60P 312.5W x 100H_mm 62.5W x 100H_mm M 1 2 GA-9660B x1 x1 USB x1 x1 1 2 1 2 3 Micro USB LED Micro-USB USB 1 Micro USB Micro USB USB 2 Micro-USB USB 1 Micro USB Micro USB 2 1 LED LED 2 GA-9660B9V 9V Assembly mode Connect to Laptop or Desktop to Charging Please install the base before using this product. 1 2 GA-9660B FAST WIRELESS CHARGER User Guide Dock x1 USB Cable x1 User Guide x1 Insert the charging plate into the slot in the direction of the arrow as shown in Figure 1 and Figure 2. About GA-9660B Package Contents GA-9660B Charges Board x1 Appearance User Guide Connect to Power Adapter Micro-USB USB Step 1: Insert the micro USB connector into GA-9660B, and connect USB-A with an adapter. Step 2: After the power is turned on, the LED indicator on the charging board blinks in blue and green and then turns off. GA-9660B goes into the standby mode. 1 2 Micro USB Port Wireless Charging Area 3 LED Indicator Micro-USB USB Step 1: Insert the micro USB connector into GA-9660B, and connect USB-A with a laptop or desktop. Step 2: After the power is turned on, the LED indicator on the charging board blinks in blue and green and then turns off. GA-9660B goes into the standby mode. Mobile phone charging right way Step 1: After the power is turned on, the LED indicator on the charging board blinks in blue and green and then turns off. GA-9660B goes into the standby mode. Step 2: When place the mobile phone with wireless charging function on the charging board, the LED indicator will turn into blue. GA-9660B is in charging mode. The LED indicator turns into green after the phone is fully charged. Note: At present, only Samsung mobile phones support full power feedback. Feedback is as mentioned above. After the rest of the mobile phone is fully charged, the charging board will not prompt. 5V 2A, 9V 1.67A 5V 1A, 9V 1.1A 110-205KHz 4-10mm 72%
130 x 72 x 10 mm 96g 1. 2. 3. 4. 5. 20cm 6.
*
NCC Specification Input: 5V 2A,9V 1.67A Output: 5V 1A, 9V 1A Frequency: 110-205KHz Receiving distance: 4-10mm Conversion: 72%
Size: 130 x 72 x 10 mm NW: 96g Cautions 1.Do not squeeze or collide 2.Do not disassemble or throw into fire or water, to avoid causing a short leakage. 3.Do not use wireless charger in severely hot, humid or corrosive environments, to avoid circuit damage and occurs leakage phenomenon. 4.Do not close with magnetic stripe or chip card (ID cards, bank cards, etc.) to avoid magnetic failure. 5.Pleased keep the distance at least 20cm between implantable medical devices (pacemakers, implantable cochlear, etc.) and the wireless charger to avoid potential interference with the medical device. 6.Take care of the children, to ensure that they wont play the wireless charger as a toy, to avoid unnecessary accidents GA-9660B DUAL COIL FAST WIRELESS CHARGER User Guide including interference that may cause undesired Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference and
(2) This device must accept any interference received, operation. This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. End-users and installers must be provide with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance.
*Power adapter is not provided. If you need, please purchase separately. www.gigastone.com