 Jun 10, 2005 Chapter 3 Application Mode The two Dual-Band chips (a/g + a/g) that this product provides supplies the furthest flexible application. Three application modes are supplied by P-720:
AP + AP mode
AP + Bridge mode AP + AP Mode AP + AP configuration can be for client density environment. The typical usage is: 11g AP + 11a AP. Figure 6 AP +AP application mode AP + Bridge Mode AP + Bridge configuration is for environment with last mile issue. The typical usage is: 11g AP + 11a Bridge. Page 14 of 51 P-720 Users Guide v1.0 Jun 10, 2005 Figure 7 AP +Bridge application mode Page 15 of 51 P-720 Users Guide v1.0 Jun 10, 2005 Chapter 4 Reference Manual This chapter contains web management reference information. The web management main menu consists of the following sub menus:
Status device status showing
Network device settings affecting networking
Wireless device settings related to the wireless part of the P-720
System device system settings directly applicable to the P-720
Exit click exit and leave the web management then close your web-browser window. Web Interface The main web management menu is displayed at the top of the page after successfully logging into the system (see the figure below). From this menu all essential configuration pages are accessed. Figure 8 Main Configuration Management Menu The web management menu has the following structure:
Status Device Status show the status related with the whole device Wireless Status show the status of the two radios Network Interface TCP/IP settings of P-720 LAN (Bridge) port RADIUS Server specify the settings of RADIUS server which is used by 802.1x or WPA DHCP Settings specify the settings of DHCP server or DHCP relay service Wireless Basic specify the basic settings related with wireless part Advance specify the settings of multiple BSSID or Bridge WEP specify the WEP settings related with static WEP encryption MAC ACL MAC ACL settings for P-720 System Security set access permission to your P-720 SNMP SNMP service Telnet Telnet/SSH service Configuration system configuration utilities, including Backup/Upload configuration Reset reboot device and restore systems to factory default Upgrade Upgrade the firmware remotely In the following sections, short references for all menu items are presented. Page 16 of 51 P-720 Users Guide v1.0 Jun 10, 2005 Status Status | Device Status The device status page shows important information for the P-720, its system status and network configuration. Figure 9 Device Status System Version display the current version of the firmware loaded to the AP This is important information for support requests and for preparing firmware upgrading Uptime indicates the time, expressed in days, hours and minutes since the system was last rebooted. Wlan1 MAC / Wlan 2 MAC shows the MAC addresses of the two wireless interfaces of the P-720 Free System Memory indicates the memory currently available in the P-720 Total System Memory indicates the total memory in the P-720 LAN Mode indicate static IP or DHCP client is used for P-720 LAN IP address LAN IP shows the LAN IP address of P-720 LAN Mask shows the LAN Network Mask of P-720 Gateway shows the default gateway of P-720 Status | Wireless Status The wireless status shows the information related with P-720 two wireless interfaces. Page 17 of 51 P-720 Users Guide v1.0 Jun 10, 2005 Figure 10 Wireless Status Radio1 / Radio2 relates with two wireless interfaces Channel indicates which channel is in use. Mode AP or Bridge mode is be used for this wireless interface Band specify which band is in use for wireless interface Layer2 Isolation specify the status of Layer2 Isolation service on this wireless interface Total Connected Clients indicates number of the currently connected clients to your P-720 Antenna Gain indicates antenna Gain value. Total Output Power (EIRP) indicates EIRP value set to the P-720 MAC ACL indicates the status of MAC ACL feature on P-720 Network Network | Interface The interface configured is bridge device therefore only one interface is displayed here for configuration. Bridge interface and its settings are listed in the Interface page. Page 18 of 51 P-720 Users Guide v1.0 Jun 10, 2005 Figure 11 Interface Configuration Table To change network interface (bridge) configuration properties click the Edit button in the Action column. The status can be changed now:
Figure 12 Edit Interface Configuration Settings IP Address - specify new interface IP address [in digits and dots notation, e.g. 192.168.123.70]. Netmask specify the subnet mask [[0-255].[0-255].[0-255].[0-255]].These numbers are a binary mask of the IP address, which defines IP address order and the number of IP addresses in the subnet. Gateway Address interface gateway. For Bridge type interfaces, the gateway is always the gateway router. Protocol specify static for setting IP address manually and dhcp for getting IP address dynamically acting as DHCP client. Save save the entered values. Cancel restore all previous values. Change status or leave in the default state if no editing is necessary and click the Save button. Figure 13 Apply or Discard Interface Configuration Changes Apply Changes to save all changes in the interface table at once. Discard Changes restore all previous values. For such each change of settings, the P-720 needs to be restarted to apply all settings changes when clicking Apply Changes. Request for reboot server appears:
Page 19 of 51 P-720 Users Guide v1.0 Jun 10, 2005 Figure 14 Reboot Server Reboot Click the button to restart the server and apply the changes. If there is no other setting needed to be modified, click the Reboot button for applying all modifications. And if there are still other setting modifications needed, go ahead to finish all changes and then click Reboot button to restart and apply all settings together. To reboot at once, click Reboot button and then it is necessary to wait a moment. And the message of reboot appears just like bellows:
Figure 15 Reboot Information Network | RADIUS Server Up to 32 different RADIUS servers can be configured under the RADIUS servers menu. By default, one RADIUS server is specified for the system:
Page 20 of 51 P-720 Users Guide v1.0 Jun 10, 2005 Figure 16 RADIUS Servers Settings Add add new RADIUS server. Click Add to configure RADIUS server settings. Figure 17 RADIUS Server's Details Name specify the new RADIUS server name which is used for selecting RADIUS server. Server IP authentication RADIUS server IP address [dots and digits]. Server Port specify the network port used to communicate with RADIUS [1-65535]. The port default value of 1812 is based on RFC 2138 "Remote Authentication Dial-
in User Service (RADIUS)". Secret shared secret string that is used to make sure the integrity of data frames used for authentication server. Save add new specified RADIUS server. Cancel restore all previous values. After adding a new RADIUS server or editing an existing one, the following control appears:
Edit edit an existing RADIUS server settings Delete delete an existing RADIUS server settings Reboot restart the controller to make applied changes work. If there is no other setting needed to be modified, click the Reboot button for applying all modifications. And if there are still other setting modifications needed, go ahead to finish all changes and then click Reboot button to restart and apply all settings together. Network | DHCP Settings P-720 can act as DHCP server or DHCP relay. The DHCP (Dynamic Host Configuration Protocol) service is supported on physical interfaces. Page 21 of 51 P-720 Users Guide v1.0 Jun 10, 2005 DHCP server and DHCP relay is disabled by default. Figure 18 DHCP Settings Edit edit the wireless basic settings To change DHCP setting properties click the Edit button, the DHCP server or DHCP relay service should be configured:
Figure 19 DHCP Settings Status Select status from the drop-down menu. Disabled Disable the DHCP server service. DHCP Server Enable the DHCP server service. DHCP Relay Enable the DHCP Relay service. Choose DHCP Server to enable DHCP server service. Choose DHCP Relay to enable DHCP relay service. DHCP Server This DHCP server service enables clients on the LAN to request configuration information, such as IP address, from a server. Settings of the DHCP service can be viewed just like the follow page. Figure 20 DHCP server Settings Page 22 of 51 P-720 Users Guide v1.0 Jun 10, 2005 By default, DHCP server is disabled for P-720. IP Address from / IP Address to specify the IP address range to be dynamically allocated by the DHCP server. Netmask enter the netmask for IP pool range. Gateway enter the gateway IP for wireless clients. WINS Address (Windows Internet Naming Service) specify server IP address if it is available on the network [dots and digits]. Lease Time specify the IP address lease interval in seconds [1-1000000]. DNS address specify the DNS servers IP address [in digits and dots notation]. DNS secondary address specify the secondary DNS servers IP address [in digits and dots notation]. Change status or leave in the default state if no editing is necessary and click the Save button. Figure 21 Apply or Discard DHCP server Settings The DHCP server settings will be automatically adjusted to match the network interface settings. The Gateway of DHCP server settings must be same with the Gateway of P-720 For each change of settings, the P-720 needs to be restarted to apply all settings changes when clicking Apply Changes. Request for reboot server appears:
Page 23 of 51 P-720 Users Guide v1.0 Jun 10, 2005 Figure 22 Reboot information Reboot Click the button to restart the server and apply the changes. If there is no other setting needed to be modified, click the Reboot button for applying all modifications. And if there are still other setting modifications needed, go ahead to finish all changes and then click Reboot button to restart and apply all settings together. When P-720 network Interface uses DHCP to get IP address dynamically, DHCP server service cannot be enabled. When P-720 uses DHCP to get IP address, the similar WEB UI will be appears:
Figure 23 Warning information Page 24 of 51 P-720 Users Guide v1.0 Jun 10, 2005 DHCP Relay To route DHCP through the external server, enable the DHCP Relay service. Figure 24 DHCP Relay settings Server IP: enter the IP address of the external DHCP server. Change status or leave in the default state if no editing is necessary and click the Save button. Figure 25 Apply or Discard DHCP relay Settings For each change of settings, the P-720 needs to be restarted to apply all settings changes when clicking Apply Changes. Request for reboot server appears:
Figure 26 Reboot information Reboot Click the button to restart the server and apply the changes. If there is no other setting needed to be modified, click the Reboot button for applying all modifications. And if there are still other setting modifications needed, go ahead to finish all changes and then click Reboot button to restart and apply all settings together. Page 25 of 51 P-720 Users Guide v1.0 Jun 10, 2005 Wireless Wireless | Basic Use the wireless | Basic menu to configure such wireless settings as regulatory channel, band, and power, layer2isolation. Click the edit button on the setting you need to change:
Figure 27 Basic Wireless Settings Site Survey perform survey to show overview information for wireless networks in a local geography. The site survey shows overview information for wireless networks in a local geographic area. Using this survey, administrator can scan for working access points, check their operating channels, and see RSSI levels. To start the scan, simply click the Site Survey menu. After clicking Site Survey, you will get the follow warning:
Figure 28 Site Survey warning Page 26 of 51 P-720 Users Guide v1.0 Jun 10, 2005 Click OK to continue site survey and get the similar UI:
Figure 29 Site Survey information To refresh the statistics click the Rescan button. During Site Survey, all wireless clients which are connecting with P-720 would be kicked off. Site Survey takes some minutes to perform. Please wait and dont power off AP during site survey. Edit edit the wireless basic settings To change basic wireless setting properties click the Edit button in the Action column. The status can be changed now:
Figure 30 Edit Basic Wireless Settings Change status or leave in the default state if no editing is necessary and click the Save button. Page 27 of 51 P-720 Users Guide v1.0 Jun 10, 2005 Figure 31 Apply or Discard Basic Wireless Settings Radio specify which wireless interface of P-720 is shown Channels select the channel that the access point will use to transmit and receive information. If one channel is defined, it acts as default channel. Channels list will vary depending on selected regulatory selected band. Multiple frequency channels are used to avoid interference between two radios of this AP, and between nearby access points. If you wish to operate more than one access point in overlapping coverage areas, we recommend a distance of at least four channels between the chosen channels. For example, for three Access Points in close proximity choose channels 1, 6 and 11 for 11b/g or channels 36, 40 and 64 for 11a. Band working bands on which your radios are working. Six bands are supplied: 5GHz(11a), 5GHz(Turbo Mode 11a), 2.4GHz(Mixed 11g), 2.4GHz(11g only), 2.4GHz(Mixed 11g WiFi) and 2.4GHz(11g only WiFi). If 2.4GHz(Mixed 11g) or 2.4GHz(11g only) is selected, the radio will work on 2.4GHz for a better performance. 2.4GHz (11g only) mode only allows 11g client access. 2.4GHz(Mixed 11g) mode allows 11b/11g client access. 2.4GHz(Mixed 11g WiFi) or 2.4GHz(11g only WiFi) can make sure to compatible with Wi-Fi. If 5GHz (11a) or 5GHz(Turbo Mode 11a) is selected, the radio will work on 5GHz 11A mode. 5GHz(Turbo Mode 11a) can supply 108 raw data rate. Only under Bridge mode, Turbo Mode 11a can be set. Page 28 of 51 P-720 Users Guide v1.0 Jun 10, 2005 Total Output Power (EIRP) the P-720 transmission output power (EIRP) in dBm. Seven levels are specified: 17dBm, 16dBm, 15dBm, 14dBm, 10dBm, 4dBm and 0dBm. Default is 14dBm. Total Output Power (EIRP) = Antenna Gain + RF card output power The range of the EIRP varies with channel. RTS Threshold when set, this settings specifies the maximum packet size beyond which RTS/CTS mechanism is be invokes. The value range of this is [0 2347]. Default is 2347 which means that RTS is disabled. Layer 2 Isolation Layer2 wireless client separation. Connected clients with user isolation function enabled cannot access each other directly. The clients are isolated from each other using their MAC addresses [enabled/disabled]. Mode two modes are supplied: AP mode and Bridge mode. For such each change of settings, the P-720 needs to be restarted to apply all settings changes when clicking Apply Changes. Request for reboot server appears:
Figure 32 Reboot Server Reboot Click the button to restart the server and apply the changes. If there is no other setting needed to be modified, click the Reboot button for applying all modifications. And if there are still other setting modifications needed, go ahead to finish all changes and then click Reboot button to restart and apply all settings together. Page 29 of 51 P-720 Users Guide v1.0 Jun 10, 2005 Wireless | Advance P-720 supports Multiple BSSID (MBSSID) function. You can configure up to 16 BSSIDs per radio on P-720 and assign different configuration settings to each BSSID. For wireless users, they can think P-
720 as single AP with multi service supporting, including different security policy, different VLAN ID, different authentication etc. All the BSSIDs are active at the same time that means client devices can associate to the access point for specific service. Use the Wireless | Advance menu to configure properties related to Multiple BSSID, including configure SSID, Hidden SSID, VLAN, and Security for each SSID. Each BSSID can have its own SSID. In this case, Multiple BSSID is the same with Multiple ESSID. Wireless users can think P-720 as multiple virtual APs, each supporting different service, and connects one SSID for the special services. Also, P-720 supports Bridge function, it can support up to 8 Bridge links per radio. Different bridge link can use different WEP key index. AP Mode:
Figure 33 Advanced Wireless Setting (AP Mode) Radio specify which RF card (wlan1 or wlan2) is needed to be configured since P-720 has two Dual-Band radios Mode specify the operation mode of P-720 (AP or Bridge) Interface Choose the specified MBSSID entry you want to configure. Each Interface maps to a BSSID Hidden Show the status of Hidden SSID feature Security Show which security policy is used for this MBSSID entry Current Connect # Show the number of current wireless clients who are connecting with this MBSSID New Create a new MBSSID entry Detail Show the detail information of this MBSSID entry Edit Edit the selected MBSSID entry you want to configure Delete Delete the selected MBSSID entry. When in AP mode, you can not delete the last entry Clicking Detail, a similar page will be appears as below:
Page 30 of 51 P-720 Users Guide v1.0 Jun 10, 2005 Figure 34 Detail for MBSSID entry Detail Show the MAC address of current connected clients Return Return to the wireless advance settings page Clicking New or Edit on AP mode, the settings of MBSSID entry appears:
Page 31 of 51 P-720 Users Guide v1.0 Jun 10, 2005 Figure 35 Multiple BSSID Setting Radio showing which RF card (wlan1 or wlan2) is being configured. Mode showing the current operation mode of P-720 (AP or Bridge). Interface showing the current MBSSID | Bridge link entry SSID a unique ID for your wireless network. It is case sensitive and must not exceed 32 characters. The default SSID is "P-720" but you should change this to a personal wireless network name. The SSID is important for clients when connecting to the access point. All client stations must have their client SSID settings configured and must use the same SSID. Each MBSSID entry (BSSID) can has its own SSID. And SSID can be same for different BSSID Hidden SSID When enabled, the SSID of this Interface is invisible in the networks list while scanning the available networks for wireless client (SSID is not broadcasted with its Beacons). When disabled, the APs SSID is visible in the available network list [enabled/disabled]. By default the Hidden SSID is disabled. Use VLAN When enabled, the outgoing packets from this SSID device will be tagged with VLAN ID and 802.1p tag (If have). VLAN ID Configure VLAN ID for each Multiple SSID devices. Valid numbers are from 1 to 4094. Page 32 of 51 P-720 Users Guide v1.0 Jun 10, 2005 802.1p Tag Configure 802.1p Tag for remote APCs or Routers QoS uses. Valid numbers are from 0 to 7. VLAN ID and 802.1p tag must cooperate with remote Router or APC. Security Specify the security policy. WEP When selected, the privacy of MSSID entry will be set to WEP (Wired Equivalent Privacy). WEP Key Index Select the default key Index to make it the Default key and encrypt the data before being transmitted. All stations, including this MSSID Entry, always transmit data encrypted using this Default Key. The key number (1,2,3,4) is also transmitted. The receiving station will use the key number to determine which key to use for decryption. If the key value does not match with the transmitting station, the decryption will fail. The key value is set in Wireless | WEP web page. 802.1x When selected, the MSSID entry will be configured as an 802.1x authenticator. It supports multiple authentication types based on EAP (Extensible Authentication Protocol) like EAP-TLS, EAP-TTLS, EAP-PEAP, EAP-SIM. The privacy will be configured as dynamic WEP. RADIUS Server Profile Select the default radius server name. If not, please configure Network | RADIUS Servers Web page first. Dynamic Key Length Select the dynamic 64-bits / 128-bits encryption. WPA Wi-Fi Protected Access, When selected, the encrypt method will be WPA with RADIUS Sever. RADIUS Server Profile The same as 802.1x. Algorithm Choose WPA algorithm (TKIP, AES). Use ReKey If not selected, indicates that Group Key will not be rekeyed. If selected, must specify the time in minutes, after which the group key will be updated. Every minutes Specify amount of minutes and WPA automatically will generate a new Group Key. WPA-PSK When selected, the encrypt method will be WPA without RADIUS Server. Use Pre-Shared Key Specify more than 8 characters and less than 64 characters for WPA with pre-shared key encryption. Algorithm The same as WPA. Use Rekey The same as WPA. Every minutes The same as WPA. MAC Auth MAC authentication. When selected, the MAC address of username and password will be passed to RADIUS server for PAP authentication when wireless client connects with P-720. RADIUS Server Profile The same as 802.1x. Disabled When selected, you dont select any security policy. Bridge Mode Page 33 of 51 P-720 Users Guide v1.0 Jun 10, 2005 Figure 36 Advanced Wireless Setting (Bridge Mode) Radio specify which RF card (wlan1 or wlan2) is needed to be configured since P-720 has two Dual-Band radios Mode specify the operation mode of P-720 (AP or Bridge) Interface Choose the specified Bridge link entry you want to configure. Remote MAC Specify the remote peers MAC address of this Bridge Security Specify which security policy is used New Create a new Bridge link entry Detail Show the detail information of this Bridge link entry Edit Edit the selected Bridge link entry you want to configure Delete Delete the selected Bridge link entry. Clicking Detail, the similar page will be appears:
Figure 37 Detail of one bridge entry Clicking Edit for editing an existed bridge link or New for adding a new bridge link, you can see the figure like this. Page 34 of 51 P-720 Users Guide v1.0 Jun 10, 2005 Figure 38 Bridge Link Setting Remote MAC Add the remote peers MAC address you want to configure as a bridge link Security Specify WEP or WPA-PSK (TKIP or AES) is used for security policy. WPA-PSK or static WEP can be used for encrypt each bridge link Each Bridge link can have its own WEP key/keyIndex for encryption. Only WEP can be used as security policy for Bridge links now. More enhanced security policy is in developing. By default, four WEP keys are all set to aaaaa. They can be modified in Wireless | WEP. Wireless | WEP Use the Wireless | WEP menu to configure static WEP settings. This menu only set static WEP key value related with 4 key indexes for each RF card (wlan1 or wlan2). Enable or Disable static WEP is in the Wireless | Advance menu. Figure 39 WEP Settings Page 35 of 51 P-720 Users Guide v1.0 Jun 10, 2005 Radio specify which RF card (wlan1 or wlan2) is needed to be set. Click Edit to edit the existing wepkey1 to wepkey4. By default, four WEP keys are all set to aaaaa. They can be modified according to real need. Figure 40 Edit WEP Key Wireless | MAC ACL Use the MAC ACL service to control the default access to the wireless interface of the P-720 or define special access rules for mobile clients. Configure the ACL using the Wireless | MAC ACL menu:
Figure 41 MAC ACL Service Radio Two wireless interfaces wlan1 and wlan2 can be selected for each radios MAC ACL rules. Only AP mode has the MAC ACL service. The wireless interface whose mode is Bridge hasnt MAC ACL settings. Policy Setting click the edit button to choose Allow, Deny or disable the access control service on device. By default the ACL service is disabled and all wireless clients connecting to the P-720 are allowed (no ACL rules are applied to the wireless clients). Select Allow means only the wireless clients whose MAC are listed in the MAC List would be permitted to access this AP. Other wireless client cannot access this AP. Select Deny means only the wireless clients whose MAC are listed in the MAC List would be prevented from accessing. Other wireless clients can access this AP. Page 36 of 51 P-720 Users Guide v1.0 Jun 10, 2005 Select Disabled means no ACL service. Figure 42 MAC ACL settings You must create MAC List to work with Policy setting. The access control list is based on the network devices MAC address. In the MAC ACL Configuration table, you only need to specify the MAC address of wireless client. Click the Add button to create a new MAC entry:
Figure 43 Add MAC entry MAC Address enter the physical address of the network device you need to (MAC address) The format is a list of colon separated hexadecimal numbers (for example: 00:AA:A2:5C:89:56). Save click the button to save the new MAC entry. Figure 44 Apply or Discard MAC ACL Configuration Changes Apply Changes to save all changes made in the interface table at once. Discard Changes restore all previous values. For such each change of settings, the P-720 needs to be restarted to apply all settings changes when clicking Apply Changes. Request for reboot server appears:
Page 37 of 51 P-720 Users Guide v1.0 Jun 10, 2005 Figure 45 Reboot Server Reboot Click the button to restart the server and apply the changes. If there is no other setting needed to be modified, click the Reboot button for applying all modifications. And if there are still other setting modifications needed, go ahead to finish all changes and then click Reboot button to restart and apply all settings together. Page 38 of 51 P-720 Users Guide v1.0 Jun 10, 2005 System System | Security Use the System | Security service to configure the name and password administrator:
Figure 46 system security settings User Name administrator username for access to P-720 (e.g. web interface, CLI mode) [1-32 symbols, spaces not allowed]. Old Password old password value. New Password new password value used for user authentication in the system [4-8 characters, spaces not allowed]. Confirm Password re-enter the new password to verify its accuracy. Save click to save new administrator settings. Default administrator logon settings are:
User Name: admin Password: admin01 Password length is from 4 to 8 characters. System | SNMP SNMP is the standard protocol that regulates network management over the Internet. To communicate with SNMP manager you must set up the same SNMP communities and identifiers on both ends: manager and agent. Use the System | SNMP menu to change current SNMP configuration. Page 39 of 51 P-720 Users Guide v1.0 Jun 10, 2005 Figure 47 SNMP settings Readonly community Community name is used in SNMP version 1 and version 2c. Read-only
(public) community allows reading values, but denies any attempt to change values [1-32 all ASCII printable characters, no spaces]. Readwrite community Community name is used in SNMP version 1 and version 2c. Read-write
(private) community allows to read and (where possible) change values [1-32 all ASCII printable characters, no spaces]. Default Trap community The default SNMP community name used for traps without specified communities. The default community by most systems is "public". The community string must match the community string used by the SNMP network management system (NMS) [1-32 all ASCII printable characters, no spaces]. Trap Configuration Table:
You can configure your SNMP agent to send SNMP Traps (and/or inform notifications) under the defined host (SNMP manager) and community name (optional). Figure 48 SNMP Trap table settings Click Add to add a new SNMP manager or Delete to delete a specific SNMP manager. Clicking Add:
Figure 49 Add SNMP Trap Host IP enter SNMP manager IP address [dots and digits]. Host Port enter the port number the trap messages should be send through [number]. Trap Type select trap message type [v1/v2/inform]. Community specify the community name at a SNMP trap message. This community will be used in trap messages to authenticate the SNMP manager. If not defined, the default trap community name will be used (specified in the SNMP table) [1-32 all ASCII printable characters, no spaces]. Save save all current settings Cancel restore the last settings Page 40 of 51 P-720 Users Guide v1.0 Jun 10, 2005 System | Telnet Use System | Telnet menu to manage the telnet/SSH service of your P-720. Figure 50 System Configuration settings Telnet Service Enable or disable telnet service of P-720 SSH Service Enable or disable SSH service of P-720. The default of these two services are all Enabled. The current IETF SSH (SSHv2) is supported for security of accessing P-720 via telnet/CLISH. System | Configuration Use the System | Configuration menu to configure such system utilities:
Backup download current working system configuration for backup
Upload/Restore upload system configuration for restore Figure 51 System Configuration settings You can save your current device configuration file locally using the Backup menu under the System
| Configuration | Backup menu:
Figure 52 Backup settings Such device configuration is saved in the specific format file (.cfg). Description Message shows the current version of firmware. Click the Preparation button to start saving the configuration file. Click the Download button to download current working configuration into your local PC. Page 41 of 51 P-720 Users Guide v1.0 Jun 10, 2005 Figure 53 Download system configuration You can upload saved configuration file any time you want to restore this configuration to the device by using the Browse button Select the configuration file and upload it on the device:
Figure 54 Configuration Upload/Restore Click Upload for upload the specified configuration and then the similar UI appears Figure 55 configuration information HOST IP show the IP address in the configuration file that needs to upload. Please remember this IP address for accessing P-720 after the configuration file is uploaded. HOST VERSION show the firmware version in the configuration file that needs to upload. OK click the button to apply configuration setting to the device. If everything is right, click OK button for upload/restore. Page 42 of 51 P-720 Users Guide v1.0 System | Reset Jun 10, 2005 Figure 56 System Reset setting Reboot Reboot the device Reset Reset System to Factory Defaults To reboot the device, click Reboot and then the below appears to make sure:
Figure 57 Reboot the device To reset device to factory defaults, click Reset on Figure 56 and then the below appears to make sure:
Figure 58 Reset the device Please note that all settings including the administrator settings will be set back to the factory default when Reset is selected. System | Upgrade Upload Update your device firmware. Page 43 of 51 P-720 Users Guide v1.0 Jun 10, 2005 Figure 59 Firmware Upgrade Click the Upload and then the follow appears. Specify the full path to the new firmware image and click the Upload button:
Figure 60 Firmware Upgrade To flash the uploaded firmware image to upgrade the firmware is done by click the Upgrade button. Please make sure the firmware is correct for P-720. Otherwise the upgrade will be failed. Figure 61 Device Statistics Do not switch off and do not disconnect the P-720 from the power supply during the firmware update process because the device could be damaged. It is best to use the Ethernet connection (not wireless) for the firmware update process. Page 44 of 51 Jun 10, 2005 P-720 Users Guide v1.0
Appendix A) Specification Wireless Standard Data Rate Transmit Power
(adjustable RF power) Antennas Encryption Bridge Interface LAN Console Management Interfaces Software Update Restore default Physical Specification Dimension Weight Environment Specification Operating Power Supply POE Power adaptor LEDs 4 LEDs Warranty 1 years Package Contents
P-720 Dual Radio 2.4GHz/5GHz Access Point
Printed Release note
Antenna International power supply IEEE 802.11b(DSSS), IEEE 802.11g(OFDM) and IEEE 802.11a(OFDM) 802.11a: 54,48,36,24,18,12,9,6Mbps;802.11g:
54,48,36,24,12,9,6,11,5,5,2,1Mbps (auto fall back) Turbo 802.11a: 108Mbps Max. 17 dBm 1.5dBm @6~24Mbps Max. 13 dBm 1.5dBm @54Mbps (Maximum power will vary by channel, rate) 2 Dual-band Dipole Antennas with reverse: R-TNC plug connector WPATKIP and CCMP-AES, Dynamic/static 64bits and 128bits WEP Up to 8 bridge links 10/100Mb Ethernet, auto sensing, RJ-45 1DB-9 Male (RS232) for serial configuration HTTPs, Secure Telnet(SSHv2), SNMP Remote software update via HTTPs H/W and S/W remote restore factory default 195 mm x 160 mm x 27 mm 500g Temperature 0 to 50C Humidity 95%, non-condensing 48V, IEEE802.3af-2003 compliance External power supply, input: 100-230 VAC, 50-60Hz and output: 12VDC Power, LAN, WLAN1, WLAN2
CD-ROM with User Manuals (*.pdf)
Ethernet patch cable (1.8m)
Console
Mount kit package Page 45 of 51 P-720 Users Guide v1.0 Jun 10, 2005 B) Factory Defaults for the P-720 General Configuration Settings Administrator Username Administrator Password Get Community Set Community Network Configuration Settings IP address Subnet mask Gateway Wireless Configuration Settings RF Card 1(WLAN1) Default Mode SSID Default channel RTS Threshold RF Output Power Authentication Type Encryption RF Card 2(WLAN2) Default Mode SSID Default channel RTS Threshold RF Output Power Authentication Type Encryption admin admin01 Public Private
(static IP) 192.168.2.2 255.255.255.0 0.0.0.0 11g Access Point P-720 11 2347 bytes 14dBm Open System Off 11a Access Point P-720 60 2347 bytes 17dBm Open System Off C) Regulatory Channels/Power Channels and Maximum output power for the P-720 11g radio:
Channels Identifiers USA, Canada
(FCC) Frequency in MHz European Union
(CE/ETSI) Japan
(TELEC) Page 46 of 51 2412 2417 2422 2427 2432 2437 2442 2447 1 2 3 4 5 6 7 8 P-720 Users Guide v1.0 9 10 11 12 13 14 2452 2457 2462 2467 2472 2484 Maximum output Power 18.5dBm 14dBm Jun 10, 2005 14dBm For channel 1 and channel 11, the maximum output power will be 18.5dBm in the case of the setting of FCC. Channels and Maximum power for the P-720 11a radio:
Channels Identifiers USA, Canada
(FCC) Frequency in MHz European Union
(CE/ETSI) Japan
(TELEC) U-NII lower band (5150 5250 MHz) 34 36 38 40 42 44 46 48 5170 5180 5190 5200 5210 5220 5230 5240 Maximum Output Power 52 56 60 64 5260 5280 5300 5320 17dBm 17 dBm U-NII middle band (5250 5350 MHz) Maximum Output Power 17 dBm 17 dBm U-NII upper band ( 5725 5875 MHz) 149 153 157 161 165 5745 5765 5785 5805 5825 Maximum Output Power 17 dBm 17 dBm 15 dBm Page 47 of 51 P-720 Users Guide v1.0 Jun 10, 2005 D) Location ID and ISO Country Codes This list states the country names (official short names in English) in alphabetical order as given in ISO 3166-1 and the corresponding ISO 3166-1-alpha-2 code elements. It lists 239 official short names and code elements. Location ID AF AL DZ AS AD Afghanistan Albania Algeria American Samoa Andorra Location ID LI LT LU MO MK Country Country Liechtenstein Lithuania Luxembourg Macao Macedonia, the former Yugoslav republic of Madagascar Malawi Malaysia Maldives Mali Malta Marshall islands Martinique Mauritania Mauritius Mayotte Mexico Micronesia, federated states of Moldova, republic of Monaco Mongolia Montserrat Morocco Mozambique Myanmar Namibia Nauru Nepal Netherlands Netherlands Antilles New Caledonia New Zealand Nicaragua Page 48 of 51 Angola Anguilla Antarctica Antigua and Barbuda Argentina Armenia Aruba Australia Austria Azerbaijan Bahamas Bahrain Bangladesh Barbados Belarus Belgium Belize Benin Bermuda Bhutan Bolivia Bosnia and Herzegovina Botswana Bouvet island Brazil British Indian ocean territory Brunei Darussalam Bulgaria MG MW MY MV ML MT MH MQ MR MU YT MX FM MD MC MN MS MA MZ MM NA NR NP NL AN NC NZ NI AO AI AQ AG AR AM AW AU AT AZ BS BH BD BB BY BE BZ BJ BM BT BO BA BW BV BR IO BN BG P-720 Users Guide v1.0 Jun 10, 2005 NE Burkina Faso NG Burundi NU Cambodia NF Cameroon MP Canada NO Cape Verde OM Cayman islands PK Central African republic PW Chad PS Chile PA China PG Christmas island PY Cocos (keeling) islands PE Colombia PH Comoros PN Congo Congo, the democratic republic of the PL PT Cook islands Costa Rica PR QA Cte d'ivoire RE Croatia Cuba RO RU Cyprus RW Czech republic Denmark SH KN Djibouti LC Dominica Dominican republic PM VC Ecuador WS Egypt El Salvador SM ST Equatorial guinea SA Eritrea Estonia SN SC Ethiopia SL Falkland islands (malvinas) Faroe islands SG SK Fiji SI Finland France SB SO French Guiana Niger Nigeria Niue Norfolk island Northern Mariana islands Norway Oman Pakistan Palau Palestinian territory, occupied Panama Papua new guinea Paraguay Peru Philippines Pitcairn Poland Portugal Puerto Rico Qatar Runion Romania Russian federation Rwanda Saint Helena Saint Kitts and Nevis Saint Lucia Saint Pierre and Miquelon Saint Vincent and the grenadines Samoa San Marino Sao tome and Principe Saudi Arabia Senegal Seychelles Sierra Leone Singapore Slovakia Slovenia Solomon islands Somalia Page 49 of 51 BF BI KH CM CA CV KY CF TD CL CN CX CC CO KM CG CD CK CR CI HR CU CY CZ DK DJ DM DO EC EG SV GQ ER EE ET FK FO FJ FI FR GF P-720 Users Guide v1.0 Jun 10, 2005 French Polynesia French southern territories Gabon Gambia Georgia Germany Ghana Gibraltar Greece Greenland Grenada Guadeloupe Guam Guatemala Guinea Guinea-Bissau Guyana Haiti Heard island and McDonald islands Holy see (Vatican city state) Honduras Hong Kong Hungary Iceland India Indonesia Iran, Islamic republic of Iraq Ireland Israel Italy Jamaica Japan Jordan Kazakhstan Kenya Kiribati Korea, democratic people's republic of Korea, republic of Kuwait ZA GS ES LK SD SR SJ SZ SE CH SY TW TJ TZ TH TL TG TK TO TT TN TR TM TC TV UG UA AE GB US UM UY UZ VU VE VN VG VI WF South Africa South Georgia and the south sandwich islands Spain Sri Lanka Sudan Suriname Svalbard and Jan Mayan Swaziland Sweden Switzerland Syrian Arab republic Taiwan, province of china Tajikistan Tanzania, united republic of Thailand Timor-leste Togo Tokelau Tonga Trinidad and Tobago Tunisia Turkey Turkmenistan Turks and Caicos islands Tuvalu Uganda Ukraine United Arab emirates United kingdom United states United states minor outlying islands Uruguay Uzbekistan Vanuatu Vatican city state see holy see Venezuela Viet nam Virgin islands, British Virgin islands, u.s. Wallis and Futuna Page 50 of 51 PF TF GA GM GE DE GH GI GR GL GD GP GU GT GN GW GY HT HM VA HN HK HU IS IN ID IR IQ IE IL IT JM JP JO KZ KE KI KP KR KW P-720 Users Guide v1.0 Jun 10, 2005 KG LA LV LB LS LR LY Kyrgyzstan Lao people's democratic republic Latvia Lebanon Lesotho Liberia Libyan Arab Jamahiriya EH YE YU ZM ZW Western Sahara Yemen Yugoslavia Zaire see Congo, the democratic republic of the Zambia Zimbabwe Page 51 of 51
frequency | equipment class | purpose | ||
---|---|---|---|---|
1 | 2005-07-20 | 5150 ~ 5350 | NII - Unlicensed National Information Infrastructure TX | Original Equipment |
2 | 5725 ~ 5850 | DTS - Digital Transmission System |
app s | Applicant Information | |||||
---|---|---|---|---|---|---|
1 2 | Effective |
2005-07-20
|
||||
1 2 | Applicant's complete, legal business name |
Gemtek Technology Co., Ltd.
|
||||
1 2 | FCC Registration Number (FRN) |
0005801899
|
||||
1 2 | Physical Address |
No.15-1 Zhonghua Road
|
||||
1 2 |
Hukou Hsinchu, N/A 303
|
|||||
1 2 |
Taiwan
|
|||||
app s | TCB Information | |||||
1 2 | TCB Application Email Address |
i******@ckccertification.com
|
||||
1 2 | TCB Scope |
A4: UNII devices & low power transmitters using spread spectrum techniques
|
||||
app s | FCC ID | |||||
1 2 | Grantee Code |
MXF
|
||||
1 2 | Equipment Product Code |
AP940422AG
|
||||
app s | Person at the applicant's address to receive grant or for contact | |||||
1 2 | Name |
A**** W********
|
||||
1 2 | Title |
Manager
|
||||
1 2 | Telephone Number |
886 3******** Extension:
|
||||
1 2 | Fax Number |
886 3********
|
||||
1 2 |
A******@gemteks.com
|
|||||
app s | Technical Contact | |||||
1 2 | Firm Name |
Advance Data Technology Corporation
|
||||
1 2 | Name |
C******** C******
|
||||
1 2 | Physical Address |
No. 19, Hwa Ya 2nd Rd., Kwei Shan Hsiang
|
||||
1 2 |
Taoyuan Hsien, 333
|
|||||
1 2 |
Taiwan
|
|||||
1 2 | Telephone Number |
886-3******** Extension:
|
||||
1 2 | Fax Number |
886-3********
|
||||
1 2 |
C******@adt.com.tw
|
|||||
app s | Non Technical Contact | |||||
1 2 | Firm Name |
Advance Data Technology Corporation
|
||||
1 2 | Name |
S**** H********
|
||||
1 2 | Physical Address |
No. 19, Hwa Ya 2nd Rd., Kwei Shan Hsiang
|
||||
1 2 |
Taoyuan Hsien, 333
|
|||||
1 2 |
Taiwan
|
|||||
1 2 | Telephone Number |
886-3******** Extension:
|
||||
1 2 | Fax Number |
886-3********
|
||||
1 2 |
s******@adt.com.tw
|
|||||
app s | Confidentiality (long or short term) | |||||
1 2 | Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
1 2 | Long-Term Confidentiality Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | No | ||||
if no date is supplied, the release date will be set to 45 calendar days past the date of grant. | ||||||
app s | Cognitive Radio & Software Defined Radio, Class, etc | |||||
1 2 | Is this application for software defined/cognitive radio authorization? | No | ||||
1 2 | Equipment Class | NII - Unlicensed National Information Infrastructure TX | ||||
1 2 | DTS - Digital Transmission System | |||||
1 2 | Description of product as it is marketed: (NOTE: This text will appear below the equipment class on the grant) | Dual Radio 2.4GHz/5GHz Access Point | ||||
1 2 | Related OET KnowledgeDataBase Inquiry: Is there a KDB inquiry associated with this application? | No | ||||
1 2 | Modular Equipment Type | Does not apply | ||||
1 2 | Purpose / Application is for | Original Equipment | ||||
1 2 | Composite Equipment: Is the equipment in this application a composite device subject to an additional equipment authorization? | Yes | ||||
1 2 | Related Equipment: Is the equipment in this application part of a system that operates with, or is marketed with, another device that requires an equipment authorization? | No | ||||
1 2 | Grant Comments | Power Output listed is conducted. Only the antenna(s) tested in this filing may be used with the transmitter. The use of an antenna other than shown in the filing requires a PC2. The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. End -users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. Operations in the 5.15-5.25GHz band are restricted to indoor usage only. | ||||
1 2 | Power Output listed is conducted. Only the antenna(s) tested in this filing may be used with the transmitter. The use of an antenna other than shown in the filing requires a PC2. The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. End -users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. | |||||
1 2 | Is there an equipment authorization waiver associated with this application? | No | ||||
1 2 | If there is an equipment authorization waiver associated with this application, has the associated waiver been approved and all information uploaded? | No | ||||
app s | Test Firm Name and Contact Information | |||||
1 2 | Firm Name |
Bureau Veritas CPS (H.K.) Ltd. Taoyuan Branch
|
||||
1 2 | Name |
R**** C****
|
||||
1 2 | Telephone Number |
886-3******** Extension:
|
||||
1 2 | Fax Number |
886-3********
|
||||
1 2 |
r******@tw.bureauveritas.com
|
|||||
Equipment Specifications | |||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
1 | 1 | 15E | 28 CC | 5150.00000000 | 5350.00000000 | 0.0640000 | |||||||||||||||||||||||||||||||||||
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
2 | 1 | 15C | 28 CC | 2412 | 2462 | 0.101 | |||||||||||||||||||||||||||||||||||
2 | 2 | 15C | 28 CC | 5725 | 5850 | 0.071 |
some individual PII (Personally Identifiable Information) available on the public forms may be redacted, original source may include additional details
This product uses the FCC Data API but is not endorsed or certified by the FCC