1 OVERVIEW 4. SIMPLE DIGITAL CONNECTION When connecting receiver to TV and VCR with RF cable (Single Antenna) Ww TV Antenna Satelite Antenna voR REIN FOUT EIN Kuri system Digital Receiver 20 2005 by Panarex Electronics OVERVIEW 1 5. ANALOG / DIGITAL CONNECTION When connecting receiver to analog receiver and VCR with RF Cable TV Antena Satelite Antenna WI Analoge Receiver vor PEIN AFOUT REIN 2005 by Panarex Electronics 21 PATE VEL) 1. Start Up It you are watching TV through the RF-cable, you need to adjust the Channel number. The type of TV and Channel numbers are set to PAL-G and Channel 38 at the factory, For USA, Ch.3 is factory preset Please follow the brief procedure below and watch the satellite programs.
(1) Select the language
(2) Select the antenna setup in main menu screen
(3) Adjust LNB configuration per each satellite
(4) Execute scanning to find program
(6) Exit from installation atter all programs are searched 1.1 Language When the receiver is turned on for the first time the language selection menu is appeared asin the Fig 1-1 Select the desired language and press OK to confirm it. This receiver supports 7 languages. English, German, French, {Fig 1-1]
Portugal, Spanish, Turkish, Arabic, Picture will be named by section number. 22 2005 by Panarex Electronics Creve 2. Installation Press the OK key. Antenna setup is appeared on screen as upper second figure. 2.1 Antenna Setup In this section you could know how to operate LNB set-up 2.1.1 Satellite
+ When you adjust the LNB set-up, you select the satellite using &b key.
+ After selecting the satellite, Press OK
+ Adjust LNB type, LNB Lo-Freg, 22kHz, DISEqC, LNB power, 0/12V, TP, Positioner Setting
+ You can cancel the satellite you chose using 4&D key, 2.1.2 LNB type Select LNB type using < > keys. There are 5 LNB alternatives.
+ Universal 1 (9750MHz & 10600 MHz)
+ Universal 2 (9750MHz & 10750 MHz)
+ Single-SL (5150MHz & 5750 MHz)
+ Single-SH (5150MHz & 5750 MHz)
+ Standard For USA 22kHz control is automatically set for each LNB alternative. If Universal 1 or 2is selected, 22kHz control should be off state. 2.1.3 LNB Lo-Freq If the required LNB frequency is not available, select "Standard and then enter the frequency manually using the numeric keys. For USA : C-Band L/O : 5150 MHz Ku-Band L/O : 10750 MHz 2005 by Panarex Electronics 23 PATE VEL) 2.1.4 22kHz. In case you are using a Oual LNB or two antennas connected to a 22kHz tone switch box, make 22kHz tone switch ON or OFF to select an LNB or an antenna. 2.4.5 DISEQC
+ DISEQC 1.0, 1.2, 1.3 (STAB USALS) is compatibe
+ DISEQC 2x1 & 4X1 is usually available. 2.1.6 Skew Jn case that LNB with mechanical polarizer is used in your system. Adjust skew value by using * 4/>key and check signal status bar at the same time. Keep on adjusting at the maximum signal status. 24.77 Select a specific transponder by using the VOL. 4 > keys. 2.1.8 Positioner Setting Iis used to set the DiSEqC 1.2 motor & USALS It you have no positioner equipment, Select Disable. Otherwise you can select either DiISEGC 1.2 or USALS, 1) DISEqc 1.2
(1) Current position Select the position number by using 4b keys (#0~#26: default define,
#27~H#49: users define)
(2) Movement Select East / West by using <> keys and press OK to stop
(8) Nudge East / West Select Nudge East / West by using > keys and press OK to save current position
(4) Recalculation It itis used to shift the position for al satelites Select Recalculation by using OK key and is makes above movement function
(5) East Limit Set Move the position to the most eastern position and press OK then East Limit is stored
(6) West Limit Set Move the position to the most western position OK then East Limit is stored
(7) Limits Disable Select Disable limits by using OK key 24 2005 by Panarex Electronics Creve
(8) Go to reference Select got to reference by using OK key 2) USALS (DiSEqC 1.3)
(1) Satellite Position It points out the position of saved satelite, You can change the position of the satelite by numeric keys
(2) My Longitude Please input Local Longitude by numeric keys
(3) My latitude Please input Local Latitude by numeric keys
(4) Reference position This is same as DiSEqC 1.2 Reference
(5) Move The satellite's position of (1) and the one calculated by value of (2) & (3) will be shown, Press OK key and it will move.
(6) Store Please select Store and the present position will be saved. 2.1.9 Satellite Scan After all LNB setting is finished, select and confirm Satelite scan, then channel searching is executed
# If you press SIG key on ACU, signal stmgth menu will be displayed on the screen, 2.2 Satellite scan Scan all the transponder of selected satellites.
(1) Press OK key and Select wanted satellite by using Waakey
(if you want to scan several satellites once, You can control by <> keys) Then press OK key to execute scanning
(2) You can select satellites whatever You chose though. It is possible to search only
{or 4 satellites among satellites you chose.
(3) Transponder will be consecutively scanned all selected satellites. 2005 by Panarex Electronics 25 2.3 TP scan Selected TP is scanned in this menu
(1) Select TP scan in the installation menu
(2) Select a satellite
(8) Select TP to scan by using the ay key (using <> keys you can multiscan), then press OK to search 2.4 Network Scan Procedure for setting up is same as TP scan Advantage: when TP information is updated, updated information should be scanned 2.5 Advanced Scan Advanced Scan is used to scan the new TP of which the parameters have been entered manually. After setting the search parameters like down frequency, symbol rate and polarity by using the numeric keys and VOL 4 keys, press a Setting Video PID/Audio PID/PCR PID
* You can set the PID to search program,
+ After setting the PID values, press OK key. 2.6 Smart Search 2.6.1 How to add a new satellite 1. Select the satellite name with <>
keys, 2. if you want to add a new satellite, press the OK key, 2.6.2 LNB Configuration Please refer to 4.1 Antenna Setup 2.6.3 Symbol range elect Full, High or Low + Full: High and Low
+ High >7.5M + Low :<7.5M 2.6.4 Polarity
+ Select Horizontal / Vertical with 4 > keys,
+All Scan Horizontal and Vertical
+ Horizontal : Scan Horizontal TP only.
+ Vertical : Scan Vertical TP only. 2.6.5 Scan
+ Select Scan type with 4 > keys.
+ When you select the OK key, the scanning will start 26 2005 by Panarex Electronics Creve 2.7 Edit TP/ Satellite In this mode, you can add the New- Satellite and the new transponder information Also you can update or delete the transponder information 2.7.1 How to add a new satellite
* Select New in the satellite name the using the numeric key or CH aw key, Press VOL 4b keys to move digit.
+ Maximum number of characters is 12-digit.
+ Press OK key.
+ Enter the Down frequency, Symbol Rate and LNB Polarity,
+ Press EXIT or OK key, the new transponder information is stored. 2.7.2 How to rename the satellite
+ Press OK after selecting a satelite of which you want to change name.
+ Select Rename in the menu.
+ Enter new name by using numeric key or CH &W Keys and press OK key. 2.7.8 How to Delete/Restore a satellite
+ Press OK key after selecting a satelite you want to delete.
+ Press OK to confirm, otherwise press EXIT to cancel. The color of the deleted satelite name in the lst is changed.
+ The satelite which has had already searched channels cannot be deleted.
+ To restore the deleted satelite, move the cursor to the deleted satelite and press OK key. Then select Restore in the screen and press OK key. 2.7.4 How to add a new transponder
+ Ptess OK alter selecting a satelite
+ Select Eait TP and then Transponder lst is shown
+ Press OK key selecting "NEW in the transponder list
+ Enter the Down frequency, Symbol Rate and LNB Polarity
+ Press EXIT or OK, the new transponder information is stored 2.7.5 How to delete or update a transponder added
+ Press OK key after selecting a satellite
+ Select Edit TP, then transponder list is shown
+ Select a transponder you want to delete or update
+ Press OK on the TP you want to Edit or Delete
+ You can see the Euit or Delete in the small-menu
+ In case you want to Edit alist TP Select EDIT and press "OK key Enter Down frequency, LNB polarity and Symbol Rate and press EXIT or OK Then New TP date is automatically updated
+ In case you want to Delete a TP Select Delete in the small menu, press OK key Then the TP selected is deleted 2005 by Panarex Electronics 27 PATE VEL) 3. Parental Control Alter selecting Parental control and entering the correct password, the screen as shown in the right appears. The default password at the factory is 0-0-0-0"
You may change the PIN code, which is your password in other words, and lock the receiver to prevent children from watching selected programs 3.1 Change PIN Code You can change the PIN Code (Password) if you want.
(1) Enter the Old password, If you enter this mode for the first time after purchasing the receiver, the OLD PIN Code is the default password
(2) Enter the new password.
(3) Reenter the new password to confirm Warning! You must remember the New password because it is used in several Funetion as follows. Password is required
(1) To show parental locked channels.
(2) To enter Parental Control menu
(3) To enter channel edit menu
(4) To execute factory setting 28 2005 by Panarex Electronics
(eve 4, Channel Edit In this mode.
(1) You can sort the channels out upon your Preference.
(2) You can rearrange the channel list.
(3) You can delete channel
(4) You can adjust the favorite channel list, as required
(6) You can skip channels.
(6) You can change the channel name, as you want
(7) To enter channel edit mode, you need to press 4 digit password (factory setting is "0-0-0-0") 4.1 How to sort the channel
(1) Press OK after selecting Sor.
(2) Sub mode will be appeared as follows,
* Alphabetic
+ Satelite
+ FTAScramble
+ P-Lock
(3) Select the mode among the 4 kinds of mode that you want to sort and press OK
(4) Press EXIT to exit from this mode. Note The Format of Sorted List
+ Alphabetic & Satelite: In Alphabetical order
+ FTA/Scramble: The Free channels first & the scrambled channels later and vice-versa,
+ P-Lock: The channels of P-Lock first 4.2 How to move the channel
(1) Press the OK key after Selecting Move' key
(2) Press OK to select a channel to move and then move the selected channel to the new position by using CH &W keys.
(3) Repress OK key. 2005 by Panarex Electronics 29 PJ 30 OPERATION 4,3 How to delete the channel
(1) Select Delete and press OK.
(2) Select a channel you want to delete by using the 4 bkey.
(8) Press OK key.
(4) All channels that you selected are deleted 4.4 How to store/release the favorite channel
(1) Select Favorite and press "OK."
(2) Press OK, then this channel is included to the favorite channel ist
(3) The mark stands for the favorite cannel,
(4) To delete a channel from the favorite list, go to the marked channel and Press "OK"
4.5 How to lock/unlock the channel
(1) Select P-LOCK in the screen as shown and press OK.
(2) Select the channel that you want to lock and press OK
(3) This channel is now locked and the symbol of lock will be shown as a locked channel
(4) You can release the locked channel if you press OK after selecting the locked channel
(5) Once locked channel is selected while watching television, password is requested,
(6) Picture and sound is appeared after the correct password is given by pressing the numeric key. 4.6 How to SKIP the channel
(1) Select "SKIP" and then press "OK"
(2) Select the channel you want to hide
(3) Press OK 4.7 How to rename the channel
(1) Press OK after selecting RENAME mode
(2) Select the channel of which you want to change name
(8) Press OK to enter the character input mode.
(4) Put new names, as you want using the 4 arrows keys and numeric key. The maximum number of characters is 20.
(6) Alter completion of entering new, press OK 2005 by Panarex Electronios 5. User Setup In this USER SETUP mode, you can select the sub-mode as shown on the [Fig 6] by pressing the OK key and CH av key, The changed set-up is activated and stored by pressing the EXIT key. 5.1 Language Press the EXIT key affer you select your preferable language by using VOL <>
key. English, German, French, Portugal, Spanish, Turkish, Arabic, Croatia 5.2 Aspect ratio You can set the TV aspect ratio (4:3 for normal TV & 16:9 for wide TV) by pressing VOL 4 keys 5.3 TV Type (USA Standard is NTSC) You can set the TV type (PAL, NTSC and AUTO) by pressing VOL 4 P keys. I the setting value is Auto, then TVis set automatically by source program So, the source program is PAL, TV set PAL source program is NTSC, TV set NTSC. 5.4 Time Setting Aer selecting the Time Setting, you can adjust the time. Also you can set the wakeup time and sleeping time to turn receiver on and off automatically according to the time programmed. 2005 by Panarex Electronics 3 PATE VEL) 5.5 Modulator If you want to watch the broadcasting through, the modulator output, you could change the modulator channel as follows atter pressing the OK key to enter the sub-menu
(1) NTSC is supported
(2) You can adjust the Modulator type by pressing VOL 4 > key.
(3) You can adjust Modulator type, you can go back to the previous mode by pressing EXIT or OK key.
(4) The adjusted data is programmed automatically when the EXIT key is pressed,
(6) Modulator channel can be changed from the channel 8 to channel 4. 1) Set TV channel to 3 and find menu screen, 2) Select modulator column and change the channel number by 4 Key. 8) Press "EXIT" key to store and menu screen is appeared. 4) Tune TV channel to the channel newly stored as in the above. 5.6 OSD setting You can adjust the transparency level by using > key. 5.7 Data Transfer (Receiver to Receiver) 1) Connect Null Modem RS 232 Cable
(Pin #2 & 3 twisted) between master and slave receiver. 2) Leave the slave receiver power on condition all the time until completion of date transfer. 8) Hook up the master receiver to the TV and select SW Transfer" at User Setup"
screen. 4) Select Ver Code or Ch Data" by using Vol 4 or Vol button. Then press CH" button to start transfer. During data transfer, processing percentage wil be displayed on the screen Warning! Do not disturb data transfer by touching any Remote button, RS232 Cable, IF Cable, RCA Cable etc, during data transfer period until Please wait for saving message disappeared, Interuption of data transfer could damage the receiver's flash memory chip which makes the receiver dead and void warranty. 32 2005 by Panarex Electronics 6. Factory Setting Once the Factory setting is selected and the correct password is given by pressing 4-digit numeric keys followed by OK key, whole parameters are changed to the value written in the factory. That is, factory setting functions your STB (Set Top Box) the first stage. If you do not want to continue this mode, press EXIT key before you enter password. System Information Shows the information of model name, data and version of STB. 8. Channel List
+ you can see the channel list as shown in the above figure by pressing OK key
+To watch another channel, move the cursor to the channel you want by using
> keys AY PG J PG | and press Ok key
+ If favorite channels are saved, the list is changed from channel list TV to favorite list
+ Pressing TV/RADIO key change from channel list to channel list Radio You can exit from the channel list menu by pressing EXIT key or "OK" key. 2005 by Panarex Electronics 33 OPERATION 9. Program Guide
+The title and start time of the program is shown as in the right figure after pressing EPG key.
+ Select the particular channel you. The channel will be changed.
+ Ifyou want to watch TV with full screen, Press EXIT, 10. Audio change
+In_ multilingual program, favorite language is selected by passing AUDIO key and CH aw keys
+ Audio mode (L-left, R-right, L/R-stereo) can be Changed By pressing AUDIO key and VOL 4b key. 11. Recall the Favorite channel
+ Press the FAV key to recall a stored favorite channel,
+ Favorite channel is programmed and stored in the channel edit menu. 12. Download Procedure between Pansat 2700A & PC 1. Turn the receiver power on. 2. Connect Null Modem RS232C cable (#283 twisted) between PC and the receiver. 8. Open the GTRom Loader. 4, Press Browse and select the Bin fle to be download, 5. Select the File type and press Download, 2005 by Panarex Electronios Creve 6 Wait until Download and the receiver Flash write are fully completed Warning: Do not interrupt the receiver power until download and flash write are tully completed. Otherwise the receiver will be damaged or dead. 2005 by Panarex Electronics ie ~ 35 tonal item) UHF Receiver on the condition that AC power cord of the WARNING : To prevent electrical shortage, do not install the A Satellite Receiver is plugged in. 3.1. KIT LIST 1. UHF Receiver 2 UHF Antenna 8. UHF Remote Control 4. Battery(AAA Type) - 2pcs, 3.2 INSTALLATION, 1. Take off the AC power plug of the Satellite Receiver from the wall socket. 2, Connect the UHF antenna to ANT IN. 8. Connect the Cable Assembly to the UHF RX IN on the rear of the Satelite Receiver. 4, Plug the AC powercord and tur on the receiver. 5. Use UHF Remote Controller. = tz 38 |Rcu THE REAR OF UHF RECEIVER ANT IN UHF RX IN oo THE REAR OF SATELLITE RECEIVER
(o] >
3.3 SPECIFICATION UHF Receiver FREQUENCY BOOM
| MODULATION MODE | FSK UHF INPUT LEVEL. 958m
(SENSITIVITY) WHIP ANTENNA Tika SIZE(mm) 65x 96195, UHF Remote Control INDOOR USE About 6Omm OUTDOOR USE About 200m BATTERIES(AAA Type) | 1 5V x 2pes. 36 2005 by Panarex Electronics Tuner/Channet Input connector F-ype, IEC 169-24 IF input Frequency 950MH2 to 2150MH2
|F Loop through out 950M to 21502 IF Froquoncy Zoro-iF Input Love! *65d8m ~-2568m LNB power 13/18V DC, 5OOmA Max DISEqC Control Version 1.3 Compatible Band Switching 22KH2 Tone Demodulation cPsk Symbol Rate 145Msps
(scP, MoPo) Viterbi Decoding Rata 1/2, 27% 24,515, 78 eed Sclomon Decoding FEC : 204,188, t=8 DiseqC 1.3 Compatible
(STAB USALS) MPEG Transport Stream & A/V Decoding Demutiplex Acoocding to ISOMEC 138181 Input Steam Max, SOMbitS Aspect Ratio 43,169 Vidoo Resolution 720x578 Audio Decoding MPEG Layer | and i Audio Mode SinglerDual Channel, Stereo, doin Stereo Sampling Frequency 16,22.05,24,92,44.1, Kriz Microprocessor & Memories ___ Main Processor STIS518BVB, ST20 320i CPU Clock ai MHZ Flash Memory 2 Mbyte SDRAM 8 Mbyte EEPROM 32 Kbit SPECIFICATIONS 4 Data Port Connector 9Pin D-sub Type Protoco! 18282 Asynchronous Data Rato Max. 19.2kbps RF Modulator __ Connector EC 169-2, MalefFemate Frequency 470Me2 to 860NHZ OUtput channel CH 3-4 TV Standard NTSC Preset channel Changeable by Menu Screen Front Panel _________ 4Digits LED Display Channel Number Display 3 Keys Power, Channel Down and Channel UP, Rear Panel
|F input F-type Connector
|F Loopthrough output F-ype Connector 4PhonaCinch Video, Audio L, Auio SPF Skew 3 Push Terminal
(GY, GND, PULSE) SvHS Super Video Output Modulator S232 Seral Port 9 Pin D-sub Type Fomote Control Type Ina Red
(Carter Freq :38kH2) Battery 2x 1.5V AAA Type Others Input Vatage "AC90-250V, 50/6042 Power Consumption Max. 25 Watts Slandby Power Lass Than 5 Watts Dimension 290 x 200 x 65mm 2.1Kg 2005 by Panarex Electronics 37 TROUBLE SHOOTING =
There may be various reasons for the abnormal of the unit. Therefore, if the unit does not work properly. check the unit according to the procedures shown in the table below. Problem Possible causes Remedy LED on front pane! | AC power cord Connect power cord properly does notlight | disconnected into the power socket No Picture or | Wrong connection of the | Connect two terminals correctly sound video/audio output to TV with scart cable or RCA or RF input terminal cable
\Wrong connection of Connect the antenna cable satellite antenna cable correctly Wrong direction of satellite | Adjust the direction of antenna antenna No signal or weak signal | Check the cable connections, LINB and other equipment connected between the LNB and]
the receiver or adjust the antenna Wrong setting of channel _| Type the setting value correctly information in MENU screen Black-and-white | Your TV mode is different _| Use TV of same mode screen of V-Hold | from satellite broadcasting mode Use the NTSC/PAL converter connected to the receiver and v The remote Battery exhausted Change the batteries controller is not working Fluorescent light interfering | Switch off the light with the remote controller Remote controller is Am the remote control atthe incorrectly aimed receiver Distorted menu | Too high brightness and _| Adjust brightness and contrast to screen contrast level of TV set _| low level Not working Process Down Remove the power code or AC switch OFFION 38 2005 by Panarex Electronics