FCC ID: NZLSAHL5M Wireless Garage Door Opener

Programming and Information Guide



Programming 2-Button HomeLink:

Before programming HomeLink During programming, it is possible that garage doors, gates, or other devices may operate. For this reason, make sure that people and objects are clear of the garage door or other devices to prevent injury or other potential harm. It is recommended that a new battery be placed in the remote control transmitter for more accurate programming. Garage door opener motors manufactured after 1995 may be equipped with rolling code protection. If this is the case, you may need a stepladder or other sturdy, safe device to reach the Learn or Smart button on the garage door motor. Please note that the instructions below apply to the majority of HomeLink use cases. However, there are some HomeLink applications or HomeLink compatible systems that require slightly different instructions. Programming a brand new HomeLink HomeLink indicator light in view. Position the hand-held transmitter 1-3 inches away from the HomeLink surface, keeping the Using both hands, simultaneously press and hold both the desired HomeLink button and hand held transmitter button. DO NOT release until the HomeLink indicator light flashes slowly and then changes to solid or rapidly flashing. The change in flashing indicates the frequency signal has been learned. o Note: Some gate operators and garage door openers may require you to use the cycling procedure noted in the Programming an entry gate section. Press and hold the programmed HomeLink button and observe the indicator light. o If the indicator light is solid/continuous, programming is complete and your device should activate when the HomeLink button is pressed and released. o If the indicator light blinks rapidly, proceed with the following programming instructions for a rolling code device. o A second person may make the following steps quicker and easier. Use a stepladder or other stable, safe device. Rolling Code At the garage door opener motor in the garage, locate the learn or smart button (usually near where the hanging antenna wire is attached to the unit). If there is difficulty locating the learn or smart button, reference the garage door openers manual. Press and release the learn or smart button (the name and color of the button may vary by o Note: Once the button is pressed, there are typically about 30 seconds in which to initiate manufacturer). the next step. Return to the vehicle and press and release the programmed HomeLink button. Repeat the press/release sequence up to 3 times to complete the training process. HomeLink should now activate your rolling code equipped device. To program additional HomeLink buttons, repeat this process. Once programmed, the HomeLink Wireless Control System or the original hand-held transmitter may be used to activate the device (e.g. garage door, entry lock, gate, etc.). Programming an entry gate (for U.S.A. owners)/Programming a device in the Canadian market Position the hand-held transmitter 1-3 inches away from the HomeLink surface, keeping the HomeLink indicator light in view. Using both hands, hold the HomeLink button, and simultaneously press and release the hand-

held transmitter button at 2-second intervals. DO NOT release the HomeLink button until the indicator light flashes slowly and then changes to solid or rapidly flashing. The change in flashing indicates the frequency signal has been learned.



Programming and Information Guide Press and hold the programmed HomeLink button and observe the indicator light. o If the indicator light is solid/continuous, programming is complete and your device should activate when the HomeLink button is pressed and released. o If the indicator light blinks rapidly, proceed with the following programming instructions for a rolling code device. o A second person may make the following steps quicker and easier. Use a stepladder or other stable, safe device. Rolling Code At the garage door opener motor in the garage, locate the learn or smart button (usually near where the hanging antenna wire is attached to the unit). If there is difficulty locating the learn or smart button, reference the garage door openers manual. Press and release the learn or smart button (the name and color of the button may vary by o Note: Once the button is pressed, there are typically about 30 seconds in which to initiate manufacturer). the next step. Return to the vehicle and press and release the programmed HomeLink button. Repeat the press/release sequence up to 3 times to complete the training process. HomeLink should now activate your rolling code equipped device. To program additional HomeLink buttons, repeat this process. Once programmed, the HomeLink Wireless Control System or the original hand-held transmitter may be used to activate the device (e.g. garage door, entry lock, gate, etc.). Reprogramming a single HomeLink button When the following procedure is performed, buttons which already have devices registered to them can be overwritten:

Press and hold the desired HomeLink button. After about 20 seconds, the HomeLink indicator will start slowly flashing. While continuing to hold the HomeLink button, position the hand-held transmitter 1-3 inches away from the HomeLink and press and hold the hand held transmitter button until HomeLink indicator light changes to solid or rapid flashing. The change in flashing indicates the frequency signal has been learned so, you can release both the buttons. o Note: Some gate operators and garage door openers may require you to use the cycling procedure noted in the Programming an entry gate section. Press and hold the programmed HomeLink button and observe the indicator light. If the indicator light is solid/continuous, programming is complete and your device should activate when the HomeLink button is pressed and released. If the indicator light blinks rapidly, proceed with the instructions listed in the Rolling Code section. If you do not program a new device to the button, it will revert to the previously held programming. o o Erasing Your HomeLink memory (both buttons) Press and hold both buttons for 10 seconds until the HomeLink indicator light changes from solid to flashing indicator. If you sell your vehicle, be sure to erase the HomeLink memory. Sommer Rolling Code Programming Steps:

Note: if you are training two devices, and only one is a Sommer, you will need to train the Sommer unit first, and then follow the Reprogramming a single HomeLink button instructions for your second device. Press and hold both HomeLink buttons for 20 seconds until the LED turns off.



Programming and Information Guide door. The HomeLink is now ready to be programmed to the Sommer Rolling Code Opener garage o A second person will make the following steps quicker and easier. Use a stepladder or other stable, safe device. At the garage door opener motor in the garage, locate the learn or smart button (usually near where the hanging antenna wire is attached to the unit). If there is difficulty locating the learn or smart button, reference the garage door openers manual. Press and release the learn or smart button (the name and color of the button may vary by Note: Once the button is pressed, there are between 10 and 30 seconds in which to initiate the model). next step. Return to the vehicle and press and release the programmed HomeLink button. Repeat the press/release sequence up to 3 times to complete the training process. HomeLink should now activate your Sommer rolling code equipped device. To train additional Sommer devices to your other HomeLink button, repeat steps 4-7 of this process. To train your other HomeLink button to a non-Sommer device, follow the steps listed in Reprogramming a single HomeLink button. FCC (USA) and IC (Canada):

This device complies with FCC rules part 15 and Industry Canada RSS-210. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference that may be received including interference that may cause undesired operation. WARNING: The transmitter has been tested and complies with FCC and IC rules. Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the device. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End Users must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must be at least 20 cm from the user and must not be co-located or operating in conjunction with any other antenna or transmitter. The term IC: before the certification/registration number only signifies that Industry Canada technical specifications were met. FCC (USA) et IC (Canada):

Cet appareil est conforme aux normes FCC partie 15 des rgles et Industrie Canada RSS-210. Son fonctionnement est soumis aux deux conditions suivantes: (1) Ce dispositif ne peut causer des interfrences nuisibles, et (2) Cet appareil doit accepter toute interfrence qui peuvent tre reues, y compris les interfrences qui peuvent provoquer un fonctionnement indsirable. AVERTISSEMENT:

L'metteur a t test et est conforme aux rgles de la FCC et IC. Les changements ou modifications non expressment approuvs par la partie responsable de la conformit pourraient annuler l'autorit de l'utilisateur utiliser l'appareil. Cet quipement est conforme aux limites FCC d'exposition aux radiations dfinies pour un environnement non contrl. Les utilisateurs finaux doivent suivre les instructions de fonctionnement spcifiques pour satisfaire aux normes d'exposition aux RF. Cet metteur doit tre d'au moins 20 cm de l'utilisateur et ne doit pas tre co-situe ni fonctionner en conjonction avec une autre antenne ou metteur. Le terme "IC:" devant le numro de certification / enregistrement signifie seulement que les spcifications techniques d'Industrie Canada ont t respectes.



a 4 A full list of relevant patents is at www.gentex.com/patents FORD PART NO: FLSB-19H313-AC 7 GENTEX: 960-0360 FCC ID: NZLSAHLS5M IC: 4112A-SAHLSM MODEL: SAHLSM IFETEL: XXXXXXXXX-XXXX YYYY DD MONTH a Home Link. BY GENTEX CORPORATION TLV yyy

GENTEX A Smarter Vision Request for Confidentialit Date: 10/28/20 Subject: Confidentiality Request for: NZLSAHL5M Pursuant to FCC 47 CRF 0.457(d) and 0.459 and IC RSP-100, Section 9.4, the applicant requests that a part of the subject FCC application be held confidential. Type of Confidentiality Requested Exhibit

[-] Short Term [x] Permanent Block Diagrams

[_] Short Term External Photos

[-] Short Term L_] Permanent*' Internal Photos

[_] Short Term XX] Permanent Operation Description/Theory of Operation L] Short Term >] Permanent Parts List & Placement/BOM

[|] Short Term ><] Permanent Tune-Up Procedure

[_] Short Term >] Permanent Schematics

[_] Short Term Test Setup Photos

[_] Short Term [_] Permanent*3 User's Manual Gentex Corporation has spent substantial effort in developing this product and it is one of the first of its kind in industry. Having the subject information easily available to "competition" would negate the advantage they have achieved by developing this product. Not protecting the details of the design will result in financial hardship. Permanent Confidentiality:

The applicant requests the exhibits listed above as permanently confidential be permanently withheld from public review due to materials that contain trade secrets and proprietary information not customarily released to the public. Short-Term Confidentiality:

The applicant requests the exhibits selected above as short term confidential be withheld from public view for a period of number of days not to exceed 180)*__ days from the date of the Grant of Equipment Authorization and prior to marketing. This is to avoid premature release of sensitive information prior to marketing or release of the product to the public. Applicant is also aware that they are responsible to notify ACB in the event information regarding the product or the product is made available to the public. ACB will then release the documents listed above for public disclosure pursuant to FCC Public Notice DA 04-1705. NOTE for Industry Canada Applications:

IC currently only distinguishes Permanent Confidentiality exhibits as shown above. Short Term confidentiality is not considered applicable to IC applications. Sincerely, By: : = Brian Miller

(Signature/Title?) (Print name)

- The asterisked items (*) require further information to be provided to ACB before permanent confidentiality will be extended to these exhibits. Please refer to FCC KDB 726920 and the specific Document link for DO1 found at: https://apps. fcc. gov/oetcf/kdb/forms/FTSSearchResultPage.cfm?switch=P&id=41731 and review section II, 3) regarding specific information that must accompany these requests.

~ Please refer to http://acbcert.com/documents/misc-docs/Memo-Short-Term-Vs-Standard-Confiden! y.pdf for complete details. 3 ~ Must be signed by applicant contact given for applicant on the FCC site, or by the authorized agent if an appropriate authorized agent letter has been provided. Letters should be placed on appropriate letterhead. 600 N. Centennial St. Zeeland, MI 49464 Phone 616-772-1800 + Fax 616-772-7348 www.gentex.com

GENTEX fl Smarter Vision November 9, 2020 Federal Communication Commission Equipment Approval Services, P.O. Box 358315 Pittsburgh, PA 15251-5315 Attention: Authorization & Evaluation Division Application for Certification of Gentex Corporation Transmitter under 47 CFR 15.231. Model: SAHL5M FCC ID: NZLSAHL5M To whom it may concern, Gentex Corporation requests approval for the SAHL5M product, which is a programmable frequency garage door opener and digital device controller to be installed in the automobile visor. The Gentex model SAHLSM is part of the HomeLink V series. HomeLink V devices are capable of learning garage door opener frequencies and codes from the user's original transmitter. The device is capable of learning in the range between 286MHz and 440MHz excluding forbidden frequency regions. Gentex Corporation has invested considerable resources into developing our HomeLink products. For this reason, we respectfully request that the following items be held as confidenti e Circuit Block Diagrams e Parts List e Theory of Operation Schematics e Tune Up Procedure The Federal Communications Commission will be notified, in writing of any changes in the software/programming of this device that could affect its RF characteristics. Please do not hesitate to contact me with any questions you may have regarding this report. As always, we look forward to your timely response. Brian Miller Corporate Labs Group Leader Wireless Regulatory Gentex Corporation Sincerely, 600 N. Centennial St. Zeeland, MI 49464 PHONE: 616-772-1800 FAX: 616-772-2690 http://www.gentex.com