FCC ID: MXF-WLRGFM100 IOT Femto Gateway

Document Number Created By Eric GIoT Femto Cell User Guide Modification History Date Change log 2017/3/23 1st version Author Revision Eric, Joey 001 This GIoT Femto Cell User Guide will assist you in navigating the system with the following comprehensive guidelines. 1. Open Admin GUI Connect to Femto Cell via wifi (SSID: AP-last 6 numbers of mac address) Access Femto Cell WebUI via IP address 192.168.55.1. Default username is admin and password is "admin. Figure 1 2. Status The Status menu consists of the following categories: Overview, Routes, System Log, Kernel Log, Processes and Realtime Graphs. An introduction of each category will be distinctly stated in individual paragraphs. 2.1 Status - Overview The purpose of this category is to view the following contents: system status, memory usage and network settings. The contents are exhibited in one single page. Please scroll down the Status page to obtain an overall view. (figure2.A & figure 2.B & figure 2.C) 1 An AUTO REFRESH ON/OFF button is lodged on the top right of the panel. This function enables the status data to be refreshed every 5 seconds.

(figure3.A & figure3.B) Figure 2.A - System Status Figure 2.B - Memory Usage and Network Settings Figure 3.A - Status will auto refresh in 5 secs if Auto Refresh ON button is on 2 Figure 3.B - Click AUTO REFRESH ON/OFF button to enable/ disable auto refresh. 2.2 Status - Routes The purpose of this category is to view the ARP table and active IPv4 routes information. Figure 4 - ARP table and Active IPv4 Routes 3 Status - System Log 2.3 This category is to view system log information. Figure 5 - System Log 4 2.4 This category is to view kernel log information. Figure 6 - Kernel Log Status - Kernel log Status - Processes 2.5 The purpose of this category is to view the system processes that are in progress. Processes can be hung up, terminated, and killed for each indivFemto Cellal item. Figure 7 - Processes 5 Status - Realtime Graphs 2.6 This category is further divided into the following sectors: Load, Traffic, and Connections. These options are lodged and labeled above the graph. 2.6.1 Load Figure 8 - Realtime Load To view the current load value and average of different time intervals. 2.6.2 Traffic To view the network traffic of each interface. Figure 9 - Realtime Traffic 6 2.6.3 Connections Figure 10 - Realtime Connections To view the currently active network connections. 3. GIoT The GIoT menu consists of the following categories: Status, Provision, Configuration and GPS MAP. 3.1 GIoT - Status The purpose of this category is to view GIoT information as in its provision code, gateway type, gateway ID or LoRa modules, channels, spreading factor, and GPS status. Figure 11 - GIoT Info 7 3.2 GIoT - Provision GIoT provision code can be setup on this page. Figure 12 - Provision Code 8 3.3 GIoT - Configuration Click PERFORM RESTART button to restart LoRa server. The latitude and longitude coordinates can be manually embedded in this page. Click SAVE LOCATION button after inserting the coordinates or click SELECT ON MAP button to be redirected to the map in GPS Settings. Figure 13 - GIoT Management 3.4 GIoT - GPS MAP To setup the GPS location, simply input your address location in the Location text field above the map or pinpoint your location on the map by dragging the red marker to the correct spot. Once the location is confirmed, the system will verify and apply the new Latitude/Longitude coordinates into its GPS setting. Figure 14 - GPS Setting 9 10 LoRaWan 4. The LoRaWan menu consists of the following categories: OTAA Status, OTAA, ABP and Network Server. The proper provision code has to be in place to reveal and access the LoRaWan features on the system menu. Please contact GIoT personnel if needed. 4.1 LoRaWan - OTAA Status The purpose of this feature is to view the process status of a node joining Femto Cell via OTAA. Figure 15 - OTAA Status 4.2 LoRaWan - OTAA Click ADD button to create an OTAA rule entry. To delete entries, select one or more OTAA rule entries and click DELETE button. To edit an entry, select a rule entry and click EDIT button to proceed. Please note that 1. The OTAA settings will be cleared after Femto Cell is reset to default. 2.The Aging Out Time must be at least 60 minutes. Figure 16.A - OTAA - Add 11 Figure 16.B - OTAA Figure 16.C - OTAA - Edit 4.3 LoRaWan - ABP 12 The main function of this feature is to add/delete/edit ABP rule entries on this page. The ABP menu consists of the following categories: Individual and NetID Group. 4.3.1 INDIVIDUAL Click INDIVIDUAL button to enter the INDIVIDUAL function page. Click ADD button to create an ABP (INDIVIDUAL) rule entry. To delete rule entries, select one or more ABP (INDIVIDUAL) rule entries and click DELETE button. To edit a rule entry , select an ABP (INDIVIDUAL) rule entry and click EDIT button to proceed. Please note that the ABP (INDIVIDUAL) settings will be cleared after Femto Cell is reset to default. 13 Figure 17.A - Individual Figure 17.B - Individual Add Figure 17.C - Individual Edit 4.3.2 NETID GROUP Click NETID GROUP button to enter NETID GROUP function page. Click ADD button to create a ABP (NETID GROUP) rule entry. To delete rule entries, select one or more ABP (NETID GROUP) rules and click DELETE button. 14 To edit a rule entry, select a ABP (NETID GROUP) rule entry and click EDIT button to proceed. Please note that the ABP (NETID GROUP) settings will be cleared after Femto Cell is reset to default. 15 Figure 18.A - NETID GROUP Figure 18.B - NETID GROUP - ADD Figure 18.C - NETID GROUP - EDIT 4.4 LoRaWan - Network Server The user can configure Network Server settings on this page. The Femto Cell connects to the lora data center via CURL or MQTT. Note that the node data will be sent to Gemtek lora data center if you select CURL. Figure 19 - Network Server 16 17 System 5. The System menu consists of the following categories: System, Administration, Backup, System Firmware, Reboot. Introduction and input procedures for each category are described in the following paragraphs. 5.1 System - System Hostname and Timezone can be customized in the system properties. Click Sync with Browser button (figure20.A) to adjust the local time. Place a checkmark next to Enable NTP Client (figure20.B) to synchronize the time with NTP server. If you choose to use another NTP server, please place a checkmark next to Provide NTP server and fill out the NTP server candidates text field. Figure 20.A - System: System Properties Figure 20.B - System: Time Sychronization 18 19 5.2 System - Administration Gateway login password and SSH accessibility can be configured in this page. Figure 21.A - Administration: Router Password Figure 21.B - Administration: SSH Access 5.3 System - Backup Click GENERATE ARCHIVE button to download the configuration file with the current gateway settings. Figure 22.A - Backup/Restore 20 Click PERFORM RESET button to reset the firmware to its initial state. Please note that the LoRa provision settings will NOT be reset by this action. Figure 22.B - Backup/Restore Choose the most recent backup file and click UPLOAD ARCHIVE to restore the configuration file. (figure 22.C & figure 22.D) Figure 22.C - Backup/Restore 21 Figure 22.D - Backup/Restore 5.4 System - System Firmware Click CHECK NEW FIRMWARE button to search the OTA server for the latest version of the new system firmware. Once a new system firmware version is detected on the OTA server, click UPGRADE NOW button to upgrade the newest system firmware from OTA server. Figure 23.A - System Firmware Figure 23.B - System Firmware 22 5.5 System - Reboot Click PERFORM REBOOT to reboot your gateway. Figure 24 - System Firmware 23 Network 6 The System menu consists of the following categories: WAN, Wireless, LAN, DHCP, Static Routes and Diagnostics. Introduction and input procedures for each category are described in the following paragraphs. 6.1 Network - WAN The purpose of this category is to view current WAN settings. This category is further divided into three sectors: Ethernet Wan, 3G/4G LTE and Wireless Extender. These individual options are lodged and labeled above the main content panel. Figure 25 - WAN 6.1.1 Ethernet WAN Figure 26.A - WAN: Static IP This page is to setup the connection type in terms of Static IP, DHCP client or PPPoE. The three different options can be selected in the drop-down menu in wantype. Please fill in the respective fields exhibited under each selection. Please make sure the Ethernet cable is connected to a WAN port. 24 25 Figure 26.B - WAN: DHCP Client Figure 26.C - WAN: PPPoE 6.1.2 3G/4G LTE This page is to setup required information. Make sure the SIM card is installed. Figure 27 - WAN: 3G/4G LTE 26 6.1.3 Wireless Extender This page is to setup the Wireless Extender Mode for WAN connection. To activate the extended wireless connection, please select Enable from the Extender mode drop-down menu (figure 24.A). Click the SCAN button to obtain the list of available Access Points within your surrounding vicinity

(figure 24.B). Figure 28.A - WAN: Wireless Extender 6.2 Network - Wireless The Wireless Setting is divided into two sectors in the same page: 2.4G and 5G. 6.2.1 2.4G 2.4G Interface Configuration to setup 2.4G wireless. SSID, encryption type, and channels can be lodged within this sector. 27 Figure 29.A - Wireless Setting: 2.4G 6.3 Network - LAN LAN IP can be setup in this page. Figure 30 - LAN 6.4 Network - DHCP You can manage detailed DHCP server settings, which includes First leased address, the allowed Number of leased addresses and Lease time. Information on Active Leases can be viewed at the bottom of this page. Figure 31 - DHCP 28 6.5 Network - Static Routes Static routes can be established by clicking the ADD button to enter proper settings. Click Delete to erase the entry. Always click the SAVE button to apply your settings. Figure 32 - Static Routes 6.6 Network - Diagnostic Diagnostics is divided into three parts on the same page: PING, TRACEROUTE and NSLOOKUP. Please see the following for input guidelines. 6.6.1 PING Input a specific IP address in the text field above PING. 29 Click the PING button to ping the IP you have specified. Figure 33.A - Diagnostics 6.6.2 TRACEROUTE Input a specific URL or IP address above TRACEROUTE. Click the TRACEROUTE button to trace the URL or IP address you have specified. Figure 33.B - Diagnostics Figure 33.C - Diagnostics 6.6.3 NSLOOKUP Input a specific URL or IP address above NSLOOKUP. Click the NSLOOKUP button to view the DNS server of the URL or IP address you have specified. 30 31 Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

-

-

- Connect the equipment into an outlet on a circuit different from that to Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.

-

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. IMPORTANT NOTE:

Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Country Code selection feature to be disabled for products marketed to the US/CANADA Operation of this device is restricted to indoor use only. 32 Professional installation instruction Please be advised that due to the unique function supplied by this product, the device is intended for use with our interactive entertainment software and licensed third-party only. The product will be distributed through controlled distribution channel and installed by trained professional and will not be sold directly to the general public through retail store. 1. Installation personal This product is designed for specific application and needs to be installed by a qualified personal who has RF and related rule knowledge. The general user shall not attempt to install or change the setting. 2. Installation location The product shall be installed at a location where the radiating antenna can be kept 20cm from nearby person in normal operation condition to meet regulatory RF exposure requirement. 3. External antenna Use only the antennas which have been approved by Gemtek Technology Co., Ltd.. The non-approved antenna(s) may produce unwanted spurious or excessive RF transmitting power which may lead to the violation of FCC limit and is prohibited. 4. Installation procedure Please refer to users manual for the detail. 5. Warning Please carefully select the installation position and make sure that the final output power does not exceed the limit set force in relevant rules. The violation of the rule could lead to serious federal penalty. 33

Gemiek Wireless Broadband Anywhere Web Site: www.gemtek.com.tw E-Mail: adam@gemteks.com No.15-1 Zhonghua Road, Hsinchu Industrial Park Hukou, Hsinchu, Taiwan 303 Phone: +886-3-598-5535 FAX: +886-3-598-5585 Class Il Permissive Change Request Letter Date: 2022/6/16 FEDERAL COMMUNICATIONS COMMISSION Authorization and Evaluation Division 7435 Oakland Mills Rd Columbia MD 21046-1609 USA. To whom it may concern, We, Gemtek Technology Co., Ltd. would like to confirm that the product with FCC ID: MXF-WLRGFM100 (Grant date:2017/06/07) has further modification made on the on as blow lists, neither circuit design nor main function has been changed. Class Il Change reason:

Original Change (C2PC) Location of R116A, R105, Downward 2~3 mm Original design R103, R116 Direction of R116A is rotated 900 Both connector of RF one connector is MMCX RF cable cable: MMCX other side connector is Ipex Length: 120mm Length: 95mm LED 1 / 3: Horizontal Pin Direction of LED1,2,3,4 LED 2 / 4: Vertical Same Pad size for Antenna card _|Original design Modified to bigger size Adam Wang/ Manager Engineering Dept. Gemtek Technology Co., Ltd. Tel: 886 3-598-5535*1411 Fax: 886 3-597-6663 E-mail: adam@gemteks.com sry. | ol be

Gemiek No.15-1 Zhonghua Road, Hsinchu Industrial Park Wireless Broadband Anywhere Hukou, Hsinchu, Taiwan 303 Web Site: www.gemtek.com.tw Phone: +886-3-598-5535 E-Mail: adam@gemteks.com FAX: +886-3-598-5585 Confidentiality Request Letter Date: 2022/6/16 Federal Communications Commission Authorization and Evaluation Division FCC ID : MXF-WLRGFM100 Permanent Confidentiality Request Pursuant to Sections 0.457 and 0.459 of the Commission's Rules, the Applicant Hereby requests confidential treatment of information accompanying this Application As outlined below:

1. Block Diagram 2, Circuit Diagram The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457, disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this application Sincerely, falas Adam Wang/ Manager Engineering Dept. Gemtek Technology Co., Ltd. Tel: 886 3-598-5535*1411 E-mail: adam@gemteks.com

Gemiek No.15+-1 Zhonghua Road, Hsinchu Industrial Park Wireless Broadband Anywhere Hukou, Hsinchu, Taiwan 303 Web Site: www.gemfek.com.tw Phone: +886-3-598-5535 E-Mail: adam@gemteks.com FAX: +886-3-598-5585 Date: 2022/6/16 Federal Communications Commission 7435 Oakland Mills Rd Columbia MD 21046-1609 Subject: Product Certification Representative Authorization Letter FCC ID: MXF-WLRGFM100 Product name: IOT Femto Gateway To whom it may concern:

We the undersigned, hereby authorize following person to act as our agent in the preparation of an application for equipment authorization of model WLRGFM-100 to the FCC Rules and Regulations. International Certification Corp. No.3-1, Lane 6, Wen San 3rd St. Kwei Shan Dist., TaoYuan City 333, Taiwan (R.O.C.) Name : Gary Chang Job Title : Manager e-mail : garychang@icertifi.com.tw Address :

We further certifies that neither the applicant nor any party to this application, as defined in 47 CFR Ch. 1.2002(b), is subject to a denial to Federal benefits, that include FCC benefits, pursuant to section 5301 of the Anti-Drug Abuse Act of 1998, 21 U.S.C. 862. This appointment also includes the authority to complete FCC Form 731 on our behalf and sign the application as an authorized agent. Sincerely, Adam Wang/ Manager Engineering Dept. Gemtek Technology Co., Ltd. Tel: 886 3-598-5535*1411 E-mail: adam@gemteks.com.tw

WARNING:pdfminer.pdfpage:The PDF <_io.BufferedReader name='/Volumes/Scratch/Incoming/eg-scratch/3412807.pdf'> contains a metadata field indicating that it should not allow text extraction. Ignoring this field and proceeding. Use the check_extractable if you want to raise an error in this case