FCC ID: S3KTO41XX LTE Outdoor CPE

TITAN4000 LTE Outdoor CPE Quick User Guide V1.0 PLEASE READ THESE SAFETY PRECAUTIONS!

FCC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This device complies with Part 15 of the FCC Rules. Operation is subject to the

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause FCC Warning following two conditions:

undesired operation. NOTE 1: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help. NOTE 2: Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. 2 1. Overview The TITAN4000 is highly innovative and patented LTE outdoor CPE product designed to enable quick and easy LTE fixed data service deployment for residential and SOHO customers. It provides high speed LAN services to end users who need both bandwidth and multi-media data service in enterprise or home. It can also be used to support wireless fall back service. 1.1. User Interface Specification Model Description & User Interface TITAN4000

- 1 RJ45 10/100/1000M LAN port

- SYS, MOD, SIM, ETH, Wi-Fi, RF (5 Signal intensity LEDs)

- PoE DC 48V, Power < 18 Watts (Average)

- Dimensions: 300 mm (L) 290 mm (W) 97 mm (D)

- Weight: <5Kg

- Operating Temperature: -40 to 55

- Storage Temperature: -40 to 85 3 Upon receiving the product, please unpack the product package carefully. Each product is 2. Getting Started 2.1. Packing list and CPE Unit shipped with the following items:

Table 2-1 Packing List Products CPE Unit Clamp Mounting brackets PoE Adapter Power cord 1.5M Quick user guide Quantity 1 2 1 1 1 1 If you find any of the items missed, please contact your local distributor immediately. 2.2. Installing the Equipment Open the SIM card cover, insert the SIM card and connected the ETH cable. TheusershoulduseSFTPCAT5EEthernetcableandconnecttotheappropriate LANport 4 Mounting Bracket Using clamps to fixed. 5 Device logic connection LED Display LED Function Description SYS System run indicator Solid green Device is in normal operation. MOD WAN port status OFF NO wireless network access. Solid Green WAN data transmission in progress SIM SIM card indicator Light is on SIM card state is ready, Blinking Green SIM card is error. ETH LAN port status Solid Green LAN port is up. Blinking Green LAN port in working. Wi-Fi Wi-Fi indicator Light is on Wi-Fi is on. RF

(5LEDs) RF Signal Strength 5 level signal strengths indication by 5 green LEDs. 1st Green LED: -115dBm < RSRP 2nd Green LED: -115dBm <= RSRP < -105dBm 3rd Green LED: -105dBm <= RSRP < -95dBm 4th Green LED: -95dBm <= RSRP < -85dBm 5th Green LED: -85 <= RSRP 6 3. Managing the CPE Device 3.1. WEB Login User can access the dongle management GUI using a Web browser from a local PC connected to device LAN port. The user should ensure that the connected PC have acquired IP address via DHCP from the device. After IP connectivity is established between the PC and window CPE device, the user may launch a Web browser and specify Http://192.168.0.1 in the address bar, the default home page will appear. Note the default password is admin. 7 3.2. System configuration DMZ This menu allows user to configure the DMZ setting for CPE in router mode. Web server, Telnet/SSH and Ping Service port can be exempted from DMZ mapping if required. By enabling DMZ option will make the specified local LAN host (DMZ IP) exposed to Internet. Security This page allows user to configure the security setting. Applications This menu allows user to configure the port forwarding rules for the CPE in router mode. 8 Maintenance and reboot the device. This page allows user to update the device firmware version, rest the device to factory setting 4. Troubleshooting Q1: My PC cannot connect to the CPE. Check the PoE adapter LED is on and your PC LAN port is working. Q2: My CPE networking is not working properly. Check and make sure you are within LTE coverage. Q3: Unable to connect internet while the device is already connected to LTE network. Check and verify your computer has the ETH adapter installed and enabled. Unplug the PC Lan port and reconnect again if required. 9

Reference No.: WTX21X04032055W-1/2 Page 1 of 17 ANNEX EXHIBIT 1 - PRODUCT LABELING Proposed FCC ID Label Forma Specifications: The label shall be securely affixed to a permanently attached part of the device, in a location where it is visible or easily accessible to the user, and shall not be readily detachable. The label shall be sufficiently durable to remain fully legible and intact on the device in all normal conditions of use throughout the devices expected lifetime. Proposed Label Location on EUT FCC ID Label Location Waltek Testing Group (Shenzhen) Co., Ltd. Http://www.waltek.com.cn

Global Telecom Corp 17901 Von Karman Ave, suite 600, Irvine 92614, California, United States

Date: 2021-05-18 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 FCC ID: S3KTO41XX Confidentiality Request To whom it may concern, Block Diagram Operational Description Schematics Parts List Pursuant to Sections 0.457 and 0.459 of the Commissions Rules, we hereby request confidential treatment of the information accompanying this application as outlined below:

Tune-Up Information Security Information Software Defined Radio (SDR) Information The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, Global Telecom Corp

(Ahmad Malkawi)

(Sr. Vice President Business Development)

Global Telecom Corp 17901 Von Karman Ave, Suite 600, Irvine, California 92614 United States Federal Communications Commission Authorization and Evaluation Division 1435 Oakland Mills Road Columbia, MD 21046 Date: 2021-05-18 SUBJECT: FCC Application for FCC ID: S3KTO41XX To Whom It May Concern:

I, the undersigned, hereby states this equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules, and will apply the Supplier's Declaration of Conformity procedure to Part 15 Class B Digital Device. I understand the following FCC requirements:

1. Devices subject to the SDoC procedure are required to be tested to show compliance with the FCC technical regulations by a recognized accredited testing laboratory. The testing laboratory must be accredited by a Commission approved accreditation body or designated under the terms of a government-to-government Mutual Recognition Agreement (MRA). A listing of those accredited testing laboratories that have been recognized by the Commission is published on the FCC Webpage: https://apps.fcc.gov/oetcf/eas/reports/TestFirmSearch.cfm (Select the

"accredited" option to search for FCC recognized accredited test firms.) 2. Pt 2.1077 contains the list of information that must be included in the Supplier's Declaration of Conformity, which must be supplied with each product sold. The SDoC compliance info shall be included in the Users Manual or as a separate sheet. The info must contain the name, address, and phone number of the responsible party, which must be located within the United States. According to 2.909(b), the responsible party is either the Manufacturer or if the product is imported the Importer. Regards, Global Telecom Corp

(Ahmad Malkawi)

(Sr. Vice President Business Development)

Global Telecom Corp 17901 Von Karman Ave, suite 600, Irvine, California, 92614, United States

(FCC IDS3KTO41XX) POWER OF ATTORNEY DATE: 2021-05-18 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 To Whom It May Concern:

We, the undersigned, hereby authorize Waltek Testing Group (Shenzhen) Co., Ltd. Jandy So on our behalf, to apply to the Federal Communications Commission on our equipment. Any and all acts carried out by Waltek Testing Group (Shenzhen) Co., Ltd. Jandy So on our behalf shall have the same effect as acts of our own. This is to advise that we are in full compliance with the Anti-Drug Abuse Act. We, Global Telecom Corp are not subject to a denial of federal benefits pursuant to Section 5301 of the Anti-Drug Act of 1988, 21 USC853a, and no party to the application is subject to a denial of federal benefits pursuant to that section. Sincerely, Global Telecom Corp

(Ahmad Malkawi)

(Sr. Vice President Business Development)