WIReleSS TV CONNeCT Before You Begin QuICk SeTuP With HP Wireless TV Connect, you can wirelessly stream high-definition multimedia content from your computer to your home entertainment center. Before setup, note the following configuration requirements:
Your computer must have an available HDMI port and an available USB port. Your TV (or other external display) must have an available HDMI port. NOTE: If the HDMI port on your TV is occupied with another device, consider using an HDMI switch purchased separately from an electronics retailer. For optimal performance, locate the TV adapter no further than 5 m (16.4 ft) from the PC adapter. 1 Connect the USB power cable to the PC adapter, and then connect the PC adapter and the USB power cable to the computer. NOTE: The location of the computer ports may vary. 2 Connect the TV adapter to your TV or other external display and to external power. 3 If you connected to a TV, press the input source button on the TV to select the HDMI input. When the components are connected correctly and the correct source is selected, the image on the computer display will be shown on the TV. NOTE: Make sure that your computer and TV are both powered on. NOTE: If the PC adapter light does not turn on after inserting the adapter into the HDMI port on the computer, pull it out and reinsert it. NOTE: If you are using an external display other than a TV, the display may not have an input source input button and the source may cycle automatically. NOTE: It may take a few seconds for the adapters to link to each other and for the image on the computer to display on the TV (or other external display). Components PC Adapter TV Adapter Issue Resolution Federal Communications Commission notice Canada notices Troubleshooting Regulatory and Safety Notices PC adapter to your computer. 1 HDMI connector: Connects the 2 Link light On: The adapter is linked to the TV adapter. Blinking: The adapter is attempting to link to the TV adapter. 3 USB connector: Connects the USB power cable to the PC adapter. 4 Reset button*
*The reset button on the PC adapter is used only during a software upgrade, along with the Micro USB power port on the TV adapter. NOTE: You may need to upgrade the software on your adapter to ensure compatibility with devices produced by other manufacturers. When its available, you can download updated software with installation instructions from http://www.hp.com/support. 1 Up button: Scrolls up through menu. 2 Down button: Scrolls down through menu. 3 Menu/Select button: Displays the Setup menu* and selects items. 4 HDMI port: Connects the TV adapter 5 Micro USB power port: Connects the TV adapter to external power, and can also be used to upgrade the HP Wireless TV Connect firmware. 6 Link light to your TV or display. Blinking blue: The TV adapter is attempting to link to the PC adapter. Solid white: The TV adapter is linked to the PC adapter. 7 Power light On: The adapter is on. Off: The adapter is off.
*The Setup menu allows you to add or remove a video source, modify a video source name, disconnect a wireless link, and exit the menu. To add or remove a video source, or disconnect a wireless link:
1. Press the Menu button twice. 2. Press the Down or Up button to highlight Add or Remove Video Source or Disconnect Wireless Link. 3. Press the Menu button to select the item and execute the process. 4. Press the Menu button again to confirm adding or removing a video source, or disconnecting a wireless link. 1 Power adapter and cable:
Connects the TV adapter to external power. 2 HDMI cable: Connects the TV adapter to your TV or other external display 3 USB cable: Connects the PC adapter to your computer. NOTE: To add a new video source after removing one, repeat the above process. To modify the video source name:
1. Press the Menu button twice. 2. Press the Down button to highlight Modify Video Source name. 3. Press the Menu button to execute the naming process. 4. Press the Menu button to select the video source to be renamed. 5. Use the Up or Down buttons to move horizontally and highlight the character to be changed. 6. Press the Menu button to select the character to be changed. 7. Press the Up or Down buttons to change the character. 8. Press the Menu button to select the new character. 9. Press and hold the Menu button to select Save or Exit Video Source name. After the Save or Exit function has been selected, the display returns to the main menu. NOTE: You may need to upgrade the software on your adapter to ensure compatibility with devices produced by other manufacturers. When its available, you can download updated software with installation instructions from http://www.hp.com/support. Cables 1 2 3 663694-001 Barbossa_v32.indd 1 Product: Wireless HDMI Document: Consumer QSP Color page 1: CMYK + PMS 640 Color page 2: CMYK + PMS 640 Part number: 621361-001 Flat size: 27.5 x 17 Finished size: 5.5 x 8.5 Fold 1: Horizontal, in half Fold 2: 5-panel accordion The power light on the TV adapter does not turn on. Ensure that the power adapter is securely connected to the TV adapter and to a wall outlet. Plug another device into the wall outlet to ensure that the outlet is functioning. The link light on the TV adapter does not turn on. Ensure that the HDMI cables are securely connected to the components. The link light turns on but continues to blink. The TV does not display the image that is on the computer. Nothing happens when I press the Reset button on the PC adapter. Wait a few minutes for the components to complete initialization. You should see messages on the computer and/or TV screen. It may take up to 5 minutes for initialization to complete. Ensure that you have connected the components according to the instructions. Press the input source button on the TV to select the HDMI input. The Reset button on the PC adapter is only used for software upgrades. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment to an outlet on a circuit different from that to which the Consult the dealer or an experienced radio or television technician for help. receiver is connected. Modifications The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly approved by HP may void the users authority to operate the equipment. Cables To maintain compliance with FCC Rules and Regulations, connections to this device must be made with shielded cables having metallic RFI/EMI connector hoods. Declaration of Conformity for products marked with the FCC logo
(United States only) This device complies with Part 15 of the FCC Rules. Operation is subject to the following 2 conditions:
1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. If you have questions about the product that are not related to this declaration, write to:
Hewlett-Packard Company P. O. Box 692000, Mail Stop 530113 Houston, TX 77269-2000 For questions regarding this FCC declaration, write to:
Hewlett-Packard Company P. O. Box 692000, Mail Stop 510101 Houston, TX 77269-2000 or call HP at 281-514-3333 To identify your product, refer to the part, series, or model number located on the product. This device must not be co-located or operating in conjunction with any other antenna or transmitter. WARNING! Exposure to Radio Frequency Radiation The radiated output power of this device is below the FCC radio frequency exposure limits. Nevertheless, the device should be used in such a manner that the potential for human contact is minimized during normal operation of tablet PCs and notebook computers. To avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antennas should not be less than 20 cm (8 inches), including when the computer display is closed. CAUTION: When using IEEE 802.11a wireless LAN, this product is restricted to indoor use, due to its operation in the 5.15- to 5.25-GHz frequency range. The FCC requires this product to be used indoors for the frequency range of 5.15 GHz to 5.25 GHz to reduce the potential for harmful interference to cochannel mobile satellite systems. High-power radar is allocated as the primary user of the 5.25- to 5.35-GHz and 5.65- to 5.85- GHz bands. These radar stations can cause interference with and/or damage to this device. In some environments, the use of wireless devices may be restricted. Such restrictions may apply in hospitals, near explosives, in hazardous locations, and so on. If you are uncertain of the policy that applies to the use of this product, ask for authorization to use it before you turn it on. This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. The device complies with Industry Canada license-exempt RSS standard(s). Wireless operation is subject to 2 conditions. The first is that the wireless device may not cause interference. The second is that the wireless device must accept any interference, including interference that may cause undesired operation of the device. CAUTION: When using IEEE 802.11a wireless LAN, this product is restricted to indoor use, due to its operation in the 5.15 to 5.25 GHz frequency range. Industry Canada requires this product to be used indoors for the frequency range of 5.15 GHz to 5.25 GHz to reduce the potential for harmful interference to co-channel mobile satellite systems. High-power radar is allocated as the primary user of the 5.25 to 5.35 GHz and 5.65 to 5.85 GHz bands. These radar stations can cause interference with and/or damage to this device. The antennas for this device are not replaceable. Any attempt at user access will damage your computer. AC adapter notices WARNING! To reduce the risk of electric shock or damage to the equipment:
Plug the AC adapter into an AC outlet that is easily accessible Disconnect power from the product by unplugging the AC adapter from the AC outlet (not by unplugging the AC adapter from the product). WARNING! To reduce potential safety issues, only the AC adapter provided with the product, a replacement AC adapter provided by HP, or an AC adapter purchased as an accessory from HP should be used with the product. Wireless Antennas The wireless antennas transmit signals from the PC adapter to the TV adapter. These antennas are not visible from the outside of the adapters. NOTE: For optimal transmission, keep the areas immediately around the antennas free from obstructions. Copyright 2011 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical and editorial errors or omissions contained herein. First Edition: September 2011 663694-001 Replace this box with PI statement as per spec. Replace this box with PI statement as per spec. Replace this box with PI statement as per spec. Replace this box with PI statement as per spec. Replace this box with PI statement as per spec. 9/1/2011 4:34:08 PM 6620 Cypresswood DriveSuite 120Spring, TX 77379832.717.4331English on front (outside)English on front (outside) CONNeCTeuR TV SANS Avant de commencer INSTAllATION RAPIde Avec le connecteur TV sans fil HP, transmettez sans fil en continu du contenu multimdia haute dfinition de votre ordinateur votre centre de divertissement personnel. Avant linstallation, consultez les exigences de configuration suivantes :
Votre ordinateur doit avoir un port HDMI et un port USB disponibles. Votre tlviseur (ou un autre cran externe) doit avoir un port HDMI disponible. REMARQUE : Si le port HDMI de votre tlviseur est dj utilis par un autre priphrique, pensez utiliser un commutateur HDMI achet sparment chez un vendeur de produits lectroniques. Pour une performance optimale, ne placez pas ladaptateur TV plus de 5 m (16.4 pd) de ladaptateur PC. 1 Connectez le cble dalimentation USB ladaptateur PC, puis connectez ladaptateur PC et le cble dalimentation USB lordinateur. REMARQUE : Lemplacement des ports de lordinateur peut varier. 2 Connectez ladaptateur TV votre TV ou un autre cran externe et lalimentation externe. 3 Si vous tes connect un tlviseur, appuyez sur le bouton de la source dentre sur le tlviseur pour slectionner lentre HDMI. Lorsque les composants sont correctement connects et que la source est bien slectionne, limage sur lcran de lordinateur sera affiche sur le tlviseur. REMARQUE : Si le voyant de ladaptateur PC ne sallume pas aprs avoir insr ladaptateur dans le port HDMI sur lordinateur, sortez-le et rinsrez-le. REMARQUE : Assurez-vous que votre ordinateur et le tlviseur sont tous les deux sous tension. REMARQUE : Si vous utilisez un cran externe autre quun tlviseur, lcran peut ne pas avoir un bouton de source dentre, mais la source peut changer automatiquement. REMARQUE : Cela peut prendre quelques secondes pour que les adaptateurs se connectent les uns aux autres et pour que limage de lordinateur saffiche sur le tlviseur (ou un autre cran externe). Composants Adaptateur PC Adaptateur TV 1 Bouton Haut : Permet de faire dfiler le menu vers le haut. 2 Bouton Bas : Permet de faire dfiler le menu vers le bas. 3 Bouton Menu/Slection : Affiche le menu de configuration* et permet de slectionner des lments. 4 Port HDMI : Connecte ladaptateur TV votre affichage ou tlviseur. 5 Micro-port dalimentation USB : Connecte ladaptateur TV une alimentation externe, et peut galement tre utilis pour mettre niveau le microprogramme HP Wireless TV Connect. 6 Voyant de liaison Bleu clignotant : Ladaptateur TV tente de se connecter ladaptateur PC. Blanc fixe : Ladaptateur TV est connect ladaptateur PC. 7 Voyant dalimentation Allum : Ladaptateur est allum. teint : Ladaptateur est teint.
*Le menu de configuration permet dajouter ou de supprimer une source vido, de modifier un nom de source vido, de dconnecter une liaison sans fil, et de quitter le menu. Pour ajouter ou supprimer une source vido, ou pour dconnecter une liaison sans fil :
1. Appuyez deux fois sur le bouton Menu :
2. Appuyez sur le bouton Bas ou Haut pour mettre en vidence Ajouter ou supprimer source vido ou Dconnecter liaison sans fil 3. Appuyez sur le bouton Menu pour slectionner llment et excuter le processus. 4. Appuyez nouveau sur le bouton Menu pour confirmer lajout ou la suppression dune source vido, ou la dconnexion dune liaison sans fil. REMARQUE : Pour ajouter une nouvelle source vido aprs en avoir supprim une, rptez le processus ci-dessus. Pour modifier le nom de la source vido :
1. Appuyez deux fois sur le bouton Menu. 2. Appuyez sur le bouton Bas pour mettre en surbrillance Modifier nom de source vido. 3. Appuyez sur le bouton Menu pour excuter le processus de nommage. 4. Appuyez sur le bouton Menu pour slectionner la source vido renommer. 5. Utilisez le bouton Haut ou Bas pour vous dplacer horizontalement et mettre en surbrillance le caractre modifier. 6. Appuyez sur le bouton Menu pour slectionner le caractre modifier. 7. Appuyez sur le bouton Haut ou Bas pour modifier le caractre. 8. Appuyez sur le bouton Menu pour slectionner le nouveau caractre. 9. Appuyez sur le bouton Menu et maintenez-le enfonc pour slectionner Enregistrer ou Quitter nom de source vido. ladaptateur PC votre 1 Connecteur HDMI : Connecte ordinateur. 2 Voyant de liaison Allum : Ladaptateur est connect ladaptateur TV. Clignotant : Ladaptateur tente de se connecter ladaptateur TV. 3 Connecteur USB : Connectez le cble dalimentation USB ladaptateur PC. 4 Bouton Rinitialiser*
*Le bouton de rinitialisation sur ladaptateur PC est utilis uniquement lors dune mise niveau logicielle, ainsi que le micro-port dalimentation USB sur ladaptateur TV. REMARQUE : Vous pouvez tre amen mettre jour le logiciel sur votre adaptateur pour assurer la compatibilit avec les priphriques produits par dautres fabricants. En cas de disponibilit, vous pouvez tlcharger le logiciel mis jour, accompagn des instructions dinstallation, partir de ladresse http://www.hp.com/support. Cbles 1 2 3 1 Adaptateur et cble dalimentation : Connecte ladaptateur TV une alimentation externe. 2 Cble HDMI : Connecte ladaptateur TV votre tlviseur ou un autre cran externe. 3 Cble USB : Connecte ladaptateur PC votre ordinateur. 663694-001 Barbossa_v32.indd 2 Product: Wireless HDMI Document: Consumer QSP Color page 1: CMYK + PMS 640 Color page 2: CMYK + PMS 640 Part number: 621361-001 Flat size: 27.5 x 17 Finished size: 5.5 x 8.5 Fold 1: Horizontal, in half Fold 2: 5-panel accordion Rsolution des problmes Problme Rsolution Le voyant d'alimentation sur l'adaptateur TV ne s'allume pas. Assurez-vous que l'adaptateur d'alimentation est correctement connect l'adaptateur TV et une prise murale. Branchez un autre priphrique sur la prise murale pour vous assurer qu'elle fonctionne. Assurez-vous que les cbles HDMI sont correctement connects aux composants. Patientez quelques minutes pour que les composants terminent l'initialisation. Vous devriez voir des messages sur l'cran de l'ordinateur et/ou du tlviseur. Cela peut prendre jusqu' 5 minutes pour que l'initialisation se termine. Assurez-vous que vous avez connect les composants conformment aux instructions. Appuyez sur le bouton de la source d'entre sur le tlviseur pour slectionner l'entre HDMI. Le bouton Rinitialiser de l'adaptateur PC est utilis uniquement pour les mises jour logicielles. Le voyant de liaison sur l'adaptateur TV ne s'allume pas. Le voyant de liaison s'allume mais continue de clignoter. Le tlviseur n'affiche pas l'image qui est sur l'ordinateur. Rien ne se passe lorsque j'appuie sur le bouton Rinitialiser sur l'adaptateur PC. Informations sur la scurit et les rglementations Informations pour le Canada Cet appareil numrique de classe B est conforme aux exigences des rgulations canadiennes sur les quipements causant des interfrences. Lappareil est conforme aux normes RSS sans licence dIndustry Canada. Lutilisation sans fil est sujette deux conditions. La premire est que le priphrique sans fil ne doit pas causer dinterfrences. La seconde est que le priphrique sans fil doit accepter toutes les interfrences, y compris les interfrences qui peuvent causer un dysfonctionnement du priphrique. ATTENTION : Si vous utilisez un rseau local sans fil IEEE 802.11a, lutilisation de ce produit est limite une utilisation en intrieur, cause de son fonctionnement dans une gamme de frquence de 5.15 5.25 GHz. Industry Canada exige que ce produit soit utilis lintrieur pour la gamme de frquence de 5.15 5.25 GHz afin de rduire le risque dinterfrences nuisibles avec les systmes co-canal mobiles par satellite. Les radars puissance leve sont les utilisateurs principaux des bandes de 5.25 5.35 GHz et de 5.65 5.85 GHz. Ces stations de radar peuvent causer des interfrences avec ce priphrique et/ou lendommager. Les antennes de ce priphrique ne sont pas remplaables. Toute tentative daccs utilisateur endommagera votre ordinateur. Avis Canadien Cet appareil numrique de la classe B respecte toutes les exigences du Rglement sur le materiel brouilleur du Canada. Informations sur ladaptateur secteur Informations sur ladaptateur secteur Antennes sans fil Les antennes sans fil transmettent des signaux de ladaptateur PC ladaptateur TV. Ces antennes ne sont pas visibles de lextrieur des adaptateurs. REMARQUE : Pour optimiser les transmission, vitez dobstruer les zones situes immdiatement autour de lantenne. AVERTISSEMENT ! Pour rduire les risques dlectrocution ou de dtrioration du matriel :
Branchez ladaptateur secteur sur une prise secteur facile daccs. Coupez lalimentation du produit en dbranchant ladaptateur secteur de la prise secteur
(plutt que du produit). AVERTISSEMENT ! Pour limiter les risques lis la scurit, nutilisez que ladaptateur secteur fourni avec le produit, un adaptateur secteur de rechange fourni par HP ou un adaptateur secteur achet comme accessoire auprs de HP. Une fois la fonction Enregistrer ou Quitter slectionne, laffichage revient au menu principal. REMARQUE : Vous pouvez tre amen mettre jour le logiciel sur votre adaptateur pour assurer la compatibilit avec les priphriques produits par dautres fabricants. En cas de disponibilit, vous pouvez tlcharger le logiciel mis jour, accompagn des instructions dinstallation, partir de ladresse http://www.hp.com/support. 9/1/2011 4:34:19 PM 6620 Cypresswood DriveSuite 120Spring, TX 77379832.717.4331English on front (outside)English on front (outside)