where you would normally be advised to turn off your vehicle engine. Areas with potentially explosive atmospheres are oftenbut not alwaysposted. Blasting Caps and Areas To avoid possible interference with blasting operations, turn off your radio when you are near electrical blasting caps, in a blasting area, or in areas posted Turn off two-way radios. Obey all signs and instructions. Control Buttons Control Buttons Two-Way Radio Users Guide FPO KEM-ML36100-15 MS350 Series The MS350R is approved for use in the US only. For More Information For further information, you may call Motorola at 1-800-638-5119, e-mail us at giantintl@callcenter.com or visit us on the Internet at www.motorola.com. Safety and General Information Important Information on Safe and Efficient Operation Read This Information Before Using Your Radio. The information provided in this document supersedes the general safety information in user guides published prior to December 1, 2002. Transmit and Receive Procedure Your two-way radio contains a transmitter and a receiver. To control your exposure and ensure compliance with the general population/
uncontrolled environment exposure limits, always adhere to the following procedure:
Transmitting 50% of the time, or less, is important because the radio generates measurable RF energy exposure only when transmitting (in terms of measuring standards compliance). Transmit no more than 50% of the time. To receive calls, release the PTT button. To transmit (talk), press the Push to Talk (PTT) button. Exposure to Radio Frequency Energy Your Motorola two-way radio complies with the following RF energy exposure standards and guidelines:
United States Federal Communications Commission, Code of Federal Regulations; 47CFR part 2 sub-part J. American National Standards Institute (ANSI)/Institute of Electrical and Electronic Engineers (IEEE) C95. 1-1992. Institute of Electrical and Electronics Engineers (IEEE) C95. 1-1999 Edition. International Commission on Non-Ionizing Radiation Protection
(ICNIRP) 1998. Ministry of Health (Canada) Safety Code 6. Limits of Human Exposure to Radiofrequency Electromagnetic Fields in the Frequency Range from 3 KHz to 300 GHz, 1999. Australian Communications Authority Radiocommunications
(Electromagnetic RadiationHuman Exposure) Standard, 2003. ANATEL ANNEX to Resolution No. 303 of July 2, 2002. ANATEL ANNEX to Resolution No. 533 of September 10, 2009. To ensure optimal radio performance and make sure human exposure to radio frequency electromagnetic energy is within the guidelines set forth in the above standards, always adhere to the following procedures. Portable Radio Operation and EME Exposure Antenna Care Use only the supplied or an approved replacement antenna. Unauthorized antennas, modifications, or attachments could damage the radio and may violate FCC regulations. Do NOT hold the antenna when the radio is IN USE. Holding the antenna affects its effective range. Body-Worn Operation To maintain compliances with FCC guidelines if you wear a radio on your body when transmitting always place the radio in a Motorola-supplied or approved clip holder, holster, case or body harness for this product. Use of non-Motorola-approved accessories may exceed FCC guidelines. If you do not use one of the Motorola-supplied or approved body-worn accessories and are not using the radio held in the normal use position, ensure the radio and its antenna are at least 1 inch (2.5 cm) from your body when transmitting. Data Operation If applicable, when using any data feature of the radio with or without an accessory cable, position the radio and its antenna at least one inch
(2.5 cm) from the body. Approved Accessories 53724: Remote Speaker with Push-to-Talk Microphone 53725: Headset with Swivel Boom Microphone 53727: Ear bud with Push-to-Talk Microphone 53728: Flexible Ear Receiver 56320: Earpiece with Boom Microphone Electromagnetic Interference/Compatibility Note: Nearly every electronic device is susceptible to electromagnetic interference (EMI) if inadequately shielded, designed or otherwise configured for electromagnetic compatibility. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference; and 2. This device must accept any interference received, including interference that may cause undesired operation. Facilities To avoid electromagnetic interference and/or compatibility conflicts, turn off your radio in any facility where posted notices instruct you to do so. Hospitals or health care facilities may be using equipment that is sensitive to external RF energy. Aircraft When instructed to do so, turn off your radio when onboard an aircraft. Any use of a radio must be in accordance with applicable regulations per airline crew instructions. Medical Devices Pacemakers The Advanced Medical Technology Association recommends that a minimum separation of 6 inches (15 cm) be maintained between a handheld wireless radio and a pacemaker. These recommendations are consistent with the independent research by and recommendations of the U.S. Food and Drug Administration. People with pacemakers should:
ALWAYS keep the radio more than 6 inches (15 cm) from their pacemaker when the radio is turned ON. Not carry the radio in the breast pocket. Use the ear opposite the pacemaker to minimize the potential for interference. Turn the radio OFF immediately if there is any reason to suspect that interference is taking place. Medical Devices Hearing Aids Some digital wireless radios may interfere with some hearing aids. In the event of such interference, you may want to consult your hearing aid manufacturer to discuss alternatives. Medical Devices Other If you use any other personal medical device, consult the manufacturer of your device to determine if it is adequately shielded from RF energy. Your physician may be able to assist you in obtaining this information. Safety and General Use While Driving Check the laws and regulations regarding the use of radios in the area where you drive, and always obey them. If you do use your radio while driving, please:
Give full attention to driving and to the road. Use hands-free operation, if available. Pull off the road and park before making or answering a call if driving conditions so require. The use of a two-way radio while engaged in activities requiring concentration may cause distraction or otherwise impair your ability to safely participate in such activities. Always use technology safely. Do not place a portable radio in the area over an air bag or in the air bag deployment area. Air bags inflate with great force. If a portable radio is placed in the air bag deployment area and the air bag inflates, the radio may be propelled with great force and cause serious injury to occupants of the vehicle. Potentially Explosive Atmospheres Turn off your radio prior to entering any area with a potentially explosive atmosphere. Only radio types that are especially qualified should be used in such areas as Intrinsically Safe. Do not remove, install or charge batteries in such areas. Sparks in a potentially explosive atmosphere can cause an explosion or fire resulting in bodily injury or even death. Note: The areas with potentially explosive atmospheres referred to above include fueling areas such as below decks on boats, fuel or chemical transfer or storage facilities, areas where the air contains chemicals or particles (such as grain, dust or metal powders) and any other area Date : Sept 15, 2010 Model : MS350R Description : Line Arts for User Guide Operational Cautions Antennas Do not use any portable radio that has a damaged antenna. If a damaged antenna comes into contact with your skin, a minor burn can result. Batteries All batteries can cause property damage and/or bodily injury such as burns if a conductive materiallike jewelry, keys or beaded chains touch exposed terminals. The conductive material may complete an electrical circuit (short circuit) and become quite hot. Exercise care in handling any charged battery, particularly when placing it inside a pocket, purse or other container with metal objects. Exercise care when removing NiMH or AA batteries. Do not use sharp or conductive tools to remove either of these batteries. Battery Charger Safety Instructions:
Save these Instructions 1. Do not expose the charger to rain or snow. 2. Do not operate or disassemble the charger if it has received a sharp Control Buttons blow, or has been dropped or damaged in any way. 3. Never alter the AC cord or plug provided with the unit. If the plug will not fit the outlet, have the proper outlet installed by a qualified electrician. An improper condition can result in a risk of electric shock. 4. To reduce the risk of damage to the cord or plug, pull the plug rather than the cord when disconnecting the charger from the AC receptacle. 5. To reduce the risk of electric shock, unplug the charger from the outlet before attempting any maintenance or cleaning. 6. Use of an attachment not recommended or sold by Motorola may result in a risk of fire, electric shock or personal injury. 7. Make sure the cord is located so it will not be stepped on, tripped over or subjected to damage or stress. 8. An extension cord should not be used unless absolutely necessary. Use of an improper extension cord could result in a risk of a fire and/or electric shock. If an extension cord must be used, make sure that:
The pins on the plug of the extension cord are the same number, size and shape as those on the plug of the charger. The extension cord is properly wired and in good condition. The extension cord size is 18 AWG for lengths up to 100 feet, and 16 AWG for lengths up to 150 feet. 9. The supply cord of the AC adaptor cannot be replaced. If the cord is damaged, call customer service at 1-800-638-5119 or e-mail us at giantintl@callcenter.com. FCC Licensing Information Your Motorola radio operate s on General Mobile Radio Service (GMRS) frequencies and is subject to the Rules and Regulations of the Federal Communications Commission (FCC). The FCC requires that all operators using GMRS frequencies obtain a radio license before operating their equipment. To obtain the FCC forms, please visit the FCCs Web site at wireless.fcc.gov/uls/index.htm?job=home to source form 605 and 159, which includes all the instructions you will need. If you wish to have the document faxed or mailed, or if you have questions, please use the following contact information:
Changes or modifications not expressly approved by Motorola may void the users authority granted by the FCC to operate this radio and should For a fax:
Contact the Fax-0n-Demand system For mail service:
Call the FCC Forms Hotline If you have questions about the FCC License:
Call the FCC 1-202-418-0177 1-800-418-FORM
(3676) 1-888-CALL-FCC
(225-5322) not be made. To comply with FCC requirements, transmitter adjustments should be made only by or under the supervision of a person certified as technically qualified to perform transmitter maintenance and repairs in the private land mobile and fixed services as certified by an organization representative of the user of those services. Replacement of any transmitter component (crystal, semiconductor, etc.) not authorized by the FCC equipment authorization for this radio could violate FCC rules. Note: Use of this radio outside the country where it was intended to be distributed is subject to government regulations and may be prohibited. Display Screen Guide Display Screen Guide Getting Started Waterproof Your radio is waterproof to IP-67 standards. It will withstand submersion under up to 1 meter of water for up to 30 minutes. The radio is resistant to water, rain, and splashes only when the battery cover and headset accessory port are sealed. Open the battery compartment door or headset port cover only when the radio is dry. Use of a headset accessory should be in dry environments only. The charging base and AC adaptor are not waterproof. Do not expose the charger to rain or snow. Charge the radios only in a dry location. Do not place wet radios into the charging base. Installing the Batteries Each radio can use either 1 NiMH rechargeable battery pack or 3 AA alkaline batteries and beeps when the batteries are low. Installing NiMH Rechargeable Battery Pack (Optional Accessory) 1. Turn the radio off. 2. With the back of the radio facing you, loosen the retaining screw on the battery door and open the cover. 3. Remove the NiMH battery pack from the clear plastic bag (do not 4. disassemble or unwrap the battery pack). Insert the NiMH battery pack with the diagram facing you. (The ribbon should be underneath the battery pack and should wrap around the right side of the pack for easy removal.) 5. Close the battery cover and tighten the retaining screw on the battery door. Installing the Three AA Alkaline Batteries 1. Turn the radio off. 2. With the back of the radio facing you, loosen the retaining screw on the battery door and open the cover. 3. Insert the three AA alkaline batteries with + and - polarity as shown Display Screen Guide inside. (The ribbon should be underneath the AA alkaline batteries and should wrap around the right side of the batteries.) 4. Close the battery cover and tighten the retaining screw on the battery door. Radio Battery Meter The radio battery icon shows the battery charge level, from full to empty
. When the radio has one segment left, the radio chirps periodically or after releasing
(Low Battery Alert). Removing the NiMH Battery Pack (Optional Accessory) 1. Turn the radio off. 2. With the back of the radio facing you, loosen the retaining screw on the battery door to release the battery cover and open the cover. 3. Remove the NiMH battery pack by pulling the ribbon attached to the radio. 4. Close the battery cover and tighten the retaining screw on the battery door. Removing the Three AA Alkaline Batteries 1. Turn the radio off. 2. With the back of the radio facing you, loosen the retaining screw on the battery door, release the battery cover and open the cover. 3. Gently remove each alkaline battery by easing each battery out individually. 4. Close the battery cover and tighten the retaining screw on the battery door. Notes Exercise care when removing NiMH or AA batteries. Do not use sharp or conductive tools to remove either of these batteries. Remove the batteries before storing your radio for extended periods of time. Batteries corrode over time and may cause permanent damage to your radio. The battery door must be tightly closed with the screw to maintain the waterproof seal of the radio. Using the Battery Charger (Optional Accessory) The battery charger provides drop-in charging convenience for NiMH batteries and can be placed on any flat surface, such as a desk or workbench. Charge the NiMH battery overnight (at least 16 hours) before using it for the first time. After the initial charge, an empty battery is fully charged within 14 hours. 1. Follow the steps above to install a NiMH Battery Pack. 2. Plug the AC power supply cord into the jack on the desk stand. 3. Plug the AC power supply into a standard wall outlet. 4. With a radio facing forward, slide it into one of the charging pockets. 5. When charging in the battery charger, the red light on the charger base will glow continuously. Notes The light will remain red after the NiMH battery pack is fully charged. When moving between hot and cold temperatures, do not charge the NiMH battery pack until the battery temperature acclimates (usually about 20 minutes). When the radio is wet from rain or snow, thoroughly dry the surface before charging or removing the batteries. For optimal battery life, remove the radio from the charger within 16 hours. Do not store the radio while connected to the charger. If the radio is kept on while charging, the charging time will be extended. Even though the charger is connected, you may not be able to transmit a message if the battery is completely empty Allow time for the battery to charge to 1 bar to transmit a message. before attempting
. Attaching and Removing the Belt Clip 1. Attach belt clip to pocket or belt strap. 2. Align the belt clip post with the hole in the back of the radio. 3. Gently push until the clip clicks in place. To Remove 1. Push down on the release tab at the top of the belt clip to release the catch. 2. Pull the belt clip away from the back of the radio. Turning your Radio On and Off Press and hold 1. for 3 seconds to turn the radio on or off. In the ON position, the radio chirps and briefly shows all feature icons available on the radio. 2. The display screen then shows the current channel, code and all features that are enabled. 3. Press and hold 4. Press and hold for 3 seconds to turn the radio on. for 3 seconds to turn the radio off. for three seconds, then press the Setting the Volume Press and hold you reach a comfortable listening level. The MS350 has 16 volume levels controlled by the 1. Press 2. Press 3. Hold to increase volume. to decrease volume. or to rapidly increase volume. or keys until keys. Do not hold the radio close to your ear. If the volume is set to an uncomfortable level, it could hurt your ear. alking and Listening Talking and Listening To communicate, all radios in your group must be set to the same channel and Interference Eliminator Code. 1. To talk, press and hold 2. When you are finished talking, release For maximum clarity, hold the radio two to three inches away from your mouth and speak directly into the microphone. Do not cover the microphone while talking. Talk Range Your radio is designed to maximize performance and improve transmission range. Do not use the radios closer than five feet apart. Power Boost To boost your radios power up to high power, press the top portion of the button when talking. If you know your party is close by, you can conserve your batterys energy by pushing the lower part of the button to use less power. Note: If you are on an FRS only channel (see Channels and Frequencies tables on overleaf for details) the radio will only use low power when either portion of the is pressed. for three seconds to latch on the MONITOR function. Monitor Button Press and hold Tap the a second time (while in the latched monitor condition) to close or turn off the MON function. You can also press to check for activity on the current channel before you talk. Timeout Timer Push to Talk To prevent accidental transmissions and save battery life, the radio emits a continuous warning tone and stops transmitting if you press for 60 continuous seconds. Menu Options Selecting the Channel Your radio has 22 channels plus 8 repeater channels. The channel is the frequency the radio uses to transmit. Channels 8-14 are FRS 0.5 watt only and all other channels are GMRS. (See the Channels and Frequencies tables on overleaf for details.) 1. With the radio on, press
. When the radio is on a 0.5 watt channel, displays. When the radio is on a 1.5 watts channel, displays. The current channel flashes. to continue set up. and select an unused or quiet channel. or to save the channel setting or 2. Press 3. Press The 8 repeater channels are disabled by default. See Enabling Repeater Channels on overleaf for information on setting the radio to a repeater channel. Selecting the Interference Eliminator Code Interference Eliminator Codes help minimize interference by blocking transmissions from unknown sources. Your radio has 121 Interference Eliminator Codes. Codes 1 38 are analog tones. Codes 39 121 are digital codes. 0 is the off position, no analog or digital codes are enabled
(see interference eliminator tone and code values table on overleaf). To set the code for a channel:
1. Press 2. Press 3. Press You can set a different code for each channel using this procedure. An extended press of Code rapidly so you can quickly reach the code you want. When setting codes for repeater channels 15R-22R, this code value is only used for receiving. The transmitted code can be set separately for repeater access. See Selecting the Repeater Access (TX) Code on overleaf for additional information. Note: You must set the Interference Eliminator Code to 0 to communicate with radios that do not have Interference Eliminator Codes. until the code starts to flash. or to select the code. to save the code setting or allows you to scroll through the Interference to continue set up. or Setting and Transmitting Call Tones Your radio can transmit different call tones to other radios in your group so you can alert them that you want to talk. Your radio has 10 call tones from which to choose, including 5 animal sounds and 5 regular call tones. To set a call tone:
1. Press three times until the current call tone setting flashes and appears. or to set the new call tone or to change and hear the call tone. 2. Press 3. Press To transmit your call tone to other radios set to the same channel and Interference Eliminator Code as your radio, press to continue set up. Continued on back MS350 Series Note: Setting the call to 0 disables the call tone feature. Hands-Free Use Without Accessories (
You can use the iVOX feature to transmit hands-free without the need for any headset accessories. Once iVOX is turned on, the radio detects your voice and transmits when you speak into the internal microphone. 1. Press appears on the display. The current setting
) until On/Off will flash. 2. Press 3. Press or to set or to select On or Off. to continue set up.
) Hands-Free Use With Accessories (
You can transmit hands-free more reliably with the use of optional headset accessories. Once VOX is turned on, the radio detects your voice and transmits when you speak. Many accessories (sold separately) are available for your radio. For more information, visit our Web site at www.motorola.com or shop.giantintl.com. 1. Turn the radio off and plug the VOX accessory into the accessory port. 2. Turn the radio on. VOX shows on the display. 3. Adjust the volume appropriately by pressing
. Lower the volume before placing the accessory on your head or in your ear. or 4. To turn off, simply remove accessory. Notes:
There is a short delay between the time you start talking and when the radio transmits. There is a short delay before the transmission is completed. Accessory port cover must be tightly in place to maintain the water tight seal of the radio. Setting the Sensitivity Level When in Adjusting the radios sensitivity level helps minimize the possibility of unintended noises triggering a transmission and helps the radio pick up soft voices. 1. Press until VOX and the level setting (1 - 3) appear on the Mode display. 2. Press 3. Press or to set or to select the sensitivity level. to continue set up. 3 = High Sensitivity for quiet environments 2 = Medium Sensitivity for most environments 1 = Low Sensitivity for noisy environments Note: When you connect a headset, the radio is automatically set to the last chosen sensitivity level. QT Noise Filtering The QT noise-filtering feature helps to ensure uninterrupted communication with other Motorola radios that have this feature. This feature also filters out unwanted transmissions from other radios. This is useful in places where there is heavy radio traffic, such as amusement parks or ski resorts. Note: QT noise filtering is not available when the radio is scanning. To turn QT noise filtering on or off:
1. Press 2. Press 3. Press To transmit to a radio that has QT noise filtering turned on:
1. Select the same channel and Interference Eliminator Code as displays. The current setting On/Off will flash. to turn noise filtering On or Off. until or to confirm your selection or to continue set up. the other radio. 2. Press to send a call tone. This allows your voice to pass through the QT noise filter on the receiving radio. and speak normally. 3. Press Note: If you skip step 2, the beginning of your message may not be heard on the receiving radio. For a 30-second period, starting after the last transmission, all transmissions received on the selected channel and code will pass through the QT noise filter. VibraCallTM Alert VibraCallTM is a vibrating alert that notifies you that your radio is receiving a message. This is useful in noisy environments. When the alert is on, the radio vibrates once every 30 seconds when you receive a message on the channel and code you set. 1. To turn vibrating alerts on, press until is displayed. The current setting will flash. 2. Press or to change the setting to On/Off. 3. Press to set or to continue set up. Keypad Tones You may enable or disable the speaker key tones. You will hear the key tone each time a button is pushed. 1. Press 2. Press either 3. Press appears. The current setting On/Off will flash. to continue set up. to turn On or Off. to confirm or until or Low battery alert tone or Note: When the key tone feature is off, the following are not disabled:
Transmit timeout alert tone Call tone The transmitted talk confirmation tone Transmitting a Talk Confirmation Tone You can set your radio to transmit a unique tone when you finish transmitting. It is like saying Roger or Over to let others know you are finished talking. Talk Confirmation Tone is disabled in repeater mode on channels 15R-22R. 1. With the radio on, press appears. The current setting until the On/Off flashes. 2. Press 3. Press or to set or to turn On or Off. to continue setup. Enabling Repeater Channels Use of a repeater can greatly increase the radio range and coverage area. Repeater use must be coordinated with the owner of the repeater. Be sure to understand and follow the sharing and usage rules for each repeater system. 1. With the radio on, press until the R appears. The current setting ON/OFF will flash. to select ON or OFF. or to save the setting or 2. Press 3. Press After enabling the repeater channels, you will be able to select channels 15R-22R. Refer to the Selecting the Channel section on page one. to continue set up. Selecting the Repeater Access (TX) Code When a repeater channel is selected, an additional menu option is available for setting the transmitted Interference Eliminator Code. Many repeaters will require a specific value setting to activate the repeater on your transmissions. See the table INTERFERENCE ELIMINATOR TONE / CODE VALUES for detailed information. 1. With the radio on, press repeatedly until the
, the R, and the current setting flash. or or to select the code. to exit menu mode. 2. Press 3. Press You can set a different code for each channel using this procedure. An extended press of Interference Code rapidly so you can quickly reach the code you want. 0 is the off position. allows you to scroll through the or Special Features Built-in Flashlight Press and hold the flashlight button to turn and keep the light on. The switch functions as a momentary control for the light. Note: Turn off the flashlight when not in use to conserve battery power. Keypad Lock To avoid accidentally changing your radio settings:
1. Press and hold 2. When in lock mode, you cannot turn the radio on or off, adjust the volume, receive, transmit, send a call tone, or monitor channels. All functions are locked. displays. until To unlock the radio, press and hold until is no longer displayed. Scanning Channels Use scan to search the 22 channels for transmissions from unknown parties, to find someone in your group who has accidentally changed channels, or to quickly find unused channels for your own use. There is a priority feature and 2 modes of scanning (basic and advanced) to make your search more effective. The basic scan mode uses the channel and code combinations for each of the 22 channels as you have set them (or with the default code value of 1). The Advanced Scan mode will scan all channels for any and all codes, detect any code in use, and use that code value temporarily for that channel. Priority is given to the home channel, that is, the channel (and Interference Eliminator Code) your radio is set to when you start the scan. This means the initial channel (and code setting) is scanned more often than the other 21 channels, and your radio will respond quickly to any activity occurring on the home channel as a priority. To start Scanning:
1. Briefly press the will appear in the display, and the key. The scan radio will begin to scroll through the channel and code combinations. 2. When the radio detects channel activity matching the channel and code combination, it stops scrolling and you can hear the transmission. 3. To respond and talk to the person transmitting, press within five seconds after the end of the transmission. 4. The radio will resume scrolling through the channels five seconds after the end of any received activity. 5. To stop scanning, briefly press the To start Advanced Scanning:
1. Set the Interference Eliminator Code to zero or OFF. 2. Briefly press the key. The scan key. will appear in the display, and the radio will begin to scroll through the channels. No Interference Eliminator Codes will filter what is heard. 3. When the radio detects channel activity with ANY code (or NO code), it stops scrolling and you can hear the transmission. Any Interference Eliminator Code that may be in use by that party will be detected and displayed. 4. To respond and talk to the person transmitting, press within five seconds of the end of the transmission. The radio will transmit using the newly detected Interference Eliminator Code. 5. The radio will resume scrolling through the channels five seconds after the end of any received activity. key. while the radio is scrolling through inactive 6. To stop scanning, briefly press the Scanning Notes:
1. If you press channels, the transmission will be on the home channel. Scanning will resume five seconds after the end of your transmission. You may press the If the radio stops on an undesired transmission, you may immediately resume the scan by briefly pressing If the radio repeatedly stops on an undesired transmission, you may temporarily remove that channel from the scan list by pressing and holding for three seconds. You may remove more than one channel in this way. key to stop scanning at any time. 2. 3. or or
. 4. To restore the removed channel(s) to the scan list, turn the radio off and then back on, or exit and re-enter the scanning mode by pressing
. 5. You cannot remove the home channel from the scan list. 6. In Advanced Scan, the detected code will only be used for one transmission. You must note the code, exit scan, and set that detected code on that channel to permanently use the detected code. Weather Receiver Your radio can tune in to broadcasts by the United States National Oceanic and Atmospheric Administration (NOAA) Weather Radio. You can listen to a weather channel (see Weather Channels and Frequencies table for details) or set your radio to alert you to emergency weather broadcasts that interrupt routine broadcasts. When you listen to a weather channel, you cannot use your radio in scan mode or for two-way communications. NOAA has transmitters located throughout the United States. These transmitters broadcast watches, forecasts, and other information 24 hours a day. Note: NOAA weather radio stations are assigned to cover specific areas and service may be limited. Please check with your local weather office for frequency and details, or visit www.weather.gov/nwr in the US to view the appropriate transmitter for your area. The use of the NOAA logo does not provide an endorsement or implied endorsement by NOAAs National Weather Service. Turning Weather Channel Reception On and Off 1. To turn weather reception on, press 2. To turn off, press Setting the Weather Channel Your radio receives weather frequencies:
1. After turning weather reception on, press and hold for 3 seconds. or turn the radio off and then back on. The current channel flashes. 2. Press or to select the appropriate channel with good reception in your area. to save the weather channel setting. 3. Press Setting the Weather Alert Your radio can be set to respond to NOAA Weather Radio emergency messages. A special alarm tone sounds an alert and turns on the weather receiver to give you immediate weather and emergency information. 1. After turning weather reception on, press twice. On/Off displays. 2. Press or to select On/Off. If you activate Weather Alert and return to two-way mode, will display. to save the Weather Alert setting. to return to two-way mode. 3. Press 4. Press As with two-way radio reception, weather channel reception depends on how close you are to a transmitter and whether you are indoors or outdoors. Because weather channels are transmitted without codes, they may contain static or noise. Weather Alert will not function while actively transmitting or receiving in two-way mode. FRS / GMRS SIMPLEX CHANNELS AND FREQUENCIES CHANNEL FREQ (MHz) TYPE CHANNEL FREQ (MHz) 1 2 3 4 5 6 7 8 9 10 11 462.5625 GMRS/FRS 462.5875 GMRS/FRS 462.6125 GMRS/FRS 462.6375 GMRS/FRS 462.6625 GMRS/FRS 462.6875 GMRS/FRS 462.7125 GMRS/FRS 467.5625 467.5875 467.6125 467.6375 FRS FRS FRS FRS 12 13 14 15 16 17 18 19 20 21 22 467.6625 467.6875 467.7125 462.5500 462.5750 462.6000 462.6250 462.6500 462.6750 462.7000 462.7250 TYPE FRS FRS FRS GMRS GMRS GMRS GMRS GMRS GMRS GMRS GMRS GMRS DUPLEX REPEATER CHANNEL FREQUENCIES CHANNEL RX (MHz) 462.5500 462.5750 462.6000 462.6250 15R 16R 17R 18R TX (MHz) CHANNEL RX (MHz) 462.6500 467.5500 462.6750 467.5750 467.6000 462.7000 462.7250 467.6250 19R 20R 21R 22R TX (MHz) 467.6500 467.6750 467.7000 467.7250 WEATHER CHANNELS AND FREQUENCIES CHANNEL RX (MHz) CHANNEL RX (MHz) CHANNEL RX (MHz) 161.775 161.750 162.000 WX9 WX10 WX11 WX5 WX6 WX7 WX8 162.450 162.500 162.525 161.650 162.550 162.400 162.475 162.425 WX1 WX2 WX3 WX4 INTERFERENCE ELIMINATOR TONE / CODE VALUES CODE 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38
(Hz) 67.0 71.9 74.4 77.0 79.7 82.5 85.4 88.5 91.5 94.8 97.4 100.0 103.5 107.2 110.9 114.8 118.8 123.0 127.3 131.8 136.5 141.3 146.2 151.4 156.7 162.2 167.9 173.8 179.9 186.2 192.8 203.5 210.7 218.1 225.7 233.6 241.8 250.3 CODE
(OCTAL) CODE
(OCTAL) 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 023 025 026 031 032 043 047 051 054 065 071 072 073 074 114 115 116 125 131 132 134 143 152 155 156 162 165 172 174 205 223 226 243 244 245 251 261 263 265 271 306 311 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 315 331 343 346 351 364 365 371 411 412 413 423 431 432 445 464 465 466 503 506 516 532 546 565 606 612 624 627 631 632 654 662 664 703 712 723 731 732 734 743 754 Patent and Copyright Information Manufactured, distributed or sold by Giant International Ltd., official licensee for this product. MOTOROLA, MOTOROLA SOLUTIONS and the Stylized M Logo are trademarks or registered trademarks of Motorola Trademark Holdings, LLC and are used under license. All other trademarks are the property of their respective owners. 2011 Motorola, Inc. All rights reserved. Warranty Consumer Two-Way Radio Products and Accessories purchased in the United States. What Does this Warranty Cover?
Subject to the exclusions contained to the right, Giant International Ltd. warrants the Motorola branded consumer two-way radios that operate via Family Radio Service or General Mobile Radio Service that it manufactures (Products), the Motorola branded or certified accessories sold for use with these Products that it manufactures
(Accessories) to be free from defects in materials and workmanship under normal consumer usage for the period(s) outlined below. This limited warranty is a consumers exclusive remedy, and applies as follows to new Motorola branded Products and Accessories manufactured by Giant International Ltd., and purchased by consumers in the United States, which are accompanied by this written warranty:
Who is covered?
This warranty extends only to the first consumer purchaser, and is not transferable. What will GIANT INTERNATIONAL LTD. do?
GIANT INTERNATIONAL LTD., at its option, will at no charge repair, replace or refund the purchase price of any Products or Accessories that does not conform to this warranty. We may use functionally equivalent reconditioned/ refurbished/ pre-owned or new Products, Accessories or parts. What Other Limitations Are There?
ANY IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, SHALL BE LIMITED TO THE DURATION OF THIS LIMITED WARRANTY, OTHERWISE THE REPAIR, REPLACEMENT, OR REFUND AS PROVIDED UNDER THIS EXPRESS LIMITED WARRANTY IS THE EXCLUSIVE REMEDY OF THE CONSUMER, AND IS PROVIDED IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED. IN NO EVENT SHALL MOTOROLA OR GIANT INTERNATIONAL LTD. BE LIABLE, WHETHER IN CONTRACT OR TORT (INCLUDING NEGLIGENCE) FOR DAMAGES IN EXCESS OF THE PURCHASE PRICE OF THE PRODUCT OR ACCESSORY, OR FOR ANY INDIRECT, INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES OF ANY KIND, OR LOSS OF REVENUE OR PROFITS, LOSS OF BUSINESS, LOSS OF INFORMATION OR OTHER FINANCIAL LOSS ARISING OUT OF OR IN CONNECTION WITH THE ABILITY OR INABILITY TO USE THE PRODUCTS OR ACCESSORIES TO THE FULL EXTENT THESE DAMAGES MAY BE DISCLAIMED BY LAW. Some states and jurisdictions do not allow the limitation or exclusion of incidental or consequential damages, or limitation on the length of an implied warranty, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights, and you may also have other rights that vary from state to state or from one jurisdiction to another. Products Covered Length of Coverage Exclusions Products and Accessories as defined above, unless otherwise provided for below. 1. Consumer Two-Way Radio Accessories. 2. Products and Accessories that are Repaired or Replaced. One (1) year from the date of purchase by the first consumer purchaser of the product unless otherwise provided for below. 1. Ninety (90) days from the date of purchase by the first consumer purchaser of the product. 2. The balance of the original warranty or for ninety (90) days from the date returned to the consumer, whichever is longer. Normal Wear and Tear. Periodic maintenance, repair and replacement of parts due to normal wear and tear are excluded from coverage. Batteries. Only batteries whose fully charged capacity falls below 80% of their rated capacity and batteries that leak are covered by this limited warranty. Abuse & Misuse. Defects or damage that result from: (a) improper operation, storage, misuse or abuse, accident or neglect, such as physical damage (cracks, scratches, etc.) to the surface of the product resulting from misuse; (b) contact with liquid, water, rain, extreme humidity, heavy perspiration, when the battery door or accessory port seals are not closed, sand, dirt or the like, extreme heat, or food; (c) use of the Products or Accessories for commercial purposes or subjecting the Product or Accessory to abnormal usage or conditions; or (d) other acts which are not the fault of Motorola or Giant International Ltd., are excluded from coverage. Use of Non-Motorola branded Products and Accessories. Defects or damage that result from the use of Non-Motorola branded or certified Products or Accessories or other peripheral equipment are excluded from coverage. Unauthorized Service or Modification. Defects or damages resulting from service, testing, adjustment, installation, maintenance, alteration, or modification in any way by someone other than Motorola, Giant International Ltd. or its authorized service centers, are excluded from coverage. Altered Products. Products or Accessories with (a) serial numbers or date tags that have been removed, altered or obliterated; (b) broken seals or that show evidence of tampering; (c) mismatched board serial numbers; or (d) nonconforming or non-Motorola branded housings, or parts, are excluded from coverage. Communication Services. Defects, damages, or the failure of Products or Accessories due to any communication service or signal you may subscribe to or use with the Products or Accessories is excluded from coverage. How to Obtain Warranty Service or Other Information?
To obtain service or information, please call:
USA Two-Way Radios 1-800-638-5119 giantintl@callcenter.com For Accessories, please call the telephone number designated above for the product with which they are used. You will receive instructions on how to ship the Products or Accessories at your expense, to a GIANT INTERNATIONAL LTD. Authorized Repair Center. To obtain service, you must include: (a) a copy of your receipt, bill of sale or other comparable proof of purchase; (b) a written description of the problem; (c) the name of your service provider, if applicable; (d) the name and location of the installation facility (if applicable) and, most importantly; (e) your address and telephone number. MS350 Series