User's Manual Smart WiFi Plug Model : WSPUS 01 TABLE OF CONTENTS 3 1. Profile ---------------------------------------------------------
4 2. Safety Precautions -----------------------------------------
3. General Specications ------------------------------------
5 4. Introduction --------------------------------------------------- 5 5. Install Guide -------------------------------------------------- 7 6. Configurations steps ---------------------------------------
7 7. Reset or delete the APP of WiFi plug ------------------ 14 8. Timer ----------------------------------------------------------- 15 9. Descriptions of access control --------------------------- 15 10. Setup a scene ---------------------------------------------- 15 11. Electricity statistics ---------------------------------------- 16 12. FAQ ----------------------------------------------------------- 17 Warranty card ----------------------------------------------- 18 Packing List :
Smart WiFi Plug ---------------------------------------------- 1pcs User Manual --------------------------------------------------- 1pcs 1. Profile The smart WiFi plug is controlled via an APP installed in an Android or iOS smart phones or tablets, user can local or remote turn ON/OFF the device with WiFi signal and telecom mobile network signal provided and internet access be available. Usersapparatus can be powered through this plug, so that it can be controlled and monitored with the APP installed. This plug will be a good choice for family, companies, offices, factories, shopping malls, stores, etc to realize local or remote power control or timing or power saving requirements with multi-timer, power consumption measurement, multi-user control, etc functions provided in the APP. 1.1 The smart WiFi plug can be used as Smart home control Offices, Factories, Residential intelligent control 1.2 Wiring diagram 1.3 Diagram of how the plug is connected 1.4 Features 2. Safety Precautions To avoid any risk of unexpected harm or injury or damage to the smart WiFi plug, please read the manual thoroughly before operation and keep it carefully for future reference. Users should always comply with the safety precautions. This device is powered up and operated with voltage in 250Va.c., Higher supplied voltage might damage the internal components, and it may be abnormal with lower voltage supplied. Make sure the device be plugged into a proper socket and accommodates proper WiFi plug. To avoid the risk of electric shock, keep the operating power plug away from a place that children or pets are easy to access. Depends on the APP setting, the device may automatically power up the connected external apparatus, please make sure there isn't any direct or indirect harm or damage will occur once the apparatus being powered. This device is designed for indoor use only, it shall not be squeezed or impacted violently. It should be situated away from those devices or environment with excessive hot, cold, humid, wet, strong magnetic, strong electromagnetic interference (EMI), strong ultra-violet radiation, high static, high voltage or flammable, explosive materials. It is recommended unplug the device during lightning storms days. Don't spill liquid on the power plug. For cleaning, please use soft cloth without any type of solvent or aerosol. Users are not permitted to make any change or modification to the device in any way. High-voltage circuitry applied inside the device, strictly forbid non-professionals disassembling or taking the device apart, otherwise, high risk of electric shock may occur. If you have any questions or problems concerning the smart WiFi plug
, please consult the experienced technician or your local dealer. 3. General Specifications Wireless Standard Operation Frequency
: IEEE802.11b/g/n
: ISM band 2412~2462MHz
(Depends on country region)
: Mac Encryption; WEP,WAPI
,TKIP and AES Security Operating current& Voltage : 90 -264V~ (60-50Hz)
: Max.10A/ 2000W) Socket Output Load WIFI Socket Output Load
: Max.10A/ 2000W)
: 5000 Plug mating cycles
: 100mm x 62mmx 38mm Dimension Net Weight
: 150gs 4. Introduction 4.1 Function descriptions No. Function Details WiFi indicator When output power turn on, LED turn on, output power turn off, LED turn off also. Manual control Button 1.In need to manually power control, once press the button to turn on, twice press to off. 2.To reset factory default, press the button about 5 seconds till LED flash rapidly. 3.When output power turn on, LED turn on, output power turn off, LED turn off also. 4.To AP mode, press the button about 10 seconds till LED flash quickly become slow flash. It let the APP directly connect to the plug without other WiFi signal or telecom signal needed. Socket output Standard US output Socket. 6 Plug input Standard US input plug. 1 2 3 4 5. Install Guide The following hardware devices are necessary before configuration 5.1 Properly functional WiFi router. 5.2 APP devices like mobile phone, tablet etc(Android and IOS). 6. Configurations steps 6.1Firstly, download the APP onto your APP devices like mobile phone or tablet, Scanning the following QR code, and download it directly. Click the icon to enter Wifi Plug 6.1.1 Update APP To improve the consumer's demand and make the interfaces friendlier, the APP may be updated occasionally. To know if there's any update, please find APP. It is shown as the following figure. and click to update the 6.1.2 Some QR code APP might not be able to recognize the above of QR code. Please change another APP any try again. 6.2 Check whether mobile phone or tablet is connected to a WiFi router properly as shown in the following figure. Please noted the interface and function of mobile phone or tablet may be different. 6.3 This product has two kinds of connection modes, it is described respectively as follows:
6.3.1 Indirect or Client mode: A mobile phone or tablet PC is connected to a router then to the WiFi plug . 6.3.2 Direct or AP mode: The plug is set to hotspot (AP) mode first, a mobile phone or tablet PC is directly connected to AP of the plug, therefore, remote control the WiFi plug as follows:
6.4 Client mode: Please reset the WiFi plug to factory defaults at the first time using or the WiFi network is changed. 6.4.1 Reset to factory defaults: Insert the WiFi plug into a proper power outlet, when the blue indicator fiash normally, press the button on WiFi plug for about 5 seconds till the blue indicator blink rapidly, release the button to finish client mode configuration, all these reset the WiFi plug to its factory default settings. Note: the button press period should not be too long (more than 10 seconds), otherwise it set the WiFi plug into the AP mode (LED flashes quickly to slowly). 6.5 Using the mobile phone or tablet to find APP and tap to run it, then find configuration the current connected WiFi network, input the SSID and password, click on "start configuration"
icon of WeConn click to enter 6.5.1 Depending on the status of the current WiFi network, the whole configuration process takes about 3 ~ 30 seconds. If the connection is successful, the APP interface displays" A new device is added" or
"Some devices are online, no newly-added device founded". 6.5.2 New device is added : means new equipment is successfully added. 6.5.3"Some devices are online, no newly-added device founded"
may imply two means. 6.5.3.1 Configuration failure. 6.5.3.2 Configuration has been successfully done before, check the device list to see if is shown as "Local", if not, means configuration failure, configurate it again. 6.5 .4 FAQ of configuration failure:
6.5.4.1 Too many devices are being connected to the specific router. 6.5.4.2 Router has been set to filtering mode (such as MAC address filtering), allowing only authorized access equipment. 6.5.4.3 Password was wrong. 6.5.4.4 Wireless WiFi signal is too weak , too far away from the specific router. 6.5.4.5 The router is abnormal for some reason. 6.5.4.6 There are some have strong electromagnetic interference nearby. 6.5.4.7 Several devices may try to connect the router at the same time. Unplug the WiFi plug for about 10 seconds, then plug it into a socket to power up again, if it is still abnormal, rest it to Factory Settings. 6.5.5 After a device is successfully added, goes back configuration page, find the WFiPlug icon and click into a list, click to choose a device, enter into a page 6. 5. 5. 1It depends on the network condition, WiFi plug device list may display three connection statuses: local, Internet, off- line. Local: the current mobile phone or tablet and WiFi plug are being connected to a local router, the following figure shows the topology Internet : the current mobile phone or tablet and WiFi plug are connected via some extra internet network loops rather within a router coverage, the following figure shows the topology. Off-line : it means the current mobile phone or tablet and WiFi plug are unsuccessfully connected, the plug can be controlled. 6.5.5.2 The control interface Lock : Only administrator is permitted to control;
Unlock : Related members are all allowed to control. Control key control the three states 6.6. Control over Internet rather than LAN mode. 6.6.1 Connect the mobile phone or tablet to power plug via different WiFi or cell phone network, exit the Settings menu. 6.6.2 Enter into "Equipment list" as shown in following figure. Depends WiFi signal or network condition , it may take about 5 seconds to 3 minutes to have "internet" shown up. 6.7 Direct connection (Hotspot/AP) mode: Should the blue LED of WiFi plug flashes normally, press down the button for about 10 seconds rather than 5 seconds, LED flashes from blue quickly flashes in red slow flash in red, then release button to enter into AP mode. 6.8 Change WiFi connection setting of the mobile phone or tablet, Connect it to WiFi plug network (Hotspot) with a name as Weconn****, exit setting page after successful connection, further operation can be proceeded. Note: It is strange to show about 1 minute delay for IOS system to have a tickle mark to indicate a successful WiFi connection, well, evens so, you be able to enter the APP and proceed normal operation before that time. 6.8.1 Internet control can't be proceeded at direct connection
(Hotspot/AP) mode connection, and the WiFI connection distance is limited. 6.8.2 Quit the plug from direct connection (AP) mode to indirection
(client) mode: Reset the plug to factory setting and reconnect as aforesaid configuration mentioned. 7. Reset or delete the APP of WiFi plug 8.Timer 9. Descriptions of access control 10. Setup a scene 11. Electricity statistics 12. FAQ 12.1. WiFi control app going crashed?
Answer : A. Please cancel the WiFi plug power supply for about 10 seconds, and then re energized B. Reset the WiFi plug system please shorten distance between them water heater, TV andelectric cooker etc, make them smart controllable products on your phone 12.2. Cannot log in the app?
Answer : Check whether your APP meets Android and IOS operating 12.3. Smart terminal with app cannot connect to WiFi ?
Answer : Check if app and WiFi connect well or not 12.4. WiFi control Led indicator is not working Answer : Check if input power in the range of 90-264Va.c. 12.5. App operation unstable?
Answer : Maybe the problem is WiFi plug if too far from the WiFi, 12.6. More application scenes Answer : This WiFi plug can be connected to curtain, lights, door, 12.7. What does the plug can do?
Answer : It can be used to control electricity to curtain, lamp, 12.8. What is the max load connected?
Answer : Max. 2000W load can be connected to the plug , otherwise, 12.9. Is there any cost to use the server?
Answer : It can be used freely for 3 years since the plug is activated, electricity to the load will be cut off automatically door gate, water heater etc it maybe charged after that General Jack Technology Co.,Ltd THE AREA OF ADMINISTRATION OF LANGBEI. CHANG PING,DONGGUAN,GUANGDONG,CHINA HOME PAGE:http://www.g-jack.com FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the followingmeasures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which thereceiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.