INSTALLATION INFORMATION FOR CUSTOMERS & INSTALLERS WIRELESS POWER TRANSMITTER OF DOCUMENT Model Number: WPT171AT / WPT170AT IMPORTANT PURPOSE OF DOCUMENT COMPONENTS. BY PURCHASING TESLINKTM PRODUCTS FROM GILL, EACH CUSTOMER ASSUMES, AND SHALL THIS DOCUMENT IS FOR USE BY CUSTOMERS WHO PURCHASE THE REFERENCED TESLINKTM PRODUCTS FROM GILL ELECTRONICS, INCORPORATED OR ITS AFFILIATES (GILL). NEITHER THIS DOCUMENT NOR THE INFORMATION IN THIS DOCUMENT IS INTENDED FOR DISTRIBUTION TO, OR USE BY, END USERS OF GILL PRODUCTS WHICH INCORPORATE TESLINKTM HAVE FULL RESPONSIBILITY FOR, PROVIDING APPROPRIATE INSTRUCTIONS FOR USE OF SUCH OEM PRODUCTS. GILL ASSUMES THAT ALL CUSTOMERS WHO PURCHASE FROM GILL AND WHO USE THIS DOCUMENT HAVE EXPERTISE IN THE USE OF ELECTRICAL DEVICES AND COMPONENTS, INCLUDING THE EXPERTISE NECESSARY TO (i) DETERMINE WHETHER OR NOT TESLINKTM COMPONENTS ARE SUITABLE FOR USE WITH THE OEMs PRODUCT(S), AND (ii) PROPERLY AND SAFELY CONFIGURE AND INSTALL TESLINKTM PRODUCTS. FOR USE BY THE CUSTOMER AND NOT AS A SUBSTITUTE FOR THE CUSTOMERS EXPERTISE OR GILLS RESPONSIBILITY FOR PROPER AND SAFE DESIGN OF ITS PRODUCT AND INSTALLATION AND USE OF TESLINKTM PRODUCTS. IF ANY CUSTOMER USING THIS DOCUMENT LACKS SUCH EXPERTISE OR DOES NOT AGREE TO THE FOREGOING PURPOSE STATED FOR THIS DOCUMENT, SUCH CUSTOMER SHOULD IMMEDIATELY NOTIFY GILL IN WRITING TO THAT EFFECT AND SHOULD NOT USE THIS DOCUMENT. PRICES AND OTHER TERMS AND CONDITIONS FOR SALE OF TESLINKTM PRODUCTS TO ANY CUSTOMER ARE GOVERNED BY SEPARATE DOCUMENTS ISSUED OR MADE AVAILABLE TO THE CUSTOMER BY GILL, INCLUDING THE INVOICE ISSUED BY GILL AND THE STANDARD TERMS AND CONDITIONS OF SALE. THIS DOCUMENT IS INTENDED TO PROVIDE INSTALLATION AND USE REQUIREMENTS AND GUIDELINES FOR ALL SAFETY AND OPERATING REQUIREMENTS INCLUDING BUT NOT LIMITED TO ELECTRICAL AND RF EXPOSURE. THIS DOCUMENT IS AN INTEGRAL COMPONENT OF THE EQUIPMENTS AUTHORIZATION AND THE INSTRUCTIONS HEREIN ARE MANDATORY IN ORDER TO COMPLY WITH REGULATORY AUTHORIZATION. Page 1 If you have need assistance or have questions, email techsupport@gill-electronics.com SAFETY INFORMATION GILL REQUIRES THAT THE CUSTOMER WILL INCLUDE APPROPRIATE SAFETY WARNINGS AND INFORMATION FOR END USERS OF ALL PRODUCTS WHICH INCORPORATE TESLINKTM PRODUCTS. SUCH WARNINGS AND INFORMATION MUST INCLUDE THOSE SET FORTH BELOW AND OTHER WARNINGS AND INFORMATION AS THE CUSTOMER DETERMINES NECESSARY AND APPROPRIATE. DANGER To reduce the risk of electrical shock:
Always unplug the appliance from the electrical outlet before removing Do not reach for an appliance that has fallen into water unplug it immediately Do not disassemble or modify any part of this appliance Do not install this product in any ferrous or non-ferrous electrically conductive surface WARNING To reduce the risk of burns, fire, electrical shock, or injury to persons:
This product should not be used by children or persons with disabilities that may hinder their ability to understand all product information and use the product safely. Close supervision is necessary when this product is used near children or persons with disabilities Use this product only for its intended use as described in this manual Never operate this product if it has a damaged housing, cord, plug cable, or if wet Keep cord away from heated surfaces and liquid Do not operate where aerosol products are being used or oxygen is being administered This product is designed for indoor use only. Do not install or use this product outdoors Do not use this appliance with an extension cord or overloaded electrical outlet Do not place or leave metallic objects between the charging surface and device being charged This product shall be used strictly in accordance with the installation instructions contained within this document. IMPORTANT SAFETY AND COMPLIANCE INSTRUCTIONS 1. SAVE THESE INSTRUCTIONS This manual contains important safety and operating instructions for device that must be followed. Models: WPT171AT, WPT170AT 2. Before using the device, read all instructions and cautionary markings on the device, power supply and associated product(s) using the device 3. CAUTION To reduce damage or risk of injury, charge only A4WP/ Rezence-certified products. If you have need assistance or have questions, email techsupport@gill-electronics.com Page 2 FCC & INDUSTRY CANADA COMPLIANCE C & INDUSTRY CANADA COMPLIANCE The customer and installer shall inform end users of the following to the extent applicable:
This device complies with FCC/IC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines and RSS-102 of the IC radio frequency (RF) exposure rules only when installed according to the requirements in this installation document. Changes or modifications not expressly approved by Gill Electronics could void the users authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules when installed according to the instructions contained within this document. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna/device Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio/TV technician for help This Class B digital apparatus complies with Canadian ICES-001-V4. EUROPEAN DECLARATION OF CONFORMITY We, Gill Electronics, Incorporated, 5271 Plainfield Ave. NE. Grand Rapids, MI 49525, USA, declare under our sole responsibility that the product Wireless Power Transmitter WPT171AT/170AT to which this declaration relates is in conformity with the following standard(s) or other normative document(s):
EN 55011 (2011) / A1 (2011) EN 300 328 v 1.8.1 (2012-06) EN 301 489-1 V1.9.2 (2011) EN 301 489-17 V2.2.1 (2012) EN 301 489-34 V1.4.1 (2013) EN 300 330 EN 60950-1 Following the provisions of Electromagnetic Compatibility, R&TTE Emissions, and Safety directive(s). The Technical Construction File is maintained at:
Gill Electronics Inc. 5271 Plainfield Ave. NE Grand Rapids, MI 49525 USA If you have need assistance or have questions, email techsupport@gill-electronics.com Page 3 SAFETY AND COMPLIANCE CONSIDERATIONS S The customer is responsible for taking all steps necessary and appropriate for proper installation of TesLinkTM products to insure their safe operation including RF exposure requirements and all other applicable regulations. For the purpose of this document the installer is referred to as the person who is doing the actual installation of the TesLinkTM product. Safety is dependent on a proper installation of a TesLinkTM components within the transmitter. Do not open the transmitter housings or make modifications to the TesLinkTM transmitter or components unless expressly approved in writing by an authorized representative of Gill Electronics. Any changes or modifications will void the product warranty. During Installation product. There are no adjustments required at any time of the electrical DO NOT connect this charger to an electrical outlet until:
1. ALL other electrical connections are made 2. Mounting of ALL components is complete 3. VERIFYING that transmitter is mounted in such a manner that it is 19-30mm (~3/4 to 1-3/16) from the charging surface. 4. VERIFYING all installation drawing requirements are being adhered to. DO NOT install equipment or route wiring cords in the path of any walkways or moving components. BEFORE drilling into the work surface, make sure that the equipment has no metal objects or structures within 25mm (~1) around (XY) the charging area. When drilling into the work surface, DO make sure that both sides of the surface are clear of anything that could be damaged The charging area on top of the work surface/furniture must be indicated in some manner After Installation Test the transmitter to ensure that it is working properly (see installation instructions for LED indicator). File these instructions in a safe place and refer to them when re-installing. WARNING:
Failure to follow all safety precautions and instructions may result in death, serious injury, or property damage. The installer assumes responsibility for such installation precautions and instructions and for any failure to follow them. May cause interference with touch screen/pad for some electronic devices. If issue is noted cycle phone device power button to clear and do not use while charging. I Disclaimer By proceeding with installation of TesLink products, the installer agrees that: (i) except to the extent provided in 47 CFR 2.909 Gill is not liable under any theory of contract, tort law, or otherwise for any loss, damage, death, personal injury, special, incidental, or consequential damages, or any other damage of any nature arising directly or indirectly from or relating to the improper installation or use of Gill products or components in public, residential, or office furniture or any other application; and (ii) the installer will defend, indemnify, protect, and hold harmless Gill and each of its affiliates, officers, directors, agents, and employees from and against any such liability, claims, injuries, losses, and damages. In order to safely install and use Gill products and components, full consideration of the work environment (e.g., location of electrical wiring, support members, surface thicknesses, and other electrical and structural components) is required. Gill disclaims responsibility for improper use or installation of products or components and use or installation not consistent with the original manufacturer specifications and recommendations for such products or components. Warranty Information Neither this document nor the statements in this document create any warranties, express or implied, regarding TesLink products. All information regarding any warranties made by Gill to the purchaser of components is located in separate documentation provided by Gill to the customer. Gill makes no other warranties and specifically disclaims any express or implied warranties of merchantability or fitness for purpose. No warranty shall extend to any person other than the customer who purchases the TesLinkTM product from Gill. If you have need assistance or have questions, email techsupport@gill-electronics.com Page 4 CERTAIN PRE-INSTALLATION CONSIDERATIONS Gill Electronics is responsible for ensuring products meet all regulatory requirements and provide instructions to ensure a proper installation. The customer is responsible for taking all steps necessary and appropriate for safe and proper installation of actual TesLink products. See ensuing installation drawing for detailed requirements. WPT171AT / WPT170AT POWER SUPPLY INFORMATION NFORMATION This TesLinkTM through Surface Transmitter is supplied with a power supply having the following specifications:
Output Voltage: 12V 2A or 18V 1.5A Input Voltage: 100 240VAC 50-60Hz Operating Temperature: 0C - +70C Country of Origin: China IMPORTANT Under no circumstances should the installer use or supply the end user with a power supply that was not originally provided with the TesLinkTM product. Gill Electronics package graphics and other marks are trademarks of Gill Electronics Inc. All other brand names are trademarks of their respective owners. Gill Electronics Inc. is not affiliated with the respective owners of their trademarks. TesLinkTM Electronics Inc. All rights reserved. is a trademark of Gill If you have need assistance or have questions, email techsupport@gill-electronics.com Page 5