INSTALLATION INFORMATION FOR INSTALLERS WIRELESS POWER TRANSMITTER
(THROUGH SURFACE) Model Number: WPT503CM OF DOCUMENT IMPORTANT PURPOSE OF DOCUMENT THIS DOCUMENT IS FOR USE ONLY BY ORIGINAL EQUIPMENT MANUFACTURERS (OEMs) WHO PURCHASE THE REFERENCED TESLINK COMPONENTS FROM GILL ELECTRONICS, INCORPORATED OR ITS AFFILIATES (GILL). NEITHER THIS DOCUMENT NOR THE INFORMATION IN THIS DOCUMENT IS INTENDED FOR DISTRIBUTION TO, OR USE BY, END USERS OF OEM PRODUCTS WHICH INCORPORATE TESLINKTM COMPONENTS (END USERS). BY PURCHASING TESLINK COMPONENTS FROM GILL, EACH OEM ASSUMES, AND SHALL HAVE SOLE AND FULL RESPONSIBILITY FOR, PROVIDING APPROPRIATE INSTRUCTIONS FOR USE OF SUCH OEM PRODUCTS. GILL ASSUMES THAT ALL OEMs WHO PURCHASE FROM GILL AND WHO USE THIS DOCUMENT HAVE EXPERTISE IN THE USE OF ELECTRICAL DEVICES AND COMPONENTS, INCLUDING THE EXPERTISE NECESSARY TO (i) DETERMINE WHETHER OR NOT TESLINK COMPONENTS ARE SUITABLE FOR USE WITH THE OEMs PRODUCT, AND (ii) PROPERLY AND SAFELY CONFIGURE AND INSTALL TESLINK COMPONENTS. ACCORDINGLY, THIS DOCUMENT IS INTENDED ONLY AS A HELPFUL SUPPLEMENT FOR USE BY THE OEM AND NOT AS A SUBSTITUTE FOR THE OEMs EXPERTISE OR THE OEMs RESPONSIBILITY FOR PROPER AND SAFE DESIGN OF ITS PRODUCT AND INSTALLATION AND USE OF TESLINKTM COMPONENTS. IF ANY OEM USING THIS DOCUMENT LACKS SUCH EXPERTISE OR DOES NOT AGREE TO THE FOREGOING LIMITED PURPOSE STATED FOR THIS DOCUMENT, SUCH OEM SHOULD IMMEDIATELY NOTIFY GILL IN WRITING TO THAT EFFECT AND SHOULD NOT USE THIS DOCUMENT. PRICES AND OTHER TERMS AND CONDITIONS FOR SALE OF TESLINKTM COMPONENTS TO ANY OEM ARE GOVERNED BY SEPARATE DOCUMENTS ISSUED OR MADE AVAILABLE TO THE OEM BY GILL, INCLUDING THE INVOICE ISSUED BY GILL AND THE STANDARD TERMS AND CONDITIONS OF SALE. If you have need assistance or have questions, email techsupport@gill-electronics.com Page 1 SAFETY INFORMATION GILL EXPECTS THAT THE INSTALLER WILL INCLUDE APPROPRIATE SAFETY WARNINGS AND INFORMATION FOR END USERS OF ALL PRODUCTS WHICH INCORPORATE TESLINKTM INCLUDE THOSE SET FORTH BELOW AND OTHER WARNINGS AND INFORMATION AS THE INSTALLER DETERMINES NECESSARY AND APPROPRIATE. COMPONENTS. SUCH WARNINGS AND INFORMATION MUST DANGER To reduce the risk of electrical shock:
Always unplug the appliance from the electrical outlet before removing Do not reach for an appliance that has fallen into water unplug it immediately Do not disassemble or modify any part of this appliance Do not install this product in any ferrous, non-ferrous, or electrically conductive surface WARNING To reduce the risk of burns, fire, electrical shock, or injury to persons:
This product should not be used by children or persons with disabilities that may hinder their ability to understand all product information and use the product safely. Close supervision is necessary when this product is used near children or persons with disabilities Use this product only for its intended use as described in this manual Never operate this product if it has a damaged housing, cord, plug cable, or if wet Keep cord away from heated surfaces and liquid Do not operate where aerosol products are being used or oxygen is being administered This product is designed for indoor use only. Do not install or use this product outdoors Do not use this appliance with an extension cord or overloaded electrical outlet Do not place or leave metallic objects between the charging surface and device being charged This product should be kept a minimum of 35mm from all animate objects when in power transfer mode/charging mode. IMPORTANT SAFETY INSTRUCTIONS 1. SAVE THESE INSTRUCTIONS This manual contains important safety and operating instructions for resonant chargers Models: WPT503CM 2. Before using the resonant charger, read all instructions and cautionary markings on the resonant charger, power supply, and product using the resonant charger 3. CAUTION To reduce damage or risk of injury, charge only A4WP/ Rezence-certified products. If you have need assistance or have questions, email techsupport@gill-electronics.com Page 2 FCC & INDUSTRY CANADA COMPLIANCE C & INDUSTRY CANADA COMPLIANCE The installer shall inform end users of the following to the extent applicable:
This device complies with FCC/IC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines and RSS-102 of the IC radio frequency (RF) Exposure rules. This transmitter must not be co-
located or operating in conjunction with other antenna or transmitter. Changes or modifications not expressly approved by Gill Electronics, Incorporated could void the users authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna/device Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio/TV technician for help This Class B digital apparatus complies with Canadian ICES-001-V4. EUROPEAN DECLARATION OF CONFORMITY We, Gill Electronics, Incorporated, 5271 Plainfield Ave. NE. Grand Rapids, MI 49525, USA, declare under our sole responsibility that the product Wireless Power Transmitter - WPT503CM To which this declaration relates is in conformity with the following standard(s) or other normative document(s):
EN 55011 EN 300 328 EN 300 330 EN 301 328 EN 301 489 EN 609501 EN 61000-6-1 EN 62311 EN 60950 Following the provisions of Electromagnetic Compatibility, R&TTE Emissions, and Safety directive(s). The Technical Construction File is maintained at:
Gill Electronics Inc. 5271 Plainfield Ave. NE Grand Rapids, MI 49525 USA If you have need assistance or have questions, email techsupport@gill-electronics.com Page 3 SAFETY CONSIDERATIONS for INSTALLERS S The Installer is solely responsible for taking all steps necessary and appropriate for safe and proper installation of TeslinkTM products. Safety is dependent on a proper installation of a TeslinkTM installation. The Installer should read and fully understand this document prior to installation. The installer must have a good understanding of electrical procedures and systems, along with proficiency in the installation and service of commercial and residential work surfaces. There are no adjustments required at any time of the electrical components within the transmitter. Installers should not open the transmitter housings or make modifications to the TeslinkTM expressly approved in writing by an authorized representative of Gill Electronics, Incorporated. Any changes or modifications will void the product warranty. During Installation transmitter. The Installer should be properly trained and qualified for transmitter or components unless DO NOT connect this charger to an electrical outlet until:
1. ALL other electrical connections are made 2. Mounting of ALL components is complete 3. VERIFICATION that no short circuit exists in the entire system 4. VERIFICATION that transmitter is mounted in such a location and manner that no animate object, can in a normal manner of contact, come within 44mm of the bottom of a transmitter. (i.e. a transmitter mounted in a desk would be far enough away from the edge that if a person was sitting in a chair their thighs/knees would not be positioned with 44mm of the bottom of the transmitter). See ensuing illustrations for more details. 5. Ensure installation in a horizontal surface only. DO NOT install equipment or route wiring cords in the path of any walkways or moving components BEFORE drilling into the work surface, make sure that the equipment has no metal objects or structures within 1 around (XY) and within 2 below (Z). When drilling into the work surface, DO make sure that both sides of the surface are clear of anything that could be damaged The charging area on top of the work surface/furniture must be indicated in some manner After Installation Test the transmitter to ensure that it is working properly (see LED Indicator Light) File these instructions in a safe place and refer to them when performing maintenance or re-installing WARNING: Failure to follow all safety precautions and instructions may result in death, serious injury, or property damage. The installer assumes sole responsibility for such precautions and instructions and for any failure to follow them. I Disclaimer By proceeding with installation of Teslink components in products, the installer agrees that: (i) Gill is not liable under any theory of contract, tort law, or otherwise for any loss, damage, death, personal injury, special, incidental, or consequential damages, or any other damage of any nature arising directly or indirectly from or relating to the improper installation or use of Gill products or components in residential or office furniture or any other application; and (ii) the installer will defend, indemnify, protect, and hold harmless Gill and each of its affiliates, officers, directors, agents, and employees from and against any such liability, claims, injuries, losses, and damages. In order to safely install and use Gill products and components, full consideration of the work environment
(e.g., location of electrical wiring, support members, surface thicknesses, and other electrical and structural components) is required. Gill disclaims responsibility for improper use or installation of products or components and use or installation not consistent with the original manufacturer specifications and recommendations (if any) for such products or components. Warranty Information Neither this document nor the statements in this document create any warranties, express or implied, regarding Teslink products. All information regarding any warranties made by Gill to the purchaser of components is located in separate documentation provided by If you have need assistance or have questions, email techsupport@gill-electronics.com Page 4 Gill to the Installer. Gill makes no other warranties and specifically disclaims any express or implied warranties of merchantability or fitness for purpose. No warranty shall extend to any person other than the Installer who purchases the TeslinkTM SAFETY CONSIDERATIONS NSTRUCTIONS product from Gill. CERTAIN PRE-INSTALLATION CONSIDERATIONS The installer is solely responsible for taking all steps necessary and appropriate for safe and proper installation of Teslink components. These steps include, without limitation, the following:
Instruction and Personnel The installer should use only properly trained and qualified personnel for installation. The installer should assure that all such personnel read and fully understand this document prior to installation. See ensuing installation drawing and installation illustrations for detailed requirements. INSTALLATION INSTRUCTIONS Before discarding any packaging materials, check the TeslinkTM
(1) TeslinkTM Transmitter shipping carton and verify the following items are included:
(1) Power Supply WPT503CMFN If you have need assistance or have questions, email techsupport@gill-electronics.com Page 5 If you have need assistance or have questions, email techsupport@gill-electronics.com Page 6 POWER SUPPLY INFORMATION NFORMATION This TeslinkTM Through Surface Transmitter is supplied with a power supply having the following specifications:
Output Voltage: 36VDC 1.25A Input Voltage: 100 240VAC 50-60Hz Operating Temperature: 0C - +70C Country of Origin: China IMPORTANT Under no circumstances should the installer use or supply the end user with a power supply that was not originally provided with the TeslinkTM product. Gill Electronics package graphics and other marks are trademarks of Gill Electronics Inc. All other brand names are trademarks of their respective owners. Gill Electronics Inc. is not affiliated with the respective owners of their trademarks. TeslinkTM Electronics Inc. All rights reserved. is a trademark of Gill If you have need assistance or have questions, email techsupport@gill-electronics.com Page 7