ON/OFF SWITCH Smart User Guide ON/OFF SWITCH INTENDED USE This product is intended to be used as a wall switch to control incandescent and Led light bulbs as part of permanent xtures. It is intended to replace a standard switch receptacle. It can be connected and controlled through a WI-FI connection with the Amazon Alexa app or other external Alexa built-in devices. FEATURES Replace existing on/off or dimmer switches and make them smart Manually or remotely control your wall switch with the Amazon Alexa app Pair with Amazon echo to control your switch through voice commands Set schedules and control your switch from anywhere SPECIFICATION Switch type Wiring Rated input voltage Input Voltage Range Maximum Load Standby Power Start up Time Single pole + 3-Way Wire to wire connection Neutral wire is required 120Vac / 60Hz 108-132Vac Incandescent: 600W max. LED: 150W max.
<0.5W
<1 second ON/OFF SWITCH Step-by-step Product Instruction Video Intended for household use only Intended to be used in dry indoor areas only Thank you for selecting Globe as your smart home solution. With proper care, this product will provide years of pleasure and enjoyment. Scan with your mobile device SAVE THESE INSTRUCTIONS Most electrical accidents are caused by carelessness or ignorance. If you combine a basic knowledge of electricity, a healthy respect for it, and a dose of common sense, you can safely tackle many household electrical repairs. Here are some basic guidelines for working with electricity:
Before working on a circuit, go to the main service panel and remove the fuse or trip the breaker that controls that circuit. Tape a sign to the panel warning others to leave the circuit alone while you work. Before touching any wire, use a voltage tester to make sure its not live. Whenever you check for voltage in a receptacle, check both outletseach may be controlled by a separate wiring circuit. To protect children, place safety covers over any unused outlets. Always work with enough light to see what you are doing; its easy to make mistakes when youre working in dim light. Before assembling your smart switch xture, TURN OFF THE POWER and consult a qualied licensed electrician. This Smart Switch is warranted to last 1 year from the date of purchase. If it fails before that time, we will replace it. Send Globe Electric the Smart Switch, proof of purchase and register receipt along with your complete name and address. See caution text for proper use. This warranty is void if this product is misused in any way. This replacement is the sole remedy available and liability for incidental or consequential damage is expressly excluded. For use only in 120V/60HZ circuits. Risk of electrical shock. Do not open, no user-serviceable parts inside. This device is not intended for use with emergency exit xtures or emergency exit lights, photocells and electronic timers. Do not use where directly exposed to water. If this situation is undesirable for the application, follow the manufacturers instructions for replacing the device. Minimum operating temperature is
-20C (-4F). RF Exposure The equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This device should be installed and operated with minimum distance 20cm between the radiator & your body. User Manual Notice for LicenseExempt Radio Apparatus This device complies with Industry Canada licenseexempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. CAN ICES-005 (B). Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. WARNING: Changes or modications to this unit not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. FCC Responsible party Globe Electric 15301 Shoemaker Ave, Norwalk, CA 90650 www.globe-electric.com This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modications not expressly approved by the manufacturer could void the users authority to operate the equipment. Wireless Control Module Wi-Fi 2.4GHz, IEEE 802.11 b/g/n Bluetooth Low Energy Does not support 5GHz networks, BLE only for pairing the phone and device Status Indicator On/Off switch Main unit 50586 PRE-INSTALLATION STATUS INDICATOR & CONTROLS Planning Installation Compare all parts with the Hardware Included section. If any part appears missing or damaged, do not install this product and contact the Customer Service team at 1-888-543-1388 or e-mail to info@globe-electric.com. Tools Required Status Indicator Light Red and Green blinking alternately Factory reset is complete Green Blinking Amber Indicator is off Solid Green for 3 seconds Red blinking Solid Red Ready for setup/
Setup is in progress Light is off Light is on Device registered and connected No Network Setup has timed out On/Off Buttons Short press power button (<1s) Turn the light on/off Press and hold power button (>10s) Factory reset Enter pairing mode phillips head screwdriver pliers electrical tester at head screwdriver INSTALLATION Hardware Included NOTE: Hardware is not shown to actual size. WARNING:Improper wiring of any electrical device can cause re, serious injury or death. Always consult a qualied licensed electrician who will ensure the switch is installed in accordance with local electrical codes and regulations. Before starting installation, ensure the power is disconnected at the circuit breaker and test existing switch with a voltage tester. Caution Make sure that the power at the circuit breaker is off before wiring. Neutral wire is required. Conrm the wall box contains a neutral wire (typically white). The wire colours indicated in this manual are the common colors and may differ in some homes. Please contact an electrician if you have different wire colours. Ensure the wire conductors are securely fastened to each wire. If missing, look for a bundle of white wires folded in the back of the switch box. Most homes bult after 1978 have neutral wires. 50586 Single pole connection refers to when 1 light is controlled by 1 switch. The Traveler (brown) wire is not needed for this scenario. SINGLE POLE For lights switched from ONE location. For retrot applications. 1. Remove the existing wall plate and screws from the wall after having turned off the power at the circuit breaker and tested the outlet with a voltage tester. 2. Remove the existing switch from the wall and label the wires with the appropriate stickers included in the box. 3. Ensure these wires are available:
a. Line (black b. Ground (green, or yellow/green c. Neutral (white) x2 d. Load (red) 4. Disconnect the wiring from the old switch. 5. Connect the WI-FI on/off switch to the existing wiring:
a. Connect Ground (Green, A) wire on the switch to the Ground
(green) wire from the switch box b. Connect the Line (Black, D) wire on the switch to the Line (Black) wire from the breaker box c. Connect the Neutral (White, B) wire on the switch and the Neutral
(white) wire coming from the light to the Neutral (White) wire from d. Connect the Load (Red, E) wire on the switch to the Load (red) 6. Ensure the included wire nuts are securely fastened to each wire. The Traveler (brown, C) wire needs to be covered with a wire nut even if the breaker box wire from the light not in use screws provided. 7. Insert the new switch into the wall. Cover with the wall plate and 3-WAY For retrot applications. For lights switched from TWO locations. 1 SMART SWITCH 1. Remove the existing wall plate and screws from the wall after having turned off the power at the circuit breaker and tested the outlet with a voltage tester. 2. Remove the existing switch from the wall and label the wires with the appropriate stickers included in the box. 3) Ensure these wires are available a. For Smart Switch:
i. Line (black ii. Ground (green, or yellow/green iii. Neutral (white) x2 iv. Load (red) v. Traveler (Brown) b. For Standard on/off switch:
i. Line (black ii. Ground (green, or yellow/green iii. Traveler (Brown) 4. Connect the Wi-Fi switch (model 50586) to the existing wiring (See Wiring Diagram) 5. Connect the WI-FI on/off switch to the existing wiring:
a. Connect Ground (Green, A) wire on the switch to the Ground (green) wire from the standard switch then to the Ground (Green) wire from the b. Connect the Line (Black, D) wire on the switch to the Line (Black) wire from the standard switch and then to the Line (Black) wire from the c. Connect the Neutral (White, B) wire on the switch and the Neutral
(white) wire coming from the light to the Neutral (White) wire from the breaker box. breaker box. breaker box. the light d. Connect the Load (Red, E) wire on the switch to the Load (red) wire from e. Connect the Traveler (Brown, C) wire on the switch to the Traveler
(brown) wire from the existing switch. 6. Ensure the included wire nuts are securely fastened to each wire. 7. Restore power at the circuit breaker switch to test if the switch works. 8. Insert the new switch into the wall. Cover with the wall plate and screws provided. 2 SMART SWITCHES NOTE: to produce a functional 3-way connection, both smart switches need to be the same brand. This switch is not compatible with other brands. For retrot applications. 1. Remove the existing wall plate and screws from the wall after having turned off the power at the circuit breaker and tested the outlet with a voltage tester. 2. Remove the existing switch from the wall and label the wires with the appropriate stickers included in the box. 2 1 Smart Switch #1 Smart Switch #2 (wired to light xture) i. Line (black) ii. Ground (green, or yellow/green) iii. Neutral (white) iv. Traveler (Brown) i. Line (black) ii. Ground (green, or yellow/green) iii. Neutral (white) x2 iv. Load (red) v. Traveler (Brown) 1. Connect Ground (Green, A) wire of both switches to the Ground (green) wire from the breaker box. 2. Connect the Line (Black, D) wire of both switches to the Line (Black) wire from the breaker box. 3. Connect the Neutral (White, B) wire on the switch 2 and the Neutral (white) wire coming from the light to the Neutral (White) wire from the breaker box. 4. Connect the Neutral (White, B) wire on the switch 1 to the Neutral (white) wire coming from the breaker box. 5. Connect the Load (Red, E) wire on the switch 2 to the Load (red) wire from the light 6. Connect the Traveler (Brown, C) wire on the switch 2 to the Traveler
(brown) of the switch 1. 7. Ensure the included wire nuts are securely fastened to each wire. 8. Restore power at the circuit breaker switch to test if the switch works. 9. Insert the new switch into the wall. Cover with the wall plate and screws provided. INSTALL WALL PLATE 1. Insert the On/Off switch into the switch box. DO not pinch any wires and ensure they are arranged neatly. 2. Ensure the On/Off switch has the Up marking facing up and attached to the switch box with the 2 screws (M). 3. Place the back piece over the On/Off switch and secure with the 2 screws (N). 4. With the top marking facing up, snap on the screwless faceplate on the On/Off switch. This Smart Switch is warranted to last 1 year from the date of purchase. If it fails before that time, we will replace it. Send Globe Electric the Smart Switch, proof of purchase and register receipt along with your complete name and address. See caution text for proper use. This warranty is void if this product is misused in any way. This replacement is the sole remedy available and liability for incidental or consequential damage is expressly excluded. For use only in 120V/60HZ circuits. Risk of electrical shock. Do not open, no user-serviceable parts inside. This device is not intended for use with emergency exit xtures or emergency exit lights, photocells and electronic timers. Do not use where directly exposed to water. If this situation is undesirable for the application, follow the manufacturers instructions for replacing the device. Minimum operating temperature is
-20C (-4F). RF Exposure This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modications not expressly approved by the manufacturer could void the users authority to operate the equipment. The equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This device should be installed and operated with minimum distance 20cm between the radiator & your body. User Manual Notice for LicenseExempt Radio Apparatus This device complies with Industry Canada licenseexempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. CAN ICES-005 (B). Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. WARNING: Changes or modications to this unit not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. FCC Responsible party Globe Electric 15301 Shoemaker Ave, Norwalk, CA 90650 www.globe-electric.com 1. Download the Amazon Alexa app. INSTRUCTIONS DE CONNEXION 2. Power on your device. Ensure your smart switch is installed correctly and powered on. QR 3. Scan barcode Launch the Amazon Alexa app. Select Add a Device. Please keep these instructions in a safe place. This is the only duplicate of the unique QR code for your product. You may need it to reconnect the product to your account or transfer it to another account. Select Smart switch, locate Globe Electric and follow the in-app instructions on how to scan the 2D barcode. Please note:
The device is automatically in pairing for 5 minutes once powered on. When you scan the barcode, the white light will ash indicating the pairing is successful. If within 5 minutes, it does not connect, turn the device OFF and ON again to re-enter pairing mode. Dont have a barcode?
Select "Don't have a barcode?" in the Alexa app and follow the in-app instructions on how to connect without a 2D barcode. How to factory reset device If you are struggling to set up your device, or if the device was already connected to a network, perform a factory reset by following the 50457 instructions below:
1. Turn the device ON 2. Press and hold the ON/OFF button down for 10 seconds. 3. Let go of the button once the light is ashing RED and GREEN indicating a successful reset. Check out product videos on our Youtube channel, from the Globe x Amazon Alexa -
Smart Devices playlist. INTERRUPTEUR MARCHE/ARRT Smart User Guide Travaillez toujours avec sufsamment dclairage pour voir clairement ce que vous faites; il est facile de commettre des erreurs en travaillant la lumire tamise Puissance dentre nominale 120 VCA / 60 Hz Avant de monter le luminaire, COUPEZ LE COURANT et consultez un lectricien agr quali. Plage de tension dentre 108 132 VCA INTERRUPTEUR MARCHE/ARRT Merci d'avoir choisi Globe comme solution pour votre maison intelligente. Avec un entretien appropri, ce produit vous procurera des annes de plaisir et de satisfaction Tutoriel vido tape par tape du produit Balayez avec votre appareil mobile CONSERVEZ CES INSTRUCTIONS La plupart des accidents dorigine lectrique sont causs par la ngligence ou lignorance. Avec une connaissance de base de llectricit, un respect de ses principes et un peu de gros bon sens, vous pouvez effectuer en toute scurit plusieurs rparations lectriques rsidentielles. Voici quelques consignes de base pour les travaux dlectricit :
Avant de travailler sur un circuit, ouvrez le panneau lectrique et retirez le fusible ou dclenchez le disjoncteur associ ce circuit. Mettez une tiquette sur le panneau avisant les autres personnes de ne pas toucher au circuit pendant que vous y travaillez, Avant de toucher un l, utilisez un voltmtre pour vrier sil est sous tension. Mesurez toujours la tension dans les deux prises dun boitier, car elles pourraient tre relies des circuits distincts. An de protger les enfants, insrez un capuchon de scurit dans toute prise de courant non utilise. Cet Interrupteur Intelligent est garantie pour une dure de 1 an compter de la date dachat. En cas de dfaillance durant la priode de garantie, nous la remplacerons. Faites parvenir la Interrupteur Intelligent, la preuve dachat, le reu de caisse, ainsi que vos nom et adresse complets Globe lectrique. Lisez attentivement la notice de mise en garde avant dutiliser la Interrupteur Intelligent. Cette garantie sera nulle et sans effet en cas dusage inadquat. Le remplacement est le seul et unique recours offert et toute responsabilit pour dommages accessoires ou conscutifs est expressment exclue. Convient uniquement aux circuits de 120V/60Hz. Risque dlectrocution. Ne pas ouvrir. Ne renferme pas de pices dont lentretien peut tre assur par lutilisateur. Ne convient pas aux voyants et lampes de sortie durgence, aux rcepteurs photolectriques, ni aux minuteries lectroniques. Ne pas utiliser dans un endroit o il y a risque dexposition directe leau. Si les appareils branchs ncessitent une protection contre les surtensions, suivez les directives du fabricant pour le remplacement du dispositif. La temprature de fonctionnement minimale est de -20C (-4F). Ce dispositif est conforme aux dispositions de la section 15 des rgles de la FCC. Son utilisation est assujettie aux deux conditions suivantes : (1) le dispositif ne doit pas occasionner de brouillage prjudiciable et (2) lutilisateur du dispositif doit tre dispos accepter tout brouillage reu, mme si ce brouillage est susceptible de compromettre le fonctionnement du dispositif. Toute modication nayant pas t expressment approuve par le fabricant pourrait annuler le droit de lutilisateur de faire fonctionner ce dispositif. Exposition aux radiations :
Cet quipement est conforme aux limites d'exposition aux rayonnements FCC tablies pour un environnement non contrl. Cet quipement doit tre install et utilis avec un minimum de 20cm de distance entre la source de rayonnement et votre corps. Notice d'utilisation de matriel radio exempt de licence Le prsent appareil est conforme aux CNR dindustrie Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes: 1) Iappareil ne doit pas produire de brouillage; et 2) Iappareil doit accepter le brouillage radiolectrique subi mme si le brouillage est susceptible den compromettre le fonctionnement. CAN ICES-005 (B). Dclaration d'exposition aux radiations :
Cet quipement est conforme aux limites d'exposition aux rayonnements IC tablies pour un environnement non contrl. Cet quipement doit tre install et utilis avec un minimum de 20cm de distance entre la source de rayonnement et votre corps. AVERTISSEMENT : L'utilisateur qui modie ou altre ce produit sans autorisation expresse de lautorit comptente pourrait perdre le droit de lutiliser. N.B. : Ce produit a t valu et jug conforme aux limites xes pour les appareils numriques de classe B selon la partie 15 des rglements de la FCC. Ces limites visent assurer une protection raisonnable contre le brouillage prjudiciable en milieu rsidentiel. Partie responsable FCC Globe lectrique 15301 Shoemaker Ave, Norwalk, CA 90650 www.globe-electric.com UTILISATION PRVUE Ce produit est conu pour tre utilis comme un interrupteur mural an de contrler les ampoules incandescence et DEL dun luminaire permanent. Il remplace les interrupteurs et prises standard. Il peut tre connect un rseau Wi-Fi et contrl laide de lapplication Alexa dAmazon ou dautres appareils externes intgrs dAlexa. Pour usage domestique seulement. Pour usage lintrieur dans un endroit sec seulement. CARACTRISTIQUES Remplace les interrupteurs existants par un systme intelligent Contrle manuel ou distance de linterrupteur laide de lapplication Alexa dAmazon Couplage avec les produits Echo dAmazon pour contrler linterrupteur par la voix Programmation de minuteries et contrle de linterrupteur de nimporte o SPECIFICATION Type dinterrupteur Unipolaire (mettre en gras et en gros caractres) Cblage Connexion l--l Fil neutre requis (mettre en gras et en gros caractres) Consommation dnergie maximale 600 W max. Puissance dentre maximale Ampoule incandescence : 600 W Ampoule DEL : 150 W Consommation en veille
< 0,5 W Temps de dmarrage
< 1 seconde Module de commande sans l Connexion Wi-Fi de 2,4 GHz, IEEE 802.11 b/g/n Bluetooth basse consommation Non compatible avec les rseaux de 5 GHz;
Bluetooth basse consommation seulement pour le couplage du tlphone et de lappareil Indicateur de statut Interrupteur marche/arrt Unit principale 50586 PR-INSTALLATION INDICATEUR D'TAT ET COMMANDES Prparation de linstallation Comparer le contenu de lemballage avec la section Quincaillerie comprise . Si des pices sont manquantes ou endommages, ne pas installer le produit et Outils ncessaires communiquer avec le service la clientle : 1 888 543-1388 ou info@globe-electric.com. Voyant dtat Rouge et vert, clignotant Rinitialisation acheve Vert, clignotant Ambre Voyant teint Prt pour la conguration /
conguration en cours Luminaire teint Luminaire allum Vert, xe pendant 3 secondes Appareil enregistr et connect Rouge, clignotant Aucune connexion rseau Rouge, xe Short press power button (<1s) Press and hold power button (>10s) Conguration expire Allumer/teindre le luminaire Rinitialiser activer le couplage Tournevis pointe cruciforme Pince Appareil de mesure lectrique Tournevis tte plate On/Off Buttons Matriel inclus NOTE : La quincaillerie n'est pas reprsente sa taille relle. INSTALLATION ATTENTION: Le cblage inadquat de tout appareil lectrique pourrait occasionner un incendie, des blessures graves ou la mort. Veillez toujours consulter un lectricien agr quali qui sassurera que le boitier est install conformment au code et la rglementation lectrique locale. Avant de procder linstallation, assurez-vous que lalimentation lectrique est coupe au disjoncteur et vriez le courant dans l'interrupteur avec un voltmtre. Mise en garde Assurez-vous que l'alimentation du disjoncteur est coupe avant de raccorder les ls. Un l neutre est requis. Conrmez que le boitier mural contient un l neutre
(gnralement blanc) Les couleurs de l indiques dans ce manuel sont les couleurs courantes et peuvent diffrer dans certaines maisons. Veuillez contacter un lectricien si vous avez des couleurs de ls diffrentes. Assurez-vous que les conducteurs des ls sont solidement xs chaque l S'il n'y en a pas, cherchez un faisceau de ls blancs pli l'arrire de la bote de commutation. La plupart des maisons construites aprs 1978 ont des ls neutres. 50586 For retrot applications. 1. Remove the existing wall plate and screws from the wall after having turned off the power at the circuit breaker and tested the outlet with a voltage tester. 2. Remove the existing switch from the wall and label the wires with the appropriate stickers included in the box. 3) Ensure these wires are available a. For Smart Switch:
i. Line (black ii. Ground (green, or yellow/green iii. Neutral (white) x2 iv. Load (red) v. Traveler (Brown) b. For Standard on/off switch:
i. Line (black ii. Ground (green, or yellow/green iii. Traveler (Brown) 4. Connect the Wi-Fi switch (model 50586) to the existing wiring (See Wiring Diagram) 5. Connect the WI-FI on/off switch to the existing wiring:
a. Connect Ground (Green, A) wire on the switch to the Ground (green) wire from the standard switch then to the Ground (Green) wire from the b. Connect the Line (Black, D) wire on the switch to the Line (Black) wire from the standard switch and then to the Line (Black) wire from the c. Connect the Neutral (White, B) wire on the switch and the Neutral
(white) wire coming from the light to the Neutral (White) wire from the breaker box. breaker box. breaker box. the light d. Connect the Load (Red, E) wire on the switch to the Load (red) wire from e. Connect the Traveler (Brown, C) wire on the switch to the Traveler
(brown) wire from the existing switch. 6. Ensure the included wire nuts are securely fastened to each wire. 7. Restore power at the circuit breaker switch to test if the switch works. 8. Insert the new switch into the wall. Cover with the wall plate and screws provided. UN SEUL PLE La connexion unipolaire dsigne un (1) luminaire actionn par un
(1) interrupteur. Pour ce type de connexion, le l de navette (brun) nest pas requis. Pour la rnovation :
1. Retirez du mur la plaque murale existante ainsi que les vis aprs avoir mis lalimentation hors tension 2. Retirez le gradateur existant du mur et apposez les tiquettes autocollantes appropries sur les ls (comprises dans la boite). Pour les lumires allumes partir d'UN seul endroit. 3. Sassurer que les ls suivants sont disponibles :
a. 1 l de phase (noir) b. 1 l de mise la terre (vert, ou jaune/vert) c. 2 ls neutres (blanc) d. 1 l de charge (rouge) 4. Dconnectez le cblage de lancien botier. 5. Connecter linterrupteur Wi-Fi aux ls existants :
a. Connecter le l de mise la terre (vert, A) de linterrupteur celui du boitier dinterrupteur. panneau lectrique. b. Connecter le l de phase (noir, D) de linterrupteur celui du c. Connecter les ls neutres (blanc, B) de linterrupteur et du luminaire celui du panneau lectrique. d. Connecter le l de charge (rouge, E) de linterrupteur celui du luminaire. 6. Le l de navette (brun, C) doit tre couvert dun capuchon de connexion, mme sil nest pas utilis. 7. Rtablir lalimentation au panneau lectrique pour vrier si linterrupteur fonctionne. 1. Insert the On/Off switch into the switch box. DO not pinch any wires and ensure they are arranged neatly. 2. Ensure the On/Off switch has the Up marking facing up and attached to the switch box with the 2 screws (M). 3. Place the back piece over the On/Off switch and secure with the 2 4. With the top marking facing up, snap on the screwless faceplate on screws (N). the On/Off switch. 1 INTERRUPTEURS INTELLIGENTS 3-VOIES Connexion deux voies Pour la rnovation :
1. Retirez du mur la plaque murale existante ainsi que les vis aprs avoir mis lalimentation hors tension 2. Retirez le gradateur existant du mur et apposez les tiquettes autocollantes appropries sur les ls (comprises dans la boite). 3. Sassurer que les ls suivants sont disponibles :
a. Interrupteur intelligent :
i. 1 l de phase (noir) ii. 1 l de mise la terre (vert, ou jaune/vert) iii. 2 ls neutres (blanc) iv. 1 l de charge (rouge) v. 1 l de navette (brun) b. Interrupteur standard :
i. 1 l de phase (noir) ii. 1 l de mise la terre (vert, ou jaune/vert) iii. 1 l de navette (brun) 4. Dconnectez le cblage de lancien botier. 5. Connecter linterrupteur Wi-Fi aux ls existants :
a. Connecter le l de mise la terre (vert, A) de linterrupteur intelligent celui de linterrupteur standard, puis celui du panneau lectrique. b. Connecter le l de phase (noir, D) de linterrupteur intelligent celui de linterrupteur standard, puis celui du panneau lectrique. c. Connecter les ls neutres (blanc, B) de linterrupteur et du luminaire celui du panneau lectrique. d. Connecter le l de charge (rouge, E) de linterrupteur celui du e. Connecter le l de navette (brun, C) du nouvel interrupteur celui de 6. Assurez-vous que les crous de l inclus sont bien xs chaque l. 7. Insrez la nouvelle gradateur dans le mur. Couvrez avec la plaque murale 8. Insert the new switch into the wall. Cover with the wall plate and screws luminaire. linterrupteur existant. et les vis fournies. provided. 2 INTERRUPTEURS INTELLIGENTS noter que pour crer une connexion trois voies fonctionnelle, il faut utiliser des interrupteurs intelligents de mme marque. Cet interrupteur nest pas compatible avec des interrupteurs dautres marques. Pour la rnovation :
1. Retirez du mur la plaque murale existante ainsi que les vis aprs avoir mis lalimentation hors tension 2. Retirez le gradateur existant du mur et apposez les tiquettes autocollantes appropries sur les ls (comprises dans la boite). 2 1 Premier interrupteur intelligent :
i. 1 l de phase (noir) ii. 1 l de mise la terre
(vert, ou jaune/vert) iii. 1 l neutre (blanc) iv. 1 l de navette (brun) Deuxime interrupteur intelligent
(connect au luminaire) :
i. 1 l de phase (noir) ii. 1 l de mise la terre (vert, ou jaune/vert) iii. 2 ls neutres (blanc) iv. 1 l de charge (rouge) v. 1 l de navette (brun) 3. Dconnectez le cblage de lancien botier. 4. Connexion du gradateur Wi-Fi aux ls existants :
a. Connecter le l de mise la terre (vert, a) des deux interrupteurs celui du panneau lectrique. b. Connecter les ls de phase (noir, D) des deux interrupteurs celui du panneau lectrique. c. Connecter les ls neutres (blanc, B) du deuxime interrupteur et du luminaire celui du panneau lectrique. d. Connecter les ls neutres (blanc, B) du premier interrupteur et du luminaire celui du panneau lectrique. e. Connecter le l de charge (rouge, E) du deuxime interrupteur celui du luminaire. f. Connecter le l de navette (brun, C) du premier interrupteur celui du deuxime interrupteur. 5. Ensure the included wire nuts are securely fastened to each wire. 6. Rtablir lalimentation au panneau lectrique pour vrier si linterrupteur fonctionne. 7. Insrez la nouvelle gradateur dans le mur. Couvrez avec la plaque murale et les vis fournies. INSTALLER LA PLAQUE MURALE 1. Insrer linterrupteur dans le boitier dinterrupteur. Ne PAS pincer les ls;
les placer soigneusement. 2. Sassurer que la marque indiquant le haut de linterrupteur est bien place sur le dessus, et que ce dernier est x au boitier laide des deux vis (M). 3. Placer la plaque arrire sur linterrupteur, puis la xer avec les deux vis (N). 4. Avec la marque indiquant le haut sur le dessus, appuyer sur la plaque avant sans vis pour la xer linterrupteur. 1. Tlcharger lapplication Alexa dAmazon. CONNECTING INSTRUCTIONS 2. Allumer lappareil. Sassurer quil a t install correctement, selon les instructions de la section Installation . 3. Balayer le code barres. Lancer lapplication Alexa dAmazon. Slectionner Add a Device (Ajouter un appareil). Slectionner Bulb (ampoule), trouver Globe Electric et suivre les instructions de lapplication pour balayer le code barres 2D. QR Please keep these instructions in a safe place. This is the only duplicate of the unique QR code for your product. You may need it to reconnect the product to your account or transfer it to another account. Note :
Une fois allum, lappareil se met automatiquement en mode couplage pendant 5 minutes. Au balayage du code barres, la lumire blanche clignotera pour indiquer que le couplage a russi. Si lappareil ne se connecte pas dans ces cinq minutes, lteindre puis le rallumer pour ractiver le mode couplage. Pas de code-barres?
Slectionner Dont have a barcode? (Pas de code-barres?) dans lapplication Alexa et suivre les instructions dans l'application pour savoir comment coupler sans code-barres 2D. 50457 Rinitialisation de lappareil En cas de problme durant la conguration, ou si lappareil tait dj connect un autre rseau, rinitialiser lappareil selon les instructions suivantes :
1. Laisser lappareil allum pendant 10 secondes. 2. teindre et rallumer lappareil cinq fois. La lumire clignotera en ROUGE, puis passera au BLANC, signe que la rinitialisation a russi. 3. Balayer le code-barres qui se trouve dans le manuel d'instructions et connecter lappareil dans les cinq minutes, sans quoi il vous faudra teindre puis rallumer lappareil de nouveau pour ractiver le mode couplage. La lumire clignotera en BLANC pour indiquer que le couplage a russi. instructions ci-dessous :
1) Appuyez simultanment sur les boutons + et - pendant 5 secondes. Le voyant d'tat clignote rapidement. 2) Maintenez la touche + ou - enfonce pour rgler le niveau de luminosit le plus faible. Rglez la lumire jusqu' ce que le clignotement cesse. 3) Pour sortir de ce mode, rptez l'tape 1 jusqu' ce que le voyant d'tat cesse de clignoter (il reste allum). Check out product videos on our Youtube channel, from the Globe x Amazon Alexa -
Smart Devices playlist. INTERRUPTEUR MARCHE/ARRT FCC This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment IC IC STATEMENT This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause undesired operation of the device Cet appareil contient des metteurs / rcepteurs exempts de licence conformes aux RSS (RSS)d'Innovation, Sciences et Dveloppement conomique Canada. Le fonctionnement est soumis aux deux conditions suivantes :
(1) Cet appareil ne doit pas causer d'interfrences.
(2) Cet appareil doit accepter toutes les interfrences, y compris celles susceptibles de provoquer un fonctionnement indsirable de l'appareil.