Vielen Dank fr den Erwerb unserer Produkte. In dieser Anleitung wird Ihnen kurz der Anschluss und das Koppeln mit ZigBee Light Link Gateways erlutert. Bitte lesen Sie diese Anleitung sorgsam bevor Sie den Artikel verwenden. Die Produkte sind mit vielen ZigBee Light Link Gateways* wie zum Beispiel Philips Hue, Osram Lightify** oder IKEA Tradfri*** kompatibel. Anschlieen:
1. Dafr das Kabel wie in Bild P1 vorbereiten, 9-10 mm des Kabels abisolieren und es sollte einen Querschnitt von 0,33-2,08mm (AWG22-14) haben. 2. Dann Drcken Sie mit einem Schraubendreher die Druckklemme nach unten und fhren das Kabel ein, siehe Bild P2. 3. Wenn Sie den Druck mit dem Schraubendreher wieder lsen, ist das Kabel verbunden. Beispiele zum Verbinden von verschiedenen LED Produkte mit den Steuergerten finden Sie in Bild P3-P7.
- P3 fr die Verwendung von RGBW bzw. RGBWW Produkten
- P4 fr die Verwendung von RGB Produkten, dafr wird die Klemme W einfach freigelassen
- P5 fr die Verwendung von einfarbigen Produkten, nur Dimmen, dafr werden die Klemmen R, G und B freigelassen
- P6 fr die Verwendung von RGB+CCT(Warmwei+Kaltwei) Produkten
- P7 fr die Verwendung von CCT(Warmwei+Kaltwei) Produkten Koppeln:
1. Schlieen Sie das Produkt an und bereiten Sie es zum Verwenden vor, siehe Abschnitt Anschlieen. 2. Starten Sie am ZigBee Light Link Gateway die Produktsuche, dies kann einen Moment dauern. (sollte es nicht gefunden werden, trennen Sie das Produkt vom Strom und verbinden es neu oder fhren Sie einen Reset durch) 3. Das Produkt wurde von dem Gateway gefunden und kann nun den gewnschten Zonen/Rumen/Gruppen zugeordnet werden. Siehe dazu die Anleitung vom Gateway. 4. Nun knnen Sie das Produkt wie gewnscht verwenden. Reset:
1. Schalten Sie das Produkt ein. 2. Nun Schalten Sie es aus und innerhalb von 2 Sekunden wieder ein, das ganze wiederholen Sie viermal. 3. Nach dem fnften Einschalten sollte das Produkt nun viermal Blinken um Ihnen anzuzeigen, dass der ResetVorgang abgeschlossen ist. 1. An 5. An 4mal Blinken An An Aus Innerhalb 2s
*Das RGBW Steuergert wird als 2 getrennte Gerte erkannt, eine RGB und eine einfarbige Lampe.
**Osram untersttzt nur eine ID, somit wird das RGBW Steuergert nur als RGB erkannt.
***IKEA untersttzt erst ab Ende des Jahres 2017 Farbwechsel Steuergerte. Thanks for buying our products. In this manual we will explain the connection of wires and the connection with a ZigBee Light Link Gateway. These devices works with many ZigBee Light Link Gateways* like Philips Hue, OsramLightify**
or IKEA Tradfri***. Wire Connection:
1. Please prepare the cable like picture P1 and strip the isolation to 9-10 mm. The cable cross-section must be between 0,33 and 2,08mm(AWG22-14). 2. Now push down the terminal with a screwdriver and put in the cable, see picture P2. 3. Take the screwdriver away and the cable is connected with the terminal. On picture P3-P7 you can see examples for the connection of different LED controllers:
- P3 for RGBW/RGBWW products
- P4 for RGB products, use a RGBW controller and dont connect the wire W
- P5 for single color LED product, use a RGBW controller and dont connect the wire R, G, B
- P6 for RGB+CCT(warmwhite+coldwhite) products
- P7 for CCT(warmwhite+coldwhite) products Connection with Gateway:
1. Connect the LED product to the controller see section wire connection. 2. Start the device searching on the ZigBee Light Link Gateway, it could take some time. If the Gateway does not find the device, plug power off/on or make a reset. 3. The Gateway found your device and you can assign it to the different rooms/zones/groups. 4. Now you can use the device. Reset:
1. Switch on your device. 2. Now switch off and on within 2 seconds. 3. Repeat off/on four times. 4. Reset is done when the device is switched on in the fifth time and the light stays on after blinking 4 times. 1sth on/off the 5th on blink 4 times on on off within 2s
*For RGBW/RGBWW devices you will find two SSIDs. One for white/warmwhite, the other for RGB.
**The Osram Gateway supports only one SSID, with the RGBW/RGBWW device it find only RGB.
***IKEA Gateway will support RGB devices till the end of the year 2017. Merci beaucoup pour lacquisition de nos produits. Dans ce mode demploi vous trouverez lexpliquation pour le branchement et la connexion avec ZigBee Light Link Gateways. Veuillez lire attentivement le mode demploi avant dutiliser le produit.Les produits sont compatibles avec de nombreux ZigBee Light Link Gateways*
comme par exemple Philips Hue, Osram Lightify** ou IKEA Tradfri***. Le branchement:
1. Pour cela, prparer le cble comme indiqu sur limage P1, dnuder 9-10mm du cable pour obtenir une coupe transversale de 0,33-2,08mm(AWG22-14). 2. Ensuite appuyer sur la borne avec un tournevis vers le bas et introduisez le cble, comme cest indiqu sur limage P2. 3. Lorsque vous supprimer la pression du tournevis sur la borne, le cble est alors raccord. Limage P3-P7 vous montre quelques exemples de connexion pour diffrents produits LED avec les commandes lectroniques
- P3 pour lutilisation des produits RGBW ou bien RGBWW
- P4 pour lutilisation des produits RGB, dans ce cas la borne lectrique W ne sera pas raccord
- P5 pour lutilisation des produits unicolores, rduire seulement lintensit lumineuse, pour cela les bornes lectriques R, G et B ne seront pas raccordes.
- P6 pour lutilisation des produits RGB+CCT (blanc chaud+blanc froid)
- P7 pour lutilisation des produits CCT (blanc chaud+blanc froid) Le couplage:
1. Brancher le produit et prparer le lutilisation, se confrer au branchement. 2. Commencer la recherche du produit sur ZigBee Light Link Gateway. Ceci peut durer quelques instants (si la recherche naboutit pas, dbrancher le produit, puis reconnecter vous ou procder un reset/rinisialisation). 3. Le produit a t repr par Gateway et dans ce cas il sera rpertori dans la zone ou le groupe souhait. Pour cela rfrez vous aux indications dans le mode demploi de Gateway. 4. Maintenant vous pouvez utiliser le produit comme il convient. Le reset:
1. Mettez le produit en marche. 2. Eteignez le produit et aprs 2 secondes rallumer le. Procder de la sorte quatre fois de suite. 3. A la cinquime mise en marche, le produit devra clignoter quatre fois pour indiquer que le reset a bien fonctionn. la premire fois Ouvrir/Fermer La cinquime fois Ouvrir Quatre fois de scintillation Ouvrir Ouvrir Fermer en moins de Deux secondes
*La commande lectronique RGBW est considre comme deux produits sparemment, une RGB et une lamp eunicolore.
**Osram ne fait que soutenir une ID, si bien que que la commande lctronique RGBW nest reconnue que comme RGB .
***IKEA ne soutriendra le systme de commande lctronique avec changement de couleur qu la fin de lanne 2017 P1 P2 P3 P4 P5 P6 P7 Wire preparation 0.33-2.08mm 9-10mm AC TO DC AC DC12~24V AC TO DC AC DC12~24V AC TO DC AC DC12~24V AC TO DC AC AC TO DC AC DC12~24V POWER1 POWER2 POWER1 POWER2 POWER1 POWER2 POWER1 POWER2 POWER1 POWER2
+
V R G B W
+
V R G B
+
V W
+
V W
+
V R G B C W
+
V W W
+
V W C WBGR+
+
BGR V+
W BGR+
C W V+
WW CW FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help. To assure continued compliance, any changes or modifications not expressly approved by the party. Responsible for compliance could void the users authority to operate this equipment. (Example- use only shielded interface cables when connecting to computer or peripheral devices). This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation. FCC Radiation Exposure Statement:
The equipment complies with FCC Radiation exposure limits set forth for uncontrolled enviroment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.